Northern Industrial Tools 4200NH manuale d’uso

www .makitatoo ls.co m Cir cular Sa w 110 mm (4- 3/8”) MODEL 4200NH DOUBLE INSULA TION INSTR UCTION MANU AL WA R N I N G : F or your personal safety , READ and UNDERST AND before using. SA VE THESE INSTRUCTIONS FOR FUTURE REFERENCE.[...]

2 SPECIFICATIONS • Manufacturer reser ves the ri ght to chan ge specific ations wit hout notice. • Specificat ions may diff er from coun tr y to countr y . GENERAL SAFET Y R ULES USA002-2 (F or All T ools ) W ARNING: Read and under stand all instructions. F ailure to f ollo w all instructions listed below , ma y result in electric shock, fire a[...]

3 6. Do not expose power tools to rain or wet conditions. W ater entering a po wer tool will increase the risk of electric shock . 7. Do not abuse the cor d. Never use the cor d to carry the tools or pull the plu g from an outlet. Keep cor d awa y from heat, oil, sharp edges or moving parts. Replace damaged cor ds immediatel y . Damaged cords incre[...]

4 24. When servicing a tool, us e only identic al replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to f ollo w Maintenance in structions ma y create a risk of electric shock or injury . USE PROPER EXTENSION CORD: Make sure your e x tension cor d is in good cond ition. When using [...]

5 not touch tool housing. Lea ving b lade ex posed is VER Y D ANGEROUS and can lead to serious personal injury . 3. Check the operati on and condition of the lower guar d spring. If the guard and the spring are not operating pro perly , they must be service d before us e. Lower guard ma y operat e sluggishly due to damaged par ts, gumm y deposits ,[...]

6 Do not use dull or damaged blade. Unsharpened or improperly set blades pro- duce narrow k erf caus ing e xcessiv e friction, blade bin ding an d KICKB ACK. K eep blade sharp and clean. Gum and w ood pitc h hard- ened on bla des slows s aw and i ncreases potential f or kic kbac k. K eep b lade clean b y first remo ving it from to ol, then cleani n[...]

7 16. Place the wider portion of the saw base on that part of the workpiece which is so lidly supported, not on the section that will fall off when the cut is made. As example s, Fig. 5 illustrates the RIGHT way to cut off the end of a board, and Fig. 6 the WRONG way . If the workpiece is short or small, clamp it down. DO NO T TRY T O HOLD SHORT PI[...]

8 SA VE THESE INSTR UCTIONS W ARNING: MISUSE or failure to follow the safety rules stated in this instruction man ual ma y cause seriou s per sonal injury . SYMBOLS USD201-2 The followings show the symbols used for tool. V ....................... v olts A ....................... amp eres Hz ..................... hertz ................ alternating c[...]

9 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure th at the tool is s witc hed off and unplugged before adjust ing or checking functi on on the tool. Adjusting depth of cut CA UTION: • After adjusting the de pth of cut, alw a ys tigh ten the clamping sc rew securely . Loosen the c lamping screw on the d epth guide and mov e the base up or do[...]

10 Switch action CA UTION: • Be fore plugging in the tool, alwa ys check to see that the s witch t rigger actua tes properly a nd returns to the “O FF” position whe n released . T o pre vent the s witch trig ger from being ac cidentally pu lled, a lock-off button is provided. T o star t the tool, push i n the lock- off b utton and pul l the s[...]

11 OPERA TION CA UTION: • B es u r et om o v et h et o o lf o r w a r di nas t r a i g h tl i n eg e n t l y . F orcing or twi sting the to ol will resul t in ov erheating the motor and da ngerous kickback, possibly causin g sev ere injury . Hold the tool f irml y . The tool is provided wit h both a front gr ip and rear handle. Use both t o best [...]

12 Adjusting for accuracy of 90° cut (ver tical cut) This adjus tment has bee n made at the f actor y . But if it is off , adjust the ad justing s crew with a screwdri ver while squari ng the blade with the bas e using a tr iangula r rule, tr y squa re, etc. Replacing carbon brushes Remov e and check the carbon bru shes regula rly . Replace when t[...]

13 A CCESSORI ES CA UT ION: • Th ese accessor ies or attach ments are recommend ed f or use with your Makita t ool specifie d in this manual. The use of any other acces sori es or attachm ents might present a r isk of inju r y to persons. Only u se accessor y or attach ment for its stated pur pose. If you need any assistance for more deta ils reg[...]

14 Memo[...]

15 Memo[...]

16 Memo[...]

17 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut[...]

18 1. This pr oduct was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn of about this pr oduct: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom F riend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction [...]

19 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS PORTION FOR Y OUR RECORDS ALABAMA 2365 Pelham P arkway Pelham, AL 35124 (205) 620-1791 ARIZONA 3707 E. Broadw ay Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 ARKANSAS Shackleford Shopping Center 240 South Shackleford Rd., Ste. C Little Rock, AR 72211 (501) 224-5733 CALIFORNIA 41850 Christ[...]

W ARNING Some dust created by po wer sanding, sa wing, grinding, drilling, and other construction activities contains chemicals known to the State of Calif ornia to cause cancer , bir th def ects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and othe[...]