Onkyo HT-S5100 manuale d’uso

E n 7.1ch Home Theater System HT -S5100 AV Receiv er (HT -R560) Speaker P ackage (HTP-560) Front Speak ers (SKF-560F L/R) Center Speaker (SKC-560C) Surround Speak ers (SKM-560S L/R) Surround Back Speak ers (SKB-560 L/R) Subwoofer (SKW -560) Dock f or iPod (DS-A1L) Instruction Manual Thank you for purchasing an Onkyo 7.1ch Home Theater System. Pleas[...]

2 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follo w all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any v entilation openings. Install in accordance with the manufacturer’ s instructions. 8. Do not install near an y heat [...]

3 Precautions 1. Recording Copyright —Unless it’ s for personal use only , recording copyrighted material is illegal with- out the permission of the copyright holder . 2. A C Fuse —The A C fuse inside the unit is not user- serviceable. If you cannot turn on the unit, contact your Onkyo dealer . 3. Care —Occasionally you should dust the unit[...]

4 Precautions —Continued F or British models Replacement and mounting of an A C plug on the power supply cord of this unit should be performed only by qualified service personnel. IMPOR T ANT The wires in the mains lead are coloured in accordance with the following code: Blue: Neutral Brown: Li ve As the colours of the wires in the mains lead of[...]

5 Pa ck ag e Contents Make sure you ha ve the follo wing items: AV Receiver HT -R560 HT -R560 Remote controller and tw o batteries (AA/R6) Speaker setup microphone Indoor FM antenna AM loop antenna Po wer-plug adapter Only supplied in cer tain countries. Use this adapter if your A C outlet does not match with the plug on the A V receiver’ s power[...]

6 Pa ck ag e Contents —Continued * In catalogs and on packaging, the letter at the end of the product name indicates the color . Specifications and operation are the same regardless of color . Dock f or iP od DS-A1L HT-S5100_En.book Page 6 Thursday, March 6, 2008 3:24 PM[...]

7 Using T wo Sets of Speaker s Y ou can use tw o sets of speakers with the A V recei ver: speak er set A and speak er set B . Speaker set A should be used in your main listening room for up to 7.1-channel playback. *While speaker set B is on, speaker set A is reduced to 5.1-channel playback. Speaker set B can be used in another room and offers 2-ch[...]

8 Features Amplifier • 75 W atts/Channel @ 8 ohms (FTC) • 130 W atts/Channel @ 6 ohms (IEC) • WRA T -W ide Range Amplifier T echnology (5Hz–100kHz bandwidth) • High-Current Low-Impedance Dri ve • Optimum Gain V olume Circuitry • H.C.P .S. (High Current Po wer Supply) Massive High Power T ransformer Processing • Dolby Digital EX an[...]

9 Features —Continued *3 Music Optimizer™ is a trademark of Onkyo Corporation. *4 HDMI, the HDMI logo and High Definition Multimedia Inter - f ace are trademarks or registered trademarks of HDMI Licens- ing, LLC. *5 ©2005 SIRIUS Satellite Radio Inc. “SIRIUS, ” SiriusConnect, the SIRIUS dog logo, channel names and logos are trademarks of S[...]

10 Contents Important Safety Instructions .......................... 2 Precautions ....................................................... 3 Speaker Precautions ........................................ 4 Package Contents ............................................ 5 AV Receiver HT-R560 ........................................... 5 Speaker Package [...]

11 Contents —Continued Recording ........................................................ 73 Recording the Input Source ................................... 73 Recording from Different AV Sources ................. 73 Adjusting the Listening Modes ..................... 74 Using the Audio Adjust Settings ........................... 74 Using the Audi[...]

12 Getting to Kno w the A V Receiver The actual front panel has various logos printed on it. They are not shown here for clarity . The page numbers in parentheses show where you can find the main e xplanation for each item. A ON/ST ANDBY button (41) Sets the A V receiv er to On or Standby . B ST ANDBY indicator (41) Lights up when the A V receiv e[...]

13 Getting to Know the A V Receiver —Continued For detailed information, see the pages in parentheses. I MASTER V OLUME control (47) Sets the volume of the A V recei ver to Min, 1 through 79, or Max. J PHONES jack (49) This 1/4-inch phone jack is for connecting a stan- dard pair of stereo headphones for priv ate listening. K SPEAKER A B buttons T[...]

14 Getting to Know the A V Receiver —Continued A DIGIT AL IN OPTICAL 1 and 2 These optical digital audio inputs are for connecting components with an optical digital audio output, such as a CD player or D VD player . They’ re assign- able, which means you can assign each one to an input selector to suit your setup. See “Digital Input Setup”[...]

15 Getting to Know the A V Receiver —Continued M T APE IN/OUT These analog audio input and output jacks are for connecting a recorder with an analog audio input and output, such as a cassette deck, MD recorder , etc. N CBL/SA T IN A cable or satellite receiv er can be connected here. There are S-V ideo and composite video input jacks for connecti[...]

16 Speaker P ac kage For detailed information, see the pages in parentheses. A ST ANDBY/ON indicator Red: Subwoofer in standby mode Blue: Subwoofer on W ith the Auto Standby function, the SKW -560 automatically turns on when an input signal is detected in Standby mode. When there’ s no input signal for a while, the SKW -560 automatically enters S[...]

17 Speaker P ackage —Continued 1 Ke yhole slots These keyhole slots can be used to w all-mount the speaker . See page 24 for mounting instructions. 2 Speaker terminals These push terminals are for connecting the speaker to the HT -R560 with the supplied speaker cables. The supplied speaker cables are color -coded for easy identification. Simply [...]

18 Remote Contr oller ■ Controlling the receiver For detailed information, see the pages in parentheses. A ON/ST ANDBY button (41) Sets the A V receiver to On or Standby . B REMO TE MODE/INPUT SELECTOR b uttons (47, 84–89) Selects the remote controller modes and the input sources. C MUL TI CH button (47) Selects the multichannel D VD input. D S[...]

19 Remote Controller —Continued To control your iPod when it’ s seated in the supplied DS-A1L Dock, which is connected to the HT -R560’ s DOCK jack, press the [DOCK] REMO TE MODE but- ton. See page 37 for details on connecting the DS-A1L Dock. To control an RI Dock other than the DS-A1L, see “Con- trolling Other Components” on page 82. A [...]

20 Remote Controller —Continued Notes: • If the remote controller doesn’t w ork reliably , try replacing the batteries. • Don’t mix ne w and old batteries or different types of batteries. • If you intend not to use the remote controller for a long time, remov e the batteries to prev ent damage from leakage or corrosion. • Expired batt[...]

21 Connecting Y our Speakers Thanks to the A V receiv er’ s superb capabilities, you can enjoy surround sound with a real sense of mov ement in your own home—just lik e being in a movie theater or concert hall. Y ou can enjoy D VDs featuring Dolby Digital or DTS. W ith analog or digital TV , you can enjoy Dolby Pro Logic IIx, DTS Neo:6, or Onky[...]

22 Connecting Y our Speakers —Continued Speaker Configuration For 7.1-channel surround-sound playback, you need sev en speakers and a powered subwoofer . The following table sho ws which channels you should use based on the number of speakers you ha ve. * If you’ re using only one surround back speaker , connect it to the SURR B A CK L termina[...]

23 Connecting Y our Speakers —Continued Note: While speaker set B is on, speaker set A is reduced to 5.1-channel playback. Connecting Speaker Set A 1 Strip 5/8" (15 mm) of insu- lation from the ends of the speaker cables, and twist the bare wires tightly , as shown. 2 Unscrew the terminal. Fully insert the bare wire, making sure that it’ s[...]

24 Connecting Y our Speakers —Continued The speakers can easily be wall mounted by using the ke yhole slots. To mount the front or surround speakers vertically , use the keyhole slot sho wn to hang each speaker on a screw that’ s securely screwed into the w all. Front speak er (SKF-560F) Surround speak er/ Surround back speaker (SKM-560S/SKB-56[...]

25 Connecting Antennas This section explains ho w to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially av ailable outdoor FM and AM antennas. The A V receiv er won’ t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner . The supplied indoor FM antenna [...]

26 Connecting Antennas —Continued If you cannot achiev e good reception with the supplied indoor FM antenna, try a commercially av ailable out- door FM antenna instead. Notes: • Outdoor FM antennas work best outside, b ut usable results can sometimes be obtained when installed in an attic or loft. •F or best results, install the outdoor FM an[...]

27 Connecting Y our Components • Before making any A V connections, read the manuals supplied with your other A V components. • Don’t connect the po wer cord until you’ ve completed and double-checked all A V connections. Optical Digital Jacks The A V receiv er’ s optical digital jacks hav e shutter-type cov ers that open when an optical [...]

28 Connecting Y our Components —Continued By connecting both the audio and video outputs of your D VD player and other A V components to the A V recei ver, you can switch the audio and video signals simultaneously simply by changing the input source on the A V receiv er. The A V receiv er supports sev eral connection formats for compatibility wit[...]

29 Connecting Y our Components —Continued •T o enjoy Dolby Digital and DTS, use connection or . If your TV has no audio outputs, connect an audio output from your VCR or cable or satellite receiv er to the A V recei ver and use its tuner to listen to TV programs through the A V recei ver (see pages 32 and 34). Connecting a TV or Projector Conne[...]

30 Connecting Y our Components —Continued •T o enjoy Dolby Digital and DTS, use connection or . • If your D VD player has main left and right outputs and multichannel left and right outputs, be sure to use the main left and right outputs for connection . Connecting a D VD player Connection A V receiver Signal flow DVD pla yer Picture quality[...]

31 Connecting Y our Components —Continued Hooking Up the Multichannel Input If your D VD player supports multichannel audio formats such as DVD-Audio and SA CD, and it has a multichannel analog audio output, you can connect it to the A V receiv er’ s multichannel input. Use a multichannel analog audio cable, or sev eral normal audio cables, to [...]

32 Connecting Y our Components —Continued W ith this hookup, you can use the tuner in your VCR or D VR to listen to your fav orite TV programs via the A V receiv er, which is useful if your TV has no audio outputs. •T o enjoy Dolby Digital and DTS, use connection or . Connecting a VCR or D VR for Pla yback Connection A V receiver Signal flow V[...]

33 Connecting Y our Components —Continued Notes: • The A V receiver must be turned on for recording. Recording is not possible while it’ s on Standby . • If you want to record directly from your TV or another video source without going through the A V receiver , connect the audio and video outputs from your TV or other video component direc[...]

34 Connecting Y our Components —Continued W ith this hookup, you can use your satellite or cable receiver to listen to your f av orite TV programs via the A V receiv er, which is useful if your TV has no audio outputs. •T o enjoy Dolby Digital and DTS, use connection or . Connecting a Satellite, Cable, or T errestrial Set-top box or Other Video[...]

35 Connecting Y our Components —Continued About HDMI Designed to meet the increased demands of digital TV , HDMI (High Definition Multimedia Interface) is a ne w digital interface standard for connecting TVs, projectors, D VD players, set-top boxes, and other video components. Until now , sev eral separate video and audio cables have been requir[...]

36 Connecting Y our Components —Continued If you hav e an HDMI-compatible player, you can connect it to the A V recei ver with an HDMI cable. ■ A udio Signals • Audio and video signals receiv ed via inputs other than the HDMI IN jacks are not output by the HDMI OUT . • Audio and video signals receiv ed via the HDMI IN jacks are output only [...]

37 Connecting Y our Components —Continued Notes: •T o connect an RI dock other than the DS-A1L, refer to its instruction manual. • While your iPod is seated in the Dock, its battery will be charged when the A V recei ver is set to On or Standby . Connecting a Camcorder , Game Console, or Other Device Connection A V receiver Signal flow Camco[...]

38 Connecting Y our Components —Continued ■ CD Play er or T urntable (MM) with Built-in Phono Preamp •T o connect the CD player digitally , use connection or . ■ T urntable (MM) with no Phono Preamp Built-in A phono preamp is necessary to connect a turntable that doesn’t ha ve a phono preamp built-in. ■ T urntable with an MC (Mo ving Co[...]

39 Connecting Y our Components —Continued •T o connect the recorder digitally for playback, use connections and , or and . Connecting a Cassette, CDR, MiniDisc, or D A T Recorder Connection A V receiver Signal flow Cassette, CDR, MD, or DA T recorder T APE IN L/R T APE OUT L/R ⇐ ⇒ Analog audio L/R output Analog audio L/R input DIGIT AL IN [...]

40 Connecting Y our Components —Continued W ith (Remote Interactive), you can use the follo wing special functions: Auto P ower On/Standb y When you start playback on a component connected via , if the A V receiv er is on Standby , it will automatically turn on and select that component as the input source. Similarly , when the A V recei ver is s[...]

41 T urning On the A V Receiver ON/STANDBY STANDBY SPEAKERS T ONE MOVIE/TV MUSIC GAME DISPLAY RT/PTY/TP MEMORY CLEAR DIGITAL INPUT TUNING MODE B A PHONES MULTI CH DOCK DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD SETUP SETUP MIC VIDEO L AUDIO R A UX INPUT ENTER RETURN TUNING PRESET MASTER VOLUME AV RE CEIVER HT-R560 ON/STANDBY RECEIVER ON/STANDBY ST ANDBY[...]

42 Fir st Time Setup This section explains the settings that you need to make before using the A V recei ver for the very first time. W ith the supplied calibrated microphone, Audyssey 2EQ automatically determines the number of speakers con- nected, their size for purposes of bass management, optimum crossov er frequencies to the subwoofer (if pre[...]

43 First Time Setup —Continued Note: • When the automatic speaker setup is complete, the Equalizer Settings (page 81) will be set to “ Audyssey . ” Error Messa g es While the automatic speaker setup is in progress, one of the following error messages may appear: Ambient noise is too high This message appears if there’ s too much backgroun[...]

44 First Time Setup —Continued Using a P owered Subwoof er If you’ re using a powered subwoofer , as it outputs very low-frequenc y sound and its position is usually low down, it may not be detected by the automatic speaker setup. In this case, increase the subwoofer’ s volume, select its highest crossover frequenc y , and then try running th[...]

45 First Time Setup —Continued If you connect a video component to a COMPONENT VIDEO IN, you must assign that input to an input selector . For example, if you connect your D VD player to COMPONENT VIDEO IN 2, you must assign COM- PONENT VIDEO IN 2 to the D VD input selector . By default, the D VD input selector is assigned to COM- PONENT VIDEO IN[...]

46 First Time Setup —Continued If you connect a component to a digital audio input, you must assign that input to an input selector . For example, if you connect your CD player to OPTICAL IN 1, you must assign OPTICAL IN 1 to the CD input selector . These are the default assignments. Note: • This procedure can also be performed on the A V recei[...]

47 Pla ying Y our A V Components Basic A V Receiver Operation ON/STANDBY STANDBY SPEAKERS T ONE MOVIE/TV MUSIC GAME DISPLAY RT/PTY/TP MEMORY CLEAR DIGITAL INPUT TUNING MODE B A PHONES MULTI CH DOCK DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD SETUP SETUP MIC VIDEO L AUDIO R A UX INPUT ENTER RETURN TUNING PRESET MASTER VOLUME AV RE CEIVER HT-R560 3 1 3 1 O[...]

48 Common Functions This section explains functions that can be used with an y input source. Y ou can adjust the brightness of the display . Y ou can temporarily mute the output of the A V recei ver. To unmute the A V receiver, press the remote control- ler’ s [MUTING] button again, or adjust the v olume. The output is unmuted and the MUTING indi[...]

49 Common Functions —Continued 7 For pri vate listening, you can connect a pair of stereo headphones (1/4-inch phone plug) to the A V receiv er’ s PHONES jack. Notes: •A lw ays turn down the v olume before connecting your headphones. • While the headphones plug is inserted in the PHONES jack, the speakers are turned of f. • When you conne[...]

50 Common Functions —Continued The following table sho ws the display indicator for each digital signal format. Normally , the A V recei ver detects the format of digital input signals automatically . Howev er, if you e xperience either of the following issues when playing PCM or DTS sources, you can specify the signal format manually . • If th[...]

51 Listening to the Radio For AM tuning to work properly , you must specify the AM frequency step used in your area. Note that when this setting is changed, all radio presets are deleted. Note: • This procedure can also be performed on the A V receiv er by using its [SETUP], [ENTER], and arrow buttons. AM Frequency Step Setup (on some models) 1 P[...]

52 Listening to the Radio —Continued W ith the built-in tuner , you can enjoy AM and FM radio stations and store your fa vorite stations as presets for easy selection. T uning into AM/FM Radio Stations ■ A uto T uning Mode When tuned into a station, the TUNED indicator appears. When tuned into a stereo FM station, the FM STEREO indicator also a[...]

53 Listening to the Radio —Continued ■ T uning into Stations by Frequenc y Y ou can tune into AM and FM stations directly by enter- ing the appropriate frequency . Displaying AM/FM Radio Inf ormation 1 Press the [TUNER] button repeat- edly to select AM or FM, follo wed by the [D.TUN] b utton. (Actual display depends on country .) 2 Within 8 sec[...]

54 Listening to the Radio —Continued Y ou can store a combination of up to 40 of your f av orite AM and FM radio stations. Deleting Presets Selecting Presets Presetting AM/FM Stations 1 T une into the AM or FM station you want to store as a preset. 2 Press the [MEMOR Y] button. The preset number flashes. 3 While the preset number is flash- ing [...]

55 Listening to SIRIUS Satellite Radio Note: Hardware and required basic monthly subscription are sold separately . Installation costs and other fees and taxes, including a one-time acti vation fee may apply . Subscription fee is consumer only . All fees and pro- gramming are subject to change. What is SIRIUS Satellite Radio? Simply The Best Radio [...]

56 Listening to SIRIUS Satellite Radio —Continued Before you can use SIRIUS Satellite Radio, you must first sign up for an account. Y ou’ ll need a major credit card and your SIRIUS Satellite Radio ID, which you can get from the A V receiv er, as explained belo w , or from the SiriusConnect Home tuner package. Setting the Satellite Radio Mode [...]

57 Listening to SIRIUS Satellite Radio —Continued Note: • After you’ ve acti vated your subscription with SIRIUS Satellite Radio, your SIRIUS Satellite Radio ID num- ber will no longer be displayed when you select chan- nel 0. T o check your ID, you’ll need to; press the [SETUP] button, select “11. SiriusID” with the Up and Down [ ]/[ ][...]

58 Listening to SIRIUS Satellite Radio —Continued Direct T uning Y ou can select a SIRIUS Satellite Radio channel directly by entering its number with the remote control- ler . Notes: • If you select an unav ailable channel, “INV ALID CHANNEL” appears on the display . • If you select a channel that you are not subscribed to, “CALL SIRIU[...]

59 Listening to SIRIUS Satellite Radio —Continued Presetting SIRIUS Channels Y ou can store a combination of up to 40 of your f av orite SIRIUS Satellite Radio channels and AM/FM radio sta- tions as presets. ■ Selecting Presets ■ Deleting Presets Press the [DISPLA Y] b utton repeatedly to cycle through the a vailable information. Note: If the[...]

60 Listening to SIRIUS Satellite Radio —Continued SUB UPDA TED Displayed while your subscription is being updated. No operations can be performed until this message has cleared. UPDA TING XXX% Displayed while the channel map is being updated. W ait until the updating is complete. SIRIUS UPDA TING Displayed while the SiriusConnect receiv er’ s ?[...]

61 Listening to SIRIUS Satellite Radio —Continued Y ou can lock out channels that you do not w ant to receiv e. * The default number is “0000. ” If you want to change the default setting, see “Changing the PIN Number” on page 62. To unlock a previously locked channel , select the locked channel (see step 1–4), press the Left and Right [[...]

62 Listening to SIRIUS Satellite Radio —Continued Changing the PIN Number 1 Press the [RECEIVER] button, follo wed by the [SETUP] button. 2 Use the Up and Down [ ]/[ ] buttons to select “10. Parental Lock, ” and then press [ENTER]. Note: • If the 8. SA T RadioMode is set to None (see page 56), the “Parental- Lock” item is not av ailable[...]

63 Listening to the Radio —Continued RDS only works in areas where RDS broadcasts are av ailable. When tuned to an RDS station, the RDS indi- cator appears. ■ What is RDS? RDS stands for Radio Data System and is a method of transmitting data in FM radio signals. It was de veloped by the European Broadcasting Union (EBU) and is a vail- able in m[...]

64 Listening to the Radio —Continued Displaying Radio T ext (R T) When tuned to an RDS station that’ s broadcasting text information, the text can be displayed. Notes: • The message “W aiting” may appear while the A V receiv er waits for the R T information. • If the message “No T ext Data” appears on the display , no R T informatio[...]

65 DS-A1L Doc k for the iP od W ith the supplied DS-A1L Onkyo Dock, you can easily play the music stored on your Apple iPod through the A V receiv er and enjoy great sound. Y ou can use the A V receiv er’ s remote controller to operate your iPod. ■ Made for: • 5th Generation iPod (iPod with video) • iPod photo (iPod with color display) • [...]

66 DS-A1L Dock f or the iP od —Continued Operating Notes: • Before selecting a different input source, stop iPod playback to prev ent the A V recei ver from selecting the iPod input source by mistake. • If any accessories are connected to your iPod, the A V receiv er may not be able to select the input source properly . • While your iPod is[...]

67 Using the Listening Modes F or a description of each listening mode, see “ About the Listening Modes” on page 71. Selecting on the A V Receiver ■ [MO VIE/TV] button This button selects the listening modes intended for use with movies and TV . ■ [MUSIC] button This button selects the listening modes intended for use with music. ■ [GAME][...]

68 Using the Listening Modes —Continued Analog and PCM Sources Listening Modes A vailable f or Each Source Format Button Source f ormat PCM Multi channel Analog 32–96kHz *1 *1. 32/44/48/88/96kHz Media Listening Mode CD, TV , radio, D VD [MO VIE/TV] Mono ✔ Dolby PLII Mo vie/Dolby PLIIx Mo vie *2 *2. If there are no surround back speakers, or s[...]

69 Using the Listening Modes —Continued Dolby Digital Sour ces Requires 6.1/7.1 speakers. Not available while speaker set B is on. Requires 7.1 speakers. Not available while speaker set B is on. Button Source f ormat Dolby Digital Multichannel 2ch Mono/Multiplex Media Listening Mode DV D, DTV , etc. [MO VIE/T V] Mono ✔✔✔ DolbyDigital ✔ Ne[...]

70 Using the Listening Modes —Continued DTS Sources Requires 6.1/7.1 speakers. Not available while speaker set B is on. Requires 7.1 speakers. Not available while speaker set B is on. Button Source f ormat DTS, DTS 96/24 DTS Discrete/Matrix Multichannel 2ch Mono/Multiplex Media Listening Mode DV D, CD, etc. D VD, CD, etc. [MO VIE/TV] Mono ✔✔?[...]

71 Using the Listening Modes —Continued The A V receiv er’ s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. Direct In this mode, audio from the input source is output directly with minimal processing, providing high-fidel- ity reproduction. All of the sou[...]

72 Using the Listening Modes —Continued DTS Neo:6 This mode expands an y 2-channel source for 7.1-chan- nel playback. It uses sev en full-bandwidth channels of matrix decoding for matrix-encoded material, providing a very natural and seamless surround sound e xperience that fully en velops the listener . • Neo:6 Cinema (NEO:6 Cin) Use this mode[...]

73 Recor ding This section explains ho w to record the input source and how to record audio and video from separate sources. Notes: • The surround sound and DSP listening modes cannot be recorded. • Copy-protected D VDs cannot be recorded. • Sources connected to the analog multichannel input cannot be recorded. • Sources connected to a digi[...]

74 Adjusting the Listening Modes W ith the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like. The Audio Adjust settings are explained belo w . Multiplex/Mono Settings Multiplex ■ Input (Mux) This setting determines which channel of a stereo multi- plex source is output. Use it to select audio channels o[...]

75 Adjusting the Listening Modes —Continued Neo:6 Music ■ Center Image The DTS Neo:6 Music listening mode creates 6-channel surround sound from 2-channel stereo sources. W ith this setting, you can specify by how much the front left and right channel output is attenuated in order to create the center channel. It can be adjusted from 0 to 5. The[...]

76 Adjusting the Listening Modes —Continued Late Night Function ■ Late Night W ith the Late Night function, you can reduce the dynamic range of Dolby Digital material so that you can still hear quiet parts ev en when listening at low volume lev els—ideal for watching movies late at night when you don’t w ant to disturb anyone. For Dolby Dig[...]

77 Ad v anced Setup This section explains ho w to check the speaker settings and how to set them manually , which is useful if you change a speaker after performing the automatic speaker setup. Some of the speaker settings are set automatically by the Automatic Speaker Setup function (see page 42). Speaker Configuration This section explains ho w [...]

78 Adv anced Setup —Continued Note: • These settings cannot be changed while headphones are connected or the multichannel D VD input is being used. Crosso ver Frequency This setting only applies to the speakers that you speci- fied as Small in the “Speaker Configuration” on page 77. To get the best bass performance from your speaker sys- [...]

79 Adv anced Setup —Continued Double Bass W ith the Double Bass function, you can boost bass out- put by feeding bass sounds from the front left, right, and center channels to the subwoofer . This function can be set only if the Subwoofer setting (step 3) is set to Y es, and the Front setting (step 4) is set to Large in the Speaker Configuration[...]

80 Adv anced Setup —Continued Speaker Levels Y ou can set the v olume level of each speak er so that all speakers can be heard equally at the listening position. Note: • The speaker le vels cannot be adjusted while a pair of headphones is connected or the A V receiv er is muted. • While speaker set B is on, you can adjust the v olume of the l[...]

81 Adv anced Setup —Continued Equalizer Settings Here you can adjust the tone of individual speak ers. T o set the volume of indi vidual speakers, see page 80. Notes: • The front, center , surround, and surround back speak- ers can be adjusted at 80Hz, 250Hz, 800Hz, 2500Hz, and 8000Hz. The subw oofer can be adjusted at 40Hz, 80Hz, and 160Hz. ?[...]

82 Contr olling Other Components Y ou can control your D VD player , CD player, and other components with the A V receiv er’ s remote controller . To control another component, you must first enter that component’ s remote control code to a REMO TE MODE button. This section explains ho w to enter remote control codes and how to control your ot[...]

83 Controlling Other Components —Continued Remote Control Codes f or Onkyo Components Connected via Onkyo components that are connected via are con- trolled by pointing the remote controller at the A V receiv er, not the component. This allows you to control components that are out of view , in a rack, for example. If you want to control an Onkyo[...]

84 Controlling Other Components —Continued By pressing the REMO TE MODE button that’ s been programmed with the remote control code for your D VD player (HD D VD, Blu-ray , or TV/D VD combination), you can control your player with the following b uttons. The [D VD] REMOTE MODE b utton is preprogrammed with the remote control code for controllin[...]

85 Controlling Other Components —Continued T PLA Y MODE b utton Selects play modes on components with selectable play modes. U CLR button Cancels functions and clears entered numbers. Note: • If you enter the remote control code for a HD D VD or Blu-ray player that has A, B, C, and D buttons, the [SEARCH], [REPEA T], [RANDOM], and [PLA Y MODE] [...]

86 Controlling Other Components —Continued By pressing the REMO TE MODE button that’ s been programmed with the remote control code for your sat- ellite receiv er, cable recei ver , or DVD recorder (DBS/PVR combination or cable/PVR combination), you can control your player with the following b uttons. F or details on entering a remote control c[...]

87 Controlling Other Components —Continued By pressing the REMO TE MODE button that’ s been programmed with the remote control code for your CD player , CD recorder, or MD player , you can control your player with the following b uttons. The [CD] REMO TE MODE button is preprogrammed with the remote control code for controlling an Onkyo CD playe[...]

88 Controlling Other Components —Continued By pressing the REMO TE MODE button that’ s been programmed with the remote control code for your cas- sette recorder , you can control your cassette recorder with the following b uttons. The [T APE] REMO TE MODE button is preprogrammed with the remote control code for controlling an Onkyo cassette rec[...]

89 Controlling Other Components —Continued By pressing the [TV] REMO TE MODE button that’ s been programmed with the remote control code for your TV (TV/D VD combination or TV/VCR combination), you can control your TV with the follo wing buttons. F or details on entering a remote control code for a dif fer- ent component, see page 82. A ON/ST A[...]

90 Tr oubleshooting If you hav e any trouble using the A V receiver, look for a solution in this section. If you can’t resolv e the issue yourself, contact your Onkyo dealer . Can’t turn on the A V receiver • Make sure that the po wer cord is plugged into the wall outlet properly . • Unplug the power cord from the w all outlet, wait 5 secon[...]

91 Tr oubleshooting —Continued The surround bac k speakers produce no sound • The surround back speakers are not used with all lis- tening modes. T ry another listening mode (page 67). • Not much sound may be produced by the surround back speakers with some sources. • Check the Speaker Configuration (page 77). • While speaker set B is on[...]

92 Tr oubleshooting —Continued Reception is noisy , stereo FM reception suffers from hiss, or the FM STEREO indicator doesn’t light up • Relocate your antenna. •M ove the A V receiver a way from your TV or com- puter . • When listening to an AM station, operating the remote controller may cause noise. •P assing cars and airplanes can ca[...]

93 Specifications Amplifier Section Video Section T uner Section ■ FM ■ AM General ■ Video Inputs ■ Video Outputs ■ A udio Inputs ■ A udio Outputs ■ Control T erminal Specifications and features are subject to change without notice. HT -R560 Rated Output Power North American: 110 watts minimum continuous power per channel, 8 ohm lo[...]

94 Specifications —Continued ■ Subwoof er (SKW -560) ■ Front Speaker (SKF-560F) ■ Center Speaker (SKC-560C) ■ Surround/Surr ound Back Speaker (SKM-560S/SKB-560) Specifications and features are subject to change without notice. 7.1ch Home Theater Speaker P acka g e T ype: Bass-reflex Input sensitivity/ Impedance: 140 mV/20 k Ω Maximum[...]

95 Memo HT-S5100_En.book Page 95 Thursday, March 6, 2008 3:24 PM[...]

96 SN 29344669 I0802-1 (C) Copyright 2008 ONKY O CORPORA TION Japan. All rights reser ved. http://www.onky o.com/ HOMEP AGE Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8163 ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: [...]