Panasonic WV-NS202 manuale d’uso

LOCK WV-NS202 OPEN Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. Network Camera Network Operating Instructions Model No. WV -NS202[...]

2 CONTENTS Preface ....................................................................................................................... ..... 3 About these operating instructions .............................................................................. 3 Trademarks and Registered Trademarks ..................................................[...]

3 Preface About these operating instructions There are 2 sets of operating instructions for the WV-NS202 as follows. • Installation Guide • Network operating instructions These network operating instructions contain descriptions of how to operate this product using a PC via a network and of how to configure the settings. Refer to the installati[...]

4 Monitor Images on a PC The following are descriptions of how to monitor images from the camera on a PC. Monitor images from a single camera Notes: • When "ON" is selected for "User Authentication", the authentication window will be displayed before dis- playing live images for the user name and password entries. The default [...]

5 About the "Live" page q [Setup] button (*1) Click this button to display the setup menu. The but- ton will turn green and the setup menu will be dis- played. w [Live] button Click this button to display the "Live" page. The but- ton will turn green and the "Live" page will be dis- played. e Multi-screen buttons Image[...]

6 u [SD] button (manual SD recording button) (*2) This button will be displayed only when "Manual" is selected for "Save trigger" on the setup menu. ( ☞ page 22) Click this button to manually record images on the SD memory card. Refer to page 10 for descriptions of how to manually record images on the SD memo- ry card. i ZOOM [...]

7 In this case, the camera will not move when the thumbnail image is clicked. (For example, when pre- set position 3 is unregistered, the thumbnail image of preset position 2 will be displayed as the thumb- nail image of preset position 3. The camera will not move when the thumbnail image of preset position 3 is clicked.) • The camera will not al[...]

8 !9 Audio output button (*3) Turns on/off the audio transmission (play audio from the PC on the camera speaker). This button will be displayed only when "Audio output" or "Interactive" is selected for "Audio mode" on the setup menu. ( ☞ page 40) The button blinks while the audio transmission is being carried out. Wh[...]

9 Monitor images from multiple cameras Images from multiple cameras can be displayed on a multi-screen. Images from 4 cameras (up to 16 cameras) can be displayed simultaneously. To display images on a multi-screen, it is necessary to register cameras in advance. 4 cameras can be registered as a group and up to 4 groups (16 cameras) can be registere[...]

10 Record images on the SD memor y card manually Images displayed on the "Live" page can be recorded on the SD memory card manually. This button is operable only when "Manual" is selected for "Save trigger" on the setup menu. ( ☞ page 22) Images recorded on the SD memory card can be copied onto the PC. ( ☞ page 24)[...]

11 Action at an Alarm Occurrence The alarm action will be performed when the following alarms occur. Alarm type Terminal alarm: When connecting an alarm device such as a sensor to the EXT I/O connector 1-3 on the rear of the camera, the alarm action (camera action at an alarm occurrence) will be performed when the connected alarm device is activate[...]

12 T ransmit images onto an FTP ser ver Images can be transmitted to an FTP server. By configuring the following settings, transmission of images captured at an alarm occurrence or captured at a designated interval to an FTP server will become available. Important: • When using this function, set the user name and the password to access the FTP s[...]

13 Save images on the SD memory card when images fail to transmit using the FTP periodic transmission function Images that have failed to transmit using the FTP periodic transmission can be saved automatically on the SD mem- ory card. Images saved on the SD memory card can be obtained from the [SD memory card] tab of the "Basic setup" pag[...]

14 About the network security of the camera Equipped security functions The following security functions are featured in this camera. q Access restrictions by the host authentication and the user authentication It is possible to restrict users from accessing the camera by setting the host authentication and/or the user authentication to "ON&qu[...]

15 Display the setup menu and configure the settings of the camera using a PC The settings of the camera can be configured on the setup menu. The setup menu is only operable by users whose access level is "1. Administrator". How to display the setup menu Step 1 Display the "Live" page. ( ☞ page 4) Step 2 Click the [Setup] butt[...]

16 Step 1 Click the desired button in the frame on the left of the window to display the respective setup menu. When there are tabs at the top of the setup page dis- played in the frame on the right of the window, click the desired tab to display and configure the setting items relating to the name of the tab. Step 2 Complete each setting item disp[...]

17 About the setup menu window q [Live] button Click this button to display the "Live" page. w [Basic setup] button Click this button to display the "Basic setup" page. The basic settings such as time and date and cam- era title, and the settings relating to the NTP server and the SD memory card can be configured on the "Ba[...]

18 i [Network setup] button Click this button to display the "Network setup" page. The network settings and the settings relating to DDNS (Dynamic DNS), SNMP (Simple Network management Protocol) and the FTP (File Transfer Protocol) periodic transmission function can be con- figured on the "Network setup" page. Refer to page 58 f[...]

19 Configure the basic settings of the camera [Basic setup] The basic settings such as time and date and camera name, and the settings relating to the NTP server and the SD memory card can be configured on the "Basic setup" page. The "Basic setup" page has 3 tabs; the [Basic] tab, the [NTP] tab and the [SD memory card] tab. Conf[...]

20 • SD memory card error LED: This LED will light when the SD memory card is unavailable to save images. • Power LED: This LED will light when the power is on. [OSD Position] Select a position where time and date, camera title, pre- set ID, panning/tilting angle, zoom ratio are to be dis- played on the "Live" page. Upper left: The ab[...]

21 Configure the settings relating to the NTP server [NTP] Click the [NTP] tab on the "Basic setup" page. ( ☞ page 15) The settings relating to the NTP server such as the NTP server address, port number, etc. can be configured on this page. [Time adjustment] Select the time adjustment method from the following. Time adjusted by the sele[...]

22 ■ SD memory card setup [SD memory card] Select "Use" or "Not use" to determine whether or not to use the SD memory card. Default: Not use Important: • Before removing the SD memory card from the cam- era, it is necessary to select "Not use" first. • After inserting the SD memory card, it is necessary to select[...]

23 Note: When "FTP error" is selected for "Save trigger", the file name entered for "File name" on the [FTP] tab of the "Network setup" page will be used for the file name of the image saved on the SD memory card. [Frame rate] Select an image save interval from the following. 0.1 fps/0.2 fps/0.33 fps/0.5 fps/[...]

24 Copy images saved on the SD memory card onto the PC [SD memory card images] Click the [SD memory card] tab on the "Basic setup" page. ( ☞ page 15) The following are descriptions of how to copy images saved on the SD memory card onto the PC. It is necessary in advance to select "Allow" for "FTP access" on the [Netw[...]

2 GB 1 GB 512 MB 256 MB 128 MB 64 MB Size of SD memory card 25 Size of SD memory card Approx. 32 000 pics Approx. 16 000 pics Approx. 8 000 pics Approx. 4 000 pics Approx. 2 000 pics Approx. 1 000 pics Approx. 36 000 pics Approx. 18 000 pics Approx. 9 000 pics Approx. 4 500 pics Approx. 2 250 pics Approx. 1 125 pics Approx. 38 000 pics Approx. 19 0[...]

26 Configure the settings relating to images and audio [Camera setup] The settings relating to JPEG/MPEG-4 images and camera operations such as the settings of image quality, preset positions, audio, etc. can be configured on this page. The "Camera setup" page has 4 tabs; the [JPEG/MPEG-4] tab, the [Cam Function] tab, the [Image/Position][...]

27 ■ MPEG-4 setup Configure the settings relating to MPEG-4 image such as "Max bit rate (per 1 client)", "Image capture size", "Image quality", etc. in this section. Refer to page 26 for further information about the settings relating to JPEG images. [MPEG-4 transmission] Select "ON" or "OFF" to d[...]

28 [Unicast port1 (Image)] Enter the unicast port number (used to transmit images from the camera). Available port number: 1024 - 50000 (Only even num- bers are available.) Default: 32004 [Unicast port2 (Audio)] Enter the unicast port number (used to transmit audio from the camera). Available port number: 1024 - 50000 (Only even num- bers are avail[...]

29 Configure the settings relating to the camera title and the camera operations [Cam Function] Click the [Cam Function] tab on the "Camera setup" page. ( ☞ page 15) Configure the settings relating to camera title and the camera operations on this page. [Camera title on screen] Select "ON" or "OFF" to determine wheth[...]

30 [Upside-down] Select "ON (desktop)" or "OFF (ceiling)" to determine how the camera is to be installed. ON (desktop): Select this when the camera is to be installed with the dome side up. OFF (ceiling): Select this when the camera is to be installed with the dome side down. Default: OFF (ceiling) [EL-ZOOM] Select "ON"[...]

31 Configure the settings relating to images and the preset positions [Image/Position] Click the [Image/Position] tab on the "Camera setup" page. ( ☞ page 15) When the [SETUP>>] button of each setting item is clicked, the detailed settings menu will be displayed in a newly opened window. The detailed settings can be configured whi[...]

Configure the settings relating to image quality ("Image Adjust" setup menu) Click the [SETUP>>] button of "Image Adjust" on the [Image/Position] tab of the "Camera setup" page. ( ☞ page 31) The settings relating to image quality can be configured with the setup menu displayed in a newly displayed window. When [...]

33 [White balance] Select a method of white balance adjustment from the following. White color can be adjusted by "Red Gain" and "Blue Gain". ATW1: Auto tracing white balance mode The camera will constantly check the color tempera- ture of the light source and adjust the white balance automatically. Operating color temperature r[...]

34 [DNR (Digital Noise Reduction)] When this function (digital noise reduction) is active, noise may be automatically reduced under a low lumi- nance. Select an effect level "LOW" or "HIGH" for the digital noise reduction. HIGH: High DNR, afterimage remains LOW: Low DNR, reduces afterimage Default: HIGH [Chroma gain level] Adjus[...]

35 Set mask areas When "OFF" is selected for "Super Dynamic 3", it is possible to compensate for backlight by masking brighter areas. Step 1 Display the setup menu of "Image Adjust". ( ☞ page 32) Step 2 Click the [START] button of "Mask area". → Borders will appear and the image displayed on the [Image/Po[...]

36 Configure the settings relating to the preset positions ("Preset No." setup menu) Click the [SETUP>>] button of "Preset Position" on the [Image/Position] tab of the "Camera setup" page. ( ☞ page 31) It is possible to register, edit and delete the preset positions on this page. When the focus, brightness, zoo[...]

37 [Preset ID (0-9, A-Z)] Enter the preset ID to be displayed on images. The pre- set IDs can be applied to each preset position. Available characters: 0-9, A-Z and the following marks. !"#$%& ‘ ()*+,-./:; =? Number of characters for the preset ID: 0 - 16 char- acters Default: None (blank) Note: The entered preset ID will be displayed ne[...]

38 Configure the settings relating to the auto pan function ("Auto Pan" setup menu) Click the [SETUP>>] button of "Auto Pan" on the [Image/Position] tab of the "Camera setup" page. ( ☞ page 31) The settings relating to the auto pan function can be configured with the setup menu displayed in a newly displayed wi[...]

39 Configure the settings relating to the privacy zone ("Privacy Zone" setup menu) Click the [SETUP>>] button of "Privacy Zone" on the [Image/Position] tab of the "Camera setup" page. ( ☞ page 31) When there is a zone that is not to be displayed, set the zone as a privacy zone to not to display. Up to 8 privacy[...]

40 ZOOM buttons FOCUS buttons BRIGHTNESS buttons Control pad/buttons Refer to pages 6 and 7 for descriptions of how to oper- ate these buttons/pad. [CLOSE] button Click this button to close the "Privacy zone" setup menu. Configure the settings relating to audio [Audio] Click the [Audio] tab on the "Camera setup" page. ( ☞ page[...]

41 [Audio output volume (PC to Camera)] Select a volume level on the camera to hear audio transmitted from the PC. Low/Middle/High Default: Middle [Audio output interval (PC to Camera)] Select an interval for audio transmission from the follow- ing. 160 msec/320 msec/640 msec/1 280 msec Default: 640 msec Notes: • When a shorter interval is select[...]

42 Configures the multi-screen settings [Multi-screen setup] The cameras to be used for the multi-screen display can be registered on this page. Refer to page 9 for descriptions of how to display images on a multi-screen. The following cameras are applicable for the multi-screen display. (As of October, 2006) WV-NS202, WV-NP240 series, WV-NP1000 se[...]

43 Configure the alarm settings [Alarm setup] The settings relating to alarm occurrences such as settings for the alarm action at an alarm occurrence, the alarm occurrence notification, and the VMD area settings can be configured on this page. The "Alarm setup" page has 3 tabs; the [Alarm] tab, the [VMD area] tab and the [Notification] ta[...]

44 Configure the settings relating to the camera action at an alarm occurrence Click the [Alarm] tab on the "Alarm setup" page. ( ☞ page 15) ■ Camera motion on alarm The settings relating to the camera action at an alarm occurrence can be configured in this section. Refer to pages 43, 46 and 47 for further information about the settin[...]

45 Auto track: When a VMD alarm is detected, the cam- era will move to the home position and start the auto tracking. Default: OFF [Command alarm] Select an action to be taken when a command alarm is detected from the following. OFF: Does not take any action even when a command alarm is detected. 1-64: When the registered preset position is selecte[...]

46 Configure the settings relating to the alarm image Click the [Alarm] tab on the "Alarm setup" page. ( ☞ page 15) ■ Alarm image setup The settings relating to the alarm image to be transmitted to an FTP server can be configured in this section. The alarm image will be transmitted to an FTP server. To transmit alarm images to an FTP [...]

47 Configure the settings relating to the alarm out connector Click the [Alarm] tab on the "Alarm setup" page. ( ☞ page 15) ■ Alarm output terminal setup The settings relating to the alarm out connector can be configured in this section. The settings for the alarm output terminal can be configured only when "Alarm output" is[...]

48 Set the VMD areas [VMD area] Click the [VMD area] tab on the "Alarm setup" page. ( ☞ page 15) The video motion detection areas can be set on this page. The VMD areas can be set for each preset position (up to 64 areas). When motion is detected in the set area, the alarm action will be performed. The camera can be configured to take a[...]

Configure to detect motion in areas without the preset positions Configure whether or not to detect motion when the camera is not at the preset position by setting the detection sen- sitivity. The sensitivity can be set by configuring "VMD area setting except Preset position". When determining whether to detect motion even when the camera[...]

50 Step 1 Select a preset position number to which the VMD area is to be set from "Preset position select" of "VMD area setting for Preset position". Step 2 Click the [Setup] button. → The VMD area setup window for the selected preset position number will be displayed. Step 3 Set the video motion detection area by dragging the[...]

51 Step 5 Select the detection sensitivity from the following. The selected detection sensitivity will be applied to all the VMD areas. High/Middle/Low Default: Middle Step 6 Click the [SET] button after completing the settings. Important: The setting will not be applied unless the [SET] but- ton is clicked. Delete the VMD area set for the designat[...]

52 Configure the settings relating to the mail notification [Notification] Click the [Notification] tab on the "Alarm setup" page. ( ☞ page 15) ■ E-mail notification setup The settings relating to the alarm mail can be configured in this section. To provide notification of an alarm occur- rence by e-mail, it is necessary to configure [...]

53 Configure the settings relating to Panasonic alarm protocol Click the [Notification] tab on the "Alarm setup" page. ( ☞ page 15) ■ Panasonic alarm protocol setup The settings relating to Panasonic alarm protocol can be configured in this section. [Panasonic alarm protocol] Select "ON" or "OFF" to determine wheth[...]

54 Configure the settings relating to the authentication [Authentication setup] The settings relating to the authentication such as users and PCs restrictions for accessing the camera can be con- figured on this page. The "Authentication setup" page has 2 tabs of the [User] tab and the [Host] tab. Configure the settings relating to the us[...]

55 Configure the settings relating to the host authentication [Host] Click the [Host] tab on the "Authentication setup" page. ( ☞ page 15) The settings to restrict PCs (IP address) from accessing the camera can be configured on this page. [Host authentication] Select "ON" or "OFF" to determine whether or not to authe[...]

56 Configure the settings of the servers [Server setup] The settings relating to the mail server and the FTP server can be configured on this page. The "Server setup" page has 2 tabs; the [Mail] tab and the [FTP] tab. Configure the settings relating to the mail server [Mail] Click the [Mail] tab on the "Server setup" page. ( ☞[...]

57 Configure the settings relating to the FTP server [FTP] Click the [FTP] tab on the "Server setup" page. ( ☞ page 15) The settings relating to the FTP server used to transmit the alarm images can be configured on this page. [FTP server address] Enter the IP address or the host name of the FTP serv- er. Number of characters for the FTP[...]

58 Configuring the network settings [Network setup] The network settings and the settings relating to DDNS (Dynamic DNS) and SNMP (Simple Network management Protocol) can be configured on this page. The "Network setup" page has 4 tabs; the [Network] tab, the [DDNS] tab, the [SNMP] tab and the [FTP] tab. Configure the network settings [Net[...]

59 [Default gateway] When not using the DHCP function, enter the default gateway of the camera. Default: 192.168.0.1 <Unavailable IP addresses for the default gate- way> 0.*.*.* *.*.*.0 255.*.*.* *.*.*.255 127.0.0.1 Class D addresses (224.0.0.0 - 239.255.255.255) Class E addresses (240.0.0.0 - 255.255.255.255) Note: These IP addresses for the[...]

60 Notes: • The port forwarding function changes a global IP address to a private IP address, and "Static IP masquerade" and "Network Address Translation (NAT)" have this function. This function is to be set in a router. • To access the camera via the Internet by connecting the camera to a broadband router, it is necessary t[...]

61 [DDNS] Select "ON" or "OFF" to determine whether or not to use the DDNS function. Default: OFF [Host name] Enter the host name to be used. Number of characters for the host name: 1 - 64 char- acters [User name] Enter the user name (login name) to access the DDNS server. Number of characters for the user name: 1 - 32 char- act[...]

62 Configure the settings relating to SNMP [SNMP] Click the [SNMP] tab on the "Network setup" page. ( ☞ page 15) The settings relating to SNMP can be configured on this page. It is possible to check the status of the camera by connecting to the SNMP manager. When using the SNMP function, contact the network administrator. [Community nam[...]

63 Configure the settings relating to the FTP periodic transmission [FTP] Click the [FTP] tab on the "Server setup" page. ( ☞ page 15) ■ FTP periodic transmission The settings relating to the periodic transmission of images to an FTP server can be configured in this section. To transmit images to an FTP server periodically, it is nece[...]

64 Configure the schedule settings of the FTP periodic transmission Click the [FTP] tab on the "Server setup" page. ( ☞ page 15) ■ Schedule setup The schedule settings of the FTP periodic transmission can be configured in this section. Refer to page 63 for further information about the settings relating to the FTP periodic transmissio[...]

65 How to delete the set schedule Step 1 Uncheck the check box of the set day of the week. Step 2 Click the [SET] button after completing the settings. → The result will be displayed at the bottom of the win- dow.[...]

66 Maintenance of the camera [Maintenance] System log check, firmware upgrade, and initialization of the setup menu can be performed on this page. The "Maintenance" page has 3 tabs; the [System log] tab, the [Upgrade] tab and the [Initialization] tab. Check the system log [System log] Click the [System log] tab of the "Maintenance&qu[...]

67 Upgrade the firmware [Upgrade] Click the [Upgrade] tab of the "Maintenance" page. ( ☞ page 15) The current firmware can be checked and upgraded to the latest version on this page. Contact the dealer for further information about the firmware upgrade. [Model No.], [MAC address], [Serial number], [Firmware version], [IPL version], [Ins[...]

68 Initialize/restart the camera [Initialization] Click the [Initialization] tab of the "Maintenance" page. ( ☞ page 15) Initialization of the settings and data of the camera and restarting of the camera can be performed on this page. [Initialize camera setup data (Except network and preset setup data)] Click the [Execute] button to res[...]

69 About the displayed system log Error indications relating to SMTP Category POP3 server error SMTP server error Internal error Authentication error Failed to find POP3 server SMTP authentication error Other error Failed to resolve mail server address from DNS Failed to find SMTP server Entered user name or password may be incorrect. Check if the [...]

70 C ategory Connection error Connection error Time adjustment synchronizing with NTP succeeded. Internal error Internal error No response from the server No response from the server Auto time adjustment succeeded. Other error Password error for the entered user name IP address updated error Other error • The designated IP address of the DDNS may[...]

71 • Are you accessing the wrong IP address? Check the connection as follows: With the Windows command prompt, > ping "IP address of the camera" When the WV-NS202 replies, the camera is function- ing normally. If not, proceed either of the following. • Restart the camera and change the IP address by using the Panasonic IP setup sof[...]

6 • Is the focus adjusted correctly? Adjust the focus correctly by clicking the focus but- tons. • Is there dust or dirt on the lens? Check if there is dust or dirt on the lens. • Is "Allow" selected for "FTP access" on the [Network] tab of "Network setup" page? If not, select "Allow". • Is the power [...]

73 • Is any part of the camera worn out? When the camera does not move to the exact position frequently, the driving parts may be worn out. Contact the dealer for assistance. • When the camera position is moved from the preset position after turning on the power of the camera, execute the refresh position function from the [Initialization] tab [...]

• Isn ’ t the SD memory card out of order? There are limited times to overwrite on an SD memory card. When frequently overwritten, it may be at the end of product life. It is recommended to replace the SD memory card. • Is the viewer software installed on the PC? Confirm that the viewer software "Network Camera View3" is installed. [...]

• Are images displayed on a full screen? Audio will not be transmitted when displaying images on a full screen. • Press the [F5] key on the keyboard of the PC or click the [Live] button. 7 5 • Is the viewer software installed on the PC? Confirm that the viewer software "Network Camera View3" is installed. • Is the OS in use Window[...]

76 • This may occur due to the display adapter and driver combination. When this has occurred, first update the driver of the display adapter to the latest version. If updating the driver does not solve the problem, adjust the hardware acceleration as follows. The following are descriptions for when Microsoft XP Professional SP2 is installed on t[...]

77 • Click "Internet Options" on the Tools menu of Internet Explorer, and then click the [Security] tab. Then, click the [Custom Level … ] button to open the "Security Setting" window. Under "Miscellaneous", select "Enable" for "Allow script-initiated windows without size or position constraints"[...]

78 Director y Structure of Drive B Drive B FTP ALARM 060101 060102 File name 01 0123 06010101 06010102 LOCAL PULL File name 01 06010101 06010102 00000001 00000001 LOG ← Destination where images are to be saved by the SD memory recording function of Panasonic network disk recorder ← Destination where log files are to be saved Image failed to tra[...]

Panasonic Canada Inc. 5770 Ambler Drive,Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 http://www.panasonic.ca Panasonic Sales Company Division of Panasonic Puerto Rico Inc. San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina P.R. 00985(809)750-4300 Panasonic System Solutions Company, Unit Company of Panasonic Corporation of North A[...]