Patton electronic 2158B manuale d’uso

USER MANUAL MODEL 2158B CopperLINK™ Ethernet Extender SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P ar t# 07M2158B-UM Rev . A Revised 4/8/10 An ISO-9001Cer tified Company This is a Class A device and is intended for use in a light industrial (commercial) environment only . It is not intended nor approved for use in a heavy indu[...]

2 CONTENTS 1.0 Warranty Information ................................................................. 4 1.1 Regulatory Information ................................................................. 4 EMC Directive:.............................................................................. 4 Low-Voltage Direcive (Safety): .........................[...]

3 D Distance Chart, Based on 24 AWG (0.5 MM) .......................... 19[...]

4 1.0 WARRANTY INFORMATION P atton Electronics warrants all Model 2158B components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of the shipment. This warranty is limited to def ects in w orkmanship or materials, and does not cov er customer damage, ab use or [...]

5 of P ar t 15 of FCC rules, which are designed to provide reasonab le pro- tection from such interf erence in a commercial installation. Howe ver , there is no guarantee that interf erence will not occur in a par ticular instal- lation. If the de vice does cause interf erence to radio or tele vision recep- tion, which can be determined by disconne[...]

6 1.6 SAFETY WHEN WORKING WITH ELECTRICITY • This device contains no user serviceable parts. This device can only be repaired by qualified service person- nel. • Do not open the device when the power cord is con- nected. For systems without a power switch and without an external power adapter , line voltages are present within the device when [...]

7 In accordance with the requirements of council direc- tive 2002/96/EC on Waste of Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you sepa- rate this product from other waste and scrap and deliver to the WEEE collection system in your country for recy- cling. This device is NOT intended nor approved for connec- tion to the [...]

8 2.0 GENERAL INFORMATION Thank you f or your purchase of this P atton Electronics product. This product has been thoroughly inspected and tested and is warranted f or one year f or par ts and labor . If any questions or prob lems ar ise during installation or use of this product, contact P atton Electronics T echnical Suppor t at +1 (301) 975-1007[...]

9 Figure 1. T ypical application The pair of 2158B models work together to create a transparent e xtension between two peered Ethernet LANs. Figure 1 shows a typical point-to- point application. 3.0 INSTALLATION T o install the 2158B Ethernet Extender , do the follo wing: 1. Connect the line interf ace between the units (ref er to section 3.1, “C[...]

10 Figure 2. Model 2158B standalone rear panel 3.1 CONNECTING THE TWISTED-PAIR LINE INTERFACE The Model 2158B suppor ts communication between two peer Ethernet LAN sites ov er a distance of up to 3,750 ft (1.1 km) over 24 A WG (0.5 mm) twisted-pair wire. Note Actual distance and link performance ma y vary depending on the environment and type/gauge[...]

11 1. T o function properly , the two Model 2158Bs m ust be connected together using twisted-pair , unconditioned, dr y , metal wire, between 19 (0.9mm) and 26 A WG (0.4mm). Leased circuits that run through signal equalization equipment are not acceptable . 2. The Model 2158B is equipped with an RJ-45 interf ace jack that can be used on the CopperL[...]

12 Figure 4. Model 2158B 10/100Base-T RJ-45 Connector Pinout. 3.3 CONNECTING POWER The Model 2158B does not hav e a power s witch, so it powers up as soon as it is plugged in. An e xternal AC or DC pow er supply is av ailable separately . This connec- tion is made via the barrel jack on the rear panel of the Model 2158B . No configuration is neces[...]

13 Figure 5. Removing protectiv e cov er Figure 6 on page 13 shows the orientation of the DIP switches in the On and Off positions. Figure 6. DIP switch orientation Power Link Ethernet C o p p e r L IN K ™ H i g h S p e e d E t h e r n e t E x t e n d e r 1234 ON Push toggle up for ON position Switch toggle Push toggle down for OFF position 1234 [...]

14 4.2 CONFIGURING DIP SWITCH S1 DIP s witch S1 is where you configure the CopperLINK line . The f ollowing table describes the configuration f or the 2158B. S1-2: Impulse Noise Protection • Fast Mode: Direct data transmission with latency less than 1ms • Interleave Mode: Provides data transmission protection f or up to 250 ms impulse noise w[...]

15 5.2 FRONT PANEL LED STATUS MONITORS The Model 2158B f eatures six front panel LEDs that monitor power , the Ethernet signals, the CopperLINK connection, and the remote/local set- ting. Figure 7 shows the front panel location of each LED . T ab le 2 on page 15 describes the LED functions. Figure 7. Model 2158B front panel T able 2: F ront panel L[...]

16 APPENDIX A SPECIFICATIONS A.1 LAN CONNECTION • T w o shielded RJ-45, 10/100Base-T , IEEE 802.3 Ethernet • CopperLINK Connection: Shielded RJ-45 A.2 TRANSMISSION LINE T w o-wire unconditioned twisted pair. A.3 COPPERLINK DISTANCE • Distance: 3,750 ft (1.1 km) at 10 Mbps upstream/10 Mbps downstream Note Distances depend on selected line rate[...]

17 APPENDIX B MODEL 2158B SERIES F ACTOR Y REPLACEMENT P AR TS AND ACCESSOR IES *Only required with optional UI power supply (08055DCUI) P atton Model # Description Base Models 2158B/E CopperLINK Multi Rate 100 Mbps Ethernet Extender ; No power supply 2158B/E-2PK CopperLINK Multi Rate 100 Mbps Ethernet Extender Kit (2 units preset to local and remo[...]

18 APPENDIX C MODEL 2158B SERIES INTERFACE PIN ASSIGNMENT C.1 10/100BASE-T INTERFACE RJ-45 • Pin 1: TX+ • Pin 2: TX- • Pin 3: RX+ • Pin 6: RX- • Pins 4, 5, 7, 8: no connection C.2 COPPERLINK INTERFACE RJ-45 • Pin 4: RING • Pin 5: TIP • Pins 1, 2, 3, 6, 7, 8: no connection[...]

19 APPENDIX D DISTANCE CHAR T, BASED ON 24 A WG (0.5 MM) Note The actual distance and link performance ma y vary depending on the environment and type/gauge of wire used. Note DS = downstream, US = upstream Line Rate Distance in feet (km) Throughput at Max Distance (bits per second) 10/10 3750 ft (1.1 km) 11,538,240 (DS) 11,544,288 (US)[...]

20 Cop yright © 2010. P atton Electronics Company All Rights Reser ved.[...]