Pelco Not ICS110-CW manuale d’uso

INST ALLA TION ICS110-CW Series Camclosure ® Integrated Camera System Wide Dynamic Range (WDR) C3406M-D (1/07)[...]

[...]

C3406M-D (1/07) 3 Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Models . . . . . . .[...]

4 C3406M-D (1/07) List of Illustrations 1 Package Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 Basic Surface Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 4S Electrical Box Installation . . . . . . . . .[...]

C3406M-D (1/07) 5 Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE Thi[...]

6 C3406M-D (1/07) Description The ICS110-CW Series Camclosure ® integrated camera system combines an environmental cover, back box, camera, lens, and lower dome into a small, high-security system that is quick and easy to install. The system is perfect for a variety of indoor and outdoor applications and its versatile design allows for multiple mo[...]

C3406M-D (1/07) 7 Figure 1. Package Components COVER AND BACK BOX (1) CAMERA MODULE (1) TRIM RING, DOME LINER, AND CLEAR BUBBLE (1) TRIM RING AND SMOKED BUBBLE (1) < OR > 1/8-INCH HOLLOW SCREWDRIVER BIT (1) BLACK PLUG (1) SHOWN ACTUAL SIZE SHIPPING BOX 8-32 X 0.75-INCH PHILLIPS P AN HEAD SCREWS (2) 8-32 X 0.375-INCH PHILLIPS P AN HEAD SCREWS [...]

8 C3406M-D (1/07) Cover and Back Box Installation The ICS110-CW Series Camclosure integrated camera system mounts only to a surface. It can be wired through the cover into a surface, electrical box, or plaster ring. Y ou can also wire it through a side conduit. UNSHIELDED T WISTED PAIR (UTP) V IDEO The ICS110-CW Series offers support for unshielded[...]

C3406M-D (1/07) 9 8. Reinstall the back box inside the cover. For vandal-resistant installations, rotate the back box to position the conduit plug opposite the notch on the side of the cover. Use the two 8-32 x 0.375-inch Phillips pan head screws and washers (removed earlier) to secure the back box to the cover . Figure 2. Basic Surface Installatio[...]

10 C3406M-D (1/07) 6. Connect the power wires. AC operation only: If you are wiring more than one Camclosure integrated camera system to the same transformer , connect one side of the transformer to the red wire on all units, and connect the other side of the transformer to the black wire on all units. Failure to connect all of the units the same w[...]

C3406M-D (1/07) 11 404 PLASTER RING INSTALLATION NOTE: Y ou should install the camera module into the back box before installing the back box into the cover . When installing the back box into the cover, rotate the camera module to access the mounting holes. Refer to Camera Module on page 14 for more information. 1. Remove the two 8-32 x 0.375- inc[...]

12 C3406M-D (1/07) 5. Reinstall the back box inside the cover. For vandal-resistant installations, rotate the back box to position the conduit plug opposite the notch on the side of the cover. Use the two 8-32 x 0.375-inch Phillips pan head screws and washers (removed earlier) to secure the back box to the cover . Figure 4. 404 Plaster Ring Install[...]

C3406M-D (1/07) 13 7. Install a 0.75-inch (1.91 cm) threaded conduit connector (not supplied) into the conduit hole in the back box. Figure 5. Side Conduit Installation 8. Connect the video cable/wires: BNC: Connect the BNC connector from the unit to a mating BNC connector. T wisted Pair (UTP): Blue wire = Video + Gray wire = Video - 9. Connect the[...]

14 C3406M-D (1/07) Camera Module The ICS110-CW Series Camclosure camera module includes the camera, camera bracket, and heater board. T o perform most camera adjustments, you must remove the module from the back box. Use the following instructions to remove and reinstall the camera module. MODULE REMOVAL T o remove the camera module from the back b[...]

C3406M-D (1/07) 15 2. Unplug the camera (10-pin), heater board (four-pin), and service (three-pin) connectors from the back box (refer to Figure 7). Figure 7. Back Box Connectors CAMERA CONNECTOR HEA TER BOARD CONNECTOR SERVICE CONNECTOR[...]

16 C3406M-D (1/07) CAMERA ORIENTATION At the factory , the camera module is confi gured for ceiling mounting. For wall mounting, you must change the camera orientation or the video image will be upside down. T o change the camera orientation (refer to Figure 8): 1. Remove the camera module from the back box if necessary . 2. Remove the tilt adjust[...]

C3406M-D (1/07) 17 Camera Adjustments T o perform the following camera adjustments, make sure to plug in the camera and service connectors. Y ou may have to remove the camera module from the back box. Connect a monitor . Then turn on power to the camera and monitor. T o use the service connector, refer to Service Connector on page 22. T o adjust th[...]

18 C3406M-D (1/07) SWITCH SETTINGS Locate the DIP switch (refer to Figure 10). Then set the switches for your installation. Figure 10. DIP Switch SW1: Video Format Set to ON for NTSC. Set to OFF for PAL. The default is ON. SW2: Line Sync Set to ON to use AC line lock. Set to OFF for internal line sync. The default is ON. SW3: Interlaced Scanning/Pr[...]

C3406M-D (1/07) 19 Extended dynamic range: Use for extremely high dynamic installations, for example, doorways, entrances, and exits. This profi le offers the maximum wide dynamic range. Fluorescent: Use for any installation with fl ickering lighting of any kind. NOTE: If you select the Fluorescent profi le, you should enable AC line lock for be[...]

20 C3406M-D (1/07) Camera Positioning Manually rotate and tilt the camera module to position the camera. Then tighten the tilt screws (axis  in Figure 12). NOTE: Do not over-rotate the module. Excessively turning the module in one direction could result in damage to the wiring. Figure 12. Positioning the Camera     T ilt 140° (20°-[...]

C3406M-D (1/07) 21 Install Dome and T rim Ring 1. Adjust the dome liner if installed (refer to Figure 13): a. Align the screw holes in the trim ring with those in the back box to identify the proper dome liner position. b. Loosen the three Phillips screws located in the trim ring. c. Insert the blade of a standard screwdriver in one of the adjustme[...]

22 C3406M-D (1/07) Service Connector The ICS110-CW Series Camclosure integrated camera system includes a service connector that outputs camera video. Use it at the installation site to set up the fi eld of view and focus the camera. Figure 14. Service Connector Pelco offers two optional items that plug directly into the service connector . Before [...]

C3406M-D (1/07) 23 T o assemble a longer service cable for the Camclosure integrated camera system, purchase the following from a local electronics supply store: 1 2.5 mm monaural headphone plug 1 CPM 88 miniature coaxial connector 1 RG174/U coaxial cable T o assemble the cable: 1. Attach the CPM 88 miniature coaxial connector to one end of the cab[...]

24 C3406M-D (1/07) Specifications CAMERA Imaging Device 1/3-inch imager Dynamic Range 102 dB typical/120 dB maximum Picture Elements Sensor resolution: 742 (H) x 552 (V) Signal System NTSC or PAL Scanning System 2:1 interlace/progressive Synchronization Internal/AC line lock Horizontal Resolution More than 504 TV lines Iris Control Auto Electronic[...]

C3406M-D (1/07) 25 BACKBOX Electrical Input Voltage** 12 VDC or 24 VAC (±10%), autosensing Power Consumption 10 watts or less Video Connector Composite: BNC UTP: T wisted pair General Pan/T ilt Adjustment Manual Pan 360° T ilt 80° (20° to 100° range) Rotation 360° Construction Aluminum with steel camera mounting bracket and polycarbonate dome[...]

26 C3406M-D (1/07)[...]

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repa ir or replace, without charge, any merc ha ndise proved defective in material or wo rkmanship for a period of one year after the date of shipment. Exception s to this warrant y are as noted bel ow: • Five years on FR/F T/FS Series fiber optic pr oducts and TW300 0 Series unshielded [...]

Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO 9001 Australia | Canada | Finland | France | Italy | Russia | Singapore | Spain | Sweden The Netherlands | United Arab Emirates | United Kingdom | United St[...]