Planet Technology POE-2400 manuale d’uso

User’s Manual POE-1200 POE-2400 IEEE 802.3af 12 / 24-Port Power over Ethernet Web Management Injector Hub[...]

2 Trademarks Copyright © PLANET Technology Corp. 2008. Contents subject to which re vision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware w ill wo rk properly in all env ironments and applicatio[...]

3 TABLE OF CONTENTS 1. INTRODUCTION ........................................................................................................................................... 1 1.1 P ACKAGE C ONTENTS .................................................................................................................................. 1 1.2 P RODUCT D E[...]

1 1. INTRODUCTION 1.1 Package Contents Check the contents of your p ackag e for follow ing parts: ● IEEE 802.3af Power over Et hernet Injector Hub x1 ● User’s Manual x1 ● Quick installation guide x1 ● 19” rack mounting kit x1 ● Power cord x 1 ● Rubber feet x 4 If any of these are missing or damaged, pleas e contact your dealer immed[...]

2 Figure 1-1 Pow er over Ethernet Application 1.3 How to Use This Manual This Web Smart Pow er over Ethernet Injector Hub User Manual is structured as follow s:  Section 2, Installation It explains the functions of POE-1200 / POE-2400 and how to phy sically install the POE-1200 / POE-2400.  Section 3 , Management It contains information about[...]

3 1.4 Product Features  Interface  24 / 48-Port RJ-45 STP ¾ 12 / 24-Port “ Da ta inpu t” ¾ 12 / 24-Port “ Data + Pow er output ”  1 10/100Base-TX Management port  PoE  Complies with IEEE 802.3af Pow er over Ethernet Mid-Span PSE  Up to 12/24 IEEE 802.3af devices powered  Support PoE Powe r up to 15.4 w a tts for each [...]

4 1.5 Product Specifications Product POE-1200 POE-2400 Hardw are Specification “Data” Input Ports 12 x RJ-45 STP 24 x RJ-45 STP “Data+Pow er” Output Ports 12 x RJ-45 STP 24 x RJ-45 STP Interface Management Port 1 x RJ-45; 10/100Base-TX, auto-negotiation, auto-MDI LED System: Pow er x 1 Per PoE Port: PoE in Use x 1 Netw ork Cable • 10Base-[...]

5 2. INSTALLATION This section describes the har dware features and installation of these PoE Injector Hub on the desktop or rack mount. For easier management and control of the PoE Inje ctor Hub familiarize y ourself w ith its display indicators, and ports. Front panel illustrations in this chapter display the unit LED indica tors. Before deploy t[...]

6 The following is the summary table of Reset button functions : Reset Button Pressed and Released Function About 1 second Reboot the PoE Injector Hub Until the SYS LED lit off Reset the PoE Injector Hub to Factory Default configuration. The PoE Injector Hub will reboot and load the default IP settings as below: 。 Default Passw ord: admin 。 Def[...]

7 Figure 2-4 POE-2400 Rear Panel Pow er Notice: 1. The device is a power-required devic e, it means, it will not w ork t ill it is powered. If y our netwo rks should active all the time, please consider using U PS (Uninterrupted Power Supply ) for your device. It will prevent y ou from network data loss or network dow ntime. 2. In some area, instal[...]

8 Step5: Supply power to the PoE Injector Hub. A. Connect one end of the power cable to the PoE Injector Hub. B. Connect the power plug of the pow er cable to a standard w all outlet. When the PoE Injector Hub receives power, the Pow er LED should remain solid Green. 2.2.2 Rack Mounting To install the PoE Injector Hub in a 19-inch standard rack, fo[...]

9 Figure 2-6 Mounting thePoE Injector Hub in a Rack Step6: Proceeds with the steps 4 and steps 5 of session 2.2.1 Desktop Installation to connect the network cabling and supply pow er to your PoE Injector Hub. 2.2.3 Network Application Installation The PoE Injector Hub is not equipment with data sw itching function betw een data port s. T o inject [...]

10 Figure 2-7 Netw ork application installation The PoE Injector Hub supports Data passive mode, that is , even the PoE Injector Hub is manual power off, the data between “ D AT A” port and “ DAT A+ P o E ” port can still be transmi tted without data loss. The POE-1200 / POE-2400 Mid-Span Injector Hub doesn’t support Gigabit data rate. Th[...]

11 3 MANAGEMENT This chapter describes how to manage the W eb Smart PoE Injector Hub. Topics include: - Overv iew - Management method - Logging on to the Web Smart PoE injector Hub 3.1 Overview The Web Smart PoE injector Hub provides a user-friendly, W eb interface. Using this inte rface, you can perform various device configuration and managem ent[...]

12 Figure 3-1 Web Management over Ethernet 2. When the follow ing login screen appears, please enter the default username "admin" and password “admin” (or the password y ou have changed via console) to login the ma in screen of PoE Injector Hub. The login screen in Figure 3-12 appears. Default IP Address: 192.168.0.100 Default Account[...]

13 3.3.2 PLANET Smart Discovery Utility For easily list the PoE Injector Hub in your Ethernet envir onment, the Planet Smart Discovery Utility from user’s manual CD-ROM is an ideal solution. The following install instructions guiding you for run the Planet Smart Discovery Utility. 1. Deposit the Planet Smart Discove ry Utility in administrator PC[...]

14 4. This utility show all necessary info rmation from the devices, such as MAC Address, Device Name, firmw are version, Device IP Subnet address, also can assign new passw ord, IP Subnet address and description for the devices. 5. After setup completed, press “Update Dev ice” , “Update Multi” or “Update A ll” button to take affect. Th[...]

15 4 WEB CONFIGURATION The PoE Injector Hub provide Web interface for PoE smart function configuration and make the PoE Injector Hub operate more effectively - They can be configured through the Web Browser. A netw ork administr ator can manage and monitor the PoE Injector Hub from the local LAN. This section indicates how to configure the PoE Inje[...]

16 4.2 Web Panel At the top of the Web management page, the active panel displays the lin k status of management port and PoE ports. Figure 4-2 Main menu screen  Green lit is the netw ork data send or receiver,  Orange lit is the PoE in use. 4.3 System The System function allows view ing system information, IP Configuration and Passw ord Sett[...]

17 4.3.1 System Information The System information allows view ing system MAC Address, Software Version, Hardw are Version, IP Address, Subnet Mask and Gateway .. As showed in Figure 4.4 Figure 4-4 System Information screen The page includes the following fields: Object Description Specifies the PoE Injector Hub MAC address. MAC A d d ress The curr[...]

18 The page includes the follo wing configurable data: Object Description Choose what the PoE Injector Hub should do follow ing pow er-up: transmit a DHCP request, or manual setting (Disable). DHCP Client The DHCP client function only works if y ou haven' t assigned a static IP address that different than the PoE Injector Hub default IP. Once [...]

19 4.4 PoE  Pow er Management: In a power over Ethernet sy stem, operati ng pow er is applied from a power source (PSU-power supply unit) over the LAN infrastructure to powered devices (PDs), w hich are connected to ports. Under some conditions, the total output pow er required by PDs can exceed the maximum available power pr ovided by the PSU. [...]

20 PoE Function Can enable or disable the PoE function. Priority Set port priority for the POE pow er management It can choose the “port priority” , value is “1~4” . High priority is “1” . Device class Class 0 is the default for PDs. However, to improve power managem ent at the PSE, the PD may opt to provide a signature for Class 1 to 3[...]

21 4.5 Tools This function displays the PoE Injector Hub tools; include “ System Reboot ”, “ Configuration Se tting ”, “ A lert trap Configuration ” and “Firmware upgrade” . As showed in Figure 4-8 . Figure 4-8 T ools screen Object Description System Reboot Allow to reboot the PoE Injector Hub . Explained in section 4.5.1. Configura[...]

22 4.5.2 Configuration Setting This function allows backup and restore the current configuration of PoE Injector H ub, or reset the converter to factory default. The description of the three it ems as follow and screen in Figure 4-10 appears. ■ Backup - To backup/save the current configuration to the storage block on this converter. ■ Restore ?[...]

23 ■ Restore The PoE Injector Hub will restore to previ ous backup/saved confi guration w hile the “ Restore ” button be pressed. And please note that once the Rest ore button be pressed, Web interface will di sconnected for a while. Reload the Web brow ser to re-login the system. Figure 4-13 Configuration restore screen ■ Factory Reset The[...]

24 4.5.3 Alert Trap Configuration This function displays the PoE Injector Hub alert trap configuration; include “enable” or “disable” the trap mode and set the alert IP address. As showed in Figure 4-16. Figure 4.16 Alert T rap Configuration screen Object Description Trap mode Can choose enable/disable to get the trap A lert IP address Asig[...]

25 4.5.4 Firmware Upgrade This section provides firmware upgrade of PoE Injector Hub, after choose this function and the following screen appears in Figure 4-17 . Please press “Update” button to continue following firmw are upgrade process. Figure 4-17 Firmware Upgrade screen Please w ait for tw o seconds and the page will show to next firmware[...]

26 Figure 4-19 Firmware Upgrade screen Do not power off the PoE Injector H ub until the update progress is complete. Do not quit the Firmware U pgrade page w ithout press the “Upgrade” button - after the image is loaded. Or the system w on’t apply the new fi rmw are. Users have to r epeat the firmware upgrade processes again. 4.6 Logout Press[...]

27 Figure 4-21 Login screen[...]

28 5. POWER OVER ETHERNET OVERVIEW What is PoE? Based on the global standard IEEE 802.3af, PoE is a technology for w ired Ethernet, the most w idely installed local area network technology adopted today. PoE allow s the electrical pow er necessary for the operat ion of each end-device to be carried by data cables rather than by s eparate pow er cor[...]

29 The data pairs are used. Since Ethernet pairs are transformer c oupled at each end, it is possi ble to apply DC power to the center tap of the isolat ion transformer without upsetting t he data transfer. In this mode of operation the pair on pins 3 and 6 and the pair on pins 1 and 2 can be of either polarity. Figure 3 - Pow er Supplied over the [...]

30 6. THE POE PROVISION PROCESS While adding PoE support to networked devices is relatively pai nless, it should be realized that pow er cannot simply be transferred over existing CAT-5 cables. Wi thout proper preparati on, doing so may result in dam age to devices that are not designed to support provision of power over their netw ork interfaces. [...]

31 6.3 Start-up Once line detection and optional classification stages are complet ed, the PSE must switch from low voltage to its full voltage capacity (44-57 Volts) over a minimal amount of time (above 15 microseconds). A gradual startup is required, as a sudden rise in volt age (reaching high frequencies) w oul d introduce noise on the data line[...]

32 7 TROUBLESHOOTING This chapter contains information to help you solve problems. If the Device is not functioning properly, make sure the Ethernet Injector Hub was set up accord ing to instructions in this manual. What is the pow er output of each IEEE 802.af PoE port? Solution: Each PoE port supports 48VDC, 350mA , max 15.4 w a tts pow er output[...]

33 APPENDIX A A.1 MDI Settings The Medium-Dependant Interface (MDI or RJ-45) serves as t he data/power interface betw een Ethernet elements. As such, it has two optional connection methods, to carry the power. nam ed Alternative A & B. Table 1 details the two pow er feeding alternatives. Pin A lternative A Alternative B 1 Vport Negative 2 Vport[...]

34 A.3 DATA OUT PoE Injector RJ-45 Port Pin Assignments PIN NO RJ-45 SIGNA L ASSIGNMENT 1 Output Transmit Data + 2 Output Transmit Data - 3 Receive Data + 4 Power + 5 Power + 6 Receive Data - 7 Power - 8 Power -  A.4 RJ-45 pin assignment of non-802.3af standard PD w ith PD w ith Mid-Spain POE Mid-Span RJ-45 assignment Pin out of Cisco non-802.3a[...]

35 Before you pow ered PD, please check the RJ-45 connector pin assignment follow IEEE 802. 3af standard, otherw ise you may need change one of the RJ-45 connector pin assi gnment, w hich attacted with the UTP cable.[...]

36 APPENDIX B B.1 Power over Ethernet Compatibility test No. PDs PoE Output Note 1 [PLANET POE-151S-12V] + [PLANET ICA-500] 9.6W 2 [PLANET POE-151S-12V] + PLANET ICA310 6.4W Standby 3 [PLANET POE-152S-12V] + [PLANET ICA-500] 7.3W 4 [PLANET POE-151S-5V] + [Sparklan A+G AP] 5.7W~7.6W 5 [PLANET POE-151S-12] + IR338 5.1W LED Off 6 [PLANET POE-151S-12] [...]

P L A N E T TECH N O LOG Y CO R POR A T ION e -m a i l: s a l e s @ p l a n e t.c o m . tw h t t p : / / ww w . p l a n et.c o m . tw 1 1 F , No . 9 6 , M i n Ch u an Roa d, H s in T ien , T aip e i, T a i wa n, R . O. C . T e l : 8 8 6 - 2 - 2 21 9 -95 18 F a x : 8 8 6 - 2 - 2 2 1 9-95 2 8 E C D e claration o f Conformity F o r t he f oll ow in g [...]

P L A N E T TECH N O LOG Y CO R POR A T ION e -m a i l: s a l e s @ p l a n e t.c o m . tw h t t p : / / ww w . p l a n et.c o m . tw 1 1 F , No . 9 6 , M i n Ch u an Roa d, H s in T ien , T aip e i, T a i wa n, R . O. C . T e l : 8 8 6 - 2 - 2 21 9 -95 18 F a x : 8 8 6 - 2 - 2 2 1 9-95 2 8 E C D e claration o f Conformity F o r t he f oll ow in g [...]