POSIFLEX Business Machines TM-8315 manuale d’uso

Part 1 I. FEATURES • LM/TM-8115 is a stand along LCD monitor for industrial and commercial use. • TM-8315 is a second display which sui t for Posiflex POS Terminals with Gen.5 base stand. • Application covers POS, Factory A utomation etc. • High quality 15” TFT LCD panel w ith scaling function for full screen display . • TM-8315 support[...]

Part 2 II. CARTON CONTENTS 1. To uch Monitor (Main unit + Adjustable base sta nd assembly) 2. User’s Manual 3. VGA cable 4. USB cab le 5. Power adapto r & po wer cord(For TM /LM-8115) (For T M-8315, please refer to the terminals manual to sup port po wer from VGA cable) 6. Posiflex Pro duct Information CDR OM 7. Option RS232 cable III. INSTAL[...]

Part 3 TM-8315 After open the carton, ple ase take out the monitor carefull y. Please place the monitor’s bracket to the ba ck of base stand a nd fasten the sc rews which circled on the upper picture. IV. PARTS IDENTIFICATION A. FRONT VIEW TM/LM-8115 TM-8315 Display Screen + Touch Panel Main Unit Adjustable Base Assembly Option SD-400Z Logo + Po [...]

Part 4 B. SIDE VIEWS TM/LM-8115 TM-8315 Lock/release lever Push in this direction to adjust the tilt angle of the display panel Control button area Lock/release butto n to detach the main unit NXT button “+” button OSD button “-“ button Power switch Control button area Bracket to fix on the base stand NXT button “+” button OSD button ?[...]

Part 5 V. INPUT / OUTPUT PORTS VI. AVAILABLE OPTION ITEMS 1. Side mount upgrade kit SD-40 0Z or KP -300 2. Wall mount kit (WB-600 0V-B) VII. HARDWARE INSTALLATION A. Option Side M ount Upgrade K it When a side-mount upgrade kit option such as SD-400Z is ordered with the LM-8115 / TM-81 15 / TM -8315 m onitor, this option is alre ady installed in th[...]

Part 6 Refer to the bo ttom vie w picture o f the separated base, pass a ll cable through the cable tunnel as hollow arro wed with cab le tie fro m the cable passage to the main unit i n left p icture. Hook the main unit back onto base stand asse mbly by matching the matching pegs to ro und part of matching holes and slide them do wn to slot part t[...]

Part 7 C. Option Wal l Mount Kit For TM/LM-8115 Select a flat surface on wall of adeq uate strength a nd with p roper ventilation and space condition. Please use the right material to hold this monitor according to the wall mater ial (Dryw all, concrete, solid wood, etc) . Cons ult with your c ontractor if it is necessary . Please fix WB-6000 V-B a[...]

Part 8 clicking on t he right button of a m ouse, touching any point on the s creen surface after touchin g the right-clic k sticky butto n results as a click on t he right button of the mouse at t hat point. C. POSIFLEX U SB TOUCH MA NAGER a. USB touch manage r Once t he U SB control program is installed, the user can utilize it to calibrate the t[...]

Part 9 box is checked.  Touch M ode Setting – Only one o f the three radio buttons can be selected. T he mouse emulation refers to the drag a nd dro p function.  OK – T his button accepts a ll param eters set and closes the utility window.  Apply – T his button accep ts all p arameters set and remains in t he utility windo w.  Can[...]

Part 10 full screen display of Wi ndo ws DOS box should be avoide d. E. APPLICATION L IMITAT ION The USB touch is not ap plicab le for OS other than Wi ndows as USB mou se is not supported in DO S environment. The USB touch i s also n ot applicable when the monitor is used to be the extended scree n i n multiple m onitor application. In using t he [...]

Part 11 B. OSD functions Press “OSD” b utton with a n ormal di splay o n the screen t o activate t he OS D functions (On Scree n Displa y adjustment). T he OSD wind o w will p op up o n the screen. On top part of this windo w is a Posiflex lo go with the OSD firmware versio n indicated to its lo wer right. Below this a rea is a ro w of icons fo[...]

Part 12 exits the OSD windo w leaving 2 icons b elow at center o f the scree n. Press “NXT” button to switch the selection. Pr ess “OSD” button to make the choice. “ACCEPT”: Accept the adjust ment setting. “REJECT”: Decli ne the adjust ment setting and return to previous setting. “AUTO RG B RE SET”: Upon an “OSD” button pre [...]

Part 13 horizontal size, phase, horizontal p osition, vertical positio n and exit. “AUTO GEOM ETRY ADJUST”: Upon an “OSD” button p ress on this icon the monitor will perform an automatic geometry adjustment and exits t he OSD window lea ving 2 icons below at center o f the screen. Press “NXT” button to switch the selection. Pr ess “OS[...]

Part 14 OSD horizontal posit ion, OSD vertical p osition and exit. “OSD TIM E”: When this ite m is selected, there will be only the O SD ti me icon with an ad justment indication bar under it bet ween the main m enu area and the video signal mode. P ress “+” or “-” button to adjust the waiting time for OSD operation before OSD terminati[...]

Part 15 XI. SUPPORTED DISPLAY MODES For video signals be yond the supporte d d isplay modes, there will be a message “Out Of Range” o n middle of screen. Ma ximum s upported colo r depth is 24 bits or 16 .2 M colors. Suppor ted display modes are as in the table: Display Resolution Refresh Rate (Hz) Horizontal Frequenc y (KHz) 640*400 70 31.5 60[...]