Quatech QSCLP-100 manuale d’uso

QS C LP-100 Four Channel Low Profile RS-232 Asynchronous Communications Adapte r for PCI bus User's Manual QUATECH, INC. TEL: (330) 434-3154 662 Wolf Ledges Parkway FAX: (330) 434-1409 Akron, Ohio 44311 http: //www.quatech.com[...]

1 General Information The Quatech, Inc. QSCLP-100 provides four RS-232 asynchronous serial communication interfaces for Low Profile I BM-compatible personal computer systems using the PCI expansion bus . The QSCLP-100 uses Quatech's new Enhanced Serial Adapter design. Legacy serial port data rates are limited to a maximum of 115,200 bits per s[...]

2 Hardware Configuration The QSCLP-100 is automatically configured at boot time by the computer's BIOS or operating system. There are no required switches or jumpers to set for installation. This chapter lists a number of optional jumper settings that control various hardware features. Jumpers J 2 -J 5 are grouped together at the end of the bo[...]

These jumpers force an increase of the UART input clock frequency by a factor of two, four, or eight. This feature can allow legacy software to use baud rates above 115,200 bits per second. It is also useful if the serial port device driver does not directly support setting the higher baud rates through the Options Register (see page 0 ). If one of[...]

3 Hardware Installation 1. Turn off the power of the computer system in which the QSCLP-100 is to be installed. 2. Remove the system cover according to the instructions provided by the computer manufacturer. 3. Make any desired optional jumper setting changes. 4. Install the QSCLP-100 in any empty PCI expansion slot. The board should be secured by [...]

(This page intentionally blank.) QSCLP-100 User's Manual 5[...]

4 Address Map and Special Registers This chapter explains how the four UARTs and special registers are addressed, as well as the layout of those registers. This material will be of interest to programmers writing driver software for the QSCLP-100. 4 . 1 Base Address and Interrupt Level (IRQ ) The base address and IRQ used by the QSCLP-100 are deter[...]

4 . 2 Enabling the Special Registers The QSCLP-100 contains two unique registers, an Interrupt Status Register and an Options Register. These registers are enabled when the SPAD jumper (J6) is removed (factory default). They replace the UART Scratchpad Register on accesses to register address 7. The Interrupt Status Register and Options Register ar[...]

4 . 4 Options Register The Options Register allows software to identify the QSCLP-100 as a Quatech Enhanced Serial Adapter. It also allows software to set the UART clock rate multiplier. Figure 8 shows the structure of the Options Register. The powerup default of the Options Register is all bits zero. Clock rate multiplier bit 0 RR0 0 Clock rate mu[...]

4 . 4 . 2 Clock Rate Multiplier A standard RS-232 serial port operates at a clock speed of 1.8432 MHz. In order to achieve higher data rates, Quatech Enhanced Serial Adapters can operate at two times, four times or even eight times this standard clock speed. This is controlled by the clock rate multiplier bits in the Options Register. Software can [...]

5 Windows Configuration s 5 . 1 Windows Mille nnium 1. After inserting the QSCLP - 100 for the first time the "Add New Hardware Wizard" will begin. Select "Search for the best driver for your device.". Check the "Removable media" and "Specify location" box. Click the "Next" button. 3. Window will lo[...]

5 . 2 Windows 2000 1. After inserting a QSCLP-100 for the first time, the "Add New Hardware Wizard will appear at start up. C lick the "OK" button. 2. The following dialog box insert the Quatech COM CD (shipped with the device). Click the "OK" button. 4. The following dialog box will display the appropriate INF file on the [...]

5 . 3 Windows 98 1. After inserting a QSCLP-100 for the first time, the "Add New Hardware Wizard will appear at start up. C l ick the "Next" button. 2. Select "Search for the best driver for you device". Click the "Next" button. 3. On the next dialog, select the " CD-ROM DRIVE " check box. Insert the Qua[...]

4. The following dialog box will display the appropriate INF file on the diskette in drive. Click the "Next" button. 5. Window will copy the INF file from the diskette and display a final dialog indic ation that the process is complete. Click the "Finish" button. Windows 95 maintains a registry of all known hardware installed in[...]

PCI communications adapter before, the dialog box may simply indicate that it has found a "PCI Card." 2. Select the radio button for "Driver from disk provided by hardware manufacturer." Click the " OK " button to continue. 3. An "Install From Disk " dialog box should pop up . Insert the diskette with the Qua[...]

The following instructions provide step-by-step instructions on viewing resources used by the QSCLP-100 in Windows 95 using the "Device Manager" utility. Select Start|Help from within Windows 95 for additional information on this utility. 1. Double click the "System" icon inside the Control Panel folder. This opens up the System[...]

Figure 13 --- Windows 95 Device Manager 6. The QSCLP-100 serial ports are also listed under the group Ports ( COM and LPT). Windows 95 does not assign COM1 - COM4 to ports addressed at nonstandard locations. The QSCLP-100 ports will be enumerated starting with COM5 (or higher) even if lower logical numbers are available. 7. Select any of the Quatec[...]

Figure 14 --- Windows 95 Device Manager 9. Use the Logical COM Port n ames to access the serial ports on your QSCLP-100 through your software applications. Note: The Logical COM Port name is assigned to your ports by Windows 95. This name is required by a Windows 95 application when accessing a particular p QSCLP-100 User's Manual 17[...]

6 Other Operating Systems Device drivers for Windows NT and OS/2 are also available for the QSCLP-100. The board can be used under DOS and other operating systems as well in many circumstances. The software described below can be downloaded from the Quatech web site if it did not come with the board. 6 . 1 Windows NT The Windows NT device driver is[...]

Quatech's "QTPCI" utility supplies the information required when modifying the serial port settings of the applicatio n. This program should be run from real DOS , not in a Windows DOS box. Figure 13 shows the Basic Mode display for the QSCLP-100 after the "Q" key has been pressed. In this example, the QSCLP-100 uses I/O ba[...]

with more details such as the Vendor and Device IDs, PCI Class Code , size of memory and I/O regions, etc. Pressing the "N" key will show similar information for all non-Quatech PCI devices in the system, including those devices integrated on the motherboard. In this example, the "Base addr 0" resource is reserved. For users int[...]

7 External Connections RS-232-C devices are classified by their function as either Data Terminal Equipment (DTE) or Data Communication Equipment (DCE). Generally, data terminal equipment is defined as the communication source and data communication equipment is defined as the device that provides a communication channel between two DTE-type devices[...]

The QSCLP-100 is a DTE device which connects to peripheral equipment through a single female D- 44 connector, or using the adapter cable, four male D- 9 connectors. The standard serial port connections are listed in Figure 17 . 5 30 5 26 5 8 5 19 GND 9 18 9 22 9 25 9 29 RI 1 33 1 37 1 41 1 44 DCD 6 16 6 20 6 23 6 27 DSR 4 17 4 21 4 24 4 28 DTR 8 32[...]

4800 4300 3300 1570 800 115.2 2000 1630 1100 900 330 230.4 1100 900 670 430 100 460.8 470 430 300 100 N/ A 921.6 25% trans time 20% trans time 15% trans time 10% trans time 4% trans time Maximum Load (pF) Data Rate (kbaud ) Note 1: The signal transition time ratio is defined as the percentage of the unit interval or bit time ( the inverse of the da[...]

10 Troubleshooting Listed here are some common problems and frequent causes of those problems. If the information here does not provide a solution, contact Quatech technical support. Any unauthorized repairs or modifications will void the QS C LP-100's warranty. Computer will not boot up. 1. Is the QSCLP-100 properly inserted? Remove the card [...]

WARRANTY INFORMATION Quatech, Inc. warrants the QS C LP-100 to be free of defects for five ( 5 ) year s from the date of purchase. Quatech, Inc. will repair or replace any board that fails to perform under normal operating conditions and in accordance with the procedures outlined in this document during the warranty period. Any damage that results [...]

Declaration of Conformity Manufacturer's Name: Quatech Inc. M anufacturer's Address: 662 Wolf Ledges Parkway Akron, Ohio 44311 (USA) Application of Council Directive: 89/336/EEC Standards to which Conformity is Declared: * EN50081-1 (EN55022 , EN60 555-2 , EN6055 5 -3 ) * EN50082-1 (IEC 801-2, IEC 801-3, & IEC 801-4) Type of Equipment[...]

Table of Contents 28 10 Troubleshooting ........................................ 26 9 Specifications ............................................. 25 8 PCI Resource Map ..................................... 23 7 External Connections .................................. 20 6.3.1 QTPCI.EXE ........................................... 19 6.3 DOS and othe[...]

? 2002 , Quatech, Inc. NOTICE The information contained in this document cannot be reproduced in any form without the written consent of Quatech, Inc. Likewise, any software programs that might accompany this document can be used only in accordance with any license agreement(s) between the purchaser and Quatech, Inc. Quatech, Inc. reserves the righ[...]

8 PCI Resource Map Listed below are the PCI resources used by the QSCLP-100. Such information may be of use to customers writing their own device drivers or other custom software. A detailed description of the QSCLP-100's UARTs is available on the Quatech web site. (all numbers in hex) PCI Vendor ID: 0x135C Quatech, Inc. PCI Device ID: 0x0 170[...]

9 Specifications Bus interface: PCI, 32 -bit bus , 5-volt only IBM - compatible computers Dimensions: approx . 5.0" x 3.7" Serial ports Controller: 16550 with 16-byte FIFOs Interface: One female D- 44 connector Four male D- 9 connectors using adapter cable Trans ceivers : ICL3245CA High-level output: +5V min Low-level output: -5V max, Swi[...]

QSCLP-100 User's Manual Revision 1.00 January 2002 P/N: 940-01 80 -100[...]