Regency L676 manuale d’uso

Unit requires 120V to operate. See “Wiring Diagram” section in manual for more details. Receptacle is included with manual package. T ested by: FPI FIREPLACE PRODUCTS INTERNA TIONAL L TD. 6988 V enture St., Delta, BC Canada, V4G 1H4 918-568f MODELS: L676-NG Natural Gas L676-LP Propane LIBERTY L676 Gas Fireplace FOR YOUR SAFETY What to do if you[...]

Regency ® L676 Direct V ent Gas Fireplace 2 T o the New Owner: Congratulations! Y ou are the owner of a state-of-the-art Gas Fireplace by REGENCY ® . The L676 has been designed to provide you with all the warmth and charm of a wood fi replace at the fl ick of a switch. The model L676 has been approved by W arnock Hersey for both safety and ef?[...]

Regency ® L676 Direct V ent Gas Fireplace 3 T ABLE OF CONTENTS SAFETY LABEL Copy of Safety Decal ..................................................... 4 REQUIREMENTS MA Code - CO Detector (for the State of Massachusetts only) ............................ 5 UNIT DIMENSIONS Unit Dimensions .......................................................... 6[...]

Regency ® L676 Direct V ent Gas Fireplace 4 INST ALLA TION SAFETY LABEL This is a copy of the label that accompanies each L676-NG and L676-LP Zero Clearance Direct V ent Gas Fireplace. We have printed a copy of the contents here for your review . The safety label is located on the right hand side of the unit, visible when the exterior right side b[...]

Regency ® L676 Direct V ent Gas Fireplace 5 INST ALLA TION REQUIREMENTS 5.08: Modifica tions to NFPA-54, Chapter 10 (2) Revise 10.8. 3 by adding the follow ing additiona l requirements: (a) For all side wall hor izontally vented ga s fueled equipment in stalled in every dwellin g, building or structure used in whole or in part for residential pu r[...]

Regency ® L676 Direct V ent Gas Fireplace 6 INST ALLA TION UNIT DIMENSIONS[...]

Regency ® L676 Direct V ent Gas Fireplace 7 INST ALLA TION 12) Installation and any repairs to this appliance should be done by an authorized service person. A professional service person should be called to inspect this appliance annually . Make it a practice to have all of your gas appliances checked annually . 13) Do not slam shut or strike the[...]

Regency ® L676 Direct V ent Gas Fireplace 8 INST ALLA TION INST ALLA TION This includes: 1) Clocking the appliance to ensure the correct fi ring rate (rate noted on label 42,000 (NG) Btu/h, 40,000 (LP) Btu/h) after burning appliance for 15 minutes. 2) If required, adjusting the primary air to ensure that the fl ame does not carbon. First allow t[...]

Regency ® L676 Direct V ent Gas Fireplace 9 INST ALLA TION INST ALLA TION CLEARANCES The clearances listed below are Minimum distances unless otherwise stated: A major cause of chimney related fi res is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this fi replace and vent sys[...]

Regency ® L676 Direct V ent Gas Fireplace 10 INST ALLA TION INST ALLA TION MANTEL CLEARANCES Because of the extreme heat this fi replace emits, the mantel clearances are critical. Combustible mantel clearances from top of front facing are shown in the diagram below . Note: A non-combustible mantel may be installed at a lower height if the framing[...]

Regency ® L676 Direct V ent Gas Fireplace 11 INST ALLA TION INST ALLA TION Diagram 1 1) Frame in the enclosure for the unit with framing material. The framed opening for the assembled kit is 45-7/8" high x 43" wide x 24-1/4" deep (1 143mm x H 1092mm W x 616mm D). See Diagram 1. Also see Diagram 2 for corner installations. IMPORT ANT[...]

Regency ® L676 Direct V ent Gas Fireplace 12 INST ALLA TION INST ALLA TION SIDE NAILING STRIPS The side nailing strips come attached to the unit. There are 3 plates, one on the top and bottom that can be folded out as required. UNIT ASSEMBL Y PRIOR T O INST ALLA TION The T op Facing Support, the Side Nailing Strips and the 2 T op Standoffs must be[...]

Regency ® L676 Direct V ent Gas Fireplace 13 INST ALLA TION V ent restriction is required for certain venting installations, see the diagrams in the "V enting Arrangements" section to determine if they are required for your installation. The V ent Restrictor plate is located on the inside top of the fi rebox. (factory set for NG units) [...]

Regency ® L676 Direct V ent Gas Fireplace 14 INST ALLA TION EXTERIOR VENT TERMINA TION REQUIREMENTS A= Clearance abo ve grade, veranda, porch, deck, or balcony *(min. 12"/30cm) B= Clearance to window o r door that may be ope ned *(12"/30cm ) #(9"/23cm) C= Clearance to permanently closed wind ow *(min. 12"/30cm) D= V ertical cle[...]

Regency ® L676 Direct V ent Gas Fireplace 15 INST ALLA TION 8” dia. Flue pipe 5” dia. flue pipe spring spacer T ermination Cap AstroCap XL TM (Part #946-623/P) V ent Guard - if required* (Part #946-506/P) W all Thimble (Mandatory in all Horizontal T erminations) Vinyl Siding Standoff VENTING ARRANGEMENTS HORIZONT AL TERMINA TION (FLEX) Regency[...]

Regency ® L676 Direct V ent Gas Fireplace 16 INST ALLA TION RIGID PIPE VENTING SYSTEMS BASIC HORIZONT AL & VERTICAL TERMINA TIONS Rigid Pipe V ent Systems offer a complete line of component parts for installation of both horizontal and vertical installations. Many items are offered in decorative black, as well as gal- vanized fi nish. The min[...]

Regency ® L676 Direct V ent Gas Fireplace 17 INST ALLA TION INST ALLA TION Description Simpson Direct V ent Pro ® Simpson Direct V ent GS ® Discontinued Selkirk Direct-T emp™ Metal-Fab ® Sure Seal 6” Pipe Length, Galvanized 58DV A-06 1208 5DT -6 5D6 6” Pipe Length, Black 58DV A-06B 1208B 5DT -6B 5D6B 9” Pipe Length, Galvanized 58DV A-09[...]

Regency ® L676 Direct V ent Gas Fireplace 18 INST ALLA TION L676 & L900 Direct V ent Fireplace IMPORT ANT NOTE • A V ent Guard is required when the AstroCap is installed above grade at 7 feet or lower. • The Simpson Dura-V ent and Selkirk Direct T emp horizontal termination caps cannot be used in any applications. • Only the AstroCap XL [...]

Regency ® L676 Direct V ent Gas Fireplace 19 INST ALLA TION VENTING ARRANGEMENTS ALLOW ABLE HORIZONT AL TERMINA TIONS The diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 90 o two 45 o elbows equal one 90 o elbow). Note: Must use optional rigid pipe adapter (Part# 770-994) when using Rigid Pipe V en[...]

Regency ® L676 Direct V ent Gas Fireplace 20 INST ALLA TION Horizontal V enting with T wo (2) 90 o Elbows Horizontal V enting with Three (3) 90 o Elbows One 90 o elbow = T wo 45 o elbows. Option V H + H1 A) 2' Min. 4' Max. B) 3' Min. 5' Max. C) 4' Min. 6' Max. D) 5' Min. 7' Max. E) 6' Min. 8' Max. [...]

Regency ® L676 Direct V ent Gas Fireplace 21 INST ALLA TION V ertical V enting with T wo (2) 90 o Elbows V ertical V enting with Three (3) 90 o Elbows Option V H V + V1 A) 2' Min. 2' Max. 3' Min. B) 2' Min. 10' Max. 6' Min. C) 3' Min. 6' Max. 4' Min. D) 4' Min. 7' Max. 5' Min. E) 5' [...]

Regency ® L676 Direct V ent Gas Fireplace 22 INST ALLA TION VENTING ARRANGEMENTS ALLOW ABLE VERTICAL TERMINA TIONS • V ent must be supported at offsets. • Firestops are required at each fl oor level and whenever passing through a wall. • Maintain clearances to combustibles as listed in the "Clearances" section. • Refer to "[...]

Regency ® L676 Direct V ent Gas Fireplace 23 INST ALLA TION Diagram 7 Diagram 5 7) Ensure that the pipe clearances to combustible materials are maintained (Diagram 5). Install the termination cap. Note: If installing termination on a vinyl siding covered wall, a vinyl siding standoff or furring strips must be used to ensure that the termination is[...]

Regency ® L676 Direct V ent Gas Fireplace 24 INST ALLA TION 6) Continue to assemble pipe lengths. Note: If an offset is necessary in the attic to avoid obstructions, it is important to support the vent pipe every 3 feet (0.9 meter), to avoid excessive stress on the elbows, and possible separation. W all straps are available for this purpose (Diagr[...]

Regency ® L676 Direct V ent Gas Fireplace 25 INST ALLA TION 4) Separate the 2 halves of the wall thimble and securely fasten the one with the tabs to the outside wall making sure that the tabs are on top and bottom. Fasten the other thimble half to the inside wall. The thimble halves slip inside each other and can be adjusted for 2 x 4 or 2 x 6 wa[...]

Regency ® L676 Direct V ent Gas Fireplace 26 INST ALLA TION IN OUT 13 5 6 4 2 GAS PIPE PRESSURE TESTING The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve d uring any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig. (3.45 kP a) . Disconn[...]

Regency ® L676 Direct V ent Gas Fireplace 27 INST ALLA TION 1) Remove the glass door . 3) Lift up and pull out the heat shield slightly to clear the screwheads and then hang it on the top bracket (located directly above the heat shield). 4) Unplug the power source. 5) Loosen the bottom screw and remove the top screw from the power module. 6) Cut t[...]

Regency ® L676 Direct V ent Gas Fireplace 28 INST ALLA TION CONVERSION KIT #521-969 FROM NG T O LP LP Conversion Kit Contains: Qty . Part # Description 1 910-462 LP Conversion Coil 1 904-573 Cable T ie 1 910-037 LP Pilot Orifi ce 1 904-345 Orifi ce #53 (back) 1 904-241 Orifi ce #56 (front) 1 904-529 Allen Key 1 918-590 LP Conversion Decal 1 908[...]

Regency ® L676 Direct V ent Gas Fireplace 29 INST ALLA TION 13) Lift up and pull out the heat shield slightly to clear the head screws and then hang it on the top bracket (located directly above the heat shield). Bracket Heat Shield 14) Disconnect the 2 grey connectors from the modulator coil. 6) Replace the front burner orifi ce with orifi ce #[...]

Regency ® L676 Direct V ent Gas Fireplace 30 INST ALLA TION 17) Ensure that the new rubber gasket (supplied with coil) is properly positioned and install the new modulating pressure regulator as- sembly to the valve using the screws sup- plied with the kit. T ighten screws securely . 18) Install the enclosed identifi cation label to the valve bod[...]

Regency ® L676 Direct V ent Gas Fireplace 31 INST ALLA TION LP Conversion Kit Contains: Qty . Part # Description 1 910-462 LP Conversion Coil 1 904-573 Cable T ie 1 910-037 LP Pilot Orifi ce 1 904-345 Orifi ce #53 (back) 1 904-241 Orifi ce #56 (front) 1 904-529 Allen Key 1 918-590 LP Conversion Decal 1 908-528 Red Propane Label 1 918-596 Instru[...]

Regency ® L676 Direct V ent Gas Fireplace 32 INST ALLA TION 13) Carefully remove the bottom brick panel. Bottom Brick Panel 14) Loosen the 2 screws that hold the right side heat shield. 15) Lift up and pull out the heat shield slightly to clear the head screws and then hang it on the top bracket (located directly above the heat shield). Bracket He[...]

Regency ® L676 Direct V ent Gas Fireplace 33 INST ALLA TION 25) Remove the pilot shield by removing the 2 screws. 26) Remove the clip from the pilot head assembly using a fl at head screw driver . 27) Remove the NG pilot orifi ce with the Allen Key and replace with LP pilot orifi ce. 28) Re-install the pilot head and pilot shield. Pilot Shield [...]

Regency ® L676 Direct V ent Gas Fireplace 34 INST ALLA TION BRICK P ANEL INST ALLA TION IMPORT ANT : Must install 1 set of brick panels. The operation of this unit without the brick panels is prohibited. Dangerous operating conditions may occur if the panels are broken. Handle with care. DO NOT FORCE INTO POSITION. Interior Brick Panel Installatio[...]

Regency ® L676 Direct V ent Gas Fireplace 35 INST ALLA TION 7) Slide the left side brick panel into position and secure in place with the brick panel clip that was removed in step 3. 1) Ensure installation of the logs and glass door has been completed before installing the exterior brick panels. 2) Line up the pins in the exterior base brick panel[...]

Regency ® L676 Direct V ent Gas Fireplace 36 INST ALLA TION LOG SET INST ALLA TION Installation of Interior Brick Panels must be completed before installing the log set. Read the instructions below carefully and refer to the diagrams. If the logs are broken do not use the unit until they are replaced. Broken logs can interfere with pilot operation[...]

Regency ® L676 Direct V ent Gas Fireplace 37 INST ALLA TION 6) Spread all of the Embers on the bottom brick panel around the burner tube and inbetween the front burner tube and the grate as shown. 03-25 03-27 03-26 03-28 Complete Log Set Installation 7) Spread the vermiculite on the base brick panel covering the remaining exposed base brick. Ember[...]

Regency ® L676 Direct V ent Gas Fireplace 38 INST ALLA TION INST ALLA TION WIRING DIAGRAM A receptacle is provided on the left hand side of the unit. 120 V olt AC power must be wired to the receptacle and the control module plugged in for the unit to operate fully . The front and rear burners will operate on low , when the unit is running on batte[...]

Regency ® L676 Direct V ent Gas Fireplace 39 OPERA TION OPERA TING INSTRUCTIONS OPERA TING INSTRUCTIONS 1) Read and understand these instructions before operating this appliance. 2) Check to see that all wiring is correct and enclosed to prevent possible shock. 3) Check to ensure there are no gas leaks. 4) Make sure the glass in the door frame is [...]

Regency ® L676 Direct V ent Gas Fireplace 40 OPERA TION OPERA TING INSTRUCTIONS NOTE: The control knob is located on the right hand side of the fi rebox behind the right side exterior brick panel. 1) Push in gas control knob slightly and turn clockwise to “OFF”. Knob cannot be turned from “PILOT” to “OFF” unless knob is pushed in slig[...]

Regency ® L676 Direct V ent Gas Fireplace 41 OPERA TION OPERA TING INSTRUCTIONS COPY OF LIGHTING PLA TE INSTRUCTIONS TO TURN OFF GAS APPLIANCE FOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTIONS 1) Push in gas control knob slightly and turn clockwise to “OFF”. Knob cannot be turned from “PILOT” to “OFF” unless knob is pushed in [...]

Regency ® L676 Direct V ent Gas Fireplace 42 MAINTENANCE MAINTENANCE MAINTENANCE INSTRUCTIONS 1) Always turn off the gas valve before cleaning. For relighting, refer to lighting instructions. Keep the burner and control compartment clean by brushing and vacuuming at least once a year . When cleaning the logs, use a soft clean paint brush as the lo[...]

Regency ® L676 Direct V ent Gas Fireplace 43 MAINTENANCE MAINTENANCE 1) Remove the exterior brick panels. 2) Remove the glass door . 4) Lift up and pull out the heat shield slightly to clear the screwheads and then hang it on the top bracket (located directly above the heat shield). 5) Unplug the power source. 6) Loosen the bottom screw and remove[...]

Regency ® L676 Direct V ent Gas Fireplace 44 MAINTENANCE MAINTENANCE 6 ) Remove the top screw and loosen the bottom screw that hold the power module in place. 7) Remove the power module cover by removing the 2 screws, one on each side. 8) Remove the 3 connectors from the circuit board. 9) Remove the circuit board from the support bracket by turnin[...]

Regency ® L676 Direct V ent Gas Fireplace 45 MAINTENANCE MAINTENANCE 6) Cut the cable tie that is holds the wires connected to the control module. 7) Disconnect the 3 connectors from the control module. 8) Pull out the control module. NOTE: The control module is held in place with velcro. 1) Remove the exterior brick panels. 2) Remove the glass do[...]

Regency ® L676 Direct V ent Gas Fireplace 46 MAINTENANCE MAINTENANCE 3) Loosen the 2 screws that hold the left side heat shield in place. 4) Lift up and pull out the heat shield slightly to clear the screwheads and then hang it on the top bracket (located directly above the heat shield). 8) Remove the battery cover from the DC Sparker Box. 9) Disc[...]

Regency ® L676 Direct V ent Gas Fireplace 47 MAINTENANCE 1) Remove the exterior brick panels. 2) Remove the glass door . V AL VE TRA Y REPLACEMENT a. Release the 2 door latches on the left and right side at the top of the fi rebox. b. Swing the door out from the top and release the hinges on the left and right side of the door by lifting them up.[...]

Regency ® L676 Direct V ent Gas Fireplace 48 MAINTENANCE 21) Replace the valve tray and reverse steps to re-install. 22) T urn on the gas supply and check for gas leaks. 23) Plug in the power source. 24) Re-install the left heat shield. 25) Re-install the grate. 26) Re-install the interior brick panels. 27) Re-install the log set. 28) Re-install t[...]

Regency ® L676 Direct V ent Gas Fireplace 49 P AR TS LIST P ARTS LIST MAIN ASSEMBL Y Part # Description 1) 521-527 Flue Collar Inner Assembly 2) 502-008 Flue Collar Outer 5) 904-732 Cap Screws 1/4" x 2-3/4" 6) W260280 Gasket T op Relief Plate 7) 770-066F T op Relief Plate 8) 942-1 17 T op Relief Frame 9) W260260 T op Relief Frame Gasket [...]

Regency ® L676 Direct V ent Gas Fireplace 50 P AR TS LIST P ARTS LIST[...]

Regency ® L676 Direct V ent Gas Fireplace 51 P AR TS LIST BURNER & LOG ASSEMBL Y Part # Description 30) 521-015 Bracket Log T ray 31) 521-016 Log T ray 32) 521-042 Defl ector Log T ray 35) 948-455 Burner Rear NG/LP 36) 948-454 Burner Front NG/LP 37) 521-050 Grate 40) 521-063 Bracket Log Position 41) 502-061 Pilot Shield 42) 380-013 Pilot Hold[...]

Regency ® L676 Direct V ent Gas Fireplace 52 P AR TS LIST NOTES[...]

Regency ® L676 Direct V ent Gas Fireplace 53 P AR TS LIST NOTES[...]

Regency ® L676 Direct V ent Gas Fireplace 54 P AR TS LIST NOTES[...]

Regency ® L676 Direct V ent Gas Fireplace 55 W ARRANTY Regency ® Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance T eam care fully inspects each unit thoroughly before it leaves our facility . FPI Fireplace Products International Ltd. is pleased to extend this limited lifetime wa[...]

Installer: Please complete the following information Dealer Name & Address: ______________________________________________ ___________________________________________________________________ Installer: ___________________________________________________________ Phone #: ___________________________________________________________ Date Installed:[...]