Regency P42-LP4 manuale d’uso

FPI FIREPLACE PRODUCTS INTERNA TIONAL L TD. 6988 V enture St., Delta, BC Canada, V4G 1H4 918-523a MODELS: P42-NG4 Natural Gas P42-LP4 Propane P42 Gas Fireplace W ARNING: If the information in these instructions are not followed exactly , a fi re or explosion may result causing property damage, personal injury or loss of life. FOR YOUR SAFETY Do no[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 2 T o the New Owner: Congratulations! Y ou are the owner of a state-of-the-art Gas Fireplace by FIREPLACE PRODUCTS INTERNA TIONAL. The P42 is a hand crafted appliance and has been designed to provide you with all the warmth and charm of a wood fi replace at the fl ick of a switch. The mod[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 3 T ABLE OF CONTENTS OPERA TING INSTRUCTIONS Optional Remote Control ............................................. 34 Optional W all Switch .................................................... 34 Optional W all Thermostat ........................................... 34 Operating Instructions[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 4 This is a copy of the label that accompanies each P42 Zero Clearance Direct V ent Gas Fireplace. We have printed a copy of the contents here for your review . The safety label is located on the front inside base of the unit, visible when the bottom louver is open. SAFETY LABEL NOTE: Regen[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 5 REQUIREMENTS 5.08: Modifica tions to NFPA-54, Chap ter 10 (2) Revise 10.8. 3 by adding the following a dditional requi rements: (a) For all side wall hor izontally ve nted gas fueled e quipment installe d in every dwelling, bui lding or str ucture used in whole or in part for residential [...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 6 14) Under no circumstances should any solid fuels (wood, paper , cardboard, coal, etc.) be used in this appliance. 15) The appliance area must be kept clear and free of combustible materials, (gases and other fl ammable vapours and liquids). INST ALLA TION CHECKLIST 1) Locate appliance, [...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 7 Diagram 1 INST ALLA TION UNIT SPECIFICA TIONS This includes: 1) Clocking the appliance to ensure the correct fi ring rate (rate noted on label 35,000 Btu/h) after burning appliance for 15 minutes. 2) If required, adjusting the primary air to ensure that the fl ame does not carbon. First[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 8 MANTEL LEG CLEARANCES Combustible mantel leg clearances as per diagram below: MANTELS Because of the extreme heat this fi replace emits, the mantel clearances are critical. Combustible mantel clearances from louver are shown in the diagram below . Note: A non-combustible mantel may be in[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 9 Position of T op Facing Support for material depth of 3/4” to 1-1/2" T op Facing Support T OP ASSEMBL Y & NAILING STRIPS The T op Facing Support and Side Nailing Strips must be correctly positioned and attached before the unit is slipped into position. 1) The top standoffs are [...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 10 EXTERIOR VENT TERMINA TION REQUIREMENTS INST ALLA TION A= Clearance above grade, veranda, porch, deck, or balcony *(min. 12"/30cm) B= Clearance to window or door that may be opened *(12"/30cm) C= Clearance to permanently closed window *(min. 12"/30cm) D= V ertical clearanc[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 11 6-7/8" (173mm) dia. Flue pipe 4" (102mm) dia. flue pipe T ermination Cap Part #946-523/P AstroCap spring spacer W all Thimble (2 pc) INST ALLA TION VENTING Regency ® Direct V ent System (Flex) Horizontal T erminations Only These venting systems, in combination with the P42 Dir[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 12 4” X 6-5/8” RIGID PIPE CROSS REFERENCE CHART Components from different Manufacturers may not be mixed. Not All Rigid Pipe components are available directly from FPI. Description Simpson Direct V ent Pro ® Simpson Direct V ent GS ® Discontinued Selkirk Direct-T emp™ American Metal[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 13 Description Simpson Direct V ent Pro ® Simpson Direct V ent GS ® Discontinued Selkirk Direct-T emp™ American Metal Products ® Amerivent Direct Metal-Fab ® Sure Seal Security Secure V ent ® Attic Insulation Shield 12” 46DV A-IS - N/A from FPI N/A N/A 4DAIS12 N/A SV4RSA Attic Insu[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 14 Rigid Pipe Adaptor (Part# 510-994) Pipe Length V ertical T erminal S torm Collar Part # 953 Flashing 943 or 943S Ceiling Firestop (Part # 963) 24" Pipe Length Adj.Pipe Length 1 1" - 14-5/8" 90 Elbow o Horizontal T erminatio n Cap W all Thimble Part # 942 Vinyl Siding S tan[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 15 INST ALLA TION RIGID PIPE VENTING ARRANGEMENTS - HORIZONT AL TERMINA TIONS REGENCY ® DIRECT VENT SYSTEM (FLEX) (Propane & Natural Gas) The shaded areas in the diagram show all allowable combinations of vertical runs with horizontal terminations. The chart below shows the distances w[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 16 INST ALLA TION RIGID PIPE VENTING ARRANGEMENTS - HORIZONT AL TERMINA TIONS REGENCY ® DIRECT VENT SYSTEM (FLEX) - Propane & Natural Gas The diagram below shows examples of horizontal termination arrangements using two 90 o elbows. If length "B" is increased, length "A&[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 17 INST ALLA TION RIGID PIPE VENTING ARRANGEMENTS - VERTICAL TERMINA TIONS (Propane & Natural Gas) Note: Must use optional rigid pipe adaptor when using rigid vent systems (Part # 510-994). Note: Regency ® Direct V ent System (Flex) is only approved for horizontal terminations. The sha[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 18 The P42 is approved for a 23 ft. (7.0m) vertical, with a maximum 12 ft (3.7m) horizontal offset using two 90 o elbows (two 45 o elbows equal one 90 o elbow) with rigid pipe vent systems for Propane and Natural Gas, as per the diagram below . • No V ent restrictor is required. • V ent[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 19 Flex Liner Exhaust Flue A maximum of two certified joiner kits may be used per length. #948-305 (35 ft) Air Intake Co-linear DV V ertical T ermination Cap # 946-529 Co-Linear Flex Adapter with Kit# 946-563 Outer Pipe with Kit# 946-563 Inner Pipe Adapter with Kit# 946-563 Rigid Pipe Adapt[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 20 INST ALLA TION VENTING ARRANGEMENTS - VERTICAL TERMINA TIONS with Co-linear Flex System for both Residential & Manufactured Homes into Masonry Fireplaces The shaded area in the diagrams show the allowable vertical terminations.[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 21 INST ALLA TION Below Grade Installation If the Snorkel T ermination must be installed below grade, i.e. basement application, proper drainage must be provided to prevent water from entering the Snorkel T ermination. Refer to Diagram 4. Do not attempt to enclose the Snorkel within the wal[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 22 1) Maintain the 1 - 1/4"(32mm) clearances (air spaces) to combustibles when passing through ceilings, walls, roofs, enclosures, attic rafter , or other nearby combustible surfaces. Do not pack air spaces with insulation. Check the "Rigid Pipe V enting Arrangements" section[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 23 INST ALLA TION 3) Assemble the vent assembly by applying Mill Pac to the 4"(100mm) inner collar of the termination and slipping the 4"(100mm) liner over it at least 1-3/8" (35mm). Fasten with the 3 screws (drilling pilot holes will make this easier). Apply Mill Pac or high[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 24 GAS LINE INST ALLA TION The gas line can be brought through either the right or the left side of the appliance. The gas valve is situated on the right hand side of the unit and the gas inlet is on the right hand side of the valve. Note: If the gas line is being installed from the left si[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 25 INST ALLA TION AERA TION ADJUSTMENT The aeration adjustment gears are located on the valve mounting plate and are accessed from underneath through the bottom louver opening. T o access the air shutter loosen the lock nut and then use the allen key to turn the turning gear which will adju[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 26 LOG SET INST ALLA TION INST ALLA TION 5) Place the front logs in the unit, aligning the holes on the underside of the logs with the log support pins in the front of the unit. Carefully push the logs down onto the pins. (Hint: Install the front right side fi rst.) 6) Place a few embers u[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 27 INST ALLA TION Diagram 1 Diagram 3 ST ANDARD FLUSH DOOR The standard fl ush door comes with a black frame. T o install the frame, simply hook the top door fl ange onto the top of the unit and swing the door towards the unit, diagram 1. Diagram 2 NOTE: Springs must always be OVER not un[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 28 BA Y LOUVERS 1) Install top louver by sliding the two bracket clips into the brackets located on top of the bay door . See below . The fi tted louver leaves a small gap between faceplate bottom and louver top. Attach 4 supplied magnets each to the back of the top and bottom trim pieces,[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 29 INST ALLA TION FULL SCREEN DOORS 2) Remove the Screen Doors from the Full Screen Door Frame by fully opening the doors and lifting up off of the hinges. See important note in step 9. Inside T op of Outer Frame 3) Full Screen Door Frame Installation a) Before attaching the Full Screen Doo[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 30 INST ALLA TION Inner Cut-Outs Bottom Flange NOTE: Should the fi nished wall protrude beyond the face of the unit, you can accommodate up to 1/2" depth. Simply push in the Full Screen Door Frame until it aligns against the fi nished wall. Secure T op Flange of Full Screen Door Fram[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 31 INST ALLA TION 10) Close screen doors. 8) Slide the T op Grill into the louver brackets located on the inside top of the fi rebox. Push in place. To p G r i l l 9) Install the Left and Right Side Screen Doors in the fully open position by placing over top of the hinges on the Full Scree[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 32 4-7/16" Openings for electrical connections Power IN Millivolt Wires 5-1/2" 1-1/2" WIRING DIAGRAMS CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. No electrical power supply is required for [...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 33 INST ALLA TION For PROP ANE Units and Units Equipped with DC Spark Boxes[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 34 OPTIONAL W ALL THERMOST A T A wall thermostat may be installed if desired, connect the wires as per the wiring diagram. Use table below to determine the maximum wire length. Note: P referable if the thermostat is installed on an interior wall. Regency ® offers an optional programmable t[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 35 COPY OF THE LIGHTING PLA TE INSTRUCTIONS OPERA TING INSTRUCTIONS 1) Push in gas control knob slightly and turn to “PILOT” position. 2) Push in control knob all the way and hold in until the pilot lights up. Continue to hold the control knob in for about 20 seconds after the pilot is [...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 36 1) Push in gas control knob slightly and turn clockwise to "OFF". Knob cannot be turned from "PILOT" to "OFF" unless knob is pushed in slightly . Do not force. 2) W ait 5 minutes to clear out any gas. 3) Turn knob on gas control countercloskwise to "PIL[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 37 MAINTENANCE W ARNING The use of substitute glass will void all product warranties. Do not operate the appliance with the glass panel(s) removed, cracked or broken. Replacement of the glass panel(s) should be done by an authorized service person. GLASS REPLACEMENT Y our P42 fireplace is s[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 38 REMOVING V AL VE 1) Shut off the gas supply . 2) Remove the louvers (and bay door if it is on). 3) Disconnect the inlet gas line. Note: Be sure to have an 1 1/16" wrench on the tee to ensure that the whole line is not twisted 4) Disconnect the 2 TP wires and the 2 TH wires from the [...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 39 INST ALLING V AL VE 8) Reinstall the 12 hold down screws. 9) Hook up the 2 TP and 2 TH wires to the appropriate connections on the valve. 10) Reinstall the burner grate. Put a dab of high temperature silicone over the 3 screw holes. 11 ) Install Burner tube. 12) Hook up the gas line and [...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 40 P ARTS LIST P42 MAIN ASSEMBL Y Part # Description Part # Description Part # Description 1) 910-142 Fan - Auto ON/OFF Thermodisc 2) 820-389 Thermodisc Bracket 3) 948-045 Chain 4) 948-1 15 Extension Spring 7) 910-184 T erminal Block 8) 510-125 T erminal Block Housing 9) 510-126 T er mi nal[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 41 P ARTS LIST P42 BURNER & LOG ASSEMBL Y Part # Description 602-574/P V alve Assembly - Natural Gas 602-576/P V alve Assembly - Propane 52) * Gasket - V alve Access Plate 56) 910-190 Piezo Ignitor & Nut 57) 910-478 V alve S.I.T . - NG/LPG 66) 910-038 Pilot Assy - S.I.T . - 3 Flame [...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 42 P42 FLUSH DOOR & LOUVERS Part # Description 600-960 Flush Louvers (Set) - Gold/Black 600-958 Flush Louvers (Set) - Black 600-961 Flush Louvers (Set) - Steel/Black 133) * Flush Louver Assy-T op 134) * Flush Louver Assy-Bottom Flush Door Assembly Complete 135) 940-086/P Glass (Flush) 1[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 43 P42 BA Y FRONT & LOUVERS 603-930 Bay Front Complete with Glass & Black Trim 106) 940-102/P Side Glass 107) 936-243 Glass Gasket 108) 940-101/P Center Glass 1 1 1) 602-906 Brick Panel - Bay Std Red 1 13) * Bay Door T rim (Each) -Black 602-932 Bay Door T rim (Set) - Gold 600-954 Ba[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 44 NOTES ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ______________________[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 45 NOTES ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ______________________[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 46 NOTES ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ______________________[...]

Regency ® P42-4 Zero Clearance Direct V ent Gas Fireplace 47 W ARRANTY Regency Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance T eam carefully inspects each unit thoroughly before it leaves our facility . FPI Fireplace Products International Ltd. is pleased to extend this limited[...]

Installer: Please complete the following information Dealer Name & Address: ______________________________________________ ___________________________________________________________________ Installer: ___________________________________________________________ Phone #: ___________________________________________________________ Date Installed:[...]