Renesas HS3802ECH62HE manuale d’uso

2003.12.19 H8/3802 Group FP-64E User System Interface Cable for E6000 Emulator User’s Manual H8/3802 HS3802ECH62HE Renesas Microcom puter Development Envi ronment System H8 Famil y/H8/300L Super Low Power Series Rev.3.00[...]

Cautions Keep safety first in your circ uit designs ! 1. Renesas Technology Corp. put s the maxi mum effort into maki ng semiconduct or product s better and more reliable, but the re is always the possi bility that trouble may occur with them. Trouble with semi conductors may lead to personal injury, fi re or propert y damage. Remember to give due [...]

I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this u ser system interface cable. • KEEP the user's manual handy for future reference. Do not atte mpt to use the user syste m interface ca ble until you fully under stand its mec h an is m. User Syst em Interface Cable: Throughout thi s document, t he ter m &q[...]

II LIMITED WARRANTY Renesas warrants its user system interface cabl es to be manufactured in accordance with published specifications and free from defects in material and/or workmanship. Renesas will re pair or replace any user system interfac e cables determine d to be defective in ma terial and/or workmanship. User s ystem interface cables are w[...]

III State Law: Some states do not allo w the exclusion or li mitation of implied warranties or liability for incidental o r consequen tial damages, so t he above limitation o r exclus io n may no t ap ply to you. This warr ant y give s yo u spec if ic lega l rig hts, and you ma y have other rig hts wh ic h may va ry fro m state to state. The Warran[...]

IV SAFETY PAGE READ FIRST • READ this user's manual before using this u ser system interface cable. • KEEP the user's manual handy for future reference. Do not atte mpt to use the user syste m interface ca ble until you fully under stand its mec h an is m. DEFINITION OF SI GNAL WORDS This is the safet y alert symbol. It is used to a l[...]

V W ARNING Observe the pr ecautions listed below. Failur e to do so will result in a FIRE HA ZARD and will damag e the user system and the emula tor product or will resu lt in PERSONAL INJURY. Th e USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product b y yourself for e lectric sho ck prevention and quality assurance. 2. Alway[...]

i Preface Thank y ou for pu rchasing this u ser sy stem interface cable (HS3802ECH62H) f or the Ren esas’s origin al m icrocom puter H8/3802, H8/ 38004 group. The HS3802ECH62H is a u ser sy stem interface cable that con nects an H8/3802, H8/38004 group E6000 emu lator (HS3800EPI60H; h ereinaf ter referred to as the em ulator) t o the IC sock et f[...]

ii Contents Section 1 Configuration .................................................................................... 1 Section 2 Connection Procedures ...................................................................... 3 2.1 Connectin g User Sy stem Interf ace Cable to Em ulator Station .......................................... 3 2.2 Connec[...]

1 Section 1 Configuration CAUTION Use an IC149-064- 175-B51 socket (manuf actured by YAMAICHI ELECTRONICS Co., Ltd.) for the FP-64E package IC socket on th e user system. Figu re 1 show s the con figuration of the HS3802EC H62H user sy stem interf ace cable for the FP-64E package. User system IC socket Cable head To emulator station Cable body Scre[...]

2 Table 1 lists t he HS3802ECH62H com pon ents. Pleas e mak e sure y ou h ave all of these compon ents w hen un packing. Table 1 HS3802ECH62H Com ponen ts No. Component Quantity Remarks 1 Cable body 1 Flat cable 2 Cable head 1 3 IC socket 1 For the FP-64E package 4 Socket cover 1 For installing an FP-64E-packaged MC U 5 Screws (M 2 x 12 mm) 4 For f[...]

3 Section 2 Connection Procedures 2.1 Conn ecting User System Interf ace Cable to Emulator Stati on W ARNING Observe the precautions listed below. Failure t o do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user sys[...]

4 Emulator station Cable body connector User system interface cable E6000 Figure 2 Connecting User System Interface Cable to Em ulator Station[...]

5 2.2 Conn ecting User System Interf ace Cable to User System W ARNING Always switch OFF the user syst em and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part . Before connecting, make sure that pin 1 on bot h sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will dama[...]

6 2.2.3 I nserting Cab le Head CAUTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an FP-64E pack age on the u ser system w ith pin 1 on the user system interf ace cable head, and insert th e user sy stem in terface cable head into th e IC socket on the user sy stem, as sh own in figu re 3. 2.2.4 Fas tening Cable [...]

7 Fasten the us er system interface cable h ead to the IC socket f or an FP-64E package on the user system with the four screws (M2 x 12 m m ; w ith fou r flat w ashers ) provided. Each screw sh ould be tighten ed a little at a time, alternatin g betw een screw s on oppos ing corners. Take special care, such as m anually securin g the IC socket sol[...]

8 2.2.5 Fastening Cable B ody Connect the cable body t o the cable head. Cable body Cable head Remove jig Push the remove jig User system Removing Figure 4 Fastening Cable Body[...]

9 2.3 Recom mende d Dime nsions for User Syst em M ount Pad Figure 5 show s the recom m ended dim ensions f or the mou nt pad (footprint) f or the user sy stem w ith an IC socket f or an FP-64E pack age (IC149- 064-175-B51: man ufactu red by YA MAIC HI ELECTRONICS C o., Ltd.). Note that the dim ension s in fig ure 5 are som ewh at differen t from t[...]

10 2.4 Dimension s for User S ystem Interface Cable Head The dimens ions for the u ser sy stem interf ace cable head are show n in figure 6. Unit: mm Tolerance: ±0.5 mm 63.5 58.4 19.3 25.0 16.7 25.0 Figure 6 Dim ensions for User System Interface Cable Head[...]

11 2.5 Resul ting Dimension s after Conn ecting User System Interface Cab le The resulting dim ensions, af ter connecting the user sy stem in terface cable head to the u ser system , are show n in f igure 7. Cable head User system Unit: mm Tolerance: ±0.5 mm IC socket (IC149-064-175-B51 manufactured by YAMAICHI ELECTRONICS Co., Ltd.) 18.6 21.5 Fig[...]

12 Section 3 Installing the MCU to the User System CAUTION 1. Check the locat ion of pin 1 before inserting. 2. Use a Philips-type screwdriver whose head matches the screw head. 3. The tightening torque must be 0.29 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the f orce required to turn the screw becomes[...]

13 MCU Pin 1 IC socket (IC149-064-175-B51 manufactured by YAMAICHI ELECTRONICS Co., Ltd.) User system Screws (M2 x 6 mm) with flat washers Socket cover Figure 8 Installing M CU to User System[...]

14 Section 4 Verifying Operation 1. When u sing the H8/3802 g roup E6000 em ulator (HS3800EPI60H), t urn on t he em ulator according to th e procedures described in th e H8/3802 Group E6000 Em ulator User' s Manu al (HS3800EPI60HE). 2. Verify the user sy stem interface cable conn ections by accessing ports and ch ecking th e bus states of the [...]

15 Figure 9 sho ws th e system clock oscillator o n the user system interface cable an d the subclock input specificat ions. R2 270 R1 1 M HCU04 HCU04 To E6000 emulator OSC1 OSC2 System clock oscillator Ω Ω 4.0 V 19 ns max. 19 ns max. 4.0 V 1.35 V 0 V 5.0 V 1.35 V Subclock input specifications Figure 9 System Clock Oscillator and Subclock Input[...]

16 Section 5 Notice 1. Make sure that pin 1 on the us er system IC socket is correctly aligned w ith pin 1 on the cable head before insertin g the cable head in to the user sy stem IC socket. 2. The dimens ions of the recom m ended m ount pad for th e user sy stem IC sock et are differen t from those of the MC U. 3. This user sy stem interface cabl[...]

H8/3802 Group FP-64E User System Interface Cable For E6000 Emulator User's Manual Publication Date: Rev.3.00, December 19, 2003 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Technical Documentation & Information Department Renesas Kodaira Semiconductor Co., Ltd.  2003 Renesas Technology Corp. All rights[...]

H8/3 802 Grou p FP-64 E User Sy stem Inte rface C able for E600 0 Emul ator User’s Ma nual REJ10B0099-0300H[...]