Rheem Water Heater manuale d’uso

Owners Guide and Installation Instructions Solar Loline Gas Boosted Water Heater This water heater must be installe d and serviced by an authorised person. Please leave this guide with the householder. WARNING: Plumber – Be Aware Use copper pipe ONLY . Plastic pipe MUST NOT be used. It is a requirement of a solar water heater installation that al[...]

Notice to Victorian Customers from the Victorian Plumbing Industry Commission. This water heater must be installed by a licensed person as required by the Victorian Building Act 1993. Only a licensed person will give you a Compliance Certificate, showing that the work complies with all the relev ant standards. Only a licensed person will have insur[...]

CONTENTS HOUSEHOLDER – We recommend you read pages 4 to 25 . The other pages are intended for the installer but may be of interest. About Your Water Heater ............................................................4 How Your Water Heater Works .................................................11 Regular Care .....................................[...]

SOLAR CONTROLLER AND SOLAR MONITOR This Addendum is for use with installation instructions 126547A, 126548 A, 126550B, 126551B, 126552B, 1 26553B, 126554B, 126555B. SOLAR MONITOR The solar control unit on an electric boosted system may incorporate a solar monitor. The solar monitor is located on the side of the solar contro l unit and houses both a[...]

SOLAR CONTROLLER AND SOLAR MONITOR 2007 October 2 SK6203 Rev B COMMISSIONING When the electrical supply is switched on to the solar control unit at start up: • If there is no solar gain, the circulator will not activate and the green LED will emit a slow pulse. The slow pulse indicates the circulator is not activated and the power to the solar co[...]

SOLAR CONTROLLER AND SOLAR MONITOR 2007 October 3 SK6203 Rev B DIAGNOSTIC FEATURES OF THE SOL AR CONTROLLER The operational modes are: Flashes Operational Modes solid green (remains on) Standby mode green slow pulse Standby mode (power on for less than 48 hours) green rapid pulse Circulating water through collectors 3 x green Circulating water thro[...]

ABOUT YOUR WATER HEATER MODEL TYPE Congratulations for choosing a Rheem ® water heater. Your Rheem solar Loline™ water heater is designed for the solar collectors to be roof mounted and the solar storage tank to be installed at ground level. The solar storage tank is suitable for outdoor installation only and can be installed with Rheem NPT 200 [...]

ABOUT YOUR WATER HEATER 5 HOTTER WATER INCREASES THE RISK OF SCAL D INJURY This water heater can deliver water at temperatures which can cause scalding. Check the water temperature before use, such as when entering a shower or filling a bath or basin, to ensure it is suitable for the application and will not cause scald injury. We recommend and it [...]

ABOUT YOUR WATER HEATER 6 SAFETY This water heater is supplied with a thermostat, an over-temperature cut-out, and a combination temperature pressure relief valve. These devices must not be tampered with or removed. The water heater must not be operated unless each of these devices is fitted and is in working order. If the electrical conduit to the[...]

ABOUT YOUR WATER HEATER 7 TO TURN OFF THE WATER HEATER If it is necessary to turn off the water heater: • Shut down the gas control (refer to “Close Down Procedure” on page 51 ). • Close the gas isolation valve at the inlet to the gas control. • Switch off the electrical supply at the isolating s witch to the water heater (refer to note b[...]

ABOUT YOUR WATER HEATER 8 PIPE WORK AND INSULATION The solar hot and solar cold pipe work bet ween the solar storage tank and the solar collectors MUST BE of copper and fully insulated with closed cell polymer insulation or similar (minimum thickn ess 13 mm). The insulation must be weatherproof and UV resistant if exposed. The insulation is essenti[...]

ABOUT YOUR WATER HEATER 9 BLEEDING THE SOLAR COLLECTORS It is necessary to purge air from the collector circuit: • When the water heater is to be turned on and the solar collectors and solar hot and solar cold pipe work have been drained. • After maintenance has been conducted on the pipe work and ai r has entered the system. • If the circula[...]

ABOUT YOUR WATER HEATER 10 FREEZE PRO TECTION The system when installed in areas s ubject to freeze conditions must be installed with the solar hot and solar cold pipes fully insulated with closed cell polymer insulation (minimum thickness 13 mm) to offer protection against freeze damage. Freeze conditions occur below 6 ° C. The system has NO WARR[...]

HOW YOUR WATER HEATER WORKS The Rheem solar Loline system has its vitr eous enamel lined solar storage tank installed at ground level, remotely from the solar collectors. As the sun heats the water in the solar collectors the increase in temperature activates the circulator. The circulator then moves the water from the solar collectors through an i[...]

HOW YOUR WATER HEATER WORKS 12 PIEZO IGNITION The “Piezo” push button igniter makes lighting the pilot flame of your water heater very easy. Simply follow the instructions on the label attached to the back of the access door. There is no need for matches to light the water heater. PILOT IGNITER A permanent pilot flame burns to ignite the main b[...]

REGULAR CARE TEMPERATURE PRESSURE REL IEF VALVE This valve is near the top of the water heater and is essential for its safe operation. It is possible for the valve to release a little water through the drain line during each heating period. This occurs as the water is heated and expands by approximately 1/50 of its volume. wat er heater drain line[...]

REGULAR CARE 14 EXPANSION CONTROL VALVE In many areas, including South Australia, Western Australia and scaling water areas, an expansion control valve is fitted to the cold water line to the water heater. The expansion control valve may discharge a small quantity of water from its drain line during the heating period instead of the temperature pre[...]

REGULAR CARE 15 FLUSHING THE SOLAR COLLECTORS It may be necessary to flush the solar collectors if there is sediment in the water supply. This should be conducted in th e morning, within three hours of sunrise, when the water temperature inside the solar collector(s) is lower. • Open a hot water tap and allow the water to run for five (5) minutes[...]

TIMER OPERATION FUNCTIONS OF THE TIMER The timer is an accurate, electronic device which allows up to six (6) ON-OFF periods to be set per day. It is recommended only one (1) period per day be programmed into the timer. This will be sufficient for most installations. The timer is not weatherproof and must be installed indoors. It is recom mended th[...]

TIMER OPERATION 17 The function of the timer is to enable the gas burner to automatically boost the stored water temperature, if required, due to low solar energy gain during the day. This will ensure the solar storage tank is full of hot water for the evening hot water requirements. Warning: The timer is not waterproof. Do not splash the timer wit[...]

TIMER OPERATION 18 TO SET THE TIME TIME PROG DAY HR MIN z z z z z RANDOM y R z MAN SU OFF 13:30 Example: Setting the current time as Sunday at half past one in the afternoon i.e. 1:30 PM. • Press and hold the “TIME” button. • Press the “DAY” button to select the current day. • Press the “HR” button to select the current hour ( Not[...]

TIMER OPERATION 19 To set “OFF” time • Press and release the “PROG” button. MO TU WE TH FR SA SU TIMER OFF TIME PROG DAY HR MIN z z z z z RANDOM y R z MA N 18:30 If the timer has been reset, then “TIMER – OFF”, “– – : – –” and “MO TU WE TH FR SA SU” will be displayed on the screen. If the timer has not been reset, th[...]

TIMER OPERATION 20 MANUAL BOOSTING – “OVERRIDE” F UNCTION The timer also has an “OVERRIDE” function to allow for bo osting the temperature of the water in the solar storage tank, outside of the set hours. SU ON TIME PROG DAY HR MIN z z z z z RANDOM y R z MAN 09:15 • To activate manual boosting, press the “MAN” button once. The word [...]

SAVE A SERVICE CALL Check the items below before making a service call. You will be charged for attending to any condition or fault that is not related to m anufacture or failure of a part. NOT ENOUGH HOT WATER (OR NO H OT WATER) This can occur with new installations and is normally related to some misunderstandings as to the use of the timer and g[...]

SAVE A SERVICE CALL 22 • Air in collectors (No solar gain) It is possible under certain conditions, such as when the pipe work has been opened, that air may become trapped in the solar collectors. This will prevent the circulator from moving water around the collector circuit. The air will need to be purged from the solar collectors (refer to “[...]

SAVE A SERVICE CALL 23 TEMPERATURE PRESSURE RELIEF VALVE RUNNING • Normal Operation It is normal and desirable this valve allows a small quantity of water to escape during the heating cycle. However, if it discharges more than a bucket full of water in 24 hours, there may be another problem. • Continuous dribble Try gently raising the easing le[...]

SAVE A SERVICE CALL 24 TIMER APPEARS TO BE FUNCTIONING INCORR ECTLY Check the following: • Has the programming been set correctly? Check the programmed “ON” and “OFF” times (refer to “Timer Operation” on page 16 ). • Has the “R” (reset) button been inadvertently pressed? Reprogram the timer. • Has the timer been set to the “[...]

SAVE A SERVICE CALL 25 HIGH GAS BILLS With the installation of your new solar hot water system, maximum gas energy savings can be achieved with careful planning of hot water usage. Should you at any time, feel your gas account is too high, we suggest you check the following points: • Is the relief valve running excessively? (Refer to “Temperatu[...]

INSTALLATION – SOLAR STORAGE TANK THIS WATER HEATER I S FOR OUTDOOR INSTALLATION ONLY. THIS WATER HEATER I S NOT SUITABLE FOR POOL HEATING. Check the water heater is suitable for the gas type available. (refer to the rating label on the w ater heater) The system is suitable for installation with Rheem NPT 200 solar collectors. The system is not s[...]

INSTALLATION – SOLAR STORAGE TANK 27 The installation must comply with the requirements of AS/NZS 3500.4, AS/NZS 3000, AS 5601 and all local codes and regulatory authority requirements. In New Zealand, the installation must conform with NZS 5261 Code of Practice for Installation of Gas Burning Appliances and the New Zealand Building Code. The wat[...]

INSTALLATION – SOLAR STORAGE TANK 28 MAINS WATER SUPPLY Where the mains water supply pressure exceeds that shown in the table below, an approved pressure limiting valve is required and should be fitted as shown in the installation diagram (refer to diagram on page 40 ) . Model 260 Relief valve setting 1000 kPa Expansion control valve setting * 85[...]

INSTALLATION – SOLAR STORAGE TANK 29 HOT WATER DELIVERY This water heater can deliver water at temperatures which can cause scalding. It is necessary and we recommend that a temperature limiting device be fitted between the water heater and the hot water outlets in any ablution area such as a bathroom or ensuite, to reduce the risk of scalding . [...]

INSTALLATION – SOLAR STORAGE TANK 30 If a combination isolation valve and non return valve (duo or trio valve) is installed on the cold water line to the solar water heater and the cold water line to the temperature limiting device branches off after this valve, then a second non return valve must be installed between the cold water branch and th[...]

INSTALLATION – SOLAR STORAGE TANK 31 • water will be supplied to the cold water inlet of the temperature limiting device at a temperature exceeding the maximum recommended w ater supply temperature, or • when the hot taps are closed no water will be supplied to the cold water inlet of the temperature limiting device whilst hot water will cont[...]

INSTALLATION – SOLAR STORAGE TANK 32 ANODE TYPES The correct anode type for the water supply being used must be fitted in the water heater (refer to “Water Supplies” on page 56 ). The black anode is fitted as standard. Total Dissolved Solids in water supply to the water heater Anode colour code 0 – 40 mg/L Green 40 – 600 mg/L Black 600 ?[...]

INSTALLATION – SOLAR STORAGE TANK 33 DIMENSIONS AND TECHNICAL DATA RHEEM 531260 RHEEM 531260 Model 531260 Mass (tank): Empty 110 kg Full 370 kg Capacity & Boost: 260 litres Recovery (Boost) (natural gas @ 50 ° C rise) 100 litres Gas Details Hourly Gas Consumption (MJ) Min. Gas Pressure (kPa) Test Point Gas Pressure (kPa) Max. Gas Pressure (k[...]

INSTALLATION – SOLAR STORAGE TANK 34 TYPICAL INSTALLATION – OUTDOOR LOCATION[...]

INSTALLATION – SOLAR STORAGE TANK 35 ASSEMBLY OF SOLAR HOT AND SOLAR COLD PIPE CON NECTIONS • Use thread sealing tape or approved thread sealant. • All olive compression fittings must use brass or copper olives. • Ensure air bleed valve is open when filling collectors. • Insulate the air bleed valve and 3 way tee assembly connected to the[...]

INSTALLATION – SOLAR COLLECTORS SOLAR COLLECTOR LOCATION Consideration must be given to the position of the solar collectors in relation to the solar storage tank. There are limitations on the maximum length of the solar hot and solar cold pipes between the solar storage tank and the solar collectors. Refer to “Solar Storage Tank Location” on[...]

INSTALLATION – SOLAR COLLECTORS 37 • The installation must comply with the requirements of AS/NZS 3500.4 and all local codes and regulatory authority requirements. • Refer to the installation instructions supplied with the collector kit for details on the installation of the solar collectors. LATITUDE OF SOME AUSTRALIAN CITIES Adelaide 35 ° [...]

INSTALLATION – SOLAR COLLECTORS 38 WARNING: Plumber – Be Aware • The solar hot and solar cold pipes between the solar storage tank and the solar collectors MUST BE of copper and fully insulated with close d cell polymer insulation or similar (minimum thickness 13 mm). Thicker insulation may be required to comply with the requirements of AS/NZ[...]

CONNECTIONS – PLUMBING CONNECTION SIZE S • Hot water connection: RP¾/20 • Cold water connection: DN20 compression fitting. (cold water inlet of tank: RP¾/20). • Solar hot (from collector) connection: DN15 compression fitting. (solar hot water inlet of tank: RP¾/20). • Solar cold (to collector) connection: DN15 compression fitting. • [...]

CONNECTIONS – PLUMBING 40 OR A disconnection union must always be provided at the cold water inlet, solar cold water outlet, solar hot water inlet and hot water outlet on the water heater to allow for disconnection of the water heater. This water heater has either a plastic dip tube or fitting liner in the inlet and outlet fittings (see diagram).[...]

CONNECTIONS – PLUMBING 41 RELIEF VALVE The temperature pressure relief valve is shipped behind the front cover of the solar storage tank. This valve must be fitted before the water heater is operated. Before fitting the relief valve, make sure the probe has not been bent. Seal the thread with Teflon tape - never hemp. Make sure the tape does not [...]

CONNECTIONS – PLUMBING 42 BLEED VALVE DRAIN A copper drain line must be fitted to the bleed valve to carry the discharge clear of the water heater and solar controls. Connect the drain line to the bleed valve using a disconnection union. The pipe work from the bleed valve to the drain should be as short as possible and fall all the way f rom the [...]

CONNECTIONS – ELECTRICAL The power supply to the water heater must not be switched on until t he water heater is filled with water and a satisfactory megger reading is obtained. All electrical work and permanent wiring must be carried out by a qualified person and in accordance with the Standards Australia Wiring Rules AS/NZS 3000 and local autho[...]

CONNECTIONS – ELECTRICAL 44 The power consumption of the water heater is: Component Power consumption Comments Solar controls 14 Watts Constant l oad 4 Watts differential controller 6 Watts solenoid valve 4 Watts timer Solar circulator 36 Watts Maximum load at solar heating cycle start up 30 Watts Average load during the solar heat ing cycle The [...]

COMMISSIONING TO FILL AND TURN ON THE WATER HEATER The power supply to the water heater must not be switched on and the gas pilot or burner must not be lit until the water heater is filled with water and a satisfactory megger reading is obtained. • Open all of the hot water taps in the house (don’t forget the shower). • Open the cold water is[...]

COMMISSIONING 46 GAS INLET PRESSU RE IMPORTANT – CHECK the gas supply pressure at the inlet to the water heater with the water heater and all other gas burning appliances in the premises operating (burners alight). The minimum gas supply pressure is: Natural Gas 1.13 kPa Propane 2.75 kPa Butane 2.75 kPa If this minimum cannot be achieved, it ma y[...]

COMMISSIONING 47 TO TURN OFF THE WATER HEATER If it is necessary to turn off the water heater on completion of the installation, such as on a building site or where the premises is vacant, then: • Shut down the gas control (refer to “Close Down Procedure” on page 51 ). • Close the gas isolation valve at the inlet to the gas control. • Swi[...]

LIGHTING THE WATER HEATER FOR YOUR SAFETY READ BE FORE LIGHTING Warning: This gas water heater is designed to operat e reliably and safely as long as the operating instructions are followed exactly . You must comply with these lighting instructions at every stage. Make sure the water heater is filled with water and the water suppl y is on, otherwis[...]

LIGHTING THE WATER HEATER 49 LIGHTING INSTRUCTIONS Using the gas control light the water heater as follows: 1. Stop , read the safety information on page 48 . 2. Turn the gas control knob fully clockwise to the “ z ” (off) position. 3. Wait five (5) minutes so any build up of unburnt gas can escape. If you then smell gas, stop and follow “C?[...]

LIGHTING THE WATER HEATER 50 The main burner will now automatically ignite during the set timer period when heating is required and extinguish when the water has been heated to the set temperature. If the main burner does not light at the selected setting, t he water may already be at the selected temperature. Note: Never press the igniter button w[...]

LIGHTING THE WATER HEATER 51 CLOSE DOWN PROCEDU RE 1. Turn the gas control knob to the “ · ” position (pilot). This setting will leave the pilot flame alight however the main burner will not be able to light. 2. Turn the gas control knob to the " z " (off) position. This setting shuts the gas control down completely.[...]

DRAINING THE SOLAR COLLECTORS To drain the solar collectors and the solar hot and solar cold pipes: • Open a hot water tap and allow the water to run for five minutes immediately prior to draining the solar collector(s). This will assist in the transfer of any high temperature water in the solar collector(s) to the solar storage tank. • Close t[...]

DRAINING THE WATER HEATER To drain the water heater: • Open a hot water tap and allow the water to run for five minutes immediately prior to draining the solar storage tank. This will assist in the transfer of any high temperature water in the solar collector(s) to the solar storage tank. • Close the hot water tap. Warning: Exercise care, as wa[...]

This page is intentionally blank. 54[...]

This page is intentionally blank. 55[...]

WATER SUPPLIES Your water heater is manufactured to suit the wate r conditions of most Australian metropolitan supplies. However, there are some known water supplies which can have detrimental effects on the water heater and its operation and/or life expectancy. If you are unsure of your water quality, you can obtain information from your local wat[...]

WATER SUPPLIES 57 SATURATIO N INDEX The saturation index is used as a measure of the water’s corrosive o r scaling properties. In a corrosive water supply, the water can attack copper parts and cause them to fail. Where the saturation index is less than –1.0, the water is corrosive and warranty does not apply to a solar collector. In a scaling [...]

RHEEM SOLAR WATER HEATER WARRANTY - AUSTRALIA ONLY Rheem reserves the ri ght to transf er fully functi onal compone nts from the defec tive water heater t o the replacement wate r heater if req uired. The term “ water heater” used in the W arranty, Warranty Conditions and Warranty Exclus ions means the Rheem supp lied water heater( s), solar st[...]

RHEEM SOLAR WATER HEATER WARRANTY - AUSTRALIA ONLY 59 WARRANTY EXCLUSIONS 1. REPAIR AND RE PLACEMENT WORK WIL L BE CARRIED OUT AS S ET OUT IN THE RHEEM WATER HEATER WARRA NTY, HOWEVER THE FOLL OWING EXCLUSI ONS MAY CAUSE THE WATER HEA TER WARRANTY TO BECOME VOID AND MAY INCUR A SERVICE CHARGE AND / OR COST OF PARTS. a) Accidental damag e to the wat[...]

RHEEM SOLAR WATER HEATER WARRANTY - AUSTRALIA ONLY 60 WARRANTY Rheem will: a) Repair or, if neces sary replace any Rheem water heat er; or b) Replace any com ponent (or, if necessary, arrang e the installati on of a new water h eater), which falls within t he Warranty Periods specified below , subject to t he warranty cond itions and exc lusions. I[...]