Rose electronic CAT5 manuale d’uso

CrystalView Pro ™ CAT5 DIGITAL CAT5 KVM EXTENDER 10707 Stancliff Road Phone: (281) 933-7673 Houston, Texas 77099 WWW.ROSE.COM INSTALLATION AND OPERATIONS MANUAL[...]

LIMITED WARRANTY Copyright  Rose Electroni cs 2002. All righ ts reserved. No part of this manual may be reproduced, stored in a retr ieval system, o r transcribed in any form or any means, electronic or mech anical, including photo copying and re cording, without the prior written permission of Rose Ele ctronics. Rose Electronics Part # MAN-CRVP[...]

FCC/IC STATEMENTS, EU D ECLARATION OF CONFORMITY FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO-FREQUENCY INTERFERE NCE STATEMENTS This equipment generates, use s and can radiate radio frequency energy and if not installed and used properly, t hat is in strict accord ance with the manufacturer’s instructions may cause interference to[...]

TABLE OF CONTENTS Contents Disclaimer ...................................................................................................... 1 System intr oduction ....................................................................................... 1 Features .......................................................................................[...]

INTRODUCTION CRYSTALVIEW PRO CAT5 INSTAL LATION AND OPERATINS MANUAL 1 Disclaimer While every precaution has been taken in the preparation of this manual, the manufacturer assumes no responsibility for errors or o m issi ons. Neither does the manufacturer assume any liabi lity for damages re sulting from the use of the information contained h ere i[...]

2 CRYSTALVIEW PRO CAT5 INSTALLA TION AND OPERATIONS MANUAL Using the CrystalView Pro CAT5 to re motely access your compute r has several advantages over conventional CAT-5 extenders. The Cryst alView Pro CAT5 transmits data digitally whic h provides a cl ear, sh arp picture. Computers used in hazardous in du strial environment s ca n be accessed re[...]

CRYSTALVIEW PRO CAT5 INSTAL LATION AND OPERATINS MANUAL 3 DVI or VGA The CrystalView Pro CAT5 is designe d to work with any combination of VGA and DVI video cards and monitors. The ideal co nfiguratio n is using a DVI video card, a TFT monitor and DVI video cables. With this configuration, no adjustments are need ed. A set-up procedure may be neede[...]

MODELS 4 CRYSTALVIEW PRO CAT5 INSTALLA TION AND OPERATIONS MANUAL PC model Receiver Transmitter (Local KVM access) Transmitter (No local KVM access) Shown with serial and audio options Figure 1. PC model Connectors: Receiver unit  DVI-I – DVI/VGA – KVM stations video monitor connection.  (2) MiniDin-6 – KVM stations keyboard / mouse con[...]

CRYSTALVIEW PRO CAT5 INSTAL LATION AND OPERATINS MANUAL 5 Rack model The rack models consist of 1 to 10 independent units mounted in a single rack mountable chassis. Each unit is ind ividually configured and co nne cted to a corresponding remote or local unit. Transmitters and re ceivers can be installed in the same cha s sis.[...]

CABLES 6 CRYSTALVIEW PRO CAT5 INSTALLA TION AND OPERATIONS MANUAL CrystalView Pro CAT5 cables Transmitter unit to CPU cable CPU cables connect from the transmi tter to a CPUs keyboard, video monitor and mouse ports. Receiver to KVM station cable The keyboard, video monitor, and mouse cabl es on a KVM station can connect directly to the receiver or [...]

ON-SCREEN DISPLAY (OSD) CRYSTALVIEW PRO CAT5 INSTAL LATION AND OPERATINS MANUAL 7 Device Control - OSD The on-screen display prov ides an e asy way to define the following parameters: 1. Input select, graphic source, VGA or DVI 2. Scale mode, fixed screen resolution/scale mode 3. Brightness/contrast/Back level 4. Colors 5. Color temperatures 6. Col[...]

8 CRYSTALVIEW PRO CAT5 INSTALLA TION AND OPERATIONS MANUAL Select graphic source menu The Input Select menu is the first menu to display when the OSD is activated. This menu allows you to se lect the graphic source type. This is typically the video card type, VGA or DVI. Use the left or right arrow keys to select VGA or DVI and press [Enter}. The a[...]

CRYSTALVIEW PRO CAT5 INSTAL LATION AND OPERATINS MANUAL 9 The receiver will always generate an exac t reproduction of the source signal if the Fixed Resolution setting is set to “OFF”. The fixed resolution setting should be used if the monitor resol ution on the receiver is not capable of displaying the resolution se nt by the transmitter. If t[...]

10 CRYSTALVIEW PRO CAT5 INSTALLA TION AND OPERATIONS MANUAL The color and color temperature me nu can automatically calibrate for the best color parameters or they can be set manually . Use the left and right arrow keys to select the needed ICO N and press [ENTER]. Figure 5. Color / Color temp menu The automatic calibration adjusts for th e best co[...]

CRYSTALVIEW PRO CAT5 INSTAL LATION AND OPERATINS MANUAL 11 The image selection allows re-positioni ng of the image and for manually adjusting the number of pixels per lin e (pix elclock) and manually adjusting the phase. This option is only available with a VGA source. No adjustments are needed for a DVI so urce. Figure 6. Image menu Select to auto[...]

12 CRYSTALVIEW PRO CAT5 INSTALLA TION AND OPERATIONS MANUAL Figure 7. Tools menu Manually adjust the OSD Manually adjust the Horizontal OSD position Manually adjust the vertical OSD position OSD size – Select single o r double size Reset to factory defaults Manually adjust sharpnes s (O nly effective on fixed scaling). If you select fixed scaling[...]

CRYSTALVIEW PRO CAT5 INSTAL LATION AND OPERATINS MANUAL 13 No auto-detection of pixels and phase Color depth of the source scre en pi cture Low color mode: This mod e allows high frame rates, select for fast screen change s (i.e. video) Transmitting on CAT-5 wit h 5 bits/col or = 15 bits total = 32768 colors. High color mode: This m o de allows for[...]

INSTALLATION 14 CRYSTALVIEW PRO CAT5 INSTALLA TION AND OPERATIONS MANUAL Installation Please refer to the safety section first before proceeding with any installation or configuration of the CrystalView Pro CAT5. NOTE: If your CPU uses a DVI video card and the KVM station’s monitor is a TFT (flat panel) DVI monitor, pixelc lock and phase adjustme[...]

CRYSTALVIEW PRO CAT5 INSTAL LATION AND OPERATINS MANUAL 15 A. 1- Connect the appropriate CP U cable to the keybo ard, video monitor and mouse ports on the CPU and to the corresponding ports on the tran smitter. 2- Connect the transmitter to the re ceiver with up to 1,000 feet of CAT-5 cable. 3- Connect the KVM stations keyboard, video monitor, and [...]

16 CRYSTALVIEW PRO CAT5 INSTALLA TION AND OPERATIONS MANUAL SET-UP instructions (Mixed DVI and VGA) The following set-up instruction s are fo r systems that use a mixture of VGA and DVI products. Systems with DVI video card s, DVI monitors and use DVI cables normally do not require any set-up. Set-up consists of adjusting the pixelclock first, then[...]

CRYSTALVIEW PRO CAT5 INSTAL LATION AND OPERATINS MANUAL 17 Pixel clock set corr ectly Pixel clock set incor rectly Pixel clock set incor rectly Phase set incorrect l y Figure 10. Pixelclock/Phase examples If one or more vertical areas have smeared lines, th e pixelclock needs adjusting. If there are horizontal noise lines, flicker or smearing with [...]

18 CRYSTALVIEW PRO CAT5 INSTALLA TION AND OPERATIONS MANUAL Applying power Plug in the provided power adapters to a 110/220-volt source and to the power connector on the transmitter and receive r Unit. Only use the power adapter provided. GND and earth should not be conn ected. Mount ferrite rings in the DC lines to protect against electro magnetic[...]

OPERATING INSTRUCTIONS CRYSTALVIEW PRO CAT5 INSTAL LATION AND OPERATINS MANUAL 19 Operating instructions Once the transmitter and receiver units a re co nne cted and configured, the KVM station will function as if it were directly connected to a CPU or KVM switch. All applications, upgrades a nd PC configurations can be perform ed normally. If your[...]

TROUBLESHOOTING 20 CRYSTALVIEW PRO CAT5 INSTALLA TION AND OPERATIONS MANUAL Troubleshooting The troubleshooting section is used as a guide to un derstandi ng the capabilities of the CrystalView Pro CAT5 and for general troubleshooting. If you have any problems or question s concerning the installation, operatio n or usage of the CrystalView Pro CAT[...]

CRYSTALVIEW PRO CAT5 INSTAL LATION AND OPERATINS MANUAL 21 Smeared characters  Pixelclock adjustment incorrect. Manually or auto-d etect the pixelclock setting (See Figure 6)[...]

SERVICE 22 CRYSTALVIEW PRO CAT5 INSTALLA TION AND OPERATIONS MANUAL Service Information Maintenance and Repair This Unit does not contain any internal user-serviceab le parts. In the event a Unit needs repair or mai ntenance, you must first obtain a Return Authorization (RA) number from Ro se Electronics or an authori zed repair center. This Return[...]

SAFETY CRYSTALVIEW PRO CAT5 INSTAL LATION AND OPERATINS MANUAL 23 Safety The CrystalView Pro CAT5 KVM extender has bee n tested for conformance to safety regulations and requirement s, and has been certified for international use. Like all electroni c equipment, the CrystalView Pro CAT5 should be used with care. To protect yourself from po ssi ble [...]

24 CRYSTALVIEW PRO CAT5 INSTALLA TION AND OPERATIONS MANUAL Safety information Documentation reference symbol. If the produ ct is marked with this symbol, refer to the product documentation to get more information about the prod uct. WARNING A WARNING in the manual denotes a hazard that can cause injury or death. CAUTION A CAUTION in the manual den[...]

APPENDICES CRYSTALVIEW PRO CAT5 INSTAL LATION AND OPERATINS MANUAL 25 Appendix A. General specifications Maximum resolution VGA – 1600 x 1200 @ 60Hz DVI – 1600 x 1200 @ 60Hz Video compatibility DVI, SVGA, VGA, XGA, RGB Keyboard PS/2 Mouse PS/2 Transmitter power 90-240 VAC adapter to 6VDC / app. 8W Receiver power 90-240 VAC adapter to 6VDC / app[...]

26 CRYSTALVIEW PRO CAT5 INSTALLA TION AND OPERATIONS MANUAL Appendix B. Parts and cables Part Number Description CRK-2DTPPDVI Dual Digital Cat5 KVM extender NOTE: Part number with /AUD suffix include s audi o support CAB-CXV66MMnnn* PC – Transmitter to CPU CAB-CX0606Cnnn* PC – Transmitter to Switch (coax) CAB-WX0606Cnnn PC – Transmitter to Sw[...]

CRYSTALVIEW PRO CAT5 INSTAL LATION AND OPERATINS MANUAL 27 Appendix D. Rack mount instructions The optional rack mount kit includes the followin g items:  Two black anodized mounting bra c kets.  Four 6 - 32 x 3/8” flat head mounting screws. To rack mount your Crystal V iew Pro CA T5, attach the two rack mounting brackets to your Unit with [...]

10707 Stancliff Road Phone: (281) 933-7673 Houston, Texas 77099 WWW.ROSE.COM[...]