Ryobi A25RT01 manuale d’uso

OPERA TOR’S MANUAL ROUTER T ABLE A25R T01 SA VE THIS MANUAL FOR FUTURE REFERENCE Y our router table has been engineer ed and manufactured to our high standar d for dependability , ease of operation, and operator safety . When properly car ed for , it will give you years of rugged, trouble-free performance. WARNING: T o reduce the risk of injury ,[...]

2 T ABLE OF CONTENTS  Introduction ..................................................................................................................................................................... 2  W arranty ..................................................................................................................................[...]

3 GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below , may result in electric shock, fire and/or serious personal injury . READ ALL INSTRUCTIONS  KNOW YOUR POWER TOOL. Carefully r ead the router table operator’ s manual and the manual for the particular router you are using. Lear[...]

4 GENERAL SAFETY RULES  INSPECT TOOL CORDS PERIODICALL Y . I f dam aged, hav e rep air ed by a qua lif ied ser vic e tech nic ian at an auth ori zed serv ice facil ity . The cond uctor with ins ula tion having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor . If repair or replacement of the elec[...]

5 SYMBOLS Some of the following symbols may be used on this product. Please study them and learn their meaning. Pr oper interpretation of these symbols will allow you to operate the pr oduct better and safer . V V olts V oltage A Amperes Current Hz Hertz Frequency (cycles per second) W W att Power min Minutes Time Alternating Current T ype of curre[...]

6 SYMBOLS SERVICE Servicing requir es extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you r etur n the pr oduct to the near est AUTHORIZED SERVICE CENTER for repair . When servic- ing, use only identical replacement parts. WARNING: T o avoi d ser ious pers onal inju ry , do not atte [...]

7 ELECTRICAL SPEED AND WIRING The no-load speed of this product depends on the router you are using. This speed is not constant and decreases under a load or with lower voltage. For voltage, the wiring in a shop is as important as the motor’ s horsepower rating. A line intended only for lights cannot properly carry a power product motor . Wire th[...]

8 ST ARTING PIN FEED DIRECTION inch 1 0 1 2 3 Inch 1 0 1 2 3 Inch 1 Inch FEED DIRECTION 1 Fig. 2 FEA TURES PRODUCT SPECIFICA TIONS T able Dimensions ............................. 14 in. x 28 in. x 3/4 in. Maximum Cutter Diameter ................................. 1-15/16 in. Fence Length ............................................................. [...]

9 FEA TURES Fig. 3 SWITCH KEY SWITCH IN LOCKED POSITION SWITCH OFF SWITCH ON WARNING: Always remove the switch key when the tool is not in use and keep it in a safe place. In the event of a power failure, turn the switch OFF ( O ) and remove the key . This action will pr event the tool from accide ntally start ing when power returns. WARNING: AL WA[...]

10 Inch 1 0 1 2 3 Inch 1 0 1 2 3 FEED DIRECTION 1 2 3 1 2 3 UNP ACKING This product r equires assembly .  Carefully r emove the product and any accessories from the box. Make sure that all items listed in the packing list are included.  Inspect the product carefully to make sure no breakage or damage occurred during shipping.  Do not disca[...]

11 Fig. 7 ASSEMBL Y Fig. 5 ASSEMBLING THE ROUTER T ABLE Assembling the router table involves attaching the switch box, the under table guards, the legs, the router/insert plate assembly , the fence assembly , throat plate, starting pin, and installing the miter gauge to the router table. A TT ACHING THE SWITCH BOX See Figure 5. The switch box will [...]

12 ASSEMBL Y PRE-DRILLING HOLES FOR THROUGH T ABLE DEPTH ADJUSTMENT See Figure 8. Since each router will have differ ent placements for through table depth adjustments, pilot holes have been pre-drilled in the throat plate to assist in thr ough table adjustments. Only the models listed below in the key are available for use with the through table d[...]

13 ASSEMBL Y BRAND MODEL BASE TYPE F ASTENER SIZE INSERT PLA TE HOLES USED NUMBER OF HOLES Bosch 1617 Fixed 10-24 x 5/8 in. A1, A3, A5 3 Bosch 1617 EVS Fixed 10-24 x 5/8 in. A1, A3, A5 3 Bosch 1617 EVSPK Fixed 10-24 x 5/8 in. A1, A3, A5 3 Craftsman 17504 Fixed 10-32 x 5/8 in. A2, A4, A6 3 Craftsman 17505 Fixed 10-32 x 5/8 in. A2, A4, A6 3 Craftsman[...]

14 0 Inch 1 2 1 3 0 0 Inch 1 2 1 3 0 FENCE LOCK KNOBS CARRIAGE BOL TS FENCE LOCK KNOB WASHER SLOT Fig. 13 Inch 1 0 1 2 3 Inch 1 0 1 2 3 FEED DIRECTION ASSEMBL Y Fig. 12 INSERT PLA TE STRAIGHT EDGE ADJUSTING SCREWS HEX KEY CARRIAGE BOL T WASHER FENCE ASSEMBL Y MAKING INSERT PLA TE LEVEL See Figure 12.  Unplug the router table and/or the r outer .[...]

15 FEED DIRECTION Inch 1 0 1 2 3 Inch 1 0 1 2 3 Inch 1 0 1 2 3 Inch 1 0 1 2 3 FEED DIRECTION Fig. 16 ST ARTING PIN HOLES ST ARTING PIN INST ALL REMOVE Fig. 15 ASSEMBL Y Fig. 14 Inch 1 0 1 2 3 Inch 1 0 1 2 3 FEED DIRECTION THROA T PLA TE NOTCH T AB MITER GAUGE MITER GAUGE BAR POINTER SLOT The proper size throat plate depends on the size and shape of[...]

16 inch FEED DIRECTION 1 inch 1 V ACUUM HOSE V ACUUM PORT Inch 1 0 1 2 3 Inch 1 0 1 2 3 FEED DIRECTION Inch 1 0 1 2 3 Inch 1 0 1 2 3 FEED DIRECTION HEX NUT WORK T ABLE FLA T WASHER LOCK WASHER ASSEMBL Y CLAMP WORK T ABLE A TT ACHING THE V ACUUM HOSE See Figure 17. The vacuum port molded into the fence will accept either a 1-1/4 in. or 2-1/2 in. vac[...]

17 OPERA TION PERFORMING A ROUTING OPERA TION Observe the following rules when using the router .  Read the entir e operator’ s manual for the router and router table.  Plug the router table power cor d into a power source.  Always control the power to the router with the r outer table switch whenever the router is mounted on the table. [...]

18 1/4 0 Inch 1 0 1 2 3 Inch 1 0 1 2 3 FEED DIRECTION Inch 1 0 1 2 3 Inch 1 0 1 2 3 OPERA TION Fig. 20 MITER GAUGE KNOB MITER GAUGE INSERTING/REMOVING CUTTERS  Unplug the router table and/or the r outer .  Remove the fence assembly . (See Attaching the Fence Assembly in the Assembly section.) LOOSEN CUTTER PROPER DIST ANCE Fig. 21 FENCE LOCK [...]

19 MAINTENANCE WARNING: Do not at any time let brake fluids, gasoline, petroleum- based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may r esult in serious personal injury . Electric tools used on fiberglass material, wallboard, spack - ling compounds, or plaster are sub[...]

20 OPERA TOR’S MANUAL ROUTER T ABLE A25R T01 987000-114 03-08-07 (REV :00) A25RT01 • P AR TS AND SERVICE Prior to requesting service or purchasing replacement parts, please obtain your model and serial number from the pr oduct data plate. • MODEL NUMBER • SERIAL NUMBER • HOW TO OBT AIN REPLACEMENT P AR TS: Replacement parts can be purchas[...]