Sharp AF-R140DX manuale d’uso

ROOM AIR CONDITIONER INSTALLATION AND OPERATION MANUAL PAGE CONTENTS This INSTALLATION AND OPERATION MANUAL explains the proper use of your new Sharp Air Conditioner. Read these instructions carefully before installing or operating your air conditioner. The INSTALLATION AND OP- ERATION MANUAL should be kept in a safe place for handy reference. FOR [...]

2 To aid in answering questions if you call for service or for reporting loss or theft, please record below the model and serial number located on the right side of the unit. DATE OF PURCHASE Dealer Name Address City State Zip Telephone FOR YOUR PROTECTION TO PHONE: Dial 1-800-BE-SHARP (237-4277) for: SERVICE (for your nearest Sharp Authorized Serv[...]

3 SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Product"), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new [...]

4 INST ALLA TION INSTRUCTIONS Before beginning installation, read these instructions carefully. Use the enclosed MOUNTING KIT for proper installation. The mounting kit is designed for wooden sill double or single hung sash-type windows. Minimum opening (Without mounting kit) Mounting kit fully closed Mounting kit fully opened 22 / "(560mm) 27 [...]

5 No. Accessories Q'ty Right closure assembly Left closure assembly Window sash foam seal 1 1 1 1. Screw driver (medium size Phillips) 2. Tape measure or ruler 3. Knife or scissors INST ALLA TION INSTRUCTIONS 13 Screws(L=1", 25.4mm) Bottom gasket 8 1 6 Screws(L= / ", 10mm) 6 8 32 Window sash foam seal (adhesive type) 1 Battery Remote[...]

6 INST ALLA TION INSTRUCTIONS Open the window sash and place the cabinet on the sill. Close the window sash securely behind the top angle. If there is space between the bottom channel and the sill, fill the gap with a thin board or other hard filler. 5 Front panel Exhaust Lever Closure assembly Insert the right closure assembly and the left closure[...]

7 INST ALLA TION INSTRUCTIONS Closure assembly (Left) 6 Jamb (Left) Top angle Sill 1/2 inch (13mm) Closure assembly (Left) Stool Insert the closure assemblies on both sides into the rails of the jamb. Secure the cabinet to the window stool with 3 screws (L=1", 25.4 mm), working from the inside of the cabinet. Secure the top angle and the closu[...]

8 IMPORTANT: Points to keep in mind when using your air conditioner. • Install the air conditioner by following the installation instructions given in the previous section of this manua l. • Make sure the unit is the correct capacity for the area you want to cool. • Do not modify any part of this product. • Do not insert objects into any pa[...]

9 PRECAUTIONS • Allow 3 minutes for the compressor to restart cooling. If you turn the air conditioner off and immediately restart it, allow three minutes for the compressor to restart cooling. There is an electronic device in the unit that keeps the compressor off three minutes for protection. • If a power failure occurs during use, allow 3 mi[...]

10 TIMER ON/OFF pad TIMER indicator ENERGY SAVER pad ENERGY SAVER indicator POWER ON/OFF pad POWER indicator Receiver window for remote control signal Display SELECTOR indicator SELECTOR pad TEMPERATURE setting pad ---- Lower temp. ---- Raise temp. UNIT CONTROL P ANEL HOW T O OPERA TE Front panel Air inlet (Indoor side) Louvers Air outlet (Indoor s[...]

11 HOW TO OPERA TE --- Lower temp. --- Raise temp. Touch POWER ON/OFF pad. • The unit is preset at 74 ° F and HIGH COOL. This will show in the display when the power is first turned on. • POWER indicator and SELECTOR in- dicator (COOL) will light. To turn off the unit, touch POWER ON/OFF pad again . • POWER indicator and SELECTOR indicator w[...]

12 HOW TO OPERA TE T O CHANGE F AN SPEED AND OPERA TION MODE During operation Touch SELECTOR pad and select the operation mode and fan speed. • SELECTOR indicator and display will light in order as you touch. NOTES ON OPERA TION MODE: SELECTOR DISPLAY HIGH COOL MED COOL LOW COOL HIGH FAN MED FAN LOW FAN • The latest operation mode will be memor[...]

13 EXHAUST Lever HOW TO OPERA TE Adjust the louvers to change the direction of air flow for uniform and efficient cooling of the room. Vertical louvers Adjusts LEFT/RIGHT air flow If air in your room is stale, set the EXHAUST lever to the OPEN position. This will exhaust stale air to the outside. The EXHAUST lever should normally be kept in the CLO[...]

14 HOW TO OPERA TE ON TIMER OPERA TION (If you wish to start the operation 6 hours and 30 minutes later, set the delay time as shown above.) 1 Touch the TIMER ON/OFF pad to set the delayed start time. • The time setting will change as you touch the pad. The display will change as follows; • The timer will be set, 5 seconds after the TIMER ON/OF[...]

15 HOW TO OPERA TE OFF TIMER OPERA TION • This unit has a built-in timer that can be programmed to shut the unit off up to 12 hours in advance. You can set the timer to stop in increments of 30 minutes (0.5 hours) up to 9.5 hours in advance of the stop time, or in 1 hour increments from 10 to 12 hours in advance of the stop time. • The unit wil[...]

16 Insert the batteries in the compartment, making sure the and polarities are properly aligned. HOW TO OPERA TE INST ALLING BA TTERIES Use two size-AAA (R03) batteries. Battery compart- ment cover NOTES: • The battery life is approximately one year with normal use. • When you replace the batteries, always use two new ones of the same type. •[...]

17 HOW TO OPERA TE • The time setting will change as you push the button. The display will change as follows; • The last OFF time setting is memorized by the unit and will appear on the display when the button is pushed. • The timer will be set, 5 seconds after the SET TIMER/OFF button is pushed for the last time. • If you wish to cancel th[...]

18 ENERGY EFFICIENCY TIPS CLEANING AND MAINTENANCE CLEANING THE FIL TER If the filter is clogged with dust, the amount of air flow will be reduced, resulting in poor cooling performance. The filter should be cleaned every10 days. At the beginning of every cooling season or after a long period of inactivity, clean the filter before starting the unit[...]

19 BEFORE CALLING FOR SER VlCE IF YOUR AIR CONDITIONER DOES NOT OPERATE PROPERLY, PLEASE CHECK THE FOLLOWING ITEMS BEFORE CALLING FOR SERVICE. AIR CONDITIONER DOES NOT OPERATE AT ALL • Is the unit plugged in or is the plug loose? • Is the fuse blown or the circuit breaker tripped? • Did you restart the unit within 3 minutes after a power fail[...]

20 SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-2135 SHARP CORPORATION Osaka, Japan Printed in Thailand[...]