Siemens CFMC1315-LP manuale d’uso

Building Technologies Fire Safety & S ecurity Products CFMC1315-LP 1/3” 1.3 Megapixel IP Indoor Dome Col our Camera Configuration Manual[...]

Liefermöglichkeiten und tec hnische Änderungen vorbehalten. Data and design subject to change without not ice. / Supply subject to availability. © 2009 Copyright by Siemens Building Technologies Wir behalten uns alle Rechte an diesem Dokument und an dem in ih m dargestellten Gegenstand vor. Der Empfänger erkennt diese Rec hte an und wird dieses[...]

3 Siemens Building Technologies Fire Safety & Security Products 01.2009 Contents 1 Safe ty ....................................................................................................... 7 1.1 Target readers........................................................................................... 7 1.2 General safety precautions ......[...]

4 Siemens Building Technologies Fire Safety & Security Products 01.2009 7.5 Record ..................................................................................................... 37 7.5.1 FTP recording ......................................................................................... 37 7.5.2 SD recording ..........................[...]

5 Siemens Building Technologies Fire Safety & Security Products 01.2009[...]

[...]

Safety 7 Siemens Building Technologies Fire Safety & Security Products 01.2009 1 Safety 1.1 Target readers The instructions in this document are de signed only for the following target readers: Target readers Qualification Activity Condition of the product Operational startup personnel Technical training for building or electrical installations[...]

Safety 8 Siemens Building Technologies Fire Safety & Security Products 01.2009 Damage due to unsuitable mounting location z The environmental conditions re comme nded by the manufacturer must be observed. See section 4: Ordering Data. z Do not operate the device in dusty place s. z Do not expose the device to mechani cal vibrations or shocks. z[...]

EU directives 9 Siemens Building Technologies Fire Safety & Security Products 01.2009 2 EU directives The product complies with the requirements of the following EU directives. The EU declaration of conformity is available from: Siemens Building Technol ogies Fire & Security Products G mbH & Co. oHG 76181 Karlsruhe Germany European Dire[...]

Specifications 10 Siemens Building Technologies Fire Safety & Security Products 01.2009 3 Specifications Image System Description Image sensor 1/3” progressive ExviewHAD CCD, 1.3 Megapixels Effective pixels 1280 (H ) x 960 (V) Image compression method Motion JPEG/ MPEG4 Image frame rate SXGA: 1280 x 960 at 12.5 fps max. VGA 640 x 480, QVGA 32[...]

Ordering Data 11 Siemens Building Technologies Fire Safety & Security Products 01.2009 4 Ordering Data Type Art-No. Description Weight CFMC1315-LP S54561-C81-A1 1/3” 1.3 MP Indoor IP Dome Colour Camera 12 V DC / 24 V AC, 50 Hz or PoE 0.65 kg 4.1 Package Contents z CCD IP dome z Documentation CD z Utilities CD z Installation instruction (Engli[...]

Camera part and connector definition 12 Siemens Building Technologies Fire Safety & Security Products 01.2009 5 Camera part and connector definition 5.1 Camera part definition Fig. 1 Camera part definition 1 Alarm out terminal 13 Tilt ad j ust screws 2 Alarm in terminal 14 Horizontal ad j ustment rin g 3 Power IN connector 15 Zoom lever 4 Audio[...]

Camera part and connector definition 13 Siemens Building Technologies Fire Safety & Security Products 01.2009 5.1.1 Alarm out terminal YELLOW: ALARM OUT BLACK: COM Alarm output port 5.1.2 Alarm in terminal RED: ALARM IN ORANGE: GND External alarm input 5.1.3 Power IN connector WHITE: Power - BLACK: Power + POWER DC12V / AC24V 5.1.4 Audio in WHI[...]

Installing the camera 14 Siemens Building Technologies Fire Safety & Security Products 01.2009 6 Installing the camera 6.1 Precautions SD Memory card Please install the SD memory card before switching on the camera as the system can not detect the insertion of SD card during operation. z There is a limit to the number of rewrites that is possib[...]

Installing the camera 15 Siemens Building Technologies Fire Safety & Security Products 01.2009 z Do not use the power adapter in hot and humid pla ces. z Temperature increasing o n the surface of the adapter is normal. Before moving the adapter to another location, unplug it from the wall outlet, and wait until its temperature decreases z Buzzi[...]

Installing the camera 16 Siemens Building Technologies Fire Safety & Security Products 01.2009 z Camera search ap plication "IpFinder" Install this application from the CD-ROM suppli ed as an accessory. (Doubl e-click "ipfinder_Setup.exe" in t he CD-ROM and install the application in accordan ce with the instructions on the [...]

Installing the camera 17 Siemens Building Technologies Fire Safety & Security Products 01.2009 For more information, read your com puter's user's guide. Connecting Camera and Personal Computer 1. Connect LAN cable and turn the power on. Connect the LAN cable (straight cable) connected to the camera to the hub. Or, connect the camera t[...]

Installing the camera 18 Siemens Building Technologies Fire Safety & Security Products 01.2009 6.5 Using the Camera Search Application "IpFinder" The "IpFinder" is an application for searchin g network cameras that can currently be viewed from the administrator's personal computer or a use r's personal computer, an[...]

Installing the camera 19 Siemens Building Technologies Fire Safety & Security Products 01.2009 6.6 Using the Camera Search Application "Web cam IP manager" This assumes that: The Web-Cam IP Manager and all the unit s are locat ed in the same network segment. If a device and the Web-Cam IP Manager are not located in the same network se[...]

Installing the camera 20 Siemens Building Technologies Fire Safety & Security Products 01.2009 6.7 Log-in Screen 5. Open the Internet Explorer. 6. Enter the default IP address: 192.168.0. 10. You can also use Mozilla Firefox. In that case, you have to download the IE Tab plug-in from the Mozilla Firefox homepage. This product regards a person w[...]

Installing the camera 21 Siemens Building Technologies Fire Safety & Security Products 01.2009 3. Click the "Intranet" icon if the camera to be operated is inside the intranet, clicking the "Internet" icon if the camera is on the Internet. 4. Click "Level customize." 5. Check the following radio buttons in the disp[...]

Installing the camera 22 Siemens Building Technologies Fire Safety & Security Products 01.2009 Camera Image Screen When using Windows XP SP2 If fails to display the Camera Image screen, operate as follows. 1. Choose "Pop-up Blocker" on the tool menu. 2. Choose "Always Allow Pop-ups from This Site...". Components of unit home[...]

Configuration 23 Siemens Building Technologies Fire Safety & Security Products 01.2009 7 Configuration 7.1 Compression Image mode z Both functions of JPEG and MPEG4 are effective. z Two streams, 1 & 2 available for sele ction. Stream 1 can be set to JPEG and MPEG4, but only JPEG available for Stream 2 JPEG Following settings are enabled wh [...]

Configuration 24 Siemens Building Technologies Fire Safety & Security Products 01.2009 z Frame Rate: seven frame rates – 1, 2 , 3, 5, 10, 12, 25 – are available for selection. MPEG4 Following settings are enabled wh en "Compression Mode" is set to "MPEG4". z Resolution: 640 x 480 and 320 x 240 available. z Bit Rate: 6 mo[...]

Configuration 25 Siemens Building Technologies Fire Safety & Security Products 01.2009 How to operate RTSP NOTE You need to prepare suitable RTSP player such as Quicktime or VLC to receive the data streaming first then execute application program. This application is found on the CD included with delivery. z Perform VLC 1. Select Open then clic[...]

Configuration 26 Siemens Building Technologies Fire Safety & Security Products 01.2009 z Perform Quicktime 1. Select Open URL . 2. Then fill in rtsp://<IP address>:<rtsp_port>/livestream 3. Click OK. For example: rtsp://192.168.0.194:554/livestream . Regarding default value of RTSP port, it’s based on which strea m you select. Qui[...]

Configuration 27 Siemens Building Technologies Fire Safety & Security Products 01.2009 7.2 Network Settings You can setup your camera basic setti ng, DDNS, and FTP server by sele cting Network Settings in the Configuration menu.. 7.2.1 Basic Settings Basic Camera Name Input your camera name here. The default name is “nwcam05”. Camera Name E[...]

Configuration 28 Siemens Building Technologies Fire Safety & Security Products 01.2009 Bandwidth Cont rol OFF: The network Camera will stream images at the maximum frame rate allowed by the network. ON: The Network Camera will display images up to the set bandwidth; using a lower bandwidth results in lower frame rates. 7.2.2 DDNS Settings This [...]

Configuration 29 Siemens Building Technologies Fire Safety & Security Products 01.2009 7.3 Image Parameters 7.3.1 Camera - Basic settings Basic items such as size and quality of delivere d images of the camera can be set. 1. Select "Image Parameters" in the Configuration menu. Î A sub menu for Camera Settings will appear. 2. Click &q[...]

Configuration 30 Siemens Building Technologies Fire Safety & Security Products 01.2009 Slow Speed Shutter The Slow shutter can be tu rned “ON” if the sensitivity is still not so good under “High” gain condition at dark. The optimum image level can be maintained by appropriate gain and shutter combination which ar e determined automatica[...]

Configuration 31 Siemens Building Technologies Fire Safety & Security Products 01.2009 7.3.2 Camera-mask zone settings 1. Tick the checkbox “ON”, then click “Set Mask Zone” to start mask setting 2. Use the mouse to drag a mask recta ngle on the scre en, click “OK” to complete the selection. 3. Click “Save” to enable the mask set[...]

Configuration 32 Siemens Building Technologies Fire Safety & Security Products 01.2009 7.3.3 Camera-Cropping settings 1. Tick the "ENABLE" checkbox and fill in the name, then click “Set Cropping Area” to start cropping setting. Î A cropping setting screen will pop -up as shown, select one type of cropping from VGA, QVGA, 4CIF, 2C[...]

Configuration 33 Siemens Building Technologies Fire Safety & Security Products 01.2009 NOTE Up to 5 cropping areas can be set on the screen. The MPEG4 function is not supported when the cro pping function is on. 7.3.4 Camera-OSD settings This function setups the text position and colour of camera name, Alarm text or DATE/TIME on the screen. Of [...]

Configuration 34 Siemens Building Technologies Fire Safety & Security Products 01.2009 7.4 Alarm External alarms and motion sensors can be set. Connecting a sen sor or other device to the alarm input terminal notifies an alarm when the sens or detects a trouble. For example, mounting a sensor on a door notifies an al arm each time the door is o[...]

Configuration 35 Siemens Building Technologies Fire Safety & Security Products 01.2009 NOTE A speaker with amplifier inside shall be connected to AUDIO out jack on rear panel. 7.4.2 Motion detection settings The setting is similar to alarm input with some additio nal functions: z Motion detection – Set on, open motion detection function. – [...]

Configuration 36 Siemens Building Technologies Fire Safety & Security Products 01.2009 7.4.3 Alarm output z Alarm mode: The alarm output can be turned OFF or be activated when any of the following events occurs: – Event: Once alarm input1 or ala rm input 2 or motion is triggered, the alarm out will be triggered immediately as well. z Output h[...]

Configuration 37 Siemens Building Technologies Fire Safety & Security Products 01.2009 7.5 Record 7.5.1 FTP recording You can save image files via FTP. Set up your FTP recording condit ions first, then identity your FTP sever 1 and 2. FTP recording conditions You can store your image files based on y our sche duled recording, or reco rding by a[...]

Configuration 38 Siemens Building Technologies Fire Safety & Security Products 01.2009 z Recording by Alarm Configure "Alarm input setting" first. Then select the recording format: – Record source: choose JPEG or MPEG4 format – Record frame Set the number of images to be recorded immediatel y after an alarm occurs. Images of the m[...]

Configuration 39 Siemens Building Technologies Fire Safety & Security Products 01.2009 z FTP server name: Input a server name or addre ss z Login ID: Limited only to users who ha ve authority to access the server. z Password: Input the registered passwo rd associated with Login ID. z Password (Confirm): Re-enter the password z FTP Port Number: [...]

Configuration 40 Siemens Building Technologies Fire Safety & Security Products 01.2009 The stored images can be tran sferred to t he FTP server when the n etwork status or other troubles are resolv ed. Function ON/OFF: Select ON to active SD card FTP back up function. Accumulation Cycle: Set a time interval in secon ds for images to be stored. [...]

Configuration 41 Siemens Building Technologies Fire Safety & Security Products 01.2009 z Scheduled Recording Determine the recording condition: STOP, all day, schedul e 1 or schedule 2 from the recording schedule table for all days from Monday to Sunday. z Recording by Alarm Configure "Alarm input setting" first. Then select the recor[...]

Configuration 42 Siemens Building Technologies Fire Safety & Security Products 01.2009 – Recording cycle Set a time interval for network recording. 1, 25, 10, 30, 60, 90, 120 s can be selected. 2. Click the Save button under the items. Î Changes are saved. NOTE Setting the overwrite mode to ON deletes files, beginning with old files. If impo[...]

Configuration 43 Siemens Building Technologies Fire Safety & Security Products 01.2009 Condition settings for sending e-mail by schedule Setup E-mail condition to Schedule. z Subject – input your subject title for sending e-mail z Message – input the alarm message as a notification z Attach Image – attach image files to your e-mail notifi[...]

Configuration 44 Siemens Building Technologies Fire Safety & Security Products 01.2009 Mail to Address List You can send e-mails to multiple users whe n schedule, alarm in, or motion detection occurred.[...]

Configuration 45 Siemens Building Technologies Fire Safety & Security Products 01.2009 7.5.4 NAS recording This is a method to store data on a network-based storage d evice. 3. Choose reco rd condition: Select the condition for NAS recordin g: recording by Schedule, Alarm or Motion to trigger the recording session. If Schedule mode is selected,[...]

Configuration 46 Siemens Building Technologies Fire Safety & Security Products 01.2009 z Scheduled Recording Determine the recording condition: STOP, all day, schedul e 1 or schedule 2 from the recording schedule table for all days from Monday to Sunday. z Recording by Alarm Configure "Alarm input setting" first. Then select the recor[...]

Configuration 47 Siemens Building Technologies Fire Safety & Security Products 01.2009 7.6 Audio You can set up your audio settings by enablin g audio input and output. Audio input z Audio Input: ON: The external microphone input or int egrated microphone is active OFF: The external microphone input or integrated microphone i s deactivated. z A[...]

Configuration 48 Siemens Building Technologies Fire Safety & Security Products 01.2009 7.7 Date/Time z Display Check “ON” to displ ay date/time on screen; the position and colour can be set on the camera OSD menu. z Synchronization mode – Manual: Input the date and time to set up system time. – NTP: You can also enable Net work Time Pro[...]

Configuration 49 Siemens Building Technologies Fire Safety & Security Products 01.2009 7.8 Access protection[...]

Configuration 50 Siemens Building Technologies Fire Safety & Security Products 01.2009 7.8.1 Administrator Administrator Functions Select Administrator in the Configuration menu. Y ou can set up system password, user language and logoff time. Password The default setting for system Admin ID and password is: z User ID: admin z Password: admin Yo[...]

Configuration 51 Siemens Building Technologies Fire Safety & Security Products 01.2009 7.9 Firewall 7.9.1 IP Adress Filter Enter the IP addresses which are to be p roces sed by the firewall system into the IP address field. Up to 10 addresses can b e set. Enable the IP address which is going to be pro cessed by the firewall filter. Choose Allow[...]

Configuration 52 Siemens Building Technologies Fire Safety & Security Products 01.2009 7.9.3 Forbidden Protocol ICMP or UDP protocol can be rejected by firewall if assigned. 7.10 System 7.10.1 Setting CGI-Lock is a system security setting. It means you can activate or deactivate the login data for the CGI-commands. If you se t ON, you alway s h[...]

Configuration 53 Siemens Building Technologies Fire Safety & Security Products 01.2009 7.10.2 Update You can update system firmware once t he upd ate file is available. It is the customer's respo nsibility to update firmware. All camera motions wil l shut down during firmware update. Close a ny other sc reens before starting a firmware upd[...]

Configuration 54 Siemens Building Technologies Fire Safety & Security Products 01.2009 7.10.4 Temperature There are two display types for temperature. The internal temp erature of the camera is displayed. If a temperature notification interval has been set an e -mail notice will be delivered con tinuously. If the not ification interval is set t[...]

Configuration 55 Siemens Building Technologies Fire Safety & Security Products 01.2009 7.11 Log Event Log Select Log in the Configuration menu. You can click the icons on the bottom to see and process the log s, such as: “display all logs”, “display syst em logs”, “display user logs”…. 7.12 Notice This dialog shows all licenses in[...]

Utility program application 56 Siemens Building Technologies Fire Safety & Security Products 01.2009 8 Utility program application 8.1 NAS player setup Playing back NAS file This application is found on the CD incl uded in the delivery. 1. Execute NAS record setup first. 2. Click on the cross cursor button and choose the p ath of the NAS file t[...]

Utility program application 57 Siemens Building Technologies Fire Safety & Security Products 01.2009 8.3 Firmware update setup This application is found on the CD incl uded in the d elivery. You can update multi- network cam eras synchro nously. Perform firmware update in the follo w ing sequence 1. Execute firmware update setup first. 2. Selec[...]

Maintenance 58 Siemens Building Technologies Fire Safety & Security Products 01.2009 9 Maintenance Defective modules sho uld be sent to the nearest Siemens office to be forwarde d to the service centre. 10 Disposal All electrical and electroni c products should be disp osed of separately from the municipal waste stream via designated collection[...]

Keyword index 59 Siemens Building Technologies Fire Safety & Security Products 01.2009 11 Keyword index A Access protection 49 Administrator 50 Advanced user 50 Alarm 10, 34 Alarm in terminal 12, 13 Alarm out terminal 12, 13 Audio 10, 47 Audio Event 36 Audio record 56 Authentication 42 Auto Gain Control 29 AWB 30 B Back Light Compensation 30 Ba[...]

Keyword index 60 Siemens Building Technologies Fire Safety & Security Products 01.2009 O Operating humidity 10 Operating temperature 10 Ordering Data 11 OSD settings 33 Overwrite 40 P Package Contents 11 Panning range 10 Picture Flip 30 Picture Mirror 30 Power IN connector 12, 13 Preset image 29 Primary DNS 27 Q Quicktime 26 R Reset button 12, [...]

[...]

Issued by Siemens Building Technologies Fire & Security Products GmbH & Co. oHG D-76181 Karlsruhe www.buildingtechnologies.siemens.com © 2009 Copyright by Siemens Building Technologies Data and design subject to change without notice. Supply subject to availability. Document no. A6V10236128 Edition 15.01.2009[...]