Smeg PGF95BE-2 manuale d’uso

Summary 1 INSTRUCTIONS FOR SAFE AND PROPER USE _______________ 21 2 POSITIONING OF THE HOB _______________________________ 23 3 ADJUSTMENT TO DIFFERENT TYPES OF GAS _______________ 30 4 FINAL OPERATIONS _____________________________________ 32 5 USING THE HOB ________________________________________ 33 6 CLEANING AND MAINTENANCE ___________________[...]

Introduction 1 INSTR UCTIONS FOR SAFE AND PR OPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS EN TIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE HOB. ALSO KEEP THE SERIES OF NOZZLES SUPPLIED. INSTALLATI[...]

Introduction THE APPLIANCE DATA PLATE, WITH TECHNICAL DATA, REGISTRATION NUMBER AND BRAND NAME, IS POSITIONED AT A VISIBLE POINT UNDER THE SAFETY COVER. THE DATA PLATE ON THE PROTECTIVE COVER MUST NEVER BE REMOVED . DO NOT PUT PANS WITHOUT PERFECTLY PERFECTLY SMOOTH AND FLAT BOTTOMS ON THE HOB PANSTAND GRIDS. DO NOT USE COOKING RECEPTACLES THAT EXT[...]

Instructions for the installer 23 2 POSITIONING OF THE HOB The following operation requires buildi ng and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminat ed wood, as long as they are heat- resistant (T 90°C). 2.1 Attachment[...]

Instructions for the installer 4) 24 2.2 Attachment to support structure, flush-mounting model Create an opening with the dimensions shown in the figure in the work surface, observing a minimum distance of 50 mm from the rear edge. 1) The lower part of the protective cover must be fully accessible when the appliance is installed. This appliance can[...]

Instructions for the installer 25 4) Mill to this depth for laminated worktops of less than 3mm thickness. Apply a layer of “waterproof pr imer” to the milled surface. Important: Other types of installation will only be possible under th e manufacturer's supervision. Overall dimensions: location of gas and electrical connection points (all[...]

Instructions for the installer 26 The appliance is equipped with 4 supplem entary brackets for levelling if necessary (see detail B , fig. 5). The following figures show how to use the brackets. IMPORTANT: when installing the app liance above a cupboard, a dividing shelf, as shown above, must be installed. If installed above an under-bench ov en, t[...]

Instructions for the installer 27 2.3 Electrical connection Make sure that the voltage and capacit y of the power supply cable conform to the data shown on the plate loca ted under the protective cover. Do not remove this plat e for any reason . The power supply cable plug and the wa ll socket must be of the same type and conform to the current ele[...]

Instructions for the installer 28 2.4 Ventilation requirements The appliance may be installed only in rooms with permanent ventilation, as required by standard r egulations in force. T he room in which the appliance is installed must have sufficient air flow to satisfy the requirements of normal gas combus tion and of necessary air exchange in the [...]

Instructions for the installer 29 2.6 Gas connection Connection to the gas mains may be made with a rigid copper pipe or with a flexible pipe conforming to the prov isions defined by standard regulations in force. After connection operations, check for leaks using a soapy solution. The hob has been inspected for G20 natural gas (2H) at a pressure o[...]

Instructions for the installer 30 3 ADJUSTMENT T O DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, unplug th e appliance from the mains. The hob is set for natural gas G20 (2H) at a pressure of 20 mbar. In the case of functioning with other types of gas the burner nozzles must be changed and the minimum flame adjust ed on[...]

Instructions for the installer 31 3.2 Burner and nozzle characteristics table Burner Rated heating capacity (kW) LPG – G30/G31 30/37 mbar Nozzle diameter 1/100 mm By-pass mm 1/100 Reduced flow rate (W) Flow rate g/h G30 Flow rate g/h G31 Auxiliary (1) 1.05 50 30(*) 28 (**) 350 76 75 Semi rapid (2) 1.75 65 33(*) 32 (**) 450 130 128 Rapid (3) 2.3 7[...]

Instructions for the installer 32 4 FINAL OPERA TIONS After carrying out the above adjustments, remount in reverse order to the instructions given in paragraph “3.1 Replacement of nozzles on the hob”. After adjustment to a different kind of gas from the one for which the appliance has been tested, replac e the plate inside the storage compartme[...]

Instructions for the user 5 USING THE HOB 5.1 Ignition of the burners Before turning on the burners, make su re that the flame-spreader crowns and respective caps are properly fi tted in their housings. Ensure the flame-spreader holes A are aligned with the ignition plugs and the thermocouples. Panstand grid B , available upon request, is intended [...]

Instructions for the user 34 If the burners turn off accidentally, a safety device will trip after about 20 seconds to cut off gas flow (even with the gas tap open). 5.2 Practical advice for using the burners For better use of the burners and lowe r gas consumption, use covered cooking receptacles that have a flat, smooth bottom and are proportiona[...]

Instructions for the user 6 CLEANING AND MAINTENANCE Before any intervention, disconnect the appliance from the mains. 6.1 Cleaning the stainless steel To keep stainless steel in good c ondition it should be cleaned regularly after use. Let it cool first. 6.1.1 Routine daily cleaning To clean and preserve the stainl ess steel surfaces, always use o[...]

Instructions for the user 36 In models equipped with pan stands, fit as shown in the figure, taking care to position them exactly as s hown. Refer to the enlarged details in the figure below for guidance.[...]