Socket Mobile IB810 manuale d’uso

IB810 Full - Size Socket 478 Pentium 4 Intel 845 CPU Card USER ’ S MANUAL Version 1.0A[...]

ii IB810User ’ s Manual Acknowledgments Award is a registered trademark of Award Software International, Inc. PS/2 is a trademark of International Business Machines Corporation. Intel and Pentium 4 are registered trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation. Winbond is a registered trademar[...]

IB810 User ’ s Manual iii Table of Contents Introduction ........................................................ 1 Product Description .......................................................... 1 Checklist ........................................................................... 2 Spe cifications ...............................................[...]

iv IB810 User ’ s Manual This page is intentionally left blank.[...]

INTRODUCTION IB810 User ’ s Manual 1 Introduction Pr oduct Description The IB810 Pentium 4 Full Size PICMG CPU Card incorporates the Intel ® advanced 845 Chipset Memory Controller hub and supports 478 - pin Intel Pentium 4 processors of 1.3GHz and up to 2GHz. This CPU card represents the perfect choice for thos e who want superior performance fo[...]

INTRODUCTION 2 IB810 User ’ s Manual Checklist Your IB810 package should include the items listed below. • The IB810 Industrial CPU Card • This User’s Manual • 1 IDE Ribbon Cable • 1 Floppy Ribbon Connector • 2 Serial Port Ribbon Cable and 1 Parallel Port Attached to a Mounting Bracket • 1 Y - Cable supporting a PS/2 Keyboard and a [...]

INTRODUCTION IB810 User ’ s Manual 3 Specifications Processor Supported Socket 478 support Intel Pentium 4 1.3GHz~2GHz, 400MHz B us Speed Chipset Intel 845 Chipset BIOS Award BIOS Supports ACPI System Memory 2x DDR memory sockets support up to 2GB capacity PC200/PC266 supported LPC I/O Chipset ITE IT8712 (keyboard controller is built - in) I/O Fe[...]

INTRODUCTION 4 IB810 User ’ s Manual Board Dimensions[...]

INSTALLATIONS IB810 User ’ s Manual 5 Installations This section provides information on how to use the jumpers and connectors on the IB810 in order to set up a workable system. The topics covered are: Installing the CPU ............................................................. 6 ATX Power Installation ........................................[...]

INSTALLATIONS 6 IB810 User ’ s Manual Installing the CPU The IB810 CPU Ca rd supports a Socket 478 processor socket for Intel Pentium 4 processors. The Socket 478 processor socket comes with a lever to secure the processor. Raise this lever to about a 90 ° angle to allow the insertion of the processor. Place the processor into the socket by maki[...]

INSTALLATIONS IB810 User ’ s Manual 7 ATX Power Installation Power is provided to the IB810 CPU card with the J2 and J12 ATX power connectors. Please note that the J12 external ATX power connector should be connected to the backplane for IB810 to fun ction. J12 is located below the IDE connector. Please refer to the figure below. MicroPCI Daughte[...]

INSTALLATIONS 8 IB810 User ’ s Manual Installing the Memory The IB810 CPU Card supports two DDR memory sockets for a maximum total memory of 2GB in DDR memory type. The memory module capacities supported are 64MB, 128MB, 256MB, 512MB and 1GB. Installing and Re moving Memory Modules To install the DDR modules, locate the memory slot on the CPU car[...]

INSTALLATIONS IB810 User ’ s Manual 9 Sett ing the Jumpers Jumpers are used on IB810 to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the connectors on IB810 a nd their respective functions. Jumper Locations o[...]

INSTALLATIONS 10 IB810 User ’ s Manual Jumper Locations on IB810 JP10, JP11, JP12, JP13, JP14: CRT VGA Signal Select JP2, JP3, JP4: RS232/422/485 (COM2) Selection JP1: DiskOnChip Address Select JP8: LVDS Panel Power Select JP7: Clear CMOS Contents SW1: LVDS Resolution Select[...]

INSTALLATIONS IB810 User ’ s Manual 11 Configuring the CPU Frequency The IB810 CPU card does not provide DIP switches to configure the processor speed (CPU frequency). Howe ver, the processor speed can be automatically detected by the system. JP1: DiskOnChip Address Select JP1 Address D0000 - D7FFF D8000 - DFFFF (default) JP2, JP3, JP4: RS232/422[...]

INSTALLATIONS 12 IB810 User ’ s Manual JP7: Clear CMOS Contents Use JP7, a 3 - pin header, to clear the CMOS contents. Note that the ATX - power connector should be disconnected from the CPU card before clearing CMOS. JP7 Setting Function Pin 1 - 2 Short/Closed Normal Pin 2 - 3 Short/Closed Clear CMOS JP8: LVDS Panel Power Select JP8 Pow er 3.3V [...]

INSTALLATIONS IB810 User ’ s Manual 13 This page was intentionally left blank.[...]

INSTALLATIONS 14 IB810 User ’ s Manual [ Connectors on IB810 The connectors on IB810 allows you to connect external devices such as keyboard, floppy disk drives, hard disk drives, printers, etc. The following table lists the connectors on IB810 and their re spective functions. Connector Locations on IB810 .........................................[...]

INSTALLATIONS IB810 User ’ s Manual 15 Connector Locations on IB810 J27: 2nd RJ45 Connector J26: VGA CRT Connector J25: Primary RJ45 Connector J23: PS/2 KB and Mouse Conn. J22: External PS/2 KB and Mouse J21: IrDA Connector J8, J9: COM1/2 Serial Port J14: External Audio Connector J5: Parallel Port Connector J20: Smart Card Reader Interface J19: U[...]

INSTALLATIONS 16 IB810 User ’ s Manual J1: System Function Connector J1 provides connectors for system indicators that provide light indication of the computer activities a nd switches to change the computer status. J1 is a 20 - pin header that provides interfaces for the following functions. Hard Disk Drive LED Reset Switch Turbo LED Connector A[...]

INSTALLATIONS IB810 User ’ s Manual 17 SMI/Hardware Switch: Pins 6 and 16 This connector supports the "Green Switch" on the control panel, which, when pressed, will force the system into the power - saving mode immediately. Pin # Signal Name 6 Sleep 16 Ground ATX Power ON Switch: Pins 7 and 17 T his 2 - pin connector is an “ATX Power [...]

INSTALLATIONS 18 IB810 User ’ s Manual Hard Disk Drive LED Conne ctor: Pins 10 and 20 This connector connects to the hard drive activity LED on control panel. This LED will flash when the HDD is being accessed. Pin # Signal Name 10 HDD Active 20 5V J2: ATX 12V/+12V Power Connector Pin # Signal Name 1 Ground 2 Ground 3 +12V 4 +12V IDE1, IDE2: EIDE[...]

INSTALLATIONS IB810 User ’ s Manual 19 IDE2: Secondary IDE Connector Signal Name Pin # Pin # Signal Name Reset IDE 1 2 Ground Host data 7 3 4 Host data 8 Host data 6 5 6 Host data 9 Host data 5 7 8 Host data 10 Host data 4 9 10 Host data 11 Host data 3 11 12 Host data 12 Host data 2 13 14 Host data 13 Host data 1 15 16 Host data 14 Host data 0 17[...]

INSTALLATIONS 20 IB810 User ’ s Manual FAN3: Auxiliary Fan Power Connector FAN3 is a 3 - pin header for a 12V fan. Pin # Signal Name 1 Ground 2 +12V 3 Rotat ion detection J4: Floppy Drive Connector J4 is a 34 - pin header and will support up to 2.88MB floppy drives. Signal Name Pin # Pin # Signal Name Ground 1 2 RM/LC Ground 3 4 No connect Ground[...]

INSTALLATIONS IB810 User ’ s Manual 21 J5: Parallel Port Connector The following table describes the pin out assignments of this connector. Signal Name Pin # Pin # Signal Name Line printer strobe 1 14 AutoFeed PD0, parallel data 0 2 15 Error PD1, parallel data 1 3 16 Initialize PD2, parallel data 2 4 17 Select PD3, parallel data 3 5 18 Ground PD4[...]

INSTALLATIONS 22 IB810 User ’ s Manual J8, J9: COM1, COM2 Serial Port J8 and J9, both 10 - pin headers, are the onboard serial port connectors. Pin # Signal Name RS - 232 RS - 422 RS - 485 1 DCD TX - DATA - 2 RX TX+ DATA+ 3 TX RX+ NC 4 DTR RX - NC 5 GND GND GND 6 DSR RTS - NC 7 RTS RTS+ NC 8 CTS CTS+ NC 9 RI CTS - NC J8 fixed as RS - 232 J9 Confi[...]

INSTALLATIONS IB810 User ’ s Manual 23 J11, J16: LVDS Connectors (2nd channel, 1st channel) The LVDS connectors are composed of the first channel (J16) and second channel (J11) to support 24 - bit or 48 - bit. Signal Name Pin # Pin # Signal Name TX0 - 2 1 TX0+ Ground 4 3 Ground TX1 - 6 5 TX1+ 5V/3.3V 8 7 Ground TX3 - 10 9 TX3+ TX2 - 12 11 TX2+ Gr[...]

INSTALLATIONS 24 IB810 User ’ s Manual J12: External ATX Power Connector Pin # Signal Name 1 Ground 2 PS - ON (soft on/off) 3 5VSB (Standb y +5V) J14: External Audio Connector J14 is a 12 - pin header that is used to connect to the ID120 daughter card that integrates jacks for Line In, Line Out and Speaker. Signal Name Pin # Pin # Signal Name LIN[...]

INSTALLATIONS IB810 User ’ s Manual 25 J18, J19: USB Connectors The following table shows the pin outs of the USB pin headers connectors. Overa ll, the two pin headers support four USB ports. Signal Name Pin Pin Signal Name Vcc 1 5 Ground USB0 - 2 6 USB1+ USB0+ 3 7 USB1 - J18 Ground 4 8 Vcc Signal Name Pin Pin Sig nal Name Vcc 1 5 Ground USB2 - 2[...]

INSTALLATIONS 26 IB810 User ’ s Manual J21: IrD A Connector J21 is used for an optional IrDA connector for wireless communication. Pin # Signal Name 1 +5V 2 No connect 3 Ir RX 4 Ground 5 Ir TX J22: External PS/2 Keyboard and Mouse Connector Pin # Signal Name 1 Mouse data 2 KB data 3 Ground 4 Vcc 5 Mouse Clock 6 KB Clock Please take note of the pi[...]

INSTALLATIONS IB810 User ’ s Manual 27 J23: PS/2 Keyboard and Mouse Connector J23 uses a Y - cable with dual D - connectors for a PS/2 keyboar d and a PS/2 mouse. Pin # Signal Name 1 Mouse data 2 Keyboard data 3 Ground 4 Vcc 5 Mouse Clock J12 6 Keyboard Clock J25, J27: Primary and Secondary RJ45 Connector J25 and J27 are the primary RJ - 45 and s[...]

BIOS SETUP 28 IB810 User ’ s Manual BIOS Setup This chapter describes the different settings available in the Award BIOS that comes with the CPU card. The topics covered in this chapter are as follows: BIOS Introduction ........................................................................ 29 BIOS Setup .........................................[...]

BIOS SETUP IB810 User ’ s Manual 29 BIOS Introduction The Award BIOS (Basic Input/Output System) installed in your computer system’s ROM supports Intel Pentium 4 processors. The BIOS provides critical low - leve l support for a standard device such as disk drives, serial ports and parallel ports. It also adds virus and password protection as we[...]

BIOS SETUP 30 IB810 User ’ s Manual CMOS Setup Utility – Copyright © 1984 - 2001 Award Software Standard CMOS Features Frequency/Voltage Control Advanced BIOS Features Load Fail - Safe Defaults Advanced Chipset Features Load Optimized Defaults Integr ated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP/PCI Conf[...]

BIOS SETUP IB810 User ’ s Manual 31 Standard CMOS Setup “Standard CMOS Setup” choice allows you to record some basic hardware configurations in your computer system and set the system clock and error handling. If the CPU card is already installed in a working system, you wi ll not need to select this option. You will need to run the Standard [...]

BIOS SETUP 32 IB810 User ’ s Manual Time The time format is: Hour : 00 to 23 Minute : 00 to 59 Second : 00 to 59 To set the time, highlight the “Time” field and use the <PgUp>/ <PgDn> or +/ - keys to set the current time. IDE Primary HDDs / IDE Secondary HDDs The onboard PCI IDE connectors provide Primary and Secondary channels fo[...]

BIOS SETUP IB810 User ’ s Manual 33 Video Thi s field selects the type of video display card installed in your system. You can choose the following video display cards: EGA/VGA For EGA, VGA, SEGA, SVGA or PGA monitor adapters. (default) CGA 40 Power up in 40 column mode. CGA 80 Power up in 80 column mode. MONO For Hercules or MDA adapters. Halt O[...]

BIOS SETUP 34 IB810 User ’ s Manual Advanced BIOS Features This section allows you to configure and improve your system and allows you to set up some system features according to your preference. CMOS Setup Utility – Copyright © 1984 - 2001 Award Software Advanced BIOS Features Virus Warning Disabled ITEM HELP CPU L1 and L2 Cache Enabled Menu [...]

BIOS SETUP IB810 User ’ s Manual 35 First/Second/Third Boot Device These fields deter mine the drive that the system searches first for an operating system. The options available include Floppy , LS/ZIP , HDD - 0 , SCSI , CDROM , HDD - 1 , HDD - 2 , HDD - 3 , LAN and Disable . Boot Other Device These fields allow the system to search for an opera[...]

BIOS SETUP 36 IB810 User ’ s Manual Security Option This field allows you to limit access to the System and Setup. The default value is Setup . When you select System, the system prompts for the User Password every time you boot up. When you select Setup, the system always boots up and prompts for the Supervisor Password only when the Setup utili[...]

BIOS SETUP IB810 User ’ s Manual 37 Advanced Chipset Features This Setup menu controls the configuration of the chipset. CMOS Setup Utility – Copyright © 1984 - 2001 Award Software Advanced Chipset Features DRAM Timing Selectable By SPD ITEM HELP CAS Latency Time 2.5 Menu Level Active to Precharge Delay 7 DRAM RAS# to CAS# Delay 3 DRAM RAS# Pr[...]

BIOS SETUP 38 IB810 User ’ s Manual DRAM Data Integrity Mode This BIOS setting is used to configure your RAM's data integrity mode. ECC stands for Error Checking and Correction and it should only be used if you are using 72 - bit ECC RAM. This will enable the system to detect and correct single - bit errors. It will also detect double - bit [...]

BIOS SETUP IB810 User ’ s Manual 39 Delay Prior to Thermal This field activates the CPU thermal function after the systems boots for the set number of minutes. The options are 16Min and 64Min . AGP Aperture Size The field sets aperture size of the graphics. The a perture is a portion of the PCI memory address range dedicated for graphics memory a[...]

BIOS SETUP 40 IB810 User ’ s Manual Integrated Peripherals This section sets configurations for your hard disk and other integrated peripherals. CMOS Setup Utility – Copyright © 1984 - 2001 Award Software Integrated Peripherals On - Chip Primary PCI ID E Enabled ITEM HELP IDE Primary Master PIO Auto Menu Level IDE Primary Slave PIO Auto IDE Pr[...]

BIOS SETUP IB810 User ’ s Manual 41 IDE Primary/Secondary Master/Slave UDMA These fields allow your system to improve disk I/O th roughput to 33Mb/sec with the Ultra DMA/33 feature. The options are Auto and Disabled . USB Controller The options for this field are Enabled and Disabled . By default, this field is set to Enabled . USB Keyboard Suppo[...]

BIOS SETUP 42 IB810 User ’ s Manual UART Mode Select This field determines the UART 2 mode in your computer. The default value is Normal . Other options include IrDA and ASKIR . UR2 Duplex Mode This field allows you to choo se between Half Duplex and Full Duplex mode. Parallel Port Mode This field allows you to determine parallel port mode functi[...]

BIOS SETUP IB810 User ’ s Manual 43 Power Management Setup The Power Management Setup allows you to save energy of your system effectively. CMOS Setup Utility – Copyright © 1984 - 2001 Award Software Power Management Setup Power - Supply Type ATX ITEM HELP ACPI Function Enabled Menu Level ACPI Suspend Type SI (POS) Power Management User Define[...]

BIOS SETUP 44 IB810 User ’ s Manual Power Management This field allows you to select the type of power saving management modes. There are four se lections for Power Management. Min. Power Saving Minimum power management Max. Power Saving Maximum power management. User Define Each of the ranges is from 1 min. to 1hr. Except for HDD Power Down whic[...]

BIOS SETUP IB810 User ’ s Manual 45 Video Off Method This field defines the Video Off features. There are three options. V/H SYNC + Blank Default setting, blank the screen and turn off vertical and horizontal scanning. DPMS Allows BIOS to control the video display. Blank Screen Writes blanks to the video bu ffer. Video Off In Suspend When enabled[...]

BIOS SETUP 46 IB810 User ’ s Manual Reload Glob al Timer Events The HDD, FDD, COM, LPT Ports, and PCI PIRQ are I/O events which can prevent the system from entering a power saving mode or can awaken the system from such a mode. When an I/O device wants to gain the attention of the operating system, it s ignals this by causing an IRQ to occur. Whe[...]

BIOS SETUP IB810 User ’ s Manual 47 PNP/PCI Configurations This option configures the PCI bus system. All PCI bus systems on the system use INT#, thus all installed PCI cards must be set to this value. CMOS Setup Utility – Copyright © 1984 - 2001 Award Software PnP/PCI Configurations PNP OS Install No ITEM HELP Reset Configuration Data Disable[...]

BIOS SETUP 48 IB810 User ’ s Manual PC Health Status This section shows the parameters in determining the PC Health Status. These parameters include temperatures, fan speeds and voltages. CMOS Setup Utility – Copyright © 1984 - 2001 Award Software PC Health Status Shutdown Temperature Disabled ITEM HELP Vcore (V) 1.63V +1.8(V) 1.79V VCC3(V) 3.[...]

BIOS SETUP IB810 User ’ s Manual 49 Frequency/Voltage Control This section shows the user how to configure the processor frequency. CMOS Setup Utility – Copyright © 1984 - 2001 Award Software Frequency/Voltage Control CPU Clock Ratio 10X ITEM HELP Auto Detect PCI Clk Disabled Spread Spectrum Disabled Menu Level CPU Clock Ratio The CPU Ratio, a[...]

BIOS SETUP 50 IB810 User ’ s Manual Load Fail - Safe Defaults This option allows you to load the troubleshooting default values perman ently stored in the BIOS ROM. These default settings are non - optimal and disable all high - performance features. Load Setup Defaults This option allows you to load the default values to your system configuratio[...]

DRIVERS INSTALLATION IB810 User ’ s Manual 51 Drivers Installation This section describes the installation procedures for software and drivers under the Windows 98, Windows NT 4.0 and Windows 2000. The software and drivers are included with the C PU card. If you find the items missing, please contact the vendor where you made the purchase. The co[...]

DRIVERS INSTALLATION 52 IB810 User ’ s Manual Intel Software Installation Utility The In tel Chipset Software Installation Utility will enable Plug & Play I N F support for Intel chipset components. Follow the instructions below to complete the installation under Windows 98 and Windows 2000. 1. Insert the CD that comes with the CPU card and t[...]

DRIVERS INSTALLATION IB810 User ’ s Manual 53 3. When the Welcome screen appears, click Next to continue. 4. Click Yes to accept the software license agre ement and proceed with the installation process.[...]

DRIVERS INSTALLATION 54 IB810 User ’ s Manual 5. On Readme Information screen, click Next to continue the installation. 6. The Setup process is now complete. Click Finish to restart the computer and for changes to take effect. When the compu ter has restarted, the system will be able to find some devices. Restart your computer when prompted.[...]

DRIVERS INSTALLATION IB810 User ’ s Manual 55 Intel Ultra ATA Storage Driver Intel Ultra ATA Storage Driver Follow the steps below to install Intel Ultra ATA Storage Driver with the InstallShie ld Wizard under Windows 98, Windows 2000 and Windows NT 4.0. 1. Insert the CD that comes with the CPU card and the screen below would appear. Click Intel [...]

DRIVERS INSTALLATION 56 IB810 User ’ s Manual 3. The Welco me screen of the Install Shield Wizard for Intel Ultra ATA Storage Driver appears. To continue, click Next. 4. Click Yes to accept the software license agreement and proceed with the installation process.[...]

DRIVERS INSTALLATION IB810 User ’ s Manual 57 5. You are now required to Select the folder where Setup will install files. Click Next to accept the default folder or click Browse to configure the location. 6. You are now asked to select a program folder. Click Next to accept the default program folder or enter the folder name you pre fer.[...]

DRIVERS INSTALLATION 58 IB810 User ’ s Manual 7. The InstallShield Wizard has completed installation. Click Finish for the computer to restart and changes to take effect. Windows 98 Drivers Installation ATI M6 VGA Driver Installation Follow the steps below to install the ATI Mobilit y Radeon M6 Graphics Driver under Windows 98. 1. Insert the CD t[...]

DRIVERS INSTALLATION IB810 User ’ s Manual 59 2. When the Welcome screen appe ars, click Next to continue. 3. Click Yes to accept the software license agreement and proceed with the installation process.[...]

DRIVERS INSTALLATION 60 IB810 User ’ s Manual 4. In the Select Components window, click on the Express installation method, then click Yes to start file copying . 5. The Setup program has now completed installation. Click Finish for the computer to restart and changes to take effect.[...]

DRIVERS INSTALLATION IB810 User ’ s Manual 61 SigmaTel AC97 Audio Drivers Follow the steps below to install SigmaTel AC97 Audio Drivers on your system under Windows 98 . 1. Insert the CD that comes with the CPU card and the screen below would appear. Click Intel 845 Chipset Family Driver. 2. Click SigmaTel AC97 Audio Driver.[...]

DRIVERS INSTALLATION 62 IB810 User ’ s Manual 3. The Welcome screen of the SigmaTel AC97 Audio Driver Setup program appears. To c ontinue, click Next. 4. Click Yes to accept the software license agreement and proceed with the installation process.[...]

DRIVERS INSTALLATION IB810 User ’ s Manual 63 5. Select Install and click Next to install SigmaTel AC97 Audio Drivers on your system. 6. The Setup program has now comp leted installation. Click Finish for the computer to restart and changes to take effect. 7. After the system has restarted, a screen would appear saying it was able to find the dev[...]

DRIVERS INSTALLATION 64 IB810 User ’ s Manual 8. Now c lick Select to “Search for the best river for your device (Recommended).” Click Next, then click Select to “specify a location”. Now enter the path as “d: intel i845 sound win98 driver wdm” (This is assuming drive D: is your CD - ROM drive. 9. Now click Nex t and Next [...]

DRIVERS INSTALLATION IB810 User ’ s Manual 65 Windows NT 4.0 Drivers Installation ATI M6 VGA Driver Installation To install the ATI Radeon M6 Graphics drivers for Windows NT 4.0, please follow the same procedure as shown in the ATI M6 VGA Driver Installation for Windows 98 in the previous section. SigmaTel AC97 Audio Drivers Follow the steps belo[...]

DRIVERS INSTALLATION 66 IB810 User ’ s Manual 2. Click SigmaTel AC97 Audio Driver. 3. The Welcome screen of the SigmaTel AC97 A udio Driver Setup program appears. To continue, click Next.[...]

DRIVERS INSTALLATION IB810 User ’ s Manual 67 4. Click Yes to accept the software license agreement and proceed with the installation process. 5. Select Install and click Next to install SigmaTel AC97 Audio Drivers on your system.[...]

DRIVERS INSTALLATION 68 IB810 User ’ s Manual 6. The Setup program has now completed installation. Click Finish for the computer to restart and changes to take effect. 7. After the system has restarted, a screen would appear showing some installation information. Restart the system when prom pted to complete the audio driver installation. PCI Eth[...]

DRIVERS INSTALLATION IB810 User ’ s Manual 69 Windows 2000 Drivers Install ation ATI M6 VGA Driver Installation To install the ATI Radeon M6 Graphics drivers for Windows NT 4.0, please follow the same procedure as shown in the ATI M6 VGA Driver Installation for Windows 98 in the previous section. SigmaTel AC97 Audio Drivers Fo llow the steps belo[...]

DRIVERS INSTALLATION 70 IB810 User ’ s Manual 4. Click Yes to accept the software license agreement and proceed with the installation process. 5. Select Install and click Next to insta ll SigmaTel AC97 Audio Drivers on your system.[...]

DRIVERS INSTALLATION IB810 User ’ s Manual 71 6. A window appears indicating that the software to be installed does not contain a Microsoft digital signature. Click Yes to continue the installation process. 7. The Setup program has now complet ed installation. Click Finish for the computer to restart and changes to take effect.[...]

DRIVERS INSTALLATION 72 IB810 User ’ s Manual PCI Ethernet Drivers The first thing to do to install the Ethernet drivers is to create a floppy diskette that would contain the drivers. Follow the steps below. 1. Insert the CD that comes with your IB810. In the initial screen, click on LAN Card, then click on Intel PRO LAN Drivers. The following fi[...]

APPENDIX IB810 User ’ s Manual 73 Appendix A. I/O Port Address Map B. Inter rupt Request Lines (IRQ) A. I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port addresses which also becomes the identity of the device. The following table lists the I/O port addresses used. Address Device Descript ion 000h - 01Fh DMA [...]

APPENDIX 74 IB810 User ’ s Manual B. Interrupt Request Lines (IRQ) Peripheral devices use interrupt request lines to not ify CPU for the service required. The following table shows the IRQ used by the devices on board. Level Function IRQ0 System Timer Output IRQ1 Keyboard IRQ2 Interrupt Cascade IRQ3 Serial Port #2 IRQ4 Serial Port #1 IRQ5 Reserve[...]