Sony VPL-VW100 manuale d’uso

VIDEO PROJECTOR VPL-VW100 PROTOCOL MANUAL 1st Edition[...]

VPL-VW100 ! W ARNING This manual is intended for qualified service personnel only . T o reduce the risk of electric shock, fire or injury , do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! W ARNUNG Die Anleitung ist nur für [...]

1 VPL-VW100 Table of Contents 1. Introduction 2. RS-232C 2-1. Communication Specifications .......................................... 1 2-2. Command Block Format .................................................... 2 2-3. Block Format ..................................................................... 3 2-4. Connection ...........................[...]

[...]

1 VPL-VW100 EVEN Parity ...... Total number of “1”s from D0 to D7 is an even number. 8 0 ...... Total number of “1”s from D0 to D7 is an odd number. 8 1 D4 D5 D6 D7 (MSB) (LSB) (EVEN) BIT PARITY STOP BIT START D3 D2 D1 D0 1. Introduction This protocol manual describes the basic configuration and basic operations of various commands used for[...]

2 VPL-VW100 2-2. Command Block Format The code from B0 to B7 as described below are transmitted. START CODE : 0xA9 B0 B1 B2 B4 B3 DATA ITEM NUMBER ACK / NAK ITEM NUMBER SET / GET ACK DUMMY DATA CHECK SUM END CODE : 0x9A DATA REPLY B5 B6 B7 Transmission from the Master side Reception in the Master side Reception in the Master side (With Data) B0 STA[...]

3 VPL-VW100 2-3. Block Format START CODE B0 B1 B2 B4 B3 DATA ITEM NUMBER SET / GET CHECK SUM END CODE B5 B6 B7 START CODE B0 B1 B2 B4 B3 DUMMY DATA ACK / NAK ACK CHECK SUM END CODE B5 B6 B7 START CODE B0 B1 B2 B4 B3 DATA ITEM NUMBER REPLY CHECK SUM END CODE B5 B6 B7 Transmission from the Master side Reception in the Master side Reception in the Mas[...]

4 VPL-VW100 2-5. Communication Procedure 2-5-1. Outline of Communication All communication between CONTROLLER (PC, etc.) and DEVICE (PROJECTOR) is performed by the command block format. Communication is started by the issue of a command at CONTROLLER and ended when the return data is sent to CONTROLLER after DEVICE receives the command. CONTROLLER [...]

5 VPL-VW100 2-6. Communication Rules . When sending a command from CONTROLLER, the return data from PROJECTOR should be re- ceived first before sending the next command. Even if the next command is sent before receiving the return data, since PROJECTOR will not be able to receive that command, it does not return a response to CONTROLLER. Consequent[...]

6 VPL-VW100 3. NETWORK This section describes the performance, operations and protocol to be used of advertisement and PJ Talk. 3-1. Advertisement The advertisement service is provided to facilitate development of a PC application that can automatically detect a projector on the network. This function is achieved by broadcasting the equipment infor[...]

7 VPL-VW100 3-2. PJ Talk The remote control service is provided that can control the projector from remote location via network. 3-2-1. Function This responds to the control command and requests for acquiring the status and information supplied from clients. Control request Enables the input to be selected and picture control to be adjusted. SIRCS [...]

8 VPL-VW100 3-3. SDAP Protocol This section describes the SDAP packet structure. Fig.1 Packet structure 1) Header The header consists of ID (16 bit), version (8 bit) and category (8 bits). Fig. 2 Header ID It is fixed to “ DA ” . Version This indicates the version number of protocol. It is fixed to 01h (version 1). Category Category number 0Ah [...]

9 VPL-VW100 3-4. SDCP Protocol This section describes the packet structure of version 2. Fig. 1 Packet structure 3-4-1. Format 3-4-1-1. Header The header consists of version (8 bits) and category (8 bits). Fig. 2 Header structure Version This indicates the version number of protocol. It is fixed to 02h (version 2). Category Category number 0Ah of t[...]

10 VPL-VW100 3-4-1-3. Command This section describes the format of the request command and the response command. (1) Request This section describes the format of the request command that is issued from the host PC to the projector. Community This is the same alphanumeric characters as those of community that is set in the projector to which request[...]

11 VPL-VW100 SET (00h) Item No. n Set Data (n byte) Request Item No. Data Length Data OK (01h) Item No. 0 3-4-1-4. SET Request The SET request is used to set a new value in the specified item. Details of the request and the response are described below. Request Response 3-4-1-5. GET Request The GET request is used to acquire the value of the specif[...]

12 VPL-VW100 3-4-2. Items Category Contents SET GET 00**h Used to control and to change the various setups. OO 01**h Used to acquire the status. O 03**h Used to reset memory. O 17**h Sircs (15 bit category) O 19**h Sircs (20 bit category) O 80**h Used to acquire equipment information. O 90**h Used to acquire network setup information. O 3-4-2-1. Mo[...]

13 VPL-VW100 3-4-2-3. Network Information Acquisition (90**h) Used to acquire the network setup information. Lower bytes Contents SET GET 00h MAC Address O 01h IP Address O 02h Subnet Mask O 03h Default Gateway O 04h DHCP O 0x9000 Mac Address 6 bytes 0x9001 IP Address 4 bytes 0x9002 Subnet Mask 4 bytes 0x9003 Default Mask 4 bytes 0x9004 DHCP 1 byte[...]

14 VPL-VW100 3-4-3. Error Code The error code list is shown below with a detailed description of each. Category Error Error Code Item Error (01**h) Invalid Item 01h Invalid Item Request 02h Invalid Length 03h Invalid Data 04h Short Data 11h Not Applicable Item 80h Community Error (02**h) Different Community 01h Request Error (10**h) Invalid Version[...]

15 VPL-VW100 3-4-3-1. Item Error This error occurs when the Item No. of a request is illegal or its data is illegal. The conditions for occur- rence of the respective errors are shown below. Invalid Item An unsupported Item No. is specified. Example 1: The unsupported category 0xA ** is specified. Example 2: The unsupported Item No. 0x8010 is speci[...]

16 VPL-VW100 3-4-3-3. Request Error This error occurs when header or command is illegal. The conditions of occurrence of the respective errors are shown below. Invalid Version The version of the header is other than 2. n When another version is supported, an error occurs in all versions other than the supported version. Invalid Category The categor[...]

17 VPL-VW100 3-4-3-5. Comm Error This is an error in communication with the main control microprocessor of the display. Timeout Reception data is not returned after data is sent. Check Sum Error A check sum error occurred in the main control microprocessor of the display. Framing Error A framing error occurred. Parity Error A parity error occurred.[...]

18 VPL-VW100 Appendix <Table 1> <Table 2> Remarks Item Number Data Item Upper byte Lower byte Data Upper byte Lower byte Input 00h 01h Video 00h 00h Set/Get S Video 00h 01h Input-A 00h 02h Component 00h 03h HDMI 00h 04h DVI 00h 05h Picture Mode 00h 02h Dynamic 00h 00h Standard 00h 01h Cinema 00h 02h User1 00h 03h User2 00h 04h User3 00h[...]

19 VPL-VW100 <Table 1> <Table 2> Remarks Item Number Data Item Upper byte Lower byte Data Upper byte Lower byte Wide Mode 00h 20h Full 00h 00h Set/Get Normal 00h 01h Wide Zoom 00h 02h Zoom 00h 03h Subtitle 00h 04h Gamma Correction 00h 22h Off 00h 00h Gamma 1 00h 01h Gamma 2 00h 02h Gamma 3 00h 03h OverScan 00h 23h Off 00h 00h On 00h 01h[...]

20 VPL-VW100 <Table 1> <Table 2> Remarks Item Number Data Item Upper byte Lower byte Data Upper byte Lower byte Status Error 01h 01h No Error 00h 00h Get only Lamp Error 00h 01h Fan Error 00h 02h Cover Error 00h 04h Temp Error 00h 08h D5V Error 00h 10h Power Error 00h 20h Temp Warning Error 00h 40h NVM Data Error 00h 80h Status Power 01[...]

21 VPL-VW100 <Table 3> Item Number Data Item Data Upper byte Lower byte ACK _ 00h 00h NAK Undefined Command 01h 01h Size Error 04h Select Error 05h Range Over 06h Not Applicable 0Ah Check Sum Error F0h 10h Framing Error 20h Parity Error 30h Over Rub Error 40h Other Comm Error 50h Waiting time for the return value is about 200 msec. n This wai[...]

22 VPL-VW100 List of SIRCS CODE <15BIT CATEGORY> <Table 4> LENS CONT TOGGLE RCP 7x WIDE MODE TOGGLE 6x DOT PHASE LENS ZOOM LENS SHIFT LENS FOCUS PICTURE MODE TGL PICTURE MODE USER3 ADJUST PICTURE TOGGLE PICTURE MODE USER2 PICTURE MODE USER1 PICTURE MODE CINEMA PICTURE MODE STANDARD PICTURE MODE DYNAMIC 5x DRC MODE TOGGLE 4x V KEYSTONE 3[...]

VPL-VW100 The material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permissi[...]

English Sony EMCS Corporation 2005LR16-1 Ichinomiya T ec ©2005 VPL-VW100 (SY) E 9-872-775-01[...]