Swisher ACR-500, ACR-500S manuale d’uso

ACREAGE RAKE 1602 CORPORA TE DRIVE PO BOX 67 WARRENSBURG, MISSOURI 64093 PH 660. 747. 8183 FAX 660. 747. 8650 swish erinc .com MANUFAC TURING QUA LITY LA WN CAR E EQU IPMENT SINCE 1945 Owner ’s Manua l IMPORTANT Read and foll ow all Safety Preca utions and Instr uctions Before Operating this Equipme nt. Made In CHINA ASSEMBLY OPERATION MAINTENANC[...]

LIMITE D WARRANTY The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in materials and wo rkmanship for a period of on e (1) y ea r from the date of pu rchase by the original consumer pu rchaser. We will repair or replace, at our discretion, parts found to be defective due to materials or workmansh[...]

SAFETY PRECAUTIONS Read this manual completely. Failur e to observe the foll owing safety instructions coul d result in serious inju ry or death. This Safety Alert Sy mbol indicates i mportant messages in thi s manual. When you see this sy mbol, carefully read th e message that follows and be alert to t he possibility o f personal in jury.  Read[...]

PRE-ASSEMBLY: Approximate assembl y time of this produ ct is ¾ of an hour. Helpful Tip : R ead a ll instructions b efore st arting to assembl e. TOOLS REQUIRED FOR ASSEMBLY (1) Pliers (2) 14mm Wrenches (2) 19mm Wrenches (1) 24mm Wrench REMOVE ALL PARTS FROM CARTONS 1. Remove the h ardware p acks and all p arts from t he cartons. 2. Layout and id e[...]

HARDWARE PACK CONTENTS: (Photo of Parts not Actual Si ze) OPTIONAL ACCESSOR IES: Check with R etail er where you purchased this p roduct for these opti onal attachm ents. Or you ma y call the mf g at (800) 222-8183 fo r acc essories and repla cemen t parts. Part/Item# Descrip tion HTC-500 Sweeper Hitch At tachme nt for towin g sweepers Replacem ent[...]

Figure 1 ASSEMBLY INSTRU CTIONS STEP 1: ATTACH TONGUE TO AXLE Place tongue ass embly (#4) and axle as sembly(#1) on a flat surface. Position the tongue so that the diameter of 19mm x length of 118mm shaft welded to the tongue is straight up. Orientate the axle(#1) so the lift arm hinges welded to the axle face away from the tongue. See figure 1 . C[...]

STEP 4: ATTACH CABLE PIVOT BAR Attach the two lift cable pivot bars (K) to the diam eter of 19mm x length of 118mm shaft on the tongue assembly. Install each pivot bar on top of shaft, use a diameter 8mm Teflon washer (D) between the two bars, then se cure with a M8 nylock nut (M) . The cables and lock pins should b e positioned facing the rear of [...]

STEP 8: ATTACHING RAKE ARMS Insert the rake wheel arm(#2) into the lift arm from in STE P 7. Secure rake wheel arm to the lift arm using lock pin attached to end of the lift cable. See figure 8 for rake arm position. Repeat procedure for the rake arm on opposite side. STEP 9: ATTACH RAKING WHEELS Attach three rake tine wheels(#6) to rake wheel axle[...]

ADJUST T HE OPERATI NG HEIGHT of LIFT ARM S NOTE: Adjustments may be n eeded b ased on the hei ght of the towing v ehicle hit ch. Step 10: Attach th e Acrea ge Rake to th e towing v ehicle hitch. Follow Steps 11,12, and 13 for each li ft arm. These steps are to mak e s ure rake reel tines will: (1) lift h igh enough for towin g clearance, and (2) r[...]

OPERATION AN D MAINTENA NCE SETTTING RAKE TI NE WHEELS FOR THATCHING VS. RAKING 1. 1.. Acreage rake has been assembled for raking. See figure 14 . Note the direction of the tine tips. To position rake tine wheel asse m bly for thatching, remove lock pin from both lift arms and remove both rake tine wheel assemblies from rake. Take the l eft rake ti[...]

MAINTENANCE AND RECOMMENDATI ONS FOR BEST RESULTS Operating Tip: Rake works for picking up Acorns or similar small particles other than grass/leaves RAKE TINE WHEEL MAIN TENANCE: Following these recommendations will make the raking wheels last longer. 1. It is recommended to mow or cut grass to 3” or less before raking or de-thatching. 2. Rake Wh[...]

swish erinc .com MANUFAC TURING Q UALITY LAWN CARE EQUIP MENT S INCE 1945 WHEN ORDERING PARTS, PLEASE HAVE THE FOLLOWING INORMATION A VAILABLE: * PRODUCT – ________________ * SERIAL NUMBER - _______________ * MODEL NUMBER - _______________ TYPE - ________ _______ * PART NUMBER W ITH PAINT CODE * PART DESCR IPTION TELEPHONE - 1-800-222-8 183 FAX -[...]