Tandberg Data 7000 manuale d’uso

1 Software version B4 D12014-07 This document is not to be reproduced in whole or in part without permission in writing from: User Manual[...]

2 T ANDBERG Videoconferencing System PLASMA MONITORS: Panel sticking and af ter-image lag A void displaying the same images continuously over a long period of time on the T ANDBERG 7000 monitors. Displaying the same images such as still images for a long time may cause after-image lagging. This may occur in the following two cases: 1. After image l[...]

T ANDBERG Videoconferencing System 3 Environmental Issues Thank you for buying a product which contributes to a reduction in pollution and thereby helps save the environment. Our products reduce the need for travel and transport and thereby reduce pollution. Our products have either none or few consumable parts (chemicals, toner, gas, paper). Our p[...]

4 T ANDBERG Videoconferencing System Operator Safety Summary For your protection, please read these safety instructions completely before operating the equipment and keep this manual for future reference. The information in this summary is intended for operators. Carefully observe all warnings, precautions and instructi ons both on the apparatus an[...]

T ANDBERG Videoconferencing System 5 Content s Introduction ........................................................................................ 7 Menu structure ................................................................................... 8 T ANDBERG 7000 V ideoconferencing System ................................ 9 At a glance — the T [...]

6 T ANDBERG Videoconferencing System Advanced use .................................................................................. 4 7 Main menu ..................................................................................................... 47 Call quality .....................................................................................[...]

T ANDBERG Videoconferencing System 7 Introduction This User Manual is provided to help you make the best use of your T ANDBERG system. The T ANDBERG system offers superior quality audio and video in a fully-featured unit. Main Features: • Supports videoconferencing via both IP and ISDN networks. • Selection of up to 3 Mbps call quality . • Bu[...]

8 T ANDBERG Videoconferencing System Menu structure The on-screen menu structure is shown below . Press the M ENU key on the remote control to enter/leave the Main Menu. Call Quality Advanced Settings Main Menu Press U P /D OWN /L EFT /R IGHT to navigate. Press O K to select. OK MCU Services Audio Settings Presentations Video Settings Utilities T e[...]

T ANDBERG Videoconferencing System 9 T ANDBERG 7000 V ideoconferencing System At a glance — the T ANDBERG 7000 system[...]

10 T ANDBERG Videoconferencing System W .A.V .E. Camera The Main Camera is mounted on top of the monitor . The Main Camera includes a high quality color camera with a fast pan/tilt/zoom action. The Main Camera is controlled by the system’s infra-red remote control and operates pan/tilt, focus and zoom. Y ou can pre-store up to ten camera position[...]

T ANDBERG Videoconferencing System 11 Remote control The remote control is used to control all functions of the system. If the screen saver is activated (black monitor), touching the remote control will automatically switch of f the screen saver .[...]

12 T ANDBERG Videoconferencing System T able microphone The high quality table microphone is specially designed to be used on a table during a video conference. The ideal location for the microphone is on a flat surface at least 2m (6.5 ft) from the front of the system. The microphone cable should always point towards the system. Y ou can connect u[...]

T ANDBERG Videoconferencing System 13 Installation Precautions • Never install telephone wiring during a lightning storm. • Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. • Never touch uninstalled telephone wires or terminals unless the telephone line has been disconnected at the net[...]

14 T ANDBERG Videoconferencing System Installation Unpacking the Base Due to the weight of the system, the base should be placed in its permanent location as soon as it is unpacked. Unpacking and Installing the Monitor Rack Lift the Monitor Rack out of the box. Do not remove the straps or packaging that are around the rack. Place the rack on top of[...]

T ANDBERG Videoconferencing System 15 Installation T HE CAMERA SHOULD BE ALIGNED WITH THE FRONT EDGE OF THE MONITOR TO ENSURE THE IR- SENSOR IN THE CAMERA CAN PICK UP SIGNALS FROM THE REMOTE CONTROL . Inst alling Installing the monitor(s) We recommend that there are 3 people present when installing the monitor(s). •Remove the plastic plugs locate[...]

16 T ANDBERG Videoconferencing System Installation Connecting cables All cables needed in standard configuration are connected to the codec. Connect these cables to the other parts of the system: 1. Power cable Connect the system power cable to an electrical distribution socket. 2. Monitor cables Connect the 2 BNC (Y/C input at the monitor), the 9 [...]

T ANDBERG Videoconferencing System 17 Installation Monitor configuration Power up the codec and the monitors. Use the monitor remote control to set the monitors to Y/C. Securing the cables It is important that the wires are secured inside the base so that they don’t get in the way of the covers, which are to be screwed on to the back. Attaching t[...]

18 T ANDBERG Videoconferencing System Installation System configuration • Switch the system on by activating the power switch on the codec (located on the right hand side at the rear of the codec). A green light is shown (located in the center on the front of the codec). • After the system has performed a self-test routine, product logo and a ?[...]

T ANDBERG Videoconferencing System 19 Installation ISDN configuration For each installation of the system it is necessary to configure the unit. All configuration parameters are available via the menu system. If you are using an external IMUX or special networks, the external equipment may also need to be configured. • Press M ENU on the remote c[...]

20 T ANDBERG Videoconferencing System Installation LAN configuration • Press M ENU on the remote control. Select the menu ‘ T erminal Settings ’, then ‘ LAN Settings ’ . S pecify the necessary LAN settings according to the instructions from your LAN administrator . If there is an H.323 Gatekeeper present on your LAN, see also ‘ H.323 Se[...]

T ANDBERG Videoconferencing System 21 Getting started Getting st arted System st art-up Y our system should be in standby mode. When in standby mode, pressing any key or picking up the remote control will wake up the system. An incoming call will also wake up the system. If the system does not respond, make sure the system is switched on by using t[...]

22 T ANDBERG Videoconferencing System Getting started Basics The system’s most commonly used functions are accessible directly from the remote control by single key presses. In addition, the user interface is represented by on-screen menus. Individual items within the menus and lists can be selected by moving a white highlighter bar to the desire[...]

T ANDBERG Videoconferencing System 23 Getting started Making and ending calls Making a call T o make a call, enter the number or the IP-address of the unit you wish to call using the Dialing keys and press C ONNECT . ISDN call The system will, by default, try to connect using Quality: Auto (see table overleaf). If the requested quality (bandwidth) [...]

24 T ANDBERG Videoconferencing System Getting started TIP Access Code If the system requires an Access Code, enter the code and press OK to proceed making a call: Using sub-address / extension address / MCU password T o specify an ISDN sub-address or its LAN equivalent extension address (TCS-4), add a star (*) af ter the number and then enter the s[...]

T ANDBERG Videoconferencing System 25 Getting started TIP Selecting / setting default quality (bandwidth) T YPE OF CALLS Auto 384kbps on ISDN/768kbps on LAN Max * 768kbps on ISDN-BRI * 1472/1920kbps (23/30Ch) on ISDN-PRI (T1/E1) * 3Mbps(3072kbps) on LAN 3072 3072 kbps (3Mbps, LAN only) 2560 2560 kbps (2,5Mbps, LAN only) 1920 1920 kbps (2Mbps, 30B) [...]

26 T ANDBERG Videoconferencing System Getting started Selecting / setting default network T o select a specific network, press ‘ Net ’ when you are in the dial menu.: • Highlight the network to be used in your call. • Press ‘ Select ’ to select network or press ‘ Set as Default ’ to set the selected network as your preferred choice [...]

T ANDBERG Videoconferencing System 27 Getting started Answer a call T o answer a call, press the C ONNECT key . Manual answer of a call is needed if the autoanswer facility is switched off. See ‘ Utilities ’ i n ‘ Advanced use ’ . End a call T o end a call, press the D ISCONNECT key . Correcting keying mistakes T o delete the last digit (or[...]

28 T ANDBERG Videoconferencing System Getting started T o find an entry , key in the first letter , for example T , and scroll with the up/down arrows. T HE LEFT / RIGHT ARROWS WILL MOVE ONE P AGE UP / DOWN . T o dial the selected entry press C ONNECT . T o edit the selected number before dialing, press OK (only point-to-point entries) . Directory [...]

T ANDBERG Videoconferencing System 29 General use Add New Entry When selecting ‘ Add New Entry ’, an empty directory entry is displayed: 1 Move to ‘ Name ’ and enter characters using the number keys on your remote control (as on mobile phones). Use ‘0’ to enter ‘space’, use ‘#’ to switch between upper- and lower case. 2 Move to [...]

30 T ANDBERG Videoconferencing System General use Add MultiSite Entry When selecting ‘ MultiSite Entry ’, an empty MultiSite directory entry is displayed: 1 Move to ‘ Name ’ and enter the MultiSite meeting name. 2 Select ‘ Add Site ’ to add a site to the meeting by searching for point-to-point entries in the directory list. See below fo[...]

T ANDBERG Videoconferencing System 31 General use mov e pip General use Adjusting volume Press the V OLUME keys to adjust the volume level. An on-screen indicator will show the current level. View outgoing video (selfview) Press the S ELFVIEW key to view your outgoing video. T o change the image being viewed on the monitor during a call press S ELF[...]

32 T ANDBERG Videoconferencing System General use Do Not Disturb / Sleep Mode Press any Quick key when not in a call to activate the Quick Menu. When Do Not Disturb is activated, the system will not accept any incoming calls. The caller will hear a busy tone when calling this unit. A status line will indicate when Do Not Disturb is active. When Sle[...]

T ANDBERG Videoconferencing System 33 General use Selecting video sources Press: to select the video source to be transmitted to the far end. doc cam main cam vcr pc aux OK zoom Controlling the Main Camera Moving / zooming camera T o control the Main Camera use the keys below: for pan/tilt and for zooming. I F THE MENU SYSTEM IS ACTIVE , THE ARROW [...]

34 T ANDBERG Videoconferencing System General use V oice Activated Camera Positioning Through V oice Activated Camera Positioning and the use of two or three microphones, the camera will automatically view the speaker . Setup Before using camera tracking, the camera positions used must be stored at presets P7 (Mic1), P8 (Mic2) and/or P9 (Mic3). E X[...]

T ANDBERG Videoconferencing System 35 General use Preset s The preset buttons enable you to pre-store up to ten different settings. Each preset is able to store: • Video source • Camera position, pan/tilt/zoom/focus/brightness (if Main Camera) • Audio source selection (see ‘Audio Settings’ in ‘Advanced use’) Selecting presets T o sele[...]

36 T ANDBERG Videoconferencing System General use OK Far end camera control (FECC) Press the F AR E ND key until the ‘ FarEndCamera ’ on-screen indicator is displayed. For this feature to operate the far end must support ‘Far end camera control’ (H.281). Whilst activated you will be able to control the far end’s camera (pan/tilt/zoom/focu[...]

T ANDBERG Videoconferencing System 37 General use Sending/receiving still images When a still image is sent, received or requested, it will be stored in the graphics memory . When a new image is sent or received, the old image will be erased. When disconnecting the call, the image will be erased. Sending a still image • Press S NAPSHOT . • T o [...]

38 T ANDBERG Videoconferencing System General use Duo Video Duo Video is useful if you want to display live video from your document camera or another camera in addition to live video of yourself. Add Duo Video • Alt.1: Press any other video source than MainCam during a call. This will open Duo Video directly if the far end supports the automatic[...]

T ANDBERG Videoconferencing System 39 General use End a Duo Video call T o end a Duo Video call, press D ISCONNECT . Select if you want to disconnect only the Duo Video connection or the whole connection. disconnect Controlling camera, changing video source, presets in a Duo Video call The main monitor will always display incoming video. The 2nd mo[...]

40 T ANDBERG Videoconferencing System General use MultiSite (MCU) The system has a built-in multipoint conference unit (MCU), MultiSite, which has the capability to establish meetings with up to 4 video sites (5 if at least one site is a telephone call, ISDN/analogue/mobile). The video calls in a conference must be connected using the same bandwidt[...]

T ANDBERG Videoconferencing System 41 General use MultiSite cascading By connecting four MultiSite systems together , it is possible to connect up to 10 video sites (including the four MultiSite sites) plus 4 audio sites (telephones), see drawing below . The host can connect up to 3 other video systems with MultiSite functionality . The host can us[...]

42 T ANDBERG Videoconferencing System General use • Press ‘ Add Site ’ to bring up the MultiSite dial menu. • Enter the number to call. The Quality will, by default, be the same as used by the first call. T o place a telephone call instead of a video call, press ‘ Quality ’ and select ‘ T eleph ’ in the Quality menu. T o use another[...]

T ANDBERG Videoconferencing System 43 General use Disconnecting sites from a conference T o disconnect a site or end the conference, press D ISCONNECT . • Select site and press O K or ‘ Disconnect Site ’. T o end the meeting press ‘ Disconnect All ’. disconnect E ACH SYSTEM WILL BE IDENTIFIED BY A S YSTEM N AME ( IF SUPPORTED ) AND THE NU[...]

44 T ANDBERG Videoconferencing System General use PC Presenter Plugging a PC into the system is made extremely simple through the PC Presenter , avoiding the need for any additional hardware such as a projector , PC/V ideo converter or extra cables. • Connect the pre-connected VGA cable to your PC (VGA Output). • S tart your PC. • Press P C o[...]

T ANDBERG Videoconferencing System 45 General use Web-interface It is possible to access and maintain the system remotely via a local area network (LAN) using a standard Web- browser . Connect your system to a local area network. Configure your codec: • Press MENU, select ‘ T erminal Settings ’, ‘ LAN Settings ’ • S pecify IP-assignment[...]

46 T ANDBERG Videoconferencing System General use Streaming T o view streaming, select ‘S treaming’ from the Web-page of the codec. See sep arate ‘S treaming’ section in this manual for further information.[...]

T ANDBERG Videoconferencing System 47 Advanced use Main menu The menu system can be used to select available functions and utilities for the system. T o enter the menu system and the main menu, press the M ENU key . Y ou may leave the menu system at any time by pressing the M ENU key . T o navigate through the menu system, use the cursor keys to mo[...]

48 T ANDBERG Videoconferencing System Advanced use Call quality The Call Quality menu allows you to select the preferred quality of your call. D UE TO ACTIONS OR LIMIT A TIONS AT THE FA R END YOU MA Y NOT AL WA YS BE ABLE TO ACHIEVE THE SELECTIONS YOU WANT . Audio Auto Optimized audio quality depending on bandwidth. High High audio quality (G722) r[...]

T ANDBERG Videoconferencing System 49 Advanced use Advanced call quality NOTE T HE SELECTIONS MADE IN THIS MENU WILL OVERRIDE THE SELECTIONS MADE IN THE ‘C ALL Q UALITY ’ MENU . I F ‘A UTO ’ IS SELECTED , THE SETTINGS IN ‘C ALL Q UALITY ’ WILL BE USED . Audio Auto The setting of ‘ Audio: Auto/High/Normal ’ in ‘ Call Quality ’ wi[...]

50 T ANDBERG Videoconferencing System Advanced use Present ations Presentation Mode T o send a still image immediately after pressing S NAPSHOT select ‘ Present ation Mode: Normal ’. T o preview the image before it is transferred as a still image, select ‘ Presentation Mode: Preview ’. When pressing S NAPSHOT you will be allowed to view you[...]

T ANDBERG Videoconferencing System 51 Advanced use Duo Video Number* Auto When adding Duo Video in a conference, Duo Video is connected automatically if supported by the far end. Manual When adding Duo Video in a conference and connected towards a system with no Duo Video capabilities, enter the Duo Video Number into the ‘Number’ field in the ?[...]

52 T ANDBERG Videoconferencing System Advanced use Utilities Autoanswer On : The system will automatically answer all incoming calls. On+MicOff : The system will automatically answer all incoming calls and switch the microphone off when the call is connected. Press M IC O FF to switch the microphone on. Off : Y ou must manually answer all incoming [...]

T ANDBERG Videoconferencing System 53 Advanced use Auto-PIP On : Y our selfview will automatically be displayed (as a Picture-in-picture) whenever the camera position or video source is changed. Picking up the remote control will also display your selfview . Welcome Menu The Welcome menu can be shown when the system is not in use, and when sleep-mo[...]

54 T ANDBERG Videoconferencing System Advanced use MCU services A Multipoint Control Unit (MCU) enables several sites to participate in the same conference. An MCU conference can have different modes: V oice Switched means that the image of the person currently speaking will be broadcast to all the other conference participants. This will remain th[...]

T ANDBERG Videoconferencing System 55 Advanced use Quick Menu When connected to an MCU P RESS ANY Q UICK KEY WHEN IN A MUL TIPOINT CONFERENCE TO ACTIV A TE THE Q UICK M ENU . This menu provides access to the most commonly used MCU functions. If ‘ Request Floor ’ is selected, ‘Request Floor’ will change to ‘Release Floor’. If ‘ View Si[...]

56 T ANDBERG Videoconferencing System Advanced use Request floor When requesting the floor , the MCU will broadcast your video in full screen to all other participants in the conference. If the MCU conference has a chairman, a floor request is sent to the chairman. Y ou will remain ‘On Air ’ until either you select ‘ Release Floor ’ or the [...]

T ANDBERG Videoconferencing System 57 Advanced use Chair control * Y ou select ‘ Chair Control ’ and ‘ T ake Chair ’ to assume the role of chairman of the ‘meeting’. As chairman, you may control which site you and the other sites see. T ake chair Allows you to request chairmanship of the conference. If no one else is currently chairman [...]

58 T ANDBERG Videoconferencing System Advanced use Audio Settings Audio Inputs By default, all inputs are enabled. Just plug in an audio source and it is active. Audio inputs that are On will automatically be mixed. Select Off to prevent audio/noise from unused inputs or if you want to disable a specific input. The activated audio sources are store[...]

T ANDBERG Videoconferencing System 59 Advanced use As there is no acoustic echo canceller on this input it should not be connected to any microphones. The audio entering this input will be heard from the local speaker . Audio input 6 is intended for connection to a VCR. It can also be connected to other external playback devices. As there is no aco[...]

60 T ANDBERG Videoconferencing System Advanced use Audio Outputs Audio out 1 is intended for connection to T ANDBERG Natural Audio, televisions or audio amplifiers. Audio out 2 is intended for connection to audio recording equipment or to a telephone add-on hybrid. The signal is a mix of audio from both the far end and local end (not from Audio in [...]

T ANDBERG Videoconferencing System 61 Advanced use Echo Control Each of the 3 microphone inputs and Audio input 4 have a separate echo canceller . One echo canceller per input provides more sophisticated control than having one common canceller for all microphones. Echo control is normally set to ‘ On ’ to prevent the far end from hearing their[...]

62 T ANDBERG Videoconferencing System Advanced use Room Size This setting allows optimization of the echo canceller to the acoustic size of the room. Hard walls, many windows etc. might require higher settings than expected. Carpets, curt ains etc. might require lower settings. Adjust the setting (NOTE: on the far end) if one of the following sympt[...]

T ANDBERG Videoconferencing System 63 Advanced use Automatic Gain Control (AGC) Settings Select ‘ On ’ to allow automatic adjustments (Automatic Gain Control) of audio levels. When ‘ On ’, the AGC maintains the audio signal level at a fixed value by attenuating strong signals and amplifying weak signals. V ery weak signals, i.e. noise alone[...]

64 T ANDBERG Videoconferencing System Advanced use Alert T ones & V olume T o help distinguish between incoming video calls and ordinary telephone calls, different ringing tones may be selected. Y ou may also select different volume levels for the ringing tone. Alert Speaker The system also has an internal, call alerting speaker . On : The inte[...]

T ANDBERG Videoconferencing System 65 Advanced use Video Settings Camera T racking Mode Select the camera tracking mode: Slow: The system waits a while before zooming in on a single person speaking. Suitable when wide-angle images are preferred over close-up images. Norm: Should be used in regular meetings. Fast: The system quickly zooms in on a si[...]

66 T ANDBERG Videoconferencing System Advanced use Video Name Each video input defaults to the same name used on the remote control to select a video input. T o edit the name, use the number keys on the remote control to select letters. Press D ELETE to erase a letter . Focus T o manually adjust the focus select ‘ Manual ’ and use the arrow key[...]

T ANDBERG Videoconferencing System 67 Advanced use VGA Settings VGA Out T o enhance the local video quality , a VGA monitor may be connected. Main : Should be used if you want to use a VGA monitor as your main monitor . Video outputs 1&3 will be disabled. Dual : Should be used if you want to use a VGA monitor as your dual monitor . Video output[...]

68 T ANDBERG Videoconferencing System Advanced use Address The IP-address of the PC with the VNC software inst alled. T o find the IP-address of the PC, select ‘Command Prompt’ from the St artup-menu. T ype ‘ipconfig’ and press ENTER. Display Number The display number for VNC is 0 and upwards. If you are using WinVNC, double-click on the ic[...]

T ANDBERG Videoconferencing System 69 Advanced use T erminal Settings This menu provides basic network setup for the unit and should be used when installing the system. Network Configuration Before using the system it is necessary to specify which network to use and define its settings. If you want to use your system via ISDN-BRI you should select [...]

70 T ANDBERG Videoconferencing System Advanced use If you want to use your system via ISDN-PRI, you should select ‘ Current Network: ISDN-PRI ’ and enter the ‘ ISDN-PRI Settings ’ menu to set the PRI parameters. If you want to use your system via Leased E1/T1, you should select ‘ Current Network: Leased E1/T1 ’ and enter the ‘ Leased [...]

T ANDBERG Videoconferencing System 71 Advanced use ISDN-BRI Settings M ANDA TO R Y ISDN-BRI SETTINGS T O MAKE SURE YOUR SYSTEM WILL WORK PROPERL Y USING ISDN-BRI, MAKE THE FOLLOWING SETTINGS : - S ET ISDN SWITCH TYPE - E NTER ISDN LINE NUMBERS (+ SPID S IF REQUIRED ) - D ISABLE UNUSED LINES ISDN switch type Select the type of ISDN network connected[...]

72 T ANDBERG Videoconferencing System Advanced use Line setup This menu allows you to program the numbers associated with your ISDN line. If you want to use this ISDN line, you need to set ‘ Enabled: On ’ and enter the numbers of your ISDN line. If some of the ISDN lines are not to be used, set ‘ Enabled: Off ’. Line 1 should always be enab[...]

T ANDBERG Videoconferencing System 73 Advanced use Advanced ISDN settings Subaddress Using a subaddress enables you to connect up to eight ISDN terminals to the same ISDN telephone number and line. The terminals are addressed by using different subaddresses. T o call a terminal with a subaddress, separate the ISDN telephone number and the subaddres[...]

74 T ANDBERG Videoconferencing System Advanced use MSN (Multiple Subscriber Number) The use of MSN (Multiple Subscriber Number) enables you to attach different ISDN terminals, with different numbers, to the same physical ISDN telephone line. If ‘ V alidate Numbers ’ is set to ‘ On ’ only calls to those numbers specified in the Line Setup me[...]

T ANDBERG Videoconferencing System 75 Advanced use PRI Switch T ype Select the type of PRI switch to which your unit is connected. ISDN-PRI Settings Number Enter the main number for your PRI line. If this number is programmed and ‘ MSN: On ’ (see ‘ V alidate numbers ’ in ‘ Advanced ISDN Settings ’) only calls to this number will be answ[...]

76 T ANDBERG Videoconferencing System Advanced use Channel Hunting Below is a list of common ISDN-PRI/T1 switches. T y pe Manufacturer PRI Switch T ype setting A TT 4 ESS A T & T A T&T ISDN A TT 5 ESS A T&T/Lucent A T&T ISDN or National ISDN * DMS 100 Northern T elecom National ISDN DMS 250 Northern T elecom National ISDN * Settings[...]

T ANDBERG Videoconferencing System 77 Advanced use Advanced ISDN Settings This is the same menu as for ISDN-BRI. The settings will be common for ISDN BRI and ISDN PRI. Please refer to section ‘ISDN-BRI Settings’. Line Settings ‘T1 Cable Length 1’ specifies the distance to the CSU connected to the ‘E1/T1 1’ port on codec 1. Cable Length [...]

78 T ANDBERG Videoconferencing System Advanced use Advanced ISDN-PRI Settings NSF - Non S tandard Facility . Y our network provider may require a service selection in your ISDN configuration. Enter the Service code here. V alid NSF service codes are from 1 to 31. Enter 0 to disable NSF service codes. Example: A T&T of fers several digital switc[...]

T ANDBERG Videoconferencing System 79 Advanced use Leased E1/T1 Settings Network Interface Indicates if the network is of type E1 (30 channels) or T1 (24 channels). E1 will be default for P AL versions, T1 default for NTSC versions. Max Channels Indicates the maximum number of channels the codec is allowed to use on the E1/T1 interface. When E1 is [...]

80 T ANDBERG Videoconferencing System Advanced use External network settings Before using the system together with external network equipment, you must specify the network parameters on this page. T HE SYSTEM HAS SUPPORT FOR UP TO 768 KBPS /2M BPS USING THE E XTERNAL N ETWORK (RS449/V .35/X.21) INTERF ACE . Call control ‘ RS366 Dialing ’ is the[...]

T ANDBERG Videoconferencing System 81 Advanced use Network clocking The network clock setting specifies the number of physical external clock signals. Use ‘ RS449/V35 Compatible ’ when the external equipment provides two clock signals, one for transmit and one for receive. The difference between RS449 and V35 is the cable only . Use ‘ X21 Com[...]

82 T ANDBERG Videoconferencing System Advanced use Address Address is defined as the IP-address of a streaming client, streaming server or a multicast address. Giving an address in the range 224.0.0.1-239.255.255.255 will broadcast the stream to any host that has joined the specified multicast group. S pecifying normal broadcast address 255.255.255[...]

T ANDBERG Videoconferencing System 83 Advanced use Streaming Source Auto Enables streaming of both local and far end video. Selection of which site to be streamed is done using voice switching (the site that speaks is streamed). Local Only the local video will be streamed. Remote Only the far end video will be streamed. Local and far end audio is a[...]

84 T ANDBERG Videoconferencing System Advanced use H.323 Settings E.164 alias This is the E.164 address of the codec. The E.164 address is equivalent to a telephone number , sometimes combined with access codes. V alid characters are 0-9,* and #. When using a gatekeeper the codec will send a message to the gatekeeper containing both the E.164 addre[...]

T ANDBERG Videoconferencing System 85 Advanced use Advanced H.323 Settings IP Precedence Used to define which priority the system should have in the network. Higher numbers indicate higher priority . The selected value n will classify the different p ackets as follows: Signalling=n, Audio=n-1, Video=n-2, Dat a=n-3. When ‘Auto’ is selected, n ha[...]

86 T ANDBERG Videoconferencing System Advanced use NA T NA T , Network Address T ranslation, is used in small LAN’s, of ten home offices, when a PC and a videoconferencing system is connected to a router with NA T support. NA T support in the videoconferencing system enables proper exchange of audio/video data when connected to an external videoc[...]

T ANDBERG Videoconferencing System 87 Advanced use IP Settings IP-assignment DHCP (Dynamic Host Configuration Protocol) can be selected when a DHCP server is present. DHCP: IP-address, IP-subnet mask and Gateway are not used because these parameters are assigned by the DHCP server . Static: The codec’s IP-address and IP-subnet mask must be specif[...]

88 T ANDBERG Videoconferencing System Advanced use Ethernet Speed Auto The codec will auto-detect the speed/duplex on the LAN. 10/Half The codec will connect to the LAN using 10Mbps speed/Half Duplex. 10/Full 10 Mbps speed/Full Duplex. 100/Half 100 Mbps speed/Half Duplex. 100/Full 100 Mbps speed/Full Duplex. Restart Pressing the Quick key ‘Restar[...]

T ANDBERG Videoconferencing System 89 Advanced use Call Settings Incoming MCU calls On : When you are in a call, the system will provide a visual/audio indication of an incoming call and ask you to accept/reject the call. Off : The system will not accept incoming calls when you are in a call. Incoming telephone calls On : The system will accept inc[...]

90 T ANDBERG Videoconferencing System Advanced use Network Profiles This menu defines the settings listed when pressing the Quick key ‘ Net: ’ while in the dial menu. Encryption Auto The system will try to make ISDN point-to-point calls using encryption. If the far end system supports encryption, the call will be encrypted. If not, the call wil[...]

T ANDBERG Videoconferencing System 91 Advanced use Dat aport configuration The system provides two standard RS 232 serial ports to allow a computer to be connected for data transfer and control purposes. W HEN CONNECTING TO A PC THE CONNECTING CABLE MUST BE A STRAIGHT THROUGH RS232 CABLE . Dataport 1 If you wish to connect a PC to Dataport 1, you m[...]

92 T ANDBERG Videoconferencing System Advanced use Modem mode Allows you to control the system externally via a PC as in Control Mode. Once a call is established, Dataport 1 will automatically switch to Data mode. When the call disconnects, Dataport 1 switches back to Control Mode. T .120 Provides a dat a channel supporting the T .120 standard for [...]

T ANDBERG Videoconferencing System 93 Advanced use Sof tware Options The system requires a valid option key to activate MultiSite and/or Presenter functionality . A restart of the system is required after entering a new option key . If the option key is invalid, the original key will be used. Language The system supports 9 different languages for i[...]

94 T ANDBERG Videoconferencing System Advanced use Channel status Comprehensive information about the call progress is available through the Channel S tatus window . This window indicates the various stages each B-channel goes through whilst establishing a connection. Status - BRI Comments Idle the channel is idle Calling when calling — the netwo[...]

T ANDBERG Videoconferencing System 95 Advanced use P RESS M ENU AND THEN ’ C ALL S TA TUS ’ TO BRING THIS MENU UP WHEN NOT IN THE MENU SYSTEM . The numbers used to call out to the far end are shown in the window . If an error occurs a cause code will be displayed on the right hand side of the window . Cause codes The most common cause codes (fo[...]

96 T ANDBERG Videoconferencing System Advanced use Please contact your T ANDBERG representative for further information. Restore defaults Y ou may restore all system settings to the factory default using this function. T HIS DEF AULT SETTING WILL NOT AFFECT YOUR C ALL D IRECTORY INFORMA TION , N ETWORK T YPE , L INE S ETUP NUMBERS OR YOUR SPID NUMB[...]

T ANDBERG Videoconferencing System 97 Advanced use T est subsystem Y ou can test the different subsystems of your videoconferencing equipment. Far End Loop (ISDN only) SetLocal: This system will loop all incoming audio and video. · The far end will see its own video and hear its own audio. · The local side will see and hear the far end. An on-scr[...]

98 T ANDBERG Videoconferencing System Peripherals Peripheral Equipment Using the optional peripheral devices outlined in this chapter and the many others available, you will be able to build your own applications for use with the system, thereby better integrating the system into your business environment. This chapter will explain how to connect p[...]

T ANDBERG Videoconferencing System 99 Peripherals 5 Video Inputs • 2 video inputs supporting S-Video through Mini-DIN connectors. • 2 video inputs supporting composite signals through RCA connectors. • 1 VGA input supporting resolutions from 640x480 to 1024x768 (auto sensing). The standard camera uses one of the S-V ideo inputs. The system wi[...]

100 T ANDBERG Videoconferencing System Peripherals Dual Monitor The Dual Monitor can be used to show full screen selfview , still images and Duo Video. T o use the system in the Dual Monitor configuration: • Connect ‘V ideo Out 2’ (preferably) otherwise 4 on the system to a video input on the dual monitor . • Set ‘ Dual Monitor: On ’ in[...]

T ANDBERG Videoconferencing System 101 Peripherals Document camera A document camera can be used for showing text, diagrams and a variety of graphical material as well as small three-dimensional objects. T o use a document camera with your system: • Connect the document camera to the DocCam input on the Codec. • Press D OC C AM on the remote co[...]

102 T ANDBERG Videoconferencing System Peripherals Multiple controllable cameras Attaching multiple cameras to one system expands visibility and is useful in large group applications. The system is able to control up to 4 W A VE-cameras. Optional WA VE-cameras are supplied with a cable and a power supply . W A VE-camera number two must be connected[...]

T ANDBERG Videoconferencing System 103 Peripherals AudioScience microphone T ANDBERG's award-winning AudioScience microphone is a ceiling-mounted, wide coverage, boundary microphone, that can eliminate the need for table microphones. It is designed to pick up the audio from all conference participants seated within in its pick-up area, defined[...]

104 T ANDBERG Videoconferencing System Peripherals Video Cassette Recorder (VCR) VCR - Playback For playback, connect a cable between Video Out on the VCR and ‘VideoIn 4 (VCR)’ on the system. Connect a cable between Audio Out on the VCR and the VCR audio input on the system. T O SIMPLIFY CONNECTING A VCR, THE NECESSARY CONNECTORS ARE MARKED ‘[...]

T ANDBERG Videoconferencing System 105 Peripherals T elephone Add-On A telephone add-on is used when you want to include a telephony participant in the meeting. Y ou can also use this functionality when you want to have conference participants in an adjacent room with its own microphone and speaker system. The telephone add-on connectors are marked[...]

106 T ANDBERG Videoconferencing System Peripherals T .120 / data Dataport 1 COM port PC applications A PC can be connected to the system in two different ways. • Through the PC Presenter (VGA input), see section ‘PC Presenter’. • Through an RS232 data cable. T .120 and other PC applications A PC can be connected to the system using a serial[...]

T ANDBERG Videoconferencing System 107 Peripherals Additional microphones If your environment is such that you require more than one microphone for your room, e.g. you have a whiteboard at a distance from your table microphone, it is possible to connect additional microphones to your system. Y ou can connect up to three additional microphones to yo[...]

108 T ANDBERG Videoconferencing System Appendices Appendices Appendix 1: Connecting the system to ISDN using NT1 network adapters Connecting Connect the first ISDN cable from ISDN 1 on the codec to the S-interface on your first NT1 network adapter . Connect the other ISDN cables to the appropriate NT1 network adapters. Connect the U-interface of yo[...]

T ANDBERG Videoconferencing System 109 Appendices Appendix 2: Connecting the system to the Switched 56 network Using T elesync TS-256 SW56/ISDN adapter Connecting the system to the SW56 network using a T elesync Adapter is described below . NOTE: There are dif ferent T elesync Adapters for different configurations of SW56 networks. The network type[...]

110 T ANDBERG Videoconferencing System Appendices Appendix 3: Connecting the system to PRI/T1 Using CSU adapter Connecting the system to the ISDN network via the E1/T1-interface using an Adtran T1 ESF CSU ACE will allow up to 1.54 Mbps transmission. The E1/T1-interface must be connected to a CSU approved according to IEC 60950, UL 1950 or equivalen[...]

T ANDBERG Videoconferencing System 111 Appendices Appendix 4: Environment al considerations This section explains how to carry out basic adjustments and simple tests to ensure that you send and receive the best possible image and audio quality when using your system. Iris control and lighting By default the system camera will use an automatic iris [...]

112 T ANDBERG Videoconferencing System Appendices How to prepare a typical room for videoconferencing The diagram below shows a typical room designed to obtain the best results when using the system. The microphone should be placed at the front of the table to ensure that all speech will be detected. The best position for the microphone is at least[...]

T ANDBERG Videoconferencing System 113 Appendices Appendix 5: Using the file system It is possible to access a file system within the T ANDBERG system by using ftp: DOS-window: ftp <IP-address of codec>, or Web-browser: ftp:// <IP-address of codec> Description of the different files all.prm - all settings in the system (including direct[...]

114 T ANDBERG Videoconferencing System Appendices Appendix 6: Access Code The system will verify if the entered access code is valid by checking the code with the allowed codes listed in the ‘access.txt’ file on the ftp-server in the codec. If no ‘access.txt’ file is uploaded to the codec, registration of the code will be done without valid[...]

T ANDBERG Videoconferencing System 115 Appendices Appendix 7: Declaration of Conformity[...]

116 T ANDBERG Videoconferencing System Index Index A Access Code 24, 89, 114 Add Duo V ideo 38 Add MultiSite Entry 30 Add New Entry 29 Adding an extra site 42, 43 Additional microphone 107 Adjusting volume 31 Advanced call quality 49 Advanced ISDN settings 73 Advanced use 47 Alert Speaker 64 Audio inputs 58, 99 outputs 60, 99 quality 48 setup 58 so[...]

T ANDBERG Videoconferencing System 117 Index Introduction 7 IP-address 87 IP-subnet mask 87 Iris control and lighting 111 ISDN switch type 71 ISDN-BRI Settings 71 ISDN-PRI/T1 Settings 75 L Leased E1/T1 79 Level Settings Outputs 60 Line setup 72 Logo 113 Loudspeaker volume 111 M Main camera 10 MCU services 54 Menu structure 8 Menu system 47 Micropho[...]

118 T ANDBERG Videoconferencing System Index T o use the dataport for PC applications 107 Tracker 103 Trademarks 3 U Unpacking 13 Using a SUB-address 73 Utilities 52 V VCR - Playback 104 VCR - Recording 104 VGA Resolutions 48 VGA Settings 67 V ideo 48 input 65 inputs 33, 99 mode 49 outputs 99 sources 33 V ideo call 23 V ideo cassette recorder (VCR)[...]