Tiger T6000 manuale d’uso

P AR TS LISTING WITH MOUNTING AND OPERA TING INSTRUCTIONS SABER MOWER NEW HOLLAND T6000 Tiger Corporation 3301 N. Louise Ave. Sioux Falls, SD 57107 1-800-843-6849 1-605-336-7900 www .tiger-mowers.com Current as of 06/17/201 1 06022005[...]

T O THE OWNER / OPERA T OR / DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize [...]

FOR W ARD This manual contains information about many features of the T iger mowing and roadside maintenance equipment. Some of these include: Safety precautions, Assembly instructions, Operations, Maintenance and Parts. This manual will also assist you in the proper break-in, daily care, and troubleshooting of your new mower . We recommend that yo[...]

[...]

T ABLE OF CONTENTS SAFETY SECTION _____________________________________ 1 ASSEMBL Y / MOUNTING SECTION ______________________ 2 OPERA TION SECTION _________________________________ 3 MAINTENANCE SECTION ______________________________ 4 P ARTS SECTION ______________________________________ 5 COMMON P ARTS SECTION ____________________________ 6 W ARR[...]

[...]

Saber Safety Section 1-1 SAFETY SAFETY SECTION[...]

Saber Safety Section 1-2 SAFETY Indicates an imminently hazardous situation that, if not avoided, WILL result in DEA TH OR VERY SERIOUS INJURY . Indicates an imminently hazardous situation that, if not avoided, COULD result in DEA TH OR SERIOUS INJUR Y . Indicates an imminently hazardous situation that, if not avoided, MA Y result in MINOR INJURY .[...]

Saber Safety Section 1-3 SAFETY DANGER! Never operate the Tractor or Implement until you have read and completely understand this Manual, the Tractor Operator’s Manual, and each of the Safety Messages found in the Manual or on the Tractor and Implement. Learn how to stop the tractor engine suddenly in an emergency . Never allow inexperienced or u[...]

Saber Safety Section 1-4 SAFETY DANGER! Never allow children or other persons to ride on the Tractor or Implement. Falling off can result in serious injury or death. (SG-10) DANGER! Never allow children to operate or ride on the Tractor or Implement. (SG-11) WARNING! Do not mount the tractor while the tractor is moving. Mount the tractor only when [...]

Saber Safety Section 1-5 SAFETY WARNING! T ransport only at safe speeds. Serious accidents and injuries can result from operating this equipment at unsafe speeds. Understand the T ractor and Implement and how it handles before transporting on streets and highways. Make sure the T ractor steering and brakes are in good condition and operate properly[...]

Saber Safety Section 1-6 SAFETY WARNING! Never attempt to lubricate, adjust, or remove material from the Implement while it is in motion or while tractor engine is running. Make sure the tractor engine is OFF before working on the Implement. (SG-20) WARNING! Periodically inspect all moving parts for wear and replace when necessary with authorized s[...]

Saber Safety Section 1-7 SAFETY DANGER! NEVER use drugs or alcohol immediately before or while operating the Tractor and Implement. Drugs and alcohol will affect an operator’s alertness and coordination and therefore affect the operator’s ability t o operate the equipment safely. Before operating the Tractor or Imple- ment, an operator on presc[...]

Saber Safety Section 1-8 SAFETY WARNING! Extreme care should be taken when operating near loose objects such as gravel, rocks, wire, and other debris. Inspect the area before mowing. Foreign objects should be removed from the site to prevent machine damage and/or bodily injury or even death. Any objects that cannot be removed must be clearly marked[...]

Saber Safety Section 1-9 SAFETY WARNING! Do not mow with two machines in the same area except with Cab tractors with the windows closed. (SGM-11) DANGER! Rotary and Flail Mowers are capable under adverse conditions of throwing objects for great distances (100 yards or more) and causing serious injury or death. Follow safety messages carefully. STOP[...]

Saber Safety Section 1-10 SAFETY Relieve hydraulic pressure prior to doing any maintenance or repair work on the Implement. Place the Mower Head on the ground or securely supported on blocks or stands, disengage the PTO, and turn off the engine. Push and pull the control Levers or Joystick several times to relieve pressure prior to starting any mai[...]

Saber Safety Section 1-11 SAFETY WARNING! In addition to the design and configuration of this Implement, including Safety Signs and Safety Equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of personnel involved in the operation, transport, maintenance, and storage of the machi[...]

Saber Safety Section 1-12 SAFETY 002369 HYDRAULIC T ANK 00725746 INSIDE OF CAB 00769737 MOWER DECK P AR T NO. LOCA TION[...]

Saber Safety Section 1-13 SAFETY 02962764 MAIN BOOM, SECONDARY BOOM, MAIN FRAME 02962765 MAIN FRAME 02965262 HYDRAULIC T ANK P AR T NO. LOCA TION 00758194 MOWER DECK[...]

Saber Safety Section 1-14 SAFETY 02967668 MOWER DECK 03200285 OUTSIDE OF CAB 02971 123 HYDRAULIC T ANK 22645 INSIDE OF CAB 22839 MOWER DECK P AR T NO. LOCA TION[...]

Saber Safety Section 1-15 SAFETY 25387 INSIDE OF CAB 10” x 5.5” 31522 MOWER DECK, MAIN BOOM 18.25” x 10” 31523 HYDRAULIC T ANK 22840 INSIDE OF CAB 24028 MOWER DECK P ART NO. LOCA TION[...]

Saber Safety Section 1-16 SAFETY P AR T NO. LOCA TION 32449 HYDRAULIC T ANK 32428 MAIN BOOM[...]

Saber Safety Section 1-17 SAFETY 32709 INSIDE OF CAB 32708 HYDRAULIC T ANK 32707 HYDRAULIC T ANK P AR T NO. LOCA TION[...]

Saber Safety Section 1-18 SAFETY 33302 INSIDE OF CAB 33438 MAIN BOOM 33224 MOWER DECK P AR T NO. LOCA TION 35284 INSIDE OF CAB[...]

Saber Safety Section 1-19 SAFETY 33743 INSIDE OF CAB P AR T NO. LOCA TION 42350 MOWER DECK 33512 INSIDE OF CAB[...]

Saber Safety Section 1-20 SAFETY RED 42399 REFLECTIVE T APE MOWER DECK AMBER 42400 REFLECTIVE T APE MOWER DECK 6T3219 INSIDE OF CAB 6T3220 FRONT PUMP MOUNT 6T3217 MOWER DECK P AR T NO. LOCA TION[...]

Saber Safety Section 1-21 SAFETY 6T3222 INSIDE OF CAB 6T3225 INSIDE OF CAB 6T3224 MOWER DECK P AR T NO. LOCA TION 6T3230 INSIDE OF CAB[...]

Saber Safety Section 1-22 SAFETY 6T3249A MOWER DECK 6T3234 INSIDE OF CAB 6T3236 MOWER DECK 6T3233 HYDRAULIC T ANK P AR T NO. LOCA TION 6T3243 INSIDE OF CAB[...]

Saber Safety Section 1-23 SAFETY TB101 1 MOWER DECK 6T3261 MOWER DECK P AR T NO. LOCA TION 34852 HYDRAULIC T ANK[...]

Saber Safety Section 1-24 SAFETY ITEM PART NO. QTY. DESCRIPTION 50023 AVAIL MANUAL CANISTER COMPLETE 1 00776031 1 ROUND MANUAL CANISTER 33997 1 DECAL, SHEET, MANUAL CANISTER 2 * DECAL 3 * DECAL 4 * DECAL 5 * AVAIL SPECIFIC PRODUCT MANUAL 6 33753 1 E M I SAFETY MANUAL 7 34296 1 FRONT ADHESIVE PAD 8 34297 1 REAR ADHESIVE PAD 9 6T1823 4 ZIP TIE 14” [...]

Saber Safety Section 1-25 SAFETY This section is intended to explain in broad terms the concept and effect of federal laws and regulations concerning employer and employee equipment operators. This section is not intended as a legal interpretation of the law and should not be considered as such . Employer-Employee Operator Regulations U.S. Public L[...]

Saber Safety Section 1-26 SAFETY[...]

ASSEMBL Y SECTION Assembly Section 2-1[...]

T6000 Saber Assembly Section 2-2 ASSEMBL Y CRANKSHAFT ADAPTER If necessary remove the four cap-screws from the crankshaft pulley . Then install the crankshaft adapter and spacer to the pulley with cap-screws and lock-washers as shown in the parts section. Before attempting to mount or service your Tiger mower , it is import ant to read and understa[...]

T6000 Saber Assembly Section 2-3 ASSEMBL Y JOYSTICK MOUNT ST AND Place the front edge of the support bracket 2 ¾” back from the lower right front window . Rotate stand to be 2 ¼” from the right door frame as shown below . Be sure that the location of the stand will allow clearance between the joystick and all existing interior levers, etc. Dr[...]

T6000 Saber Assembly Section 2-4 ASSEMBL Y SWITCH BOX MOUNTING (JOYSTICK) Locate the 2 holes in the right front corner of the cab frame. These will be the mounting holes for the 2 mounting bolts of the switch box bracket. Mount the bracket using the hardware supplied, as noted in the parts section. SWITCH BOX WIRING Refer to the Parts section for w[...]

T6000 Saber Assembly Section 2-5 ASSEMBL Y LIFT V A L VE MOUNT Install the valve mounting bracket to the inside of the right and left rear fender frame tube as shown below . Align the valve mounting plate with the drilled holes. Mark the center of one of the holes above and in line with the slotted holes in the valve plate. Do not use any holes tha[...]

T6000 Saber Assembly Section 2-6 ASSEMBL Y 4 CYLINDER EXHAUST MOUNT NOTE: This should be done after mounting the main frame. 1. Cut the tractor hood as shown in pic. # 1 to accomodate modified exhaust turbo tube. 2 Remove the muffler from existing turbo tube. 3. Remove existing turbo tube from tractor turbo. 4. Install the exhaust mounting bracket [...]

T6000 Saber Assembly Section 2-7 ASSEMBL Y Picture # 4 Picture # 5[...]

T6000 Saber Assembly Section 2-8 ASSEMBL Y 6 CYLINDER EXHAUST MOUNT NOTE: This should be done after mounting the main frame. 1. Cut the tractor hood as shown below to accomodate modified exhaust turbo tube. 2 Remove the muffler from existing turbo tube. 3. Remove existing turbo tube from tractor turbo. 4. Install the exhaust mounting bracket and su[...]

T6000 Saber Assembly Section 2-9 ASSEMBL Y MIRROR MOUNT 1. Remove the existing mirror bracket and mirror from the cab. 2 Remove the mirror and knob from existing bracket. 3. Install the supplied bracket (using supplied hardware) on the cab as shown below . 4. Install the mirror with the knob on the supplied bracket as shown below . Refer to the Par[...]

T6000 Saber Assembly Section 2-10 ASSEMBL Y NEW HOLLAND PRIORITY V AL VE USED ON DEL T A & V ALUE UNITS (HUSCO) The Delta and V alue units need a NH priority valve plug in the tractor rear remotes for the proper hydraulic flow . T orque the body fo the plug first to 94Nm and then the small end to 15Nm. The ports used are directly under the valv[...]

T6000 Saber Assembly Section 2-11 ASSEMBL Y DANFOSS PRIORITY V AL VE USED ON DEL T A & V ALUE UNITS The DanFoss lift valve needs a priority valve and a NH priority valve plug in the tractor rear remotes for the proper hydraulic flow . T orque the body fo the plug first to 94Nm and then the small end to 15Nm. The ports used are directly under th[...]

T6000 Saber Assembly Section 2-12 ASSEMBL Y POL Y -CARBONA TE SAFETY WINDOW NOTE: This should be done before mounting the main frame. 1. Disconnect gas shock at door . Remove the right side cab door from tractor cab by removing hinge pins. 2. Remove the existing hardware and discard factory glass door . 3. Place small bead of adhesive seal in the b[...]

T6000 Saber Assembly Section 2-13 ASSEMBL Y MAIN FRAME MOUNTING With an overhead hoist and / or jack-stands, raise one side of the frame up to the correctly matching mounting holes. Install cap-screws and all other hardware as shown in main frame parts section to secure the first side to the tractor casting. Next raise the second side of the frame [...]

T6000 Saber Assembly Section 2-14 ASSEMBL Y HAND RAIL MODIFICA TION The right side hand rail will need to be removed to allow room for the rear stowing boom to run along side the cab. T o remove the handrail, cut it of f at the top and bottom leaving approximately 2” on the tractor at each end. File the portions that are left to remove any sharp [...]

T6000 Saber Assembly Section 2-15 ASSEMBL Y INST ALLING O-RING FITTINGS Installing straight, 45 degree and 90 degree O-rings fittings requires that the O-ring, washer and nut (A) be up against the swivel body (B). Insert the swivel and turn in until the swivel is pointed in the right direction and the O-ring contact is made. Hold swivel in set dire[...]

T6000 Saber Assembly Section 2-16 ASSEMBL Y SABER HOSE ROUTING W ARNING NOTE: The sudden release of hydraulic pressure could cause the sudden movement of very heavy part s. Anyone in the way of these parts could be severely hurt or killed. DO NOT ALLOW these hydraulic hoses to BREAK or BURST in order to prevent hydraulic failure Make sure the hoses[...]

T6000 Saber Assembly Section 2-17 ASSEMBL Y Arrange the hoses in the clamp that attaches to the main frame as shown above, with the 1” motor hoses closest to the main frame. Pull the hoses snug from the swivel to the main frame clamps, when main boom is fully forward, and tighten the hoses in the clamp. Make sure the 1” motor hoses do not kink [...]

T6000 Saber Assembly Section 2-18 ASSEMBL Y[...]

T6000 Saber Assembly Section 2-19 ASSEMBL Y DECK A T T ACHMENT Attach the head to the secondary boom using the pins and hardware shown in the parts section to attach linkages. Install the square tube on the top of the head into the head mount and secure using the mounting plate and hardware as shown. The mount should be positioned to the left side [...]

T6000 Saber Assembly Section 2-20 ASSEMBL Y BOOM JOYSTICK CONTROL CALIBRA TION SUB-D This Danfoss PVG32 control valve is now equipped with higher-resolution actuators on Main Boom, Secondary Boom, Deck Roll, and Swivel functions. These actuators have “active fault monitoring”. The Deck Shield section does not have “active fault monitoring”.[...]

T6000 Saber Assembly Section 2-21 ASSEMBL Y Run tractor at normal operating RPM to adjust the settings as follows. Set the dead band compensation potentiometer first. Set the dead band compensation potentiometer at 50%, or halfway between full clockwise and full counter-clockwise. Setting Signal Adapt ation Potentiometers: Disconnect the Deutsch co[...]

T6000 Saber Assembly Section 2-22 ASSEMBL Y MAIN BOOM: “A” Port, Boom UP: 7-9 Seconds (Note: Extend secondary boom completely; roll deck to be level with ground, and lower main boom until deck is on ground. Now index main boom “up” function and determine the time required for main boom to rise completely .) “B” Port, Boom Down: 6-8 Seco[...]

T6000 Saber Assembly Section 2-23 ASSEMBL Y[...]

T6000 Saber Assembly Section 2-24 ASSEMBL Y 2WD FRONT AXLE ADJUSTMENT In order to prevent interference with mounted equipment, the front axle on a 2WD T6000 tractor will have to be adjusted outwards by 2 holes on each side (see illustration below). Double check the wheel spacing after adjustment by oscillating and turning the tires fully to check f[...]

T6000 Saber Assembly Section 2-25 ASSEMBL Y FINAL PREP ARA TION FOR OPERA TION Place operators safety and operation decals on the steering column and side counsel where they are clearly visible to the operator . These decals should be understood by each operator of the machine in conjunction with the safety and operation section of this book. The d[...]

T6000 Saber Assembly Section 2-26 ASSEMBL Y[...]

Operation Section 3-1 ©201 1 Alamo Group Inc. OPERA TION SECTION[...]

OPERATION Saber Operation Section 3-2 ©201 1 Alamo Group Inc. OPERA TION TIGER SABER BOOM MOWER OPERA TING INSTRUCTIONS Safety is of primary import ance to the owner/operator an d to the manufacurer . Ti ger Saber Booms are manufactured with quality material by skilled workers. The first sect ion of this manual includes a list of Safety Messages, [...]

OPERATION Saber Operation Section 3-3 ©201 1 Alamo Group Inc. OPERA TION 1.OPERA TOR REQUIREMENTS Safe operation of the unit is the responsibility of a qualifi ed operator . A qualified operator ha s read and understands th e implement and tractor Operator’s Ma nuals and is experienced in implem ent and tractor operation and all associated safet[...]

OPERATION Saber Operation Section 3-4 ©201 1 Alamo Group Inc. OPERA TION 2.TRACT OR REQUIREMENTS In addition to tractor horsepowe r and size required to operate th e boom unit, the tractor must also be pro perly equipped to provide operat or protecti on, to alert approaching vehicle drivers of the tractor ’ s presence, and to ensure tractor stab[...]

OPERATION Saber Operation Section 3-5 ©201 1 Alamo Group Inc. OPERA TION 2.3 T ractor Lighting and SMV Emblem If the tractor will be operated near or traveled on a public roadw ay it must be equipped wit h proper warning lighting and a Slow Mo ving V ehicle (SMV) emblem which ar e clearly visible fro m the rear of the unit. Most tractor’s have d[...]

OPERATION Saber Operation Section 3-6 ©201 1 Alamo Group Inc. OPERA TION 3.GETTING ON AND OFF THE TRACT OR Before getting o nto the tractor , the operato r must read and comple tely understand the implement and tractor operator manuals. If any p art of either manual is no t completely understood, consult an author ized dealer for a complete explan[...]

OPERATION Saber Operation Section 3-7 ©201 1 Alamo Group Inc. OPERA TION BEFORE leaving the tracto r seat, alw ays set th e parking brake a nd/or set the tractor transmission in parking ge ar , disengage the PTO, stop the engine, remove the key , and wait for all movin g parts to stop. Place the tractor shift lever into a low range or par king gea[...]

OPERATION Saber Operation Section 3-8 ©201 1 Alamo Group Inc. OPERA TION When rot ating part s are in motion, serious injury may occur if caution is n ot used or danger is not recognized. Never allow byst anders with 300 yards of the machine when mower is in operation. Be sure the ball valve on the mower hydraulic t ank are OPEN before sta rting t[...]

OPERATION Saber Operation Section 3-9 ©201 1 Alamo Group Inc. OPERA TION 5.2 Boom Unit Pre-Operati on Inspection and Service Inspect and service the boom arm and head prior to operation. Damaged and/or broken p arts should be repaired and/or replaced immedi ately . T o ensure the unit is ready for oper ation, conduct the following: OPS-B- 0020 5.1[...]

OPERATION Saber Operation Section 3-10 ©201 1 Alamo Group Inc. OPERA TION FRAME ASSEMBL Y • Inspect condition of mounting frame weldment. • Inspect condition of Swivel Assy . • E n sur e all bolts and screw s are in pos itio n an d ar e properly torqued. • Ensure all pins are in place and fastened with screws. • Ensure frame is properly [...]

OPERATION Saber Operation Section 3-11 ©201 1 Alamo Group Inc. OPERA TION BOOM ARM ASSEMBL Y • Inspect condition of each arm section weldment • E ns ur e all pin s ar e in pla ce . • E ns ur e all bo lts, nuts and rollpins are pr op e rly installed. • Check condition of bushings at boom pivot points and hydr aulic cylinder tangs. • Ensur[...]

OPERATION Saber Operation Section 3-12 ©201 1 Alamo Group Inc. OPERA TION HYDRAULIC PUMP/OIL RESERVOIR • Chec k oil reservoir leve l and oil condition. (Add specific type oil if low) • Change hydraulic oil filter and hydraulic oil according to mainte nance schedule. • E nsure ther e are no oil leaks an d fitting are properly connected • In[...]

OPERATION Saber Operation Section 3-13 ©201 1 Alamo Group Inc. OPERA TION ROT AR Y HEAD INSPECTION • Inspect blades and bl ade bolts for looseness and excessive wear . R otate to 90° to make for checking easier . Re place damaged, worn, and missing blades as complete set s to maintain rot ary balance. • Ensure motor bolt s and nuts are tighte[...]

OPERATION Saber Operation Section 3-14 ©201 1 Alamo Group Inc. OPERA TION Boom PRE-OPERA TION Inspection Mower ID#________________ Make ____________________ Date: ________________ Shift ____________________ Before conductin g the inspection, make s ure the tractor engine is off, all rot ation has stopped and the tractor is in p ark with the p arki[...]

OPERATION Saber Operation Section 3-15 ©201 1 Alamo Group Inc. OPERA TION T ractor PRE-OPERA TION Inspection Mower ID#________________ Make ____________________ Date: ________________ Shift ____________________ Before conducting the inspection, make sure the tr actor engine is off, all rot ation has stopped and the trac tor is in par k with the pa[...]

OPERATION Saber Operation Section 3-16 ©201 1 Alamo Group Inc. OPERA TION 5.3 Cutting Component Inspection Inspect blade p an and blade assembly for the following: OPS-U-0031 Inspect the Blades daily for abnormal wear . REPLACE BOTH BLAD ES on that carrier IMMEDIA TEL Y if either blade has: • Become bent or deformed from it’s original shape or[...]

OPERATION Saber Operation Section 3-17 ©201 1 Alamo Group Inc. OPERA TION 5.4 Blade Bolt Inspection Inspect Blade Bolt Head da ily for wear as followed: Inspect the Blade Bolt Heads d aily for abn ormal wear . REPLACE BOTH BLADE BOL TS on the Blades IMMEDIA TEL Y if either blade bolt s has: • Visible cracks or • If the reces sed area o n blade[...]

OPERATION Saber Operation Section 3-18 ©201 1 Alamo Group Inc. OPERA TION 6.JOYSTICK CONTROL[...]

OPERATION Saber Operation Section 3-19 ©201 1 Alamo Group Inc. OPERA TION JOYSTICK FW/BACK MOVES MAIN BOOM JOYSTICK LEFT/RIGHT MOVES SECONDARY BOOM LEFT JOYSTICK ROLLE R MOVES DECK ROLL[...]

OPERATION Saber Operation Section 3-20 ©201 1 Alamo Group Inc. OPERA TION RIGHT JOYSTICK ROLLER MOVES BOOM SWIVEL SHIELD SWITCH(on switch box) OPERA TES SAFETY SHIELD 6.1 Switchbox The Safety Shield lever opens and closes the shield located on the fron t of the cutter head. When moving at or near the ground, always have th e shield in the c losed [...]

OPERATION Saber Operation Section 3-21 ©201 1 Alamo Group Inc. OPERA TION Check to make sure mo wer switch is in the “OFF” posit ion. The unit is designed not to start if the switch is in the “ON” position. If tr actor starts with switch on, tu rn off tractor and conta ct your local T iger dealership for assist ance. S tart the tractor and[...]

OPERATION Saber Operation Section 3-22 ©201 1 Alamo Group Inc. OPERA TION 6.2 Main Control Switch Box The Mower Control switch turns the mower “ON” and “OFF”. This switch is to be in the “OFF” position to start the tractor . If the switch is “O N” and the tractor ignition switch is tur ned to “ON” the red “mower run” indica[...]

OPERATION Saber Operation Section 3-23 ©201 1 Alamo Group Inc. OPERA TION The Master Switch a lso provides power to the “Deck Fl oat”, “Shield” a nd “T ravel Lock” Functions of the mower deck. The Deck Float function allows the ground roller of the flail mower head to follo w the contour of the ground. T o operate the deck float functi[...]

OPERATION Saber Operation Section 3-24 ©201 1 Alamo Group Inc. OPERA TION 7.DRIVING THE TRAC TOR AND IMPLEMENT Safe tractor transport req uires the operator to po ssess a thorough knowledge of the m odel being operated and precaution s to take while driving with a n attached implement. Ensure the trac tor has the ca pacity to handle the weight of [...]

OPERATION Saber Operation Section 3-25 ©201 1 Alamo Group Inc. OPERA TION T ransport on ly at speeds where you can maintain control of the equipment. Seriou s accidents and injuries can result from oper ating this equipment at high sp eeds. Unders tand the Tr actor and Implement and how it handles before transporting on street s and high ways. Mak[...]

OPERATION Saber Operation Section 3-26 ©201 1 Alamo Group Inc. OPERA TION 7.2 Brake and Differential Lock Setting Make sure the tr actor brakes are in good oper ating condition. T ractor brakes can be set to operate independently allowing sin gle rear wheel braking action or locked together to provide simult aneous rear wheel braking. FOR MOST DRI[...]

OPERATION Saber Operation Section 3-27 ©201 1 Alamo Group Inc. OPERA TION 7.3 Driving the T ractor and Boom S tart off driving at a slo w speed and gradually increase your speed while maintainin g comple te control of the tractor . N ever operate the tractor at speeds that cannot be safely handled or which will prevent the operator from stopping q[...]

OPERATION Saber Operation Section 3-28 ©201 1 Alamo Group Inc. OPERA TION 8.OPERA TING THE BOOM UNIT AND A TT ACHED HEAD THE OPERA TOR MUST COMPLETEL Y UNDERST AND HOW TO OPERA TE THE TRACTOR AND MOWER AND ALL CONTROLS BEFORE A TTEMPTING TO MOW . The operator must read an d underst and the Safety and Oper ation Sections of this manual an d the tra[...]

OPERATION Saber Operation Section 3-29 ©201 1 Alamo Group Inc. OPERA TION 8.1 Foreign Debris Hazards/Overhead Obstructions An area to be cut must first be inspe cted for objects that co uld be thrown or that could damage the machine. W alk through the area loo king for fences, boulders, rocks, culverts, stumps or metal object s. Mark the inspected[...]

OPERATION Saber Operation Section 3-30 ©201 1 Alamo Group Inc. OPERA TION 8.3 Mower Operation The rot ating part s in this machine have been designed and teste d for rugged use. However , they could fail upon imp act with heavy solid object s-such as steel guard rails, con crete abutments,etc., causing them to be thrown at a very high velocity . N[...]

OPERATION Saber Operation Section 3-31 ©201 1 Alamo Group Inc. OPERA TION A flail mower deck should be carried so that the p art of the deck weight is carried by the boom and part carried by the groun d roller , when moving on the ground. When the flail mower is carried this way , the ground roller follows the contour of the ground more easily dur[...]

OPERATION Saber Operation Section 3-32 ©201 1 Alamo Group Inc. OPERA TION disengage the mowe r , and return boom to a safe travel position. Return to st arting point and make next p ass, etc. After the first d ay of operation, all bolt s should be checked and tightened securely . This should be done periodically to ensure the bolt s do not b ecome[...]

OPERATION Saber Operation Section 3-33 ©201 1 Alamo Group Inc. OPERA TION 8.6 50” Boom Flail The 50” boom flail mower was designed for cutting brush and folia ge up to 2 inch es in diame ter or multiple branches that have a total cross section area equivalent to on e 2 inch branch. Cuttin g multiple limbs at the same time may overlo ad the mow[...]

OPERATION Saber Operation Section 3-34 ©201 1 Alamo Group Inc. OPERA TION 8.8 Saber Flail The Saber flail mower was designe d for cutting brush and foliage up to 4 inches in dia meter or multiple branches that have a tota l cross secti on area equivalent to one 4 inch br anch. Cutting multip le limbs at the same time may overload the mower cau sin[...]

OPERATION Saber Operation Section 3-35 ©201 1 Alamo Group Inc. OPERA TION 8.10 Shutting Down the Att ached Head- For S t a ndard Equipment T o shut down att ached mower head, first bring the tractor to a complete stop. Decrease engin e RPM to idle then disengage cutterhea d. The mower head will come to a complete stop within a suitable amount of t[...]

OPERATION Saber Operation Section 3-36 ©201 1 Alamo Group Inc. OPERA TION 9.1 Unstowing the Boom T o un-stow the boom from the boom re st, proceed as follows. Extend secondary boom “OUT” an d move main boom “UP” of f of horizonta l support. Swivel boom “FOR W ARD” perpendicular to tractor and switch travel lock to “OFF” (ONL Y FOR [...]

OPERATION Saber Operation Section 3-37 ©201 1 Alamo Group Inc. OPERA TION 9.3 T ransporting on Public Roadways Extreme caution should be used when transporting th e tractor and mower on public roadways. The tractor must be equip ped with all required safety warnin g features including a SMV emb lem and flashing war ning lights to alert drivers of [...]

OPERATION Saber Operation Section 3-38 ©201 1 Alamo Group Inc. OPERA TION When operating on public roa ds, have consideration for other r oad users. Pull to the side of the road oc casionally to allow all following traffic to pass. Do no t exceed the legal speed limit set in your state or muni cipality for agricultural tractors. Always stay alert [...]

OPERATION Saber Operation Section 3-39 ©201 1 Alamo Group Inc. OPERA TION 9.4 T ransporting Unit by Flatbed T railer Park flatbed on leve l area. Drive tra ctor onto ce nter of flatbed to avoid uneven distri b ution of weight and st aying within local width restricti ons. If boom is over local height re strictions, you will need to extend booms ou[...]

OPERATION Saber Operation Section 3-40 ©201 1 Alamo Group Inc. OPERA TION 10. TRACTO R, BOOM, AND A TT ACHED HEAD STORAGE Properly prep aring and storing th e unit at the end of the season is critical to maint aining its appearance and to help ensure years of dep endable service. The following are suggested storag e procedures: • Thoroughly clea[...]

OPERATION Saber Operation Section 3-41 ©201 1 Alamo Group Inc. OPERA TION BEFORE leaving the tracto r seat, alw ays set th e parking brake a nd/or set the tractor transmission in parking ge ar , disengage the PTO, stop the engine, remove the key , and wait for all movin g parts to stop. Place the tractor shift lever into a low range or par king ge[...]

OPERATION Saber Operation Section 3-42 ©201 1 Alamo Group Inc. OPERA TION[...]

Maintenanc e Sec tio n 4- 1 ©201 1 Alamo Group Inc. MAINTENANCE SECTION[...]

MAINTENANCE Saber Maintenance Section 4-2 ©201 1 Alamo Group Inc. MAINTENANCE General Instructions T iger Mowers are designed for high pe rformance and rugged durability , ye t with simplified maintenance. The purpose of this section of the manual is to help the operator in the reg ular serv icing of the mo wer . Regular maintenance at the interva[...]

MAINTENANCE Saber Maintenance Section 4-3 ©201 1 Alamo Group Inc. MAINTENANCE whenever a whee l is removed an d rein stalled. Regular Maintenance The intervals at which regular servicing should be do ne are based on ho urs o f oper ation . Use th e tractors h our meter to determine when reg ular servicing is required. Daily or Every 8 Hours ITEM S[...]

MAINTENANCE Saber Maintenance Section 4-4 ©201 1 Alamo Group Inc. MAINTENANCE ITEM SERVICE COMMENTS Hydraulic Fittings Check for leaks T ighten when needed. Do Not use hands to check for leaks, see maintenance precautions Knives Check Inspect for missing or damaged knives, change as needed or sharpen as needed. S pindle mounting bolts Check 3/4”[...]

MAINTENANCE Saber Maintenance Section 4-5 ©201 1 Alamo Group Inc. MAINTENANCE WEEKL Y OR EVER Y 40 HOURS ITEM SERVICE COMMENTS Rotary S p indle Lubricate Every 40 hour s or week ly WEEKL Y OR EVER Y 50 HOURS ITEM SERVICE COMMENTS In T ank Hyd. Fluid Change Change afte r first 50 hours only , then Filter every 500 hrs. yearly or if indicated by 10 [...]

MAINTENANCE Saber Maintenance Section 4-6 ©201 1 Alamo Group Inc. MAINTENANCE TROUBLESHOOTING SYMPTOMS CAUSE REMEDY Vib r at i o n 1. Loose Bolts 1. Check all bolts and tighten to recommended torque specifications 2. Cutter assembly 2a. Check for damage blades, disc Unbalanced or cutter shaft. Replace if needed. 2b. Check for wire , rope, etc. ent[...]

MAINTENANCE Saber Maintenance Section 4-7 ©201 1 Alamo Group Inc. MAINTENANCE TROUBLESHOOTING (Continued) SYMPTOMS CAUSE REMEDY Motor runs but 1. Belts 1. Inspect belts and pulleys. Replace will not cut . belts and rep air as needed. 2. T ensioner 2. Adjust tensioner nut flat washer washer is flush with top of guide. Mower turns slowly 1. Contamin[...]

MAINTENANCE Saber Maintenance Section 4-8 ©201 1 Alamo Group Inc. MAINTENANCE LUBRICA TION RECOMMENDA TIONS Description Application General S pecification R ecommended Mobil Lubricant T ractor Hydraulics Reserv oir JD-20C Mobilfluid® 424 Mower Hydraulics Reservoir Cold T emperatures 0° F ISO 46 Anti-Wear -Low T emp Mobil DTE® 15M St a r t - U p[...]

MAINTENANCE Saber Maintenance Section 4-9 ©201 1 Alamo Group Inc. MAINTENANCE T ORQUE SPECIFICA TIONS *These are general specifications. Check your tractor operato rs or service manual for exact specifi ca tions.[...]

MAINTENANCE Saber Maintenance Section 4-10 ©201 1 Alamo Group Inc. MAINTENANCE POL Y CARBONA TE CARE & MAINTENANCE The propriet ary UV and Abrasio n Resistant Surfac e coating on SHIELD S® SUPERCOA TED™ polycarbonate significantly improves performa nce. Periodic cleaning using proper proc edures and comp atible cleaners are recommended to p[...]

MAINTENANCE Saber Maintenance Section 4-11 ©201 1 Alamo Group Inc. MAINTENANCE RECOMMENDED FILLING INSTR UCTIONS FOR HYDRAULIC RESER VIORS When filling or checking the oil level, the unit should be parked on a level su rface., shut ” OFF”, and allow suff icient time to cool to ambient tempera ture. Use caution when removing th e pressur ized b[...]

MAINTENANCE Saber Maintenance Section 4-12 ©201 1 Alamo Group Inc. MAINTENANCE DET AILED MAINTENANCE REPLACEING HIGH PRESSURE HYDRAULIC FIL TER ELEMENT : Assure system has been shut d own and de- pressurized. Locate High Pres sure Filter housing. Confirm that the element that is about to be installed matches the ele ment p/n o n the filter model t[...]

MAINTENANCE Saber Maintenance Section 4-13 ©201 1 Alamo Group Inc. MAINTENANCE GREASING GROUND ROLLER SHAFT -FLAIL Locate grease zerks on ea ch end of rolle r tube at lo wer end of head. Normal conditio ns require one or two pump in each bearing, using Lithiu m-Complex Extreme Pressure grease conforming to NLGI2- ISO 320 specifications. This is to[...]

MAINTENANCE Saber Maintenance Section 4-14 ©201 1 Alamo Group Inc. MAINTENANCE BALL V AL VES The ball valve at the h ydraulic reservoir may nee d to be closed during cert ain maintenance or repa ir procedures. THE BALL V AL VES MUST BE OPEN (handle p arallel with va lve) WHEN TRACTOR IS RE-ST ARTED OR PUMP IS COUPLED TO MOTOR OR P .T .O.! Failure [...]

MAINTENANCE Saber Maintenance Section 4-15 ©201 1 Alamo Group Inc. MAINTENANCE GREASING POINTS ON BOOM AND PIVOT Locate grease ze rks (8) on deck pivot assembly , (2) on the deck end of secondary boom, (2 ) at main/ secondary boom joint, and (2) a t swivel end of main boom. Inject Lithium-Complex Extreme Pr essure grease conforming to NLGI2-ISO 32[...]

MAINTENANCE Saber Maintenance Section 4-16 ©201 1 Alamo Group Inc. MAINTENANCE DECK ST OP ADJUSTMENT Loosen locking nut. T urn adjustment bolt in, and run deck cylinder out to full ex tension. Adjust bolt out until the head just touches the boom , and tighten lock nut. NOTE: Bolt should not hit boom before cylinder reaches full travel. GREASING SP[...]

MAINTENANCE Saber Maintenance Section 4-17 ©201 1 Alamo Group Inc. MAINTENANCE TIGHTENING SPINDLE BOL TS The spindle mounting bolts shoul d be checked and retorqued daily or every 10 hours of service. T orque the (6) bolts shown be low to 331 ft. lbs. GREASING PUMP DRIVE SHAFT COUPLER With engine stopped, ensur e drive shaft alignm ent by grasping[...]

MAINTENANCE Saber Maintenance Section 4-18 ©201 1 Alamo Group Inc. MAINTENANCE DRIVE SHAFT YOKE, U-JOINT 7STUB SHAFT With engine stopped, in ject Lithium-Complex extreme pr essure grea se confirm ing to NLGI2- ISO 320 specifications into univ ersal joints and slip yoke until grease appears at the se al. Grease them daily or every 8 hours. GREASING[...]

MAINTENANCE Saber Maintenance Section 4-19 ©201 1 Alamo Group Inc. MAINTENANCE GREASING BOOM CYLINDER(S) PIVOT POINTS Locate the zerk on the butt end t ang of cylinder an d on rod end t ang. Inject Lithium-Complex Extreme Pressure grease confir ming to NLGI2-ISO 320 specifications until grease begins to protrude fro m ends. This proce dure is to b[...]

MAINTENANCE Saber Maintenance Section 4-20 ©201 1 Alamo Group Inc. MAINTENANCE Blades Check the Blades for cracks and w ear and Blade Bolts for tightness, daily . Blades should be replaced when they are worn excessively , bent, deformed, or out of balance. Blades should always be replac ed in pairs. Bl ade s of different weight s can cause serious[...]

MAINTENANCE Saber Maintenance Section 4-21 ©201 1 Alamo Group Inc. MAINTENANCE ROT AR Y KNIFE REPLACEMENT 1. Be sure you have a complete matching set of new knives for replacement. 2. Remove knives and inspect holes for damage. Also watch for cracks in the disk around the ho les. 3. Lube threads with anti- seize, motor oil or grease. Inst all bolt[...]

MAINTENANCE Saber Maintenance Section 4-22 ©201 1 Alamo Group Inc. MAINTENANCE Flail Blades Inspection Inspect the Blades daily for abno rmal wear . REPLACE ALL BLADES on the carrier IMMEDIA TEL Y if any blades have: • Become bent or deformed from its origin al shap e, or • Wear inside the blade bolt h ole, or • A ny crac ks ar e visib le, o[...]

MAINTENANCE Saber Maintenance Section 4-23 ©201 1 Alamo Group Inc. MAINTENANCE Blade Pins and D-Ring Inspection Blade Pins and D-Rings daily for wear or dam age as follows: Inspect the Blade pins and D-Ring s daily for abnormal wear . Make sure the cotter pins are in place and properly spread . REPLACE BLAD E Pins and D-Rings IMMEDIA TEL Y if they[...]

MAINTENANCE Saber Maintenance Section 4-24 ©201 1 Alamo Group Inc. MAINTENANCE Flail Axe Blades Inspection Inspect the Blades daily for abno rmal wear . REPLACE ALL BLADES on the carrier IMMEDIA TEL Y if any blades have: • Become bent or deformed from its origin al shap e, or • Oval shape wear inside the blade bolt hole, or • A ny crac ks ar[...]

MAINTENANCE Saber Maintenance Section 4-25 ©201 1 Alamo Group Inc. MAINTENANCE 50” FLAIL KNIFE BLADE REPLACEMENT 1. If knives are damaged or badly wo rn, they will need to be replaced as a set. Replacing a single knife can cause severe vibration and possible da mage to th e mower . The knife should not be welded on for any reason. 2. Always repl[...]

MAINTENANCE Saber Maintenance Section 4-26 ©201 1 Alamo Group Inc. MAINTENANCE DO NOT re-use the locking hex nut s for mounting the knives. If hex nut become s loose, or requir ed removal for knife replacement or any other reason, they must b e discarded and replaced with new nuts. 63” BOOM FLAIL KNIFE REPLACEMENT 1. If knives are damaged or bad[...]

MAINTENANCE Saber Maintenance Section 4-27 ©201 1 Alamo Group Inc. MAINTENANCE 6. Apply grease to seal of ou ter bearing cover assemblies 7. Remove two (2 ) nuts securing the be aring asse mblie s. Carefully install oute r bearing cover assemblies (with integral seals), and secure with six (6) bo lts and locknut s. 8. Grease bearing s with grease [...]

MAINTENANCE Saber Maintenance Section 4-28 ©201 1 Alamo Group Inc. MAINTENANCE BEARING INST ALLA TION 1. Press upper bea ring cup into the spindle housing 2. T urn the sp indle housing over and pr ess in the lower bearing cup. 3. Place the lower bear ing cone in the bearing cup. Next press the seal into the spindle housing. The in ner lip of the s[...]

MAINTENANCE Saber Maintenance Section 4-29 ©201 1 Alamo Group Inc. MAINTENANCE Boom Cylinder Removal and Replacement Instructions 1. Clear the ar ea of all personnel before lowering the boom mower head. 2. From the tractor seat with your seat belt fast ened around you, Lo wer the boom mower head to the ground. Extend the boo m to the fu rthest rea[...]

MAINTENANCE Saber Maintenance Section 4-30 ©201 1 Alamo Group Inc. MAINTENANCE CUTTERSHAFT BEARING REPLACEMENT 1. Remove existing cuttershaft, be arings and string guards. 2. Make sure that the end knives on each end of the cuttershaft are orient ated as shown. 3. Apply anti-seize on cuttershaf t as shown on next page. 4. Install non-drive side be[...]

MAINTENANCE Saber Maintenance Section 4-31 ©201 1 Alamo Group Inc. MAINTENANCE[...]

MAINTENANCE Saber Maintenance Section 4-32 ©201 1 Alamo Group Inc. MAINTENANCE DAIL Y MAINTENANCE SCHEDULE The following services should be perform ed daily or every 8 hours of service, following the detaile d maintenance instructions in th e operators manual. _______ Pump Drive Shaft: If r equired with drive shaf t/coupler check for end play and [...]

P ARTS SECTION NEW HOLLAND T6000 SABER Parts Section 5-1[...]

CNH T6000 Saber Parts Section 5-2 The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this manual. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are giv[...]

CNH T6000 Saber Parts Section 5-3 P ARTS SECTION T ABLE OF CONTENTS SECTION P A G E TRACTOR MOUNT KIT – MAIN FRAME 5-4 TRCTR MNT KIT – HYD BRAKE V AL V E 5-6 AXLE BRACE & BA TTER Y BOX 5-8 JOYSTICK AND SWITCH BOX 5-10 L V -5 SP DANFOSS, LOAD SENSE 5-12 L V -5 SP DANFOSS, LOAD SENSE,TERRA GLIDE 5-14 L V -5 SP DANFOSS, POWER BEYOND,DEL T A 5-[...]

CNH T6000 Saber Parts Section 5-4 TRACTOR MOUNT KIT - MAIN FRAME[...]

CNH T6000 Saber Parts Section 5-5 TRACTOR MOUNT KIT - MAIN FRAME ITEM P /N QTY . DESCRIPTION 1 06300076 1 FRM,LH,T6030,SBR 2 06300075 1 MNFRM,T6030,SBR 3 06300080 1 MNT ,T ANK,NHT6010 4 06380012 1 T ANK,RES,JD60004WD(34GAL) 5 31004 1 CA P ,PRESSURE,3.0PSI,3/4MP 6 21725 6 HEX NUT ,1/2 NC 7 22018 2 FL ATW ASHER,1/2,WIDE 8 06505067 1 SIGHT GAUGE,JD600[...]

CNH T6000 Saber Parts Section 5-6 TRCTR MNT KIT - HYDRAULICS, BRAKE V A L VE[...]

CNH T6000 Saber Parts Section 5-7 TRCTR MNT KIT - HYDRAULICS, BRAKE V A L VE ITEM P/N QTY . DESCRIPTION 1 06300076 1 FRM,LH,T6030,SBR 2 06300075 1 MNFRM,T6030,SBR 3 06300080 1 MNT , T ANK,NHT6010 4 06700090 1 T ANK ASSY 5 23152 1 PUMP ,P350-1 3/4 GEAR 6 TF4852 2 K I T ,FLANGE,#20 7 064001 14 1 M N T ,BRAKE V AL VE,TSA 8 33880 2 F L ATW ASHER,3/4,GR[...]

CNH T6000 Saber Parts Section 5-8 AXLE BRACE - SABER[...]

CNH T6000 Saber Parts Section 5-9 AXLE BRACE - SABER ITEM PART NO. QTY. DESCRIPTION 1 * R EF MAIN FRAME - REFER T O TRACTOR MNT P AGE 2 06300032 1 AXLE BRC,LH,NHTSA 3 06300031 1 AXLE BRC,RH,NHTSA 4 21825 4 HEX NUT ,3/4,NC 5 33880 8 F L ATW ASHER,3/4,GR 8,SAE 6 21833 4 CAPSCREW ,3/4 X 2-1/4,NC 7 22016 8 F L ATW ASHER,3/8,GR8 8 21627 4 NYLOCK NUT ,3/[...]

CNH T6000 Saber Parts Section 5-10 JOYSTICK AND SWITCH BOX[...]

CNH T6000 Saber Parts Section 5-11 ITEM PART NO. QTY. DESCRIPTION 1 06520041 2 MOUNT ,RAM,BALL,1 1/2",NPT ,2181 2 06520042 1 MOUNT ,RAM,ARM,1.5"x2.75",SHORT 3 35033 1 CAN,JYSTK,CPL T ,DF 4 35205 1 SETSCREW ,3/8 x 2 NC,KNURLED PT 5 35206 1 HEX NUT ,JAMB,3/8 NC 6 35204 1 KNOB,3/8 NC,INSERT 7 33691 1 JOYST ,4AXIS,RH,DF ,W/SUB-D CONN 8 3[...]

CNH T6000 Saber Parts Section 5-12 LIFT V AL VE - 5 SP DANFOSS[...]

CNH T6000 Saber Parts Section 5-13 LIFT V A L VE - 5 SP DANFOSS ITEM P ART NO. Q TY DESCRIPTION 1 06340008 1 V L V M N T ,RH,TSA1 15 2 06340009 1 V L V M N T ,LH,TSA1 15 3 34622 1 P L A TE,V AL VE,REAR MNT 4 21631 4 CAPSCREW 3/8” X 1-1/4” 5 21988 4 LOCKWASHER,3/8 6 21625 4 HEX NUT ,3/8 NC 7 22016 3 F L A T W ASHER,3/8 8 06505029 1 FI L TER,HP ,[...]

CNH T6000 Saber Parts Section 5-14 LIFT V AL VE - 5 SP DANFOSS - TERRA GLIDE[...]

CNH T6000 Saber Parts Section 5-15 LIFT V AL VE - 5 SP DANFOSS - TERRA GLIDE ITEM P ART NO. Q TY DESCRIPTION 1 06340008 1 V L V M N T ,RH,TSA1 15 2 06340009 1 V L V M N T ,LH,TSA1 15 3 34622 1 P L A TE,V AL VE,REAR MNT 4 21631 4 CAPSCREW 3/8” X 1-1/4” 5 21988 4 LOCKWASHER,3/8 6 21625 4 HEX NUT ,3/8 NC 7 22016 3 F L A T W ASHER,3/8 8 06505029 1 [...]

CNH T6000 Saber Parts Section 5-16 LIFT V AL VE - 5 SP DANFOSS - DEL T A[...]

CNH T6000 Saber Parts Section 5-17 LIFT V AL VE - 5 SP DANFOSS - DEL T A ITEM P ART NO. Q TY DESCRIPTION 1 06340008 1 V L V M N T ,RH,TSA1 15 2 06340009 1 V L V M N T ,LH,TSA1 15 3 34622 1 P L A TE,V AL VE,REAR MNT 4 21631 4 CAPSCREW 3/8” X 1-1/4” 5 21988 4 LOCKWASHER,3/8 6 21625 4 HEX NUT ,3/8 NC 7 22016 4 F L A T W ASHER,3/8 8 06505029 1 FI L[...]

CNH T6000 Saber Parts Section 5-18 MIRROR BRACKET[...]

CNH T6000 Saber Parts Section 5-19 MIRROR BRACKET ITEM PART NO. QTY. DESCRIPTION 1 * 1 WORK LIGHT 2 * 1 KNOB T6010 3 * 1 MIRROR 4 * 1 EXHAUST 5 06370008 1 MNT ,MIRROR/LIGHT ,TS1 15A 6 06410633 1 MNT ,MIRROR,T6010 7 06410141 1 COLLAR,EXHAUST ,TS1 15A 8 06410142 1 COLLAR,CLAMP ,EXHAUST ,TS1 15A 9 21530 2 CAPSCREW ,1/4" X 1" NC 1 0 21525 4 H[...]

CNH T6000 Saber Parts Section 5-20 EXHAUST MOUNT - 4 CYLINDER ITEM PART NO. QTY. DESCRIPTION 1 06410127 1 MNT ,EXHAUST ,TSA100-1 10 2 21630 4 CAPSCREW ,3/8 x 1,NC 3 21625 4 HEX NUT ,3/8,NC 4 21988 4 LOCKWASHER,3/8 5 * 2 EXISTING MAINFRAME HARDWARE 6 06410128 1 MNT ,EXHAUST ,SUPPORT 7 35188 2 CLAMP ,EXHAUST ,3” 8 06520024 1 TUBE,EXHAUST ,SUPPOR T [...]

CNH T6000 Saber Parts Section 5-21 EXHAUST MOUNT - 6 CYLINDER ITEM PART NO. QTY. DESCRIPTION 1 064101 13 1 MNT ,EXHAUST ,TSA1 15-135 2 06410121 1 MNT ,EXHAUST ,SUPPOR T ,TSA1 15-135 3 06520023 1 TUBE,EXHAUST RELOCA TE,TSA,6CYL 4 32986 2 CLAMP ,EXHAUST ,3 1/2 5 21630 4 CAPSCREW ,3/8x1,NC 6 21988 4 LOCKWASHER,3/8 7 21625 4 HEX NUT ,3/8 NC 8 * 2 EXIST[...]

CNH T6000 Saber Parts Section 5-22 BOOM POL YCARBONA TE CAB SAFETY WINDOW KIT[...]

CNH T6000 Saber Parts Section 5-23 ITEM PART NO. QTY. DESCRIPTION 1 06490004 1 PO L YCARBONA TE, HNTSA 1 15, DOOR, RH 2 31965 1 7’ TRIM SEAL, 3/8 CLIP X 3/4 OD BULB 3 06530502 2 CAPSCREW 8 MM X 40 MM GR8 4 * * EXISTING HARDWARE 5 06530501 1 CAPSCREW 6 MM X 25 MM GR8 6 06537006 1 THREADED INSERT 1/4 X 1/2 NC 7 21532 1 CAPSCREW , 1/4X1-1/2 NC 8 065[...]

CNH T6000 Saber Parts Section 5-24 WHEEL WEIGHT SABER[...]

CNH T6000 Saber Parts Section 5-25 34" TIRE CONFIGURA TION ITEM P ART NO. QTY . DESCRIPTION 1 32615 1 1700# WEIGHT 2 32518 2 850# WEIGHT 3 21846 3 CAPSCREW ,3/4 x 9,NC 4 33626 3 F L ATW ASHER,3/4,GR 8,USS 5 06530200 3 CAPSCREW ,7/8 x 14,GR 8,NC 6 06533000 6 F L A T W ASHER,7/8,GR 8 7 06531000 3 HEX NUT ,7/8,GR 8,NC WHEEL WEIGHT SABER 38" [...]

CNH T6000 Saber Parts Section 5-26 WHEEL WEIGHT - SABER MB/XB[...]

CNH T6000 Saber Parts Section 5-27 34" TIRE CONFIGURA TION ITEM P ART NO. QTY . DESCRIPTION 1 32615 1 1700# WEIGHT 2 32518 3 850# WEIGHT 3 21846 3 CAPSCREW ,3/4 x 9,NC 4 33626 3 F L ATW ASHER,3/4,GR 8,USS 5 06530200 3 CAPSCREW ,7/8 x 14,GR 8,NC 6 06533000 6 F L A T W ASHER,7/8,GR 8 7 06531000 3 HEX NUT ,7/8,GR 8,NC WHEEL WEIGHT - SABER MB/XB 3[...]

CNH T6000 Saber Parts Section 5-28 OPTIONAL PUMP AND GRILL GUARD KIT ITEM PART NO. QTY. DESCRIPTION 1 32430 1 UNIVERSAL PUMP GUARD 2 32737 1 UNIVERSAL GRILL GUARD 3 21833 4 CAPSCREW - 3/4 X 2 1/4 4 22021 2 FLATWASHER - 3/4 5 21993 4 LOCKWASHER - 3/4 6 21825 4 HEX NUT - 3/4[...]

CNH T6000 Saber Parts Section 5-29 ITEM PART NO. QTY. DESCRIPTION 1 06310071 1 BMRST,ASSY,SABER 2 06310090 1 STOP,UPPER,CNH,SBR 3 06310091 1 STOP,LOWER,CNH,SBR 4 06520078 4 BUMPER,PAD,SHORT 5 32686 1 BUMPER,PAD,LONG 6 28734 11 CAPSCREW,3/8 x 1,NC 7 6T1027 8 CAPSCREW,1/2 x 1-3/4,GR8,NC 8 06533004 1 6 FLATWASHER,1/2,GR8,NC 9 31580 8 HEX NUT,1/2,GR8,N[...]

CNH T6000 Saber Parts Section 5-30 BOOMREST ASSEMBL Y - SABER MB ITEM PART NO. QTY. DESCRIPTION 1 06310092 1 BMRST,ASSY,SABER MB 2 06310090 1 STOP,UPPER,CNH,SBR 3 06310060 1 STOP,LOWER,SBR MB 4 06520078 4 BUMPER,PAD,SHORT 5 32686 1 BUMPER,PAD,LONG 6 28734 11 CAPSCREW,3/8 x 1,NC 7 6T1027 8 CAPSCREW,1/2 x 1-3/4,GR8,NC 8 06533004 1 6 FLATWASHER,1/2,GR[...]

CNH T6000 Saber Parts Section 5-31 BOOMREST ASSEMBL Y - SABER XB ITEM PART NO. QTY. DESCRIPTION 1 06310035 1 BOOMREST ,BASE 2 06310053 1 BOOMREST ,UPPER 3 06310054 1 BOOMREST ,LOWER 4 06520078 4 WEARP AD,SHOR T ,BOOMREST 5 32686 1 WEARP AD,LONG ,BOOMREST 6 06410587 2 CHANNEL,TIE DOWN 7 21747 4 CAPSCREW , 1/2 x 9,NC 8 22004 12 F L A T W ASHER,1/2,NA[...]

CNH T6000 Saber Parts Section 5-32[...]

P ARTS SECTION COMMON SABER BOOM[...]

[...]

PART NAME INDEX PARTS ORDERING GUIDE ......................................................................................................................................................................... 5 BOOM SWIVEL ASSEMBLY ........................................................................................................................[...]

PART NAME INDEX CLEAN CUTTER HEAD ............................................................................................................................................................................ 67 CLEAN CUTTER ASSEMBLY ......................................................................................................................[...]

PARTS ORDERING GUIDE ©2011 Alamo Group Inc. Parts Section 6-5 COMMON SABER[...]

BOOM SWIVEL ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-6 COMMON SABER[...]

BOOM SWIVEL ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION --- 32742 - SWIVEL W/BUSHINGS,BOOM,SABER 1 32376 1 SWIVEL,BOOM,SABER,W/O BUSHING 2 33705 1 CYLINDER,3X17 1/2,WELDED 3 32381 1 PIN,2 1/2,SWIVEL,SABER 4 33710 1 PIN,CYLINDER,1,SWIVEL,SABER 5 32380 1 PIN,CYL,1,SWIVEL,SABER 6 32372 1 PIN,CYLINDER,STAGE,2ND 7 32378 1 PIN,BOOM TO SWIVEL,SAB[...]

QUICK COUPLERS ©2011 Alamo Group Inc. Parts Section 6-8 COMMON SABER[...]

QUICK COUPLERS Continued... ITEM PART NO. QTY. DESCRIPTION 1 34392 2 ADAPTER,1ORBX1FJX 2 06503028 2 QUICK COUPLER,1”SAE,MALE,FLAT 3 06503027 2 QUICK COUPLER,1”SAE,FEM,FLAT 4 33555 2 ADAPTER,1MORBX1MJIC 5 ------ - PREFORMED TUBES - REFER TO BOOM ARM PARTS 6 ------ - #16 HOSE - REFER TO HYDRAULICS PARTS ©2011 Alamo Group Inc. Parts Section 6-9 C[...]

SABER BOOM ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 32743 1 MAIN BOOM W/BEARING 2 32744 1 SECONDARY BOOM W/BEARING 3 32311 1 MOUNT,SWIVEL HEAD 4 32309 1 MOUNT HEAD PLATE 5 32316 1 LINKAGE,BOOM TO CYLINDER 6 32745 1 LINKAGE W/BEARING,CYLINDER TO SWIVEL ©2011 Alamo Group Inc. Parts Section 6-10 COMMON SABER[...]

SABER BOOM ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 7 32363 1 CYLINDER,5" X 25" 8 32364 1 CYLINDER,4-1/2" X 26-1/2" 9 32365 1 CYLINDER,4" X 15" 10 33542 2 PREFORMED TUBE,1” 11 32627 2 PREFORMED TUBE,3/8” 12 32628 4 PREFORMED TUBE,3/8” 13 32629 4 PREFORMED TUBE,3/8” 14 33541 1 PREFORMED TUBE,1” (RO[...]

SABER MB BOOM ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 06310075 1 BOOM,MB,PRIMARY,SABER 2 06310076 1 BOOM,MB,SECONDARY,SABER 3 21688 5 CAPSCREW,7/16" X 3-1/4,NC 4 32375 3 PIN,1-1/2" X 3-13/16",W/HOLE 5 21677 8 NYLOCK NUT,7/16",NC 6 32363 1 CYLINDER,5" X 25" ©2011 Alamo Group Inc. Parts Section 6-12 COMMON SABER[...]

SABER MB BOOM ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 7 32362 4 BEARING,DX,2" X 2" LONG 8 6T3211 8 GREASE ZERK,1/8" X STR 9 06506042 2 PRFRMD,1,MAIN,SABER MB 10 06506043 4 PRFRMD,2,MAIN,SABER MB 11 33215 7 TUBE CLAMP KIT 12 06506045 1 PRFRMD,4,MAIN,SABER MB (ROTARY RETURN) 13 06506044 1 PRFRMD,3,MAIN,SABER MB (ROTARY PRE[...]

SABER XB BOOM ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 06310031 1 BOOM,LONG,PRIMARY,SABER 2 06310032 1 BOOM,LONG,SECONDARY,SABER 3 21688 5 CAPSCREW,7/16" X 3-1/4",NC 4 32375 3 PIN,1-1/2" X 3-13/16",W/HOLE 5 21677 8 NYLOCK NUT,7/16",NC 6 32363 1 CYLINDER,5" X 25" ©2011 Alamo Group Inc. Parts Section 6-14 COMMON S[...]

SABER XB BOOM ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 7 32362 4 BEARING,DX,2" X 2" LONG 8 6T3211 8 GREASE ZERK,1/8" X STR 9 06506029 2 PRFRMD,1,MAIN,SABER XB 10 06506030 4 PRFRMD,2,MAIN,SABER XB 11 33215 7 TUBE CLAMP KIT 12 06506032 1 PRFRMD,4,MAIN,SABER XB (ROTARY RETURN) 13 06506031 1 PRFRMD,3,MAIN,SABER XB (ROTARY PRE[...]

SABER FLAIL ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 32220 1 BONNET --- 06700014 - CUTTERSHAFT ASSY (ITEMS 2,13,44,45 & 51) 2 06320010 1 CUTTERSHAFT 3 32199 1 GROUND ROLLER 4 32218 1 TAILGATE 5 32302 1 BELT COVER 6 32301 1 GROUND ROLLER MOUNT - RIGHT 7 32300 1 GROUND ROLLER MOUNT - LEFT 8 703976 2 ROLLER BEARING 9 002037 2 ROLLER BEARING SEAL [...]

SABER FLAIL ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 10 02969051 2 PIN 11 32635 2 DEFLECTOR FLAP 12 32636 1 DEFLECTOR FLAP BAR 13 33622 18 CUTTER BLADE 17 02967328 1 BUSHING 18 02967325 1 PULLEY,8 1/2" DIA. 19 32696 1 BUSHING 20 02967327 1 PULLEY,9 3/4" DIA. 21 02967774 1 BELT SET 22 02958198 1 KEY 23 32404 1 MOTOR MOUNT 24 06[...]

SABER DIRECT DRIVE FLAIL ASSY ©2011 Alamo Group Inc. Parts Section 6-18 COMMON SABER[...]

SABER DIRECT DRIVE FLAIL ASSY Continued... ITEM PART NO. QTY. DESCRIPTION --- 06742086 - BONNET,SBF50,DD,ASSY 1 06320112 1 BONNET 2 TF3007A 1 COVER PLATE 3 06410794 1 GUARD 4 06533006 14 FLATWASHER,1/2",GR 9 5 21727 10 NYLOCK NUT,1/2",NC 6 06530404 2 CAPSCREW,SKT/BUT HD,1/2" X 1-1/2",NC 7 06530401 4 CAPSCREW,SKT/BUT HD,1/2"[...]

SABER DIRECT DRIVE ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-20 COMMON SABER[...]

SABER DIRECT DRIVE ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 1 ------ - BONNET *REFER TO BONNET ASSY 2 06506040 1 PREFORMED TUBE 3 TF4852 2 FLANGE KIT 4 06530401 6 CAPSCREW,SKT/BUT HD,1/2" X 1",NC 5 06320126 1 MOTOR GUARD 6 06504003 1 MOTOR,DD 7 06500539 1 HOSE,1" X 82" 8 06530223 4 CAPSCREW,9/16" X 1-3/4",N[...]

50IN SABER ROTARY MOWER ITEM PART NO. QTY. DESCRIPTION 1 33304 - ROTARY,SABER 50",ASSY 2 32914 1 ROTARY,SABER 50",DECK 3 32915 1 SHIELD,50" ROTARY,SABER 4 06504012 1 MOTOR 5 33198 1 MOTOR MOUNTING BRACKET 6 34479 1 SPROCKET,MOTOR 7 34482 1 CHAIN COUPLING 8 34483 1 COVER COUPLING 9 TF4852 2 FLANGE KIT 10 TF1124 1 KEY,WOODRUFF 11 33185[...]

50IN SABER ROTARY MOWER Continued... ITEM PART NO. QTY. DESCRIPTION 12 32952 2 DEFLECTOR FLAP 13 33211 1 RETAINING BAR,FLAP 14 32951 1 HINGE PIN,SHIELD 15 33924 2 ROLLPIN,HINGE PIN 16 32936 2 SKID SHOE 17 34509 1 BAR,KNIVE MOUNTING 18 33203 1 KNIVES,SET OF 2,ROTARY,3/4” 19 34883 2 BOLT,KNIFE 20 6T0822 3 SHIM,MOTOR MOUNT,THIN 21 6T0822A 3 SHIM,MOT[...]

50IN SABER XB ROTARY MOWER ITEM PART NO. QTY. DESCRIPTION --- 06741036 - ROTARY,SABER XB,ASSY 1 06320009 1 ROTARY,SABER XB,DECK 2 06410439 1 COVER,MOTOR MNT 3 22014 2 FLATWASHER,1/4" 4 21530 2 CAPSCREW,1/4" X 1",NC 5 33879 6 CAPSCREW,3/4" X 2-1/4",NF,GR 8 6 33880 6 FLATWASHER,3/4",GR 8,SAE 7 33984 2 PIN,SHIELD,50"[...]

50IN SABER XB ROTARY MOWER Continued... ITEM PART NO. QTY. DESCRIPTION 12 33785 1 CYL,1-1/2 X 8" 13 33778 1 HINGE PIN,50" RTRY 14 6T3017 2 ROLLPIN,3/16" X 1" 15 33754 1 SHIELD,50" RTRY 16 33777 2 SKID SHOE,50" RTRY 17 21993 6 LOCKWASHER,3/4",GR 8 18 6T2413 6 HEX NUT,3/4",NF,GR 8 19 6T1023R 2 KNIFE MTG NUT,1-1[...]

60IN SABER ROTARY MOWER ITEM PART NO. QTY. DESCRIPTION --- 06741072 - ROTARY,SABER 60",ASSY 1 06320169 1 ROTARY,SABER 60",DECK 2 33879 6 CAPSCREW, 3/4" X 2-1/4",NF GR 8 3 33880 6 FLATWASHER,3/4",GR 8,SAE 4 06410439 1 COVER,MOTOR MNT 5 22014 2 FLATWASHER,1/4” 6 21530 2 CAPSCREW,1/4" X 1",NC 7 RD1032 2 PIN,LYNCH,1[...]

60IN SABER ROTARY MOWER Continued... ITEM PART NO. QTY. DESCRIPTION 14 06420139 1 HINGE PIN,60" RTRY 15 06320162 1 SHIELD,60" RTRY 16 6T1024H5 1 SPINDLE 17 21993 6 LOCKWASHER,3/4",GR 8 18 6T2413 6 HEX NUT,3/4",NF,GR 8 19 06400690 1 BAR,BLADE,60” RTRY 20 33764 6 FLATWASHER,5/8",GR 8,SAE 21 6T2259 6 CAPSCREW,5/8" X 1-3[...]

SABER SPINDLE ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-28 COMMON SABER[...]

SABER SPINDLE ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION --- 33219 - SPINDLE ASSY,ROTARY 1 34480 1 TAPERLOCK SPROCKET 2 21530 3 CAPSCREW,1/4” X 1”,NC 3 6T1015 2 BEARING LOCK NUT,THIN 4 22596 1 JAMWASHER 5 6T1014 1 BEARING ADJUST SLEEVE 6 6T1011 2 UPPER SEAL,SMALL 7 6T1012 1 BEARING CONE,SMALL 8 6T1013 1 BEARING CUP,SMALL 9 6T3210 1 GR[...]

SABER XB & 60IN SPINDLE ASSY ©2011 Alamo Group Inc. Parts Section 6-30 COMMON SABER[...]

SABER XB & 60IN SPINDLE ASSY Continued... ITEM PART NO. QTY. DESCRIPTION --- 6T1024H5 - SPINDLE ASSEMBLY 1 6T1031 1 SPROCKET 2 6T1016 1 BEARING LOCK NUT,THICK 3 22596 1 JAM WASHER 4 6T1015 1 BEARING ADJUSTMENT NUT,THIN 5 6T1014 1 BEARING ADJUSTMENT SLEEVE 6 6T1011 1 UPPER SEAL (SET OF 2) 7 6T1012 1 BEARING CONE 8 6T1013 1 BEARING CUP 9 6T1010H [...]

3IN X 17-1/2IN WELDED CYLINDER BREAKDOWN ITEM PART NO. QTY. DESCRIPTION --- 33705 - CYLINDER,WELDED,3" X 17-1/2" 1 34571 1 PISTON ROD ASSY 2 34572 1 BUTT & TUBE ASSY 3 34573 1 PISTON 4 34574 1 GLAND 5 34575 1 LOCK NUT,1"-14 UNS (TORQUE TO 315 FT.LB.) 6 34576 1 SPACER 7 34577 1 CHECK VALVE,KEPNER 8 34578 1 ORIFICE 9 33761 1 SEAL K[...]

4IN X 15IN WELDED CYLINDER BREAKDOWN ITEM PART NO. QTY. DESCRIPTION --- 32365 - CYLINDER,WELDED,4" X 15" 1 34580 1 PISTON ROD ASSY 2 34581 1 BUTT & TUBE ASSY 3 34582 1 PISTON 4 34583 1 GLAND 5 34584 1 LOCK NUT,1-1/4"-12 UNF (TORQUE TO 510 FT.LB.) 9 33757 1 SEAL KIT,PACKING (ITEMS 12 THRU 19) 10 ------ 2 GREASE ZERK 12 ------ 1 O [...]

4-1/2IN X 26-1/2IN WELDED CYLINDER BREAKDOWN ITEM PART NO. QTY. DESCRIPTION --- 32364 - CYLINDER,WELDED,4-1/2" X 26-1/2" 1 34586 1 PISTON ROD ASSY 2 34587 1 BUTT & TUBE ASSY 3 34588 1 PISTON 4 34589 1 GLAND 5 34590 1 LOCK NUT,1-1/4"-12 UNF (TORQUE TO 510 FT.LB.) 9 33758 1 SEAL KIT,PACKING (ITEMS 12 THRU 19) 10 ------ 2 GREASE ZER[...]

5IN X 25IN WELDED CYLINDER BREAKDOWN ITEM PART NO. QTY. DESCRIPTION --- 32363 - CYLINDER,WELDED,5" X 25" 1 34592 1 PISTON ROD ASSY 2 34593 1 BUTT & TUBE ASSY 3 34594 1 PISTON 4 34595 1 GLAND 5 34596 1 LOCK NUT,1-3/4"-12 UNF (TORQUE TO 1800 - 2000 FT.LB.) 7 34597 1 CHECK VALVE,KEPNER 8 34598 1 ORIFICE 9 33759 1 SEAL KIT,PACKING (I[...]

RESERVOIR TANK FILTER ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-36 COMMON SABER[...]

RESERVOIR TANK FILTER ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION ------ 06505044 - FILTER ASSY SAE 10 MICRON 1 28583 4 CAPSCREW,8MM X 25MM(1.25 PITCH) 2 06505045 1 COVER 3 06505046 1 SEAL KIT 4 06505047 1 SPRING 5 06505048 1 BYPASS 6 35259 1 FILTER,10 MIC,RETURN LINE 7 06505049 1 CAN/BODY ©2011 Alamo Group Inc. Parts Section 6-37 COMMON [...]

FRONT HYDRAULIC PUMP ©2011 Alamo Group Inc. Parts Section 6-38 COMMON SABER[...]

FRONT HYDRAULIC PUMP Continued... ITEM PART NO. QTY. DESCRIPTION ------ 23152 - PUMP ASSEMBLY 1-3/4” COMPLETE 1 22765 1 SEAL 2 22766 1 SHAFT END COVER 3 22767 2 CHECK AND END COVER 4 22768 2 BUSHING 5 22769 2 CHANNEL SEAL 6 22770 2 THRUST PLATE 7 22771 1 DRIVE SHAFT AND GEAR SET 1-3/4” 8 22772 2 GASKET SEAL 9 22773 4 DOWEL PINS 10 22774 1 GEAR [...]

50IN FLAIL MOTOR BREAKDOWN ©2011 Alamo Group Inc. Parts Section 6-40 COMMON SABER[...]

50IN FLAIL MOTOR BREAKDOWN Continued... ITEM PART NO. QTY. DESCRIPTION ------ 06504013 - MOTOR ASSEMBLY 350 1 06504039 1 SHAFT END COVER 2 06504040 1 PORT END COVER 3 06504041 1 GEAR HOUSING 4 06504042 1 MATCHED GEAR SET 5 TF4402 1 BALL BEARING 6 06504043 4 CAP SCREW 7 06504044 2 SET SCREW 8 06504028 1 KEY 9 06504045 4 DOWEL PIN 10 ------ 1 NAMEPLA[...]

50IN FLAIL DIRECT DRIVE MOTOR BREAKDOWN ©2011 Alamo Group Inc. Parts Section 6-42 COMMON SABER[...]

50IN FLAIL DIRECT DRIVE MOTOR BREAKDOWN Continued... ITEM PART NO. QTY. DESCRIPTION --- 06504003 - MOTOR ASSEMBLY,DIRECT DRIVE 1 06504039 1 HOUSING,SEC 2 06504040 1 HOUSING,PEC 3 06504041 1 HOUSING,GEAR 4 06504117 1 GEAR,SET 5 06504118 1 SHAFT,CONTINENTAL 6 TF4402 1 BRG,BALL 7 06504043 4 CAPSCREW 8 06504044 2 SCREW,DRIVE 9 06504045 4 PIN,DOWEL 10 0[...]

50IN AND 60IN ROTARY MOTOR BREAKDOWN ©2011 Alamo Group Inc. Parts Section 6-44 COMMON SABER[...]

50IN AND 60IN ROTARY MOTOR BREAKDOWN Continued... ITEM PART NO. QTY. DESCRIPTION 06504011 - MOTOR ASSEMBLY,TRB60 06504012 - MOTOR ASSEMBLY,TRB50 1 22790 1 HOUSING, SEC 2 06504088 1 HOUSING, PEC 3 06504062 1 HOUSING, GEAR,TRB60 ------ 06504089 - HOUSING, GEAR,TRB50 4 06504090 1 SET, GEAR SHAFT 5 06504104 4 CAP SCREW,TRB60 ------ 06504091 - CAP SCREW[...]

COOLER ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-46 COMMON SABER[...]

COOLER ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 1 21530 10 CAPSCREW,1/4 X1 NC 2 21986 10 LOCKWASHER,1/4 3 22014 10 FLATWASHER,1/4 4 35176 10 1/4 U-NUT 5 06370015 1 SCREEN,COOLER,FRNT 6 06380006 1 MNT,COOLER,BUMPER TANK,RH 7 06380007 1 MNT,COOLER,BUMPER TANK,LH 8 06510026 1 COOLER,FRONT MNT 9 21629 4 CAPSCREW,3/8 X 3/4 NC 10 21988 4 LOCK[...]

CABLE (MANUAL) LIFT VALVE, 4 SPOOL - 06502104 ©2011 Alamo Group Inc. Parts Section 6-48 COMMON SABER[...]

CABLE (MANUAL) LIFT VALVE, 4 SPOOL - 06502104 Continued... ITEM PART NO. QTY. DESCRIPTION --- 06502104 - VALVE,MANUAL,4 SPOOL,LOAD SENSE 1 31595 1 INLET END COVER 2 31594 1 END COVER, LOAD SENSE 3 31597 1 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) 4 31597 1 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) 5 31600 1 VALVE SECTION (DOUBLE ACTING, DETEN[...]

CABLE (MANUAL) LIFT VALVE, 5 SPOOL - 06502103 ©2011 Alamo Group Inc. Parts Section 6-50 COMMON SABER[...]

CABLE (MANUAL) LIFT VALVE, 5 SPOOL - 06502103 Continued... ITEM PART NO. QTY. DESCRIPTION --- 06502103 - VALVE,MANUAL,5 SPOOL,LOAD SENSE 1 31595 1 INLET END COVER 2 31594 1 END COVER, LOAD SENSE 3 31597 1 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) 4 31597 1 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) 5 31597 1 VALVE SECTION (DOUBLE ACTING, CENTE[...]

5 SPOOL ELECTRONIC VALVE - 06502096 ITEM PART NO. QTY. DESCRIPTION ------ 06502096 - VLV,5SP,32PVG,SIDE STOW 1 06502074 1 END PLATE 1S 06505013 1 END PLATE SEAL KIT 2 ------ 5 BONNET 2S 06505042 1 BONNET SEAL KIT 2A 42197 1 MAIN BOOM BONNET 2B 42197 1 SECONDARY BOOM BONNET 2C 42197 1 DECK ROLL BONNET 2D 42197 1 BOOM SWIVEL BONNET 2E 42197 1 DECK SH[...]

5 SPOOL ELECTRONIC VALVE - 06502096 Continued... ITEM PART NO. QTY. DESCRIPTION 3 34308 1 INLET SECTION 3S 06505013 1 INLET SECTION SEAL KIT 4 ------ 5 ELECTRONIC ACCUATOR 4A 06502101 1 MAIN BOOM ELECTRONIC ACCUATOR 4B 06502101 1 SECONDARY BOOM ELECTRONIC ACCUATOR 4C 06502100 1 DECK ROLL ELECTRONIC ACCUATOR 4D 06502101 1 BOOM SWIVEL ELECTRONIC ACCU[...]

BRAKE VALVE ASSEMBLY ITEM PART NO. QTY. DESCRIPTION * 06510084 - BRAKE VALVE, ASSY 1 34092 1 BRAKE VALVE, BLANK 2 34094 2 LOGIC ELEMENT 3 34090 1 RELIEF VALVE, 3500 PSI 4 06510095 1 METRI PAK COIL 5 34093 1 CARTRIDGE, 2 POSITION, 3 WAY (WITH NUT & WASHER) 6 34091 1 RELIEF VALVE, 2600 PSI ©2011 Alamo Group Inc. Parts Section 6-54 COMMON SABER[...]

BRAKE VALVE HYDRAULIC SCHEMATIC ©2011 Alamo Group Inc. Parts Section 6-55 COMMON SABER[...]

SOLENOID SWITCH BOX AND WIRING ITEM PART NO. QTY. DESCRIPTION 1 ------ - SWITCH BOX 2 RE37651 1 PLUG,AUX PWR 3 24204 - FUSE HOLDER,IN-LINE (OPTION) 4 6T3965 - FUSE,3AMP (OPTION) 5 6T3934 - TEMPERATURE GAUGE (OPTION) 6 6T3931 - TEMPERATURE SENSOR (OPTION) ©2011 Alamo Group Inc. Parts Section 6-56 COMMON SABER[...]

MANUAL LIFT VALVE SWITCH BOX ITEM PART NO. QTY. DESCRIPTION 1 06514012 1 SWBX,ALUM,BLK,06510100 2 35226 1 SWITCH,MOWER,COLEHERSEE 3 33811 1 SWITCH,MASTER/DECK FLOAT 4 34532 1 SWITCH,TRVL LCK 5 06514014 1 BREAKER,10A,SWBX 6 6T3923 1 INDICTATOR LIGHT,ON,RED 7 34540 1 STRAIN RELIEF,3/4,BLACK,NYLON 8 06550019 1 DECAL,SWTCHBX,BOOM,CG 9 35227 1 RELAY,DP,[...]

MANUAL LIFT VALVE SCHEMATIC ©2011 Alamo Group Inc. Parts Section 6-58 COMMON SABER[...]

ELECTRONIC LIFT VALVE SWITCH BOX ITEM PART NO. QTY. DESCRIPTION 1 06510196 1 SWBX,ASSY 2 33811 2 SWITCH,MASTER/DECK FLOAT 3 33813 1 SWITCH,SFTY SHIELD 4 34532 1 SWITCH,TRVL LCK 5 34540 1 STRAIN RELIEF,3/4",BLACK,NYLON 6 6T3923 1 INDICTATOR LIGHT,ON,RED 7 06514006 1 BREAKER,15A,SWBX 8 06550044 1 DECAL,SWBX,06510047 9 35226 1 SWITCH,MOWER,COLEHE[...]

ELECTRONIC LIFT VALVE SCHEMATIC ©2011 Alamo Group Inc. Parts Section 6-60 COMMON SABER[...]

LEFT HAND JOYSTICK SWITCHBOX SCHEMATIC ©2011 Alamo Group Inc. Parts Section 6-61 COMMON SABER[...]

TROUBLESHOOTING ©2011 Alamo Group Inc. Parts Section 6-62 COMMON SABER[...]

TROUBLESHOOTING - CONTINUED ©2011 Alamo Group Inc. Parts Section 6-63 COMMON SABER[...]

HYDRAULIC TROUBLESHOOTING GUIDE ©2011 Alamo Group Inc. Parts Section 6-64 COMMON SABER[...]

ELECTRICAL TROUBLESHOOTING GUIDE ©2011 Alamo Group Inc. Parts Section 6-65 COMMON SABER[...]

NOTES 1 ©2011 Alamo Group Inc. Parts Section 6-66 COMMON SABER[...]

CLEAN CUTTER HEAD ©2011 Alamo Group Inc. Parts Section 6-67 COMMON SABER[...]

CLEAN CUTTER ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-68 COMMON SABER[...]

CLEAN CUTTER OPERATION ©2011 Alamo Group Inc. Parts Section 6-69 COMMON SABER[...]

CLEAN CUTTER OPERATION - CONTINUED ©2011 Alamo Group Inc. Parts Section 6-70 COMMON SABER[...]

CLEAN CUTTER MAINTENANCE ©2011 Alamo Group Inc. Parts Section 6-71 COMMON SABER[...]

CLEAN CUTTER BLADE AND TEETH PARTS ITEM PART NO. QTY. DESCRIPTION 1 06420025 1 ADAPTER,SAW,SABER,RNFRCD 2 06520224 1 BLADE, 48” SAW WITH TEETH 3 06420038 1 COLLAR,SAW,SABER 4 33380 6 FLATWASHER,3/4",GR8,SAE 5 06530210 6 CAPSCREW,5/8" X 3-3/4",NF,GR 8 6 06520225 30 TOOTH WITH RIVET, SAW BLADE 7 34703 30 TOOTH RIVET, SAW BLADE --- 34[...]

CARBIDE TIP REPLACEMENT ©2011 Alamo Group Inc. Parts Section 6-73 COMMON SABER[...]

NOTES 2 ©2011 Alamo Group Inc. Parts Section 6-74 COMMON SABER[...]

FIRE SUPRESSION SYSTEM ©2011 Alamo Group Inc. Parts Section 6-75 COMMON SABER[...]

FIRE SUPRESSION SYSTEM PARTS ©2011 Alamo Group Inc. Parts Section 6-76 COMMON SABER[...]

FIRE SUPRESSION SYSTEM PARTS Continued... ITEM PART NO. QTY. DESCRIPTION 1 06520357 1 TANK,FIRE SUPRESS SYS,RAILKUT 2 06520358 1 MNT,TANK,FIRE KIT,RAILKUT 3 06520359 1 PUMP,FIRE SUPRESS SYS,RAILKUT 4 6T2181 4 CAPSCREW,SKT HD,10/24 X 3/4 5 24890 4 HEX NUT,10-24 NYLOCK 6 06520360 1 HOSE REEL,FIRE KIT,RAILKUT 7 21630 4 CAPSCREW, 3/8 X 1,NC 8 21627 8 N[...]

FIRE SUPRESSION SYSTEM ELECTRICAL SCHEMATIC ©2011 Alamo Group Inc. Parts Section 6-78 COMMON SABER[...]

WETCUT ©2011 Alamo Group Inc. Parts Section 6-79 COMMON SABER[...]

WETCUT 50 GALLON TANK MOUNT ITEM PART NO. QTY. DESCRIPTION 1 06370128 1 MNT,3PNT,UNI 2 06370136 1 MNT,TANK,50GAL,WETCUT 4 06520342 1 TANK,50GA.,WETCUT 7 RD1032 3 PIN,LYNCH 1/4" X 2" 8 TB1036 1 PIN,SEC BOOM SWIV 1X4-11/16" 9 06520343 4 ANCHOR,STRAP,WETCUT 10 06520344 4 BOLT,STRAP,TANK,WETCUT 11 06520345 2 STRAP,TANK,WETCUT ©2011 Alam[...]

WETCUT 100 OR 150 GALLON TANK MOUNT ITEM PART NO. QTY. DESCRIPTION 1 06370128 1 MNT,3PNT,UNI 2 06370138 1 MNT,TANK,100GAL,WETCUT ------ 06370139 - MNT,TANK,150GAL,WETCUT 4 06520372 1 TANK,100GA.,WETCUT ------ 06520373 - TANK,150GA.,WETCUT 5 21527 2 HEX NUT,NYLOCK,1/4" NC 6 21530 2 CAPSCREW,1/4" X 1" NC 7 RD1032 3 PIN,LYNCH 1/4" [...]

WETCUT TANK PLUMBING ©2011 Alamo Group Inc. Parts Section 6-82 COMMON SABER[...]

WETCUT TANK PLUMBING Continued... ITEM PART NO. QTY. DESCRIPTION 1 06370128 1 MNT,3PNT,UNI 2 06520336 1 CNTRLR,SENSOR,06520333 3 06520341 1 PUMP,WETCUT 4 06520346 1 FITTING,BULKHEAD,WETCUT 5 06520347 1 FITTING,ELBOW,WETCUT 6 06520348 1 VLV,BALL,WETCUT 7 06520349 6 FITTING,BARB,HOSE,WETCUT 8 06520352 4 FITTING,NIPPLE,1/2X3/8,WETCUT 9 06520353 1 FITT[...]

WETCUT SPRAYER HEAD ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-84 COMMON SABER[...]

WETCUT SPRAYER HEAD ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 1 06370105 1 HOOD,SPRAYER 2 06370106 1 HINGE,LH,SPRAYER 3 06370107 1 HINGE,RH,SPRAYER 4 06370108 1 HINGE,CNTR,SPRAYER 5 06410668 1 GUARD,SPRAYER,WETCUT 6 06410753 1 MNT,RH,WET CUT 7 06410754 1 MNT,LH,WET CUT 8 06410796 1 GUARD,HOSE,WETCUT 9 06420069 3 PIN,HINGE,WET CUT 10 0649[...]

WETCUT CABLES ©2011 Alamo Group Inc. Parts Section 6-86 COMMON SABER[...]

W ARRANTY SECTION Warranty Section 7-1[...]

.[...]

W ARRANTY INFORMA TION T iger Corporation, 3301 N. Louise, Sioux Falls, South Dakota, warrant s to the original Retail Customer , the new T iger equipment is free of defects in material and workmanship. Any part of equipment that in T iger ’s judgement, show evidence of such defects will be repaired or replaced without charge, provided that the f[...]

ONE LAST WORD This manual cannot possibly cover all of the potentially hazardous situations you will encounter . By being familiar with the safety rules, operating and maintenance instructions in this manual you can help prevent accidents. The objective of this manual is to help make you a better operator . Remember , SAFETY IS YOU! Y our safety an[...]

T O THE OWNER / OPERA TOR / DEALER T o keep your implement running ef ficiently and safely , read your manual thoroughly and follow these directions and the Safety Messages in this manual and on the machine. The table of contents clearly identifies each section where you can easily find the information you need. The Occupational Safety and Health A[...]

Printed in USA © T iger Corporation[...]