Toshiba A500D/PRO A500DPRO A500D manuale d’uso

Toshiba Personal Computer Satellite Maintenance Manual TOSHIBA CORPORATION [CONFIDENTIAL][...]

ii [CONFIDENTIAL] Satellite A500D/Pro A 500D Series Maintenance Manual Copyright © 2009 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the inform ation contained herein. Tos[...]

Satellite A500D/Pro A500D Series Maintenance Manual [CONFIDENTIAL] iii Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Satellite, referred to as the Satellite Series in this m anual. The procedures described in this manual are intended to help service technicians isolate faulty[...]

iv [CONFIDENTIAL] Satellite A500D/Pro A 500D Series Maintenance Manual The manual is divided into the following parts: Chapter 1 Hardware Overview describes the Satellite Series system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform te[...]

Satellite A500D/Pro A500D Series Maintenance Manual [CONFIDENTIAL] v Some operations require you to simultaneously use two or m ore keys. We identify such operations by the key top symbols separated by a plus (+) sign. For example, Ctrl + Pause (Break) m eans you must hold down Ctrl and at the same tim e press Pause (Break) . If three keys are used[...]

vi [CONFIDENTIAL] Satellite A500D/Pro A 500D Series Maintenance Manual Table of Contents Chapter 1 Hardware Overview 1.1 Features ................................................................................................................... ..........1-1 1.2 2.5-inch HDD .........................................................................[...]

Satellite A500D/Pro A500D Series Maintenance Manual [CONFIDENTIAL] vii 2.16 7 in 1 card Troubleshooting ............................................................................................... 44 2.17 HDD Troubleshooting ....................................................................................................... .. 46 2.18 CRT fai[...]

viii [CONFIDENTIAL] Satellite A500D/Pro A500D Series Maintenance Manual 3.15 BUTTON Test……..…………...………….…….……… . ……..…………...……............24 3.16 1st HDDTest ……………………………....……………. . ……………....….…………...26 3.17 RDMI Test ………………...…………?[...]

Satellite A500D/Pro A500D Series Maintenance Manual [CONFIDENTIAL] ix Installing the ODD Bay Module ...................................................................................... 4-20 Disassembling the ODD Drive ........................................................................................ 4-20 Assembling the ODD Drive ...........[...]

x [CONFIDENTIAL] Satellite A500D/Pro A 500D Series Maintenance Manual Removing the Motherboard ..............................................................................................4-36 Installing the Motherboard ................................................................................................4-38 4.18 VGA Board and VGA Therm[...]

Satellite A500D/Pro A500D Series Maintenance Manual [CONFIDENTIAL] xi Figures Figure 4.1 Removing the Battery Pack .................................................................................... 4-8 Figure 4.2 Removing the HDD door ..................................................................................... 4-10 Figure 4.3 Removing th[...]

xii [CONFIDENTIAL] Satellite A500D/Pro A 500D Series Maintenance Manual Figure 4.30 Align the DP CONN, S/PDIF CONN, Audio CONN and RJ45 CONN...............4-38 Figure 4.31 Installing the DC-in jack .......................................................................................4- 39 Figure 4.32 Removing the VGA Board. .......................[...]

Satellite A500D/Pro A500D Series Maintenance Manual [CONFIDENTIAL] xiii (low-end model) ................................................................................................... 4-59 Figure 4.59 Removing the LCD Hinge Assembly................................................................... 4-60 Figure 4.60 Removing the LVDS cable from [...]

Chapter 1 Hardware Overview[...]

1 Hardware Overview Satellite A500D Main tenance Manual 1-ii Chapter 1 Contents 1.1 Features .................................................................................................................. 1-1 1.2 2.5-inch HDD ....................................................................................................... 1-11 1.3 DVD Supe[...]

1 Hardware Overview Satellite A 50 0D Maintenance Manual 1-iii Figures Figure 1-1A ID Parts Description Placement Part A.......................................................... 1-7 Figure 1-2 SATA HDD ................................................................................................. 1-11 Figure 1-3 DVD Super Multi Drive ...........[...]

[...]

Error! Style not defined. Error! Style not defined. 1 Hardware Overview Satellite A500D Maintenance Manual 1-1 1.1 Features The Toshiba Satellite A500/A500D is a full-size PC notebook based on a Dual Core Processor, providing high-speed processing capabilities and advanced features. The computer em ploys a lithium ion battery that allows it to be b[...]

1 Hardware Overview Error! Style not defined. Error! Style not defined. Satellite A500D Maintenance Manual 1-2  ODD (BTO)  12.7mm height DVD Super Multi drive supporting ±R Double Layer  12.7mm height DVD Super Multi drive supporting ±R Double Layer w/ Labelflash  Display (BTO) The LCD displays available come with one of the following[...]

Error! Style not defined. Error! Style not defined. 1 Hardware Overview Satellite A500D Maintenance Manual 1-3  Universal Serial Bus (USB) Ports The computer has three USB 2.0 ports. It is supported to daisy-chain a maxim um of 127 USB devices. The serial data transfer rate is 480 Mbps or 12 Mbps and 1.5 Mbps. These ports support PnP installatio[...]

1 Hardware Overview Error! Style not defined. Error! Style not defined. Satellite A500D Maintenance Manual 1-4  Headphones/S/PDIF/Line out Jack This jack connects digital speakers or stereo headphones (16 ohm minim um). When connected to digital speakers or headphones, the internal speaker is automatically disabled. This jack can also be used as[...]

Error! Style not defined. Error! Style not defined. 1 Hardware Overview Satellite A500D Maintenance Manual 1-5  Felica (BTO) Imbedded Felica module writes and reads data to and from contact less Felica IC cards. Having no need for physical contact with the card, the Reader/Writer is imm une to performance deterioration caused by wear and contami[...]

1 Hardware Overview Error! Style not defined. Error! Style not defined. Satellite A500D Maintenance Manual 1-6  DislpayPort (BTO) A 20-pin DisplayPort is installed on some co mputers to send and receive HD and SD video and audio signals (similar to HDMI). Support Display port1.0 and 1.1 protocols for dual mode adapter.  TV Tuner (BTO) Some mo[...]

Error! Style not defined. Error! Style not defined. 1 Hardware Overview  Figure 1-1A shows the computer and its system unit configuration. Figure 1-1A ID Parts Description Placement Part A Satellite A500D Maintenance Manual 1-7[...]

1 Hardware Overview Error! Style not defined. Error! Style not defined. Satellite A500D Maintenance Manual 1-8[...]

Error! Style not defined. Error! Style not defined. 1 Hardware Overview Satellite A500D Maintenance Manual 1-9 The system unit of the computer consists of the following com ponents:  Processor (BTO) The computer is equipped with one of the following AMD ® processors.  AMD Turion TM 64 X2 Dual-Core Processor  AMD Athlon TM X2 Dual-Core Pro[...]

1 Hardware Overview Error! Style not defined. Error! Style not defined. Satellite A500D Maintenance Manual 1-10  Graphics Controller  AMD RS780MN/RS780MC as integrated graphics solution  Following External Graphic solution with AMD M780G/M770  ATI Mobility Radeon TM HD 3470 (512MB)  ATI Mobility Radeon TM HD 3650 (1GB)  HDMI 1.3-C[...]

Error! Style not defined. Error! Style not defined. 1 Hardware Overview 1.2 2.5-inch HDD The computer contains an extremely low-prof ile and lightweight, high-performance HDD. The HDD incorporates 9.5 mm / 12.5 m m height magnetic disk and m ini-Winchester type magnetic heads. The HDD interface conforms to Serial ATA. Storage capacities supported a[...]

1 Hardware Overview Error! Style not defined. Error! Style not defined. Satellite A500D Maintenance Manual 1-12 Table 1-1 HDD Specifications Item Specifications Capacity (GB ) 120GB 160 GB 200 250 GB Rotational Speed (RPM) 5400 or 7200 RPM 5400 or 7200 RPM 7200 RPM 5400 RPM Height 9.5 mm 9.5 mm 9.5 mm 9.5 mm User Data Sectors 234,441,648 312,581,80[...]

Error! Style not defined. Error! Style not defined. 1 Hardware Overview 1.3 DVD Super Multi (+-R Double Layer) The DVD Super Multi drive accepts 12-cm (4.72-inch) and 8-cm (3.15-inch) discs. At m aximum, the drive can play back a DVD at 8x speed, read CD-ROM at 24x speed, and write CD-R at 24x speed, CD-RW at 6x speed, CD-RW at 16x speed, DVD-R at [...]

1 Hardware Overview Error! Style not defined. Error! Style not defined. Satellite A500D Maintenance Manual 1-14 1.4 Power Supply The power supply unit provides constant voltage (19V) for the system board and performs the following functions: 1. Power input monitor  Checks whether the AC adapter (DC power supply) is connected to the computer. [...]

Error! Style not defined. Error! Style not defined. 1 Hardware Overview Satellite A500D Maintenance Manual 1-15 6. Output monitor  Monitors the voltage output to the system block (load/logic circuit side).  Monitors the voltage, over-voltage, input/output current of the battery pack.  Monitors the internal temperature of the battery pack. [...]

1 Hardware Overview Error! Style not defined. Error! Style not defined. Satellite A500D Maintenance Manual 1-16 1.5 Batteries The computer has the following two types of batteries:  Main Battery Pack  Real Time Clock (RTC) Battery 1.5.1 Main Battery The main battery pack serves as the computer' s main power source when the AC adapter is [...]

Error! Style not defined. Error! Style not defined. 1 Hardware Overview Satellite A500D Maintenance Manual 1-17 NOTE: The time required for normal charge depends on the power consumption by the system. Using a fluorescent lamp and frequently accessing the disk consumes more power and lengthen the charge time. Any of the following can stop battery c[...]

Chapter 2 Troubleshooting Procedures[...]

[...]

2 Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 1 Chapter 2 Contents 2.1 ...................................................................................... Troubleshooting Introduction 3 2.2 Troubleshooting Flowchart ……………………………………………………[...]

2 Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 2 Figures Figure 2-1 Troubleshooting flowchart (1/2) ....................................................................... 5 Figure 2-1 Troubleshooting flowchart (2/2) ...............................................................[...]

2 Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 3 Tables Table 2-1 Battery LED ........................................................................................................10 Table 2-2 DC-IN LED ...........................................................................[...]

2 Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 4 12. Headphones 13. USB test module and USB cable 14. Music CD 15. MIC module and MIC line 16. SPDIF line 17. Finger print module 18. TV tuner signal generator 19. FM tuner signal generator 20. E-SATA HDD 21. Felica card 22. UWB sig[...]

2 Troubleshooting Procedures STA R T C onne ct t he A C ada pt er t o t he D C - I N sock et I s t h e DC- I N L ED o n ? Is th e B a tte ry L E D o n ? T u rn th e P o w e r sw itch o n Is th e P o w e r O n L E D o n ? I s t he " T os hi ba" l ogo m es s age di s pl ay? If the "pa ssw o rd" m essa ge di s pl ays , t ype t he p[...]

2 Troubleshooting Procedures A Does typed characters appear correctly? Insert USB memo ry disk, Then run the diagnost ics test program . Is the diagnostics test loaded? Allow each test to perform automatically Is an error detected by any of the diagno stic s te st s? System i s normal End Ye s Ye s Ye s No Perform the Keyboard Troubleshooti ng proc[...]

2 Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 7 If the diagnostics program cannot detect an erro r, the problem may be intermittent. The test program should be executed several times to isol ate the problem. W hen a problem has been located, perform the appropriate trou bleshoot[...]

2 Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 8 Other problems that are not covered by the di agnostics program may be discovered by a user. 1. If an error is detected when using an ex ternal USB device, perform the External USB Devices Troubleshooting pr ocedures in Section 2.5[...]

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting ST ART Are the D C - IN and B a tte ry L E D s lit? Can you tur n the com puter o n? A r e th e inte rn a l p o w er connecti ons secure? END Check P ower Supp l y Sta tus (Procedure 1) No Ye s Chec k powe r s uppl y connect ions (Procedure 3) R un di agnost i c program (Procedure 4) Ye [...]

2 Troubleshooting Procedures The power supply controls many functions and components. To determ ine if the power supply is functioning properly, star t with Procedure 1 and continue with the other Procedures as instructed. The flowchart in Figure 2-2 give s a summary of the proc ess. The procedures described in this section are: Procedure 1: Power [...]

2 Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 11 Table 2-2 DC-IN LED AC-IN LED Power supply status Solid on AC power exists (LED is solid White). Off No AC power exists. To check the power supply status, install a ba ttery pack and connect an A C adaptor to the DC-IN port on the[...]

2 Troubleshooting Procedures Procedure 3 Pow er supply connection check The power supply wiring diagram is shown below: AC adaptor Sys t em boar d B a tter y A C adaptor cord AC p o we r c o r d Any of the connectors may be disconnected. Perform Check 1. Check 1 Disconnect the AC power cord from wall outlet. Check the power cable for breaks. If the[...]

2 Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 13 Procedure 4 Diagnostic check The power supply may not charge the battery pack. Perform the following procedures: 1. Reinstall the battery pack. 2. Attach the AC adaptor and turn on the power . If you cannot turn on the power, go t[...]

2 Troubleshooting Procedures 2.4 Display Troubleshooting Per f or m ext er nal di s pl ay che ck ( P r oce dur e 1) STA R T D o es t h e ext ernal di s pl ay f unct i on ok? Per f or m di agnos t i c c hec k (Proced ure 2) No Wa s a d i s p l a y pr obl em det e ct e d? Per f or m connec t or and r ep l acem en t ch eck (Proced ure 3) R eplace syst[...]

2 Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 15 This section describes how to determ ine if th e computer’s display is functioning properly. The process is outlined in Figure 2-3. Start wi th Procedure 1 and continue with the other procedures as instructed. Procedure 1: Exter[...]

2 Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 16 Procedure 3 Connector and replacement check The FL inverter board, LCD module, and system board are connected to the display circuits. Any of these components may be damaged. Refer to Chapter 4, Replacement Procedures, for instruc[...]

2 Troubleshooting Procedures 2.5 Keyboar d Troubleshooting Per f or m ext er nal keyboa r d che ck ( Pr oc e dur e 1) STA R T D o es t he ex t er n al keyboa r d f unct i on ok? Per f or m di agnos t i c c he ck ( Pr oc edur e 2) W as a keyboa r d pr obl em det ec t ed? P e rfo rm c o n n e c t o r a n d r ep l acem en t ch eck ( Pr oc edur e 3) R [...]

2 Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 18 Procedure 1 External keyboard check Connect a USB keyboard to one of the computer’s USB ports, and then boot the computer. The computer automatically de tects the external keyboard. If the external keyboard works correctly, the [...]

2 Troubleshooting Procedures 2.6 External USB Devices Troubleshooting R epl ace syst em b oar d (P ro ce du re 2) EN D O rig in a l U S B devi ce i s f aul t y P erfo rm ex tern al d ev ice an d conn ec t i on chec k (P ro ce du re 1) STA R T D o e s th e d e v ice fu n c tio n w hen connect ed t o a d i ffere n t U S B p o rt ? D o es an al t erna[...]

2 Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 20 To determine if the computer’s external US B devices are functioning properly, perform the following procedures. Figure 2-5 outlines the proce ss. Start with Procedure 1 and continue as instructed. Procedure 1: External device a[...]

2 Troubleshooting Procedures 2.7 TV-Tuner Failure Troubleshooting P erfo rm T V T u n er C a b l e con nect ion ch eck ( Pr oce dur e 1) STA R T D oe s repl acem en t T V T uner ca bl e f unct i on pr ope r l y? Per for m T V Tuner SG se t t i ng check ( Pr oce dur e 2) A Ye s R ep l ace T V Tuner cabl e No TV T une r f unct i oni ng ok? No U se t [...]

2 Troubleshooting Procedures A R eplace syst em b oard EN D D o es r ep l acem en t T V T uner A nt enna f unct i on pr oper l y? Ye s R epl ace T V T une r A nt enna D o es r ep l acem en t T V T uner M o dul e f unct i on pr oper l y? Ye s R ep l ace T V T une r M odul e Per f orm TV T une r M odul e conne ct i on c hec k ( P r o cedure 4) No Sat[...]

2 Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 23 To determine if the computer’s TV Tuner por t is functioning properl y, perform the following procedures. Figure 2-6 outlines the p rocess. Start with Procedure 1 and co ntinue as instructed. Procedure 1: TV Tuner cable connecti[...]

2 Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 24 replacement Antenna does not work the TV tuner Module may be damaged. Go to Procedure 4. Procedure 4 TV Tuner Module Connection check The TV Tuner Module connect may be faulty. Perform Check 1: Check 1 Check the TV Tuner Module is[...]

2 Troubleshooting Procedures 2.8 Touch Pad Troubleshooting START END To uchPad connecti o n check (Procedure 1) TouchPad replacemen t check (Procedure 2) Replace sy stem board Figure 2-7 Touchpad troubleshooting process Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 25[...]

2 Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 26 To determine if the computer’s built-in T ouchPad is functioning properly, perform the following procedures. Figure 2-7 outlines the proce ss. Start with Procedure 1 and continue as instructed. Procedure 1: TouchPad connection c[...]

2 Troubleshooting Procedures 2.9 Speaker Troubleshooting ST A RT D o al l so urce s ha ve s am e pr obl em ? EN D Per f or m e ar phone t es t ( P r o cedure 2) Do e a r p h o n e s fu n ctio n c o rr e c tly? P er f o r m co nnect i o n check ( P r o cedure 3) P er f o r m r ep l acem ent check ( P r o cedure 4) Per f or m a udi o so ur ce t es t [...]

2 Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 28 To determine if the computer’s built-in sp eakers are function ing pr operly, perform the following procedures. Figure 2-8 outlines the pro cess. First adjust the speaker volume to an appropriate level. Start with Proced ure 1 a[...]

2 Troubleshooting Procedures 2.10 Optical Drive Troubleshooting ST ART Audio CD f unct ions ok? END Perform softwa re check (Procedure 3) Per form d iagnostic test (Procedure 4) Pe rform connection and replacemen t check (Procedure 5) Perf orm au dio C D che ck (Procedure 1) Per for m dr iv e- cleaning check (Proced ure 2) No Yes Replace s ys tem b[...]

2 Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 30 P200D Series Maintenance Manual module bays can accommodate the following optical drives: DVD SuperMulti supporting +-R Double Rayer Figure 2-9 outlines the process. Pe rform the steps below starting with Procedure 1 and continue [...]

2 Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 31 Procedure 4 Connectio n check and replacement check The optical drive connects to the system board. The drive may be disconnected, or the drive or system board may be dam aged. Disassemble the computer following the steps describe[...]

2Troubleshooting Procedures 2.11 Mode m Troubleshooting ST ART Com puter un able to detect t eleph one si gnal ? END Perform connection check (Procedure 2) Perform replacemen t check (Procedure 3) Perform telephone line connection check (Procedure 1) Check / replac e teleph one line and connect ions Yes Replace sy stem board No Figure 2-10 Modem tr[...]

2Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 33 This section describes how to determine if the computer' s modem is functioning properly. Figure 2-10 outlines the process. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required[...]

2Troubleshooting Procedures 2.12 Express card Troubleshooting START D o er r or s oc cur dur i ng E x press c ard test ? Per f or m E xpr e s s car d s ocket r eplacem en t check ( Pr oce dur e 2) R epl ace syst em b oar d END Expre ss car d uni t is n o t fa u lty . Per f or m E xpr e s s ca r d t es t ( Pr oce dur e 1) No Ye s Figure 2-11 Express[...]

2Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 35 This section describes how to determ ine if th e Express card player is functioning properly. The process is summarized in Figure 2-11. Perf orm the steps below starting with Procedure 1 and continuing with the othe r procedures as[...]

2Troubleshooting Procedures 2.13 Wireless LAN Troubleshooting STAR T P erfo rm d ia gn os tic te st (Proced ure 1) W as a w ireless LAN p roblem delected? P erform conn ector and replacem en t check (Proced ure 2) Re pl ac e wir e l es s L AN a nt e nn a /u ni t R eplace system bo ard END Ye s W ir eless LA N sy stem is n o t fau lty. C o ntin u e [...]

2Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 37 computer’s wireless LAN system is functioni ng properly, perform the following procedures. Figure 2-12 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Diagnostic tes[...]

2Troubleshooting Procedures 2.14 Camera Troubleshooting Figure 2-13 Camera troubleshooting process The Camera board or system board may be the reason of a Cam era fault. Either of these two components may be damaged. To determine if the com puter’s Camera is functioning Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintena[...]

2Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 39 properly, perform the following procedures. Fi gure 2-13 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Windows Application test Procedure 2: Connector and replacemen[...]

2Troubleshooting Procedures 2.15 Bluetoot h Troubleshooting ST A R T Pr ef o r m d i ag n o s t i c t es t ( P ro c e d u re 1 ) W a s a B l ue t oot h pr ob l e m de t e c t ? B l ue t oot h i s not f a ul t y . C o n t i n u e t r o u b l es h o o t i n g - r ef er to F i g u r e 2 . 1 R ep l ace s y s t em b o ar d P e r f or m c onne c t or a n[...]

2Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 41 The Bluetooth antenna wire, Bluetooth module or system board may be the reason of a Bluetooth fault. Any of these components may be dam aged. To determine if the computer’s Bluetooth is functioning properl y, perform the followin[...]

2Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 42 Check 4 The system board may be dam aged. Replace it with a new one following the instructions in Chapter 4.[...]

2Troubleshooting Procedures 2.16 Bridge Media Sl ot Troubleshooting START Do errors occur during Bridge Media Slot test? Perform Bridge Media Slot replacement check (Procedure 2) Replace system board END Bridge Media Slot unit is not faulty. Perform Bridge Me dia S lot test (Procedure 1) No Yes Figure 2-15 Bridge Media Sl ot troubleshooting process[...]

2Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 44 Procedure 1: Bridge Media Slot test Procedure 2: Bridge Media Slot replacement check Procedure 1 Bridge Media Slot test The Bridge Media Slot test PL S Use windows application to check device can work fine or not. Ensure the card i[...]

2Troubleshooting Procedures 2.17 HDD/ SSD Troubleshooting Figure 2-16 HDD/SDD troubleshooting process Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 45[...]

2Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 46 The HDD/SSD or system board may be the reason of a HDD/SSD fault. Either of these two components may be damaged. To determine if the computer’s HDD/SDD is functioning properly, perform the following procedures. Fi gure 2-16 outli[...]

2Troubleshooting Procedures 2.18 CRT Troubleshooting P e rfo rm C R T c o n n e c ti o n ch eck (P ro c e d u re 1 ) ST A R T D o es r ep l acem en t C R T cab l e f unc t i on pr op e r l y? P er f o r m C R T s et ch eck (P ro c e d u re 2 ) R ep l ace syst em b o ar d EN D No Re p l a c e CRT cab l e No C R T f u nc t i oni ng ok? NO U se di f f[...]

2Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 48 Procedure 1: CRT connection check Procedure 2: CRT set check Procedure 1 CRT conn ection check The CRT cable may be damaged or the connect ions m ay be loose. Use windows application to check device can work fine or not. Perform Ch[...]

2Troubleshooting Procedures 2.19 HDMI Troubleshooting P e rfo rm H D M I c o n n ec ti o n che ck ( Pr ocedur e 1) STA R T D oes r epl acem en t H D M I cabl e f unct i on pr oper l y? P e rfo rm H D M I s e t c h e ck ( Pr ocedur e 2) R ep l ace syst em b oard EN D No R epl ace H D M I cab l e No H D M I f unct i oni ng ok? No U se di f f er ent H[...]

2Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 50 Procedure 1: HDMI connection check Procedure 2: HDMI set check Procedure 1 HDMI connection check The HDMI cable may be damaged or the connec tions m ay be loose. Use windows application to check device can work fine or not. Perform[...]

2Troubleshooting Procedures 2.20 Displa y Port Troubleshooting P e rfo rm D isp lay P o rt c o n n ec t io n check ( P r ocedur e 1) STA R T D o es repl acem ent D i spl ay Por t c ab l e f unct i on pr oper l y? P e rfo rm D isp l a y P o rt se t c h e c k ( P r ocedur e 2) R epl ace syst em b oar d EN D No R epl ace D i spl ay P or t cabl e No D [...]

2Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 52 Procedure 1: Display Port connection check Procedure 2: Display Port set check Procedure 1 Display Port connection check The Display port cable may be damaged or the connections may be loose. Use windows application to check device[...]

2Troubleshooting Procedures 2.21 SPDIF troubleshooting Figure 2-20 SPDIF troubleshooting process The system board may be the reason of a SPDIF fault. The connector of system board may be damaged. To determine if the com puter’s SPDIF is functioning properly, perform the Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintena[...]

2Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 54 following procedures. Figure 2-20 outlines the p rocess. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: windows application test Procedure 2: Connector and replacement check Procedure 1 wi[...]

2Troubleshooting Procedures 2.22 MIC Troubleshooting Figure 2.21. MIC troubleshooting process The MIC line or system board may be the re ason of a MIC fault. Either of these two components may be damaged. To determine if the computer’s MIC is functioning properly, Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Ma[...]

2Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 56 perform the following pr ocedures. Figure 2-21 outlines the process. Sta rt with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Windows Application test Procedure 2: Connector and replacement check P[...]

2Troubleshooting Procedures 2.23 Finger printer troubleshooting Figure 2-22 Finger printer troubleshooting process The Finger printer board or system board may be the reason of a finger prin ter fault. Either of these two components may be damaged. To determine if the com puter’s Finger printer is Satellite A500D/Satellite A505D/Satellite A507D/S[...]

2Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 58 functioning properly, perform the following proc edures. Figure 2-22 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: windows application test Procedure 2: Connector an[...]

2Troubleshooting Procedures 2.24 FM tuner Failure Troubleshooting Per f or m F M T uner A nt e nna conne ct i on chec k ( P r o cedu r e 1 ) STA R T D o es r ep l acem en t F M T un er A nt enna f unct i on pr ope r l y? P e r fo rm F M T u n e r S G s e ttin g che ck ( P r o cedu r e 2 ) A Ye s R epl ace F M T une r A nt enna No FM T uner f unct i[...]

2Troubleshooting Procedures A R ep l ace syst em b oar d EN D D o es r ep l acem en t F M T u n er B oa r d f unct i on pr oper l y? Ye s R ep l ac e F M t uner boar d No To determine if the computer’s FM tuner por t is functioning properly, perform the following procedures. Figure 2-23 outlines the process. Start with Procedure 1 and continue as[...]

2Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 61 Check 1 Make sure FM Tuner Antenna is firmly plugged into FM Tuner port of the computer. If the Antenna is connected correctly, go to Check 2. Check 2 Try connecting a different FM Tuner An tenna to the computer. If the replacement[...]

2Troubleshooting Procedures 2.25 E-SATA Troubleshooting STA RT Perform E -SA TA d ev ice ch eck (Pro c ed ure 1 ) Is E-SATA tr ansmiss ion o k? Perfo rm dia g n ostic c h e ck (Pro c ed ure 2 ) W as an E -SA TA p rob lem detected? Perform co nn ection an d replacem ent check (Pro c ed ure 3 ) Rep lace sy stem bo ard END Yes Yes E-SATA port and tran[...]

2Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 63 Procedure 3: Connection and replacement check Procedure 1 E-SATA d evice check Connect an E-SATA device to the computer’s E-SATA port, then boot the computer for Windows Vista. The computer should automatically detect the E-SATA [...]

2Troubleshooting Procedures 2.26 Felica Troubleshooting START END Felica connection check (Procedur e 1) Felica replacement check (Procedur e 2) Replace system board Figure 2-25 Felica troubleshooting process Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 64[...]

2Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 65 To determine if the computer’s built-in Feli ca is functioning properly, perform the following procedures. Figure 2-25 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: Felica connection check [...]

2Troubleshooting Procedures 2.27 UWB Troubleshooting P e r f o r m UW B An t e n n a conne ct i on chec k ( P r o cedu r e 1 ) STA R T D o es r ep l acem ent U W B A nt enna f unct i on pr oper l y? P e rfo rm U W B S G s e ttin g che ck ( P r o cedu r e 2 ) Ye s R ep l ace U W B A nt enna No U W B f unc t i oni ng ok? No U se t he r i gh t s e tti[...]

2Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 67 Procedure 1: UWB Antenna connection check Procedure 2: UWB SG setting check Procedure 3: UWB Module connection check Procedure 1 UWB Antenna connection check Use windows application to check device can work fine or not. If an error[...]

2Troubleshooting Procedures 2.28 3G Troubleshooting STA R T Per f or m di agnos t i c t e st ( P r oce dure 1) W as a 3G probl em det ect ed? P er for m con nect or and r epl acem ent check ( P r oce dure 2) R e pl ac e 3G a nt enna / uni t R epl ace syst em bo ar d EN D Ye s 3 G sy st em is no t fa u lty . C o n tin u e t r oubl es hoot i ng - r e[...]

2Troubleshooting Procedures Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual 69 Procedure 1 Connector and replacement check The 3G antenna, 3G unit or system board may be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and perform the follo[...]

3 Tests and Diagnostics Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D Chapter 3 Tests and Diagnostics[...]

3. Tests and Diagnostics Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D 2 Contents 3.1 The Diagnostic Test ........................................................................................................ .... 3 3.2 Executing the Diagnostic Test.............................................................[...]

3 Tests and Diagnostics Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D 3.1 The Diagnostic Test This chapter explains how to use the Test & Diagnostic program to test the functions of the (Base on Bradford 10AR/10ARG T&D version 1.0) hardware modules. The Test & Diagnostic Program is stored on the T&a[...]

3. Tests and Diagnostics Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D 4 3.2 Executing the Diagnostic Test DOS is required to run the DIAGNOSTICS PROGRAM. To start the DIAGNOSTIC PROGRAM, follow these steps: Insert the diagnostics USB disk drive and turn on the computer. (The diagnostics diskette contains the F[...]

3 Tests and Diagnostics The below display will show up at the beginning of T&D program If the test result passes, the following display will show up: Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D[...]

3. Tests and Diagnostics If an error is detected and a test fails, the following message displays: Then press any key for next actions – the below display presented if copying test log file onto diskette is necessary. This action will be executed when “ Y ” key pressed. Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Serie[...]

3 Tests and Diagnostics It will skip this process if “N” key pressed. And then it will check if it’s necessary to leave this program. Program will quit when “ Y ” key pressed and it will go back main menu f or next test if “ N ” key pressed. Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D[...]

3. Tests and Diagnostics 3.3 Display Configuration This Item will show the unit configuration. It includes:  CPU (CPU type)  DDRAM SIZE  Panel ID  HDD1 type & capacity (Vendor ID. M odel .Firmware)  VRAM size / VGA CHIP TYPE  Battery cell (3cell;6cell;12cell)  Wireless type  LAN Type  Bluetooth The screen should displ[...]

3 Tests and Diagnostics 3.4 Audio sound test The audio sound test allows the user to aurally confirm the speaker functions. And the speaker will send out music during test. NOTE : Remember to tune up the volume as “ Maximum ” before this test starts. Buffalo only have one speaker, no need test Left/Right Speaker The screen should display as bel[...]

3. Tests and Diagnostics 3.5 Fan ON/OFF Test The fan test allows the user to test aurally whether the fan is working. And follow the below procedures for this test:  The computer will let the fan be “ON” after any key pressed. Feel the wind or listen the rotating sound to check whether the fan is working or not. NOTE : Remember to approach f[...]

3. Tests and Diagnostics 3.6 Main Battery Charge Test NOTE : The AC adaptor should be connected to successfully run this test . 75W with 19V DC for UMA SKU . 120W with 19V DC for discrease SKU This test shows and measures the main battery:  Battery type (Lion)  Manufacturer (Sanyo/Panasonic/Sony)  Remain charge capacity (0 ~ 100%)  Char[...]

3. Tests and Diagnostics 3.7 Main Battery Change Test 3. 7 FDD Test NOTE : Before running the FDD test, prepare a formatted work diskette (1.44 MB). Need to insert FDD when power on machine. Otherwise the Floppy can not be detected. The Floppy Disk Test includes three subtests of the: 1. Sequential seek/verify function (Range: Track 0 ~ 79) 2. Funn[...]

3. Tests and Diagnostics 3.8 Memory check This test will check if the computer’s Mem ory Frequency and Size is correct in every slot. Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D[...]

3 Tests and Diagnostics 3. 9 Keyboard Test The keyboard test checks the all keys function. NOTE: The Num Lock and the Overlay mode must be off to execute the keyboard test. Before keyboard test starts, the keyboard matrix code should be chosen as below display: 1. S (US, for America) 2. J (Japan, for Japan) 3. K (UK, for Europe) When you execute th[...]

3. Tests and Diagnostics US Keyboard Japan keyboard Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D[...]

3 Tests and Diagnostics UK keyboard Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D 16[...]

3. Tests and Diagnostics NOTE: The “ Fn ” key cannot be tested in the keyboard test. To determine whether the “ Fn ” key is working correctly, press “ Fn+F6 ” or “ Fn + F7 ” keys to check if LCD display brightness change gradually. 3.10 Mouse (Pad) Test The Mouse test allows the user to select and assign values to the following, usi[...]

3. Tests and Diagnostics Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D 18 It will indicate whether the subtests pass or fail after three questions. NOTE: The above figure has three compartments although the Touch Pad installed may only have two buttons. In this case, the central compartment in the figure does n[...]

3. Tests and Diagnostics 3.12 Magnetic Switch Test The Magnetic switch test checks the Magnetic function of the unit. When LCD cover closed, the Magnetic should enable to turn off the display. Follow below steps to run this test: 1. Close the LCD cover. 2. Open the LCD. Then it will indicate whether the test is passed or failed. 1>. If the Magne[...]

3. Tests and Diagnostics 2>. If the Magnetic switch test pass, it will show below display: Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D 20[...]

3. Tests and Diagnostics Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D 3.13 LAN Test The LAN test checks the LAN full-duplex environment. NOTE: LAN loopback needs to plug in before test begins. And LAN information will show on the test screen:  IO Base – Port: A000H  IRQ – BH, it’s “IRQ B”.  [...]

3. Tests and Diagnostics The screen should display as below, indicating whether the subtests pass or fail when finished. Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D 22[...]

3. Tests and Diagnostics If an error is detected and a test fails, the following message displays: Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D[...]

3. Tests and Diagnostics 3.14 RTC Test Checks the computer’s RTC (Real Time Clock) and calendar functions by com paring the DOS and CMOS values. The test runs automatically. The screen should display as below, indicating whether the test is passed or failed when finished. Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series [...]

3. Tests and Diagnostics 3.15 BUTTON TEST NOTE : Only for five buttons SKU. The tool for five buttons SKU, the Screen would display as below: Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D[...]

3. Tests and Diagnostics Mechanical type buttons x 8 to relate with above showed. BUTTON A  ECO BUTTON B  Quick start BUTTON C  Play/Pause BUTTON D  FR BUTTON D  FF BUTTON D  Mute BUTTON D  Volume - BUTTON D  Volume + Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D 26[...]

3. Tests and Diagnostics 3.16 1 st HDD Test The HDD test allows the user to verify the 1 st HDD ok or not. First, please select HDD test method, Screen would display as below: After you select the method, then input password: “hard disk”, if input password is Right, the screen would display as below: If input password is wrong, the screen would[...]

3. Tests and Diagnostics The screen will display as below picture to show the subtest is passed or failed when finished: If it is show the picture as below, it means HDD function is OK If the picture shows as below, it means he HDD function is NG Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D 28[...]

3. Tests and Diagnostics 3.17 Read DMI Compal write Toshiba Part No (version), Toshiba Serial No (Serial No), Product Name, OEM string and UUID , If you want to double check the DMI data, please select Read DMI item, the figure below will be displayed: Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D[...]

3. Tests and Diagnostics 3.18 Write DMI When you want to write DMI data, please select which data you want to write, the figure below will be displayed: 1. Write OME string Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D 30[...]

3. Tests and Diagnostics 2. Write Version 3. Write Serial 4. Write Product After write OK, you should reboot the system that can make the setting effective, or you can write next data before reboot system, the figure below will displayed: Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D[...]

3. Tests and Diagnostics NOTE : should input correct DMI data, and should reboot the system that can make the setting effective. Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D 32[...]

3. Tests and Diagnostics 3. 19 3D Sensor Test This test will check 3D Sensor function by your computer successful or not. NOTE : Steps 1  Keep test unit on platform which must be a flat horizontal surface, then click enter to test Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D[...]

3. Tests and Diagnostics NOTE : Steps 2  Keep test unit vertical with platform, then click to test NOTE : Steps 3  Turn run 90 degree whirl, then click enter to test Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D 34[...]

3. Tests and Diagnostics NOTE : Steps 4  Go on Turn run 90 degree whirl, then click enter to test NOTE : Step5  Go on Turn run 90 degree whirl, then click enter to test Check test result as below picture, PASS will show “OK”, FAIL will show “NG”. Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D[...]

3. Tests and Diagnostics Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D 36[...]

3. Tests and Diagnostics Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T& D[...]

Chapter 4 Replacement Procedures[...]

4 Replacement Procedures Satellite A500D Main tenance Manual 4-ii Chapter 4 Contents 4.1 General ................................................................................................................... 4-1 Safety Precautions .......................................................................................... 4-2 Before You Begin...[...]

4 Replacement Procedures Satellite A500D Main tenance Manual 4-iii Installing the Keyboard Cover and Keyboard .............................................. 4-24 4.9 Logic Upper Assembly......................................................................................... 4-25 Removing the Logic Upper Assembly ...................................[...]

4 Replacement Procedures Satellite A500D Main tenance Manual 4-iv Installing the VGA Board and VGA Thermal Module ................................ 4-41 4.19 CPU and Thermal Module ................................................................................... 4-42 Removing the CPU and Thermal Module .............................................[...]

4 Replacement Procedures Satellite A500D Main tenance Manual 4-v Figures Figure 4.1 Removing the Battery Pack ........................................................................... 4-8 Figure 4.2 Removing the HDD door ............................................................................. 4-10 Figure 4.3 Removing the HDD from the HDD bay[...]

4 Replacement Procedures Satellite A500D Main tenance Manual 4-vi Figure 4.32 Removing the VGA Board ........................................................................... 4-40 Figure 4.33 Reapply the Shinetsu 7726 grease on the thermal m odule and remove any release papers .................................................................... 4[...]

4 Replacement Procedures Satellite A500D Mainte nance Manual 4-vii Figure 4.60 Removing the LVDS cable from the LCD module ..................................... 4-61 Figure 4.61 Installing the LCD Hinge Assembly ............................................................ 4-62 Figure 4.62 Installing the LCD Module from the LCD cover assem bly (high[...]

[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 4.1 General This chapter explains how to disassemble the laptop and replace Field Replaceable Units (FRUs). Some replacement procedures m ay not require you to remove all the surrounding FRUs to replace only one FRU. The chart below shows the FRUs in the order in which the[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. Satellite A500D Main tenance Manual 4-2 Safety Precautions Before you begin disassembly read the following safety precautions carefully. Be sure to follow them while you are working. DANGER: 1. Always use the original batteries or replacement batteries authorized by Toshib[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Satellite A500D Main tenance Manual 4-3 CAUTION: 1. Before replacing a component, make sure that the replacement component meets the required specifications. To avoid laptop failures, never use components that do not meet the specifications. 2. To avoid internal damage suc[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. Satellite A500D Main tenance Manual 4-4 Before You Begin Before you begin to disassemble the laptop, keep in mind the precautions and advice in this section. Always begin disassembly by removing the AC adapter and battery pack. Rem ove the optional parts and accessories as[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Satellite A500D Main tenance Manual 4-5 Disassembly Procedures The cable connectors come in these two basic types:  Pressure plate connectors  Normal pin connectors To remove a pressure plate connector, pull up the tabs on either side of the connector's plastic [...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. Satellite A500D Main tenance Manual 4-6 Tools and Equipment For your safety and that of other people in the working environment, it is strongly recomm ended that you use electrostatic discharge (ESD) equipment. The proper use of this equipment will ensure successful repair[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Satellite A500D Main tenance Manual 4-7 Colors of Screw Shanks For easy identification of the correct screws, the screw shanks are colored according to their lengths, as follows:  Screws of an odd-numbered length Blue  Screws of a special length Black Screws of a spe[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4.2 Battery Removing the Battery Pack Remove the battery pack according to the following procedures and Figure 4.1. CAUTION: When handling the battery packs, use care not to short circuit the terminals. Do not drop, hit, twist, or bend the battery packs. Do not scratch or [...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Satellite A500D Main tenance Manual 4-9 Installing the Battery Pack Install the battery pack according to the following procedures. CAUTION: The battery packs contain a lithium ion battery, which can explode due to improper replacement, use, handling or disposal. Always di[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4.3 HDD Removing the HDD CAUTION: Do not press on the top or bottom of the drive. Applying such pressure can either corrupt the data in the drive or damage the drive. Remove the HDD (hard disk drive) according to the following procedures and Figures 4.2 and 4.3. 1. To remo[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 2. Pull the tab right to remove the HDD module. Figure 4.3 Removing the HDD from the HDD bay NOTE: Do not disassemble the HDD pack when it is working normally. Disassemble or replace the HDD pack only if it fails. 3. Place the HDD pack on a flat surface such as a desk. 4. [...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. Satellite A500D Maintenance Manual 4-12 CAUTION: Do not apply pressure to the top or bottom of the drive. Installing the HDD Install the HDD according to the following procedures. CAUTION: To avoid damage, always hold the HDD only by its sides. 1. Place the HDD into the HD[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 4.4 Memory Removing the Optional Memory Remove the optional mem ory according to the following procedures and Figure 4.5 after checking that the laptop is turned off. CAUTION: Remove the optional memory after turning off the laptop. If this is violated, the laptop or memor[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4. Spread out the two memory lock latches so that the m emory pops up. Please follow the procedure as shown in Figure 4.6. Figure 4.6 Removing the RAM from the connectors 5. Pull the memory up and out at an angle, using care to avoid touching the connectors. Installing the[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 4.5 UWB Module Removing the UWB Module Remove the UWB m odule according to the following procedures and Figure 4.7. 1. Detach the antenna on the UWB card. 2. Disconnect two antenna cables and remove two M2x4 screws that secure the UWB card. 3. Pull the UWB module out at an[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4.6 Modem Card / FM Tuner Removing the Modem Card Remove the modem card according to the following procedures and Figure 4.8. 1. Remove two M2.5x3 screws that secure the modem card. 2. Flip the modem card over, and detach the cable connected to the card. M2.5x3*2 Figure 4.[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Removing the FM Tuner Remove the FM Tuner and FM jack according to the following procedures and Figure 4.9. 1. Remove two M2.5x3 screws from the FM tuner. 2. Detach the two cables from the front and back of the FM tuner. Figure 4.9 Removing the FM Tuner Installing the Mode[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. Satellite A500D Maintenance Manual 4-18 Installing the FM Tuner 1. Attach the cable on the back of the FM Tuner. 2. Seat the FM Tuner in the correct position on the motherboard and attach the cable on the front of the FM Tuner to the motherboard. 3. Secure the FM Tuner to [...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 4.7 ODD Removing the ODD Bay Module NOTE: The installation and removal procedures are the same for all the modules that can be installed in the ODD bay. See the appropriate sections for the disassembly procedures of specific modules. Remove the ODD bay module according to [...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. Installing the ODD Bay Module Install the ODD bay module according to the following procedures. 1. Place the ODD bay module in the correct position and slide it in. 2. Push it in until it meets the end. 3. Secure the ODD bay module with one M2.5x6 screw. Disassembling the [...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Satellite A500D Maintenance Manual 4-21 Assembling the ODD Drive Assemble the ODD drive according to the following procedures. 1. Seat the bracket in the correct position. 2. Secure them with two M2×3 screws.[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4.8 Keyboard Cover and Keyboard Removing the Keyboard Cover and Keyboard Remove the Keyboard Cover and Keyboard according to the following procedures and Figures 4.12, 4.13, 4.14 and 4.15. 1. Close the laptop and turn over. Remove two M2x4 screws from inside the battery lo[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Figure 4.13 Removing the keyboard cover 4. Remove four M2x3 screws. M2x3*4 Figure 4.14 Removing screws from the keyboard Satellite A500D Maintenance Manual 4-23[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 5. Lift the keyboard up and detach the cable on the back of the keyboard from the motherboard. Figure 4.15 Removing the keyboard Installing the Keyboard Cover and Keyboard Install the keyboard cover and keyboard according to the following procedures. 1. Attach the cable on[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 4.9 Logic Upper Assembly Removing the Logic Upper Assembly Remove the logic upper assembly according to the following procedures and Figure 4.16, 4.17 and 4.18. 1. Turn the laptop upside down and remove the following 17 screws:  Fifteen M2.5x8 screws  Two M2.5x4 scre[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 2. Turn to the front and remove the following screws:  Five M2.5x8 screws  Three M2.5x5 screws M2.5x5*3 M2.5x8*5 Figure 4.17 Removing eight screws from the laptop. Satellite A500D Maintenance Manual 4-26[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 3. Detach eight connectors: one Power board FFC, one Control Panel FFC, two Speaker cables, one Fingerprinter FFC, one LED Bo ard cable, one Bluetooth cable and one TouchPad cable as shown in Figure 4.18. Figure 4.18 Detaching cables from the laptop 4. Lift up the logic up[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4.10 Power Board Removing the Power Board Remove the power board according to the following procedures and Figure 4.19. 1. Remove two M2.5x4 screws from the power board. 2. Separate the power board from the logic upper assembly. M2.5x4*2 Figure 4.19 Removing the power boar[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 4.11 Speakers Removing the Speakers Remove the Speakers according to the following procedures and Figure 4.20. 1. Hold the speaker in place and then remove four special M2.5x6 screws from the left and right speaker. 2. Remove the left and right speakers from the logic uppe[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4.12 Bluetooth Card Removing the Bluetooth card Remove the Bluetooth card according to the following procedures and Figure 4.21. 1. Remove the Bluetooth cable from the Bluetooth card. 2. Press down the latch and push the Bluetooth card in the direction indicated in the fig[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 4.13 Touchpad Bracket, Touchpad Boards and Fingerprint Board Removing the Touchpad Bracket, Touc hpad Boards and Fingerprint Board Remove the Touchpad bracket, Touchpad boards (the button board and switch board) and Fingerprint board according to the following procedures a[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 5. Pull the Fingerprint board up to remove it from the logic upper assem bly. M2.5x3*1 M2.5x4*1 Figure 4.23 Removing the Touchpad boards and Fingerprint board Installing the Touchpad Bracket, Touchpad Boards and Fingerprint Board/Touchpad Switch Board Install the Touchpad [...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 4.14 LED board Removing the LED Board To remove the LED board from the logic lower assem bly: 1. Remove one M2.5x4 screw and remove one cable from the motherboard as described in Figure 4.24 below. M2.5x4*1 Figure 4.24 Removing the LED Board Installing the LED Board Instal[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4.15 Thermal Fan Removing the Thermal Fan Remove the thermal fan according to the following procedures and Figure 4.25. 1. Detach the cable from the motherboard. 2. Remove one M2.5x8 screw from the therm al fan. Remove the thermal fan cable. 3. Remove the thermal fan from [...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 4.16 WLAN Card Removing the WLAN Card Remove the WLAN Card according to the following procedures and Figure 4.26. 1. Remove two M2x4 screws from the W LAN Card. 2. Remove the WLAN Card from the motherboard. M2x4*2 Figure 4.26 Removing the WLAN Card Installing the WLAN card[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4.17 Motherboard Removing the Motherboard Remove the motherboard according to the following procedures. 1. Remove one M2.5x4 screw and five cables from the logic lower assem bly as indicated by arrows in Figure 4.27. M2.5x4*1 Figure 4.27 Removing motherboard from logic low[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 2. Remove the DC_IN CONN and cable out of the l ogic lower assembly from right to left, as shown in Figure 4.28. Figure 4.28 Removing the DC_IN CONN and cable 3. Use left hand to hold down the lower part of the motherboard and right hand to pick the motherboard up as shown[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. Installing the Motherboard Install the motherboard according to the following procedures. 1. Before seating the motherboard on the logic lower assembly, pull out the Left USB cable and LDVS cable to avoid being pressed. 2. Align the DP CONN, S/PDIF CONN, Audio CONN and RJ4[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 3. Put the DC_IN CONN in the lower DC_IN trough a nd route the cable from left to right under the cable-fixed Rib as shown in Figure 4.31. Figure 4.31 Installing the DC-in jack 4. Secure one M2.5x4 screw. 5. Attach five cables to the motherboard as indicated by arrows in F[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4.18 VGA Board and VGA Thermal Module (Optional) Removing the VGA Board and VGA Thermal Module Remove the VGA board and thermal m odule according to the following procedures and Figures 4.32, 4.33. CAUTION: When removing the VGA board and VGA thermal module, keep the follo[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Installing the VGA Board and VGA Thermal Module Install the VGA board and thermal Module according to the following procedures. 1. Reapply Shinetsu 7762 grease on the VGA thermal module as shown in Figure 4.33. If you use one new VGA thermal module, rem ove the release pap[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4.19 CPU and Thermal Module Removing the CPU and Thermal Module Remove the CPU and the CPU thermal m odule according to the following procedures and Figures 4.34, 4.35. CAUTION: When removing the thermal module, keep the following in mind: 1. The thermal module can become [...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures CAUTION: When removing the CPU, keep the following in mind: The CPU can become very hot during operation. Be sure to let it cool down before starting repair work. 3. Unlock the CPU by rotating the cam on the CPU socket counterclockwise to the unlock position with a flat-bl[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. CAUTION: When installing the thermal module, keep the following in mind: 1. Be sure to confirm the correct position for the module. 2. Secure the relevant screws on the motherboard according to the number sequence sealed on the thermal module. 4. Reapply Shinetsu 7762 grea[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 4.20 Display Assembly Removing the Display Assembly CAUTION: Use care to avoid the antenna cable being caught between the display assembly and the laptop. Remove the display assembly according to the following procedures and Figure 4.37. 1. Remove six M2.5x6 screws securin[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4.21 LCD Bezel Assembly Removing the LCD Bezel Assembly The LCD comes in two different models: a high-end assem bly model and a low-end assembly model. Remove the LCD bezel assem bly of each model according to the following procedures. For Low-end Model 1. Remove four scre[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 2. Peel off the bezel from left and right side as shown in Figure 4.39. Figure 4.39 Peel off the bezel 3. Pull out the bezel hinge wall from the cover hinge wall as shown in Figure 4.40. Figure 4.40 Pull out the hinge wall 4. Pull apart the lower half of the bezel; leave t[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 5. Push the bezel from the left and right side as shown in Figure 4.41 and remove the bezel from the display assembly. Figure 4.41 Remove the bezel For High-end Model 1. For the high-end model, remove two screw rubbers on the LCD bezel and rem ove two M2.5x6 screws as show[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 2. Wrap the flat blade screwdriver with three layers of tape. Figure 4.43 Wrap the flat blade screwdriver with tape 3. Press the bezel hinge wall and cover hinge wall as indicated in Figure 4.44. Figure 4.44 Press the hinge wall Satellite A500D Maintenance Manual 4-49[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4. When pressing the hinge wall, use the flat blade screwdriver to pry up the bezel hinge wall as indicated in Figure 4.45 to release the first hook on the right side. Figure 4.45 Pry up the bezel hinge wall 5. Use both hands to release the rest of the hooks as indicated i[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 6. Hold the hinge wall with your left hand, and push the right side of the bezel upward with right hand thumb as indicated in Figure 4.47. Figure 4.47 Push the right side of the bezel upward Satellite A500D Maintenance Manual 4-51[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 7. Hold the hinge wall with your right hand, and push the left side of the bezel upward with left hand thumb as indicated in Figure 4.48. Figure 4.48 Push the left side of the bezel upward Satellite A500D Maintenance Manual 4-52[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 8. Release the hooks from the bottom left and bottom right of the bezel with the wrapped screwdriver as shown in Figure 4.49. Figure 4.49 Release hooks from the bottom of the bezel 9. Release the hooks on the right side of the bezel with the wrapped screwdriver as indicate[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 10. Release the hooks on the upper side of the bezel from left to right with the wrapped screwdriver as indicated in figure 4.51. Figure 4.51 Release the hooks from the upper side of the bezel 11. Remove the bezel from the display assembly Satellite A500D Maintenance Manua[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Installing the Display Mask Install the LCD bezel assembly according to the following procedures. 1. Seat the LCD bezel assembly in the correct position. 2. For the low-end model, press the bezel hinge wall against the cover hinge wall as shown in Figure 4.52. For the high[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4. For the low-end model, press the left and right side of the bezel as shown in Figure 4.54. For the high-end model, press and secure the hooks on the left and right side of the bezel. Figure 4.54 Press the left and right side of the bezel for the low-end model/ Press the[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 4.22 LCD Module and Inverter Board Removing the LCD Module and Inverter Board Remove the LCD module and the inverter board according to the following procedures and Figures 4.56, 4.57, 4.58, 4.59 and 4.60. 1. Remove one M2x3 screw securing the inverter board and detach two[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 2. a. For the high-end model, remove eight M2.5x4 screws securing the LCD m odule according to the sequence indicated in the Figure 4.57. Satellite A500D Maintenance Manual 4-58 1 4 3 2 M2.5x4*8 1 4 3 2 Figure 4.57 Removing the LCD Module from the LCD cover assembly (high-[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures b. For the low-end model, remove six M2.5x4 screws securing the LCD m odule according to the sequence indicated in the Figure 4.58. M2.5x4*6 12 3 3 2 1 Figure 4.58 Removing the LCD Module from the LCD cover assembly (low-end model) 3. Lift the LCD module out of the LCD cov[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4. Remove six M2x3 screws according to the sequence indicated in the Figure 4.59, and then remove the LCD hinge assembly. M2x3*6 2 2 1 1 3 3 Figure 4.59 Removing the LCD Hinge Assembly 5. Turn the LCD module over and place it face down on a protective surface, such as a fo[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 6. Remove the tape and LVDS cable connector. Then detach the LVDS cable. Figure 4.60 Removing the LVDS cable from the LCD module NOTE: Integrated Circuits (ICs) are fragile. Use extreme care not to apply pressure to the ICs along the edges of the LCD module. Dispose of use[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. Installing the LCD Module and Inverter Board Install the inverter board according to the following procedures. 1. Turn the LCD module cover and place it face down on a protective surface such as a foam pad. 2. Connect the LVDS cable to the LCD panel connector. 3. Turn the [...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 5. Seat the LCD module in the correct position in the LCD cover assembly. Secure it to the LCD cover assembly with eight M2.5x4 screws for the high-end model, or with six M2.5x4 screws for the low-end model, according to the sequence indicated in Figure 4.62 and Figure 4.6[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 1 2 3 M2.5x4*6 32 1 Figure 4.63 Installing the LCD Module from the LCD cover assembly (low-end model) 6. Seat the inverter board in correct position and connect two cables to the two ends of the inverter board. Then secure it with one M2x3 screw. Satellite A500D Maintenanc[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures NOTE: Be careful not to pinch codes beside hinges. Figure 4.64 Not to pinch codes beside hinges (high-end model) Figure 4.65 Not to pinch codes beside hinges (low-end model) Satellite A500D Maintenance Manual 4-65[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4.23 CMOS Board and MIC Removing the CMOS Board and MIC Remove the CMOS Board and MIC according to the following procedures and Figure 4.66 and 4.67. 1. Disconnect the CMOS cable from the CMOS module connector and rem ove the CMOS board. Figure 4.66 Removing the CMOS board[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Figure 4.67 Removing the CMOS board and MIC (low-end model) 2. Lift the MIC cable from the LCD cover assembly. Installing the CMOS Board and MIC Install the CMOS Board and MIC according to the following procedures. 1. Connect the CMOS module cable to CMOS module connector.[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4.24 Left USB Board Removing the USB Board on the Left Side Remove the left USB board according to the following procedures and Figure 4.68. 1. Remove the USB board from the left side of the logic lower assem bly using one M2.5x4 screw. M2.5x4 Figure 4.68 Removing the left[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 4.25 Right USB Board Removing the Right USB Board on the Right Side Remove the Right USB board according to the following procedures and Figure 4.69. 1. Wrap a flat balde screwdriver with three layers of tape. Figure 4.69 Wrap the flat blade screwdriver with tape 2. Discon[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 3. Tear the FFC cable up from the logic lower assembly. Figure 4.70 Wrap the flat blade screwdriver with tape 4. Pry up the right USB Board from the right side with a flat blade screwdriver wrapped with three layers of tape. Be careful not to scratch the FFC cable. Figure [...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Satellite A500D Maintenance Manual 4-71 Installing the Right USB Board Install the Right USB board according to the following procedures. 1. Seat the USB board in the correct position on the right side of the logic lower assembly. 2. Secure the USB board to the logic lower[...]

Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assem bly or disassembly. Observe the following precautions when handling it to prevent damaging it. 1. When installing the LCD module in the display assem bly, make sure that you seat it so that it is properly aligned a[...]

3. If the panel’s surface gets dirty or moist, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to a soft cloth and then wipe the panel’s surface. Do not apply cleanser directly [...]

5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle grounding device when handling the module. Satellite A500D/Pro A500D Series Maintenance [...]

7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below its specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. 9. Do not disassemble the LCD module. Disassem bly can cause malfunctions. A-4 [CONFIDENTIAL][...]

10. If you transport the module, do not use packing material that contains epoxy resin (am ine) or silicon glue (alcohol or oxime). These materials can release gas that can dam age the panel’s polarization. Satellite A500D/Pro A500D Series Maintenance Manual [CONFIDENTIAL] A-5[...]

Appendix B Appendix B Board Layout B.1 System Board T op View Figure B-1 System Board Layout (Top) JCS JBLG JBT JMIC JCAM JUSBB2 JSPKL JWLAN JPOWER JUSBB1 JKB PJP1 JSPKR JFAN JLVD JTOUCH JLIGHT JFP U54 JEXP JFEL UL1 JLED UC1 U46 SatelliteA500D/Pro A500D Maintenance Manual [CONFIDENTIAL] B-1[...]

B.2 System Board Bottom V iew PJP2 JDDRH JGPS JDDRL U3 Figure B-2 System Board Layout (Bottom) Table B-1 System Board ICs (top and bottom) JBCAS1 JCRT / JDP JLAN JHDMI JESATA JEXMIC JLINE JFM JHDD0 JMDC JMXM JNAND JODD JREAD JSSD JCPU U33 U10 UA2 U15 B-2 [CONFIDENTIAL] Satellite A500D/Pro A500D Maintenance Manual[...]

Number Name U3 North bridge AMD RS780/RX781 U10 Clock Generator SLG8SP626VTR U15 South bridge AMD SB700 U33 KB926QFD3(EC) U46 BIOS ROM UA2 ALC272-GR UC1 JMB385(CARD READ) UL1 RTL8111DL U54 G-sensor Table B-2 System Board Connectors (top and bottom) Number Name JCPU CPU Socket JFAN Fan conn. JDDRH, JDDRL DDRII conn. JCRT CRT conn. JBCAS1 B-CAS conn [...]

B-4 [CONFIDENTIAL] Satellite A500D/Pro A500D Maintenance Manual JLED LED/B conn. JCS CapSensor/B conn. JFM FMTuner/B conn. JESATA eSATA conn. JHDMI HDMI conn JLAN LAN conn. JLINE Headphones conn. JEXMIC External MIC conn. JLIGHT Light Pipe conn JLVDS LVDS conn. JLINE HeadPhone/LINE Out JACK conn JGPS GPS conn. JMDC MDC conn JMXM MXM conn JNAND WUSB[...]

C. Appendix C Pin Assignments System Board C.1 JF AN Table C-1 FAN I/F pin assignments (3-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 +FAN1 2 FAN_SPEED1 3 GND C.2 JFM Table C-2 FM I/F pin assignments (10-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 +3VS 2 +3VS 3 FM_I2CCLK 4 FM_I2CDAT 5 FM_I2C_INT# 6 FM_OUTR 7 FM_OUTL 8 GND 9 GN[...]

17 LCD_TZCLK- O 18 LCD_TXOUT1- O 19 GND 20 LCD_TXOUT2+ O 21 LCD_EDID_CLK O 22 LCD_TXOUT2- O 23 LCD_EDID_DATA O 24 GND O 25 +LCDVDD_R 26 LCD_TZOUT0+ O 27 +LCDVDD_R 28 LCD_TZOUT0- O 29 +3VS 30 LCD_TZOUT1+ O 31 NA 32 LCD_TZOUT1- O 33 +LCD_INV 34 LCD_TZOUT2+ O 35 +LCD_INV 36 LCD_TZOUT2- O 37 +LCD_INV 38 GND 39 +LCD_INV 40 BKOFF# O C.4 JCRT Table C-4 CR[...]

11 GND 12 HDMI_R_CK- O 13 HDMI_CEC O 14 NC 15 HDMI_SCLK O 16 HDMI_SDATA O 17 GND 18 +HDMI_5V_OUT O 19 HDMI_HPD O C.6 JHDD0 Table C-6 1 st HDD I/F pin assignments (22-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 GND 2 SATA_C_TX1+ 3 SATA_C_TX1- 4 GND 5 SATA_C_RX1- 6 SATA_C_RX1+ 7 GND 8 +3VS 9 +3VS 10 +3VS 11 GND 12 GND 13 GND 14 +5VS 15 +5V[...]

C.8 JESA T A Table C-8 1st eSATA/USB I/F pin assignments (11-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 +USB_VCCB 2 USB20_N2_R_ S 3 USB20_P2_R_ S 4 GND 5 GND 6 SATA_C_TX2+ 7 SATA_C_TX2- 8 GND 9 SATA_C_RX2- 10 SATA_C_RX2+ 11 GND C.9 JBT Table C-9 Bluetooth Connector pin assignments (10-pin) Pin No. Signal name Pin No. Signal Name I/O 1 G[...]

Pin No. Signal name I/O Pin No. Signal Name I/O 1 +CAM_VDD 2 USB20_N9_R I/O 3 USB20_P9_R I/O 4 GND 5 GND C.12 JWLAN Table C-12 Wi-Fi/WiMax Connector pin assignments (52-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 NC 2 +3VS 3 WLAN_BT_DATA 4 GND 5 WLAN_BT_CLK 6 +1.5VS 7 CLKREQ_MCARD2# 8 NC 9 GND 10 NC 11 CLK_PCIE_MCARD2# 12 NC 13 CLK_PCIE_[...]

C.13 JEXP Table C-13 New Card Connector pin assignments (26-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 GND 2 USB20_N5 3 USB20_P5 4 CP_USB# 5 NC 6 NC 7 SMB_CK_CLK0 8 SMB_CK_DAT0 9 +1.5VS_CARD 10 +1.5VS_CARD 11 EC_SWI#_R 12 +3VALW_CARD 13 PERST# 14 +3VS_CARD 15 +3VS_CARD 16 CLKREQ# 17 EXP_CPPE# 18 CLK_PCIE_NCARD# 19 CLK_PCIE_NCARD 20 GND [...]

1 +5VALW 2 +5VS 3 DC_IN 4 POWER_LED 5 SUSPEND_LED 6 HDD_LED 7 CR_LEDCON 8 BATT_FULL_LED# 9 BATT_LOW_LED# 10 GND 11 GND 12 GND C.16 JGPS Table C-16 GPS Connector pin assignments (52-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 NC 2 +3VS 3 XBCLKM 4 GND 5 BCCDET 6 +1.5VS 7 CLKREQ_MCARD1# 8 +UIM_PWR 9 GND 10 UIM_DATA 11 CLK_PCIE_MCARD1# 12 UI[...]

51 NC 52 +3VS C.17 JDDRL, JPDDRH Table C-17 SODIMM I/F pin assignments (200-PIN) (1/4) Pin No. Signal name I/O Pin No. Signal Name I/O 1 VREF O 2 VSS O 3 VSS O 4 DQ4 I/O 5 DQ0 I/O 6 DQ5 I/O 7 DQ1 I/O 8 VSS O 9 VSS O 10 DM0 I/O 11 DQS0# I/O 12 VSS O 13 DQS0 I/O 14 DQ6 I/O 15 VSS O 16 DQ7 I/O 17 DQ2 I/O 18 VSS O 19 DQ3 I/O 20 DQ12 I/O 21 VSS O 22 DQ1[...]

53 VSS O 54 VSS O 55 DQ18 I/O 56 DQ22 I/O 57 DQ19 I/O 58 DQ23 I/O 59 VSS O 60 VSS O 61 DQ24 I/O 62 DQ28 I/O 63 DQ25 I/O 64 DQ29 I/O 65 VSS O 66 VSS O 67 DM3 I/O 68 DQS3# I/O 69 NC - 70 DQS3 I/O 71 VSS O 72 VSS O 73 DQ26 I/O 74 DQ30 I/O 75 DQ27 I/O 76 DQ31 I/O 77 VSS O 78 VSS O 79 CKE0 I/O 80 NC/CKE1 I/O 81 VDD O 82 VDD O 83 NC - 84 NC/A15 - 85 BA2 [...]

117 VDD O 118 VDD O 119 NC/ODT1 I/O 120 NC - 121 VSS O 122 VSS O 123 DQ32 I/O 124 DQ36 I/O 125 DQ33 I/O 126 DQ37 I/O 127 VSS O 128 VSS O 129 DQS4# I/O 130 DM4 I/O 131 DQS4 I/O 132 VSS O 133 VSS O 134 DQ38 I/O 135 DQ34 I/O 136 DQ39 I/O 137 DQ35 I/O 138 VSS O 139 VSS O 140 DQ44 I/O 141 DQ40 I/O 142 DQ45 I/O 143 DQ41 I/O 144 VSS O 145 VSS O 146 DQS5# [...]

181 DQ57 I/O 182 DQ61 I/O 183 VSS I/O 184 VSS I/O 185 DM7 O 186 DQS7# O 187 VSS I/O 188 DQS7 I/O 189 DQ58 O 190 VSS O 191 DQ59 - 192 DQ62 - 193 VSS I/O 194 DQ63 - 195 SDA O 196 VSS O 197 SCL I/O 198 SA0 I/O 199 VDDSPD I/O 200 SA1 I/O C.18 JMIC Table C-18 Internal Microphone Connector pin assignments (2-pin) Pin No. Signal name I/O Pin No. Signal Na[...]

3 CAPS_LED# 4 +3VS 5 KSI1 6 KSI6 7 KSI5 8 KSI0 9 KSI4 10 KSI3 11 KSI2 12 KSI7 13 KSO15 14 KSO12 15 KSO11 16 KSO10 17 KSO9 18 KSO8 19 KSO13 20 KSO7 21 KSO6 22 KSO14 23 KSO5 24 KSO3 25 KSO4 26 KSO0 27 KSO1 28 KSO2 29 NC 30 NC 31 KSO17 32 NC 33 KSO16 34 +3VS C.21 JCS Table C-21 FUN/B connector pin assignments (10P-pin) Pin No. Signal name I/O Pin No. [...]

C.23 JREAD Table C-23 CARD READER connector pin assignments (40P-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 XDCD0#_SDCD# 2 XDWP#_SDWP# 3 +VCC_OUT 4 XD_SD_D7 5 XD_SD_D6 6 XD_SD_D5 7 XD_SD_D4 8 XD_SD_MS_D3 9 XD_SD_MS_D2 10 XD_SD_MS_D1 11 GND 12 XD_SD_MS_D1 13 SDCMD_MSBS_X DWE# 14 XD_SD_MS_D0 15 XD_SD_MS_D1 16 XD_SD_D7 17 XD_SD_MS_D0 18 XD[...]

5 GND C.25 JSPKL Table C-25 SPKL connector pin assignments (4P-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 SPK_L1 2 SPK_L2 3 NC 4 NC C.26 JSPKR Table C-26 SPKR connector pin assignments (4P-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 SPK_R1 2 SPK_R2 3 NC 4 NC C.27 JTOUCH Table C-27 T/P connector pin assignments (4P-pin) Pin No[...]

C.29 JBLG Table C-29 KEYBOARD BACKLIGHT connector pin assignments (4P-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 +5VS_LED 2 NC 3 NC 4 GND C.30 JDP Table C-30 Display Port connector pin assignments (20P-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 DP_R_TXD0+ 2 GND 3 DP_R_TXD0- 4 DP_R_TXD1+ 5 GND 6 DP_R_TXD1- 7 DP_R_TXD2+ 8 GND [...]

C.32 JLIGHT Table C-32 Light Pipeconnector pin assignments (4P-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 +5VS 2 L_LED# 3 KSI6 4 KSO0 5 GND 6 GND C.33 JMDC Table C-33 MDC pin assignments (12P-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 GND 2 +3VALW 3 HDA_SDOUT_MDC 4 NC 5 GND 6 +3VALW 7 HDA_SYNC_MDC 8 GND 9 HDA_SDIN1 10 GND 11[...]

13 +MXM_B+ 14 +1.8VS_MXM 15 +MXM_B+ 16 RUNPWROK 17 GND 18 +5VALW_MXM 19 GND 20 GND 21 GND 22 GND 23 GND 24 GND 25 PCIE_GTX_C_MRX_N15 26 GND 27 PCIE_GTX_C_MRX_P15 28 PCIE_MTX_C_GRX_N15 29 GND 30 PCIE_MTX_C_GRX_P15 31 PCIE_GTX_C_MRX_N14 32 GND 33 PCIE_GTX_C_MRX_P14 34 PCIE_MTX_C_GRX_N14 35 GND 36 PCIE_MTX_C_GRX_P14 37 PCIE_GTX_C_MRX_N13 38 GND 39 PCI[...]

83 GND 84 PCIE_MTX_C_GRX_P6 85 PCIE_GTX_C_MRX_N5 86 GND 87 PCIE_GTX_C_MRX_P5 88 PCIE_MTX_C_GRX_N5 89 GND 90 PCIE_MTX_C_GRX_P5 91 PCIE_GTX_C_MRX_N4 92 GND 93 PCIE_GTX_C_MRX_P4 94 PCIE_MTX_C_GRX_N4 95 GND 96 PCIE_MTX_C_GRX_P4 97 PCIE_GTX_C_MRX_N3 98 GND 99 PCIE_GTX_C_MRX_P3 100 PCIE_MTX_C_GRX_N3 101 GND 102 PCIE_MTX_C_GRX_P3 103 PCIE_GTX_C_MRX_N2 104[...]

151 GND 152 GND 153 NC 154 NC 155 NC 156 NC 157 NC 158 VGA_SPDIF 159 VGA_AUXN 160 VGA_LCD_TZOUT2- 161 VGA_AUXP 162 VGA_LCD_TZOUT2+ 163 GND 164 GND 165 NC 166 VGA_LCD_TZOUT1- 167 NC 168 VGA_LCD_TZOUT1+ 169 GND 170 GND 171 NC 172 VGA_LCD_TZOUT0- 173 NC 174 VGA_LCD_TZOUT0+ 175 GND 176 GND 177 VGA_DP3- 178 VGA_LCD_TXCLK- 179 VGA_DP3+ 180 VGA_LCD_TXCLK+[...]

219 VGA_HDMI_TXD1- 220 VGA_HDMI_CLK 221 VGA_HDMI_TXD1+ 222 NC 223 GND 224 GND 225 VGA_HDMI_TXD0- 226 +3VS_MXM 227 VGA_HDMI_TXD0+ 228 +3VS_MXM 229 GND 230 +3VS_MXM C.35 JNAND Table C-35 NAND pin assignments (52-PIN) Pin No. Signal name I/O Pin No. Signal Name I/O 1 NC 2 +3VS 3 NC 4 GND 5 NC 6 +1.5VS 7 NC 8 NC 9 GND 10 NC 11 CLK_PCIE_MCARD3# 12 NC 13[...]

49 NC 50 GND 51 NC 52 +3VS C.36 JSSD Table C-36 SSD pin assignments (16-PIN) Pin No. Signal name I/O Pin No. Signal Name I/O 1 GND 2 SATA_C_TX0+ 3 SATA_C_TX0- 4 GND 5 SATA_C_RX0- 6 SATA_C_RX0+ 7 GND 8 +3VS 9 +3VS 10 GND 11 GND 12 NC 13 NC 14 NC 15 NC 16 NC C.37 JUSBB1 Table C-37 USB LEFT pin assignments (6-PIN) Pin No. Signal name I/O Pin No. Signa[...]

C-22 [CONFIDENTIAL] SatelliteA500D/ProA500D Maintenance Manual 11 USB20_P1_R 12 GND[...]

Appendix D Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 01 ‘ ~ 29 A9 0E F0 0E 02 1 ! 02 82 16 F0 16 03 2 @ 03 83 1E F0 1E 04 3 # 04 84 26 F0 26 05 4 $ 05 85 25 F0 25 06 5 % 06 86 2E F0 2E 07 6 ^ 07 87 36 F0 36 08 7 & 08 88 3D F0 3D *2 09 8[...]

Table D-1 Scan codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 29 | 2B AB 5D F0 5D *5 30 Caps Lock 3A BA 58 F0 58 31 A 1E 9E 1C F0 1C 32 S 1F 9F 1B F0 1B 33 D 20 A0 23 F0 23 34 F 21 A1 2B F0 2B 35 G 22 A2 34 F0 34 36 H 23 A3 33 F0 33 37 J 24 A4 3B F0 3B *2 38 K 25 A5 42 F0 42 *2 39 L 26 A6 4B F0 4B *2[...]

Table D-1 Scan codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 58 Ctrl(L) 1D 9D 14 F0 14 *3 60 Alt (L) 38 B8 11 F0 11 *3 61 Space 39 B9 29 F0 29 62 ALT (R) E0 38 E0 B8 E0 11 E0 F0 11 64 Ctrl(R) E0 1D E0 9D E0 14 E0 F0 14 75 Ins E0 52 E0 D2 E0 70 E0 F0 70 *1 76 Del E0 53 E0 D3 E0 71 E0 F0 71 *1 79 [...]

Table D-1 Scan codes (set 1 and set 2) (4/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 07 F0 07 *3 124 PrintSc *6 *6 *6 *6 *6 126 Pause *7 *7 *7 *7 *7 X Fn — — — — *4 X Win E0 5B E0 DB E0 1F E0 F0 1F x App E0 5D E0 DD E0 2F E0 F0 2F Notes: 1. * Scan codes differ by mode. 2. * Sca[...]

Table D-2 Scan codes with left Shift key Code set 1 Code set 2 Cap No. Key top Make Break Make Break 55 / E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12 75 INS E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0 12 76 DEL E0 AA E0 53 E0 D3 E0 2A E0 F0 12 E0 71 E0 F0 71 E0 12 79  E0 AA E0 4B E0 CB E0 2A E0 F0 12 E0 6B E0 F0 6B E0 12 80 H[...]

Table D-3 Scan codes in Numlock mode Code set 1 Code set 2 Cap No. Key top Make Break Make Break 75 INS E0 2A E0 52 E0 D2 E0 AA E0 12 E0 70 E0 F0 70 E0 F0 12 76 DEL E0 2A E0 53 E0 D3 E0 AA E0 12 E0 71 E0 F0 71 E0 F 0 12 79  E0 2A E0 4B E0 CB E0 AA E0 12 E0 6B E0 F0 6B E0 F0 12 80 Home E0 2A E0 47 E0 C7 E0 AA E0 12 E0 6C E0 F0 6C E0 F0 12 81 E[...]

Table D-5 Scan codes in overlay mode Code set 1 Code set 2 Cap No. Keytop Make Break Make Break 09 8 (8) 48 C8 75 F0 75 10 9 (9) 49 C9 7D F0 7D 11 0 (*) 37 B7 7C F0 7C 23 U (4) 4B CB 6B F0 6B 24 I (5) 4C CC 73 F0 73 25 O (6) 4D CD 74 F0 74 26 P (–) 4A CA 7B F0 7B 37 J (1) 4F CF 69 F0 69 38 K (2) 50 D0 72 F0 72 39 L (3) 51 D1 7A F0 7A 40 ; (+) 4E [...]

D-8 [CONFIDENTIAL] Satellite A500D/Pro A500D Series Maintenance Manual Table D-7 No.126 key scan code Code set 1 Code set 2 Key top Shift Make Make Pause Common E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14 F0 77 Ctrl E0 46 E0 C6 E0 7E E0 F0 7E *: This key generates only make codes.[...]

Appendix E Key Layout 1. United Status (US) K e yboard Figure US keyboard 2. T raditional Chinese (CH) K e yboard Figur e CH keyboard 3. Thai (TI) K eyboard[...]

Figur e TI keyboar d 4 . Ko re a n (KO ) Key b o a rd Figur e KO keyboard 5. United Kingdom (UK) K eyboard[...]

Figur e UK keyboard 6. US International (UI) K eyboard Figur e UI keyboard 7. Hebrew (HB) K e yboard[...]

Figur e HB keyboard 8. Danish (DM) K eyboard Figur e DM keyboard 9. Swiss (S W) Ke yboard[...]

Figur e SW keyboar d 10. Arabic (ARE) K eyboard Figur e ARE keyboar d 11. Czec h (CZ) K eyboard[...]

Figur e CZ keyboard 12. Russian (RU) K e yboard Figur e RU keyboard 13. Por tuguese (PO) K eyboard[...]

Figur e PO keyboard 14. Slovakian (SL) K e yboard Figur e SL keyboar d 15. It alian (IT) K e yboard[...]

Figur e IT keyboar d 16. F rench (FR) K eyboard Figur e FR keyboard 17. German (GR) K eyboard[...]

Figur e GR keyboard 18. Greek (GK) K eyboard Figur e GK keyboard 19. Hungarian (HG) K eyboard[...]

Figur e HG keyboard 20. Spanish (SP) K eyboard Figur e SP keyboar d 21. T urkish (TR) K eyboard[...]

Figur e TR d 22. T urkish F (TF-F) K eyboard keyboar Figur e TF-F keyboard 23. Swedish (SD) K e yboard[...]

Figur e SD keyboard 24. Belgian (BE) K eyboard Figur e BE keyboard 25. Y ugoslavian (YU) K eyboard[...]

Figur e YU keyboar d 26. Nor w egian (NW) K eyboard Figur e NW keyboar d 2 7 . Scandinavian (ND) K eyboard[...]

Figur e ND keyboard 28. Canadian Multinational (A C) Ke yboard Figur e AC keyboar d 29. Canadian Bilingu al (CB) K eyboard[...]

Figur e CB keyboard 30. R omania (R O) K eyboard Figur e RO keyboard 31 . Bulgaria (BU) K e yboard[...]

Figur e BU keyboard 32. Japanese (JP) K eyboard Figur e JP eyboar d k[...]

DISCRIP TION Torque (kg-cm) Part number Q’ty LCD PANEL TO LCD BREAKET(H/L) 1.2~1.5 MA0000060G0 6 LCD HINGE TO LCD COVER(H) 2.5~3.0 MA000007JG0 8 LCD HINGE TO LCD COVER(L) 2.5~3.0 MA000007JG0 6 LCD BEZEL TO LCD BRK TO LCD COVER(H) 2.5~3.0 MA0000062G0 2 LCD BEZEL TO LCD BRK TO LCD COVER(L) 2.5~3.0 MA0000062G0 4 INVERTER TO LCD COVER 1.5~2.0 MA00000[...]

DISCRIP TION Torque (kg-cm) Part number Q’ty KEYBOARD TO LOGIC 1.5~2.0 MA0000060G0 4 KEYBOARD COVER TO LOGIC 1.5~2.0 MACA25001G0 2 SYSTEM LED BOARD TO LOGIC 2.5~3.0 MA000007JG0 1 L USB BOARD TO LOGIC 2.5~3.0 MA000007JG0 1 MB TO LOGIC 2.5~3.0 MA000005WG0 1 LOW BATTERY HOUSING TO UPPER 2.5~3.0 MA000007JG0 2 TV TUNER CABLER 2.5~3.0 MA000007JG0 1 CPU[...]

Appendix G Appendix G Reliability The followin g table shows MT BF (Mean Tim e Between Failures) for each com ponent. Table G-1 MTBF Component Time (hours) LCD 10,000 Keyboard 60,000 HDD 300,000 Optical (DVD/CD) drive 60,000 AC adaptor 60,000 Satellite A500D/Pro A500D Se ries Ma intenance Manual [CONFIDENTIAL] G-1[...]