Toshiba PSLD8U08201E manuale d’uso

GMAD00163011 07/08 If you need assistance: ❖ T oshiba’ s Support W eb site pcsupport.toshiba.com ❖ T oshiba Customer Support Center Calling within the United States (800) 457 -7777 Calling from outside the United States (949) 859 -4273 For more in formation, see “If Something Goes Wrong” on page 147 in this gui de. Satellite ® L350 Serie[...]

2 5.375 x 8.375 ver 2.3 Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling . Model: Satellite ® L350 Series Recordable and/or ReWritable Drive(s) and Associated Software W arranty The computer system you purchased may in[...]

3 5.375 x 8.375 ver 2.3 Critical Applications The computer you have purchased is not designed for any “critical applications. ” “Critical applications” means life s upport sy stems, medical applications, connections to implanted medi cal devi ces, commercial transportation, nuclear facilities or systems or an y other applicatio ns where pro[...]

4 5.375 x 8.375 ver 2.3 This device complies with P art 15 of the FCC Rules. Operation is subject to the following tw o conditions: ❖ This device may not cause harmful interference. ❖ This device must accept an y interferen ce received, including interference that may cause undesired operatio n. Contact either: ❖ T oshiba’ s Support W eb si[...]

5 5.375 x 8.375 ver 2.3 Connection to party line service is subject to state tarif fs. Contact the state public utility commission, public se rvice co mmission or corpor ation commission for information. T elephone Company Procedures The goal of the telephone company is to pro vide you with the best service it can. In order to do this, it may occas[...]

6 5.375 x 8.375 ver 2.3 Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable yo ur alarm equipment. If you hav e questions abou t what will disable alarm equipment, consult your telephone compan y or a qualified installer . Instructions for IC CS[...]

7 5.375 x 8.375 ver 2.3 Wireless Interoperability The TOSHIB A W ireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology , and is compliant to: ❖ The IEEE 802.11 Standard on W ireless LANs (Rev ision A/B/G), as defined and approv ed [...]

8 5.375 x 8.375 ver 2.3 In some situations or en vironments, the use of W ireless LAN may be restricted by the proprietor of the b uilding or responsible representativ es of the organization. These situatio ns may for e xample include: ❖ Using the W ireless LAN equipment on board airplanes, or ❖ In any other en vironment where the risk of inter[...]

9 5.375 x 8.375 ver 2.3 The term “IC” before the equipment certif ication number only signifies that the Industry Canada technical specifications were met. T o prev ent radio interference to the licensed service, this device is intended to be operated indoors an d away from windo ws to pr ovide maximum shielding. Equipment (or its transmit ante[...]

10 5.375 x 8.375 ver 2.3 The European Union WEEE (W as te from Electrical and Electronic Equipment) Directive Information The European Union WEEE (W aste from Electrical and Electronic Equipment) Directiv e is intended to protect the quality of the en vironment and human health through the responsible use of n atura l resources and the adoption of [...]

11 5.375 x 8.375 ver 2.3 Howe ver , due to dif ferences between the indi vidual PSTNs provided in dif ferent countries/re gions the approv al does not, of itself, gi ve an unconditional assurance of successful operation on ev er y PSTN network termination point. In the ev ent of problems, y ou should contact your equi pment supplier in the first in[...]

12 5.375 x 8.375 ver 2.3 2. Indication The indication shown belo w appears on this equipment. 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 DS: This equipment uses DS-SS modulation. O F: This equipment uses OFDM modulation. 3 The interference range of this equipment is less than 40m. 4 This equipment uses a frequenc y bandwidth from 2,400 MH[...]

13 5.375 x 8.375 ver 2.3 Radio Approvals for Wireless Devices The following information is de pendent on what type of wi reless de vice is in your computer . Not all devices are avai lable on all models. Approved Countries/Regions for use for the Atheros AR5BXB72 2.4 + 5GHz 11n minicard This equipment is approv ed to the radio standard by the count[...]

14 5.375 x 8.375 ver 2.3 Europe - Restrictions for us e of 2.4 GHz Frequencies in European Community Countries België/ Belgique: For pri vate usage outside b uildings acr oss public grounds over less than 300m no special registration with IBPT/BIPT is required. Registration to IBPT/BIPT is required for priv ate us age outside b uildings across pub[...]

15 5.375 x 8.375 ver 2.3 Europe - Restrictions for Use of 5 GHz Frequencies in European Community Countries O: allowed x: forbidden ❖ T o remain in conformance with Euro pean spectrum usage laws for Wireless LAN operation, the above 2.4 GHz and 5 GHz channel limitations apply . The user should use the wireless LAN utility to check the current cha[...]

16 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use for the Atheros AR5BXB63 11g minicard This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. This device works on passive scan only. A peer -to-peer mode is not ava[...]

17 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Realtek ® RTL8187B This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table. Albania Argentina Australia Austria Azerbaijan Bahrain Bangladesh Belgium Bolivia Bosni[...]

18 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use for the Intel ® PRO/Wireless 3945ABG Network Connection This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table. An adhoc mode is available in Ch1- Ch11(802.11b/g)[...]

19 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Intel ® Wireless Wi-Fi ® Link 4965AGN This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table. An adhoc mode is available in Ch1- Ch11(802.11b/g), An Infrastructu[...]

20 5.375 x 8.375 ver 2.3 Bluetooth ® Wireless T echnolo gy Interoperability Bluetooth ® Cards from TOSHIB A are designed to be interoperable with an y product with Bluetooth wireless technology that is based on Freque ncy Hopping Spread Spectrum (FHSS) radio t echnology , and is compliant to: ❖ Bluetooth Specification as def ined and approv ed [...]

21 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use ( Bluetooth ® wireless technology) Bluetooth ® Card from T oshiba equipment is ap proved to the radio standard by the countries/regions in the follo wing table. Do not use this equipment except in th e countries/regions in the follow ing table. Bluetooth ® Wireless T echnology and Y our[...]

22 5.375 x 8.375 ver 2.3 In some situatio ns or en vironments, the use of Bluetooth wireless technology may be restricted by the proprietor of th e building or responsible representati ves of the organization. These situations may for example include: ❖ Using the equipment with Bluetooth wireless technology on boar d airplanes, or ❖ In any othe[...]

23 5.375 x 8.375 ver 2.3 Ta i w a n The legal communications mentioned in the abov e item refer to radio communications operated in accordan ce with telecommunication laws and regulations. Lo w power radio frequency electric machin ery shall resist ag ainst interference from legal communications or from industrial, scientific and medical radio emis[...]

24 5.375 x 8.375 ver 2.3 2. Indication The indication shown belo w appears on this equipment. 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 FH: This equipment uses FH-SS modulation. 3 The interference range of this equipment is less than 10m. 4 This equipment uses a frequenc y bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to av o[...]

25 5.375 x 8.375 ver 2.3 Optical Drive Safety Instructions This appliance contains a laser syst em and is classified as a CLASS 1 LASER PRODUCT . T o use this model properl y , read th e user’ s guide carefully and keep it for your fut ure reference. Never attempt to disass emble, adjust or repair an opti cal drive. Y ou could damage the drive. Y[...]

26 5.375 x 8.375 ver 2.3 Export Administration Regulation This document contains technical data that may be controlled under the U.S. Export Administration Regulations, and ma y be subject to the approval of the U.S. Department of Commerce prior to expor t. Any export, directly or indirectly , in contrav ention of the U.S. Export Ad ministration Re[...]

27 5.375 x 8.375 ver 2.3 T rademarks Satellite and ConfigFree are re gistered trademarks of T oshiba Ameri ca Information Systems, Inc. and/or T oshiba Corporation. Microsoft, Outlook, Windo ws, and Wi ndo ws V ista are either registered trademarks or trademarks of Microsoft Corporatio n in the United States and/or other countries. DirectX, Activ e[...]

28 5.375 x 8.375 v er 2.3 Contents Introduction ................ ................................................................ 35 This guide ...............................................................37 Safety icons ............................................................38 Other icons used ...............................................[...]

29 Contents 5.375 x 8.375 v er 2.3 Charging the main battery ....................................... 48 Using the computer for the first time ......................49 Opening the display panel .................................49 Your computer’s features and specifications ....50 Turning on the power ........................................50 Addi[...]

30 Contents 5.375 x 8.375 v er 2.3 Chapter 2: Learning the Ba sics ................................................. 78 Computing tips ....................................................... 78 Using the keyboard .................................................80 Character keys .................................................. 80 Ctrl, Fn, and Al[...]

31 Contents 5.375 x 8.375 v er 2.3 Charging the RTC battery .................................. 97 Monitoring main battery power ............................... 98 Determining remaining battery power ............... 99 What to do when the main battery runs low ...100 Setting battery notifications ............................100 Conserving battery po[...]

32 Contents 5.375 x 8.375 v er 2.3 Using an ExpressCard ® .........................................122 Inserting an ExpressCard ® ..............................122 Removing an ExpressCard ® ............................122 Using the Bridge Media Adapter Slot ....................123 Inserting memory media ................................. 123 Remo[...]

33 Contents 5.375 x 8.375 v er 2.3 The Windows ® operating system can help you .................................................... 153 Resolving a hardware conflict ...............................153 A plan of action ...............................................153 Fixing a problem with Device Manager ...........154 Memory problems ............[...]

34 Contents 5.375 x 8.375 v er 2.3 Sleep mode .....................................................185 Hibernation mode ........................................... 186 Output (Display switch) ..................................187 Display brightness .......................................... 188 Disabling or enabling wireless devices............189 [...]

35 5.375 x 8.375 ver 2.3 I n t roduct ion W elcome to the world of powerful, portable, multimedia computing. W ith your T osh iba computer , your work and entertainment can accompan y you where ver you go. Y our Computer model may be ENERGY ST AR ® compliant. If the model you purchased is compliant, it is labeled with the ENER GY ST AR ® log o on[...]

36 Introd uctio n 5.375 x 8.375 ver 2.3 According to the EP A, a computer meeting the new ENERGY ST AR ® specifications will use between 20% and 50% less energ y depending on how it is used. If all U.S. household and businesses replaced old computers with ne w ENERGY ST AR ® qualified models, we would sav e more than $1.8 billion in energy costs [...]

37 Introduction This guide 5.375 x 8.375 ver 2.3 The product specifications and configuration i nformation are designed for a product Series. Y our particular model may not have all the features and specifications listed or illustrat ed. For more detailed information about the features and spec ifications on your particular model, please visit T os[...]

38 Introd uctio n Safety icons 5.375 x 8.375 ver 2.3 Safety icons This manual contains safety inst ructions that must be observed to av oid potential hazards that co uld result in personal injuries, damage to your equipment, or loss of data. These safety cautions hav e been classif ied according to the seriousness of the risk, and icons highlight t[...]

39 Introduction Other documentation 5.375 x 8.375 ver 2.3 Other documentation Y our computer comes with the following documentation: ❖ An electronic version of the user’ s guide (this docum ent) ❖ It may also contain guides for other programs that may come with your system. For accessory information, visit T oshiba’ s W eb site at accessori[...]

40 Chapter 1 Getting Started This chapter provides tips for us ing your computer ef fecti vely , summarizes how to connect components, and explains what to do the first time you use your computer . The “Instruction Manual for Safet y and Comfort, ” that is shipped with your computer, contains impo rtant safety information. Please read the safet[...]

41 Getting Started Selecting a place to work T o keep your computer in prime operating condition, protect you r work area from: ❖ Dust, moisture, and direct sunlig ht. ❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones. ❖ Rapid changes in[...]

42 Getting Started Selecting a place to work ❖ Avoid prolonged physical contact with the underside or s urface of the computer . ❖ Computer base and palm rest can become hot! Avoid prolonged contact to prevent heat injur y to skin. Read the “ A void Extended cont act between computer base/palm rest and skin” section in the “Instruction Ma[...]

43 Getting Started Setting up your computer Important information on your computer’ s cooling fan Y our computer may have a CPU cooling fan that coo ls the CPU by drawing outside air into the computer . Always mak e sure your compute r and AC adapt or have adequate ventilation and are protected from overheating when the power is turne d on or whe[...]

44 Getting Started Setting up your computer Please handle your computer carefully to avo id scratching or damaging the surface. Setting up your software When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely . The names o f windows displaye d, and the order in which windows[...]

45 Getting Started Re gistering your computer with T oshib a Registering your computer with T oshiba Product registration is strongly reco mmended, and allows T oshiba to send you periodic updates, announcement s, and special offers applicable to your p roduct. Product registration can be completed by either visiting the T oshiba W eb site at http:[...]

46 Getting Started Connecting to a power so ur ce Connecting to a power source Y our computer requires power to operate. Use the po wer cord/cable and A C adaptor to connect the comput er to a liv e electrical outlet, or to charge the computer’ s battery . Never pull on a power cord/cable to remove a plug from a socket. Always grasp the plug dire[...]

47 Getting Started Connecting to a po wer sour ce T o connect A C power to the computer: 1 Connect the po wer cord/cable to the A C adaptor . (Sample Illustration) Connecting the power cord/cable to the A C adaptor Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other [...]

48 Getting Started Char ging the main battery The computer’ s main battery light gives you an indication of the main battery’ s current char ge: ❖ Glows amber while the main battery is bei ng charged (A C adaptor connected) ❖ Glows green when the main battery is f ully charged ❖ Is unlit when t he main battery has d ischarged, the battery[...]

49 Getting Started Using the computer for the f irst time Battery life and charge time may var y depending on the applications, power management settings, and features used. Using the computer for the first time The computer is now ready for you to turn it on and be gin using it. Opening the display panel 1 Facing the front of the com puter, locate[...]

50 Getting Started Using the computer for the fir st time Small bright dots ma y appear on your screen displa y when you turn on your computer . Y our disp lay contains an extremely large number of thin-film transistors (TFT) and is manufactured using high- precision technology . An y small bright dots that may appear on your display are an intrins[...]

51 Getting Started Adding memory (optional) 3 Press and release the power button. The on/off light glo ws green. (Sample Illustration) T urning on the power The preinstalled operating syst em will load automatically . When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely .[...]

52 Getting Started Adding memory (optional) Installing a memory module Memory modules can be installed in the memor y module slots on the base of the computer . Y ou will need a small Phillips scr e wdriver for this procedure. If the computer has been running recently , the memory module may be hot. The surrounding area may also be hot. Allow the m[...]

53 Getting Started Adding memory (optional) If the computer is on, begin at step 1 ; otherwise, skip t o step 3 . 1 Click Start , and then click the arrow ne xt to the lock button in the lower -right corner of the Start men u. The Shut Down menu appears. (Sample Image) Shut Down menu 2 Click Shut Down . The operating system turns off the computer .[...]

54 Getting Started Adding memory (optional) 6 Using a small Phillips screwdri ver , loosen the capti ve scre w that secures the memory module slot cover . (Sample Illustration) Removing the memory module slot cover 7 Remove the memory module slot cov er . 8 Place the screw and the cov er in a safe place so that you can retriev e them later . Static[...]

55 Getting Started Adding memory (optional) If your system has the memory modules stacked on top of one another , you must remove the top module first before removing/installing the bottom module. For this model Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in Slot A. 11 Pick u[...]

56 Getting Started Adding memory (optional) 13 Once the module’ s connector is fu lly inserted into the socket, press downw ard on the top edge of the module to seat the module into the latches at the sides of the so cket. These latches should “snap” into place securely with th e corresponding cutouts in the side of the module. If the latches[...]

57 Getting Started Adding memory (optional) 14 Replace the memory modu le slot cov er and secure it using the screw . 15 Re-insert the main battery . For more information on inserting the main battery , see “Inserting a char ged battery” on page 106 . 16 T urn the computer right side up. 17 Reconnect the cables. 18 Restart the computer . TECHNI[...]

58 Getting Started Adding memory (optional) The following screen may appear when you turn on the power: If “Start Windows ® Normally” is highlighted, then press Enter . If one of the Safe Mode options is highlighted, it is best to press Enter to go into Safe Mode, then shut down and restart the system, at which time Windows ® should boot back[...]

59 Getting Started Adding memory (optional) 4 Replace the memory modu le slot cov er and secure it using the screw . 5 Re-insert the main battery . For more information on inserting the main battery , see “Inserting a char ged battery” on page 106 . 6 T urn the computer right side up. 7 Reconnect the cables. 8 Restart the computer . TECHNICAL N[...]

60 Getting Started Using the T ouchP ad™ Using the T ouchPad ™ The T ouchPad ™ , the small, rectangular area located in front of the keyboard, is sensiti ve to touch and enables you to move the cursor with the stroke of a f inger . Simply mov e your finger on the T o uchPad in the direction you would like to move the cursor: ❖ T o mov e the[...]

61 Getting Started Using external display de vices Disabling or enabling the T ouchPad ™ The T ouchPad ™ is enabled by default. T o change the enable/disable T o uchPad setting, press Fn + F9 . This hot k ey enables/disables the T o uchPad. For more information, see “Disabli ng or enabling the T o uchPad™” on page 190 . Using external dis[...]

62 Getting Started Using external display de vices 2 While holding down Fn , press F5 repeatedly until the setting you want takes ef fect. Briefly pause each time you press the F5 ke y to allow time for the display to change. This hot key c ycles through the settings in the fo llo wing order (the last two options are a v aila ble if an external mon[...]

63 Getting Started Using an external k e yboard Using an external keyboard If you prefer to use a full-size k e yboard, you can attach one to you r computer . The computer’ s US B ports support most USB- compatible ke yboards. Using a mouse Y ou may want to use a mouse instead of the computer’ s built-in T o uchPad. Y ou can use a USB-compatibl[...]

64 Getting Started Connecting an option al external diskette drive Setting up a printer Some printers require a specific installation process. Refer to your printer installation guide for instructions before completing the following procedure. If your printer does not support Plug and Play , follo w these steps to set it up for the first time. Y ou[...]

65 Getting Started T urning off the computer T o connect an optional external USB disk ette driv e, connect the cable to one of the comput er’ s USB ports. (Sample Illustration) Connecting a n optional external USB diskette drive T urning off the computer Pressing the power button before shutting down the Windows ® operating system could cause y[...]

66 Getting Started T urning off the computer TECHNICAL NOTE: Before using the Shut Down option to turn off your computer , save your files and make sure all disk/dis c activity lights are off. If you change your mind and decide to continue working after all, wait a few seconds before turning the computer on again. ❖ Use the Sleep command to save [...]

67 Getting Started T urning off the computer Sleep mode The Sleep command places the comput er into a power -saving mode. Sleep sa ves the current state of the computer to memory so that, when you restart the comp uter , you can continue working from where you left of f. After your computer sleeps for an extended period of time, the Windows ® oper[...]

68 Getting Started T urning off the computer Using the Shut Down command The Shut do wn command complet ely shuts down the computer without saving your work or the cu rrent state of th e computer . This command closes all open program s, shuts down the operating system, and then turns off your computer . Use the following steps to turn of f your co[...]

69 Getting Started T urning off the computer 3 Click Change advanced power settings . The Advanced settings tab of the Po wer Options window appears. (Sample Image) Advanced settings tab of P ower Options scr een 4 Click Power buttons and lid to display the actions that you can configure. 5 Select the options you want from the drop-down lists. Thes[...]

70 Getting Started T urning off the computer 6 Click App l y . 7 Click OK . Once the computer is conf igured, you can turn it off b y either pressing the power b utton or closing the display panel, depending on the options set . Restarting your computer T o start the computer up again, press the po wer b utton unti l the on/off light glows green. I[...]

71 Getting Started T urning off the computer Configuring Hibernation mode options Y ou can place the computer into Hibernation mode by either pressing the power b utton or closing the display panel. Y ou can also specify an amount of time after which the computer automatically goes into Hibernation mode. T o use any of these methods, you f irst nee[...]

72 Getting Started T urning off the computer 4 Click Power buttons and lid to display the actions that you can configure. 5 Select Hibernate for the options you want. These options can be set separately for how they operate while the computer is running on battery power or while connected to AC power . ❖ Lid close action Set this option to Hibern[...]

73 Getting Started T urning off the computer Using and configuring Sleep mode T o turn off the com puter using the Sleep command: 1 Click Start , and then click the arro w ne xt to the Lock button in the lower -right part of the Start menu. The Shut Down menu appears. (Sample Image) Shut Down menu 2 Click Sleep . The computer sa ves the status of a[...]

74 Getting Started T urning off the computer 2 Click Change pl an settings under the power plan to be customized. The Edit Plan Settin gs window appears. (Sample Image) Edit Plan Settings screen 3 T o change the amount of time af ter which the computer enters Sleep mode: ❖ Under Put the computer to sleep , select the desired amount of time in bot[...]

75 Getting Started T urning off the computer 5 Click Power buttons and lid to display the actions that you can configure. 6 Select Sleep for the options you want. These options can be set separately for how they operate while the computer is running on battery power or while connected to AC power . ❖ Lid close action Set this option to Sleep if y[...]

76 Getting Started Customizing your comp uter’ s settings Customizing your computer’ s settings There are sev eral ways in which you can customize your computer to suit your particular req uirements. Refer to your operat ing system documentation or Help and Su pport for details. Y ou may also wish to customize your power usage settings. F or mo[...]

77 Getting Started Caring for your computer Using a computer lock Y ou may want to secure your comput er to a heavy object such as your desk. The easiest way to do this is to purchase an optional computer lock cable. For more information on purchasing a cable lock, visit accessories.toshiba.com . (Sample Illustration) Computer lock cable T o secure[...]

78 Chapter 2 Learning t he Basics This chapter giv es some computing tips and provides important information about basic features. Computing tips ❖ Sav e your work frequently . Y our work stays in the computer’ s temporary memory until you sav e it to the internal storage drive. If the netw ork you are using goes down and you must restart your [...]

79 Learning the Basics Computing tips ❖ Back up your files to disks (or other remov able media) on a regular basis. Label the backup co pies clearly and store them in a safe place. It is easy to put of f backing up because it takes time. Ho wev er , if your internal storage drive suddenly fails, you will lose all the data on it unless you hav e a[...]

80 Learning the Basics Using the ke yboar d Using the keyboard Y our computer’ s ke yboard contai ns character keys, control ke ys, function ke ys, and special W indo ws ® k eys. (Sample Illustration) Ke yboar d Character keys T y ping with the character keys is very much like typing on a typewriter , e xcept that: ❖ The space bar creates a sp[...]

81 Learning the Basics Starting a pr ogr am Function keys The function k eys (not t o be confused with the Fn key) are the 12 keys at the top of the k eyboard. (Sample Illustration) Function ke ys F1 through F12 are called function keys because the y ex ecute programmed functions when pressed. Used in combin ation with the Fn key , fun ction keys m[...]

82 Learning the Basics Starting a pr ogram Starting a program from the Start menu When you install a prog ram, the operating syst em usually puts an icon in the Al l Programs menu. T o start a progr am that has an icon in the All Programs menu, follow these steps, which use the W indows ® W ordPad program as an example: 1 Click Start , and then Al[...]

83 Learning the Basics Starting a pr ogr am 5 In the left part of the window , c lick the line that ends in “Local Disk (C:). ” 6 In the left part of the window , under the Local Disk C: icon, double-click the folder contai ning the program, in this case Program Files . W indows ® Explorer shows the contents of the Program Files folder on the [...]

84 Learning the Basics Saving your work Saving your work Before you turn off the computer using the Shut Down command, sav e your work on the internal storage driv e, diskette, flash media, or optical disc. This is one of the most important rules of computing. When you turn of f the computer using the Sleep or Hibernate commands, your work should b[...]

85 Learning the Basics Printing your work HINT : T o make another copy of the file you are currently working with, click File , and then Save As , and give the new file a different name. File names The W indo ws ® operating system supp orts long file names that can contain up to 260 characters and can include spaces. Some applications do not suppo[...]

86 Learning the Basics Backing up your work 2 In your W indows ® -based application, click File , and then Print . The program displays a Print dialog box. (Sample Image) Print dialog box 3 Specify the print parameters. For e xample, the range of pages and number of copies to print. 4 Click Print . Backing up your work Back up all the files you cr[...]

87 Learning the Basics Using the optical drive Restoring your work T o restore information from your backu p media to your internal storage dri ve, use the Restore page in the backup program. Look in the online Help or your op erating system documentation for information on restoring files. TECHNICAL NOTE: When restoring files, the backup program p[...]

88 Learning the Basics Using the optical drive When viewing DVD movies use the DVD Player software that came with your computer . Optical drive components The optical dri ve is located on the side of the computer . Y our optical drive may look like this: (Sample Illustration) Optical drive Drive in-use indicator light —Indicates when the driv e i[...]

89 Learning the Basics Using the optical drive Media control buttons (A vailable on certain models) The media control buttons located on the system control panel above the keyboard let you mute the sound and play audio CDs or D VD movies when the computer is on. (Sample Illustration) Media contr ol buttons The Mute b utton allo ws you to mute the s[...]

90 Learning the Basics Using the optical drive 4 Grasp the tray and pull it fully open. (Sample Illustration) Drive tray fully extended 5 Hold the disc by its edges and check that it is free of dust. If the disc is dusty , clean it as described in “Caring for optical discs” on page 93 . 6 Place the disc carefully in th e disc tray , label side [...]

91 Learning the Basics Using the optical drive If you insert the disc incorrectly , it may jam the drive. If this happens, contact T oshiba support for assistance. 9 Push the disc tray in by pressing gently on the center of the tray until it clicks into place. Y ou are ready to use the disc. Playing an audio CD Insert an audio CD and close the disc[...]

92 Learning the Basics Using the optical drive For more information regarding supported optical media formats please refer to your computer’ s detailed specif ications at pcsupport.toshiba.com . Due to manufacturing and quality variations in third party optical media (e.g., CD or DVD) or optical media players/recorders, in certain cases, your T o[...]

93 Learning the Basics T oshiba’ s online r esour ces Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it. 2 Pull the tray out until it is fully open , remove the disc, and place it in its protecti ve co ver . 3 Gently press the tray in to close it. Caring for optical discs ❖ Store yo[...]

94 Chapter 3 Mobile Computing This chapter cov ers all aspects of using your com puter while trav eling. T oshiba’ s energy-saver design Y our computer enters a low-po wer suspension mode when it is not being used, thereby conserving energy and sa ving money in the process. It has a number of other features that enhanc e its energy ef ficiency . [...]

95 Mobile Computing Running the computer on battery power Battery Notice Battery life may vary considerably from specif ications depending on product model, configuration, applications, power management settings and features utilized, as well as th e natural performance variations produced by the design of indi vidual components. Published battery [...]

96 Mobile Computing Char gi ng batteries Power management Y our computer ships with t he power management options preset to a configuration that will prov ide the most stable opera ting en vironment and optimum system performan ce for both A C power and battery modes. Changes to these settings may result in system performance or stability issues. U[...]

97 Mobile Computing Char ging ba tteries Charging the main battery T o charge the main battery while it is in your computer, plug the computer into a li ve electrical ou tlet. The battery char ges whether the computer is on or off. TECHNICAL NOTE: The rech arging of the batter y cannot occur when your computer is using all of the pow er provided by[...]

98 Mobile Computing Monitoring main battery power If the R TC battery is lo w , the real-time clock and calendar may display the incorrect tim e and date, or stop working. T o recharge the R TC battery , plug the computer into a li v e electrical outlet and leav e the computer powered on for 24 hours. It is seldom necessary to charge the RTC batter[...]

99 Mobile Computing Monitoring main battery power HINT : Be careful not to confuse the battery light ( ) with the on/off light ( ). When the on/off light flashes amber , it indicates that the system is suspended (using the Windows ® operating system Sleep command). (Sample Illustration) P ower and batt ery light locations Determining remaining bat[...]

100 Mobile Computing Monitoring main battery power Highlight the power icon in the Notification Area. A pop-up message displays the remaining battery power as a percentage. W ith repeated discharges and rechar ges, the battery’ s capacity gradually decreases. A frequently us ed older batt ery does not power the computer for as long as a new batte[...]

101 Mobile Computing Monitoring main battery power T o change the default notification settings: 1 Click Start , Contro l Panel , Mobile PC , and th en Power Options . The Po wer Options window appears. 2 Click Change plan s ettings under the po wer plan to be customized. The Edit Plan Settin gs window appears. 3 Click Change advanced power setting[...]

102 Mobile Computing Monitoring main battery power There are v arious ways in which you can conserv e power and extend the operating time of your battery: ❖ Enable Sleep or Hibernation, which saves po wer when you turn of f the computer and turn it back on again ❖ Use the W indows ® po wer-saving option plans These power -saving options contro[...]

103 Mobile Computing Monitoring main battery power T o edit a plan or to edit advanced settings, continue to the following steps. 4 Click Change Plan Se ttings to choose the plan you want to edit. This screen allows you to change basic settings. 5 Click Change Adv anced Settings to access settings for battery notification lev els, inte rnal storage[...]

104 Mobile Computing Changing the main battery 2 While continuing to press Fn , press F2 until you select the desired Power Plan. The Po wer Plan options are: Balanced, Po wer Sav er , and High Performance. 3 Release the Fn key . The hot ke y card disappears. Y ou are now in the selected mode. Changing the main batter y When your main battery has r[...]

105 Mobile Computing Changing the main battery 5 Slide the battery release lock to the unlo cked position. (Sample Illustration) Unlocking the battery r elease lock 6 Slide the battery release latch to release the battery . 7 Pull the discharged battery out of the computer . (Sample Illustration) Removing the battery If the battery is leaking or it[...]

106 Mobile Computing Changing the main battery Inserting a charged battery T o insert a battery: 1 W ipe the terminals of the charge d battery with a clean cloth to ensure a good connection. 2 Insert the charged battery into the slot until the latch clicks. The battery pack has been designe d so that you cannot install i t with rev erse polarity . [...]

107 Mobile Computing T aking car e of your battery 4 T urn the computer right side up. 5 Reconnect any cables that were remov ed in step 3 of “Removing the battery from the computer” on page 104 . 6 Restart the computer . T aking care of your batter y The follo wing sections offer tips on how to take care of your battery and prolong its life. S[...]

108 Mobile Computing T aking car e of your battery Maintaining your batter y Fully discharging your battery pack will allo w better accurac y of the battery meter . T o fully discharge your battery pack: ❖ Periodically , disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doi[...]

109 Mobile Computing Disposing of used batteries Disposing of used batteries The life of a battery pack depends on usage. When the battery pack needs replacing, the main batt ery light flashes amber shortly after you hav e fully recharged the battery . Y ou m ust discard a batter y if it becomes damaged. Never attempt to dispose of a battery pack b[...]

110 Mobile Computing T raveling tips T o shiba is dedicated to preservi ng the en vironment by sponsoring Call2Recycle™ , a program of the Rechar geable Battery Recycling Cor por atio n. For more information and for drop-of f locations, visit www .rbrc.org or call 1-800-822- 8837. Notice regarding CR coin ce ll batter ies, applicable to Californi[...]

111 Chapter 4 Exploring Y our Computer’ s Features In this chapter , you will explore some of the special features of your computer . Exploring the desktop The desktop is the launching pad for everything you can do in the W indows ® operating system. Y ou use its features to start programs, find documents, set up system components, and perform m[...]

112 Exploring Y our Computer’ s Features Explorin g the desktop Finding your way around the desktop Y our computer’ s desktop includes sev eral standard features: icons, Start button, T askb ar , Notification Area, and background pattern. (Sample Image) W indows ® operating system desktop Icons An icon represents a folder , file, or program th[...]

113 Exploring Y our Computer’ s Features Exploring the desktop Y our desktop may contain other icons depe nding on your configuration. See W indo ws ® online Help for more specific information on each icon and ho w to use it. Start button Y ou use the Start button to: ❖ Start programs ❖ Open documents ❖ Adjust system settings ❖ Find file[...]

114 Exploring Y our Computer’ s Features Setting up for communications Setting up for communications T o connect to the Internet, use an online service, or communicate across the telephone lines with another computer , you need: ❖ A browser or communications program ❖ An Internet Service Pro vider (ISP ) or online service if you plan to use t[...]

115 Exploring Y our Computer’ s Features Setting up for communications Accessing a network T o access a network: ❖ At the of fice, c onnect an Ethern et cable to the RJ45 jack on your computer . For specific info rmation about connecting to the network, consult your netw ork administrator . Many hotels, airports, and of fices of fer W i-Fi ® a[...]

116 Exploring Y our Computer’ s Features Setting up for communications For more detailed i nformation regarding your computer’ s modem, visit T oshiba’ s W eb site at accessories.toshiba.com . Before you can communicate using th e modem, you need to connect it to a telephone line. Y ou r computer’ s b uilt-in modem port provides an RJ-11 ja[...]

117 Exploring Y our Computer’ s Features An overview of using the Internet An overview of using the Internet The following sections giv e a quick introduction to t he Internet and some of its exciting featur es, under these headings: ❖ The Internet ❖ The W orld Wi de W eb ❖ Internet Service Providers ❖ Connecting to the Internet ❖ Surfi[...]

118 Exploring Y our Computer’ s Features An overview of using the Internet Connecting to the Internet T o connect to the Internet, you need: ❖ A modem and telephone line, or a LAN connection ❖ A W eb browser ❖ An Internet Service Provider (ISP) account Once you hav e established an ISP account, you can connect to the Internet. 1 Connect you[...]

119 Exploring Y our Computer’ s Features An overview of using the Internet Internet features The Internet offers man y types of communicati on tools to help you perform many tasks. ❖ Internet email T o send and recei ve email of your o wn, you need a mailbox on the W eb or an email address. If you hav e an account with an ISP , you can probably[...]

120 Exploring Y our Computer’ s Features Explor ing audio feat ur es Exploring audio features Y ou can use your computer to record sounds using the com puter’ s internal microphone (av ailable on certain models) or an opti onal external microphone. Y ou can listen to sound files or audio CDs using the b uilt-in speakers, headphones, or e xterna[...]

121 Exploring Y our Computer’ s Features We b C a m e r a TECHNICAL NOTE: When using amplified speakers, use speak ers that require an external power source. Other types of speakers will be inadequate to produce sound from the computer . T o play back sound files through e xternal speakers or headphones: 1 Locate the headphone jack on the compute[...]

122 Exploring Y our Computer’ s Features Using an Expr essCard ® Using an ExpressCard ® The ExpressCard ® slot supports the use of Ex pressCard media. The slot also supports ho t swapping, which allo ws you to replace one ExpressCard with another while the computer is on. Inserting an ExpressCard ® Before you insert an ExpressCard ® , refer [...]

123 Exploring Y our Computer’ s Features Using the Bridge Media Adapter Slot 4 Grasp the edges of the ExpressCar d and slide it out of the slot. (Sample Illustration) Removing an Expr essCar d Using the Bridge Media Adapter Slot (A vailable on certain models) The Bridge Media Adapter slot (av ailable on certain models) supports the use of Memory [...]

124 Exploring Y our Computer’ s Features Using the Bridge Media Adapter Slot 2 Push the media into the ad apter until it locks in place. (Sample Illustration) Inserting memory media When inserting memory media, do not touch the metal contacts. Y ou could expose the storage area to static electri city , which can destroy data. Removing memor y med[...]

125 Chapter 5 Utilities Y our computer includes sev eral utilities designed to help yo u to reconfigure your system to best meet your individual needs. T o gether , these allo w you to ascerta in certain system details, set additional options, or change default optio ns. These utilities are described in this chapter . The utilities described in thi[...]

126 Utilities TOSHIB A Assist TOSHIBA Assist The TOSHIB A Assist pro vides qui ck access to computer functions and allows you to customize a range of com puter settings. T o access TOSHIB A Assist, click Start , All Programs , To s h i b a , Utilities , and then TOSHIB A Assist . The TOSHIB A Assist windo w appears. (Sample Image) T OSHIBA Assist w[...]

127 Utilities TOSHIB A Assist Connect The features av ailable in this category are: ❖ ConfigFree ® Connectivity Doctor (Sample Image) T OSHIBA Assist window – Connect tab[...]

128 Utilities TOSHIB A Assist Secure The features av ailable in this category are: ❖ Supervisor password ❖ User password (Sample Image) T OSHIBA Assist window – Secur e tab[...]

129 Utilities TOSHIB A Assist Protect & Fix The features av ailable in this category are: ❖ TOSHIB A PC Diagnostic T ool Utility (Sample Image) T OSHIBA Assist window – Pr otect & Fi x tab[...]

130 Utilities TOSHIB A Assist Optimize The features av ailable in this category are: ❖ Mouse Utility ❖ TOSHIB A Hardware Se tup ❖ TOSHIB A Zooming Utilit y ❖ TOSHIB A Button Su pport ❖ CD/D VD Dri ve Acoustic Silencer ❖ TOSHIB A Accessibility (Sample Image) T OSHIBA Assist window – Optimize tab[...]

131 Utilities Setting passwor ds Setting passwords Setting a password lets you walk aw ay from your computer whi le providing additional protection for your files. When you set a password, you must enter the password before you can w ork on your computer again. T oshiba supports se ve ral types of passwords on you r computer: ❖ An instant passwor[...]

132 Utilities Setting passwor ds Using a supervisor password A supervisor password pre vents other users from changing hardware configuration options. Setting a supervisor password If you choose to set a supervisor or user password, T oshiba strongly recommends that you save your password in a location where you can later access it should you not r[...]

133 Utilities Setting passwor ds 6 Click OK . The supervisor password util ity dialog box appears. 7 Select Able to run HWSetup or Unable to run HWSetup and then Click OK . 8 Restart the system to complete the process. Deleting a supervisor password T o delete a supervisor passwor d: 1 Click Start , All Programs , To s h i b a , Utilit ies , and th[...]

134 Utilities Setting passwor ds T o register a password for the po wer- on password functions: 1 Click Start , All Programs , To s h i b a , Utilit ies , and then TOSHIB A Passw ord Utility . The TOSHIB A P assword Utility windo w appears. (Sample Image) TOSHIB A P asswor d Utility window 2 Click Registered . 3 Enter your pas sword, and then enter[...]

135 Utilities TOSHIB A PC Dia gnostic T ool Utility TOSHIBA PC Diagnostic T ool Utility This utility can h elp diagnose pro blems with devices in your computer . Refer to the online Help documentatio n within the application for additional help. The TOSHIBA PC Diagnostic T ool u tility may show tests for features you do not have. This is normal and[...]

136 Utilities Mouse Utility Mouse Utility The Mouse utility allows you to change your pointing device or mouse settings. T o access the Mouse utility: 1 Click Start , Contr ol Panel , and then Mouse under Hardwa re and Sound , or click the Mouse icon in the Optimize tab of TOS HI BA A ss is t . The Mouse Properties screen appears. (Sample Image) Mo[...]

137 Utilities TO S H I BA H a rd w a re S e t u p TOSHIBA Hardware Setup TOSHIB A Hardware Setup is the T oshiba con figuration management tool av ailable through th e W indows ® operating system. T o access it: ❖ Click Start , All Programs , To s h i b a , Utilit ies , and then HWSetup , or clic k the TOS HI BA H a rdw a re Se t up icon in the [...]

138 Utilities TO S H I BA H a rd w a re S e t u p ❖ CPU —Allows you to enable or disable CPU frequency switching modes Dynamically Swit chable —This mode is th e default setting for your computer , and automatica lly changes the processing frequency and decreases v oltage depending on the power source: ❖ AC P o w e r —If your computer is [...]

139 Utilities TOSHIB A Zooming Utility TOSHIBA Zooming Utility This utility allows you to select which applications will work with the zoom in/out hot ke ys (see “Zoom (Display resolu tion)” on page 191 ). Y ou may select all applications or any subset of the following: ❖ Microsoft ® Internet Explorer ® ❖ Microsoft ® Of f ice ❖ W indo [...]

140 Utilities TOSHIB A Button Support T o zoom in, hold down the Fn key and press 2 ; to zoom out, hold down the Fn ke y and press 1 . For more information about how to use the T OSHIBA Zooming Utility , right-click the icon in the Notification Area and then click Help . TOSHIBA Button Support (A vailable on certain models) TOSHIB A Button Support [...]

141 Utilities CD/D VD Drive Acousti c Silencer CD/DVD Drive Acoustic Silencer This utility can slow the speed of your optical driv e to make it run more quietly . Y ou can use this utility to m ake listening to music CDs more enjoyable. When you change the optical drive to “Silence” mode, the setting is only valid for the current Windows ® ses[...]

142 Utilities TOSHIB A Accessibility TOSHIBA Accessibility The TOSHIB A Accessibility utility allows you to use the Fn ke y to create a hot key combination wit h one of the function ke ys without pressing the two keys simultaneously as is usually required. Using Accessibility lets you make the Fn key a sti cky key , meaning you can press it once, r[...]

143 Utilities ConfigF r ee® ConfigFree ® All references to Bluetooth ® in this section are applicable only if Bluetooth ® is available on your system. ConfigFree ® is a set of utilities that makes it easy to control communication devices and networ k connections. Conf igFree also lets you identify communication problems and create profiles for[...]

144 Utilities ConfigF r ee® If your computer is not connected to a network, the ConfigFree icon in the Notification Area is displayed with an “X.” ConfigFree ® Utilities Connectivity Doctor The Connectivity Doctor lets you analyze your network connections and fix network connection prob lems. Using Connectivity Doctor , you can vie w detailed[...]

145 Utilities ConfigF r ee® Profile Settings The Prof ile Settings utility lets you save network settings in “profiles . ” ConfigFree ® prof iles are useful for easily switching network settings an d devices. Y ou can switch network settings simply by selecting the profile with the desired settings. If you visit a client company occasionally [...]

146 Utilities ConfigF r ee® 3 Click Open Settings . The ConfigFree Prof ile Settings windo w appears. (Sample Image) ConfigF ree Pr ofile Settings windo w 4 Click Add to start the Creat e Profile W i zard.[...]

147 Chapter 6 If Somet hing G oes W r o ng Some problems you may encounter wh en using your computer are relativ ely easy to identify and solve. Others may require help fro m your network administrator or the manufacturer of the software program. This chapter aims to help you solve many problems b y yourself. It cov ers the problems you are most li[...]

148 If Something Goes Wrong Pr oblems when you turn on the computer 2 Click the A pplications tab . If a program has stopped responding, the words “not responding” appear beside its name in the list. 3 Select the program you want to close, then click End T ask . Closing the failed prog ram should allow you to continue working. If it does not, c[...]

149 If Something Goes Wrong Pr oblems when you turn on the computer If you are using an A C adaptor , v e rify that the computer is recei ving power from the external po wer source by looking at the A C power light. If the indicator is glo wing, th e computer is connected to a liv e external po wer source. The computer starts but when y ou pr ess a[...]

150 If Something Goes Wrong Pr oblems when you turn on the computer If you are running on battery power , it is recommended that you do not leav e the computer in Sleep mode for long periods of time. T o charge the battery , leave the computer plugged into a liv e wall outlet for sev eral hours. For more information see “Charging batteries” on [...]

151 If Something Goes Wrong The W indo ws ® operating system is not working 5 V erify that the A C adaptor is th e correct unit for your computer model. The computer may not be abl e to start from an A C adaptor that is rated for less current (amperage) than the computer requires, e ven if the rated v oltage is correct, and the plug fits correctly[...]

152 If Something Goes Wrong The W indo ws ® operating system is not working ❖ Safe Mode with Command Pr ompt ❖ Enable Boot Logging ❖ Enable low-resolution video (640x480) ❖ Last Kno wn Good Conf iguration (adv anced) ❖ Directory Services Restore Mode ❖ Deb uggin g Mode ❖ Disable automatic restar t on system failure ❖ Disable Driv e[...]

153 If Something Goes Wrong Resolving a har dwar e conflict The Windows ® operating system can help you If the operating system has started properly but you still ha ve a problem using your co mputer , the onli ne Help can assist you in troubleshooting the pro blem. T o access the W indo ws ® operating system Hel p and Support: 1 Click Start , th[...]

154 If Something Goes Wrong Resolving a hardwar e conflict The device most recently connected to the system is th e one most likely to be causing a conflict. Resolving conflicts There are sev eral things you can do to resolve hardw are conflicts: ❖ Get the most recent dri vers from the manuf acturer . ❖ Disable the device. For an ol der de vice[...]

155 If Something Goes Wrong Resolving a har dwar e conflict ❖ The Resources tab, which lists resources assigned to the monitor , optional external opti cal driv e, optional external diskette dri ve, and other power -using functions. Thi s tab does not appear if the device is not using resources. ❖ The Driver tab, which displays the drivers bein[...]

156 If Something Goes Wrong Resolving a hardwar e conflict For this model Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in Slot A. Power and the batteries Y our computer receive s its po wer through the AC ada ptor and power cord/cable or from the system batteries (battery , op[...]

157 If Something Goes Wrong Resolving a har dwar e conflict The battery appears not to power the computer f or as long as it usually does. If you frequently repeat shallow char ge and discha rge, the battery meter may become in accurate. Let the battery discha rge completely , then try charging it ag ain. Check the po wer options vi a your Po wer P[...]

158 If Something Goes Wrong Resolving a hardwar e conflict Display problems Here are some typical displ ay problems and their sol utions: The screen is blank. Display Auto Off may ha ve gone into ef fect. Press any ke y to acti vate the screen. Y ou may have acti v ated the instan t password feature by pressing Fn and F1 simultaneously . If you ha [...]

159 If Something Goes Wrong Resolving a har dwar e conflict The built-in scr een flickers. Some flickering is a normal result of the way the screen produces colors. T o reduce the am ount of flickering, try u sing fewer colors. T o change the number of colors displayed: 1 Right-click in a blank area of the W indo ws ® desktop. 2 Click Personalize [...]

160 If Something Goes Wrong Resolving a hardwar e conflict Disk or internal storage drive problems Problems with the internal storage dri ve or with a diskette dri ve usually show up as an inability to access the dri ve or as sector errors. Somet imes a dri ve prob lem may cause one or more f iles to appear to hav e garbage in them. T ypical proble[...]

161 If Something Goes Wrong Resolving a har dwar e conflict Y our data files are damaged or corrupted. Refer to your software do cumentati on for file recov ery procedures. Many software packages automatically create backup files . Y ou may also be able to recover lost data using utility software. Consult your network administrator . Some programs [...]

162 If Something Goes Wrong Resolving a hardwar e conflict Y ou press the disc eject b utton, but the dri ve tray does not slide out. Make sure the computer is connect ed to a po wer source and turned on. The optical dri ve eject mechanism requires power to operate. Make sure a program is not accessi ng the driv e and preventing it from ejecting. I[...]

163 If Something Goes Wrong Resolving a har dwar e conflict The computer emits a loud , high-pitched noise. This is feedback between the mi crophone and the speakers. It occurs in any sound system when inpu t from a micropho ne is fed to the speakers and the speak er volume is too loud. Adjust the volume control. ExpressCard ® problems ExpressCard[...]

164 If Something Goes Wrong Resolving a hardwar e conflict 2 Double-click the appr opriate ExpressCard, which w ill be listed under one of the categories show n, for e xample: Disk dri ves, Network adapters, Other , etc. The operating system displays your ExpressCar d’ s Propert ies dialog box, which contains informati on about your ExpressCard c[...]

165 If Something Goes Wrong Resolving a har dwar e conflict An ExpressCard ® er ror o ccurs. Reinsert the card to make sure it is properly connected. If the card is attached to an e xternal device, check that the connection is secure. Refer to the card’ s documentation, which should contain a troubleshooting section. Printer problems This sectio[...]

166 If Something Goes Wrong Resolving a hardwar e conflict Modem problems (A vailable on certain models) This section lists comm on modem problem s. The modem will not r eceive or transmit pr operly . Make sure the cable from the modem to the telephone line is firmly connected to the computer’ s modem port and the telephone line jack. Check the c[...]

167 If Something Goes Wrong Resolving a har dwar e conflict T o determine if your computer has an internal Wi-Fi ® adapter , check the device list in Device Manager (part of the Windows ® Control Panel, Hardware and Sound). Some T oshiba models may have a Wireless antenna ON/OFF switch even though they do not have an internal Wi-Fi ® adapter . ?[...]

168 If Something Goes Wrong Resolving a hardwar e conflict 3 At the top-left of the Start menu, click cmd.exe to open the command prompt. 4 Enter IPCONFIG / ALL and press Enter . The IP address for each activ e network adapter will be displayed. ❖ Connect your computer directly to your router or broadb and modem, by plugging a standard CA T5 Ethe[...]

169 If Something Goes Wrong D VD operating pr oblems DVD operating problems If you experience a problem playing D VDs, you may be able to fix the problem yourself. For general problems playing a D VD title, try the following steps: 1 V erify that the disc is in a format that the dri ve supports. 2 Ensure that the disc is proper ly inserted in the d[...]

170 If Something Goes Wrong Develop good computing habits Develop good computing habits Sa ve y our work fr equently . Y ou can never predict when your co mput er will lock, fo rcing you to close a program and lose unsaved changes. Man y software programs build in an automatic backup, but you should not rely solely on this feature. Save your work! [...]

171 If Something Goes Wrong Develop good computing habits Data and system configuration backup in the Windows ® operating system The W indo ws ® operating system offers some easy-to-use features for backing up your Windo ws ® settings and your data—documents and other important files. T ake advantage of these features to protect yourself from [...]

172 If Something Goes Wrong Develop good computing habits Then, at a later time, you can re-establish your Windo ws ® configuration using the saved Restore Point. T o do this: 1 Click Start , All Programs , Acces sories , System T ools , and then System Restore . 2 Click Next . 3 A list of previously created Restore Points displays, showing the ti[...]

173 If Something Goes Wrong Develop good computing habits Follo w these steps to back up y our computer or files to optical discs, or a storage driv e: Y ou cannot back up the computer while running on battery power . Connect the AC adaptor before continuing. 1 Prepare your backup tar get by c onnecting it and/or inser ting a blank optical disc in [...]

174 If Something Goes Wrong Develop good computing habits ❖ Back up your critical data (see “Backing up your data or you r entire computer with the Windo ws® operating system” on page 172 ). ❖ Hav e your factory Restore/Reconfiguration CD(s) on hand in case you need any f iles from them (available on certain models). ❖ Do not guess—fol[...]

175 If Something Goes Wrong If you need further assistance If you need further assistance If you have follo wed the recomm endations in this chapter and are still having problems, you may n eed additional technical assistance. This section contains the step s to take to ask for help. Before you contact T oshiba Since some problems m ay be related t[...]

176 If Something Goes Wrong Other T oshiba Internet W eb sites T oshiba voice contact Before calling T o shiba, make sure you have: ❖ Y our computer’ s serial number ❖ The computer and any optional devices related to the problem ❖ Backup copies of your Wi ndows ® operating system and all other preloaded software on your choice of media ❖[...]

177 If Something Goes Wrong T oshiba’ s worldwide of fices For more information on additio nal T osh iba worldwide locations, please visit: www .toshiba. co.jp/i ndex. htm . France T o shiba Systèmes (France) S.A. 7, Rue Ampère; B. P . 131 92800 Puteaux Cédex France Germany T oshiba Europe GmbH Leibnizstraße 2 D-93055 Regensbu rg Germany Ital[...]

178 5.375 x 8.375 ver 2.3 Appendix A Hot Keys/TOSHIBA Cards Hot ke ys and TO SHIB A Cards provi de a quick way to modify selected system functions and to launch applications. There are two types of T OSHIB A Cards: Hot Ke y Cards and Application Cards. Hot Key Cards The Hot Ke y Cards are used to set or modify the following system functions: ❖ Mu[...]

179 Hot Keys /TOSHIBA Ca rds Hot K e y Car ds 5.375 x 8.375 ver 2.3 Using the Hot Key Cards The Hot Ke y Cards are normally hidden from view . The Cards appear when you press the Fn key . Hot keys are keys that, when pressed in combina tion with the Fn key , turn system functions on and off. Hot keys have a legend on the key indicating the option o[...]

180 Hot Keys/TOSHIBA Cards Application Car ds 5.375 x 8.375 ver 2.3 Application Cards The Application Cards are used to launch these applications: Not all functions are supported on all models. TOSHIB A Assist For more information, refer to “TOSHIB A Assist” on page 126 . PC Diagnostic T ool utility For more information, refer to “TOSHIB A PC[...]

181 Hot Keys /TOSHIBA Ca rds Application Cards 5.375 x 8.375 ver 2.3 Using the Application Cards T o launch an application using the Application Card s: 1 Press and hold the Fn ke y . The TOSHIB A Cards display at the top of the screen. (Sample Image) TOSHIB A Car d display 2 Click the “stack ed” card on the far right of the display . The Appli[...]

182 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 3 The Card Case displays tw o rows of Cards. Cards that appear solid (not tr ansparent) in the bottom ro w are enabled and can be selected when the Application Cards are displayed. The top row contains all of the disabled cards. 4 T o enable a card, drag it from the top ro w to the[...]

183 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Lock (Instant security) The Fn + F1 hot key function acti v ates instant security . The user logon screen will appear and a user with a valid account will need to log back on to gain access to the computer . or Fn + This TOSHIB A Card or hot ke y blanks the display . Selecting th[...]

184 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Power plan or Fn + This TOSHIB A Card or hot ke y displays the power plans and cycles through the power plans. The properties of each po wer plan, and the po wer plans that are displayed by this function, are set in the Power Options window . Selecting this Card or pressing the hot[...]

185 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Sleep mode or Fn + This TOSHIB A Card or hot k e y places the computer into Sleep mode. For more information about Sleep mode, please see “Using and configuring Sleep m ode” on page 73 . Selecting this Card or pressing the hot ke y displays the following options: (Sample Imag[...]

186 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Hibernation mode or Fn + This TOSHIB A Card or hot k e y places the computer into Hibernatio n mode. If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see “Using and configuring Hibernation mode” on page 70 . Selecting thi[...]

187 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Output (Display switch) or Fn + This TOSHIB A Card or hot ke y cycles through the power - o n d i sp l a y o p t io n s (only the f irst option is av ailable when you do not have an external monitor attached) (the last option is available only if you are in Extend ed Display Mode[...]

188 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Display brightness Cycle through the display modes, th en select the desired mode. Not all functions are supported on all models. Some systems also support an additional Swap Image Display mode. This mode is available only if the current setting is an extended desktop mode (Built-i[...]

189 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Disabling or enabling wireless devices or Fn + This TOSHIB A Card or hot ke y enables/disables th e optional wireless devices installed in your computer . The wireless modes are: ❖ Wi - F i ® enabled—Enables just the W i-Fi ® module. ❖ Bluetooth ® enabled—Enables just [...]

190 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Disabling or enabling the T ouchPad™ or Fn + This TOSHIB A Card or hot ke y enables/disables th e T o uchPad. For more information on using the T ou chPad, see “Disabling or enabling the T ouchPad™” on page 61 . Selecting this Card or pressing the hot key displays the follo[...]

191 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Zoom (Display resolution) or Fn + [ Space bar ] This TOSHIB A Card or hot key switches screen resolution. Selecting this Card or pressing the hot ke y displays the following options: (Sample Image) Scr een r esolution options Cycle through the screen resolu tions, then select the[...]

192 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Keyboard hot key functions Fn + This hot k ey turns the curs or control overlay on and off. Fn + This hot k ey turns the numeric overlay on and of f. Fn + This hot k ey turns the scroll lock feature on and off. Fn + This hot key tu rns the TO SHIB A Zo o mi ng Utility to zoom-out. [...]

193 5.375 x 8.375 ver 2.3 Appendix B P o wer Cord/Cable C o nnector s Y our c omputer ships with the corr ect po wer supply for the country of purchase. This appendix shows the shapes of the typical A C po wer cord/cable connectors fo r v arious parts of the world. USA and Canada UL ap pr oved CS A a pp rove d United Kingdom BS ap pr oved Australia[...]

194 Glossar y TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer . Acronyms The follo wing acronyms may app ear in this user’ s guide. AC alternating current BIOS basic input/output system bps bits per second CD compact disc CD-R OM compact disc read-only memory CD-R W compact disc re write memory CMOS co[...]

Glossary 195 DOS disk operating system DPI dots per inch DSTN dual supertwist nem atic DV D digital versatile (or video) disc DV D - R O M dig ital versatile (or video) disc read-only m emory ECP enhanced capabilities po rt EPR OM erasable programmable read-only memory FAT f ile allocation table FCC Federal Communicat ions Commission GB gigabyte HD[...]

196 Glossary SDRAM synchronous dynamic random access memory SRAM static random access memory SSD Solid State Driv e SVGA super video graphics adapter TFT thin film transistor USB univ ersal serial b us URL uniform resource lo cator WA N wide area netw ork www W orld Wide W eb Te r m s The following terms may appear in this user’ s guide. A active[...]

Glossary 197 baud rate — The speed at which a comm unication de vice, such as a printer or mo dem, transmits in formation. Baud rate is the nu mber of signal changes per second (not necessarily the same as bits per second). See also bits per second . BIOS (basic input/ output syst em) — Basic instructions, stored in read- only memory (R OM), co[...]

198 Glossary central processing unit (CPU) — The chip that functions as the “brain” of the computer . It takes informa tion from outside sources, such as memory or keyboard input, processes the information, and sends the results to another device that uses the information. character — Any letter , number , or symbol you can use on the compu[...]

Glossary 199 D default — The setting selected by a program when the user does not specify an alternati ve setting. device — A component attached to the computer . Devices may be external (outside the computer’ s case) or internal (inside the computer’ s case). Printers, disk dr iv es, and modems are examples of devices. device dri ver — A[...]

200 Glossary double-click — T o press and release the pointing device’ s primary button rapidly twice without moving the pointing device. In the W indows ® operating system, this refers to the pointing device’ s left button, unless otherwise stated. double-density d iskette — A 3.5-inch diskette that can hold up to 720 KB of information (h[...]

Glossary 201 F fil e — A collection of related information, saved on disk with a unique name. A file may be a program, information used by a program, or a document. See also docum ent. f ile allocation table (F A T) — The section of a s t o r a g e d r iv e that keeps track of the location of stored files. fil e n a m e — A set of characters [...]

202 Glossary Hibernation — A feature of many T oshiba computers that sav es to the i n t e r n a l s t o r a g e d r iv e the current state of your work, including all open files and programs, when you turn the computer off. When you turn on the computer again, your work is returned to the same state it was when the computer was turned of f. See [...]

Glossary 203 liquid crystal disp lay (LCD) — A type of display that uses a liquid substance between two transparent electrode panels. When an electric current passes through the electrodes, the molecules in the liquid form a crystalline pattern that polarizes the light passing through it. A filter o ver the electrodes permits only non-polarized l[...]

204 Glossary N network — A collection of computers a nd associated de vices that are connected by communications facilities. A network allows you to share data and peripheral de vices, su ch as printers, with other users and to exchange electronic mail. non-interlaced — A method of refreshing a computer scr een, in which each pixel of e very li[...]

Glossary 205 Plug and Play — Generally , refers to the com puter’ s ability to automatically configure itsel f to work with peripheral devices. When capitalized, refers to a sta ndard that, when followed by a device manufacturer , allo ws a computer to conf igure itself automatically to work with the device. pointing de vice — Any de vice, su[...]

206 Glossary RJ11 — A modular connector used o n most U.S. telephone syst ems and direct-connect modems. The RJ11 co nnector is a 6-wire connector . R OM (read-only memory) — Non-v olatile memory that can be read but not written to. Non-volatile here means that information in ROM remains whether or not the computer is recei ving power . This ty[...]

Glossary 207 T TFT display — See active-ma trix display . U universal serial bus (USB) — USB is a serial b us that supports a data transfer rate of up to 4 80 Mbps (480 million bi ts per second). USB can connect up to 127 peripheral de vices through a single all- purpose USB port. USB allows hot swapping of peripherals. See also bus, hot swappi[...]

208 Index A A C adaptor 46 AC p o w e r connecting adaptor 47 accessories memory 51 adding memory 51 Alt keys 80 Application Cards 180 audio fil e s 120 audio features 120 B backing up files 79 battery changing 104 charge indicator light 48 , 98 charge not lasting 157 charging 46 , 48 conserving po wer 101 disposal 109 lo w charge 100 monitoring po[...]

209 Index moving 76 non-system disk or disk error message 150 not accessing disk driv es 149 running on battery power 94 setting up 43 , 53 warning resume failure messag e 149 computer lock 77 computing tips 78 ConfigFree® 143 connecting to a power source 46 connection set up 115 control buttons 60 Ctrl keys 80 D desktop creating new icon 112 majo[...]

210 Index file e xtensions 85 file, backing up 79 fil e s backing up 86 printing 85 restoring 87 saving 84 Fn keys 80 function keys 81 H hardware conflicts 153 resolving 154 headphones using 120 Help and Support W indo ws® operating system 153 Hibernatio n mode 66 configuring 70 starting again from 72 hot key display brightness 188 Hibernatio n mo[...]

211 Index remo ving memory module slot cov er 54 memory module inserting 55 installation 52 removing 58 memory module slot 54 microphone 120 modem connecting to telephone line 115 problem solving 166 monitor 61 connecting 61 not working 158 mouse installing 63 mouse utility 136 N network accessing 115 Connect to the Internet 115 networking wireless[...]

212 Index cannot insert diskette in drive 161 cannot read a diskette 161 changing display properties 159 checking device properties 154 computer hangs when ExpressCard® inserted 164 computer will not power up 148 contacting T oshiba 175 corrupted/damaged d ata files 161 Device Manager 154 disk driv e is slow 160 display is blank 158 ExpressCard® [...]

213 Index sound problem solving 162 sounds recording 120 speakers using external 120 start button 113 Start Search field 83 starting a program 81 Start Search field 83 W indo ws® Explorer 82 W indows® Start menu 82 starting up the computer from Shut down 70 from Sleep 75 Startup menu problem solving 151 supervisor password, deleting 133 superviso[...]