Toshiba SATELLITE E105 manuale d’uso

Satellite E100/105 Maintenance Manual Toshiba Personal Computer Satellite E100 Satellite E105 (PSE10x) Maintenance Manual TOSHIBA CORPORATION S/ No[...]

ii Satellite E100/105 Maintenance Manual Copyright © 2008 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the inform ation contained herein. Toshiba Satellite E100/105 Mainte[...]

Satellite E100/105 Maintenance Manual iii Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Satellite E100/105, referred to as Satellite E100/105 in this manual. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Unit[...]

iv Satellite E100/105 Maintenance Manual The manual is divided into the following parts: Chapter 1 Hardware Overview describes the Satellite E100/105 system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations[...]

Satellite E100/105 Maintenance Manual v Conventions This manual uses the following formats to describe, identify, and highlight term s and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition. For example: Read Only Memory (ROM) Keys Keys are [...]

vi Satellite E100/105 Maintenance Manual Table of Contents Chapter 1 Hardware Overview 1.1 Features ................................................................................................................... .............1 1.2 System Unit Components ............................................................................................[...]

Satellite E100/105 Maintenance Manual vii Procedure 2 Connector Check and Replacement Check.................................... 2-15 2.7 Display ................................................................................................................. 2-1 6 Procedure 1 External Monitor Check ..................................................[...]

viii Satellite E100/105 Maintenance Manual 3.2.4 Hotkey Test ..............................................................................................8 3.2.5 Audio Play Test ........................................................................................8 3.2.6 Audio Record Test .........................................................[...]

Satellite E100/105 Maintenance Manual ix Safety Precautions ................................................................................................ 4-2 Before You Begin ................................................................................................ 4-4 Disassembly Procedures ................................................[...]

x Satellite E100/105 Maintenance Manual Installing the ODD Bay Module ....................................................................... 4-25 4.8 Display Assembly ................................................................................................ 4-26 Removing the Display Assembly...................................................[...]

Satellite E100/105 Maintenance Manual xi Removing the CCD Board and MIC ................................................................. 4-48 Installing the CCD Board and MIC ................................................................... 4-49 4.19 Power board, Bluetooth card, Bu tton board and Finger print board........................ 4-50 R[...]

xii Satellite E100/105 Maintenance Manual Appendices Appendix A Handling the LCD Module ........................................................................... A-1 Appendix B Board Layout .................................................................................................B-1 Appendix C Pin Assignments...............................[...]

Chapter 1 Hardware Overview i Satellite E100/E105 Maintenance Manual[...]

1 Hardware Overview ii Satellite E100/E105 Maintenance Manual[...]

1 Hardware Overview Satellite E100/E105 Maintenance Manual iii Chapter 1 Contents 1.1 Features ................................................................................................................... ............ 1 1.2 System Unit Components .................................................................................................[...]

1 Hardware Overview iv Satellite E100/E105 Maintenance Manual Figures Figure 1-1 ID Parts Description Placement ............................................................................... 6 Figure 1-2 Computer Block Diagram ........................................................................................ 7 Figure 1-3 System Board Configu[...]

1 Hardware Overview 1.1 Features 1 Satellite E100/E105 Maintenance Manual 1.1 Features The Toshiba Satellite E100/E105 is a full size notebook PC based on the Penryn and Merom and Celeron processor, providing high-speed pr ocessing capabilities and advanced features. The computer employs a Lithium Ion battery that allows it to be battery-operated f[...]

1 Hardware Overview 1.1 Features 2 Satellite E100/E105 Maintenance Manual The computer has two SO-DIMMs slot comes standard with DDRII-800MHz m odule. It supports PC2-6400 and uses SO-DIMMs (DDRII SDRAM) driven at 1.8 V, accepting BTO/CTO for your memory requirem ents. It can incorporate up to 8 GB for GM45 and 4GB of main mem ory for GL40. Using t[...]

1.1 Features 1 Hardware Overview Satellite E100/E105 Maintenance Manual 3 The keyboard has 3 kinds’ countries key.  Battery The computer has a removable 8 Cell Lithium Ion battery pack .  Universal Serial Bus (USB) Ports The computer has two USB 2.0 ports and one eSATA (External-SATA) with USB combination port. It is supported to daisy-chai[...]

1 Hardware Overview 1.1 Features 4 Satellite E100/E105 Maintenance Manual The internal LAN board supports 1Gbit, enabling connection to a LAN at up to 1Gbps. It also supports Wake-up on LAN from S3/S4/S5 and PXE boot support. The LAN board has RJ45 jack to directly accommodate a LAN cable.  Wireless LAN The internal Mini Card slot supports IEEE8[...]

1.1 Features 1 Hardware Overview Satellite E100/E105 Maintenance Manual 5 The FM Tuner Port lets you connect an external FM Antenna.  ROBSON Mini Card (BTO) Robson is Intel’s platform non-volatile mem ory (NVM) disk-cache accelerator which delivers a fast cold boot as well resume from hibernate while saving power. It also accelerates applicati[...]

1 Hardware Overview 1.1 Features  Figures 1-1/1-2/1-3 and 1-4 show the com puter and its system unit configuration, respectively. Figure 1-1 ID Parts Description Placement 6 Satellite E100/E105 Maintenance Manual[...]

1.1 Features 1 Hardware Overview Figure 1-2 Computer Block Diagram Satellite E100/E105 Maintenance Manual 7[...]

1 Hardware Overview 1.1 Features Figure 1-3 System Board Configurations 8 Satellite E100/E105 Maintenance Manual[...]

1.2 System Unit Components 1 Hardware Overview 1.2 System Unit Components Figure 1-4 is Block Diagram of the System Unit. Figure 1-4 System Unit Block Diagram Satellite E100/E105 Maintenance Manual 9[...]

1 Hardware Overview 1.2 System Unit Components 10 Satellite E100/E105 Maintenance Manual The system unit of the computer consists of the following com ponents:  Processor : Core2 Duo Processor. y Core2 Duo Processor (1066MHz) − Core speed: 2.53/2.80/2.93GHz − System bus: 1066 MHz − On-die level 2 cache: 6 MB − Core speed: 2.00/2.10/2.26/[...]

1.2 System Unit Components 1 Hardware Overview Satellite E100/E105 Maintenance Manual 11 − NvStorage size : 128K − NvStorage free space : 101K − FV00 size : 644K − FV00 free space : 37K − FV01 size : 64K − FV01 free space : 37K − FV02 size : 128K − FV02 free space : 5K  System Controllers y North Bridge: Intel GM45/GL40 − CPU I[...]

1 Hardware Overview 1.2 System Unit Components 12 Satellite E100/E105 Maintenance Manual  Card Bus Controller y R5C833 − PCI-1394 bridge interface − SD/Mini SD/SD-IO/MS/MS Pro/MMC/XD Card Controller − PCI Bus interface y R5C837 − SD/Mini SD/SD-IO/MS/MS Pro/MMC/XD Card Controller − PCI Bus interface  Audio Controller Realtek ALC268 i[...]

1.2 System Unit Components 1 Hardware Overview Satellite E100/E105 Maintenance Manual 13 − Universal I/O port − Battery capacity check − Flash memory reprogram ming function − EC access interface − I2C communication control  Battery EEPROM y 24C02 equivalent (128 words x 16 bits, I2C interface) integrated in battery pack. − Storing r[...]

1 Hardware Overview 1.3 2.5-inch HDD 1.3 2.5-inch HDD The computer contains an extremely low-pr ofile and lightweight, high-perform ance HDD. The HDD incorporates 9.5 mm height m agnetic disk and mini-Winchester type m agnetic heads. The HDD interface conforms to Serial ATA. Storage capacities supported are 100, 160, 200, 250, 320, 500 GB. The HDD [...]

1 Hardware Overview 1.4 DVD Super Multi (+-R Double Layer) 1.4 DVD Super Multi (+-R Double Layer) The DVD Super Multi drive accepts 12-cm (4.72-inch) and 8-cm (3.15-inch) discs. At maximum , the drive can play back a DVD at 8x speed, read CD-ROM at 24x speed, and write CD-R at 24x speed, CD-RW at 4x speed, US CD-RW at 16x speed, High Speed CD- RW a[...]

1 Hardware Overview 1.5 Power Supply 16 Satellite E100/E105 Maintenance Manual 1.5 Power Supply The power supply unit provides many different voltages for the system board and perform s the following functions: 1. Power input monitor y Checks whether the DC power supply (AC adapter) is connected to the computer. y Checks whether the battery pack is[...]

5B1.6 Batteries 1 Hardware Overview Satellite E100/E105 Maintenance Manual 17 1.6 Batteries The computer has the following three types of batteries:  Main Battery Pack  Real Time Clock (RTC) Battery Table 1-3 lists the specifications of these batteries. Table 1-3 Battery specifications Battery Ty pe Material Output voltage Capacity Main Batte[...]

1 Hardware Overview 1.6 Batteries 18 Satellite E100/E105 Maintenance Manual Table 1-4 Quick/Normal charging time State Charge Time Off-State Charge 8 Cell About 4 hours max On-State Charge 8 Cell About 4~10 hours max NOTE: The time required for normal charge depends on the power consumption by the system. Using the fluorescent lamp and frequently a[...]

2 Troubleshooting 2-i Satellite E100/E105 Maintenance Manua l 2 概要 Chapter 2 Troubleshooting[...]

2 Troubleshooting 2-ii Satellite E100/E105 Main ten ance Manual Chapter 2 Contents 2.1 Outline .................................................................................................................... 2-1 2.2 Basic Flowchart ...................................................................................................... 2-2 2.3 Pow[...]

2 Troubleshooting Satellite E100/E105 Main ten ance Manual 2-iii Procedure 2Connector Check ........................................................................ 2-21 2.11 Audio Test ............................................................................................................ 2-22 Procedure 1 Test Program Check ...................[...]

2 Troubleshooting 2-iv Satellite E100/E105 Main ten ance Manual Figures Figure 2-1 Basic flowchart .............................................................................................. 2-3 Tables Table 2-1 HDD error code and status ........................................................................... 2-13[...]

2.1 Outline 2 Troubleshooting Satellite E100/E105 Main ten ance Manual 2-1 2.1 Outline This chapter describes the fault diagnosis proced ures for field replaceable units (FRUs) in the computer. The FRUs covered here are as follows: 1. System board 2. HDD 3. Keyboard 4. Display 5. ODD drive 6. LAN 7. Finger Print 8. Speaker 9. IEEE 1394 10. Cooling [...]

2 Troubleshooting 2.2 Basic Flowchart 2-2 Satellite E100/E105 Main ten ance Manual 2.2 Basic Flowchart The basic flowchart in Figure 2-1 serves as a guide for identifying a possibly faulty FRU. Before going through the diagnostic flow chart steps, verify the following:  Ask the user if a password has been register ed and, if so, ask him or her t[...]

2.2 Basic Flowchart 2 Troubleshooting Satellite E100/E105 Main ten ance Manual 2-3 Star t Connect the AC Adapter DC IN LED on ?? BATTERY LED on ?? Turn the power on. Any error message displayed ?? Message "In Touch with Tomorrow Toshiba" displayed Follow the power supply diagnostic p rocedure in Section 2.3 N o Follow the power supply dia[...]

2 Troubleshooting 2.2 Basic Flowchart 2-4 Satellite E100/E105 Main ten ance Manual Figure 2-1 Basic flowchart (2/2) Keyboard works well ?? Follow the keyboard diagnostic procedure in Section 2.6 1 N o Insert Bootable CD into ODD Diagnostic Program Loaded ?? Perform each test with the diagnostic program. Any error detected by the diagnostic program [...]

2.2 Basic Flowchart 2 Troubleshooting Satellite E100/E105 Main ten ance Manual 2-5 If the diagnostic program cannot detect an er ror, the error may be interm ittent. Run the continuous test program repeatedly to isolate th e problem. Check the log utilities function to confirm which diagnostic test detected th e error, then perform the appropriate [...]

2 Troubleshooting 2.3 Power Supply 2-6 Satellite E100/E105 Main ten ance Manual 2.3 Power Supply The power supply in the computer controls ma ny functions and com ponents. To check if the power supply is defective or malfunctioning, foll ow the troubleshooting procedures below as instructed. Procedure 1 Power Icon Check Procedure 2 Connection Check[...]

2.3 Power Supply 2 Troubleshooting Satellite E100/E105 Main ten ance Manual 2-7  DC IN LED DC IN LED Power supply status On in White DC power being supplie d (from the AC adapter) Off Battery damage and can’t charg e duri ng DC-in. Off Else If the DC IN LED off, follow the steps below: 1. Remove the battery pack and the AC ad apter to shut off[...]

2 Troubleshooting 2.3 Power Supply Procedure 2 Connection Check Power is supplied to the system board as illustrated below: AC adaptor System board AC power cord AC adaptor cord Battery pack Follow the steps below to check whether each connector has been connected correctly: Check 1 Make sure the AC adaptor and AC power cord have been firmly plugg [...]

2.4 System Board 2 Troubleshooting Satellite E100/E105 Main ten ance Manual 2-9 2.4 System Board To check if the system board is defectiv e or malfunctioning, f ollow the troubleshooting procedures below as instructed. Procedure 1 Message Check Procedure 2 Test Program Check Procedure 3 Replacement Check Procedure 1 Message Check When the power is [...]

2 Troubleshooting 2.4 System Board 2-10 Satellite E100/E105 Main ten ance Manual Procedure 2 Test Program Check The maintenance test program contains seve ral program s for diagnosing the system board and CPU. Execute the following test programs using the procedures described in Chapter 3. 1. System test 2. Memory test 3. Keyboard test 4. Display t[...]

2.5 2.5-inch HDD 2 Troubleshooting Satellite E100/E105 Main ten ance Manual 2-1 1 2.5 HDD To check if the 9.5mm or 12.5mm HDD is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Message Check Procedure 2 Partition Check Procedure 3 Format Check Procedure 4 Test Program Check Procedure 5 Connector C[...]

2 Troubleshooting 2.5 2.5-inch HDD 2-12 Satellite E100/E105 Main ten ance Manual create a DOS partition on drive C. Then restart the computer.. If the problem persists, go to Procedure 3. Check 3 If drive C is listed as active in the FDISK menu, perform Check 4. If drive C is not listed as active, return to the FDISK menu and choose the option to s[...]

2.5 2.5-inch HDD 2 Troubleshooting Procedure 4 Test Program Check Run the HDD test program stored on the maintena nce test program disk for all test items. See Chapter 3 for details on how to use the test program. If an error is detected during the HDD test, an error code and status will be displayed. The error codes and their status names are list[...]

2 Troubleshooting 2.5 2.5-inch HDD Procedure 5 Connector Check an d Replacement Check The HDD or system board may be faulty. Di sassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1 Make sure the following connect ors have been firmly connected to the HDD, system board and CPU. HDD System board [...]

2.6 Keyboard 2 Troubleshooting 2.6 Keyboard To check if the computer’s keyboard is defective or malf unctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Ch eck and Replacement Check Procedure 1 Test Program Check Execute the Keyboard test availa ble as part of the maintenan c[...]

2 Troubleshooting 2.7 Display 2.7 Display To check if the computer’s display is def ective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 External Monitor Check Procedure 2 Test Program Check Procedure 3 Connector Ch eck and Replacement Check Procedure 1 External Monitor Check Connect an external monitor[...]

2.7 Display 2 Troubleshooting Check 3 The FL may be fault y. Replace it w ith a new one and return to Procedure 3. If there is still an error, perform Check 4. Check 4 The FL inverter board may be fa ulty. Replace it with a new one and return to Procedure 3. If there is still an error, perform Check 5. Check 5 Make sure the LCD/FL cable has been fi[...]

2 Troubleshooting 2.9 LAN 2.8 ODD (Optical Disk Drive) To check if the internal ODD drive is defec tive or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 ODD Cleaning Check Procedure 2 Test Program Check Procedure 3 Connector Check and Replacement Check Procedure 1 ODD Cleaning Check 1. Turn off the power to [...]

2.12 LAN 2 Troubleshooting Satellite E100/E105 Main ten ance Manual 2-1 9 Check 3 The ODD drive may be faulty. Replace the ODD drive with a new one following the steps in Chapter 4. If the ODD drive is still not functio n ing properly, perform Check 4. Check 4 The system board m ay be faulty. Replace it w ith new one following the instructions in C[...]

2 Troubleshooting 2.9 LAN 2-20 Satellite E100/E105 Main ten ance Manual 2.9 LAN To check if the computer’s LAN is defec tive or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Ch eck and Replacement Check Procedure 1 Test Program Check Execute the LAN check program av[...]

Finger Print(Optional) 2.10 Finger Print(Optional) 2 Troubleshooting Satellite E100/E105 Main ten ance Manual 2-2 1 2.10 Finger Print(Optional) To check if the computer’s Finger Print is defective or m alfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check Procedure 1 T[...]

2 Troubleshooting 2.10 Audio Test 2.11 Audio Test To check if the computer’s Speaker is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Ch eck and Replacement Check Procedure 1 Test Program Check Execute the Audio test available as part of th e maintenanc[...]

2.12 IEEE 1394 Test 2 Troubleshooting Satellite E100/E105 Main ten ance Manual 2-2 3 2.12 IEEE 1394 Test To check if the computer’s IEEE 1394 is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check Procedure 1 Test Program Check Execute the IEEE 1394 tes[...]

2 Troubleshooting 2.13Cooling Module 2.13 Cooling Module To check if the computer’s cooling module is defective or malfunctioning, f ollow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check and Replacement Check Procedure 1 Test Program Check Execute the Fan On/off test program available[...]

2.13 Cooling Module 2 Troubleshooting Satellite E100/E105 Main ten ance Manual 2-2 5[...]

Chapter 3 Diagnostic Programs[...]

3 Diagnostic Programs ii Satellite E100 Maintenance Manual Chapter 3 Contents 3.1 General .......................................................................................................................... 1 3.2 Quick Start .................................................................................................................... 3 [...]

3 Diagnostic Programs Satellite E100 Maintenance Manual iii 3.7 Storage ........................................................................................................................ 46 3.8 Video ........................................................................................................................... 50 3.9 Communication[...]

[...]

3.1 General 3 Diagnostic Programs Satellite E100 Maintenance Manual 1 3.1 General This chapter explains the dia gnostic programs which tests and di agnoses the functions of the hardware components of this computer. The di agnostic programs can be classified into two types: OPTION and DIAGNOSTIC TEST. NOTE 1: This Diagnostic supports Minneapolis10 N[...]

3 Diagnostic Programs 3.1 General 2 Satellite E100 Maintenance Manual Before running the diagnostic programs, get the following tools prepared:  A Service Diagnostic BOOT CD  A Formatted FLOPPY DISK  A Test Media CD (A-BEX TEST CD-R OM TCDR-702)(for CD-ROM test)  A Test Media DVD (Toshiba-EMI DVD-ROM TEST DISK TSD-1)  An External Mon[...]

3.2 Quick Start 3 Diagnostic Programs 3.2 Quick Start When the system is booting from Service Di agnostic CD, the following screen will be displayed: Please select a test item or select 0 to exit to Free -DOS: 3.2.1 Quick Test When this item is selected, the syste m will run the configured test item s and genera te a test report automatically. When[...]

3 Diagnostic Programs 3.2 Quick Start 1. Use arrow key to select ‘TouchPad’ item on ‘Peripheral’ in the m enu, then press Space key to select it. (When it is being selected, there is a X marked in the [ ] ) Select ‘Test Mouse’ or press F8 to run the test. The prom pt information would be displayed in the screen as below. T his test item[...]

3.2 Quick Start 3 Diagnostic Programs Here is another method to run the test: Highlight a test item by using arrow keys, then, press Enter to start. If there are para meters provided, user should set parameters in the parameter dialog window. CPU Speed Test (Step by Step): 1. Select test item: Select System — CPU — CPU Speed , then, press the E[...]

3 Diagnostic Programs 3.2 Quick Start 3. Test Result System will automatically run and display the tes t result as follows: Following is the comparison report of the two testing methods m entioned above: 1) Configuration and Running As to the method used in Mouse test, the user is required to select test items by pressing Space key and set the para[...]

3.2 Quick Start 3 Diagnostic Programs As to the method adopted in CPU Speed test , user should highlight the test item and press Enter to start testing. And the user has to setup the parameters every time before running the test. Using this method, onl y one test item would be tested at one time. 3.2.3 Keyboard Layout test The test purpose is to ch[...]

3 Diagnostic Programs 3.2 Quick Start It requires user to press the key and ch eck whether the key in the screen changes color or not. User can terminate test by typing ‘ END ’. When testing the ‘ Fn ’ key, it must press the ‘ Enter ’ key at the sam e time. When the user has checked all the keys and all the keys in the screen have chang[...]

3.2 Quick Start 3 Diagnostic Programs 3.2.6 Audio Record Test Check whether the system could record the sound normally. If there is no error during the whole test, Pass; otherwise Fail. Th e test will repeat for four times. When the test is completed, a file named autest .log will be saved in the defined location. 3.2.7 DMI Read Read the informatio[...]

3 Diagnostic Programs 3.2 Quick Start During the editing, user could press F2 to confirm the DMI attribute update or press F4 to ignore the modification. Press ESC to exit the program of DMI W rite. The confirmation screen is as below: The attributes that have been modified woul d be marked in red; otherwise in yellow. User could press F2 to save t[...]

3.2 Quick Start 3 Diagnostic Programs The display of a test program and the set method of PC are shown below. Display of a Test Program The portion which PC and Test -Fixture contact is green. Set method of PC 3 Test1 Judgment If all data is less than ranges, it will b e OK. Z Upper X Satellite E100 Maintenance Manual 11[...]

3 Diagnostic Programs 3.2 Quick Start The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC 4 Test2 Judgment If all data is less than ranges, it will b e OK. 12 Satellite E100 Maintenance Manual Rear Uppe r[...]

3.2 Quick Start 3 Diagnostic Programs The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC 5 Test3 Judgment If all data is less than ranges, it will b e OK. Uppe r Right Satellite E100 Maintenance Manual 13[...]

3 Diagnostic Programs 3.2 Quick Start The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC 6 Test4 Judgment If all data is less than ranges, it will b e OK. Uppe r Front 14 Satellite E100 Maintenance Manual[...]

3.2 Quick Start 3 Diagnostic Programs The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC 7 Test5 Judgment If all data is less than ranges, it will b e OK. 8 Inspection Judgment If all data is less than ranges, it will b e OK. 9 Setting Calibration data When an inspection result is O.K.[...]

3 Diagnostic Programs 3.2 Quick Start 3.2.10 System Information This function is used to read the system information. When the test is com pleted, a file named System.log will be saved in the defined location. During the reading process, the following screen will be displayed to indica te that the progress is in detection: On the left column of the[...]

3.2 Quick Start 3 Diagnostic Programs User can use function keys listed on the bottom of the screen to display the configuration of the component or exit the current program . On the left column, the components information is listed and user can use arrow keys or PgUp/PgDn to view the list and highlight the chosen component . On the right column, t[...]

3 Diagnostic Programs 3.2 Quick Start 3.2.12 Exit to Free DOS Select this item to exit to Free DOS. 3.2.13 The Diagn ostics Screen Explanation Below is an example of running a test item. It includes the following parts: Diagnostics Windows, Test Stat us Area, Progress Bar, Error List, Test Item ’s Title, Status Bar and Message Box. 1. Diagnostics[...]

3.2 Quick Start 3 Diagnostic Programs  The error list of each test m odule is displaye d at the lower right corner of the scr It would d een. isplay the total e rror quantity found in the test, the most recent five error codes and description would be shown here . Detailed error report could be viewed er to select. Pressing ESC key to interrupt [...]

3 Diagnostic Programs 3.2 Quick Start 20 Satellite E100 Maintenance Manual  Test Mode : TIMEBOUND or LOOPBOUND, e.g. LOOPBOUND in the above screen;  Script File Name : Script file nam e, e.g. ‘ Custom .INI’ in the above screen;  Current Time(C. TIME) : Current system time, e.g. ‘C.TIME:2008-0 2 -16 0 in the above screen; 0 :42:40’ [...]

3.3 Options 3 Diagnostic Programs 3.3 Options 3.3.1 Overview In Service Diagnostics, with the Options menu user can configure the batch parameters, test item’s param eters and t hose parameters created by the LOG file. Options Menu Notes: • Select All/None Items Switch between selecting a ll test items and selecting none. T he hot key is F6 . ?[...]

3 Diagnostic Programs 3.3 Options 22 Satellite E100 Maintenance Manual Configure batch parameters and a ll the test item’s param eters . • Load Batch Parameters Upload all the test items and the param eters to the *.ini file. • Save Batch Parameters Save all the parameters and the test item s that are configured in the editor to a specified f[...]

3.3 Options 3 Diagnostic Programs • Test Order Specify the order of the test items. C hoose 'Sequence' to adopt the sequential mode; choose 'Random' to run the test items in random sequence. • Test Options Choose one of the following options: 9 Wait On Error Wait for further confirmation while an error occurs. 9 Break On Err[...]

3 Diagnostic Programs 3.3 Options Monitor the remaining ba ttery capacity (percent). 9 Monitor CPU Thermal Monitor the CPU temperature. • Test Mode 9 LOOPBOUND The chosen test items will run repeated ly accord ing to the times specified in the 'Number of Loops'. 9 TIMEBOUND The chosen test items will run for an exte nt tim e specified i[...]

3.3 Options 3 Diagnostic Programs Repeat times of the test item. • Interactive If the item is enabled during the test, the te s t items that need user to response can run normally, such as PS2 Mouse te st; If it is disabled, those test item s will report FAIL. Whether the option here is enabled, it only affects the current test item. • Paramete[...]

3 Diagnostic Programs 3.3 Options In this window, you can specify the .INI files that you wanted to be edited or modified. 3.3.5 Save Batch Parameters Here you can save the edited or modified content to the batch parameters files. 26 Satellite E100 Maintenance Manual[...]

3.3 Options 3 Diagnostic Programs 3.3.6 LOG Parameters Setting You can access the Log Parameters screen through Service DiagnosticsOptions - Generate Report. • Report Destination If selecting 'NONE', no log file will be generated ; if selecting 'FILE' , a log file with the name specified in 'Log File Name' will be g[...]

3 Diagnostic Programs 3.3 Options If selecting this parameter, erro rs and time will be recorded only when the test fails. 9 Append to Old Log File If selecting this parameter, the new lo g will be added to the old one. 9 Log Device Info on Fail If selecting this parameter, deta ils of the failed test will be recorded. • Log file Name Specify the[...]

3.3 Options 3 Diagnostic Programs In this screen, you can specify a Log file and view it with the viewer designated in Specify LOG Viewer. 3.3.9 LOG Viewer Service Diagnostic Log viewer: • ↑ , ↓ Scroll a line backward or forward on the screen. • Page Up, Page Down Satellite E100 Maintenance Manual 29[...]

3 Diagnostic Programs 3.3 Options 30 Satellite E100 Maintenance Manual Scroll a page backward or forward on the screen. • Esc Exit the Log viewer. • F1 Display the Help information about the Log viewer operations and the functional keys. • Ctrl+Home Go to the start of the log file. • Ctrl+End Go to the end of the log file. • Ctrl+F3 Promp[...]

3.3 Options 3 Diagnostic Programs Satellite E100 Maintenance Manual 31 Base Memory Test : PASS Extended Memory Test : PASS End Time: Wed Jul 05 10:47:51 2006 <Module Name>: Service Diagnostic Ver 1.00 ... Mouse Test Build Date 2006.01.10 [MSTPad] Begin Time: Wed Jul 05 10:48:54 2006 Touch Pad Test : FAIL ITEM TEST FAIL Function ID :502 Error [...]

3 Diagnostic Programs 3.4 Subtests 32 Satellite E100 Maintenance Manual 3.4 Subtest Test Group Sub Item ID Subtest Test ID Test items Internal Name System 01 CPU 01 Basic Functionality Test [CPUBasicFun] 02 CPU Speed [CPUSpeed] 03 Coprocessor NPU Basic Functions NPU Interrupt Coprocessor [NPUFun ] [NPUInterrupt] 04 CPU Information [CPUInformation] [...]

3.4 Subtests 3 Diagnostic Programs Satellite E100 Maintenance Manual 33 02 Random Increment Read/Write [RandIncr] 11 Data Bus Test [DataBus] 12 Memory Speed Test [MemSpeed] Storage 01 HDD 01 Sequential/Random R/W [SeqRdRW1] 02 Sequential/Random Seek [Seek1] 03 Performance [Perform1] 04 Controller Check [Controller1] 05 Diagnostic Read/Write [DiagRW[...]

3 Diagnostic Programs 3.4 Subtests 34 Satellite E100 Maintenance Manual VESA 1024x768x32 K Mode VESA 1024 x 768 x 16 K Mode VESA 1024 x 768 x32bit Mode [V1024768_32] 04 1 280 X 800 Video Modes VESA 1 280 x 800 x256 Mode VESA 1 280 x 800 x64K Mode VESA 1 280 x 800 x32 K Mode VESA 1 280 x 800 x 16 K Mode VESA 1 280 x 800 x32bit Mode [V1 280800 _15] [[...]

3.5 System Test 3 Diagnostic Programs 3.5 System Test Move arrow keys and press the Space key to select CPU test item from Service Diagnostic menu, then highlight CPU and press the Enter to run this test item. Subtest 01 CPU 1. Basic Functionality Test This test item is to check whether the CPU works normally through math and logic calculation, whi[...]

3 Diagnostic Programs 3.5 System Test CPU Speed Comparison --Whether you want to make a comparison of the CPU speed with the value set in ‘E xpected CPU Speed’, you should choose ‘Yes’; otherwise, ‘No’. Expected CPU Speed --Specify the expected CPU Speed value you want for further comparison. Allowable Error Rate -- Specify the Allowabl[...]

3.5 System Test 3 Diagnostic Programs 5. CPU Protected Mode Test This test item is to check whether CPU protected m ode instruction works normally. 6. MMX The test item is to confirm whether the CPU supports MMX instru ctions. Subtest 02 Boards 1. DMA Controller This test item is to check whethe r the DMA controller works norm ally. 2. Interval Tim[...]

3 Diagnostic Programs 3.5 System Test This test item is to check: 1. Whether the current system supports Plug-n-Play; 2. Whether there is an ESCD (Extended System Configuration D ata) in the BIOS; 3. Whether there is PCI-to-ISA bridge in the system; 4. Whether there is PCI bus in the sy stem. 6. ACPI Test ACPI test includes two sub-items as below: [...]

3.5 System Test 3 Diagnostic Programs Satellite E100 Maintenance Manual 39[...]

3 Diagnostic Programs 3.6 Memory Test 3.6 Memory Test This test module is to check whet her the m em ory chip works normally. Subtest 01 BIOS ROM This test item is to check the validity of BIOS ROM that in cludes two sub-items -- ROM Read and ROM Write Protection. RO M Read is to check whether BIOS ROM could be correctly read out, ROM Wr ite Protec[...]

3.6 Memory Test 3 Diagnostic Programs Pattern Size: Choose the pattern size – BY TE, WORD, DWORD or ALL. Percent (%): Choose the percentage of the defined range of the m emory to be tested. Time Limit(h): Choose or Input the time (hour) of the defined range of the memory to be tested. Time Limit(m): Choose or Input the time (minut e) of the defin[...]

3 Diagnostic Programs 3.6 Memory Test 42 Satellite E100 Maintenance Manual test coverage would be based on the setting and the value in ‘Percent (%) mentioned at below. Pattern Size: Choose the pattern size – BY TE, WORD, DWORD or ALL. Percent (%): Choose the percentage of the defined range of the m emory to be tested. Time Limit(h): Choose or [...]

3.6 Memory Test 3 Diagnostic Programs In addition to the above pattern test of th e memory, there is Read/Write Cycle test and Read Cycle Test for the extended memory. Below is the parameter dialog window of the extended pattern test. Test Range: Specify the test coverage range of Extended Memory. If user chooses Total Size, it means that the whole[...]

3 Diagnostic Programs 3.6 Memory Test 2. Read Cycle Test Test by using read instructions. Subtest 05 Walking 1’s Test The test item is to ensure that there is no short circuitry issue in mem ory chip. The parameter dialog window is the same as that in ‘Subtest 02 P attern’. Subtest 06 Walking 0’s Test The test item is to ensure that there i[...]

3.6 Memory Test 3 Diagnostic Programs Satellite E100 Maintenance Manual 45 2. Random Increment Read/W rite This test item is to check whether the memory could be correctly accessed with randomized memory address an d a series of increm ental data. Subtest 11 Data Bus Test This test item is to check whether the data bus works normally. Subtest 12 Me[...]

3 Diagnostic Programs 3.7 Storage 3.7 Storage Subtest 01 HDD This test item runs on IDE hard disks. It checks the functions and performance of IDE hard disk. In order to protect user’s HDD data, the password must be verified before the HDD test. The screen is as follows: Password ： hard disk 1. Sequential/Random R/W This test item is to check t[...]

3.7 Storage 3 Diagnostic Programs LBA Start, LBA End --Specify the start and end byte in LBA (Large Block Address). Percent —Specify the coverage rate in percentage of the total disk. Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested. Time Limit(m): Choose or Input the time (minute) of the defined [...]

3 Diagnostic Programs 3.7 Storage Percent-- Specify the coverage rate in percentage of the total disk. Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested; Time Limit(m): Choose or Input the time (minute) of the defined range of the total disk to be tested. 3. Performance Check the HDD’s seeking spee[...]

3.7 Storage 3 Diagnostic Programs Satellite E100 Maintenance Manual 49 Subtest 02 ODD The ODD test runs on ID E CDROM/DVD-ROM & CD-RW. It will check the ODD driver’s functionality and perf ormance. 1. Controller Test Check the CDROM controller’s status. 2. Data Transfer Rate Check the data transfer rate of the ODD dr ive. It will read data [...]

3 Diagnostic Programs 3.8 Video 3.8 Video This test item tests the video by: 1. displaying the figures in different graphic modes. 2. displaying the property and color of the characters in different text modes. User will confirm whether each video m ode works normally by judging whether the display is correct. It checks whether the video m emory wo[...]

3.8 Video 3 Diagnostic Programs It would display the below texts of th e different attributes in the screen: 1. Text in normal attribute; 2. Text in blinking normal attribute; 3. Text in inverse attribute; 4. Text in blinking inverse attribute; 5. Text in hi-intensity attribute; 6. Text in blinking hi-intensity attribute; Users need to check whethe[...]

3 Diagnostic Programs 3.8 Video 4. Text Color This test item is to check whether all 16 colors foreground and all 8 colors background works normally in VGA text mode. The bit4-6 of the attribute byte of a ch aracter defines 8 background colors (black, blue, green, cyan, red, brown, magenta, and light gray), and the bit0-3 defines 16 foreground colo[...]

3.8 Video 3 Diagnostic Programs This test item is to check whether 80*25 Text Mode works normally. In the test, user is required to respond according to the instru ction in the screen. Subtest 02 640 * 480 VGA Mode This test item is to check whethe r 680*480 VGA Text mode works normally. In the test, user is required to respond according to the ins[...]

3 Diagnostic Programs 3.8 Video Subtest 03 VESA Video Modes This test item is to check whether all the video modes supported by the video card works normally. In the test, user is required to respon d following the instruction in the screen. 1. 640X480 Video Modes Test 2. 800X600 Video Modes Test 3. 1024X768 Video Modes Test 4. 12 80 X 800 Video Mo[...]

3.8 Video 3 Diagnostic Programs If press Ctrl+Break to force the test to term inate during execution of VESA Video Memory, the test program will not operate and display properly in f urther tests. Subtest 05 AGP Test This test item is to report the system’s Accelerated Graphics Port status and check whether AGP registers works normally. Subtest 0[...]

3 Diagnostic Programs 3.8 Video Subtest 07 Register Test This test item is to check whether th e registers of the video adapter works normally. Subtest 08 Color Purity Test This test item is to check whether th e sy stem (the video adapter and the display) could display the purity color of re d, green, blue, black and white. In the test, user is re[...]

3.8 Video 3 Diagnostic Programs Subtest 10 DAC/Palette Address This test item is to check the f unction of DAC registers and Palette registers. In the test, user is required to respond according to the instru ction in the screen. Satellite E100 Maintenance Manual 57[...]

3 Diagnostic Programs 3.8 Video 58 Satellite E100 Maintenance Manual[...]

3.8 Video 3 Diagnostic Programs Satellite E100 Maintenance Manual 59 3.9 Communication (COMM) Subtest 01 LAN Card This test item is to check whether the m odule can detect the exis tence of the network card and display its related information. 1. Device ID Detection Detect the device ID of the network card. 2. Vendor ID Detection Detect the vendor [...]

3 Diagnostic Programs 3.10 Peripheral 3.10 Peripheral Subtest 01 Keyboard This test item is to check wh ether the keyboard works normally. 1. Keyboard Data Line Test Check whether the keyboard data line works normally. 2. Keyboard Clock Line Test Check whether the keyboard clock line works normally. Subtest 02 Mouse Test Check whether the point dev[...]

3.10 Peripheral 3 Diagnostic Programs Subtest 03 Led Test 1. Led Test Check whether the green and white led works normally. Satellite E100 Maintenance Manual 61[...]

3 Diagnostic Programs 3.10 Peripheral Check whether the orange led works normally. Check whether the HDD led works normally. 62 Satellite E100 Maintenance Manual[...]

3.11Error Codes and Description 3 Diagnostic Programs Satellite E100 Maintenance Manual 63 3.11 Error Codes and description The format of ‘Error Code’ is ‘ddxxee ’, and ‘dd’ is the device ID (1 ~2 chars), ‘xx’ is test function ID of device (2 chars), ‘ee’ is th e error code of device (2 chars); th e range of error code is from 0[...]

3 Diagnostic Programs 3.11Error Codes and Description 64 Satellite E100 Maintenance Manual 04 (XMS)Memory Problem The test pattern read out from the extension memory is different from the one that has been written in this address. As above. 05 (XMS) Out Of Range Wrong parameters se tup. Check and reset the parameters. 06 Address Test Error Interfer[...]

3.11Error Codes and Description 3 Diagnostic Programs Satellite E100 Maintenance Manual 65 configuration. 17 PCI to ISA Bridge Error PCI-ISA bridge errors. Repeat multiple times. If there is always the same error, replace the board. 18 ESCD Error ESCD errors. As above. 53 ACPI Table Test Error Errors with the ACPI table test. As above. 34xx FAN 01 [...]

3 Diagnostic Programs 3.11Error Codes and Description 66 Satellite E100 Maintenance Manual 15 VESA VRAM Test Error Physical problems with the video card or the monitor. Check whether there is any physical problem with the video card or the monitor. 16 AGP Test Error AGP configuration register errors. Check and see whether the AGP video card has any[...]

3.11Error Codes and Description 3 Diagnostic Programs Satellite E100 Maintenance Manual 67 01 Keyboard Map & Stroke Test Fail Keyboard Map & Stroke Test fails. Check the KBD connection and repeat the test. 03 Clock Line Test Fail Clock Line Test fails. As above. 04 Data Line Test Fail Data Line Test fails. As above. 05xx Mouse 01 Touch Pad [...]

3 Diagnostic Programs 3.11Error Codes and Description 68 Satellite E100 Maintenance Manual 09 Eject Error Wrong CD-ROM drive. Exit from the wrong drive.[...]

3.12 Quick Test Item List 3 Diagnostic Programs Satellite E100 Maintenance Manual 61 3.12 Quick Test Item List Device Test Items Comment CPU Basic Functionality N PU Basic Functions CPU Information Memory BIOS ROM Cache Me mory Bit Stuck High Test 10% or 3 minutes Bit Stuck Low Test 10% or 3 minutes Address Test Board Interval Timer Clock / Calenda[...]

Chapter 4 Replacement Procedures 4 1[...]

4 Replacement Procedures 4-ii Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual[...]

4 Replacement Procedures Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual 4-iii Chapter 4 Contents 4.1 General .................................................................................................................... ... 4-1 Safety Precautions .................................................................................[...]

4 Replacement Procedures 4-iv Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual 4.6 HDD ........................................................................................................................ . 4-21 Removing the HDD ........................................................................................... 4-21 Install[...]

4 Replacement Procedures Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual 4-v Installing the FL I nverter Board ........................................................................ 4-44 4.17 LCD Modules........................................................................................................... 4-45 Removing the LCD [...]

4 Replacement Procedures 4-vi Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual Figures Figure 4-1 Removing the battery pack ................................................................................. 4-8 Figure 4-2 Removing the battery pack ................................................................................. 4-8 Fig[...]

4 Replacement Procedures Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual 4-vii Figure 4-32 Removing the 15.1-inch LCD cable................................................................ 4-47 Figure 4-33 Removing the CCD board and MIC................................................................ 4-48 Figure 4-34 Removing Power boa[...]

Error! Style not defined. General 4 Replacement Procedures 4 1 4.1 General This chapter explains how to disassemble the computer and replace Field Replaceable Units (FRUs). Some replacement procedures m ay not require you to remove all the surrounding FRUs to replace only one FRU. The chart below shows the FRUs in the order in which they should be [...]

4 Replacement Procedures 4.1 General 4-2 Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual Safety Precautions Before you begin to disassembly read the following safety precautions carefully. Be sure to follow them while you are working. DANGER: 1. Always use the genuine batteries or replacement batteries authorized by Toshiba. Batterie[...]

Error! Style not defined. General 4 Replacement Procedures Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual 4-3 CAUTION: 1. Before replacing a component, make su re that the replacement component meets the required specifications. To avoid computer failures, never use components that do not meet the specifications. 2. To avoid interna[...]

4 Replacement Procedures 4.1 General 4-4 Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual Before You Begin Before you begin to disassembly the computer, keep in m ind the precautions and advice in this section. Always begin disassembly by removing the AC adapter and battery pack. Remove the optional parts and accessories as well. The [...]

Error! Style not defined. General 4 Replacement Procedures Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual 4-5 Disassembly Procedures The cable connectors come in these two basic types:  Pressure plate connectors  Normal pin connectors To remove a pressure plate connector, pull up the tabs on either side of the connector's[...]

4 Replacement Procedures 4.1 General 4-6 Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual Tools and Equipment For your safety and that of other people in the working environment, it is strongly recommended that you use electrostatic discharge (ESD) equipm ent. The proper use of this equipment will ensure successful repair work and red[...]

Error! Style not defined. General 4 Replacement Procedures Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual 4-7 Colors of Screw Shanks For easy identification of the correct screws, the screw shanks are colored according to their lengths, as follows:  Screws of an even-numbered length Brown  Screws of an odd-numbered length W hi[...]

4 Replacement Procedures 4.1 General Removing the Battery Pack Remove the battery pack according to the following procedures and Figure 4-1, 4-2. CAUTION: When handling the battery packs, use care not to short circuit the terminals. Do not drop, hit, twist, or bend the battery packs. Do not scratch or break up their casing. 1. Turn the computer ups[...]

Error! Style not defined. General 4 Replacement Procedures Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual 4-9 Installing the Battery Pack Install the battery pack according to the following procedures and Figure 4-1, 4-2. CAUTION: The battery packs contain a lithium ion battery, which can explode due to improper replacement, use, ha[...]

4 Replacement Procedures 4.1 General Removing the Optional PC Card Remove the optional PC card according to the following procedures and Figure 4-3, after checking that the computer is turned off in boot mode. CAUTION: Install or remove the PC card correctly, according the manuals for the PC card and the operating system you are using. 1. Push the [...]

Error! Style not defined. General 4 Replacement Procedures Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual 4-11 Installing the Optional PC Card Install the optional PC card according to the following procedures and Figure 4-3, after checking that the computer is turned off in boot mode. 1. Insert the PC card gently until it stops and[...]

4 Replacement Procedures 4.1 General Removing the Memory Card Remove the mem ory card according to the following procedures and Figure 4-4, after checking that the computer is turned off in boot mode. 1. Push the memory card to be rem oved until it stops then release the memory card. 2. When the mem ory card pops out, grasp it and pull it out. Memo[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 4.2 Key board Cover and Keyboard Removing the Keyboard Cover and Keyboard Remove the Keyboard Cover and Keyboard according to the following procedures and Figure 4-5, 4-6. 1. Release the following 13 latches on the keyboard cover, in that order: - Five bottom latches. - Si[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4-14 Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual Installing the Keyboard Cover and Keyboard Install the Keyboard cover and keyboard according to the following procedures and Figure 4- 5, 4-6. 1. Connect the keyboard cable to CN6 and CN8 on the system boa[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 4.3 Optional Memory Removing the Optional Memory Remove the optional mem ory (module) according to the following procedures and Figures 4- 7, after checking that the computer is turned off in boot mode. CAUTION: Remove the optional memory after turning off the computer. If[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4-16 Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual Installing the Optional Memory Install the optional memory (m odule) according to the following procedures and Figures 4-7, after checking that the computer is turned off in boot mode. Note: The slot A is [...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 4.4 UWB Module Removing the UWB Module Remove the UWB Module according to the following procedures and Figures 4-8, after checking that the computer is turned off in boot mode. 1. Remove the two M2x4 black flat-head screws securing the UWB m odule. 2. Remove the UWB m odul[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4-18 Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual Installing the UWB Module Install the UWB module according to the following procedures and Figures 4-8, after checking that the computer is turned off in boot mode. 1. Insert the UWB module in to the conne[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 4.5 Top Cover Removing the Top Cover Remove the top cover according to the following procedures and Figures 4-9 and 4-10. 1. Turn the computer upside down and remove the following fifteen screws in the order shown on figure4-9. - Six M2.5x7 black flat head screws. - One M2[...]

4 Replacement Procedures 4.5 Top cover 4-20 Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual 2. Restore the normal computer placem ent. 3. Disconnect the touch pad board flat cable from CN25, Finger print cable from CN51 MMB board flat cable from CN18, Power boa rd flat cable from CN9 and Bluetooth card cable from CN27. 4. Remove the [...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 4.6 HDD Removing the HDD CAUTION: Do not press on the top or bottom of the drive. Applying such pressure can either corrupt the data in the drive or damage the drive. Remove the HDD (hard disk drive) according to the following procedures and Figures 4-11, 4-12. 1. Release [...]

4 Replacement Procedures 4.6 Error! Style not defined. 5. Remove the HDD connector M3x3 5 black flat head screw . M3x3 5 black flat head screw . HDD pack HDD connector HDD chassis Figure 4-12 Removing the HDD chassis CAUTION: Do not apply pressure to the top or bottom of the drive. 4-22 Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual 4-23 Installing the HDD Install the HDD according to the following procedures and Figures 4-11, 4-12. CAUTION: To avoid damage, always hold the HDD only by its sides. 1. Attach the HDD chassis. 2. Secure the HD[...]

4 Replacement Procedures 4.7 Error! Style not defined. 4.7 ODD Bay Module Removing the ODD Bay Module NOTE: The installation and removal procedures are the same for all the modules that can be installed in the ODD bay. See the appropriate sections for the disassembly procedures of specific modules. Remove the ODD bay module according to the followi[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Disassembling the ODD Drive NOTE: Do not disassemble the ODD drive when it is working normally. Disassemble or replace the ODD drive only if it fails. Disassemble the ODD drive according to the following procedures and Figure 4-14. 1. Remove two M2x4 black flat head screws[...]

4 Replacement Procedures Error! Style not defined. Display Assembly 4.8 Display Assembly Removing the Display Assembly CAUTION: Use care to avoid that the antenna cable is not caught between the display assembly and computer. Remove the display assembly according to the following procedures and Figures 4-15, 4-16. 1. Remove two M2.5x6 black flat he[...]

4.8 Error! Style not defined. 4 Replacement Procedures CN12 CN7 CN10 LCD FL cable CCD cable MIC cable Wireless Lan antenna M2 5x4 black flat head screw . T APE Cable fillister Cable fillister Figure 4-16 Removing the display assembly Installing the Display Assembly Install the display assembly according to the following procedures and Figures 4-15,[...]

4 Replacement Procedures Error! Style not defined. FAN 4.9 FAN Removing the FAN Remove the FAN according to the following procedures and Figures 4-17. 1. Disconnect the FAN cable from CN2. FA N CN2 M2x5 white flat head screw Figure 4-17 Removing the FAN 2. Remove three M2x5 white flat head screws on the FAN 3. Remove the FAN. Installing the FAN Ins[...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 4.10 CPU Cooling Module CAUTION: When removing the cooling module, keep the following in mind: The cooling module can become very hot during operation. Be sure to let it cool down before starting the repair work. Do not touch or cause damage to the fan in the cooling modul[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. Figure 4-19 Applying silicon grease 1. If the thermal pad is broken, replace new thermal pad into correct position, therm al pad part number is V000934150. Figure 4-20 Replace new thermal pad into correct position. 2. Tear down the tap on the thermal pad. Figure 4-21 Tear [...]

Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual 4-31 Install the cooling Module according to the following procedures and Figures 4-18, 4-19, 4- 20, 4-21. CAUTION: When installing the cooling module, keep the following in mind: 1. Be sure to confirm the corr[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4.11 CPU Removing the CPU Remove the CPU according to the following procedures and Figures 4-22, 4-23 and 4-24. CAUTION: When removing the CPU, keep the following in mind: The CPU can become very hot during operation. Be sure to let it cool down before starting repair work[...]

4.11 CPU 4 Replacement Procedures Installing the CPU Install the CPU according to the following procedures and Figures 4-22, 4-23, 4-24. 1. Check that the triangle on the cam is in the unlock position. 2. Attach the CPU to the correct position in the CPU socket. Align the CPU with the CPU socket by using the triangle as a guide. 3. Secure the CPU b[...]

4 Replacement Procedures Error! Style not defined. Error! Style not defined. Figure 4-24 Securing the CPU 4-34 Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual[...]

4.12 Speakers and Wireless LAN 4 Replacement Procedures 4.12 Speakers and Wireless LAN Removing the Speakers and Wireless LAN. Remove the Speakers and Wireless LAN according to the following procedures and Figure 4-25. 1. Disconnect the left speaker cable from CN26 and right speaker from CN29. 2. Remove two M2x4 black flat head screws securing the [...]

4 Replacement Procedures 4.12 Speakers and Wireless LAN 4-36 Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual Installing the Speakers and Wireless LAN Install the speakers and Wireless LAN according to the following procedures and Figure 4- 25. 1. Seat the left and right speaker in the correct position. 2. Secure the left and right sp[...]

4.13 System board 4 Replacement Procedures 4.13 System Board Removing the System Board. NOTE: Be careful of the eject button for the PC card. It can be damaged when removing the board. Make sure it is securely installed. Remove the System Board according to the following procedures and Figure 4-26. 1. Release four M2.5x4 white flat head screws on t[...]

4 Replacement Procedures 4.13 System board 4-38 Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual Installing the System Board Install the System Board according to the following procedures and figure 4-26. NOTE: Be careful of the eject button for the PC card. It can be damaged when installing the system board. Make sure it is pushed in[...]

4.14 USB board, DC-IN FM card and RGB cable 4 Replacement Procedures 4.14 USB board, DC-IN, FM card and CRT cable Removing the USB board, DC-IN, FM card and CRT cable. Remove the USB board, DC-IN, FM card and CRT cable according to the following procedures and Figures 4-27. 1. Release one M2x4 black flat head screw securing the USB cable. 2. Remove[...]

4 Replacement Procedures 4.14 USB board, DC-IN FM card and RGB cable 4-40 Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual Installing the USB board, DC-IN, FM card and CRT cable Install the USB board, DC-IN, FM card and CRT cable according to the following procedures and Figure 4-27. Note: Be careful of the kill switch button for the [...]

4.15 Display Mask 4 Replacement Procedures 4.15 Display Mask Removing the Display Mask Remove the display mask according to the following procedures and Figure 4-28. 1. Remove the following 4 seals on the display module in that order: - Two gray seals on the bottom - Two gray seals on the top 2. Remove the following 4 screws on the display module, [...]

4 Replacement Procedures 4.15 Display Mask 4-42 Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual Installing the Display Mask Install the display mask according to the following procedures and Figure 4-28. 1. Seat the display mask in the correct position and secure the following 19 latches, in that order: - Four latches on the left sid[...]

4.16 FL Inverter Board 4 Replacement Procedures 4.16 FL Inverter Board Removing the FL Inverter Board Remove the FL inverter board according to the following procedures and Figures 4-29. 1. Remove one M2.5x5 black flat head screw securing the inverter board. 1. Lift the LCD module, FL inverter board and disconnect the LCD/FL cable from the LCD/FL c[...]

4 Replacement Procedures 4.16 FL Inverter Board 4-44 Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual Installing the FL Inverter Board Install the FL inverter board according to the following procedures and Figures 4-29. 1. Connect the LCD/FL cable to LCD/FL connector, and connect the HV cable to the HV connector. 2. Seat the LCD modu[...]

4.17 LCD Module 4 Replacement Procedure s Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual 4-45 4.17 LCD Modules NOTE: ICs are fragile. Use extreme care not to apply pressure to the ICs along the edges of the LCD module. NOTE: Dispose of used LCD panels (fluorescent (FL) tubes) as required by local ordinances or regulations. NOTE: The[...]

4 Replacement Procedures 4.17 LCD Module M2 5x5 black flat head screw . Figure 4-30 Removing the 15.1-inch LCD module and screws LCD module M2 5x5 black flat head screw . Right LCD bracket Left LCD bracket M2x3 black flat head screw M2x3 black flat head screw Figure 4-31 Removing the 15.1-inch LCD module 4-46 Satellite E100/E105/ Satellite ProE100/[...]

4.17 LCD Module 4 Replacement Procedure s Figure 4-32 Removing the 15.4-inch LCD cable Installing the 15.1-inch LCD Module NOTE: LCD/FL cable must be carefully peeled away before disconnecting it from the module. Install the 15.1-inch LCD module according to the following procedures and Figures 4-30, 4-31, 4-32. 1. Turn the LCD upside down. 2. Conn[...]

[...]

4.18 CCD Board and MIC 4 Replacement Procedure s 4.18 CCD Board and MIC Removing the CCD Board and MIC Remove the FL inverter board according to the following procedures and Figure 4-33. 1. Disconnect the CCD cable from the CCD module connector and rem ove the CCD board. 2. Lift the MIC from the display rear cover. CCD board MIC CCD board cable Fig[...]

4 Replacement Procedures 4.18 CCD Board and MIC Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual 4-49 Installing the CCD Board and MIC Install the FL inverter board according to the following procedures and Figure 4-33. 1. Connect the CCD module cable to CCD module connector. 2. Seat the CCD module, MIC in the correct position.[...]

4.19 Power board, Switch board, Touch Pad board 4 Replacement Procedure s 4-50 Satellite E100/E105/ Satellite ProE100/E105 Maintenance Manual 4.19 Power board, Bluetooth card, Button board and Finger print board. Removing the Power board, Bluetooth card, Button board and Finger print board. Remove the Power board, Bluetooth card, Button board and F[...]

4 Replacement Procedures 4.19 Power board, Switch board, Touch Pad board Power board M2x3 black flat head screw MMB board MMB board flat cable Finger print board Bluetooth board Bluetooth board cable J1 CN2004 CN2005 Button board T ouch pad bracket M1 6x2 5 white flat head screw .. T ouch pad flat cable Button board flat cable M2x3 black flat head [...]

6000 1 次 Appendices[...]

Appendices App-ii Satellite E100/E105 Maintenance Manual Appendix Contents Appendix A Handling the LCD Module .......................................................................... A-1 Appendix B Board Layout ................................................................................................. B-1 B.1 System Board Front View .......[...]

Appendices Satellite E100/E105 Maintenance Manual App-iii C.24 CN25 MB to Touch Pad Board Connector (8-Pin) .................................... C-12 C.25 CN26 Internal Speaker Left Connector (2-Pin) ......................................... C-12 C.26 CN27 Blue Tooth Module Connector (10-Pin) .......................................... C-12 C.27 CN2[...]

Apx. A Handling the LCD Module Appendices Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assem bly or disassembly. Observe the following precautions when handling the LCD module: 1. When installing the LCD module in the LCD c over, be sure to seat it so that it is pr[...]

Appendices Apx. A Handling the LCD Module 3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to a cloth and then wipe the panel’s surface. Do [...]

Apx. A Handling the LCD Module Appendices 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module. Satellite E10[...]

Appendices Apx. A Handling the LCD Module 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. A-4 Satellite E100/E105 Maintenance Manual[...]

Apx. A Handling the LCD Module Appendices 9. Do not disassemble the LCD module. Disassem bly can cause malfunctions. 10. If you transport the module, do not use pack ing m aterial that contains epoxy resin (amine) or silicon glue (alcohol or oxide). These materials can release gas that can damage the panel’s polarization. Satellite E100/E105 Main[...]

Apx. B Board Layout Appendices Appendix B Appendix B Board Layout B.1 System Board Front View Figure B-1 Board Layout (Front) Satellite E100/E105 Maintenance Manual B-1[...]

Appendices Apx. B Board Layout B.2 System Board Back View Figure B-2 Board Layout (Back) B-2 Satellite E100/E105 Maintenance Manual[...]

Appendices Apx. C Pin Assignments Satellite E100/E105 Maintenance Manual C-1 Appendix C C.1 CN1 Battery Pack Connector (9-Pin) ......................................................... C-3 C.2 CN2 FAN Connector (3-Pin) ..................................................................... C-3 C.3 CN3 MB to CRT Board Connector (14-Pin) ..............[...]

Appendices Apx. C Pin Assignments C-2 Satellite E100/E105 Maintenance Manual C.32 JACK1 RJ45 LAN Connector (12-Pin) ........................................................C-19 C.33 JACK2 External MIC Connector (6-Pin) ......................................................C-19 C.34 JACK3 Head Phone Connector (6-Pin) ................................[...]

Appendices Apx. C Pin Assignments Satellite E100/E105 Maintenance Manual C-3 Appendix C Appendix C Pin Assignments System Board C.1 CN1 Battery Pack Connector (9-Pin) Table C-1 Battery Pack Connector Pin Assignments (9-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 BATT+ O 2 B ATT+ O 3 ID O 4 DGND - 5 TS I 6 SMD I/O 7 SMC I/O 8 DGND - 9 DGN[...]

Appendices Apx. C Pin Assignments C-4 Satellite E100/E105 Maintenance Manual C.4 CN4 Robson Card Module Connector (52-Pin) Table C-4 Robson Card Module Connector Pin Assignments (52-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 PCIE_WAKE# I/O 2 +V3S O 3 CH_DATA I/O 4 DGND - 5 CH_CLK I/O 6 +V1.5S O 7 CLKREQ_R_ROBSON# I 8 LPC_3S_FRAME# O 9 D[...]

Appendices Apx. C Pin Assignments Satellite E100/E105 Maintenance Manual C-5 1 DGND - 2 - - 3 - - 4 +V5S O C.6 CN6 AC-In Cable Connector (4-Pin) Table C-6 AC-In Cable Connector Pin Assignments (4-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 +VADPTR - 2 +VADPTR - 3 DGND - 4 DGND - C.7 CN7 Internal MIC Connector (2-Pin) Table C-7 Internal M[...]

Appendices Apx. C Pin Assignments C-6 Satellite E100/E105 Maintenance Manual 29 +V3S O 30 - - 31 - - 32 DGND - 33 - - 34 +V3S O C.9 CN9 Power Board Connector (4-Pin) Table C-9 Power Board Connector Pin Assignments (4-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 DGND - 2 PWRBTN_LED O 3 PWR_SWIN#_3 I 4 +V5S - C.10 CN10 Camera Cable Connecto[...]

Appendices Apx. C Pin Assignments Satellite E100/E105 Maintenance Manual C-7 9 LVDS_TXDL0P O 10 LVDS_TXDL1P O 11 LVDS_TXDL2N O 12 LVDS_TXCLN O 13 LVDS_TXDL2P O 14 LVDS_TXCLP O 15 DGND - 16 DGND - 17 LVDS_TXDU0N O 18 LVDS_TXDU1N O 19 LVDS_TXDU0P O 20 LVDS_TXDU1P O 21 LVDS_TXDU2N O 22 LVDS_TXCUN O 23 LVDS_TXDU2P O 24 LVDS_TXCUP O 25 DGND - 26 DGND - [...]

Appendices Apx. C Pin Assignments C-8 Satellite E100/E105 Maintenance Manual Pin No. Signal Name I/O Pin No. Signal Name I/O 1 DGND - 2 SATA_C_TXP5 O 3 SATA_C_TXN5 O 4 DGND - 5 SATA_C_RXN5 I 6 SATA_C_RXP5 I 7 DGND - 8 - - 9 +V5S O 10 +V5S O 11 - - 12 DGND - 13 DGND - - - - C.15 CN16 1394 Connector (4-Pin) Table C-15 1394 Connector Pin Assignments ([...]

Appendices Apx. C Pin Assignments Satellite E100/E105 Maintenance Manual C-9 C.18 CN19 5 In 1 Card Connector (40-Pin) Table C-18 5 In 1 Card Connector Pin Assignments (40-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 MDIO00 I/O 2 MDIO03 I/O 3 VCC_MC O 4 MDIO17 I/O 5 MDIO16 I/O 6 MDIO15 I/O 7 MDIO14 I/O 8 MDIO13 I/O 9 MDIO12 I/O 10 MDIO11 I[...]

Appendices Apx. C Pin Assignments C-10 Satellite E100/E105 Maintenance Manual C.20 CN21 SATA HDD Connector (22-Pin) Table C-20 SATA HDD Connector Pin Assignments (22-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 DGND - 2 SATA_C_TXP0 O 3 SATA_C_TXN0 O 4 DGND - 5 SATA_C_RXN0 I 6 SATA_C_RXP0 I 7 DGND - 8 - - 9 - - 10 - - 11 DGND - 12 DGND - 1[...]

Appendices Apx. C Pin Assignments Satellite E100/E105 Maintenance Manual C-11 29 DGND - 30 ICH_3A_ALERT_CLK I/O 31 PCIE_C_TXN_WLAN O 32 ICH_3A_ALERT_DAT I/O 33 PCIE_C_TXP_WLAN O 34 DGND - 35 DGND - 36 USB_P5N I/O 37 - - 38 USB_P5P I/O 39 - - 40 DGND - 41 - - 42 WIMAX_3G_LED# I 43 DGND - 44 - - 45 - - 46 - - 47 - - 48 +V1.5S O 49 - - 50 DGND - 51 PC[...]

Appendices Apx. C Pin Assignments C-12 Satellite E100/E105 Maintenance Manual Pin No. Signal Name I/O Pin No. Signal Name I/O 1 USB_VCC1 O 2 USB_L_P1N I/O 3 USB_L_P1P I/O 4 DGND - C.24 CN25 MB to Touch Pad Board Connector (8-Pin) Table C-24 MB to Touch Pad Board Connector Pin Assignments (8-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 LID[...]

Appendices Apx. C Pin Assignments Satellite E100/E105 Maintenance Manual C-13 3 USB_P8N I/O 4 +V3S O C.28 CN29 Internal Speaker Right Connector (2-Pin) Table C-28 Internal Speaker Right Connector Pin Assignments (2-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 SPK_OUT_R+ O 2 SPK_OUT_R- O C.29 CN47 DDR2 DIMM0 Connector (200-Pin) Table C-29 [...]

Appendices Apx. C Pin Assignments C-14 Satellite E100/E105 Maintenance Manual 45 MA_DATA(17) I/O 46 MA_DATA(21) I/O 47 DGND - 48 DGND - 49 MA_DQS#(2) I/O 50 - - 51 MA_DQS(2) I/O 52 MA_DM(2) O 53 DGND - 54 DGND - 55 MA_DATA(18) I/O 56 MA_DATA(22) I/O 57 MA_DATA(19) I/O 58 MA_DATA(23) I/O 59 DGND - 60 DGND - 61 MA_DATA(24) I/O 62 MA_DATA(28) I/O 63 M[...]

Appendices Apx. C Pin Assignments Satellite E100/E105 Maintenance Manual C-15 115 MA_CS1# O 116 MA_A(13) O 117 +V1.8 O 118 +V1.8 O 119 MA_ODT1 O 120 MA_CS3# O 121 DGND - 122 DGND - 123 MA_DATA(32) I/O 124 MA_DATA(36) I/O 125 MA_DATA(33) I/O 126 MA_DATA(37) I/O 127 DGND - 128 DGND - 129 MA_DQS#(4) I/O 130 MA_DM(4) I/O 131 MA_DQS(4) I/O 132 DGND - 13[...]

Appendices Apx. C Pin Assignments C-16 Satellite E100/E105 Maintenance Manual 185 MA_DM(7) O 186 MA_DQS#(7) I/O 187 DGND - 188 MA_DQS(7) I/O 189 MA_DATA(58) I/O 190 DGND - 191 MA_DATA(59) I/O 192 MA_DATA(62) I/O 193 DGND - 194 MA_DATA(63) I/O 195 SB_3S_SMDATA I/O 196 DGND - 197 SB_3S_SMCLK I/O 198 N$860954 - 199 +V3S O 200 N$861284 - C.30 CN51 DDR2[...]

Appendices Apx. C Pin Assignments Satellite E100/E105 Maintenance Manual C-17 45 MB_DATA(17) I/O 46 MB_DATA(21) I/O 47 DGND - 48 DGND - 49 MB_DQS#(2) I/O 50 - - 51 MB_DQS(2) I/O 52 MB_DM(2) O 53 DGND - 54 DGND - 55 MB_DATA(18) I/O 56 MB_DATA(22) I/O 57 MB_DATA(19) I/O 58 MB_DATA(23) I/O 59 DGND - 60 DGND - 61 MB_DATA(24) I/O 62 MB_DATA(28) I/O 63 M[...]

Appendices Apx. C Pin Assignments C-18 Satellite E100/E105 Maintenance Manual 115 MB_CS1# O 116 MB_A(13) O 117 +V1.8 O 118 +V1.8 O 119 MB_ODT1 O 120 MB_CS3# O 121 DGND - 122 DGND - 123 MB_DATA(32) I/O 124 MB_DATA(36) I/O 125 MB_DATA(33) I/O 126 MB_DATA(37) I/O 127 DGND - 128 DGND - 129 MB_DQS#(4) I/O 130 MB_DM(4) I/O 131 MB_DQS(4) I/O 132 DGND - 13[...]

Appendices Apx. C Pin Assignments Satellite E100/E105 Maintenance Manual C-19 185 MB_DM(7) O 186 MB_DQS#(7) I/O 187 DGND - 188 MB_DQS(7) I/O 189 MB_DATA(58) I/O 190 DGND - 191 MB_DATA(59) I/O 192 MB_DATA(62) I/O 193 DGND - 194 MB_DATA(63) I/O 195 SB_3S_SMDATA I/O 196 DGND - 197 SB_3S_SMCLK I/O 198 N$860610 - 199 +V3S O 200 N$860611 - C.31 CN500 SIM[...]

Appendices Apx. C Pin Assignments C-20 Satellite E100/E105 Maintenance Manual 5 DGND - 6 - - C.34 JACK3 Head Phone Connector (6-Pin) Table C-34 Head Phone Connector Pin Assignments (6-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 DGND - 2 HP_R_JACK O 3 HP_L_JACK O 4 HPS_JACK I 5 DGND - 6 - - CRT Board C.35 CN2000 CRT Board Connector (15-Pi[...]

Appendices Apx. C Pin Assignments Satellite E100/E105 Maintenance Manual C-21 11 G O 12 DGND - 13 R O 14 +V5S_RGB O 15 - - - - - FM Tuner Board C.37 CN2002 FM Antenna Connector (2-Pin) Table C-37 FM Antenna Connector Pin Assignments (2-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 FM_ANT I 2 DGND - C.38 CN2003 FM Tuner Board Connector (8-P[...]

Appendices Apx. C Pin Assignments C-22 Satellite E100/E105 Maintenance Manual C.40 CN2005 Touch Pad Board Connector (8-Pin) Table C-40 Touch Pad Board Connector Pin Assignments (8-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 GND_TP - 2 DB_TP_LED_ON I 3 TP_IM_CLK_5 I/O 4 TP_IM_DAT_5 I/O 5 - - 6 +TP_5S O 7 +V3LA_TP O 8 LID_SW#_3_TP O[...]

Apx. D Keyboard Scan/Character Codes Appendices Satellite E100/E105 Maintenance Manual D-1 Apx. D Keyboard S c an/Character Codes Appendix D Keyboard Scan/Character Codes Table D-1 Scan Codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 01 ‘ ~ 29 A9 0E F0 0E 02 1 ! 02 82 16 F0 16 03 2 @ 03 83 1E F0 1E 04[...]

Appendices Apx. D Keyboard Scan/Character Codes D-2 Satellite E100/E105 Ma intenance Manual Table D-1 Scan Codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 29 | 2B AB 5D F0 5D *5 30 Caps Lock 3A BA 58 F0 58 31 A 1E 9E 1C F0 1C 32 S 1F 9F 1B F0 1B 33 D 20 A0 23 F0 23 34 F 21 A1 2B F0 2B 35 G 22 A2 34 F0[...]

Apx. D Keyboard Scan/Character Codes Appendices Satellite E100/E105 Maintenance Manual D-3 Table D-1 Scan Codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 58 Ctrl 1D 9D 14 F0 14 *3 60 Alt (L) 38 B8 11 F0 11 *3 61 Space 39 B9 29 F0 29 62 ALT (R) E0 38 E0 B8 E0 11 E0 F0 11 75 Ins E0 52 E0 D2 E0 70 E0 F0 70[...]

Appendices Apx. D Keyboard Scan/Character Codes D-4 Satellite E100/E105 Ma intenance Manual Table D-1 Scan Codes (set 1 and set 2) (4/4) Cap Code set 1 Code set 2 No. Keytop Make Break Make Break Note 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 7 F0 7 *3 124 PrintSc *6 *6 *6 *6 *6 126 Pause *7 *7 *7 *7 *7 202 Fn — — — — *4 203 Win E0 5B E0 DB E[...]

Apx. D Keyboard Scan/Character Codes Appendices Satellite E100/E105 Maintenance Manual D-5 Table D-2 Scan Codes with left Shift key Code set 1 Code set 2 Cap No. Key top Make Break Make Break 5 5 / E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12 7 5 I N S E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0 12 7 6 DE L E0 AA E0 53 E0 D3 E0 2A E[...]

Appendices Apx. D Keyboard Scan/Character Codes D-6 Satellite E100/E105 Ma intenance Manual Table D-3 Scan Codes in Numlock mode Code set 1 Code set 2 Cap No. Key top Make Break Make Brea k 7 5 I N S E0 2A E0 52 E0 D2 E0 AA E0 12 E0 70 E0 F0 70 E0 F0 12 7 6 DE L E0 2A E0 53 E0 D3 E0 AA E0 12 E0 71 E0 F0 71 E0 F0 12 79 ← E0 2A E0 4B E0 CB E0 AA E0[...]

Apx. D Keyboard Scan/Character Codes Appendices Satellite E100/E105 Maintenance Manual D-7 Table D-5 Scan Codes in overlay mode Code set 1 Code set 2 Cap No. Keytop Make Break Make Break 08 7 (7) 47 C7 6C F0 6C 09 8 (8) 48 C8 75 F0 75 10 9 (9) 49 C9 7D F0 7D 11 0 (*) 37 B7 7C F0 7C 23 U (4) 4B CB 6B F0 6B 24 I (5) 4C CC 73 F0 73 25 O (6) 4D CD 74 F[...]

Appendices Apx. D Keyboard Scan/Character Codes D-8 Satellite E100/E105 Ma intenance Manual Table D-7 No.126 key scan code Code set 1 Code set 2 Key top Shift Make Make Pause C omm on * E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14 F0 77 Ctrl* E0 46 E0 C6 E0 7E E0 F0 7E *: This key generates only make codes.[...]

Apx. E Key Layout Appendices Apx. E Appendix E Key Layout E.1 United States (US) Keyboard Figure E-1 United Status Keyboard E.2 French Canadian (Bilingual) Keyboard Figure E-2 French Canadian Keyboard Satellite E100/E105 Maintenance Manual E-1[...]