United States Stove 6110 manuale d’uso

USSC 1 Please read this entire manual before installation and use of this appliance. Failure to follow these instructions could result in property damage, bodily injury, or even death. Contact your local building or fire officials about restrictions and installation inspection requirements in your area. Save these instructions. Ì Ì Ì Owner’s M[...]

2 USSC T ABLE OF CONTENTS .............................................................................................. 2 SAFETY PRECAUTIONS ........................................................................................... 3 SPECIFICA TIONS ..................................................................................................[...]

USSC 3 Safety Precautions IMPORT ANT : Read this entire manual before installing and operating this product. Failure to do so may result in property damage, bodily injury , or even death. Proper installation of this furnace is crucial for safe and efficient operation. Install vent at clearances specified by the vent manufacturer . Do not connect th[...]

4 USSC Specifications Heat Output 1 50,000 to 75,000 BTU/hr . Heating Capacity 2 800 - 2,000 sq. ft. Fuel Burn Rate 3 2.0 - 6.0 lbs./hr . Burn T ime (lowest setting) 125 hours continuous Hopper Capacity 250 lbs Heating S pecifications Height 47 in. Width 25-1/2 in. Depth 35-1/2 in. Weight 350 lbs. Dimensions 1 BTU output will vary depending on the [...]

USSC 5 Fuel Considerations SHELLED CORN (Dry , preferably corn with 1 1% or less moisture content) • • • • • • • Optimum moisture content of corn should be 1 1% or less. Wet corn will rapidly deteriorate furnace components, reduce efficiency and void all warranties. Purchase a moisture tester if in doubt. Corn must be clean and free f[...]

6 USSC INST ALLA TION OPTIONS Read this entire manual before you inst all and use your Multi-Fuel Furnace. Failure to follow instructions may result in property damage, bodily injury , or even death! (See specific inst allation det ails for clearances and other inst allation requirements) As a Primary Furnace —the unit functions independently of [...]

USSC 7 Installation CLEARANCES NOTE: Distance on the left-hand side of y our Multi-Fuel Furnace is set at 24 inches for suitable access to the control panel and for fuel loading. This distance may be less, but not less than 7 inches.[...]

8 USSC Installation VENTING REQUIREMENTS Inst all vent at clearances specified by the vent manufacturer . Do not connect the pellet vent to a vent serving any other appliance or furnace. Do not inst all a flue damper in the exhaust venting system of this unit. The following installation guidelines must be followed to ensure conformity with both the[...]

USSC 9 Installation VENT TERMINA TION CLEARANCES: A ----- Minimum 4-foot clearance below or beside any door or window that opens. B ----- Minimum 1-foot clearance above any door or window that opens. C ----- Minimum 3-foot clearance from any adjacent building. D ----- Minimum 7-foot clearance from any grade when adjacent to public walkways. E -----[...]

10 USSC Installation THROUGH THE W ALL INST ALLA TION (RECOMMENDED INST ALLA TION) T o vent the unit through the wall, connect the pipe adapter to the exhaust motor adapter . If the exhaust adapter is at least 18-inches above ground level, a straight section of pellet vent pipe can be used through the wall. Y our furnace dealer should be able to pr[...]

USSC 11 Installation PRIMAR Y FURNACE SECONDAR Y (ADD-ON) FURNACE When installed as a seondary furnace, a Duct Damper must be installed between the air discharge of the Pellet furnace and the primary (Gas, Electric, etc.). Damper must be a mechanical (spring return) style damper with a simple closure switch to determine if damper is opened or close[...]

12 USSC Do not operate your furnace with the viewing door open. The auger will not feed fuel under these circumst ances and a safety concern may arise from sp arks or fumes entering the room. A working smoke detector must be inst alled in the same room as this product. Hopper Lid must be closed during operation. The auger will not feed fuel if the [...]

USSC 13 Heat Range Room Fan Draft Fan Aux. Auto Manual CONTROL PANEL T urning the furnace OFF/ON, as well as adjustments for the fuel feed rate and room fan speed are performed by pressing the appropriate button(s) on the control panel which is located on the lower lef t-hand side of your American Harvest furnace. This unit can be changed between a[...]

14 USSC SHUT DOWN PROCEDURE Press the “OFF” button on the control p anel to put the furnace in shut down mode. At this time, the red light above the “OFF” button will illuminate. Once this is done, the auger will stop feeding fuel, but the room air fan(s) and draft fan will continue to operate. When the internal temperature of the unit drop[...]

USSC 15 Maintenance Operation DAIL Y OPERA TION The hopper and furnace top will be hot during operation; therefore, you should always use some type of hand protection when refueling your furnace. Never place your hand near the auger while the furnace is in operation. In the event of a power out age , the furnace WILL NOT function. It is very import[...]

16 USSC INTERIOR CHAMBERS Remove the two(2) cleanout plates on each side of the damper control. Using the cleaning tools provided, clean all ash and fue l matter from the burn chamber . This may need to be done daily depending on fuel consumption. Periodically remove and clean the burnpot and the area inside the burnpot housing. In particular it is[...]

USSC 17 6100 Parts Diagram[...]

18 USSC 6100 Parts List 1 5 9 8 10 12 7 4 6 11 3 2 Item Part No. Title Qt y . 1 25507 Feed Door 1 2 25492 Handle, Door 1 3 83506 3/8 x 1 1/4 Roll Pin 1 4 891053 Door Glass w/o Logo 1 5 88066 5/8” Rope Gasket 4.5 ft 6 88087 Glass Gasket (1 x 1 3/16) 3 ft 7 25520 Bottom Glass Ret ainer 1 8 25521 T op Glass Retainer 1 6100/61 10 P ARTS LIST Item Par[...]

USSC 19 6110 Parts Diagram[...]

20 USSC 6110 Parts List[...]

USSC 21 Wiring Diagram[...]

22 USSC T rouble Shooting PROBLEM CAUSE: Not enough combustion air; Fuel has too much moisture. Viewing window becoming black shortly af ter start-up. • Adjust the air damper to a more open position. • Use a fuel with less moisture content PROBLEM CAUSE: Not enough combustion air; Fuel has too much moisture. “Black Popcorn” is present in th[...]

USSC 23 Err or Codes Below is a chart describing the Error Codes that might be displayed if an error occurs with your furnace. Error Code Err1 Err2 Err3 Err4 Err5 Err6 Err7 Err8 Error Descrption The high limit temperature sensor has tripped. Furnace ran out of fuel during normal operation. The furnace was unable to reach the Room Fan On temperature[...]

24 USSC THIS MANUAL WILL HELP YOU OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM YOUR KING OR ASHLEY, AND ENABLE YOU TO ORDER REPAIR PARTS CORRECTLY. KEEP THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE. WHEN WRITING, ALWAYS GIVE THE FULL MODEL NUMBER WHICH IS ON THE NAMEPLATE ATTACHED TO THE HEATER. WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWIN[...]