Vermont Casting 33LDVR manuale d’uso

Installation Instructions and Homeowner ’ s Manual 10007317 12/06 Rev . 7 Builder Rear V ent Direct V ent Models: 33LDVR, 36LDVR, 39LDVR, 43LDVR DO NOT ST ORE OR USE GASOLINE OR OTHER FLAMMABLE V APORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. WHA T TO DO IF YOU SMELL GAS: • Do not try to light any appliance. • Do not touch [...]

2 LDVR Series Direct Vent Gas Fireplace 10007317 PLEASE READ THE INST ALLA TION & OPERA TING INSTRUCTIONS BEFORE USING APPLIANCE. Thank you and congratulations on your purchase of a CFM Corporation fireplace. IMPORT ANT : Read all instructions and warnings carefully before starting installation. Failure to follow these instructions fully may r[...]

3 LDVR Series Direct Vent Gas Fireplace 10007317 This gas appliance should be installed by a qualified installer in accordance with local building codes and with current CSA-B149.1 Installation codes for Gas Burning Appliances and Equipment. For USA Installations follow local codes and/or the current National Fuel Gas Code. ANSI Z223.1/NFP A 54. I[...]

4 LDVR Series Direct Vent Gas Fireplace 10007317 Fireplace Dimensions F V - Rough Opening Width Rough Opening Height Rough Opening Depth S S U T R E I H J D A Q B K L G M O Gas Line Access Gas Line Access Low V oltage Electrical Access Electrical Access C   Centerline of 7" Collar M N P Low V oltage Access Fig. 2 Fireplace specification[...]

5 LDVR Series Direct Vent Gas Fireplace 10007317 T op of Unit to Ceiling ............................. 36” (914mm) Appliance T op ....................................................... 0” (0 mm) Bottom .................................................. 0” (0 mm) Side ...................................................... 0” (0 mm) Back ...[...]

6 LDVR Series Direct Vent Gas Fireplace 10007317 Noncombustible materials such as brick or tile may be extended over the edges of the face of the fireplace. DO NOT cover any vent or grille panels. If a T rim Kit is going to be installed on the fireplace, the brick or tile will have to be installed flush with the edges of the fireplace. Final Fi[...]

7 LDVR Series Direct Vent Gas Fireplace 10007317 Installation 1. Thread the wiring through the holes on the end panels of the fireplace. T ake care not to cut the wire or insulation on metal edges. Route the wire to a conveniently located receptacle box. 2. Attach the wire to the ON/OFF switch and install the switch into the receptacle box. 3. Con[...]

8 LDVR Series Direct Vent Gas Fireplace 10007317 The fireplace, when installed, must be electrically connected and grounded in accordance with local codes or , in the ab- sence of local codes, with the current CSA C22.1 Canadian Electrical Code. For USA installations follow local codes and the national electrical code ANSI/ NFP A No. 70. It is str[...]

9 LDVR Series Direct Vent Gas Fireplace 10007317 Y our fireplace is approved to be vented either through the side wall, or vertically through the roof. • Only CFM Corporation venting components specifi- cally approved and labelled for this fireplace may be used. • V ent terminations shall not be recessed into a wall or siding. • Horizontal[...]

10 LDVR Series Direct Vent Gas Fireplace 10007317 V V V V V V V X X X D E B B B C B M B A J K F L VENT TERMINA TION AIR SUPPL Y INLET AREA WHERE TERMINAL IS NOT PERMITTED H I   Operable Operable Fixed Closed V B CFM145a DV T ermin Location 5/01/01 Rev . 12/05/01 sta INSIDE CORNER DET AIL V A G N N CFM145a General V [...]

1 1 LDVR Series Direct Vent Gas Fireplace 10007317 General Information Assembling V ent Pipes Canadian Installations: V enting system must be installed in accordance with the current CSA-B149.1 installation code. USA Installations: The venting system must conform with local codes and/ or the current National Fuel Gas code ANSI Z223.1/ NFP A 54. Onl[...]

12 LDVR Series Direct Vent Gas Fireplace 10007317 The vent chart should be read in conjunction with the following vent installation instructions to determine the relationship of the vertical and horizontal dimensions of the vent system. 1. Determine the height of the center of the horizontal vent pipe exiting through the outer wall. Using this dime[...]

13 LDVR Series Direct Vent Gas Fireplace 10007317 DVR584-600 Rear vent no elbows 2/99 djt 20" (508mm) T op View Straight V enting FP836 Rear V ent-T op View 1 1/21/98 20" (508mm) Max. REAR VENT -TOP VIEW 20" (508mm) Max. T op View Rear V ent Corner Installation Fig. 14 Rear vent applications, one 45° elbow . 45° 45° Rear W all Ins[...]

14 LDVR Series Direct Vent Gas Fireplace 10007317 CFM133 DVR Series T ypical corner install 2/26/01 sta Zero Clearance Sleev e Firestop CFM133 Fig. 17 Firestop and zero clearance sleeve in place. FP1005 Side View V ent T ermination 1/25/00 djt Finished W all V ent T ermi - nation FP1005 Fig. 18 Side view of final unit location. V ertical Sidewall [...]

15 LDVR Series Direct Vent Gas Fireplace 10007317 •IMPORT ANT• Minimum clearance between vent pipes and combustible materials is one (1”) inch (25 mm) on bottom, sides and top. T wist Lock V ent Starter Kit 7TDVSK, plus T ransition Elbow 7TDVRT90 must be used in V ertical Sidewall installations. The 4” pipe must be centered inside the 7” [...]

16 LDVR Series Direct Vent Gas Fireplace 10007317 V ertical Sidewall Installation STEP 1 Locate vent opening on the wall. It may be necessary to first position the fireplace and measure to obtain hole location. Depending on whether the wall is combustible or noncombustible, cut opening to size. (Fig. 25) For combustible walls first frame in open[...]

17 LDVR Series Direct Vent Gas Fireplace 10007317 STEP 6 Apply high temperature sealant to 4” (102 mm) and 7” (178 mm) collars or the termination one inch away from the end. Guide the vent termination’s 4” and 7” collars into their respective vent pipes. Double check that the vent pipes overlap the collars by 2” (51 mm). Secure the term[...]

18 LDVR Series Direct Vent Gas Fireplace 10007317 Do not back fill around snorkel. A clearance of at least 4” (102mm) must be maintained between the snorkel and the soil. BG401 Snorkel 2/10/99 djt Foundation Recess Snorkel W all Screws Recess Brackets W atertight Seal Around Pipe Sheet Metal Screws BG401 Fig. 32 Snorkel installation, recessed fo[...]

19 LDVR Series Direct Vent Gas Fireplace 10007317 V ertical Through-the-Roof Installation CFM100 Firestop-V ertical 09/20/00 1 1" 1 1" Joist Joist Firestop Spacer Nails (4) Upper Floor Attic Insulation Shield Ceiling Instal- lation CFM100 Fig. 35 Place firestop spacer(s) and secure. FP1021 T ypical vertical through the roof application 3[...]

20 LDVR Series Direct Vent Gas Fireplace 10007317 FP1022 T ypical Straight Up Installation 1/26/00 djt 40’ (12m) Storm Collar Roof Flash- ing V ent T ermination Roof 2’ Min. Roof Support Attic Insulation Shield Attic Insulation Joists Joists FP1022 Fig. 37 T ypical straight-up installation. Min. 2' (610 mm) FP1 185 Fig. 38 Minimum terminat[...]

21 LDVR Series Direct Vent Gas Fireplace 10007317 V enting Components 584G V enting Components Firestop spacer 2/25/99 djt 584H V enting components attic insulation shield 2/25/99 djt 584I vent components offset support 2/25/99 djt 584D V ent Components 90 degree elbow 2/25/99 djt 10/20/99 twist lock 584C V ent components 45 degree elbow 2/25/99 dj[...]

22 LDVR Series Direct Vent Gas Fireplace 10007317 Only glass approved by CFM Corporation should be used on this fireplace. The top louvre panel is removed by lifting the panel vertically and pulling it away from the appliance. (Fig. 39) The lower access door is hinged along the bottom edge and is folded down to allow access. 1. Turn the fireplace[...]

23 LDVR Series Direct Vent Gas Fireplace 10007317 1. Remove the top louvre assembly . 2. Open the bottom louvre. 3. Remove the window frame assembly . 4. Remove log box from inside firebox. 5. Unpack the logs from packaging and remove each log from its wrapping material. Set aside the ember and the lava rock bags. As with all plastic bags - these [...]

24 LDVR Series Direct Vent Gas Fireplace 10007317 36LDVR 1. Place rear log (B135) on rear bracket (ensure log is seated prop- erly to the bracket and located to the two pins), so it will not move from side to side and is firmly posi- tioned on the bracket. 2. Place front left log (B136). Use the log’s bottom hole to locate it onto the front supp[...]

25 LDVR Series Direct Vent Gas Fireplace 10007317 43LDVR 1. Place rear log (BD15) on rear bracket (ensure log is centered and seated properly to the log support). 2. Place front left log (BD16). Use log’s bottom notch to locate it onto the front support and just rest on top of the burner housing tile. 3. Place front right log (BD17). Use log’s [...]

26 LDVR Series Direct Vent Gas Fireplace 10007317     LG385 36LDV log flames 1/05 Glowing Embers LG385 LG384 33LDV log flames 1/05 Glowing Embers LG384     Glowing Embers LG415 Glowing Embers LG435 Fi[...]

27 LDVR Series Direct Vent Gas Fireplace 10007317 3. Open control access panel. 4. Push in gas control knob slightly and turn clock- wise to “OFF”. Do not force. 5. Close control access panel. 1. STOP! Read the safety information above. 2. Turn of f all electrical power to the fireplace. 3. For MN/MP/TN/TP appliances ONL Y , go on to Step 4. F[...]

28 LDVR Series Direct Vent Gas Fireplace 10007317 Lighting and Operating Instructions For Fireplaces equipped with SIT822 Gas V alve (EN or EP) A. This fireplace is equipped with an ignition device which automatically lights the pilot. DO NOT try to light the pilot by hand. B. BEFORE OPERA TING, smell all around the appliance area for gas. Be sure[...]

29 LDVR Series Direct Vent Gas Fireplace 10007317 T roubleshooting - Honeywell Millivolt V alve Remove Window Frame Assembly Before Service Work ST ART CHECK Gas Supply On ▼ ▼ ▼ ▼ ▼ Pilot Lights With Piezo Ignitor • Lockout Has Engaged. W ait 60 Seconds And T ry Again. • For Spark At Electrode While Depressing Piezo 1/8" Gap T o [...]

30 LDVR Series Direct Vent Gas Fireplace 10007317 T roubleshooting the Gas Control System SIT 822 V alve with Synetek Electronic Control Operating Diagram Normal Operation ON/OFF Switch Closed? Safe Start Check On? 0 Sec Purge Pilot Flame Sense OK? ON/OFF Switch Opened? Pilot and Main V alve OFF? 0 sec Post Purge? Ignition T rial: 30 sec Spark ON P[...]

31 LDVR Series Direct Vent Gas Fireplace 10007317 The conversion of this appliance from one gas to another must be carried out by an authorized service provider . 1. Disconnect power to the unit and shut off the gas sup - ply . 2. Remove window frame assembly . 3. Carefully remove the logs & lava rock material. 4. Remove the screws that are hol[...]

32 LDVR Series Direct Vent Gas Fireplace 10007317 Burner and Burner Compartment It is important to keep the burner and the burner compartment clean. At least once per year the logs and lava rock/ember material should be removed and the burner compartment vacuumed and wiped out. Remove and refit the logs as per the instructions in this manual. Alwa[...]

33 LDVR Series Direct Vent Gas Fireplace 10007317 CFM Corporation reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time, without notice. 33/36/39/43LDVR HI LO 22 21 19a,b 18a,b 41 17 30 33LDVR 1 1a 1b 1c 1d 1e 1f 1a 36LDVR 1 1g 1h 1i 2 3 6a,b 8 7a,b 9 1 1 12 13 14 15 16 20 2[...]

34 LDVR Series Direct Vent Gas Fireplace 10007317 LDVR (continued) Ref. Description 33LDVR 36LDVR 39LDVR 43LDVR 1. Log Set (complete) 10007567 10007318 10008214 10008314 1a. Log Front Left A43 B136 BC15 BD16 1b. Log Front Right -- B137 BC16 BD17 1c. Log Front Center -- B138 B138 B138 1d. Log Rear -- B135 BC14 BD15 1e. Log Rear Left A41 -- -- -- 1f.[...]

35 LDVR Series Direct Vent Gas Fireplace 10007317 LDVR (continued) Ref. Description 33LDVR 36LDVR 39LDVR 43LDVR 34. Support Front Log 10007562 100071 12 10008416 10008469 35. ON/OFF Switch 51842 51842 51842 51842 36. Ceramic Refractory Lining Kit (Optional) GADT3I0 GADT3J0 GADT3K0 GADT3N0 37. Relief Plate Assy (Burner Base) 10004192 10004192 100041[...]

36 LDVR Series Direct Vent Gas Fireplace 10007317 FK24 Fan Assembly This auxiliary fan system increases the efficiency of the circulation of the heated air . The FK24 fan kit allows variable speed control of the circulation fan and also incorporates a heat sensor in the circuit. Specifications 1 15 V olt / 60Hz / 56 Watts Maintenance The fan itse[...]

37 LDVR Series Direct Vent Gas Fireplace 10007317 Ceramic refractory panels are available in kit form for the LDV series appliances Appliance Model Kit Name 33LDVR 33LDVRCR 36LDVR 36LDVCR 39LDVR 39LDVCR 43LDVR 43LDVCR Ceramic Refractory Kits The fireplace, when installed, must be electrically connected and grounded in accordance with local codes o[...]

38 LDVR Series Direct Vent Gas Fireplace 10007317 Optional T rim Kits Louvre Accent T rim Appliance Model Main Louvre Kit Additional Louvre Polished Brass 33LDVR 33DVLMP 33DVLAP 36LDVR 36DVLMP 36DVLAP 39LDVR 39DVLMP 39DVLAP 43LDVR 43DVLMP 43DVLAP Antique Brass 33LDVR 33DVLMA 33DVLAA 36LDVR 36DVLMA 36DVLAA 39LDVR 39DVLMA 39DVLAA 43LDVR 43DVLMA 43DVL[...]

39 LDVR Series Direct Vent Gas Fireplace 10007317 BASIC W ARRANTY CFM Corporation (hereinafter referred to collectively as the Company) warrants that your new V ermont Castings or Majestic Gas Fireplace/ Stove is free from manufacturing and material defects for a period of one year from the date of purchase, subject to the following conditions and [...]

Efficiency Ratings Model EnerGuide Ratings Steady State (%) D.O.E. Fireplace Efficiency (%) Fan-OFF Fan-ON (AFUE%) 33LDVRRN 62.6 81 82 59 33LDVRRP 62.6 82 83 59 33LDVREN 72.7 81 82 59 33LDVREP 72.7 82 83 59 36LDVRRN 57.5 81 82 58 36LDVRRP 57.5 82 83 58 36LDVREN 63.6 81 82 58 36LDVREP 63.6 82 83 58 39LDVRRN 50.2 76 79 63 39LDVRRP 50.2 79 80 63 39L[...]