Vivotek VS3100P manuale d’uso

[...]

- 1 - www .vivotek.com Product name: Video Server (VS3100P) Rel ea s e D at e: 2005/04/07 Manual R evision: 1.30 We b s i t e : www.vivotek.com Email: technical@vivotek.com sales@vivotek.com Made in T aiwan. ©Copyright 2000-2005. All rights reserved[...]

- 2 - www .vivotek.com Before You Use This Product The use of surveillance devices may be prohibited by law in your country . The Video Server is not only a high-performance web-ready ca mera but also can be part of a flexible surveillance system. It is the u s er’ s resp onsibility to ensure that the operation of such devices is legal be fore in[...]

- 3 - www .vivotek.com Table of Contents Before Y ou Use This Prod uct ...................................................................... 2 P ackage Contents .................................................................................... 6 Physical Description ................................................................................[...]

- 4 - www .vivotek.com Fine-tuning for Best P erformance . ................................................. 19 Opening accounts for new users ... ................................................ 21 Change homepage layout ............................................................ 22 Build a multimedia web attraction site .........................[...]

- 5 - www .vivotek.com Query status of the digital input . .................................................. 55 Drive the digital output ............................................................... 55 R estore factory defaul t settings .................................................... 55 R estart system ......................................[...]

- 6 - www .vivotek.com Package Contents VS3100P P ower adapter I/O terminal block connector Software CD Quick installation gu ide W arranty card[...]

- 7 - www .vivotek.com Physical Description Front Panel BNC video input 75Ohms resistanc e video port for conne cting an external camera. T o ensure video modulation type being correctly detected, cameras should be attached and powered on before the Video Server is powered on.[...]

- 8 - www .vivotek.com BNC video output Bypass the video inpu t signal to additional terminal o r surveillance equipment. RCA audio input The audio input is connected by RCA connector of mono-audio Line- In signal. Status LED The Video Server provides a LED to show its status. Please refer to the appendix "T roubleshooting” for deta il. Rear[...]

- 9 - www .vivotek.com relay switch for device control. Pin 1 and pin 2 can be connect ed to an external sen sor device and the state of v ol tage will be monitored from the in itial state 'LOW'. The relay switch of pin 3 and pin 4 can be used to tu rn on or off the external de vice. Restore button There is a button hidden in the box for [...]

- 10 - www .vivotek.com Installation Hardware installation Before installing multiple Video Servers at the well-chosen locati ons, the Administrator should memorize the serial numbers on the packages respectively for future use. Cable connection Shut down all the peripheral devices prior to connection. Connect the supplied cables from the Video Ser[...]

- 11 - www .vivotek.com Software installation At the end of the hardware installation, users can u se Installation Wizard program included in the prod uct CDROM to find the location of the Video Server . There may b e many Video Servers in the local network. Users can differentiate the Video Servers with the serial number . The serial number is pri[...]

- 12 - www .vivotek.com Initial Access to the Video Server Check Network Settings The Video Server can be connected either before or immediately after software installation onto the Lo cal Area Network. The Administrator should complete the network settings on the configuration page, includi ng the correct subn et mask and IP address of gateway and[...]

- 13 - www .vivotek.com How to Use Authentication After opening the W eb browser and typin g in the URL of the Video Server , a dialogu e window pops up to request a u sername and password. Upon successful authentication, the following figure is displayed. The foreground is the login window and the background shows the me ssage if authentication fa[...]

- 14 - www .vivotek.com Installing plug-in F or the initial access to the Video Server in Windows, the web browser may prompt for permission to install a new plug-in for the Vi deo Server . P ermissio n request depends on the Internet security settings of the user ’ s PC or notebook. If the highest security level is set, the computer may prohibit[...]

- 15 - www .vivotek.com Primary user’s capability Main Screen with Camera View The main page layout has two parts: Configuration functions : The camera can be configured using these user interfaces. Camera View : What the camera sees. Click on the configuration link to the le ft of the image window to enter the configur a tion page.[...]

- 16 - www .vivotek.com Digital Zoom Click on the ma gnifier icon under the camera view then the digital zoom control panel will be shown. Uncheck “D isable digital zoo m” and use the slider contr ol to change the zoom factors. Digital Output Clicking on the “On” or “Off” bu tton turns the digital output to either on or off status. Snap[...]

- 17 - www .vivotek.com Client settings At the initial access to the “Connection type” page in Windows, the web browser will as k for a new plug-in in stallation, the plug-in being the Video Server . This plug-in ha s been registered for certification and can be used to change the parameters at the client ’ s site. The user may click on to in[...]

- 18 - www .vivotek.com The HTTP protocol must be selected if the network is prote cted by a firewall and it only allows HT TP Port (80) to be opened. In this mode, audio wi ll not be sent and only video is operational. If no special need is required, UDP protocol is recommended. Generally speaking, the client’s choice will be in the orde r of UD[...]

- 19 - www .vivotek.com Administrator’s capability Fine-tuning for Best Performance Best performance generally equates to the fa stest image refresh rate with the best video quality , and at the lo west network bandwidth as possible. The three factors, “Maximum frame r ate” , “Fix bit rate” , and “F ix quality” on the Video Configu r [...]

- 20 - www .vivotek.com the bit r ate according to your bandwidth and set the maximum frame rate to 25 fps or 30 fps. If the images vary dramatically in your environment, you may want to slow the maximum frame r ate down to 20 fps in order t o lower the rate of data transmission. This allows for better video qu ality and the human eyes cannot readi[...]

- 21 - www .vivotek.com Opening accounts for new users Protect Video Server by passwords The Video Server is shipped without any password by default. That m e an s every one can access t he Video Server in cluding the configur ation as long as the IP addres s is known. It is necessary to assign a password if the Video Server is intended to be acces[...]

- 22 - www .vivotek.com More flexible options for viewers ○ 4 The first option allow s any one u ses “demo” as the user name to view w ithout password. The Administrator can also decide if more viewers ar e allowed to watch the video if the viewers exceed the limit. The overloaded vi ewers will have snapshot mod e instead. Change homepage lay[...]

- 23 - www .vivotek.com How to change the font color 1. Click on “Configuration” on homepage, 2. Click on “Homepage layout” at the left column, 3. Find “Font color” a nd pull down the list to choo se any color you like, 4. Click on “Save” button. * The font colo r is better to contrast with the backgr ound. How to change the backgro[...]

- 24 - www .vivotek.com If you want to use the image from ano ther web site as background, 3. Find “Background gr aph” and cho ose “Url” , 4. T ype the URL of the image on the Internet in th e edit box, for example, “http://dgl.microsoft.com/thum bnails/j023/j0235217(t).gif” , 5. Click on “Save” button. If you want to change the def[...]

- 25 - www .vivotek.com How to change the image logo at the upper left corner of homepage 1. Click on “Configuration” on homepage, 2. Click on “Homepage layout” at the left column, If y ou want t o r emove a ny logo , 3. Find “Logo graph” and choose “blank” , 4. Click on “Save” button. If you want to use the image from ano ther [...]

- 26 - www .vivotek.com 7. T ransfer logo.gif in local folder to the Vi deo Server , 8. Close the F TP program and reload the homepage of the Video Server . If you want to add hyperlink to the logo image, 3. Find “Logo l ink” and type the hyp erlink in the edit bo x, for example, http://www.m ywebsite.com, 4. Click on “Save” button.[...]

- 27 - www .vivotek.com How to design my own homepage to replace the current one 1. Prepare your own homepag e with size less than 65000 bytes and rename it to user .htm, 2. Insert the html codes of video obje ct, the bold Italian text in the following example, into the appropriate position in user .htm. Note that the cod es of video object must be[...]

- 28 - www .vivotek.com 3. Open an FT P client progr a m and connect to the Video Server . The use r name and password is a s same as the Administrator ’ s. 4. T r ansfer user .htm in local folder to the Video Server , 5. Close the F TP program and reload the homepage of the Video Server , 6. Click on “Configuration” on homepage, 7. Click on [...]

- 29 - www .vivotek.com Build a multimedia web attraction site Demo on multiple sites – mid-scale service The Video Server can allow ten visitors on- line simultaneously . After Installation, fo cus the Video Server on any view y ou would like fr iends to share an d tell the visitors to type in the web browse r address. Caution: Y ou may want to [...]

- 30 - www .vivotek.com If you want to expand to allow in more viewers, the host server should be able to handle large network traffic, which must ha ndle the picture refres hing fr om t he Vid eo Server . If the web space ha s FTP servic e, Set the Video Server as an FTP client to up load the pictures. T he access to the Video Server will be indep[...]

- 31 - www .vivotek.com 5. Click on “ Applicati on” at the left column, 6. Select the weekday and daily schedule yo u w ant to upload the pictures, 7. Select “Sequential operation” and set the interval, 8. Select F TP without date time suff ix as the upload method an d click on save, 9. The image file uploaded to the web space is n amed “[...]

- 32 - www .vivotek.com ****** Example homepage begin ****** <html> <head> <title>Example - au to refresh</title> </head> <body background="/pic/wallppr .jpg"> <p align=left> <font size="7" face ="Comic Sans MS" color="#FF0000"> Video Server Demo < / f o n t [...]

- 33 - www .vivotek.com Build a security application The Administrator can combine options on th e application page to perform many useful security applications. There a re two trigger sources coming from attached devices such as for motion detection. There are also two kinds of actions responding to such events, including uploading snapshots over [...]

- 34 - www .vivotek.com 5. Set the delay before detecting ne xt event to avoid continuous false alarms following the original ev ent, 6. Set the delay to take snapshots after event to capture the direction of the moving objects, Send snapshots when motion is detected If no ext ernal sensor is a vailabl e, Administ rator can use the built -in motion[...]

- 35 - www .vivotek.com 16. Check “Upload snapshots while m otion detected” , if e-mailing the snapshots is preferred, 17. Check “Send snapshots by email” , 18. Click on save to validate.[...]

- 36 - www .vivotek.com Software revision upgrade Customers can obtain the up-to-date so ftw are from the web site of Vivotek. An easy -to -use Installation Wizard is provided to upgrade the Video Server with just a few clicks. The upgrade function is opened to the Administr ator only . T o upgrade the system, follow the procedures below. 1. Downlo[...]

- 37 - www .vivotek.com Definitions in Configuration Only the Administrator can access sy stem configuration. Each category in the left column will be explained in the following pages. The bold texts are the specific phr a ses on the Option pages. The Administrator may t ype the URL below the figure to directly enter the frame page of configuration[...]

- 38 - www .vivotek.com System parameters "Host name" The text displays the title at the top of the ma in page. “Turn off the LED indicator” Check this option to shut off the LED be side the lens. It can prev ent others from obs e rving the oper ation. "Keep current date and time" Click on this to reserve the current date an[...]

- 39 - www .vivotek.com Security settings “Root password” Change the Administrator’s password by typing in the new passwo rd identically in both t ext boxes. The typed entries will be display ed as asterisks for security purposes. After pressing , the web browser wi ll ask the Administr ator for the new passwor d for access. “Add user” T [...]

- 40 - www .vivotek.com Network settings Any changes made on this page will restart the system in order to validate the changes. Make sure every field is entered correctly before clicking on . "Reset IP address at next boot" , the default status is che ck ed to get IP add ress automatically at the server start. Therefor e, once the networ[...]

- 41 - www .vivotek.com “User name of SMTP 2” , gr a nted user name on the backup email server . “Password of SMTP 2” , granted password on the backup e mail server . “Recipient email address 2” The email address of the recipients for the ba ckup server . “Sender email address” , the email address of the sender . FTP “Local FTP se[...]

- 42 - www .vivotek.com users must be not ified the change for the connection to be su ccessful. For instance, when the Administrator changes the HT TP port of th e Video Server whose IP address is 192.168.0.100 from 80 to 8080, th e users must type in the web browser “http://192.168.0.10 0:8080” instead of “http:// 192.168.0.100” . Streami[...]

- 43 - www .vivotek.com DDNS and UPnP settings “Enable DDNS” This option turns on the DDNS function. “Provider” The p rovider list contains four hosts that provide DDNS services. Please connect to the service provider ’ s website to make sure the service charges. “Host name” If users wants to use DDNS service, th is field must be fill[...]

- 44 - www .vivotek.com Video codec parameters “Text on video” The text will be displayed in the black bar a bove the video window with a timestamp. The timesta mp is captur ed from the date and time of the Video Server that is maintained by a built-in real-time clock. “Color” Select either fo r color or monochrome vid eo display . “Size?[...]

- 45 - www .vivotek.com[...]

- 46 - www .vivotek.com Motion detection “Enable motion detection” Check this option to turn on motion detect ion. Click on this button to add a new window . At most three windows can exist simult ane ously . Use the mouse to cl ick, hold, and drag t he window frame to resize or the title bar to move. Clicking on the ‘x’ at the upper right-[...]

- 47 - www .vivotek.com Application settings Weekly schedule “Sun” ~ “Sat” Select the days of the wee k to perform the follo wing oper a tions. “Snapshots begin at” Set the time to start operations. “Snapshots stop at” Set the time to stop operations. Setting identical begin time and stop time means 24-hour operation. “All the tim[...]

- 48 - www .vivotek.com for the snapshots, before event, right upon event, and after event. The date and time suffix may also be added a s an option. Confirm the e xternal mail or F TP server settings in the network configuration. “ Reset output ” Select and sa v e t his op t ion to r ese t t he ex t ernal de vi c e at t he di gi t al output to[...]

- 49 - www .vivotek.com Homepage layout settings “Use the customized homepage” , check this option to use “user .htm” uploade d by the Administrator instead of the default one. R efer to the section “ Administrator’s capability” for detail us age. The following op tions related to the default homepage will not affect the “user .htm?[...]

- 50 - www .vivotek.com Viewing system log Click the link on th e configur ation pag e to view the syst em log file . The content of the file provides usefu l information about configuration and connection after system boot- up. Viewing system parameters Click on this link on th e configuration page to view the entire system’ s par ameter set. Th[...]

- 51 - www .vivotek.com Appendix A. Troubleshooting Status LED After powering up, the Video Server performs a self -d iagnostic to detect any hardware defect s. The following t able lists the LED patt erns in genera l. In case of any fatal e rror , the LED will blink in a patte rn other than those below. Condition LED color During self-diagnostic a[...]

- 52 - www .vivotek.com B. Frequently asked questions Q What if I for get my password? A After the Ad ministr ator' s password is a ssigned, every access to the Video Server needs authentication. If y ou a re one of the managed users, you have to ask the Administrator for the password. If you are the Administrator , there is no wa y to recov e[...]

- 53 - www .vivotek.com Q Can I install it on ceiling? A Y es. There are flip and mirror options in video configuration page to correct the images for upside down installation. Q The image is not clear enough. A Rotate the lens to adjust the focus a fter the Video Server is installed in the pro per position. The image setting s and white ba lance c[...]

- 54 - www .vivotek.com Q How fast is the video rate of the Video Server? A The MPEG4 codec engine can process 30 fr ames per second in ternally . H owever the total performance is subje ct to many coefficients as follows: 1. Network throughput, 2. Bandwidth share, 3. Number of users, 4. The complicated/detailed ob jects and movement in view , 5. T[...]

- 55 - www .vivotek.com C. URL commands of the Video Server For some customers who already have their own web site or web control a pplication, the Video Server can be easily integrated through convenient URLs. This section lists the commands in URL forma t corresponding to the basic functions o f the erase Video Server . Capture update Snapshot of[...]

- 56 - www .vivotek.com The Video Server will automati cally restart after restoring factory default configurations. Restart system /setup/reset.cgi R estart the Video Server without warning.[...]

- 57 - www .vivotek.com Page URL The configuration page has a frame layout including an option list frame and an option page frame. R eferen ced URLs, except for th e configuration page, direct users to the option page frame only . Some pages, such as image quality setting and preset setting, are opened in new windows for preview . Only the Adminis[...]

- 58 - www .vivotek.com General format of command URL Every configur ation can be set through URL with POST method by the Administrator only . <general format> URL[?[name=value][&name=v alue]……] <method> POST <authorized user> root System configuration URL URL: /setup/system.cgi NAME V ALUE DESCRIPTION host <text string[...]

- 59 - www .vivotek.com Security configuration URL URL: /setup/security .cgi NAME V ALUE DESCRIPTION rootpass <text string shorter than 15 characters> change root passw ord username <text string shorter than 15 characters> add new user userpass <text string shorter than 15 characters> new user's password deluser <text stri[...]

- 60 - www .vivotek.com smtp1 <domain name or IP address> primar y SMTP server smtp1Usr <string shorter than 39 characters> user name for pr imary SMTP server smtp1pass <string shorter than 39 characters> password for primary SMTP server mail1 <string shorte r than 80 characters> mail recipient address smtp2 <domain name [...]

- 61 - www .vivotek.com yes access FTP server in passive mode Pasv2 no access F TP server in active mode http <number less than 65535> HT TP port cport <number less than 6 5535> control Channel port aport <number less than 65535> audio Channel port vport <number less than 65535> video Channel port yes optimal for the low ban[...]

- 62 - www .vivotek.com enupnp yes, no Enable UPnP function. This option must be resent whenever the U RL is called, if UPnP function is to be enabled. enupnpnat yes, no Enable UPnP port forwarding. Video configuration URL URL: /setup/video.cgi NAME V ALUE DESCRIPTION text <text string shorter than 1 5 characters> enclosed caption B/W monochr[...]

- 63 - www .vivotek.com 256000 set bit rate to 256K b ps 384000 set bit rate to 384K b ps 512000 set bit rate to 512K b ps 768000 set bit rate to 768K b ps 1000000 set bit r ate to 100 0K bps 1200000 set bit r ate to 120 0K bps 1 set maximum frame rate to 1 fps 2 set maximum frame rate to 2 fps 3 set maximum frame rate to 3 fps 5 set maximum frame [...]

- 64 - www .vivotek.com[...]

- 65 - www .vivotek.com Application configuration URL URL: /setup/app.cgi NAME V ALUE DESCRIPTION emode <not required> event mode applica tion smode <not required> sequential mode application mail upload snapshots by email smethod ftp upload snapshots by FTP suffix <not required> FTP file with date and time suff ix delay <integ[...]

- 66 - www .vivotek.com Homepage layout configuration URL URL: /setup/layout.cgi NAME V ALUE DESCRIPTION blank hide logo def use default logo cuslogo url use image from URL logourl <text string shorter than 80 characters> URL of image for logo linkurl <text string sh orter than 80 characters> URL to link when clicking on l o go blank hi[...]

- 67 - www .vivotek.com D. Technical specifications - System CPU: T rimedi a PNX130 0 RAM: 8MB SDRAM ROM: 2MB FLASH ROM - Networking Protocol TCP /IP , HT TP , SMTP , FTP , T elnet, NT P , DNS , DHCP , DRM, DDNS and UPnP Physical 10Base T Ethernet or 100Base T F ast Ethernet - Video Algorithm supported MPEG4(short header mode) Video Input 1 BNC com[...]

Electromagnetic Compatibility (EMC) This device compiles wit h FCC Rules Part 15. Ope r ation is subject to the follo w ing two conditions. • This device may not cause harmful interfere nce, and • This device must accept any interferen ce received, including interf erence that may cause undesired operation. USA - This equipment has been tested [...]