Yamaha F60D manuale d’uso

Printed in Japan May 2004–1.5 × 1 ! Printed on recycled paper F50D T50D F60D T60D O WNER’S MANU AL 6C1-28199-10 U .S.A.Edition LIT -18626-06-11 6C1-9-10 Hyoshi 4/28/04 3:48 PM Page 1[...]

EMU25060 ZMU01690 Read this owner ’ s manual carefully before operating your outboard motor. 6C1-9-10 Hyoshi 4/28/04 3:48 PM Page 2[...]

Important manual information EMU25100 To the owner Thank you for choosing a Yamaha outboard motor. This Owner’s Manual contains infor- mation needed for proper operation, mainte- nance and care. A thorough understanding of these simple instructions will help you ob- tain maximum enjoyment from your new Yamaha. If you have any question about the o[...]

Table of contents General information .......................... 1 Identification numbers record .......... 1 Outboard motor serial number .......... 1 Key number ....................................... 1 Emission control information ........... 1 North American models..................... 1 Star labels ......................................... 2 S[...]

Table of contents and power trim and tilt models) ..... 31 Stopping engine ............................ 32 Procedure ....................................... 32 Trimming outboard motor .............. 32 Adjusting trim angle ........................ 33 Adjusting boat trim .......................... 34 Tilting up and down ....................... 34 Pr[...]

1 General information EMU25170 Identification numbers record EMU25182 Outboard motor serial number The outboard motor serial number is stamped on the label attached to the port side of the clamp bracket or the upper part of the swivel bracket. Record your outboard motor serial number in the spaces provided to assist you in ordering spare parts from[...]

General information 2 EMU25262 Manufactured date label This label is attached to the clamp bracket or the swivel bracket. EMU25272 Star labels Your outboard motor is labeled with a Cali- fornia Air Resources Board (CARB) star la- bel. See below for a description of your particular label. EMU25280 One Star—Low Emission The one-star label identifie[...]

General information 3 EMU25300 Three Stars—Ultra Low Emission The three-star label identifies engines that meet the Air Resources Board’s 2008 ex- haust emission standards. Engines meeting these standards have 65% lower emissions than One Star-Low-Emission engines. EMU25361 Safety information ● Before mounting or operating the outboard motor,[...]

General information 4 of the road” on page 5. ● Stay informed about the weather. Check weather forecasts before boating. Avoid boating in hazardous weather. ● Tell someone where you are going: leave a Float Plan with a responsible person. Be sure to cancel the Float Plan when you re- turn. ● Use common sense and good judgment when boating. [...]

General information 5 shown. Otherwise, engine damage could result from Leaking oil. EMU25500 Basic boating rules (Rules of the road) Just as there are rules which apply when you are driving on streets and high ways, there are waterway rules which apply when you are driving your boat. These rules are used internationally, and are also enforced by t[...]

General information 6 ed area must yield to you (they are the Give- Way vessels). Both you and the meeting vessel must alter course to avoid each other. Meeting If you are meeting another power vessel head on, and are close enough to run the risk of collision, neither of you has the right-of- way! Both of you should alter course to avoid an acciden[...]

General information 7 from local marine supply stores. Fishing vessel right-of-way All vessels which are fishing with nets, lines or trawls are considered to be “fishing ves- sels” under the International Rules. Vessels with trolling lines are not considered fishing vessels. Fishing vessels have the right-of- way regardless of position. Fishing[...]

General information 8 EMU25540 Fueling instructions W ARNING EWM00010 GASOLINE AND ITS VAPORS ARE HIGH- LY FLAMMABLE AND EXPLOSIVE! ● Do not smoke when refueling, and keep away from sparks, flames, or other sources of ignition. ● Stop engine before refueling. ● Refuel in a well-ventilated area. Refuel portable fuel tanks off the boat. ● Tak[...]

General information 9 dry rags. ● Do not overfill the fuel tank. ● Tighten the filler cap securely after re- fueling. ● If you should swallow some gasoline, inhale a lot of gasoline vapor, or get gasoline in your eyes, get immediate medical attention. ● If any gasoline spills onto your skin, im- mediately wash with soap and water. Change cl[...]

General information 10 electric system could perform poorly or be overloaded, causing electric system damage. For electric start models, choose a battery which meets the following specifications. EMU25711 Battery specifications NO TE: The engine cannot be started if battery volt- age is too low. EMU25742 Propeller selection The performance of your [...]

General information 11 the engine in the proper operating range. For instructions on propeller removal and in- stallation, see page 53. EMU25770 Start-in-gear protection Yamaha outboard motors or Yamaha-ap- proved remote control units are equipped with start-in-gear protection device(s). This feature permits the engine to be started only when it is[...]

12 Basic components EMU25795 Main components NO TE: * May not be exactly as shown; also may not be included as standard equipment on all mod- els. F50D, T50D, F60D, T60D EMU25802 Fuel tank If your model was equipped with a portable fuel tank, its function is as follows. W ARNING EWM00020 The fuel tank supplied with this engine is its dedicated fuel[...]

Basic components 13 mercial users should conform to relevant licensing or approval authority regula- tions. EMU25830 Fuel joint This joint is used to connect the fuel line. EMU25841 Fuel gauge This gauge is located on either the fuel tank cap or on the fuel joint base. It shows the ap- proximate amount of fuel remaining in the tank. EMU25850 Fuel t[...]

Basic components 14 EMU26201 Neutral interlock trigger To shift out of neutral, first pull the neutral in- terlock trigger up. EMU26211 Neutral throttle lever To open the throttle without shifting into ei- ther forward or reverse, put the remote con- trol lever in the neutral position and lift the neutral throttle lever. NO TE: The neutral throttle[...]

Basic components 15 EMU25990 Engine stop lanyard switch The lock plate must be attached to the en- gine stop switch for the engine to run. The lanyard should be attached to a secure place on the operator’s clothing, or arm or leg. Should the operator fall overboard or leave the helm, the lanyard will pull out the lock plate, stopping ignition to [...]

Basic components 16 EMU26141 Power trim and tilt switch on remote control or tiller handle The power trim and tilt system adjusts the outboard motor angle in relation to the tran- som. Pressing the switch “ ” (up) trims the outboard motor up, then tilts it up. Pressing the switch “ ” (down) tilts the outboard mo- tor down and trims it down.[...]

Basic components 17 protect the engine from electrochemical corrosion. Never paint the trim tab as it will become ineffective as an anode. EMU26340 Tilt support lever for power trim and tilt or hydro tilt model To keep the outboard motor in the tilted up position, lock the tilt support lever to the clamp bracket. EMU26372 Top cowling lock lever(s) [...]

Basic components 18 EMU26491 Digital tachometer The tachometer shows the engine speed and has the following functions. NO TE: All segments of the display will light momen- tarily after the main switch is turned on and will return to normal thereafter. NO TE: The water separator and engine trouble warning indicators only operate when the en- gine is[...]

Basic components 19 does not indicate the engine oil level. Use the oil dipstick to check the re- maining oil quantity. For further infor- mation, see page 27. EMU26571 Overheat warning indicator If the engine temperature rises too high, this indicator will flash. For further information on reading the indicator, see page 23. CAUTION: ECM00050 Do n[...]

Basic components 20 After a few seconds, the gauge will change to normal operation. Watch the gauge when turning on the main switch to make sure all segments come on. NO TE: The speedometer displays km/h, mph, or knots, according to operator preference. Se- lect the desired unit of measurement by set- ting the selector switch on the back of the gau[...]

Basic components 21 ● Changing the display format ● Pressing the “ ” (mode) button chang- es the display format in the following pat- tern: ● Total hours → Trip hours → Display off ● Resetting the trip hours ● Simultaneously pressing the “ ” (set) and “ ” (mode) buttons for more than 1 second while the trip hours are displ[...]

Basic components 22 NO TE: The clock operates on battery power. Dis- connecting the battery will stop the clock. Reset the clock after connecting the battery. EMU26710 Fuel gauge The fuel level is indicated by eight segments. When all segments are showing, the fuel tank is full. CAUTION: ECM00860 The Yamaha fuel tank sensor differs from conventiona[...]

Basic components 23 EMU26801 Warning system CAUTION: ECM00090 Do not continue to operate the engine if a warning device has activated. Consult your Yamaha dealer if the problem can- not be located and corrected. EMU26813 Overheat warning This engine has an overheat warning device. If the engine temperature rises too high, the warning device will ac[...]

Basic components 24 ● The low oil pressure warning indicator will light. ● The buzzer will sound (if equipped on the tiller handle, remote control box, or main switch panel). If the warning system has activated, stop the engine as soon as it is safe to do so. Check the oil level and add oil as needed. If the oil level is correct and the warning[...]

25 Operation EMU26901 Installation CAUTION: ECM00110 Incorrect engine height or obstructions to smooth water flow (such as the design or condition of the boat, or accessories such as transom ladders or depth finder transducers) can create airborne water spray while the boat is cruising. Severe engine damage may result if the motor is operated conti[...]

Operation 26 motor greatly affects the water resistance. If the mounting height is too high, cavitation tends to occur, thus reducing the propulsion; and if the propeller tips cut the air, the engine speed will rise abnormally and cause the en- gine to overheat. If the mounting height is too low, the water resistance will increase and thereby reduc[...]

Operation 27 ● Check fuel line connections to be sure they are tight (if equipped Yamaha fuel tank or boat tank). ● Be sure the fuel tank is positioned on a se- cure, flat surface, and that the fuel line is not twisted or flattened, or likely to contact sharp objects (if equipped Yamaha fuel tank or boat tank). EMU27130 Controls ● Check throt[...]

Operation 28 tank. Wipe up any spilled fuel. EMU27270 Ring Free Fuel Additive Gasoline is a precise blend of many different substances, each chosen to give certain characteristics. Gasoline blends have been changing in recent years in response to con- cerns about pollution and resulting emis- sions regulations. One of the most obvious changes has b[...]

Operation 29 connect the fuel line to the joint. Then firmly connect the other end of the fuel line to the joint on the fuel tank. 3. If a steering friction adjuster is provided on your outboard motor, securely attach the fuel line to the fuel line clamp. NO TE: During engine operation place the tank hori- zontally, otherwise fuel cannot be drawn f[...]

Operation 30 lanyard where it could become entan- gled, preventing it from functioning. ● Avoid accidentally pulling the lanyard during normal operation. Loss of en- gine power means the loss of most steering control. Also, without engine power, the boat could slow rapidly. This could cause people and objects in the boat to be thrown forward. 3. [...]

Operation 31 not be found. ● A continuous flow of water from the pi- lot hole shows that the water pump is pumping water through the cooling passages. If water is not flowing out of the pilot hole at all times while the en- gine is running, overheating and seri- ous damage could occur. Stop the engine and check whether the cooling water inlet on [...]

Operation 32 EMU27820 Stopping engine Before stopping the engine, first let it cool off for a few minutes at idle or low speed. Stop- ping the engine immediately after operating at high speed is not recommended. EMU27844 Procedure 1. Push and hold the engine stop button or turn the main switch to “” (off). 2. After stopping the engine, disconne[...]

Operation 33 the boat, sea conditions, and running speed. W ARNING EWM00740 Excessive trim for the operating condi- tions (either trim up or trim down) can cause boat instability and can make steering the boat more difficult. This in- creases the possibility of an accident. If the boat begins to feel unstable or is hard to steer, slow down and/or r[...]

Operation 34 angles to find the position that works best for your boat and operating conditions. NO TE: To adjust the trim angle while the boat is moving, use the power trim and tilt switch lo- cated on the remote control device or tiller handle, if equipped. EMU27911 Adjusting boat trim When the boat is on plane, a bow-up attitude results in less [...]

Operation 35 salt corrosion. W ARNING EWM00220 Be sure all people are clear of the out- board motor when tilting up and down, also be careful not to pinch any body parts between the drive unit and engine bracket. W ARNING EWM00250 Leaking fuel is a fire hazard. If there is a fuel joint on the outboard motor, discon- nect the fuel line or close the [...]

Operation 36 W ARNING EWM00260 After tilting the outboard motor, be sure to support it with the tilt support knob or tilt support lever. Otherwise the outboard motor could fall back down suddenly if oil in the power trim and tilt unit loses pres- sure. 5. Models equipped with trim rods: Once the outboard motor is supported with the tilt support lev[...]

Operation 37 to allow operation in shallow water. W ARNING EWM00660 ● Place the gear shift in neutral before setting up for shallow water cruising. ● Return the outboard motor to its normal position as soon as the boat is back in deeper water. CAUTION: ECM00260 Do not tilt the outboard motor up so that the cooling water inlet on the lower unit [...]

38 Maintenance EMU28216 Specifications Dimension: Overall length: 706 mm (27.8 in) Overall width: 384 mm (15.1 in) Overall height L: F50TR 1415 mm (55.7 in) F60TR 1415 mm (55.7 in) T50TR 1455 mm (57.3 in) T60TR 1455 mm (57.3 in) Overall height X: 1569 mm (61.8 in) Transom height L: F50TR 527 mm (20.7 in) F60TR 527 mm (20.7 in) T50TR 530 mm (20.9 in[...]

Maintenance 39 F50TR G F60TR G T50TR K T60TR K Fuel and oil: Recommended fuel: Regular unleaded gasoline Min. pump octane: 86 Recommended engine oil: 4-stroke outboard motor oil Engine oil grade API: API SE, SF, SG, SH, SJ Engine oil type SAE: SAE10W30 or SAE10W40 Lubrication: Wet sump Engine oil quantity (excluding oil filter): 2.5 L (2.64 US qt) [...]

Maintenance 40 EMU28280 Storing outboard motor When storing your Yamaha outboard motor for prolonged periods of time (2 months or longer), several important procedures must be performed to prevent excessive damage. It is advisable to have your outboard motor serviced by an authorized Yamaha dealer prior to storage. However, you, the owner, with a m[...]

Maintenance 41 5. Cooling system flushing is essential to prevent the cooling system from clog- ging up with salt, sand, or dirt. In addi- tion, fogging/lubricating of the engine is mandatory to prevent excessive engine damage due to rust. Perform the flush- ing and fogging at the same time. W ARNING EWM00090 ● Do not touch or remove electrical p[...]

Maintenance 42 EMU28430 Battery care W ARNING EWM00330 Battery electrolytic fluid is dangerous; it contains sulfuric acid and therefore is poisonous and highly caustic. Always follow these preventive mea- sures: ● Avoid bodily contact with electrolytic fluid as it can cause severe burns or permanent eye injury. ● Wear protective eye gear when h[...]

Maintenance 43 2. Screw the garden hose connector onto a garden hose which is connected to a fresh water supply. 3. With the engine off, turn on the water tap and let the water flush through the cool- ing passages for about 15 minutes. Turn off the water and disconnect the garden hose. 4. When flushing is complete, reinstall the garden hose connect[...]

Maintenance 44 have the mechanical skills, tools, and other equipment necessary to perform mainte- nance not covered by this owner ’ s manual. EMU28510 Replacement parts If replacement parts are necessary, use only genuine Yamaha parts or parts of the same type and of equivalent strength and materi- als. Any part of inferior quality may malfunc- [...]

Maintenance 45 EMU28521 Maintenance chart Frequency of maintenance operations may be adjusted according to the operating condi- tions, but the following table gives general guidelines. Refer to the sections in this chapter for explanations of each owner-specific action. The “” symbol indicates the check-ups which you may carry out yourself. The[...]

Maintenance 46 NO TE: When operating in salt water, turbid or muddy water, the engine should be flushed with clean water after each use. EMU28871 Maintenance chart (additional) Spark plug(s) Cleaning / adjustment / replacement Timing belt Inspection / replace- ment V alve clearance (OHC , OHV) Inspection / adjustment Item Actions Initial Every 10 h[...]

Maintenance 47 EMU28931 Greasing Yamaha marine grease (Water resistant grease) F50D, T50D, F60D, T60D EMU28951 Cleaning and adjusting spark plug W ARNING EWM00560 When removing or installing a spark plug, be careful not to damage the insulator. A damaged insulator could allow external sparks, which could lead to explosion or fire. The spark plug is[...]

Maintenance 48 adjust the gap to specification if necessary. When fitting the plug, always clean the gas- ket surface and use a new gasket. Wipe off any dirt from the threads and screw in the spark plug to the correct torque. NO TE: If a torque-wrench is not available when you are fitting a spark plug, a good estimate of the correct torque is 1/4 t[...]

Maintenance 49 EMU28980 Inspecting fuel filter W ARNING EWM00310 Gasoline is highly flammable, and its va- pors are flammable and explosive. ● If you have any question about properly doing this procedure, consult your Yamaha dealer. ● Do not perform this procedure on a hot or running engine. Allow the engine to cool. ● There will be fuel in t[...]

Maintenance 50 the filter housing. 5. Attach the filter assembly to the bracket. 6. Run the engine and check the filter and lines for leaks. EMU29040 Inspecting idling speed W ARNING EWM00450 ● Do not touch or remove electrical parts when starting or during operation. ● Keep hands, hair, and clothes away from the flywheel and other rotating par[...]

Maintenance 51 sition (not tilted). 2. Prepare a suitable container that holds a larger amount than the engine oil capac- ity. Loosen and remove the drain screw while holding the container under the drain hole. Then remove the oil filler cap. Let the oil drain completely. Wipe up any spilled oil immediately. 3. Put a new gasket on the oil drain scr[...]

Maintenance 52 below the lower mark, or drain to the specified level if it is above the upper mark. 7. Dispose of used oil according to local regulations. NO TE: ● For more information on the disposal of used oil, consult your Yamaha dealer. ● Change the oil more often when operating the engine under adverse conditions such as extended trolling[...]

Maintenance 53 5. Tilt the outboard motor down. Check that the trim and tilt rod operates smoothly. NO TE: Consult your Yamaha dealer if any operation is abnormal. EMU29171 Checking propeller W ARNING EWM00321 You could be seriously injured if the en- gine accidentally starts when you are near the propeller. ● Before inspecting, removing, or inst[...]

Maintenance 54 EMU30660 Removing the propeller EMU29194 Spline models 1. Straighten the cotter pin and pull it out using a pair of pliers. 2. Remove the propeller nut, washer, and spacer (if equipped). 3. Remove the propeller and thrust wash- er. EMU30670 Installing the Propeller EMU29231 Spline models CAUTION: ECM00340 ● Be sure to install the t[...]

Maintenance 55 specified torque, tighten the nut further to align it with the hole. EMU29281 Changing gear oil W ARNING EWM00800 ● Be sure the outboard motor is securely fastened to the transom or a stable stand. You could be severely injured if the outboard motor falls on you. ● Never get under the lower unit while it is tilted, even when the [...]

Maintenance 56 level plug. 7. Insert and tighten the gear oil drain screw. EMU29302 Cleaning fuel tank W ARNING EWM00920 Gasoline is highly flammable, and its va- pors are flammable and explosive. ● If you have any question about properly doing this procedure, consult your Yamaha dealer. ● Keep away from sparks, cigarettes, flames, or other sou[...]

Maintenance 57 EMU29320 Checking battery (for electric start models) W ARNING EWM00330 Battery electrolytic fluid is dangerous; it contains sulfuric acid and therefore is poisonous and highly caustic. Always follow these preventive mea- sures: ● Avoid bodily contact with electrolytic fluid as it can cause severe burns or permanent eye injury. ●[...]

Maintenance 58 2. Always keep the battery in a good state of charge. Installing a voltmeter will help you monitor your battery. If you will not use the boat for a month or more, re- move the battery from the boat and store it in a cool, dark place. Completely re- charge the battery before using it. 3. If the battery will be stored for longer than a[...]

Maintenance 59 EMU29400 Coating the boat bottom A clean hull improves boat performance. The boat bottom should be kept as clean of ma- rine growth as possible. If necessary, the boat bottom can be coated with an anti-foul- ing paint approved for your area to inhibit marine growth. Do not use anti-fouling paint which includes copper or graphite. The[...]

60 Trouble Recovery EMU29422 Troubleshooting A problem in the fuel, compression, or igni- tion systems can cause poor starting, loss of power, or other problems. This section de- scribes basic checks and possible remedies, and covers all Yamaha outboard motors. Therefore some items may not apply to your model. If your outboard motor requires repair[...]

Trouble Recovery 61 Q. Is fuel system obstructed? A. Check for pinched or kinked fuel line or other obstructions in fuel system. Q. Is fuel contaminated or stale? A. Fill tank with clean, fresh fuel. Q. Is fuel filter clogged? A. Clean or replace filter. Q. Have ignition parts failed? A. Have serviced by a Yamaha dealer. Q. Has warning system activ[...]

Trouble Recovery 62 A. Have serviced by a Yamaha dealer. Q. Is load on boat improperly distributed? A. Distribute load to place boat on an even plane. Q. Is water pump or thermostat faulty? A. Have serviced by a Yamaha dealer. Q. Is there excess water in fuel filter cup? A. Drain filter cup. Engine power loss. Q. Is propeller damaged? A. Have prope[...]

Trouble Recovery 63 Q. Is heat range of spark plug incorrect? A. Inspect spark plug and replace it with rec- ommended type. Q. Is high pressure fuel pump drive belt bro- ken? A. Have serviced by a Yamaha dealer. Q. Is engine not responding properly to shift lever position? A. Have serviced by a Yamaha dealer. Engine vibrates excessively. Q. Is prop[...]

Trouble Recovery 64 EMU29520 Power trim and tilt will not operate If the engine cannot be tilted up or down with the power trim and tilt/ the power tilt because of a discharged battery or a failure with the power trim and tilt unit/the power tilt, the en- gine can be tilted manually. 1. Loosen the manual valve screw by turn- ing it counterclockwise[...]

Trouble Recovery 65 cord where it could become entangled, preventing it from functioning. ● Avoid accidentally pulling the lanyard during normal operation. Loss of en- gine power means the loss of most steering control. Also, without engine power, the boat could slow rapidly. This could cause people and objects in the boat to be thrown forward. ?[...]

Trouble Recovery 66 the engine. Repeat if necessary. W ARNING EWM00620 Do not install the top cowling when en- gine is running. EMU29760 Treatment of submerged motor If the outboard motor is submerged, immedi- ately take it to a Yamaha dealer. Otherwise some corrosion may begin almost immedi- ately. If you cannot immediately take the outboard motor[...]

67 Consumer information EMU29811 Important warranty information for U.S.A. and Canada[...]

Consumer information 68[...]

Consumer information 69 EMU29830 YAMAHA MOTOR CORPORATION, U.S.A. FOUR-STROKE OUTBOARD MOTOR THREE-YEAR LIMITED WARRANTY[...]

Consumer information 70[...]

Consumer information 71 EMU29840 IMPORTANT WARRANTY INFORMATION IF YOU USE YOUR YAMAHA OUTSIDE U.S.A. OR CANADA[...]

Printed in Japan May 2004–1.5 × 1 ! Printed on recycled paper F50D T50D F60D T60D O WNER’S MANU AL 6C1-28199-10 U .S.A.Edition LIT -18626-06-11 6C1-9-10 Hyoshi 4/28/04 3:48 PM Page 1[...]

YAMAHA MOTOR CO., LTD. MADE IN JAPAN PAYS D'ORIGINE JAPON OUTBOARD MOTOR W ARRANTY REGISTRA TION ENREGISTREMENT DE LA GARANTIE DU MO TEUR HORS-BORD Please complete and mail this card. This information is necessary to accurately register your unit for warranty . V euillez signer ci-dessous pour attester que le montage et l’inspection ont ét?[...]

PLACE POST AGE HERE A T TN: W ARR ANTY DEP ARTMENT Warranty card 2/27/02 11:47 AM Page 2[...]