Zanussi ZAF 42 manuale d’uso

2 GAS HOB MODEL ZAF 42 INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance[...]

3 Important Safety Infor mation You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Installation ● This hob must be installed by qualified personnel, according to the manufacturer ’ s instructions and to the relevant British Standards. ● Any ga[...]

4 F or the User Description of the Hob Page 5 Operation Page 6 Maintenance and Cleaning Page 7 Something Not W orking? Page 8 Service and Spare Parts Page 8 Guarantee Conditions Page 9 This appliance is manufactured according to the following EEC directives: 73/23 EEC - 90/683 EEC - 93/68 EEC - 89/336 EEC - 90/396 EEC, current edition. Contents F o[...]

5 1. Hob T op 2. Rapid Burner 3. Semi-rapid Burners 4. Auxiliary Burner 5. Control knob for back right burner (semi-rapid) 6. Control knob for back left burner (semi-rapid) 7. Control knob for front left burner (rapid) 8. Control knob for front right burner (auxiliary) 9. Electric Ignition Push Button Description of the Hob INSTALLATION Any gas ins[...]

6 HOB BURNERS To light a burner, turn the relevant control knob anticlockwise to maximum position. At the same time push the electric ignition button which is marked with a little spark.. Then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again. When switching on the mains, after installation or[...]

7 Befor e any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply . The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob T op Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little wasing [...]

8 Something Not W orking? SYMPTOM ■ There is no spark when lighting the gas ■ The gas ring burns unevenly SOLUTION ◆ Check that the unit is plugged in and the electrical supply is switched on ◆ Check that the RCCB has not tripped (if fitted) ◆ Check the mains fuse has not blown ◆ Check the burner cap and crown have been replaced correct[...]

9 ZANUSSI GUARANTEE CONDITIONS W e, Zanussi, undertake that if, within 24 months of the date of the purchase, this Zanussi appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition[...]

10 Ignition HT Spark Spark Generator Ispra Control's BF 50046 - 230-240V 0.6 Y A T 120 Spark Gap Fixed OVERALL DIMENSIONS W idth: 580 mm. Depth: 500 mm. Height: 88 mm. W eight: 8 Kg. Burner Dia. Tap By-pass Tap colour 1/100 mm Auxiliary 28 Yellow/Red Semi-rapid 32 Green/Black Rapid 40 Violet/Black Aeration adjustment none Instructions for the [...]

11 Important safety requir ements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE W iring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Par . 2 and B.S. 6891 Current Editio[...]

12 550 470 580 500 55 min. FO 2109 Rectangular cut-out size for hob A) End of shaft with nut B) W asher C) Elbow It is impor tant to install the elbow correctly , with the shoulder on the end of the thr ead, fitted to the hob connecting pipe. Failur e to ensur e the corr ect assembly will cause leakage of gas. FO 0814 Gas Connection Connection to t[...]

13 Building In ON/OFF SWITCH FLEX OUTLET ON/OFF SWITCH FLEX OUTLET FO 0763 FO 0764 30 20 min 60 a b FO 1013 1 2 3 Dimensions are given in mm. Building o v er a cupboar d or dra wer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surfac[...]

14 Electrical connections Any electrical work r equired to install this hob should be carried out by a qualified electrician or competent person, in accor dance with the curr ent r egulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230[...]

15 W iring diagram A. IGNITOR SWITCH B. IGNITOR UNIT B L N 0 1 2 3 4 220/240 A[...]

16 Fault Finding Preliminary Electrical Systems Check A. EARTH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary . a) T est leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (Ohm), check all earth wires for continuity and al[...]

17 Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check fitting of burners Check position of the electrode Check by pass simmer adjusted Light burner manually Check gas supply at burner Check continuity fro[...]

18 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. T o do this, follow the procedure below . - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished[...]

19 Conversion fr om Natural Gas to LPG It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted. The gas rate is adjusted to suit. Method • Ensure that the gas taps are in the 'OFF' position • Isolate the hob from the[...]