English dropdown-ico

Alpha Tool.Com.HK Limited hsg-125 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Alpha Tool.Com.HK Limited hsg-125, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Alpha Tool.Com.HK Limited hsg-125 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Alpha Tool.Com.HK Limited hsg-125. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Alpha Tool.Com.HK Limited hsg-125 should contain:
- informations concerning technical data of Alpha Tool.Com.HK Limited hsg-125
- name of the manufacturer and a year of construction of the Alpha Tool.Com.HK Limited hsg-125 item
- rules of operation, control and maintenance of the Alpha Tool.Com.HK Limited hsg-125 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Alpha Tool.Com.HK Limited hsg-125 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Alpha Tool.Com.HK Limited hsg-125, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Alpha Tool.Com.HK Limited service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Alpha Tool.Com.HK Limited hsg-125.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Alpha Tool.Com.HK Limited hsg-125 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-01 14 www .alpha-tools.com Part No: HSG-125 HSG-225 Alpha ® High-Speed Ang le Grinder Instr uction Manual MANUAL[...]

  • Page 2

    2 T ABLE OF CONTENTS High-Speed Angle Grinder Overview ...........................................................................3 Specifi cations .................................................................................................... 3 Accessories ......................................................................................[...]

  • Page 3

    3 HIGH-SPEED ANGLE GRINDER OVERVIEW SPECIFICA TIONS Power Supply ........................................................... Single-Phase AC, 50 / 60 Hz Rating ............................................................................................ 1 15 / 230 V olts Amperage ......................................................................[...]

  • Page 4

    4 ACCESSORIES COMPONENTS: Protective Cover w/ Clamp Screw (Part No. 130653) Side Handle (Part No. 130433) Inside Flange and Locking Flange Set with 7/8” Arbor (Part No. 136038 & 136039) * Pin spanner Wrench 34 mm (Part No. 130434) Extra Carbon Brush Set (Part No. 136046) Extra Inside Flange & Locking Flange Set with 20mm Arbor (Part No. 1[...]

  • Page 5

    5 INTRODUCTION Thank you for purchasing the Alpha ® High-Speed Angle Grinder . Please read this instruc- tion manual thoroughly to ensure safety and correct use of this tool. Keep this manual in a place where operators can access it easily whenever necessary . ABOUT THE SYMBOLS According to the hazard level, all safety notes in this manual are cla[...]

  • Page 6

    6 CAUTION! The following are important notes for products, operation, and maintenance applicable to this High-Speed Angle Grinder . GENERAL SAFETY RULES WORK AREA Keep your work area clean and well lit . Cluttered benches and dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of fl ammable liq[...]

  • Page 7

    7 Remove adjusting keys or wrenches before turning the tool on . A wrench or a key that is left attached to a rotating part of the tool may result in personal injury . Do not overreach . Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. Do not use on a ladder or uns[...]

  • Page 8

    8 SPECIFIC SAFETY RULES Accessories must be rated for at least the speed recommended on the tool warning label . Wheels and other accessories running over rated speed can fl y apart and cause injury . Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord . Contact wit[...]

  • Page 9

    9 overheating. Below table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number , the heavier the cord. Ampere Rating T otal length of cord in feet (1 15V ) 25ft 50ft 100ft More Than Not More Than A WG 0 6 18 16 16 6 10 18 16 14 10 12 16 16 14 12 16[...]

  • Page 10

    10 • Check grinding tools before use. The grinding wheel must be properly mounted and turn freely . Perform a test run for at least 30 seconds without any load. Do not use damaged, out of round or vibrating grinding tools. • Immediately switch off the machine in case of considerable vibrations or if other malfunctions occur . Check the machine [...]

  • Page 11

    11 action may decrease the rotation speed which reduces the effi ciency of the grinder . 3. Hold the tool with both hands while starting; the torque from the motor will cause the tool to jerk. 4. When the grinding wheel fi rst comes into contact with the work surface or when the wheel is new , make contact slowly . 5. Keep moving the tool in a ci[...]

  • Page 12

    12 Switching off : T o unlock, depress the back of the sliding switch. The switch will automatically move back as shown in Figure 4. BEFORE USE DANGER! Before using the machine, check the following items. In particular , check items 1 to 5 before plugging the power supply cord into the power outlet. 1. Check the working voltage. – Be sure the vol[...]

  • Page 13

    13 W ARNING! 1. Before turning the switch ON, make sure the rotating parts are not touching anything. If the switch is turned ON while they are in contact with anything else, the wheel may get damaged and may cause injuries. 2. When a new wheel is attached and the switch is turned ON, keep your body well away from the exposed sides of the wheel for[...]

  • Page 14

    14 USING THE T OOL PROTECTIVE COVER INST ALLA TION CAUTION! The protective cover should be used to prevent the dust and fl ying debris from hitting the operator or from going inside the tool. Failure to do so can shorten the life of the tool and void the limited warranty . 1. Slide the protective cover onto clamping collar so that the lip on the p[...]

  • Page 15

    15 ASSEMBLING SPINDLE A TT ACHMENTS CAUTION! Do not leave threaded accessories on the spindle of the tool for extended periods of time, as this may result in making it diffi cult to remove these accessories. Note: The Alpha ® High-Speed Angle Grinder has a 5/8”-1 1 spindle thread . It comes with two Inside Flange and Locking Flange sets: 20mm A[...]

  • Page 16

    16 While depressing the spindle button, rotate the spindle until the spindle lock button is inserted into the gear , thus locking the spindle in a fi xed position. With the spindle locked in place, turn the locking fl ange clockwise until hand-tight. Use the 34mm pin spanner wrench to secure tightly . DISASSEMBLING SPINDLE A TT ACHMENTS Please fo[...]

  • Page 17

    17 CHECKING AND REPLACING THE CARBON BRUSHES In order to keep the tool running correctly , you need to check the carbon brushes after every one hundred hours of use. Carbon brushes wear out over time based on the grinder ’s usage. If a carbon brush is worn out, it may cause the motor to malfunction or fail to run. The carbon brushes should be rep[...]

  • Page 18

    18 CARBON BRUSH HOLDER REMOV AL Disconnect the power wire from carbon brush holder . Note: Each grinder has 2 carbon brushes located on opposite sides of each other . 2. Remove the carbon brush holder from the motor housing by pulling the holder out with a pair of needle nose pliers. 3. With the carbon brush holder removed, you can check and clean [...]

  • Page 19

    19 4. Pictured on the left below , is a worn carbon brush in the holder (Note: the twisted wire is at the end of the slot and the carbon brush is almost fl ush with holder) . On the right below , is a new carbon brush in the holder . NOTE: Carbon brushes sometime wear at different rates; however , both carbon brushes should be replaced at the same[...]

  • Page 20

    20 2. Remove the old carbon brush and disconnect the wire terminal. If the inside of the holder is fi lled with dust, clean it before installing the new carbon brush. Upon instal- lation of the new carbon brush, make sure the twisted wire is in the slot and behind wire terminals on the holder (as in Figure 22 right photo). 3. With the carbon brush[...]

  • Page 21

    21 ALPHA ® HIGH-SPEED ANGLE GRINDER SCHEMA TIC (HSG-125)[...]

  • Page 22

    22 ALPHA ® HIGH-SPEED ANGLE GRINDER P ARTS LIST (HSG-125) DRA WING NO. P ART NO. DESCRIPTION PIECES 1 130391 O Ring 16×2 1 2 130390 Lock 1 3 130389 Spring 1 4 130388 Screw M4×7 2 5 130384 Gear Box Assembly 1 6 130458 Needle Bearing HK0709F (7×1 1×9) 1 7 130450 Snap Ring 13.5×1.2 1 8 130426 Lock Flange 1 9 130420 Small Gear+Oil Wiper 1 1 1 130[...]

  • Page 23

    23 ALPHA ® HIGH-SPEED ANGLE GRINDER P ARTS LIST (HSG-125) DRA WING NO. P ART NO. DESCRIPTION PIECES 34 136044 Armature Assembly 1 36 130407 Rear Motor Housing (Blue) 1 37 130376 Insulation Disc 1 38 130657 Condenser Assembly 1 39 130381 Ball Bearing 607-2Z (7×19×6) 1 40 130375 Bearing Sleeve 1 41 130027 Self-tapping Screw 3.9 X9.5 2 42 130026 Ca[...]

  • Page 24

    24 Limited W arranty of Alpha ® High-Speed Angle Grinder for the USA and Canada ONL Y! Alpha Professional T ools ® warrants this product against defects in material and workmanship for a period of 180 days from the date of original retail purchase (proof of purchase required). If Alpha Professional T ools ® receives notice of such defects during[...]

  • Page 25

    25 For more information concerning Alpha ® tool repair service, please contact the Alpha ® regional repair centers listed below: COMP ANY HEADQUARTERS: Alpha Professional T ools ® 103 Bauer Drive Oakland, NJ 07436 Hours of Operation : 8:30 a.m. – 5:00 p.m. EST T elephone Number: 201-337-3343 T oll-Free Number: 800-648-7229 Website: www .alpha-[...]

  • Page 26

    26 EC DECLARA TION OF CONFORMITY Name of Manufacturer: Alpha Professional T ools ® Address of Manufacturer: 103 Bauer Drive Oakland, NJ 07436 U S A Herewith declares that: ELECTRIC HAND T OOL: “High-Speed Angle Grinder” Make: Alpha Professional T ools ® T ype: HSG-125/HSG-225 -Does comply with the provisions of the Low V oltage Directive 73/2[...]

  • Page 27

    27 PRODUCT REGISTRA TION CARD Model No. Serial No. Company Name: ______________________________________________ Name: ______________________________________________________ Address: ____________________________________________________ City: _______________________State: ________Zip: ________________ T elephone: _____________________________________[...]

  • Page 28

    Copyright © 2008 Alpha Professional T ools. All rights reserved. 103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-01 14 www .alpha-tools.com 1 1/2008[...]