AMX Modero NXT-1200V manual

Operation/Reference Guide Touch Panels NXD/T-1200V 12" Modero ® Video Wall/Flush Mount Touch Panel (Composite/S-Video Support) Last Revised: 3/30/2011[...]

AMX Limited Warranty and Disclaimer This Limited W arranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Partn er which include AMX Dealers, Distributors, VIP’s or other AMX authorized entity . AMX warrants its products to be free of defects in material and workmanship under normal use for three (3) ye a[...]

AMX Software License and Warranty Agreement • LICENSE GRANT . AMX grants to Licensee the non-exclusive right to use the AMX Software in the manner described in this License. The AMX Software is licensed, no t sold. This license does not grant Licensee the right to create derivative wor ks of t he AMX Software. The AMX Software consists of general[...]

FCC Information This device complies with Part 15 of the FCC Rules. Operati on is subject to the fol lowing two condition s: (1) this device may not cause harmful interference, and (2) this device must accept any interference rece ived; in cluding in terference that may cause undesi red operation. Federal Communications Commission (FCC) Statement T[...]

Table of Contents i NXD/T-1200V 12" Modero® Vid eo Wall/Flush Mount Touch Panel Table of Contents Introduction .................. ...................................................................... ................ 1 Modero Video Touch Panels (1200V-S eries) ..................... .................... .................... 1 Product Specific[...]

ii NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Table of Contents Installing an N XT-BP into th e NXA-BASE/B ............ ................ ............. ................ .......... 2 4 Charging the NXT -BP batteries with the NXA-BASE /B ................. ................ ................ 25 NXT-CHG Battery Charger Kit (FG2255- 5[...]

Table of Contents iii NXD/T-1200V 12" Modero® Vid eo Wall/Flush Mount Touch Panel Step 4: Usin g a USB to C onfigure a Virtual Master (u sing NetLinx S tudio) ................. .. 5 2 Step 5: Confirm an d View the current AMX USB device connections ......... ................ .. 5 3 Wireless Settings Page - Wireless Access Over view ..........[...]

iv NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Table of Contents Step 2: Upgrad e the NXA-BA SE/B firmware via a n IP ...... ............. ................ ............. ... 83 Firmware Pages and Description s ....................... .............................. ............... 85 Overview ........... ........................[...]

Table of Contents v NXD/T-1200V 12" Modero® Vid eo Wall/Flush Mount Touch Panel @PSP ............ ............ ............ ............ .............. ............ ............ ............ ........... .............. ............ 113 @PST ............ ............ ............ ............ .............. ............ ............ ...........[...]

vi NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Table of Contents ^GIV....... .............. ............ ............ ............... ........... ............ ............ ............... ............ . .......... ... 130 ^GLH .............. ........... ............ ............... ............ ........... ............ ........[...]

Table of Contents vii NXD/T-1200V 12" Modero® Vid eo Wall/Flush Mount Touch Panel @EKP ............ ............ ............ ............... ........... ............ ............ ............... ........... ........... . ........... 146 PKEYP ............. ............ ............ ............... ........... ............ ............ ......[...]

viii NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Table of Contents $BY ........ .............. ............ ............ ............ .............. ............ ............ ............ ............ .... .......... ... 154 $BN ........... ........... ............ ............... ............ ........... ............ .........[...]

Introduction 1 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Introduction AMX has taken a great leap forward with the release of th eir ne w 1200V -Series of Modero touch panels. These panels of fer the ability to display Composite video, 802.11g communication, and USB support for extended input de vices, and panel programming vi[...]

Introduction 2 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Product Specifications (NXD-1200V and NXT-1200V) The following table outlines th e specif ications for 1200V -Ser ies of 12" Modero panels. 1200V Specifications Dimensions (HWD): • NXD-1200V (with faceplate): 12.38" x 12.59 " x 3.25" (31.43 cm x 3[...]

Introduction 3 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel 1200V Specifications (Cont.) Operating /S torage Environments: • Operating T emperature: 10° C (50° F) to 40° C (104° F) • Operating Humidity: 20% to 85% RH • S t orage T emperature: -20° C (-4 ° F) to 60° C (140° F) • S t orage Humidity: 5% to 85% RH In[...]

Introduction 4 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 1200V-Series Modero Connectors FIG. 2 shows the connectors on the 1200V Modero V ideo panels. The Audio/V ideo RJ-45 connector provides differential audio/video si gnals between the touch pane l and the NXA-A VB/ETHERNET . This connector routes Composit e video, Stereo[...]

Touch Panel Accessories 5 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Touch Panel Accessories Overview The following section out lines and describes both the included accessories and other AMX equipment av ailable for thes e touch panels. NXA-AVB/ETHERNET Breakout Box (FG2254-10) The NXA-A VB/ETHERNET Breakout Box (FIG. 3) is i[...]

Touch Panel Accessories 6 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Installing th e NXA-AVB/ETHERNET A 12 VDC-compliant power supply can indirectly pro v ide po wer to a Modero panel by routing po wer through the NXA-A VB/ETHERNET Breakout Box. FIG. 4 shows a sa mple wiring configuratio n using both an indirect or direct po [...]

Touch Panel Accessories 7 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Use a standard CA T5 Ethernet cabl e to provide both communication and 10/100 network connecti vity between the panel, NXA-A VB/ETHERNET , N e tLinx Master , and the network. Wiring the NXA-AVB/ETHERNE T connectors and cables The inputs and outputs on the bre[...]

Touch Panel Accessories 8 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Wiring the NXA-AVB/ETHERN ET for Unbalanc ed Audio Most domestic audio equipment has unbalanced audio inputs and outputs. This means that the audio output (left, right, or mono) appears on a singl e wire, and is refe renced to "0 V" or "Groun [...]

Touch Panel Accessories 9 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Modero Table Top Cable (CA2250-50) The Modero T able T op T ouch Panels come with a st andard 10' (3.048 m) Modero cable (CA2250-50) that supports Ethernet, Audio/V ideo, and Power connect ions. The cable comes terminated with two RJ45 connectors (Ethern[...]

Touch Panel Accessories 10 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Wiring information for th e Modero Table Top cable If your installation requires custom cable configurations, you can purchas e b ulk (non-terminated) cable from Liberty Wire and Cable under the nomenclatur e "AMX T able T op Cable - Moder o" (pho[...]

Touch Panel Accessories 11 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel The follow ing figures pro vide a cross-section view (FIG . 11) and a description (FIG . 12) of the Modero T able T op Cable: FIG. 11 Table Top Cable - cross- section view FIG. 12 Table Top Cable - Specification Elements Element #1 Binder Element #2 Jacket C[...]

Touch Panel Accessories 12 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Installing CAT5 Suppression Ferri tes Before connecting the RJ-45 cables to the panel, inst all the necessary number of CA T5 Suppression Ferrites (FIG. 13) to their appropriate locatio ns. These ferrites co me as part of the Installation Kits mentio ned in[...]

Touch Panel Accessories 13 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel NXA-CFTP Compact Flash (FG2116-2x) Every Modero panel is shipped with tw o factory de fault modules: an EXM Memory Module and a Compact Flash card. These panels are shipped with a 256 memory module which is not upgradeable. The default 128 MB Compact Flash c[...]

Touch Panel Accessories 14 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Product Specif ications NXA-PCI80211G Specifications Dimensions (HWD): • 0.02" x 2.13" x 4.66" (5.0 mm x 54.0 mm x 1 18.4 mm) Weight: • 1.05 oz (30g) Description: • Direct Sequence S pread Spectrum (DSSS)/CCK 802.1 1g Wireless mini-PCI [...]

Touch Panel Accessories 15 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Installation and Upgrade of the Internal NXT Components Upgrading the components within the T a ble T op pane l in volves remo ving the outer housing (with speak er plate), removing and/or installing an existing component, and then plac ing the outer housing[...]

Touch Panel Accessories 16 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 4. Rotate the panel back ov er (while gripping the entire unit with outer housing) and rest th e base on a flat surface. 5. Gently tilt the LCD backw ard to a 45° a ngle. 6. In a single motion , carefully pull the outer housing up and then out (aw ay from [...]

Touch Panel Accessories 17 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel 5. While maintaining the 25° angle alignment on the n ew mo dul e, push it in firmly until the contact pins are completely inside the connector and the card "snaps" into place (FIG. 20). 6. Push the card downw ard (to the main board) until the sid[...]

Touch Panel Accessories 18 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 2. Insert the tip of a grounded flat- head scre wdriv er into one of the card remov al groov e s (located on either side of the existing card), and gently pry the card out of the slot (FIG. 22). Repeat this pr ocess on the opposite card remo v al groov e. T[...]

Touch Panel Accessories 19 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Step 4: Close and Resecur e the NXT Panel Enclosure 1. Obtain the I/O connector plate and s lide it back into position (FIG. 21). 2. Resecure the Stereo Output n ut back onto th e ne w Stereo Output jack onto the I/O plate. 3. W ith the components securely i[...]

Touch Panel Accessories 20 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 5. Unscre w the four pan-head Housing Scre ws from the rear of the NXD unit (FIG. 23) and gently remove the outer housing. These four screws secure the back box to the internal panel casing. Step 2: Install the new 802.11g mini-PCI Wirele ss card (NXD) 1. C[...]

Touch Panel Accessories 21 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Step 4: Close and Resecur e the NXD Panel Enclosur e 1. W ith the components securely inst alled, gently pl ace the outer housing back onto the metallic panel casing (with the connector opening on the right-side of the panel) and align the four pan-head Hous[...]

Touch Panel Accessories 22 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel NXA-BASE/B Battery Base Kit (FG2255K) The NXA-B ASE/B Battery Base is a Modero acce ssory that al lows the Modero T able T op touch panels (NXT) to function off the collecti ve charge of tw o internally connected NXT -BP batteries ( FG2255-10 ). The base pr[...]

Touch Panel Accessories 23 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel 2. Repeat the above step for each NXT -BP battery . 3. Charge the NXT -BP battery by either inserting it into the battery base or from within the optional NXT - CHG charger (which can sequentiall y charge up to tw o batteries). Installing the NXA-BASE/B to a[...]

Touch Panel Accessories 24 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 6. Firmly grip both the panel (from the side) and battery base (fro m belo w) together . 7. Gently place the touch panel LCD facedo wn onto a soft cloth (this prev ents sc ratching of the LCD while the battery base is being secured ). 8. Locate the capti ve[...]

Touch Panel Accessories 25 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel 2. Install the NXT -BP battery . label-side down. 3. Align the battery connectors with the corresponding battery connector por t (located inside the battery compartment), as sho wn in FIG. 30. 4. Insert the NXT -BP battery until the connectors securely fit i[...]

Touch Panel Accessories 26 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel NXT-CHG Battery Charger Kit (FG2255-50K) The NXT -CHG Kit includes one char ger and two batteries. The opti onal NXT -CHG Modero Power Station (FIG. 31) is a two-slot, stand-alone ba ttery charger that can be used to recharge up to two NXT -BP batteries. Th[...]

Touch Panel Accessories 27 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Reading NXT-CHG LED In dicator FIG. 32 shows the components on the NXT -CHG Smart Battery Charger . There is one LED indicator on the front of each battery slot th at indicates th e status of that slot. The blink patterns for these LEDs are descri bed in the[...]

Touch Panel Accessories 28 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel[...]

Installation Procedures: NXD-1200 V Panels 29 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Installation Procedures: NXD-1200V Panels Overview NXT panels are mounted onto flat ( horizontal) surfaces in either a st and-alone or combo (NXT atop an NXA- B ASE/B battery base) confi guration. NXD panels are installed into e ither a pr[...]

Installation Procedures: NXD- 1200V Panels 30 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 6. Remov e the four pan-head Housing Screws from the rear of the NXD unit (FIG. 33). These screws secure the back box to the internal panel casing. 7. Lift the back box housing to sep arate it from the inter nal panel casing. Installing t[...]

Installation Procedures: NXD-1200 V Panels 31 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Cable Installation for the MP-TP12 Back Box 1. Connect the cable connector s (RJ-45, Ethernet, and any other audi o /video wiring) to their respecti ve locations along the side of the touch panel. 2. Thread the incoming cables through the [...]

Installation Procedures: NXD- 1200V Panels 32 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 6. Securely grasp both sides of the NXD panel (with LCD, MB-TP12 back box, and attached cables), rotate the entire unit o ver , and lie it on a flat le vel surf ace. 7. Note the av ailable mounting contact surface area on the rear p lasti[...]

Installation Procedures: NXD-1200 V Panels 33 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Pre-wall Installation of the Conduit Box W all Mount panels (NXDs) are contained within a metallic outer housing (back box). This back box is not rem ove d when installing the NXD into a conduit box (CB-TP12). The back bo x is only remov e[...]

Installation Procedures: NXD- 1200V Panels 34 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 2. Remov e any n ecessary wiring knock outs from the (optional) co nduit box ( C in FIG. 37) where the necessary cables are threaded through for connection to the touch panel. 3. Thread the incoming RJ-45, Ethern et, and an y other audio/[...]

Installation Procedures: NXD-1200 V Panels 35 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel 2. V erify the incoming RJ-45, Ethernet, USB, and any ot her audio/video cables ha ve been properly threaded through the wiring knockouts (from their terminal locations) on the conduit box. Leave enough slack in the wiring to accommodate a[...]

Installation Procedures: NXD- 1200V Panels 36 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 9. Reconnect the terminal RJ -45, Ethernet, USB, and an y optional audio/video wiring to their respecti ve locations ( outside the conduit box ) on either the NXA-A VB/ETHERNET Br eakout Box, Ethernet port, or NetLinx Master . 10. Reconne[...]

Installation Procedures: NXD-1200 V Panels 37 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel 4. Thread the incoming RJ-45, Ethern et, USB, and any other audio/vide o wiring (from their terminal locations) through the cu tout opening. Refer to the W iring Guidelines for the 1200V P anels section on page 41 for pinout descriptions. [...]

Installation Procedures: NXD- 1200V Panels 38 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 11. Place the magneti c faceplate ( A in FIG. 40) back onto the main NXD unit ( B in FIG. 40). Make sur e to align the Micr ophone, Light, and PIR Mo tion sensor locations to their respective openings on the fr ont bezel/faceplate. 12. Re[...]

Installation Procedures: NXD-1200 V Panels 39 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel 4. Thread the incoming RJ-45, Ethern et, USB, and any other audio/vide o wiring (from their terminal locations) through the cu tout opening. Refer to the W iring Guidelines for the 1200V P anels section on page 41 for pinout descriptions. [...]

Installation Procedures: NXD- 1200V Panels 40 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 12. Reconnect the terminal po wer connector on the 12 VDC-compliant po wer supply and apply po wer. Installing an NXD into an (optiona l) Rack Mount Kit (NXA- RK12) 1. Remov e the magnetic faceplate/bezel from the main NXD unit by grippin[...]

Installation Procedures: NXD-1200 V Panels 41 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel 11. Reconnect the terminal RJ-45, Ethernet, and any optional audio/video wi ring to their respectiv e locations on either the NXA-A VB/ETHERNET Break out B ox, Ethernet port, or NetLinx Master . 12. Reconnect the terminal po wer connector [...]

Installation Procedures: NXD- 1200V Panels 42 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Audio/Video Port: Connections and Wiring The following table sho ws the signa l and pinout/pairing information us ed on the RJ-45 Audio and V ideo connections. Refer to the Installing CA T5 Suppression F errites section on page 12 for det[...]

Installation Procedures: NXD-1200 V Panels 43 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel FIG. 46 diagrams the RJ-45 pinouts and signals fo r the Ethernet RJ-45 c onnector and cable. FIG. 46 RJ-45 wiring diagram[...]

Installation Procedures: NXD- 1200V Panels 44 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel[...]

Panel Calibration 45 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Panel Calibration Overview This section outlines the steps fo r calibrating the touch panel. It is r ecommended that you calibrate the panel befor e its initial use and after completing a firmwar e download. Modero panels are factory setup with specif ic demo t ou[...]

Panel Calibration 46 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 2. After the " Calibration Successful.. " message appears, press anywhere on the screen to continue and return to the Setup page. Testing your Calibration 1. Press and hold down the on-screen Calibration b utton for 6 seconds to enter the Calibration T [...]

Configuring Communication 47 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Configuring Communication Overview Communication between the Modero panel and the Master is done using either USB or ETHERNET ( DHCP or Static IP ). Ethernet communication can be achiev ed through either a di rect connection (Ethernet) or through the use o[...]

Configuring Communication 48 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 7. Press the on-screen Reboot button to restart the panel and incorporate any changes. 8. Obtain the System Number and Ma ster IP Address from NetLinx St udio. This information must be specific for the system used wi th the configured Modero panel. 9. Pre[...]

Configuring Communication 49 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Configuring and Using USB with a Virtual Master NetLinx Studio can be setup to run a V irtual Master where the PC acts as the Master by supplying its own IP Address for communication to the pane l. The PC is f irst equipped with the USB driv er, the panel [...]

Configuring Communication 50 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 2. Connect the terminal end of the 12 VDC-compliant po wer supply cabl e to the power connector on the rear/side of the touch panel and then apply power . 3. After the panel po wers-up, press and hol d the grey Front Setup Access button ( f or 3 seconds )[...]

Configuring Communication 51 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel  This windo w notifies you that the panel has been detected by the PC as a USB-compliant device and the PC is installing an appropriate USB dr iv er to establish a pr oper communication to the panel.  The driv er does not contain a Microsoft ®[...]

Configuring Communication 52 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel T o remo ve the USB dri ver association from a pre viously connected touch pa nel, you must navig ate back to the Device Manager , right-click on the panel’ s USB driv er (example AMX USB LAN LINK #2) and select Uninstall from the context menu and then [...]

Configuring Communication 53 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel 4. Click the Communication s Settings button to open the Communications Settings dialog. 5. Click on the NetLinx Master radio b utton ( fr om the Platform Sele ction section ) to indicate that you are working as a NetLinx Master . 6. Click on the V irtual [...]

Configuring Communication 54 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 1. V erify this direct USB connection (T ype-A on the panel to mini-USB on the panel) is conf igured properly using the steps outlined in the pre vious two sections. 2. W ith the panel already c onfigured for USB communication and the V irtual Master set [...]

Configuring Communication 55 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Ethernet Communication from the panel can be direct (using an Ethernet cable) or indirect (through the NXA- PCI80211G AMX W ireless Card ( FG2255-04 ) communicating to a W ireless Access Point (W AP) such as the NXA-W AP200G). In determining the Ethernet m[...]

Configuring Communication 56 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 6. Press Done after you are f inished assigning the alpha-n umeric string of the host name. 7. Do not alter an y of these remaining gre yed-out field s in the IP Settings sect ion. Once the panel is rebooted, these v a lues are obtained by the unit and di[...]

Configuring Communication 57 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel 12. Setup the security and communicati on parameters between the wireless card and the target W AP by configuring the W ireless Settings section on this page. Refer to the foll o wing section for detailed procedures to setup either a secure or inse cure co[...]

Configuring Communication 58 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 10. V erify the fields in the IP S ettings section ha ve been properly conf igured. Refer to Step 1: Conf iguring the P anel’s W ireless IP Settings section on page 55 for detailed information. 11. Press the Back button to na vigate to the Protecte d Se[...]

Configuring Communication 59 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel 7. T ouch the Network Name (SSID) field and from the Service Set Identif ier ke yboard, enter the SSID name you will be using on your targ et W ireless Access Point ( case sensitive ).  The card should be gi ven the SSID used by the tar g et W AP . I[...]

Configuring Communication 60 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel  This keyboard allo ws you to enter a Passphrase (such as AMXP anel ) and then A UTOMA TICALL Y generate a WEP ke y which is comp atible only among Modero panels. 12. W ithin this on-screen WEP Passphr ase keyboard (FIG. 62), en ter a character stri[...]

Configuring Communication 61 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel 15. V e rify the fields within the IP Settings se ction have been properly conf igured. Refer to Step 1: Configurin g the P anel’s W ir eless IP Settings section on page 55 for detailed information . 16. Press the Back button to na vigate to the Protecte[...]

Configuring Communication 62 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 3. T oggle the DHCP/Static field ( from the IP Settings section ) until the choice c ycles to DHCP . 4. Press the optional Host Name f ield to open a K eyboard and enter the Host Name information. 5. Press Done after you are f inished assigning the alpha-[...]

Configuring Communication 63 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Step 2: Choosing a Master Connection Mode Setting There are three Ethernet MODE settings used in the Ma ster Connection section of the System Settings page. URL is the most common method.  Master Connection MODE options: Step 3: Configuring the Ether[...]

Configuring Communication 64 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Master Connection - Virt ual Master communica tion over Ethernet Before beginning: 1. V erify the panel has been configured to communica te either through an Ethe rnet cable (connected from either the panel to a v alid Ethernet Hub) or wireless to the W i[...]

Configuring Communication 65 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel 5. Click on the NetLinx Master radio b utton ( fr om the Platform Sele ction section ) to indicate that you are working as a NetLinx Master . 6. Click on the V irtual Master radio box ( fr om the T ransport Connection Option section ) to indicate you are w[...]

Configuring Communication 66 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Master Connection section - N etLinx Master Ethernet IP Address - URL Mode In this mode, enter the System Number ( zero for an unkno wn System Number) and the IP/URL of the Master (Master Port Number is defaulted to 1319 ). 1. Press the blue Ty p e field [...]

Configuring Communication 67 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel 7. Enter the System and De vice number for the spec if ic Master associated with your panel ( as seen in th e Online T r ee tab ). 8. Click Add and enter the IP Address of th e Modero touch panel into the Add URL dialog box. 9. Click OK to enter your IP Ad[...]

Configuring Communication 68 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Using G4 Web Control to Interact with a G4 Panel The G4 W eb Control feature allows you to use a PC to interact with a G4 enable d panel via the web . This feature works in tandem with the new bro wser- capable NetLinx Securi ty firmw are update ( build 3[...]

Configuring Communication 69 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel 12. From the W eb Password ke yboard, enter a unique al pha-numeric string to b e assigned as the G4 Authentication se ssion password a ssociated with VNC web access of this panel. 13. Press Done after you are finished assigning the alpha-n umeric string f[...]

Configuring Communication 70 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel  If the Master has been previously conf igured for secur ed communication, cl ick OK to accept the AMX SSL certif icate ( if SSL is enabled ) and then enter a valid username and passw ord into the field s within the Login dialog. 4. Click OK to ente[...]

Configuring Communication 71 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel 8. In some cases, you might get a Connection Details dialog (FIG. 72) requesting a VNC Server IP Address. This is the IP Address not the IP of the Master bu t of the target touch pane l. Depending on which method of communication you are using, it can be f[...]

Configuring Communication 72 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel[...]

Upgrading Modero F irmware 73 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Upgrading Modero Firmware Before beginning the Upgrade process:  Setup and conf igure your NetLinx Master . Refer to your particular NetLinx Master instruction manual for detailed setup procedures.  Calibrate and prepare the comm unication pag[...]

Upgradin g Modero Fi rmware 74 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 7. ONL Y AFTER the unit displays the first panel page, THEN insert the mini-USB connector into the Program Port on the panel. It may take a minute for the panel to detect the new connection and send a signal to the PC ( indicated by a gr een System Conn[...]

Upgrading Modero F irmware 75 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel both the system number used in step 7 for the VNM is entered into the Master Connection section of the System Settings page and the panel is restarted. Step 3: Confirm and Upgra de the firmware via t he USB port Use the CC-USB T ype-A to Mini -B 5-wire pr[...]

Upgradin g Modero Fi rmware 76 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 8. Select the panel ’ s Kit file fro m the Files sectio n. 9. Enter the Device v al ue associated with the panel and the System number associat ed with the Ma ster ( listed in the OnLine T r ee tab of the W orkspace window ). The P ort field is gr eye[...]

Upgrading Modero F irmware 77 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel 3. Select Settings > Master Communication Settings from the Main menu to open the Master Communication Settings dialog (FIG. 76). 4. Click the Communication s Settings button to open the Communications Settings dialog. 5. Click on the NetLinx Master ra[...]

Upgradin g Modero Fi rmware 78 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 16. Click Ye s to interrupt the current communication fr om the Master and apply the ne w settings. 17. Click Reboot ( fr om the T ools > Reboot the Master Contr oller dialog ) and wait for the System Master to reboot. The ST ATUS and OUTPUT LEDs sho[...]

Upgrading Modero F irmware 79 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel 4. If the panel firmware bein g used is not current, do wnload t he latest Kit file by f irst logging in to www .amx.com and then navigate to T ech Center > Fi rmware Files and from withi n the Modero section of the web page locate your Moder o panel. [...]

Upgradin g Modero Fi rmware 80 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 8. Enter the Device v al ue associated with the panel and the System number associat ed with the Ma ster ( listed in the OnLine T r ee tab of the W orkspace window ). The P ort field is gr eyed- out. 9. Click the Reboot Device checkbox. This causes the [...]

Upgrading Modero F irmware 81 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel 2. Press the grey Front Setup Access b utton for 3 seconds to open the Setup page. 3. Press the Battery Base button to open the Battery Base page (FIG. 80). Step 2: Upgrade the NXA-BASE/B firmware via USB 1. Complete the procedure s outlined in the Step 1[...]

Upgradin g Modero Fi rmware 82 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 12. As the panel is rebooting, tem porarily unplug the USB connector on the panel until the panel has completely res tarted. 13. Reconnect the USB connector to the panel. 14. Right-click the associated System number an d select Refresh System . This cau[...]

Upgrading Modero F irmware 83 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Step 2: Upgrade the NXA- BASE/B firmware via an IP 1. Click on the OnLine T ree tab in the W orkspace window to vie w the devices on the System. The default System value is one . 2. Right-click the a ssociated System numbe r (from the W orkspace) and se l[...]

Upgradin g Modero Fi rmware 84 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel 7. Select the batte ry base’ s Kit f ile ( ending in VXX.kit ) from the Files section (FIG. 82). 8. Enter the Device v al ue associated with the panel and the System number associat ed with the Ma ster ( listed in the OnLine T r ee tab of the W orkspa[...]

Firmware Pages and Desc riptions 85 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Firmware Pages and Descriptions Overview This section describes each firmware page and their sp ecif ic functional elements. Setup Navigation Buttons These Setup Navigation Buttons (FIG. 83) appear on the left of the pane l screen when the Setup pag[...]

Firmware Pages and Descripti ons 86 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Setup Page This page (FIG. 84) centers around basic Modero panel properties such as: Connecti on Status of the pan el, Display T imeout, Inacti vity Page Flip T ime, Inacti vity page fi le, and the Pa nel Brightness. The elements of the Setup page [...]

Firmware Pages and Desc riptions 87 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Project Informati on Page The Project Information page displays the TPDesign4 (TPD4) project f ile propertie s currently loaded on the selected Modero panel (FIG. 85). Refer to the TPDesign4 T ouch P anel Pr ogra m instruction manual for more specif[...]

Firmware Pages and Descripti ons 88 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Panel Information Page The Panel Information page (FIG. 86) centers around Modero panel prope rties such as: resolution used, on- board memory , firmw are, address/channel info rmation, and st ring info rmation. The elements of the Panel Informatio[...]

Firmware Pages and Desc riptions 89 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Time & Date Setup Page The T ime & Date Setup page (FIG. 87) allo ws you to alter/set the tim e and date informat ion on th e NetLinx Master . If either the Time/Date is modified on this page ( then updated to the Master by pressing the Set [...]

Firmware Pages and Descripti ons 90 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Volume Page The V olume page (FIG. 88) ( accessed by pressing the A udio Adjustments button on the Setu p page ) allo ws you to adjust the master v olume parameters and def ault panel sounds on the panel. The elements of the V olume page are descri[...]

Firmware Pages and Desc riptions 91 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Supported sampling rates for WAV The follo wing is a listing of supporte d sampling rates associated for W A V files played on these panels. Some W A V files currently played on Modero's may not w ork on these panels. The supported sampling rat[...]

Firmware Pages and Descripti ons 92 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Video Adjustment - Video Adjustment Page The V ideo Adjustment page (FIG. 90) ( accessed by pr essing the V ideo Ad justment button on the Setup page and then selecting the appr opriate button fr om the option bar ) sets the V ideo propertie s of t[...]

Firmware Pages and Desc riptions 93 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Battery Base Page This page (FIG. 91) allo ws you to alte r/set the po wer warning preferences, monitor battery stat us information, and alter the display times for the ba ttery warnings. The fields on this page are populated with information after [...]

Firmware Pages and Descripti ons 94 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Battery Base Page Elements (Cont.) V ery Low Batter y Warning: T he V ery Low Bat tery W arning UP/DN buttons alter the time value (in minutes) available on the battery (for use) before the panel displays a very low battery warning. This indicates [...]

Firmware Pages and Desc riptions 95 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Protected Setup Navigation Buttons The Protected Setup Navigati on Buttons (FIG. 92) appear on the left of the panel scre en when the Protected Setup page is currently activ e. These Navi gation Buttons are spe cific to these Modero panels and inclu[...]

Firmware Pages and Descripti ons 96 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Protected Setup Page The Protected Setup page (FIG. 93) centers around the properties used by the pane l to properly communicate with the NetLinx Master . Enter the factory default password ( 1988) into the password keypad to access this page. The [...]

Firmware Pages and Desc riptions 97 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Protected Setup Page Elements (Cont.) System Re covery: Allows you to either reset the touch panel to factory default settings and/or wipe out all existing touch panel pages: • The Reset System Settings button allows a user to wipe out all current[...]

Firmware Pages and Descripti ons 98 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel G4 Web Control Page The G4 W eb Control page (FIG. 96) centers around enab ling and disabling both the display and control of your panel (via the web). An e xte rnal PC running a VNC client ( installed during the initial communication to the G4 pan[...]

Firmware Pages and Desc riptions 99 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Refer to the Using G4 W eb Contr ol to Interact with a G4 P anel section on page 68 for more detailed instructions on how to use the G4 W eb Control page with the new web-based NetL inx Security application. Sensor Setup Pag e The Sensor Setup page [...]

Firmware Pages and Descripti ons 100 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel The elements of the Sensor Setup page ar e described in the table be low: A light level value between the Minimum and Maximum DIM Mode valu es delivers an average light level. The DIM mode Min L evel can never exceed the DIM Mode Max Level. Sensor[...]

Firmware Pages and Desc riptions 101 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Using the Automated Brightness Control feature (DIM Mode) Please follo w the steps belo w to set up Automated Brightness Control: 1. Set the lighting conditions in the room to maximum (turn On all the lights). 2. Set the Maximum Panel Brightness, f[...]

Firmware Pages and Descripti ons 102 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Password Setup Page The Password Setup page (FIG. 99) centers around the pr operties used to assign passwords for the Modero panel pages. The elements of the Password Setup page ar e described in the table belo w: Calibration Page This page (FIG. [...]

Firmware Pages and Desc riptions 103 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Wireless Settings Page The W ireless Settings page (FIG. 101) sets the communication informat ion for the installed wireless interface card. This information includes its corresponding IP communication parameters, wire less communication settings, [...]

Firmware Pages and Descripti ons 104 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Wireless Settings Page Elements (Cont.) IP Settings (Cont.): Gateway Sets a gateway value to the panel. • Gateway is a computer that either performs protocol conversion betwe en different types of networks/applications or acts as a go-between fo[...]

Firmware Pages and Desc riptions 105 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Wireless Settings Page Elements (Cont.) Wireless Settings (Cont.): Encryption Cycles through the available encryption options: Clear T ext, WEP64, and WEP128 . Wired Equivalent Privacy is an 802. 1 1 security protocol for wireless networks. The WEP[...]

Firmware Pages and Descripti ons 106 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Wireless Settings Page Elements (Cont.) Wireless Settings (Cont.): WEP Keys This feature provides you with anot her level of security by selecting a Key value. • A single button is available for each WEP key up to a maximum of four keys. • Pus[...]

Firmware Pages and Desc riptions 107 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel System Settings Page The System Settings page (FIG. 102) sets the Secondary DNS Addres s information with its corresponding IP communication parameters, Ne tLinx Master communication settings, a nd reads the de vice number assigned to the Modero pa[...]

Firmware Pages and Descripti ons 108 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Refer to the Step 2: Choosing a Master Connection Mode Setting section on page 63 for more detailed information on using the System Settings page. System Settings Page Elements (Cont.) Primary DNS Sets the address of the primary DNS server used fo[...]

Programming 109 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Programming Overview Y ou can program the touch panel, using the commands in this secti on, to perform a wide vari ety of operations using Send_Commands and v ariable text commands. A device must f irst be defined in the NetLinx programming language with values f or th[...]

Programming 110 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Page Commands (Cont. ) @DPG Delete a specific popup page from specified popup group if it exists. Syntax: "'@DPG-<popup page name>;<popup group name>'" Va r i a b l e : popup page name = 1 - 50 ASCII characters. Name of the popup page. [...]

Programming 111 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Page Commands (Cont.) @PP A Close all popups on a specified page. If the page name is empty , the current page is used. Same as the ’Clear Page’ command in TPDesign4. Syntax: "'@PPA-<page name>'" Va r i a b l e : page name = 1 - 50 ASCII c[...]

Programming 112 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Page Commands (Cont. ) @PPM Set the modality of a specific popup page to Modal or NonModal. A Modal popup page, when active, only allows you to use the buttons and featur es on that popup page. All other buttons on the panel page are inactivated. Syntax: "'@[...]

Programming 113 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Page Commands (Cont.) @PSP Set the show effect position. Only 1 coordinate is ever needed for an effe ct; however , the command will specify both. This command sets the location at which the effect will begin at. Syntax: "'@PSP-<popup page name>;<x c[...]

Programming 114 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Programming Numbers The following information pro vides the program ming numbers for colors, fonts, and borders. Colors can be used to set the colors on buttons, slider s, and pages. The lo west co lor number represents the lightest color-specif ic display; the highes[...]

Programming 115 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel RGB Values for all 88 Basic Colors (Cont.) Index No . Name Red Green Blue 16 Dark Y ellow 127 127 0 17 V er y Dark Y ellow 95 95 0 18 V ery Light Lime 128 255 0 19 Light Lime 1 12 223 0 20 Lime 96 191 0 21 Medium Lime 80 159 0 22 Dark Lime 64 127 0 23 V ery Dark Lime 4[...]

Programming 116 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Font Styles and ID Nu mbers Font styles can be used to prog ram the text fonts on b uttons, sliders, and pages. The following chart sh ows the default font type and th eir respecti ve ID numbers generated by TPDesign4. Border styles The TPDesign4 T ouch Pa nel Design [...]

Programming 117 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel TPD4 Border Styles by Name (Cont.) Border styles Bor der styles Circle 15 Fuzzy Circle 25 Glow-L Circle 35 Help Down Circle 45 Help Down Reversed Circle 55 Menu Bottom Roun ded 15 Circle 65 Menu Bottom Roun ded 25 Circle 75 Menu Bottom Roun ded 35 Circle 85 Menu Bottom[...]

Programming 118 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel "^" Button Commands These Button Commands are used in Ne tLinx Studio and are case insensitive. All commands that begin with " ^ " hav e the capability of assigning a variable te xt address range and button state range. A device must first be def i[...]

Programming 119 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel "^" Button Commands (Cont.) ^B A T Append non-unicode text. Syntax: "'^BAT-<vt addr range>,<button states range>,<new text>'" Va r i a b l e : variable text address range = 1 - 4000. button states range = 1 - 256 for mult[...]

Programming 120 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel "^" Button Commands (Cont .) ^BCF Set the fill color to the specified color . Only if the specified fill color is not the same as the cu rrent color . Note : Color can be assigned by color name (without spaces), number or R,G ,B value (RRGGBB or RRGGBBAA). S[...]

Programming 121 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel "^" Button Commands (Cont.) ^BFB Set the feedback type of the button. ONL Y works on General-type buttons. Syntax: "'^BFB-<vt addr range>,<feedback type>'" Va r i a b l e : variable text address range = 1 - 4000. feedback type [...]

Programming 122 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel "^" Button Commands (Cont .) ^BMC Button copy command. Copy attributes of the source button to all the destination buttons. Note that the source is a single button state. Each state must be copied as a separate command. The <codes> section represents w[...]

Programming 123 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel "^" Button Commands (Cont.) ^BMF Set any/all button parameters by sending embedded codes and data. Syntax: "'^BMF-<vt addr range>,<button states range>,<data>'" Va r i a b l e s : variable text address char array = 1 - 40[...]

Programming 124 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel "^" Button Commands (Cont .) ^BMF (Cont.) ’%GI<bargraph invert>’ = Set the bargraph invert/noninvert or joystick coordinate (0,1,2,3). ^GIV section on page 130 more information. ’%GU<bargraph ramp up>’ = Set the bargraph ramp up time in i[...]

Programming 125 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel "^" Button Commands (Cont.) ^BMP Assign a picture to those buttons with a defined address range. Syntax: "'^BMP-<vt addr range>,<button states range>,<name of bitmap/ picture>'" Va r i a b l e : variable text address rang[...]

Programming 126 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel "^" Button Commands (Cont .) ^BOR Set a border to a specific border style associated with a border value for those buttons with a defined address range. Refer to theTPD4 Border Styles by Name table on page 1 16 for mor e information. Syntax: "'^BOR[...]

Programming 127 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel "^" Button Commands (Cont.) ^BRD Set the border of a button state/ states. Only if the specified border is not the same as the current border . The border names are available through the TPDesign4 borde r-name drop-down list. Syntax: "'^BRD-<vt a[...]

Programming 128 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel "^" Button Commands (Cont .) ^BVN Set the computer control remote host for the specified address. Syntax: SEND_COMMAND <DEV>,"'^BVN-<vt addr range>,<remote host>'" Va r i a b l e s : variable text address range = 1 - 400[...]

Programming 129 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel "^" Button Commands (Cont.) ^DPF Delete page flips from button if it already exists. Syntax: "'^DFP-<vt addr range>,<actions>,<page name>'" Va r i a b l e : variable text address range = 1 - 4000. actions = Stan [dardPage[...]

Programming 130 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel "^" Button Commands (Cont .) ^GIV Invert the joystick axis to move the origin to another corner . Parameters 1,2, and 3 will cause a bargraph or slid er to be inverted regardless of orientation. Their effect will be as described for joysticks. Syntax: "[...]

Programming 131 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel "^" Button Commands (Cont.) ^GSC Change the bargraph slider color or joysti ck cursor colo r . A user can also assign the color by Na me and R,G ,B value (RRGGBB or RRGGBBAA). Syntax: "'^GSC-<vt addr range>,<color value>'" Va r[...]

Programming 132 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel "^" Button Commands (Cont .) ^JSB Set bitmap/ picture alignment using a numeric keypad layout for those buttons with a defined address range. The alignment of 0 is followed by ',<left>,<top> '. The left and top coordinates are relative [...]

Programming 133 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel "^" Button Commands (Cont.) ^JST Set text alignment using a numeric keypad layout for those buttons with a defined address range. The alignment of 0 is followed by ',<left>,<top> '. The left and top coordinates are relative to the upper [...]

Programming 134 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel "^" Button Commands (Cont .) ^SKT Receive touch information on specified socket. Syntax: '^SKT-<0=disable socket, greater than 1023=enable socket on specified port> Only socket values equal to or greater t han 1024 are valid. T he panel will open [...]

Programming 135 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Text Effect Names The follo wing is a listing of te xt ef fects names. This list is associate d with the ^TEF command on page 134. "^" Button Commands (Cont.) ^UNI Set Unicode text. For the ^UNI command (%UN and ^BMF command), the Unicode text is sent as ASCI[...]

Programming 136 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Button Query Commands Button Query commands reply back with a custom ev ent. There will be one custom event for each button/state combination. Each query is assi gned a unique custom ev ent type. The f ollowing example is f or debug purposes only: NetLinx Example: CUS[...]

Programming 137 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Button Query Commands ?BCB Get the current border color . Syntax: "'?BCB-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000. button states range = 1 - 256 for multi-state buttons (0 = All stat[...]

Programming 138 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Button Query Commands (Cont.) ?BCT Get the current text color . Syntax: "'?BCT-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000. button states range = 1 - 256 for multi-state buttons (0 = A[...]

Programming 139 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Button Query Commands (Cont.) ?BOP Get the overall button opacity . Syntax: "'?BOP-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000. button states range = 1 - 256 for multi-state buttons (0 [...]

Programming 140 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Button Query Commands (Cont.) ?BWW Get the current word wrap flag status. Syntax: "'?BWW-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000. button states range = 1 - 256 for multi-state butt[...]

Programming 141 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Button Query Commands (Cont.) ?ICO Get the current icon index. Syntax: "'?ICO-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000. button states range = 1 - 256 for multi-state buttons (0 = All[...]

Programming 142 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Button Query Commands (Cont.) ?JSI Get the current icon justification. Syntax: "'?JSI-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000. button states range = 1 - 256 for multi-state buttons[...]

Programming 143 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Button Query Commands (Cont.) ?TEC Get the current text effect color . Syntax: "'?TEC-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000. button states range = 1 - 256 for multi-state buttons [...]

Programming 144 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Panel Runtime Operations Serial Commands are used in the AxcessX T erminal Emul ator mode. These commands are case insensiti ve. Button Query Commands (Cont.) ?TXT Get the current text information. Syntax: "'?TXT-<vt addr range>,<button states range[...]

Programming 145 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Panel Runtime Operatio n Commands (Cont.) AKEYB Pop up the keyboard icon and initialize the tex t string to that specified. Keyboard string is set to null on power up and is stored until power is lost. Syntax: "'AKEYB-<initial text>'" Va r i a[...]

Programming 146 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Panel Runtime Operatio n Commands (Cont.) BRIT Set the panel brightness. Syntax: "'BRIT-<brightness level>'" Va r i a b l e : brightness level = 0 - 100. Example: SEND COMMAND Panel,"'BRIT-50'" Sets the brightness level to[...]

Programming 147 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Panel Runtime Operatio n Commands (Cont.) SETUP Send panel to SETUP page. Syntax: "'SETUP'" Example: SEND COMMAND Panel,"'SETUP'" Sends the panel to the Setup Page. SHUTDO WN Shut down the batteries providing power to the panel. [...]

Programming 148 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Input Commands These Send Commands are case insensitiv e. Panel Runtime Operatio n Commands (Cont.) @VKB Popup the virtual keyboard. Syntax: "'@VKB'" Example: SEND COMMAND Panel,"'@VKB'" Pops-up the virtual keyboard. W AKE Force[...]

Programming 149 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Input Command s (Cont.) ^SL T Send a command to a given slot. These commands are directed at the video ca rd subsystems. Slot comm ands contain a series of name/value pairs separated by commas. These commands are case insensitive. Syntax: "’^SLT-<slot number&[...]

Programming 150 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Embedded Codes The following is a list of G4 compatible embedded codes: Embedded Codes Decimal numbers Hexidecimal values V ir tual keystrok e 8 ($08) Backspace 13 ($0D) Enter 27 ($1B) ESC 128 ($80) CTRL key down 129 ($81) AL T key down 130 ($82) Shift key down 131 ($[...]

Programming 151 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Panel Setup Commands These commands a re case insensiti ve. Panel Setup Commands ^MUT Set the panel mute state. Syntax: "'^MUT-<mute state>'" Va r i a b l e : mute state= 0 = Mute Off and 1 = Mute On. Example: SEND_COMMAND Panel,"'^M[...]

Programming 152 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Dynamic Image Commands The following table describe s Dynamic Image Commands. Dynamic Image Commands ^BBR Set the bitmap of a button to use a par tic ul a r resource. Syntax: "'^BBR-<vt addr range>,<button states range>,<resource name>&apos[...]

Programming 153 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel ^RAF, ^RMF - Embedded Codes The ^RAF and ^RMF commands add and modify any and all resource pa rameters by sending embedded codes and data: "'^RAF-<resource name>,<data>'" "'^RMF-<resource name>,<data>'" Th[...]

Programming 154 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Escape Sequences The ^RAF and ^RMF commands support the replacement of any special escape se quences in the filename (specif ied by the %F embedded code) with the corre sponding data obtained from the system as outlined in the table below: For instance, http://www .am[...]

Appendix 155 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Appendix Text Formatting Codes for Bargraphs/Joysticks T ext formatting codes for bar graphs pro vide a mechan ism to allow a portion of a bar graphs text to be dynamically provided in formation about the current status of the le vel (multistate and traditional). These co[...]

Appendix 156 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Text Area Input Masking T ext Area Input Masking can be used to limi t the allowed/correct characters that are ent ered into a text area. For e xample, in working with a zip code, a user could limit the entry to a max length of only 5 charact ers but, with input masking,[...]

Appendix 157 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Input Mask Ranges These ranges allo w a user to specify the minimum and maximum numeric v alue for a field. Only one range is allo wed per field. Using a range im plies a numeric entry ONL Y . An example from the abov e table: [0|255] This allows a user to enter a v alue [...]

Appendix 158 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel When data ov erflows from a numerical field, the ov erflo w value is added to the pre vious field on the chain, if the ov erflo w character w as specif ied. In the abo ve example, if the o verfl o w flag was set, the f irst exam ple will place the "1" into the [...]

Appendix 159 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Special Esca pe Sequences The system has only a limited kno wledge of URL formats in that it transparently passes the URL information onto the server for translation. A user can then pass an y parameters to the server side programs such as CGI scripts or activ e server pa[...]

Appendix 160 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel[...]

Troubleshooting 161 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Troubleshooting Overview This section describes the solutions to possible hardware/firmware issues that could arise during the common operation of a Modero touch panel. Troubleshooting Information Symptom Solution Manifest.xma can not b e found. An error occurs whe[...]

Troubleshooting 162 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Troubleshooting Information (Cont.) Symptom Solution I updated my panel firmware but my Battery Base page doesn’t seem to be working properly . • Cycle power manually to the panel and check the Battery Base page after startup. • If downloading the firmware t[...]

Troubleshooting 163 NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Troubleshooting Information (Cont.) Symptom Solution I can’t seem to completely cha rge my batteries from within an NXA-BASE/B connected to a power supply . NXT -BP batteries can be charged from either an external N XT -CHG battery charger or from within the NXA-[...]

Troubleshooting 164 NXD/T-1200V 12" Modero® Video Wall/Flush Mount To uch Panel Troubleshooting Information (Cont.) Symptom Solution After downloading a panel file or firmware to a G4 device, the panel behaves strangely . Symptoms include: • Having to repeat the download. • Inability to make further downloads to the panel. May get "d[...]

Troubleshooting 165 NXD/T-1200V 12" Modero® Vid eo Wall/Flush Mount Touch Panel[...]

3/11 © 2011 AMX. All rights reserved. AMX and the AM X logo are register ed trademarks of AMX. AMX reserves the right to alter specifica tions without notice at any time. It’s Your World - Take Con trol™ 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.222.0193 • 469.624.8000 • 469-624-7153 fax • 800.932.6993 technical support • w[...]