AMX MVP-5200I manual

Operation/Reference Guide Mio Modero Touch Panels MVP-5200i Modero® Viewpoint Widescreen Touch Panel Initial Release: 4/28/2008[...]

AMX Limited Warranty and Disclaimer All products returned to AMX requ ire a Return Mate rial Authorization (RMA) number . The RMA number is obtained from the AMX RMA Department. The RMA number must be clear ly marked on the outside of each box. The RMA is valid for a 30-day period. After the 30-day period the RMA will be cance lled. Any shipments r[...]

Software License and Warranty Agreement • LICENSE GRANT . AMX grants to Licensee the non-exclusive right to use the AMX Software in the manner described in this License. The AMX Software is licensed, no t sold. This license does not grant Licensee the right to create derivative wor ks of t he AMX Software. The AMX Software consists of generally a[...]

[...]

Table of Contents i MVP-5200i Modero Viewpoint Widescreen Touch P anel Table of Contents Introduction .................. ...................................................................... ................ 1 Memory ...................... ......................... ........................ ......................... .................... 4 Connector[...]

ii MVP-5200i Modero Viewpoint Widescreen Touch Panel Table of Contents Configuring Communication ......... ..................................................... ............... 23 IR Communication ........ ......................... ........................ ......................... ................. 25 "Find Me" Function .................[...]

Table of Contents iii MVP-5200i Modero Viewpoint Widescreen Touch P anel Panel Information Page......... ......................... ........................ .............................. ... 63 Time & Date Setup Page .......................... ........................ ......................... ............. 64 Audio Adjustments/Volume Page ....[...]

iv MVP-5200i Modero Viewpoint Widescreen Touch Panel Table of Contents Panel Setup Commands .............. ......................... ............................. .................... 146 Dynamic Image Commands ............................. ............................. ......................... 147 Browser-Based User Pages ..... ..................[...]

Introduction 1 MVP-5200i Modero Viewpoint Widescreen Touch Panel Introduction The MVP-5200i Modero ® V iewpoint ® W idescre en T ouch Panel is AMX’ s smallest and most po werful wireless handheld panel, available in black ( FG5966-01 ) (FIG. 1) and white ( FG5966-02 ). The MVP- 5200i is a wireless-only ergonomic de vice capabl e of V oice Over [...]

Introduction 2 MVP-5200i Modero Viewpoint Widescreen Touch Panel The MVP-5200i comes with an integrated rear "kicks tand", allowing it to be used and displayed aw ay from a Charging Station if necessary (FIG. 2). It also comes with a pre-installed 802.11g WP A/WP A2 SDIO wireless card. FIG. 2 MVP-5200i side view (with kickstand) MVP-5200i[...]

Introduction 3 MVP-5200i Modero Viewpoint Widescreen Touch Panel MVP-5200i Specifications (FG 5966-01, FG5966-02) (Cont.) Memory: • 128 MB Mobile DDRAM (upgrade not available) • 256 MB NAND Flash (upgrade not available) Panel LCD Parameters: • Size: 5.2" (13.21 cm) • T ype: WVGA • Aspect ratio: 16 x 9 • Brightness (luminance): 300 [...]

Introduction 4 MVP-5200i Modero Viewpoint Widescreen Touch Panel Memory The MVP-5200i comes with 128MB of Mobile DDRAM memory and 256 MB N AND Flash memory . Neither may be upgraded. Table Charging Statio n Connector Locations W ith the unit facing you, the mini-USB port (for programming and downloading f irmware as well as connecting USB headphone[...]

Introduction 5 MVP-5200i Modero Viewpoint Widescreen Touch Panel Basic Operation The MVP-5200i is operated using both its integral tou chscreen and the na vigation wheel on the right side of the de v ice. If the de vice has gone into its Sta ndby Mode, a touch of the touchscreen or of the button wheel will reactiv ate it. The MVP-5200i de vice ’ [...]

Introduction 6 MVP-5200i Modero Viewpoint Widescreen Touch Panel Stylus The MVP-5200i comes with a unique touchscreen stylus that slides into a storage groove on the right side of the device when not in use. Replacem ent styluses may be ordered in a 3-pac k ( FG5966-30-xx ) from www .amx.com . Kick Stand Since the MVP-5200i device is designed to be[...]

Accessories 7 MVP-5200i Modero Viewpoint Widescreen Touch Panel Accessories Table Charging Station The MVP-5200i de vice comes with the MVP-TCS-52 T able Charging Station ( FG5966-1X ) (FIG . 5), which acts both as a charging station and a direct po wer connection. The charging station is av ailable in either white ( FG5966-10 ) or black ( FG5966-1[...]

Accessories 8 MVP-5200i Modero Viewpoint Widescreen Touch Panel 4. Place the touch panel in the Charging Station cradle (FIG. 6), guiding it into place with the locking groov es on each side of the cradle (FIG. 7). When fully seated, the touch panel’ s charging station connector should be in contact w ith the Charging Station’ s charger pins. C[...]

Accessories 9 MVP-5200i Modero Viewpoint Widescreen Touch Panel Wall Charging Station The optional MVP-WCS-52 W all Charging Station ( FG5966-1X ) offers the same recharging and connection features as the T able Char ging Station, with the advantage of being placed within accessible locations where the table station is either incon ven ient or impr[...]

Accessories 10 MVP-5200i Modero Viewpoint Widescreen Touch Panel The MVP-5200i touch panel remains locked in the MVP-WCS-52 until unlocked by th e user . This may be done by entering an a ppropriate password (please refer to the P asswor d Settings P ag e section on page 88 for more information), or b y pressing the S ecurity Release button on the [...]

Accessories 11 MVP-5200i Modero Viewpoint Widescreen Touch Panel Unlocking the touch panel Once placed within the W all Char ging Station, the MVP-5200i remains secured until the user unlocks it. T o release the touch panel from the W all Charging Station: 1. Press the Security Release button. 2. A password keypad will pop up on the MVP-5200i scre [...]

Accessories 12 MVP-5200i Modero Viewpoint Widescreen Touch Panel Installing the MVP-WCS-52 Since the W all Charging Station is intended to be af fixed to a w all or other permanent structure, care must be taken to ensure its proper installation to pre vent potential damage to the MVP-5200i placed within. Installing the Pl astic Conduit Box The plas[...]

Accessories 13 MVP-5200i Modero Viewpoint Widescreen Touch Panel 3. Run the power cable through the knockout into the conduit box. Pull out about six in ches (15.25cm) of cable into the conduit box to facilitate installation of the MVP-WCS-52. 4. Slide the plastic conduit box into the hole, being careful not to twist or pinch the cable, and set it [...]

Accessories 14 MVP-5200i Modero Viewpoint Widescreen Touch Panel 7. Secure the power cable to the device, using either of the two tie-wrap anchors included in the Installation Kit at the top rear of the de vice (FIG . 12). Point the head of each tie wrap to ward the center of the device. 8. Firmly seat the mini-captiv e wire conn ector to the po we[...]

Accessories 15 MVP-5200i Modero Viewpoint Widescreen Touch Panel 11. After fully seating the screws, wipe do wn the area around the screw holes with the alcohol prep pad from the Installation Kit. T ake a rubber foot and remove its adhesi ve backing. Put the foot, adhesiv e- side down, in the slot surrounding the screw hole in the W all Charging St[...]

Accessories 16 MVP-5200i Modero Viewpoint Widescreen Touch Panel Installing the Option al Metal Conduit Box The optional metal conduit box (FIG. 14) is 10 inches wide at its widest dimension, and is intended to be used in conjunction with the plastic conduit box in circumstances where additional support is need ed for the W all Charging Station. Th[...]

Configuring Communication 17 MVP-5200i Modero Viewpoint Widescreen Touch Panel Configuring Communication All control for a MVP-5200i touch panel is established through a NetLinx Master . Communication between the MVP and the Master consists of using eith er W ireless Ethernet (DHCP , Static IP) or USB. References to Ethernet in this ma nual focus o[...]

Configuring Communication 18 MVP-5200i Modero Viewpoint Widescreen Touch Panel IR Communication In certain situations, the MVP-5200i may be used as an infrared remote device for other AMX controllers. The de vice can transmit IR ov er 20 feet (6.10 m) fro m the panel at frequencies of 38KHz, 455KHz, and 1.2MHz. IR receivers and transmitters on G4 p[...]

Configuring Communication 19 MVP-5200i Modero Viewpoint Widescreen Touch Panel Modero Setup and System Settings All AMX Modero panels, including the MVP-5200i, feat ure on-board Setup page s. Use the options in the Setup pages to access panel information and make v arious configuration changes. Accessing the Setup and Protected Setup Pages 1. At an[...]

Configuring Communication 20 MVP-5200i Modero Viewpoint Widescreen Touch Panel Setting the Panel’ s Device Number In the Pr otected Setup page: 1. Press the De vic e Number field in the De vice ID section to open the Device Number keypad. 2. Enter a unique Device Number assignment for the de vice , a nd press Done to return to the Pr otected Setu[...]

Configuring Communication 21 MVP-5200i Modero Viewpoint Widescreen Touch Panel Configuring Wireless Network Access The first step in connecting the MVP-5200i to a wireless network is to configure the wireless communication parameters within the device’ s W ir eless Settings page. This page only configures the card to communicate to a target W AP:[...]

Configuring Communication 22 MVP-5200i Modero Viewpoint Widescreen Touch Panel 6. Set up the security and communication parameters between the wireless card and the target W AP by configuring the W ir eless Settings section on this page. Refe r to Step 2: Configur e the Car d’s W ir eless Security Settings section on page 25 for detailed procedur[...]

Configuring Communication 23 MVP-5200i Modero Viewpoint Widescreen Touch Panel Using the Site S urvey tool This tool allows a user to "snif f out" all transmitting Wireless Access Points within the detection range of the internal wireless card (FIG. 20). Once the Site Survey b utton is pressed, th e device displays the Site Surve y page, [...]

Configuring Communication 24 MVP-5200i Modero Viewpoint Widescreen Touch Panel 4. Select a desired Access Point by touching the corresponding row . The up arrow and do wn a rro w will be grayed out if ten or fewe r access points are detected. If more are detected, then the y will be enabled as appropriate so that the user can scroll through the lis[...]

Configuring Communication 25 MVP-5200i Modero Viewpoint Widescreen Touch Panel Step 2: Configure the Card’s Wireless Security Settings The second step in setting up the wireless card is to configure the W ireless Settings section of the W ir eless Settings page. This section configures both the communication and security parameters from the inter[...]

Configuring Communication 26 MVP-5200i Modero Viewpoint Widescreen Touch Panel 3. From within the W ireless Security section, press the Open (Clear T ext) button to open the Open (Clear T ext) Settings dialog (FIG. 23). An Open security method does not utilize any encryption methodology , but doe s require that an alpha-numeric SSID be entered. Thi[...]

Configuring Communication 27 MVP-5200i Modero Viewpoint Widescreen Touch Panel Automatically setting SSID In the Pr otected Setup page: 1. Select W ireless Settings . 2. Press the Site Surv ey b u tton at the bottom of the page. 3. Select a WEP secured W AP from within the Site Surve y page, and press the Connect button (FIG. 24 ). . 4. If the secu[...]

Configuring Communication 28 MVP-5200i Modero Viewpoint Widescreen Touch Panel 3. Press the Static WEP b utton to open the Static WEP Settings dialog (FIG. 26). 4. Press the SSID f ie ld. From the Network Name (SSID) keyboard, enter the SSID name used by the target W ireless Access Point ( case sensiti ve ), and press Done when f inished.  The c[...]

Configuring Communication 29 MVP-5200i Modero Viewpoint Widescreen Touch Panel 8. W ithin the WEP Passphrase keyboard (FIG. 27), enter a character string or word (such as AMXP anel ) and press Done when f inished.  For e xample, enter th e word AMXP ane l using a 128-bit hex dig it encryption. After pressing Done , the on-screen Current K ey fie[...]

Configuring Communication 30 MVP-5200i Modero Viewpoint Widescreen Touch Panel 12. V erify that the fields within the IP Settings section ha ve been properly configured. Refer to Step 1: Configur e the Device’ s W ir eless IP Settings section on page 21 for detailed information. 13. Press the Back b u tton to na vigate to the Protected Setup page[...]

Configuring Communication 31 MVP-5200i Modero Viewpoint Widescreen Touch Panel Step 3: Choose a Master Connection Mode The MVP-5200i requires a decision on the type of connection to be made between it and the Master . T o establish a Master connection: 1. From the Pr otected Setup page, select System Settings . 2. Select T ype to toggle between the[...]

Configuring Communication 32 MVP-5200i Modero Viewpoint Widescreen Touch Panel Touch panel setup T o prepare the MVP-5200i for Ethernet for USB communication: 1. T urn on the MVP-5200i and wait for the de vice to finish booting up. 2. Insert the mini-USB end of the USB Programmi ng Cable into the mini-USB port on the de vice. Insert the other end i[...]

Configuring Communication 33 MVP-5200i Modero Viewpoint Widescreen Touch Panel 6. In the next box (FIG. 33), make sure to:  Select Sear ch for the best driver in these locations  Select Include this location in the searc h  Click on Br owse  Select the folder that contains the 'linux.inf' file 7. Click on Next . 8. The W indow[...]

Configuring Communication 34 MVP-5200i Modero Viewpoint Widescreen Touch Panel 9. Once the system finds the driv er, it displays its choice (FIG. 35). Click Finish to complete the driv er installation. When an IP address is assigned to the usb0 interface on the de vice, W i ndo ws XP will make an attempt to assign an IP address to the corresponding[...]

Configuring Communication 35 MVP-5200i Modero Viewpoint Widescreen Touch Panel 5. In the new windo w:  Select Use the following IP Addr ess .  Unde r IP addr ess , provide an IP address (e nsure that it is in the same subne t as the IP address giv en to the usb0 interface on the MVP-5200i).  Under Subnet mask , set the suitable subnet mask[...]

Configuring Communication 36 MVP-5200i Modero Viewpoint Widescreen Touch Panel 3. Click the Communications Settings button to open the Com munications Settings dialog (FIG. 38). 4. Click the NetLinx Master radio button in the Platform Selection section. 5. Click the V ir tual NetLinx Master radio button in the T ransport Connection Option section. [...]

Configuring Communication 37 MVP-5200i Modero Viewpoint Widescreen Touch Panel Ethernet 1. When using W ireless Ethernet, press the listed Mode to toggle th rough the av ailable connection modes: 2. Select the Master P ort Number to ope n the keypad and change this v alue. The default setting for the port is 1319 . 3. Set the Master Port and select[...]

Configuring Communication 38 MVP-5200i Modero Viewpoint Widescreen Touch Panel Master Connection to a Virtua l Master via Ethernet Before beginning: 1. V erify that the panel has been configured to communicate with the W ireless Access Point and confirm that the signal strength quality bargraph is On . 2. In NetLinx Studio, select Settings > Mas[...]

Configuring Communication 39 MVP-5200i Modero Viewpoint Widescreen Touch Panel 5. Click on the Virtual NetLinx Master radio box from the T ransport Connection Option section to indicate wanting to conf ig ure the PC to communicate with a panel. Everything else, such as the Authentication, is greyed out because the procedure is not being made throug[...]

Configuring Communication 40 MVP-5200i Modero Viewpoint Widescreen Touch Panel 13. Select Protected Setup > System Settings (located on the lo wer-left) to open th e System Settings page (FIG. 43). 14. Press the blue T ype field ( from the Master Connection section ) until the choice cycles to the word Ethernet. 15. Press the Mode f ield until t[...]

Configuring Communication 41 MVP-5200i Modero Viewpoint Widescreen Touch Panel Using G4 Web Control to Interact with a G4 Panel The G4 W eb Control feature allows you to use a PC to intera ct with a G4-enabled panel via the W eb . This feature works in tandem with the ne w browse r-capable NetLinx Security firmware update ( b uild 300 or higher ). [...]

Configuring Communication 42 MVP-5200i Modero Viewpoint Widescreen Touch Panel 8. From the We b N a m e keyboard, enter a unique alpha-numeric string to identify this panel. This information is used by the NetLinx Security W eb Server to display on -screen links to the panel. The on-screen links use the IP Address of the pane l and not the name for[...]

Configuring Communication 43 MVP-5200i Modero Viewpoint Widescreen Touch Panel Using the NetLinx Master to control the G4 panel Refer to the particular NetLinx Master’ s instruction manual for detailed information on how to do w nload the latest firmw are from www .amx.com . This firmware build enables SSL certif icate identification and encrypti[...]

Configuring Communication 44 MVP-5200i Modero Viewpoint Widescreen Touch Panel 5. Click on the G4 panel name link associated with the target panel. A secondary web bro wser window appears on the screen (FIG. 47). 6. Click Ye s from the Security Alert popup window to agree to the installation of the G4 W ebControl application on your computer . This[...]

Configuring Communication 45 MVP-5200i Modero Viewpoint Widescreen Touch Panel 9. Enter the W eb Control session password into the Session P asswor d field (FIG. 48). This passwor d was pr eviously entered into the W eb Contr ol P asswor d field within the G4 W eb Contr ol page on the panel. 10. Click OK to send the password to the panel and begin [...]

Configuring Communication 46 MVP-5200i Modero Viewpoint Widescreen Touch Panel[...]

Setup Pages 47 MVP-5200i Modero Viewpoint Widescreen Touch Panel Setup Pages The MVP-5200i features on-board Setup pages. Use the options in the Setup pages to access panel information and make various conf iguration cha nges. T o access the Setup pages, press the center button of the navigation wheel and hold for 3 to 5 seconds (FIG. 49). Setup Pa[...]

Setup Pages 48 MVP-5200i Modero Viewpoint Widescreen Touch Panel Setup Page (Cont.) Connection Status: Displays whether the panel is has exte rnal communication, as well as the encryption status of the Master , the connection type ( Ethernet or USB ), and to which System the panel is connected. • Until a connection is establis hed, the message di[...]

Setup Pages 49 MVP-5200i Modero Viewpoint Widescreen Touch Panel Navigation Buttons The follo win g Na vigation buttons (FIG. 51) appear on the left side of the Setup page: Protected Setup Pages Information on the Protected Setup pages is available on page 59. FIG. 51 Setup Page Nav igation Buttons Press to access the Protected Setup pages. Press t[...]

Setup Pages 50 MVP-5200i Modero Viewpoint Widescreen Touch Panel Information Button The Information b utton allows access of both the Pr oject Information page, w hich contains data on the TPDesign4 file being used with the MVP-5200i, and the P anel Information page, which contains detailed information on the panel itself. T o access these pages: 1[...]

Setup Pages 51 MVP-5200i Modero Viewpoint Widescreen Touch Panel Project Information Page (Cont.) Sales Order: Displays the sales order information. Purchase Order: Displays the purchase order information. AMX IR 38K Assigned Port: Displays the AMX 38 kHz IR channel port used by the IR Emitter on the panel. • This information is specified in TPD4[...]

Setup Pages 52 MVP-5200i Modero Viewpoint Widescreen Touch Panel Panel Information Page The Panel Information page provides detailed panel information (FIG. 53). Features on this page include: FIG. 53 Panel Information page Panel Information Page Back: Saves all changes and returns to the previous page. Connection Status icon: The icon in the upper[...]

Setup Pages 53 MVP-5200i Modero Viewpoint Widescreen Touch Panel Time & Date Settings Page The options on the T ime & Date Settings page (FIG. 54) allows setting and adjusting o f time and date information on the NetLinx Master . If the time and/o r date on the Master is modified, all connected devices will be u pdated to reflect the ne w i[...]

Setup Pages 54 MVP-5200i Modero Viewpoint Widescreen Touch Panel Audio Settings Page The Audio Settings page allows adjustment of v olume lev els and pa nel sounds settings (FIG. 55). Features on these pages include: FIG. 55 Audio Settings pages Audio Settings Page Back: Saves all changes and returns to the previous page. Connection Status icon: Th[...]

Setup Pages 55 MVP-5200i Modero Viewpoint Widescreen Touch Panel WAV files - Supported sam ple rates The following sample rates for W A V files are supported by MVP-5200i panels: Audio Settings Page (Cont.) Analog Line In Level: Adjusts the volume level of any analog signal coming into the device: • Use the Up/Down buttons to adjust the in put le[...]

Setup Pages 56 MVP-5200i Modero Viewpoint Widescreen Touch Panel Battery Settings Page The options on the Battery Settings page allow setting of po w er warning preferences and battery status information, and adjustment of the display times for battery warnings (FIG. 56). Features on this page include: FIG. 56 Battery page Battery Page Back: Saves [...]

Setup Pages 57 MVP-5200i Modero Viewpoint Widescreen Touch Panel Battery Page (Cont.) Battery Power Brightness Limit: The DISABLE/DISABLED button acts as a power save feature with two options: • Disable - Clicking on this button deactivate s this power save feature. The panel will use the Panel Brightness level. • Disabled - Clicking on this bu[...]

Setup Pages 58 MVP-5200i Modero Viewpoint Widescreen Touch Panel[...]

Protected Setup Pages 59 MVP-5200i Modero Viewpoint Widescreen Touch Panel Protected Setup Pages The Pr otected Setup page (FIG. 57) provides secured access to advanced panel configuration options, including communication and security settings. The Pr otected Setu p page is accessed through the Setup page (please refer to the Setup P ag es sec tion[...]

Protected Setup Pages 60 MVP-5200i Modero Viewpoint Widescreen Touch Panel T o rebo ot the panel: 1. Access the Pr otected Setup page. 2. Press the Reboot b utton. 3. W ait until the panel completes its reboot. 4. Log back into the Protected Setup page, if necessary . T o shut down the panel: 1. Access the Pr otected Setup page. 2. Press the Shutdo[...]

Protected Setup Pages 61 MVP-5200i Modero Viewpoint Widescreen Touch Panel Protected Setup Navigation Buttons The Protected Setup Navigation Buttons (FIG. 59) appea r on the left edge of the Protected Setup page. FIG. 59 Protected Setup Navigation Buttons Press to access the G4 Web Control p age, which enables and disab les remote Press to access t[...]

Protected Setup Pages 62 MVP-5200i Modero Viewpoint Widescreen Touch Panel System Settings Page The System Settings page (FIG. 60) d isplays se ts the NetLinx Master’ s communication settings. The elements of this page include: FIG. 60 System Settings page System Settings Page Elements Back: Saves all changes and returns to the previous page. Con[...]

Protected Setup Pages 63 MVP-5200i Modero Viewpoint Widescreen Touch Panel Refer to the Step 3: Choose a Master Connection Mode section on p age 31 for more detailed information on using the System Settings page. System Setting Page Elements (Cont.) Mode Cycles between the connection modes : URL, Listen, NDP(UDP ,) URL(UDP), and Auto. (Ethernet Onl[...]

Protected Setup Pages 64 MVP-5200i Modero Viewpoint Widescreen Touch Panel Wireless Settings Page Use the options on the W ir eless Settings page (FIG. 61) to configure communication settings for the wireless CF card (802.11b/g), an d read the device number assigned to the panel. Features on this page include: FIG. 61 Wireless Settings page (reads [...]

Protected Setup Pages 65 MVP-5200i Modero Viewpoint Widescreen Touch Panel Wireless Settings Page (Cont.) Access Point MAC Address: This unique address identifies the Wirele ss Access Point (WAP) used by this panel for wireless communication (read-only). • Site Survey button: Launches the Wireless Site Survey page. The options o n this page allow[...]

Protected Setup Pages 66 MVP-5200i Modero Viewpoint Widescreen Touch Panel Wireless Settings Page (Cont.) Wireless Security (Cont.): EAP-TLS This button opens the EAP-TLS Settings page (FIG . 72 on page 81). “EAP-TLS” security is designed for wireless enviro nments where securely transmitting data over a wireless network by adding an additional[...]

Protected Setup Pages 67 MVP-5200i Modero Viewpoint Widescreen Touch Panel Wireless Security The options on the W ir eless Security section (FIG. 62) include the wireless security methods supported by the NXA-WC80211GCF W i-Fi card. Thes e security methods incorporate WP A , WP A2 , and EAP technology , some of which re quire the upload of unique c[...]

Protected Setup Pages 68 MVP-5200i Modero Viewpoint Widescreen Touch Panel Open (Clear Text ) Settings Press the Open (Clear T ext) button to open the O pen (Clear T ext) Settings page (FIG. 63). Open security does not utilize any encryption methodology , but requires an SSID (alpha-numeric) entry . This entry must match the Network Name (SSID) en [...]

Protected Setup Pages 69 MVP-5200i Modero Viewpoint Widescreen Touch Panel Static WEP Settings Press the Static WEP b utton to open the Static WEP Setting s page (FIG. 64). Static WEP security requires that both a target W AP be identif ied and an encryption method be implemented prior to establishing communication. In addition to providing both Op[...]

Protected Setup Pages 70 MVP-5200i Modero Viewpoint Widescreen Touch Panel Refer to the Conf iguring W ir eless Network Access section on page 21 and the Using the Site Surve y tool section on page 23 for further details on these security options. Static WEP Settings (Cont.) Generate (Passphrase): This button displays an on-screen keyboar d which a[...]

Protected Setup Pages 71 MVP-5200i Modero Viewpoint Widescreen Touch Panel WPA-PSK Settings Press the WP A-PSK button to opens the WP A-PSK dialog (FIG. 65). WP A-PSK security is designe d for en vironments where using W P A or WP A2 is desirable, but an 802.1x authentication server is not av ailable. PSK connecti ons are more secure than WEP and a[...]

Protected Setup Pages 72 MVP-5200i Modero Viewpoint Widescreen Touch Panel  Refer to the Configuring W ir eless Network Access section on page 21 for details on these security options.  Refer to the Using the Site Survey tool section on page 23 for more information on using this tool. EAP Security & Server Certificates - Overview The foll[...]

Protected Setup Pages 73 MVP-5200i Modero Viewpoint Widescreen Touch Panel EAP-LEAP Setting s Press the EAP-LE AP button to open the EAP-LEAP Settings page (FIG. 67). EAP (Extensible Authentication Protocol) is an Enterprise authentication protocol that can be used in both wired and wireless network en vironments. EAP requires the use of an 802.1x [...]

Protected Setup Pages 74 MVP-5200i Modero Viewpoint Widescreen Touch Panel  Refer to the EAP Authentication section on page 166 for further details on these security options.  Refer to FIG. 68 for an example of how a typical EAP-LEAP system con f iguration page should appear . EAP-LEAP Settings SSID (Service Set Identifier): Opens an on-scree[...]

Protected Setup Pages 75 MVP-5200i Modero Viewpoint Widescreen Touch Panel EAP-FAST Settin gs Press the EAP-F AST button to open the EAP-F AST Settings dialog (FIG. 69). EAP-F AST (Fle xible Authentication via Secu re T unneling) security was designed for wireless en vironments where security and ease of setup are e qually desirable. EAP-F AST u se[...]

Protected Setup Pages 76 MVP-5200i Modero Viewpoint Widescreen Touch Panel Refer to the EAP A uthentication section on page 166 and the Using the Site Surve y too l section on page 23 for further details on these security options. EAP-FAST Settings (Cont.) Anonymous Identity: Opens an on-screen keyboard to enter an IT provided alphanumeric string w[...]

Protected Setup Pages 77 MVP-5200i Modero Viewpoint Widescreen Touch Panel EAP-PEAP Settings Press the EAP-PE AP button to open the EAP-PEAP Settings page (FIG. 70). PEAP (Protected Extensib le Authentication Protoc ol) was dev eloped as a way to securely transmit authentication information, such as passwords, ov e r a wireless network en vironment[...]

Protected Setup Pages 78 MVP-5200i Modero Viewpoint Widescreen Touch Panel EAP-PEAP security is designed for wireless en vironmen ts where it is necessary to transmit data securely ov e r a wireless network. Refer to the EAP A uthentication section on page 166 and the Using the Site Surve y too l section on page 23 for further details on these secu[...]

Protected Setup Pages 79 MVP-5200i Modero Viewpoint Widescreen Touch Panel EAP-TTLS Setting s Press the EAP-TT LS b utton to opens the EAP-TTLS Settings page (FIG. 71). TTLS (EAP T unneled Transport Layer Security) is an authentication method that does not use a c lient certificate to authenticate the panel. Howe ver . this method is more secure th[...]

Protected Setup Pages 80 MVP-5200i Modero Viewpoint Widescreen Touch Panel Refer to the EAP A uthentication section on page 166 and the Using the Site Surve y too l section on page 23 for further details on these security options. EAP-TTLS Settings (Cont.) Identity: Opens an on-screen keyboard. Enter an EAP Identity string (used by the panel to ide[...]

Protected Setup Pages 81 MVP-5200i Modero Viewpoint Widescreen Touch Panel EAP-TLS Settings Press the EAP-TL S button to open the EAP-TLS Settings page (FIG. 72). TLS (T ransport Layer Security) was the original st andard wireless LAN EAP authentication protocol. TLS requires additional work during the deployment phase, b ut provides additional sec[...]

Protected Setup Pages 82 MVP-5200i Modero Viewpoint Widescreen Touch Panel  Refer to the EAP Authentication section on page 166 for further details on these security options.  Refer to the Using the Site Survey tool section on page 23 for more information on using this feature. EAP-TLS Settings (Cont.) Certificate Authority: When pressed, the[...]

Protected Setup Pages 83 MVP-5200i Modero Viewpoint Widescreen Touch Panel Client certificate configuration A client certificate can be conf igured by an IT depa rtment in sev eral ways. The client certificate and priv ate key can both be incorporated into on e file or sp lit into two separate f iles. In addition, the file format used by these fil [...]

Protected Setup Pages 84 MVP-5200i Modero Viewpoint Widescreen Touch Panel Calibration Page The Calibration page (FIG. 73) allo ws you to calibra te the touch panel for accurate button selection. 1. Press and hold the cen ter button on the navigation wheel for 6 seconds to access the Calibration page (see FIG. 57). 2. Press the crosshairs in turn. [...]

Protected Setup Pages 85 MVP-5200i Modero Viewpoint Widescreen Touch Panel G4 Web Control Settings Page An on-board VNC (V irtual Network Computing) serv er allows the panel to connect to any remote PC running a VNC client. Once connected, the client can vie w and control the panel remotely . The options on this page allow you to e nable/disable G4[...]

Protected Setup Pages 86 MVP-5200i Modero Viewpoint Widescreen Touch Panel Refer to the Using G4 Web Contro l to Interact wit h a G4 Panel section on page 41 for instructions on using the G4 Web Control page with the web-based NetLinx Security application.[...]

Protected Setup Pages 87 MVP-5200i Modero Viewpoint Widescreen Touch Panel Other Settings Press the Other Settings b utton to display the two settings options for Cache and Pas sword . Press one of the options within three seconds, or the two options buttons will slide back behind the Other Settings button. Cache Settings Page The options on the Ca[...]

Protected Setup Pages 88 MVP-5200i Modero Viewpoint Widescreen Touch Panel Password Settings Page The options on the P assword Settings page (FIG. 76) allo w assignment of passwords required for users to access the Protected Setup page, and to release the device from a MVP-WCS-52 Charging Station. Features on this page include: T o change a previou[...]

Protected Setup Pages 89 MVP-5200i Modero Viewpoint Widescreen Touch Panel The User Access section allows the Administrator to control access of all individuals using or attempting to use the MVP-5200i. From this section, new users may be gi ven access rights to the de vice; howe ver , they will NO T be given access to the Pr otected Settings page.[...]

Protected Setup Pages 90 MVP-5200i Modero Viewpoint Widescreen Touch Panel Tools Press and hold the T ools button to access the MVP-5200i’ s Panel Logs , Panel Statistics , and Connection Utility buttons (FIG. 77). Each of these b uttons opens a separate page, covered in detail below . Panel Connection Logs Page The P anel Connection Logs page (F[...]

Protected Setup Pages 91 MVP-5200i Modero Viewpoint Widescreen Touch Panel Panel Statisti cs Page The P anel Statistics page (FIG. 79) displays activity between the de vice and the network in proportions of ICSP messages, blink messages, a nd Ethe rnet versus wireless use. FIG. 79 Panel Statistics Page Panel Statistics Page Back: Saves all changes [...]

Protected Setup Pages 92 MVP-5200i Modero Viewpoint Widescreen Touch Panel Connection U tility Page The Connection Utility page (FIG. 80) d isplays the current wired and wireless connection information, including the latest link quality and signal strength information. FIG. 80 Connection Utility Page Connection Utility Page Connection Information: [...]

Upgrading Firmware 93 MVP-5200i Modero Viewpoint Widescreen Touch Panel Upgrading Firmware For the purpose of panel downloads, t h e MVP-5200i’ s download procedure is not compatible with other AMX panel de vices. This is due to the unique configuration of the de vice. The first major change from other AMX de vices is that the MVP-5200i uses dyna[...]

Upgrading Firmware 94 MVP-5200i Modero Viewpoint Widescreen Touch Panel 4. T oggle the blue Ty p e field in the Master Connection section until the choice cycles to USB . 5. Press the Back b utton on the touch panel to return to the Pr otected Setup page. 6. Press the Reboot button to both sav e any changes and restart the panel. Remember that the [...]

Upgrading Firmware 95 MVP-5200i Modero Viewpoint Widescreen Touch Panel 2. Click the Communications Settings b utton to open the Communications Settings dialog (FIG. 82). 3. Click on the NetLinx Master radio button from the Platform Selection section. 4. Click on the Virtual Master radio box from the T ransport Connection Option section to configur[...]

Upgrading Firmware 96 MVP-5200i Modero Viewpoint Widescreen Touch Panel 3. After the Communication V erification dialog windo w verifies acti ve communication between the V irtual Master and the panel, click the OnLine T ree tab in the W orkspace window (FIG. 83) to view the devices on the V irtual System. The default Sy stem value is 1 . 4. Right-[...]

Upgrading Firmware 97 MVP-5200i Modero Viewpoint Widescreen Touch Panel 7. Select T ools > Firmware T ransfers > Send to NetLinx Device from the Main menu to open the Send to NetLinx Device dia log ( B in FIG. 84). V erify that the panel’ s System and Device number va lues match those va lues listed within the System folder in the OnLine T [...]

Upgrading Firmware 98 MVP-5200i Modero Viewpoint Widescreen Touch Panel A Special Note for Network Interface Connections Due to any USB connection to your PC being ma de through a Network Interface Connection (NIC), W indows will automatically make an y new NIC connec tion the Primary connection. If this happens, the USB address of 12.0.0.x will sh[...]

Upgrading Firmware 99 MVP-5200i Modero Viewpoint Widescreen Touch Panel 3. From the Advanced menu, select Advanced Settings... to open the Advanced Settings windo w (FIG. 86 ). 4. Under the Adapters And Bindings tab, the user needs to make sure the Local Area Connection is not at the top of the Connec tions list. If it is at the top of the list (FI[...]

Upgrading Firmware 100 MVP-5200i Modero Viewpoint Widescreen Touch Panel 6. When f inished, click OK to close the Advanced Settings windo w and sav e all change s. FIG. 88 Bindings for Local area list detail[...]

Programming 101 MVP-5200i Modero Viewpoint Widescreen Touch Panel Programming Overview Y ou can program the MV P-5200i, using the commands in this section, to perform a wide variety of operations using Send_Commands and variable text commands. A device must f irst be defined in the NetLinx pr ogramming language with values f or the Device: Por t : [...]

Programming 102 MVP-5200i Modero Viewpoint Widescreen Touch Panel Page Commands (Cont. ) @DPG Delete a specific popup page from specified popup group if it exists. Syntax: "'@DPG-<popup page name>;<popup group name>'" Va r i a b l e : popup page name = 1 - 50 ASCII characters. Name of the popup page. popup group name[...]

Programming 103 MVP-5200i Modero Viewpoint Widescreen Touch Panel Page Commands (Cont.) @PP A Close all popups on a specified page. If the page name is empty , the current page is used. Same as the ’Clear Page’ command in TPDesign4. Syntax: "'@PPA-<page name>'" Va r i a b l e : page name = 1 - 50 ASCII characters. Name[...]

Programming 104 MVP-5200i Modero Viewpoint Widescreen Touch Panel Page Commands (Cont. ) @PPM Set the modality of a specific popup page to Modal or NonModal. A Modal popup page, when active, only allows you to use the buttons and features on that popup page. All other buttons on the panel page are inactivated. Syntax: "'@PPM-<popup pag[...]

Programming 105 MVP-5200i Modero Viewpoint Widescreen Touch Panel Page Commands (Cont.) @PSE Set the show effect for the specified popup page to the named show effect. Syntax: "'@PSE-<popup page name>;<show effect name>'" Va r i a b l e : popup page name = 1 - 50 ASCII characters. Name of the page the popup is displa[...]

Programming 106 MVP-5200i Modero Viewpoint Widescreen Touch Panel Page Commands (Cont. ) PPOF Deactivate a specific popup page on either a specified page or the current page. If the page name is empty , the curr ent page is used (see example 2). If the popup page is part of a group, the whole group is deactivat ed. This command works in the same wa[...]

Programming 107 MVP-5200i Modero Viewpoint Widescreen Touch Panel Programming Numbers The follo win g information provides the program ming numbers for colors, fonts, and borders. Colors can be used to set the colors on buttons, sliders, and pages. The lowest color number represents the lightest color-specif ic display; the highest number represent[...]

Programming 108 MVP-5200i Modero Viewpoint Widescreen Touch Panel RGB Values for all 88 Basic Colors (Cont.) Index No . Name Red Green Blue 36 V ery Light Cyan 0 255 255 37 Light Cyan 0 223 223 38 Cyan 0 191 191 39 Medium C yan 0 159 159 40 Dark Cyan 0 127 127 41 V ery Dark Cyan 0 95 95 42 V ery Light Aqua 0 128 255 43 Light Aqua 0 1 12 223 44 Aqua[...]

Programming 109 MVP-5200i Modero Viewpoint Widescreen Touch Panel Font styles and ID numbers Font styles can be used to program the text font s on buttons, sliders, and pages. The follo wing chart shows the def au lt font type and their respecti ve ID numbers generated by TPDesign4. RGB Values for all 88 Basic Colors (Cont.) Index No . Name Red Gre[...]

Programming 110 MVP-5200i Modero Viewpoint Widescreen Touch Panel Border styles and Programmi ng numbers Border styles can be used to program bor ders on bu ttons, sliders, and popup pages. The TPDesign4 T ouch Panel Design program has pr e-set border styles that are user-selectable. The following number v alues cannot be used for programming purpo[...]

Programming 111 MVP-5200i Modero Viewpoint Widescreen Touch Panel TPD4 Border Styles by Name (Cont.) No. Border styles No. Border styles 53 Diamond 185 97 Menu Bo ttom Rounded 185 54 Diamond 195 98 Menu Bo ttom Rounded 195 55 Double Bevel -L 99 Menu T op Rounded 15 56 Double Bevel -M 100 Menu T op Rounded 25 57 Double Bevel -S 101 Menu T op Rounded[...]

Programming 112 MVP-5200i Modero Viewpoint Widescreen Touch Panel TPD4 Border Styles by Name (Cont.) No. Border styles No. Border styles 141 Menu Left Rounded 55 149 Menu Left Rounded 135 142 Menu Left Rounded 65 150 Menu Left Rounded 145 143 Menu Left Rounded 75 151 Menu Left Rounded 155 144 Menu Left Rounded 85 152 Menu Left Rounded 165 145 Menu [...]

Programming 113 MVP-5200i Modero Viewpoint Widescreen Touch Panel "^" Button Commands These Button Commands are used in NetLinx Studio and are case insensiti ve. All commands that begin with " ^ " hav e the capability of assigning a variable text address range and button state range. A de vice must first be defined in the NetLin[...]

Programming 114 MVP-5200i Modero Viewpoint Widescreen Touch Panel "^" Button Commands (Cont .) ^B A U Append unicode text. Same format as ^UNI. Syntax: "'^BAU-<vt addr range>,<button states range>,<unicode text>'" Va r i a b l e : variable text address range = 1 - 4000. button states range = 1 - 256 f[...]

Programming 115 MVP-5200i Modero Viewpoint Widescreen Touch Panel "^" Button Commands (Cont.) ^BCT Set the text color to the specified color . Only if the specified text color is not the same as the curren t color . Note : Color can be assigned by color name (without spaces), number or R,G ,B value (RRGGBB or RRGGBBAA). Syntax: "&apo[...]

Programming 116 MVP-5200i Modero Viewpoint Widescreen Touch Panel "^" Button Commands (Cont .) ^BIM Set the input mask for the specified address. Syntax: "'^BIM-<vt addr range>,<input mask>'" Va r i a b l e : variable text address range = 1 - 4000. input mask = Refer to the T ext Area Input Masking table on[...]

Programming 117 MVP-5200i Modero Viewpoint Widescreen Touch Panel "^" Button Commands (Cont.) ^BMC Button copy command. Copy attributes of the source button to all the destination buttons. Note that the source is a single button state. Each state must be copied as a separate command. The <codes> section represents what attributes wi[...]

Programming 118 MVP-5200i Modero Viewpoint Widescreen Touch Panel "^" Button Commands (Cont .) ^BMF Set any/all button parameters by sending embedded codes and data. Syntax: "'^BMF-<vt addr range>,<button states range>,<data>'" Va r i a b l e s : variable text address char array = 1 - 4000. button sta[...]

Programming 119 MVP-5200i Modero Viewpoint Widescreen Touch Panel "^" Button Commands (Cont.) ^BMF (Cont.) For some of these commands and values, refer to the RGB V alues for all 88 Basic Colors table on page 107. ’%CF<on fill color >’ = Set Fill Color. ’%CB<on border color>’ = Set Border Color. ’%CT<on text color[...]

Programming 120 MVP-5200i Modero Viewpoint Widescreen Touch Panel "^" Button Commands (Cont .) ^BMI Set the button mask image. Mask image is used to crop a borderless button to a non-square shap e. This is typically used with a bitmap. Syntax: "'^BMI-<vt addr range>,<button states range>,<mask image>'"[...]

Programming 121 MVP-5200i Modero Viewpoint Widescreen Touch Panel "^" Button Commands (Cont.) ^BNN Set the T akeNote network name for the specified Addresses. Syntax: "'^BNN-<vt addr range>,<network name>'" Va r i a b l e : variable text address range = 1 - 4000. network name = Use a valid IP Address. Examp[...]

Programming 122 MVP-5200i Modero Viewpoint Widescreen Touch Panel "^" Button Commands (Cont .) ^BOR Set a border to a specific border style associated with a border value for those buttons with a defined address range. Refer to the Border Styles and Programming Numbers table on page 1 10 for more information. Syntax: "'^BOR-<[...]

Programming 123 MVP-5200i Modero Viewpoint Widescreen Touch Panel "^" Button Commands (Cont.) ^BRD Set the border of a button state/ states. Only if the specified border is not the same as the current border . The border names are available through the TPDesign4 border -name drop-down list. Syntax: "'^BRD-<vt addr range>,&[...]

Programming 124 MVP-5200i Modero Viewpoint Widescreen Touch Panel "^" Button Commands (Cont .) ^BVL Log-On/Log-Off the computer control connection. Syntax: "'^BVL-<vt addr range>,<connection>'" Va r i a b l e : variable text address range = 1 - 4000. connection = 0 (Log-Off connection) and 1 (Log-On connect[...]

Programming 125 MVP-5200i Modero Viewpoint Widescreen Touch Panel "^" Button Commands (Cont.) ^CPF Clear all page flip s from a button. Syntax: "'^CPF-<vt addr range>'" Va r i a b l e : variable text address range = 1 - 4000. Example: SEND_COMMAND Panel,"'^CPF-500'" Clears all page flips from [...]

Programming 126 MVP-5200i Modero Viewpoint Widescreen Touch Panel "^" Button Commands (Cont .) ^FON Set a font to a specific Font ID value for those buttons with a defined address range. Font ID numbers are generated by th e TPDesign4 programmers report. Syntax: "'^FON-<vt addr range>,<button states range>,<font v[...]

Programming 127 MVP-5200i Modero Viewpoint Widescreen Touch Panel "^" Button Commands (Cont.) ^GLH Change the bargraph upper limit. Syntax: "'^GLH-<vt addr range>,<bargraph hi>'" Va r i a b l e : variable text address range = 1 - 4000. bargraph limit range = 1 - 65535 ( bargr aph upper limit range ). Exampl[...]

Programming 128 MVP-5200i Modero Viewpoint Widescreen Touch Panel "^" Button Commands (Cont .) ^GSN Change the bargraph slider name or joystick cursor name. Slider names and cursor names can be f ound in the TP Design4 slider name and cursor drop-down list. Syntax: "'^GSN-<vt addr range>,<bargraph slider name>'&[...]

Programming 129 MVP-5200i Modero Viewpoint Widescreen Touch Panel "^" Button Commands (Cont.) ^JSB Set bitmap/ picture alignment using a numeric keypad layout for those buttons with a defined address range. The alignment of 0 is followed by ',<left>,<top> '. The left and top coordinates are relative to the upper left[...]

Programming 130 MVP-5200i Modero Viewpoint Widescreen Touch Panel "^" Button Commands (Cont .) ^JST Set text alignment using a numeric keypad layout for those buttons with a defined address range. The alignment of 0 is followed by ',<left>,<top> '. The left and top coordinates are relative to the upper left corner of[...]

Programming 131 MVP-5200i Modero Viewpoint Widescreen Touch Panel "^" Button Commands (Cont.) ^TEC Set the text effect color for the specified addresses/states to the specified color . The T ext Effect is specified by name and c an be found in TPD4. Y ou can also assign the color by name or RGB va lue (RRGGBB or RRGGBBAA). Syntax: "&[...]

Programming 132 MVP-5200i Modero Viewpoint Widescreen Touch Panel Miscellaneous MVP Stri ngs back to the Master The following tw o strings are sent by the MVP panel back to the communicating Master: MVP Panel Loc k Passcode comm ands These commands are used to maintain a passcode list. W ith the MV OP-5200i, a password must be entered to remove the[...]

Programming 133 MVP-5200i Modero Viewpoint Widescreen Touch Panel Text Effects Names The following is a listing of text ef fects nam es associated with the ^TEF command on page 131. MVP Panel Lock Passcode Commands ( Cont.) ^LPR Remove a given user from the User Access Passwords li st on the Password Setup page. Syntax: "'^LPR-<user>[...]

Programming 134 MVP-5200i Modero Viewpoint Widescreen Touch Panel Button Query Commands Button Query commands reply back with a custom ev ent. There will be one custom event for each button/state combination. Each query is assigned a unique custom e vent type. The following example is for deb ug purposes only: NetLinx Example: CUSTOM_EVENT[device, [...]

Programming 135 MVP-5200i Modero Viewpoint Widescreen Touch Panel All custom ev ents hav e the follo wing 7 fields: These fields are populated dif ferently for each query command. The text length (String Encode) field is not used in any command. Custom Event Fields Field Description Uint Flag 0 means text is a standard string, 1 means Unicode encod[...]

Programming 136 MVP-5200i Modero Viewpoint Widescreen Touch Panel Button Query Commands (Cont.) ?BCF Get the current fill color . Syntax: "'?BCF-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000. button states range = 1 - 256 for multi-state buttons (0 = All states, for G[...]

Programming 137 MVP-5200i Modero Viewpoint Widescreen Touch Panel Button Query Commands (Cont.) ?BMP Get the current bitmap name. Syntax: "'?BMP-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000. button states range = 1 - 256 for multi-state buttons (0 = All states, for G[...]

Programming 138 MVP-5200i Modero Viewpoint Widescreen Touch Panel Button Query Commands (Cont.) ?BRD Get the current border name. Syntax: "'?BRD-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000. button states range = 1 - 256 for multi-state buttons (0 = All states, for G[...]

Programming 139 MVP-5200i Modero Viewpoint Widescreen Touch Panel Button Query Commands (Cont.) ?FON Get the current font index. Syntax: "'?FON-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000. button states range = 1 - 256 for multi-state buttons (0 = All states, for Ge[...]

Programming 140 MVP-5200i Modero Viewpoint Widescreen Touch Panel Button Query Commands (Cont.) ?JSB Get the current bitmap justification. Syntax: "'?JSB-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000. button states range = 1 - 256 for multi-state buttons (0 = All stat[...]

Programming 141 MVP-5200i Modero Viewpoint Widescreen Touch Panel Button Query Commands (Cont.) ?JST Get the current text justification. Syntax: "'?JST-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000. button states range = 1 - 256 for multi-state buttons (0 = All states[...]

Programming 142 MVP-5200i Modero Viewpoint Widescreen Touch Panel Button Query Commands (Cont.) ?TEF Get the current text effect name. Syntax: "'?TEF-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000. button states range = 1 - 256 for multi-state buttons (0 = All states, [...]

Programming 143 MVP-5200i Modero Viewpoint Widescreen Touch Panel Panel Runtime Operations Serial Commands are used in the AxcessX T erminal Emulator mode. These commands are case insensitiv e. Panel Runtime Op eration Commands ABEEP Output a single beep even if beep is Off. Syntax: "'ABEEP'" Example: SEND COMMAND Panel,"&a[...]

Programming 144 MVP-5200i Modero Viewpoint Widescreen Touch Panel Panel Runtime Operatio n Commands (Cont.) @AKP Pop up the keypad icon and initialize the text string to that specified. Keypad string is set to null on power up and is stored until power is lost. The Pro mpt T ext is optional. Syntax: "'@AKP-<initial text>;<prompt [...]

Programming 145 MVP-5200i Modero Viewpoint Widescreen Touch Panel Panel Runtime Operatio n Commands (Cont.) @EKP Extend the Keypad. Pops up the keypad icon and initializes the text string to that specified. The Prompt T ext is optional. Syntax: "'@EKP-<initial text>;<prompt text>'" Va r i a b l e s : initial text = 1[...]

Programming 146 MVP-5200i Modero Viewpoint Widescreen Touch Panel Panel Runtime Operatio n Commands (Cont.) @SOU Play a sound file. Syntax: "'@SOU-<sound name>'" Va r i a b l e s : sound name = Name of the sound file. Supported sound file formats are: WAV & MP3. Example: SEND COMMAND Panel,"'@SOU-Music.wav&ap[...]

Programming 147 MVP-5200i Modero Viewpoint Widescreen Touch Panel Input Commands These Send Commands are case insensitive. Input Command s ^CAL Put panel in calibration mode. Syntax: "'^CAL'" Example: SEND COMMAND Panel,"'^CAL'" Puts the panel in calibration mode. ^KPS Set the keyboard pas sth ru . Syntax: &q[...]

Programming 148 MVP-5200i Modero Viewpoint Widescreen Touch Panel Embedded codes The following is a list of G4 compatible embedd ed codes: Embedded Codes Decimal numbers Hexidecimal values Vir tual keystrok e 8 ($08) Backspace 13 ($0D) Enter 27 ($1B) ESC 128 ($80) CTRL key down 129 ($81) AL T key down 130 ($82) Shift key down 131 ($83) F1 132 ($84)[...]

Programming 149 MVP-5200i Modero Viewpoint Widescreen Touch Panel Panel Setup Commands These commands are case insen siti ve. Panel Setup Commands ^MUT Set the panel mute state. Syntax: "'^MUT-<mute state>'" Va r i a b l e : mute state= 0 = Mute Off and 1 = Mute On. Example: SEND_COMMAND Panel,"'^MUT-1'&apos[...]

Programming 150 MVP-5200i Modero Viewpoint Widescreen Touch Panel Dynamic Image Commands The following is a listing and descriptions of Dynamic Image Com mands. Dynamic Image Commands ^BBR Set the bitmap of a button to use a par tic ul ar resource. Syntax: "'^BBR-<vt addr range>,<button states range>,<resource name>&apos[...]

Programming 151 MVP-5200i Modero Viewpoint Widescreen Touch Panel Dynamic Image Commands (Cont.) ^RAF Add new resources. Adds any and all resource paramete rs by sending embedded codes and data. Syntax: "'^RAF-<resource name>,<data>'" Va r i a b l e : resource name = 1 - 50 ASCII characters. data = Refers to the embe[...]

Programming 152 MVP-5200i Modero Viewpoint Widescreen Touch Panel[...]

Battery Life and Replacem ent 153 MVP-5200i Modero Viewpoint Widescreen Touch Panel Battery Life and Replacement Overview The battery po w ering the MVP-5200i is designed for upwards of 300 deep dischar ge re chargings. Regular shallow rechar gings will extensi vely increase expected battery life, a nd the device should be stored in either the T ab[...]

Battery Life and Replacement 154 MVP-5200i Modero Viewpoint Widescreen Touch Panel Battery Replacement The touch panel's battery is intended to last the lif e of the de vice, but in cases where the battery has reached its effecti ve end of life, it ma y be replaced with the MVP-BP-5 2 Battery Pack Kit ( FG5966-20 ). T o replace the battery: 1.[...]

Battery Life and Replacem ent 155 MVP-5200i Modero Viewpoint Widescreen Touch Panel 8. Insert the fi ve screws and replace the screw co vers atop the two upper screws, using the replacement upper scre w covers included in the Battery Pack Kit. 9. Restart the de vice to confirm that the new battery is functioning correctly .[...]

Battery Life and Replacement 156 MVP-5200i Modero Viewpoint Widescreen Touch Panel[...]

Appendix A: Text Formatti ng 157 MVP-5200i Modero Viewpoint Widescreen Touch Panel Appendix A: Text Formatting Text Formatting Codes for Bargraphs/Joysticks T ext formatting codes for bargraphs provide a mechanism to allow a portion of a bar graphs text to be dynamically provided information about the current stat us of the level (multistate and tr[...]

Appendix A: Text Formatting 158 MVP-5200i Modero Viewpoint Widescreen Touch Panel Text Area Input Masking T ext Area Input Masking may be used to limit the allo wed/correct characters that are entered into a text area. For example, in working with a zip code, a user could limit the entry to a max length of only 5 characters; with input masking, thi[...]

Appendix A: Text Formatti ng 159 MVP-5200i Modero Viewpoint Widescreen Touch Panel Refer to the following Send_Commands for more detailed information: Input mask ranges These ranges allow a user to specify the min imum and maximum numeric value for a field. Onl y one range is allow e d per field. Using a range implies a numeric entry ONL Y . An exa[...]

Appendix A: Text Formatting 160 MVP-5200i Modero Viewpoint Widescreen Touch Panel A keyboard entry using normal text entry is straightforward. Ho wever , once an input mask is applied, the behavior of the k eyboard needs to change to accommodate the input mask's requireme nt. When working with masks, any literal characters in the mask w ill be[...]

Appendix A: Text Formatti ng 161 MVP-5200i Modero Viewpoint Widescreen Touch Panel URL Resources A URL can be broken into se veral parts. F or example, with the U RL http://www .amx.com/company-info- home.asp , this URL indicates that the protocol in use is http (HyperT ext T ransport Protocol) a nd that the information resides on a host machine na[...]

Appendix B: Wireless Technology 162 MVP-5200i Modero Viewpoint Widescreen Touch Panel Appendix B: Wireless Technology Overview of Wireless Technology  802.11b/2.4 GHz and 802.11a/5 GHz are the two major WLAN standards and both operate using radio frequency (RF) technology . T ogether the two standards are together called W i-Fi and operate in fr[...]

Appendix B: Wireless Technology 163 MVP-5200i Modero Viewpoint Widescreen Touch Panel Terminology  802.1x  IEEE 802.1x is an IEEE standard that is built on the Internet standard EAP (Extensible Authentication Protocol ). 802.1x is a standard for passing EAP messages ov er either a wired or wirele ss LAN. Additionally , 802.1x is also responsi[...]

Appendix B: Wireless Technology 164 MVP-5200i Modero Viewpoint Widescreen Touch Panel  WEP  Short for W ired Equivalent Pri vac y , WEP is a scheme used to secure wireless networks (W i-Fi). A wireless network broa dcasts messages using radio which are particularly susceptible to hacker a ttacks. WEP was intended to pro vide the confidentiali[...]

Appendix B: Wireless Technology 165 MVP-5200i Modero Viewpoint Widescreen Touch Panel  WP A 2  Also kno w as IEEE 802.11i, this is an amendmen t to the 802.11 standard specifying security mechanisms for wireless networ ks. The 802.11i scheme makes use of the Advanced Encryption Standard (AES) block cipher; WEP and WP A use the RC4 stream ciph[...]

Appendix B: Wireless Technology 166 MVP-5200i Modero Viewpoint Widescreen Touch Panel EAP Authentication EAP (Extensible Authentication Protocol) is an Enterprise authentication protocol that can be used in both a wired and wireless network environment. EAP requires the use of an 802.1x Authentication Server , also kno wn as a RADIUS server . Altho[...]

Appendix B: Wireless Technology 167 MVP-5200i Modero Viewpoint Widescreen Touch Panel EAP communication overview EAP Authentication goes a step beyond just encrypting data transfers, b ut also requires that a set of credentials be validated before the client (panel) is allo w ed to connect to the rest of the network (FIG. 93). Below is a descriptio[...]

Appendix B: Wireless Technology 168 MVP-5200i Modero Viewpoint Widescreen Touch Panel AMX Certificate Upload Utility The Certificate Upload utility gi ves you the ability to compile a list of tar get touch pane ls, select a pre- obtained certificate (uniquely identifying the panel), and then upload that f ile to the selected panel. This application[...]

Appendix B: Wireless Technology 169 MVP-5200i Modero Viewpoint Widescreen Touch Panel Step 2: Confirm the I n stallation of the USB Driver on the PC The first time each AMX touch panel is connected to the PC, it is detected as a ne w hardware de vice and the panel-specific USBLAN dri ver becomes associated with it. Each time thereafter, the panel i[...]

Appendix B: Wireless Technology 170 MVP-5200i Modero Viewpoint Widescreen Touch Panel How to Upload a Certificate File 1. Install the latest AMX USB LAN LINK dri ver onto your computer by installing the latest versions of either TPDesign4 or NetLinx Studio2. Th is USB driv er prepares your computer for proper communication with the MVP-5200i.  R[...]

Appendix C: Troubleshooting 171 MVP-5200i Modero Viewpoint Widescreen Touch Panel Appendix C: Troubleshooting This section describes the solutions to possible ha rdware/f irmware issues that could arise during the common operation of a Modero touch panel. Panel Doesn’t Respond To Touche s Symptom: When calibrating the MVP-5200i, the device either[...]

Appendix C: Troubleshooting 172 MVP-5200i Modero Viewpoint Widescreen Touch Panel MVP-5200i Isn’t Appear ing In The Online Tr ee Tab 1. V erify that the System number is the same on both the NetLinx Project Navigator windo w and the System Settings page on the de vice. 2. V erify the prop er NetLinx Master IP and connection methods entered into t[...]

Appendix C: Troubleshooting 173 MVP-5200i Modero Viewpoint Widescreen Touch Panel If you decide not to pin g for av ailability and the co ntroller is off-line, or you hav e an incorrect TCP/IP address, the program will try for 30- 45 second s to establish a connection. Only One Modero Panel I n My System Shows Up Symptom: I have mor e than one Mod [...]

Appendix C: Troubleshooting 174 MVP-5200i Modero Viewpoint Widescreen Touch Panel[...]

Appendix 175 MVP-5200i Modero Viewpoint Wides creen Touch Panel[...]

4/08 © 2007 AMX. All rights reserved. AMX and the AM X logo are register ed trademarks of AMX. AMX reserves the right to alter specifica tions without notice at any time. It’s Your World - Take Con trol™ 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.222.0193 • 469.624.8000 • 469-624-7153 fax • 800.932.6993 technical support • w[...]