English dropdown-ico

Atmel ATA5283 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Atmel ATA5283, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Atmel ATA5283 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Atmel ATA5283. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Atmel ATA5283 should contain:
- informations concerning technical data of Atmel ATA5283
- name of the manufacturer and a year of construction of the Atmel ATA5283 item
- rules of operation, control and maintenance of the Atmel ATA5283 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Atmel ATA5283 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Atmel ATA5283, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Atmel service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Atmel ATA5283.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Atmel ATA5283 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    Features • W ake-up Function for a Microcontr oller with Preamble Detection • 1m V rms Sensitivity • 1 µA Standby Current • P ower Supply: 2V to 3.8V • Baud Rate: up to 4 kb ps (ASK Modulation) • Operation T emperature: up to 125°C • Withstan ds +175°C • Few External Components Application • Tire Pressure Mo nitoring (TPM) 1. D[...]

  • Page 2

    2 4598H–AUTO–03/07 ATA5283 2. Pin Configuration Figure 2-1. Pinning TSSOP8 L VDD 3 4 2 1 N_DATA N_WAKEUP RESET COIL 8 7 6 5 TST2 TST1 VSS Figure 2-2. Pin Description Pin Symbol Functi on 1 COIL Antenna coil input 2 TST1 T est pin (reserved) 3 TST2 T est pin (reserved) 4 VSS Signal ground 5 RESET Externa l reset input 6 N_D A T A Data signal 7 N[...]

  • Page 3

    3 4598H–AUTO–03/07 ATA5283 3. Functional Description The ATA5283 is an ultra-low pow er ASK receiver. Without a carr ier signal it operates in the standby listen mode. In this mode it monitors th e coil input with a very low current consu mption. To activate t he IC and the connected con trol unit, the transmit ting stage must send t he preambl[...]

  • Page 4

    4 4598H–AUTO–03/07 ATA5283 3.3 A utomatic Gain Control For a correct demodulation the signal conditione r needs appropriate interna l signal amplitude. To control the in put signal the ATA52 83 has a build in dig ital AGC. The gain control circuit regu- lates the internal signal amplitude to the reference value (Ref2, Figure 3-2 ). It de crease[...]

  • Page 5

    5 4598H–AUTO–03/07 ATA5283 3.4 Signal Conditioner The signal conditioner d emodulates the amplifier outp ut signal and conver ts it to a binary signal. It compares the carrier signa l with the 50% reference level (see Ref 1 in Figure 3-3 ) and delivers a logical 1, if the carrier signal stays below th e reference and a logical 0, if it exc eeds[...]

  • Page 6

    6 4598H–AUTO–03/07 ATA5283 Figure 3-5. Turn Off Delay Time (t off ) versus Antenna Q- Factor 3.5 Data Output The data output N_DATA outputs the demodulated and digitized LF signal according to the envelope of the ante nna input signal. In the standby mode the N_DATA ou tput is disabled and set to level 1. It is enabled by t he wake-up si gnal a[...]

  • Page 7

    7 4598H–AUTO–03/07 ATA5283 3.8 Standb y Listen Mode In the standby listen mode the IC monitors the co il input with a very low current consumption. The automatic gain control is switched off and the gain is set to the maximum value. The N_DATA and the N_WAKEUP outp ut are set to a high level. Before the controller enters its standby mode after [...]

  • Page 8

    8 4598H–AUTO–03/07 ATA5283 Figure 3-7. Pin Connection an d Pin Protection Figure 3-8. Coil Input Impe dance 2 k Ω Divider impedance 143 k Ω to 5 M Ω 2 k Ω 7 VDD VDD N_W AKEUP N_D A T A RESET VDD TST1 TST2 VSS COIL_X 6 VDD A T A5283 VDD VDD 1 k Ω VDD 5 8 2 3 4 1 1 100 1000 10000 10 10000 1000 100 Coil Input Signal (mV pp ) Z (k Ω ) m[...]

  • Page 9

    9 4598H–AUTO–03/07 ATA5283 4. Absolute Maxim um Ratings Stresses beyond those listed under “Absolute Maximum Ratings” may cause per manent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions bey ond t hose indicated in the operational sectio ns of this specification is n[...]

  • Page 10

    10 4598H–AUTO–03/07 ATA5283 7. Electrical Characteristics V SS = 0V , V DD = 2V to 3.8V , T amb = –40 ° C to +105°C, characterized up to 125°C , unless other specified No. Parameter s T est Conditions Pin Symbol Min. T yp. Max. Unit T ype* 1 P ower Supply and Coil Limiter 1.1 P ower supply 8 V DD 23 . 23 . 8 V A 1.2 Reset supply current ?[...]

  • Page 11

    11 4598H–AUTO–03/07 ATA5283 3 Automatic Gain Control 3.1 Preamble detection time V IN ≥ 3m V rms at 125 kHz t DAGC 19 2 P er iods B 3.2 AGC adjustment time f = 125 kHz V IN = 1 mV rms V IN = 3 mV rms V IN = 30 mV rms V IN = 100 mV rms V IN = 1V rms t AGC t AGC t AGC t AGC t AGC 0 48 220 292 450 512 P er iods C 3.3 Signal change rate (gap dete[...]

  • Page 12

    12 4598H–AUTO–03/07 ATA5283 9. P acka g e Inf ormation 8. Or dering Information Extended T ype Number P acka ge Remarks A T A5283P-6AQJ TSSOP8L 5000 pieces, taped and reeled, Pb-free A T A5283P-6APJ TSSOP8L 500 pieces, taped and reeled, Pb-free 3 ±0.1 0.85 ±0.05 0.1 ±0.05 specifications according to DIN technical drawings Issue: 2; 15.03.04 [...]

  • Page 13

    13 4598H–AUTO–03/07 ATA5283 10. Revision History Please note that the follo wing page numbers referred to in this section re f er to the specific revision mentioned, not to this document. Revision No. History 4598H-A UT O-03/07 • Number 5.2.1 in section 7 “Electr ical Character istics” on page 11 added 4598G-A UTO-01/07 • Put datasheet [...]

  • Page 14

    Disclaimer: The information in this d ocument is provided in conn ection with Atmel products. No license, ex press or impli ed, by estoppel or otherwise, to any intellectual proper ty r ight is granted by this document or in connection with the sale of Atm el products. EXCEPT AS SET FORTH IN A TMEL ’S TERMS AND CONDI- TIONS OF SALE LOCA TED ON A [...]