English dropdown-ico

Bock Water heaters 20E manual

1
2
3
4
5
6
7
8
9
10
11
12

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Bock Water heaters 20E, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Bock Water heaters 20E one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Bock Water heaters 20E. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Bock Water heaters 20E should contain:
- informations concerning technical data of Bock Water heaters 20E
- name of the manufacturer and a year of construction of the Bock Water heaters 20E item
- rules of operation, control and maintenance of the Bock Water heaters 20E item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Bock Water heaters 20E alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Bock Water heaters 20E, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Bock Water heaters service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Bock Water heaters 20E.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Bock Water heaters 20E item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    TO THE CONSUMER: Read these and all com- ponent instructions. Please keep for future reference. Please re- member to return the registration card. W aranty , registration card & parts list included. TO THE INST ALLER: Please attach these in- structions next to the w ater heater . BOCK RESIDENTIAL OIL-FIRED W A TER HEA TERS Model numbers: 20e, 2[...]

  • Page 2

    –2– THIS MANUAL HAS BEEN PREP ARED T O ACQUAINT YOU WITH THE INST AL- LA TION, OPERA TION, AND MAINTENANCE OF YOUR W A TER HEA TER AND T O PROVIDE IMPOR T ANT SAFETY INFORMA TION. Read all instructions thoroughly before attempting installation or operation of the water heater . Keep these and all component instructions for future reference. The[...]

  • Page 3

    The drain valve fitting may be used as an alternate cold water inlet on heaters equipped with a dip tube, as shown in Figure 3. By plumbing a “T” into the drain fitting, the cold water inlet can be re lo cated to this point. The dip tube must be removed and its fitting plugged. Figure 3 also shows a copper loop heat trap installed on the hot wa[...]

  • Page 4

    –4– Inspect the incoming water line for check valves or water pressure reducing v alves. Any type of check valve may cause pressure to build up in the heater and cause tank failure. If the heater is installed in a closed system or if backflow pre- v enters and pressure regulators are installed, add an expansion tank. Do not try to heat hard wat[...]

  • Page 5

    –5– PLACE THE W A TER SYSTEM IN OPERA TION Warning: Handhole cover may loosen during shipping – check for tightness before putting heater in operation. For any horizontal run exceeding the maximum length specified in Figure 4, or any lift of more than 10 feet, a booster pump must be used. Booster pumps may b e obtained from Sun T ec Hydraulic[...]

  • Page 6

    –6– 5 . While the burner is operating, disconnect one of the yellow cad cell wires. Check to see that the burner control locks out in the time specified on the control. R eattach the wire and reset the control. The burner should restart. Note: Y ou may have to wait a minute before resetting the control. 6. The thermostat is factory set at 120°[...]

  • Page 7

    –7– SERVICE 1. Check the fuel supply , electrical wiring and fuses, and make sure temperature c ontrol is calling for heat. 2. If the motor runs but there is no flame, remove the electrode assembly , clean, readjust to the burner manufacturer ’s specifications, check the electrode porce- lain for cracks and replace if necessary . Check the tr[...]

  • Page 8

    L4080B L4006A FIGURE 8 : Honeywell L4006A w/ L8080B For Models: 50, 120E FIGURE 6 : Beckett or Wayne burner w/ Carlin EZ-T emp F or Models: 32, 33, 40, 50, 51, 71, 120E FIGURE 7 : Honeywell L4103A-1 142 For Models: 32, 33, 40, 51, 71E FIGURE 7 NOTES: Set point 120 ° FIGURE 4 NOTES: High limit: 190 ° Aquastat: 120° set point 15 ° dif ferential ?[...]

  • Page 9

    –9– ITEM DESCRIPTION 1. Cold W ater Inlet Dip T ube (N/A 33E & 40E) 2. Plastic Cap 3. Magnesium Anode Rod (aluminum avaliable) 4. Name Plate/Rating Label 6. Immersion W ell & Aquastat 8. Drain V alve 9. Mounting Bracket Gasket 10. Burner Mounting Bracket (part of jacket assembly on Models 20e, 32E through 51 Series; sold separately on 7[...]

  • Page 10

    – 10 – LIMITED W ARRANTY This warranty covers “Bock” W ater Heater models 20e, 20pp, 32E, 32EC, 32PP , 32PPC, 33E, 33PP , 40E, 40PP , 50ES, 50ESC, 51E, 51EC, 51PP , 51PPC, 71E and 120E. Bock W ater Heaters, Inc., a division of Bock Corporation–a Wisconsin corporation–at 1 10 South Dickinson Street, Madison, WI 53703 (“Company”), war[...]

  • Page 11

    – 11 – BOCK BURNER MODEL/ MAX MODEL MAX MODEL (OIL) MFR. OEM # INPUT OEM # INPUT 32E, 32EC, 33E W A YNE MSR/371-001B 0.75 X 80A 32PP , 32PPC W A YNE HS/371-009HS 0.75 X 80A 40E W A YNE MSR/371-030B 0.90 X 70A 5IE, 51EC W A YNE MSR/371-003B 1.10 X 80A 50ES, 120E W A YNE MSR/371-029B 1.10 X 80A 51PP , 51PPC W A YNE HS/371-01 1HS 1.10 X 80A 71E W [...]

  • Page 12

    – 12 – Bock W ater Heaters, Inc. 1 10 South Dickinson Street • P .O. Box 8632 • Madison, WI 53708-8632 Phone: 608/257-2225 • Fax: 608/257-5304 • www .bockwaterheaters.com Form 23420 Rev 4 3/2007[...]