Go to page of
Similar user manuals
-
Stereo Amplifier
Boston Acoustics 2
8 pages 1.29 mb -
Stereo Amplifier
Boston Acoustics BRAVO 2
8 pages 1.35 mb -
Stereo Amplifier
Boston Acoustics 1005
12 pages 0.46 mb -
Stereo Amplifier
Boston Acoustics GT-2300
12 pages 1.31 mb -
Stereo Amplifier
Boston Acoustics GT-2200
12 pages 1.31 mb -
Stereo Amplifier
Boston Acoustics GT-275
12 pages 1.31 mb -
Stereo Amplifier
Boston Acoustics GT-2125
12 pages 1.31 mb -
Stereo Amplifier
Boston Acoustics GT-20 GT-222
19 pages 0.62 mb
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of Boston Acoustics GT-28, GT-24, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Boston Acoustics GT-28, GT-24 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of Boston Acoustics GT-28, GT-24. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of Boston Acoustics GT-28, GT-24 should contain:
- informations concerning technical data of Boston Acoustics GT-28, GT-24
- name of the manufacturer and a year of construction of the Boston Acoustics GT-28, GT-24 item
- rules of operation, control and maintenance of the Boston Acoustics GT-28, GT-24 item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Boston Acoustics GT-28, GT-24 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Boston Acoustics GT-28, GT-24, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Boston Acoustics service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Boston Acoustics GT-28, GT-24.
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the Boston Acoustics GT-28, GT-24 item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
-
Page 1
GT-28 GT-24 2-Channel, High-Curr ent/High-Power Amplifiers[...]
-
Page 2
2 T able of Contents Parts List 3 Features and Specifications 3 Control Functions 4 Control functions (cont.) 5 Mechanical Functions 6 Recessed RCA inputs 6 Control cover r emoval and reinstallation 6 Multi-position mounting feet 6 V ents (side and rear) 6 Mechanical functions (cont.) 7 Amplifier linking 7 Wi re connection 7 Fuses 7 General Insta[...]
-
Page 3
Included Hardwar e: GT -28 & GT -24 (1) owner’ s manual (1) female quick-connect terminal for remote input (1) 2mm hex wrench (for speaker input) (1) 3mm hex wrench (for power input) (6) mounting screws 3 Parts List Te chnical Specifications GT -28 GT -24 14.4VDC Power @ 4 Ohms 2x250W 2x175W @ 2 Ohms 2x450W 2x275W @ 4 Ohms (mono) 1x900W 1x55[...]
-
Page 4
4 12.6–14.4VDC B+ B+ GROUND GND GND FUSE 4 x 25A SPEAKER OUTPUT L R MONO LOWPASS OFF ON HIGHPASS OFF ON 5 0.2 INPUT SENSITIVITY 2.6 50 350 Hz 200 20 350 Hz 185 0.7 1.2 Q/HP 0.95 LOWPASS SLOPE 12dB 24dB MONO 12dB ST INPUT STEREO MONO L SUBWOOFER LEVEL OFF ON REMOTE INP U T SUBWOOFER LEVEL Contr ol Functions RCA Inputs RCA cables from head unit or [...]
-
Page 5
Lowpass Crossover Contr ols To use lowpass crossover move LOWP ASS switch to righthand position. Lowpass crossover fr equency is adjustable from 50Hz to 350Hz by r otary control. (Moving switch to left-hand position will bypass crossover functions.) Lowpass Slope Select appropriate cr ossover slope of 12 or 24dB/octave by moving LOWP ASS SLOPE swit[...]
-
Page 6
6 Mechanical Functions Recessed RCA Inputs The input jacks are r ecessed into the body of the amplifier to provide clear- ance in tight mounting locations. Control Cover Removal and Reinstallation The cover panel is secured with two (2) captive coin-slotted scr ews. Coin-slot- ted screws allow a coin edge to be used as a scr ewdriver to remove the[...]
-
Page 7
7 Mechanical Functions (cont.) Amplifier Linking The design of the side panels enables multiple amplifiers to be used together without additional hardwar e. Wire Connection Amplifier accepts stripped wire dir ectly into the terminal blocks. Speaker outputs accept 8-gauge, and the DC power and ground accept 4-gauge. Tighten with supplied hex wren[...]
-
Page 8
8 Before Y ou Install Before you install the unit, disconnect the negative (–) battery cable in the engine compartment of the vehi- cle. Doing so will prevent damage to both the electrical system of the vehicle and the amplifier during installation. Wire Routing Do not run the power wire near any low-level signals or audio cables such as the RCA[...]
-
Page 9
9 57mm (2 1 / 2 ") Choose the Mounting Location Plan your installation so that the amplifier is mounted where adequate ventilation is available. Never mount an amplifier in the engine compartment of a vehicle! W ARNING! Before driving the mounting scr ews thr ough any surface, be sure of what is behind that sur- face. Check for gas tank, bra[...]
-
Page 10
10 Passenger and T runk Compartment Mounting If the amplifier is mounted under a seat, be sure that the vents do not become blocked. Do not allow seat padding or other obstructive material to press down on the amplifier . All Boston GT amplifiers have top panel controls. If the amplifier is mounted under a seat, position the amplifier so the c[...]
-
Page 11
SPEAKER OUTPUT L R MONO Power/B+ and Power/GND Connection Strip approximately 5 / 8 " (16mm) of insulation. The positive (+) power wir e is installed into the amplifier terminal marked “B+”. The negative (–) wire is installed into the terminal marked “GND”. The ground wir e should be as short as possible and connected directly to th[...]
-
Page 12
12 Mono Subwoofer Operation When the amplifier is configured for mono operation, use the speaker output terminals marked for mono use. W ARNING! Subwoofer impedance must not fall below 2 ohms when in MONO mode. Installation—Fuses and Wiring (cont.) 1) Music The material chosen for head unit/amplifier system setup must be both clear in recor di[...]
-
Page 13
13 Setup T uning—Full-Range Speakers (cont.) 4) Head Unit The head unit should have all controls such as bass, tr eble, balance, and fader set to the flat or centered position. The volume control should be at the minimum setting. If the head unit has any equalization or bass management features such as boost , they should be defeated at this tim[...]
-
Page 14
14 8) “Q” Control Once the highpass crossover point has been determined, use the “Q” con- trol to incr ease the bass information centered ar ound the crossover point. Setting the “Q” control is done in conjunction with setting the levels on the input sensitivity and highpass crossover fr equency controls. Y ou may find while setting th[...]
-
Page 15
15 4) Input Sensitivity Control Tu rn control all the way counterclockwise (minimum position). In this position, the amplifier will be less sen- sitive to the input signal from the head unit. Slowly r otate this control clockwise until maximum undistorted playing level is heard fr om the subwoofer(s). Listen closely for faults such as bottoming fr[...]
-
Page 16
16 System Examples System A—Full-Range Front Speakers 6 . 5 L F 6 . 5 L F fuse to + battery terminal to gr ound to ground fuse to + battery terminal System B—Rear Fill Speakers fuse to + battery terminal to ground to gr ound fuse to + battery terminal 6 . 5 L F 6 . 5 L F[...]
-
Page 17
17 System Examples (cont.) System C—Parallel 4 Ω Subwoofers (2 Ω load) System D —Series/Parallel 2 Ω Subwoofers (2 Ω load) 10.5LF 4 Ω 10.5LF 4 Ω fuse to + battery terminal to ground to gr ound fuse to + battery terminal fuse to + battery terminal to gr ound to gr ound fuse to + battery terminal 10.5LF 2 Ω 10.5LF 2 Ω 10.5LF 2 Ω[...]
-
Page 18
18 Amplifier T r oubleshooting Guide Status LEDs on Amplifier not Lit — Head Unit (Sour ce) T urned “ON” V erify Remote turn-on wire fr om source to amplifier has pr oper voltage Power (B+) connections at amplifier , terminal blocks, and battery are secure Ground (GND) connections at amplifier and vehicle chassis ar e secure Battery B+ f[...]
-
Page 19
19 Contact and W arranty Information 300 J ubilee Drive Pe a b o d y, MA 0 1 960 U.S.A. (978) 538-5000 Boston, Boston Acoustics, and the Boston logo are r egister ed trademarks of Boston Acoustics, Inc. © 2003 Boston Acoustics, Inc. All rights reserved. Specifications subject to change without notice. P/N 042-1801-0 www .bostonacoustics.com Limit[...]