Go to page of
Similar user manuals
-
Boiler
Burnham MST288
64 pages 6.82 mb -
Boiler
Burnham 1099-01R1-/10
8 pages 1.92 mb -
Boiler
Burnham IN3
1 pages 0.03 mb -
Boiler
Burnham Gas-Fired
4 pages 0.88 mb -
Boiler
Burnham ALP285
100 pages 11.92 mb -
Boiler
Burnham C3
2 pages 0.8 mb -
Boiler
Burnham V8H Series
2 pages 0.6 mb -
Boiler
Burnham IN7
1 pages 0.03 mb
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of Burnham ALP150, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Burnham ALP150 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of Burnham ALP150. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of Burnham ALP150 should contain:
- informations concerning technical data of Burnham ALP150
- name of the manufacturer and a year of construction of the Burnham ALP150 item
- rules of operation, control and maintenance of the Burnham ALP150 item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Burnham ALP150 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Burnham ALP150, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Burnham service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Burnham ALP150.
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the Burnham ALP150 item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
-
Page 1
101602-01R2-9/08 Price - $5.00 D N A G N I T A R E P O , N O I T A L L A T S N I R O F S N O I T C U R T S N I E C I V R E S ™ E N I P L A Y C N E I C I F F E H G I H G N I S N E D N O C T N E V T C E R I D R E L I O B R E T A W T O H D E R I F - S A G As an ENERGY ST AR ® Partner , Burnham Hydronics has determined that the Alpine™ Series meet[...]
-
Page 2
2 IMPOR T ANT INFORMA TION - READ CAREFULL Y NOTE: The equipment shall be installed in accordance with those installation regulations enforced in the area where the installation is to be made. These regulations shall be carefully followed in all cases. Authorities having jurisdiction shall be consulted before installations are made. All wiring on b[...]
-
Page 3
3 W aRning This boiler requires regular maintenance and service to operate safely . Follow the instructions contained in this manual. improper insta llation, adjus tment, alterat ion, service or maintenance can cause property damage, personal injury or loss of life. Read and understand the entire manual before attempting installation, start-up oper[...]
-
Page 4
4 T able of Contents I. P roduct Description, Specifications and Dimensional Data.................... 4 II. P re-Installation ............................... 8 III. U npacking Boiler ........................... 9 IV . V enting ......................................... 10 V . Condensate Disposal .................... 29 VI. W ater P iping and T rim [...]
-
Page 5
5 Figure 1a: alpine™ - Models aLP080 thru aLP210[...]
-
Page 6
6 Figure 1B: alpine™ - Models aLP285 thru aLP399[...]
-
Page 7
7 T able 2a: Rating Data - Models aLP080 thru aLP399 (0 to 2000 Feet Elevation above Sea Level) T able 2B: Rating Data - Models aLP080 thru aLP399 (2001 to 7000 Feet Elevation above Sea Level) alpine Series gas-Fired Boilers Model Number * Input (MBH) ** Output (MBH) Net I=B=R Ratings W ater (MBH) AFUE % Thermal Efciency (%) Combustion Efcien[...]
-
Page 8
8 W aRning if you do not follow these instructions exactly , a re or explosion may result causing property damage or personal injury . DangER Do not install boiler where gasoline or other ammable vapors or liquids, or sources of hydrocarbons (i.e. bleaches, cleaners, chemicals, sprays, paint removers, fabric softeners, etc.) are used or store[...]
-
Page 9
9 iii. Unpacking Boiler CaUTiOn Do not drop boiler . A. Move boiler to approximate installed position. B. Remove all crate fasteners. C. Lift and remove outside container . D. Remove boiler from cardboard positioning sleeve on shipping skid. W aRning installation of this boiler should be undertaken only by trained and skilled personnel from a quali[...]
-
Page 10
10 iV . V enting W aRning Failure to vent this boiler in accordance with these instructions could cause products of combustion to enter the building resulting in severe property damage, personal injury or death. Do not interchange vent systems or materials unless otherwise specied. The use of thermal insulation covering pipe and ttings is pro[...]
-
Page 11
1 1 2. The Alpine™ is designed to be installed as a Direct V ent boiler . The air for combustion is supplied directly to the burner enclosure from outdoors and ue gases are vented directly outdoors (through wall or roof). 3. The following combustion air/vent system options are approved for use with the Alpine™ boilers: i. T wo-Pipe CPVC/PVC [...]
-
Page 12
12 V ent Pipe Pipe Direction Enclosure Minimum Clearance T o Combustible Material, Inches CPVC/PVC V enting V ertical or Horizontal Enclosed at all Sides 1” V ent/0” Combustion Air T able 5: Clearances from V ent Piping to Combustible Material V ent System Components Part Number Quantity ALP080 & ALP105 (P/N 102189-01) ALP150 & ALP210 ([...]
-
Page 13
13 Boiler Model 3” Combustion Air Pipe (Equivalent Length) 4” Combustion Air Pipe (Equivalent Length) 3” V ent Pipe (Equivalent Length) 4” V ent Pipe (Equivalent Length) Min. Max. Min. Max. Min. Max. Min. Max. ALP080 21-7/8 In. 60 Ft. --- --- 21-7/8 In. 60 Ft. --- --- ALP105 21-7/8 In. 60 Ft. --- --- 21-7/8 In. 60 Ft. --- --- ALP150 --- ---[...]
-
Page 14
14 6. Remove the Silicone ue sensor cap from the vent carton and press onto the two pipe vent system connector for CPVC/PVC sensor port. Remove the tape holding the ue sensor and insert the ue temperature sensor into the ue sensor plug until it is rmly engaged. See Figure 4. 7. Near-Boiler V ent Piping (see Figure 5): W aRning all CP[...]
-
Page 15
15 6. Install Rodent Screen and V ent T erminal (supplied with boiler), see Figure 8 for appropriate conguration. 7. Apply sealant between vent pipe and opening/ thimble to provide weather-tight seal. Sealant should not restrain the expansion of the vent pipe. Combustion Air Piping - Horizontal 1. See Paragraph D for instructions on attaching th[...]
-
Page 16
16 7. Install Rodent Screen and Combustion Air T erminal (supplied with boiler), see Figure 8 for appropriate conguration. 8. Apply sealant between vent pipe and opening to provide weather-tight seal F . CPVC/PVC V ertical V enting System Refer to Figures 3, 4, 5, 8, 9 & 10. nOTiCE Roof penetrations require the use of roof ashing and stor[...]
-
Page 17
17 a. Size roof opening to maintain minimum clearance of 1 inch from combustible materials. b. Extend vent pipe to maintain minimum vertical and horizontal distance of twelve (12) inches from roof surface. Allow additional vertical distance for expected snow accumulation. Provide brace as required. CaUTiOn V ertical venting requires the use of roof[...]
-
Page 18
18 7. Brace exterior piping if required. Combustion Air Piping - V ertical 1. See Paragraph D for instructions on attaching the vent system connector to the boiler . 2. Do not exceed maximum combustion air length. Refer to T able 7 for pipe diameters and allowable lengths. 3. Horizontal combustion air pipe must maintain a minimum ¼ inch per foot s[...]
-
Page 19
19 5. Install maximum vertical run of seven (7) feet of Schedule 40 PVC vent pipe. See Figure 1 1. 6. At top of vent pipe length install another PVC 90° elbow so that elbow leg is opposite the building’ s exterior surface. 7. Install Rodent Screen and Combustion Air T erminal (supplied with boiler), see Figure 8 for appropriate conguration. 8[...]
-
Page 20
20 Figure 12: Field installation of Boiler Concentric V ent Collar codes. Contact local building or re ofcials about restrictions and installation inspection in your area. 2. Horizontal vent pipe must maintain a minimum ¼ inch per foot slope towards the boiler . 3. Use noncombustible ¾ inch pipe strap to support horizontal runs and maintain[...]
-
Page 21
21 The direct vent termination location is restricted as follows: a. Minimum twelve (12) inches above grade plus normally expected snow accumulation level, or minimum seven (7) feet above grade, if direct vent terminal is located adjacent to public walkway . Do not install the terminal over public walkway where local experience indicates that appli[...]
-
Page 22
22 b. Measure dimension “L” from exterior wall outer surface to the end of the last tting (or end of installed Boiler Concentric V ent Collar). See Figure 14 ‘Dimension “L”’. several marks around the outer pipe to establish a cut line. See Figure 15 ‘ Cutting Outer Pipe’. d. Carefully cut the outer pipe at the marked line using a[...]
-
Page 23
23 i. Install the supplied Inside W all Plate onto the shortened Horizontal (W all) T erminal interior end and move the plate to cover interior wall cut opening. Secure the plate with provided fasteners, then, apply the sealant around plate sides to seal it to interior wall. j. Lubricate the brown gasket inside boiler concentric vent collar or the [...]
-
Page 24
24 Figure 19: V ertical Concentric V ent installation outer pipes to start the screw . Use a drill stop or other means to ensur e that the drill bit does not penetrate more than 3/8” into the outer pipe. Do not use sheet metal screws longer than ½”. When Additional Concentric V ent Piping is needed 1. If additional concentric vent piping is ne[...]
-
Page 25
25 Figure 22: Cutting Straight Pipe Figure 23: Joining Cuttable Pipe Figure 24: Joining non-Cuttable Pipe b. Push the male end of the rst tting into the boiler collar until it bottoms out. The male end of cuttable sections should go 1” into the collar until the insertion mark (made in Step 2d above) is covered. On other ttings, the bead [...]
-
Page 26
26 Figure 26: Cutting V ertical T erminal a. Determine the centerline of the terminal location on the roof. For at roof, cut either 5-1/2” diameter hole (80/125 mm concentric vent size) or 6-1/2” diameter hole (100/150 mm concentric vent size) for the terminal. For sloped roof, cut a hole in the roof large enough for the terminal to pass thr[...]
-
Page 27
27 T able 10: Cut-T o-Length Extensions (Cuttable) Part No. Component Description Size 101 163-01 Cut-T o-Length Extension, 500 mm (19-1/2”) 80/125 mm 101 162-01 Cut-T o-Length Extension, 1000 mm (39”) 101550-01 Cut-T o-Length Extension, 500 mm (19-1/2”) 100/150 mm 101551-01 Cut-T o-Length Extension, 1000 mm (39”) Figure 27: Completing V er[...]
-
Page 28
28 Figure 28: Chimney Chase installation[...]
-
Page 29
29 V . Condensate Disposal A. Condensate T rap and Drain Line . 1. All condensate, which forms in the boiler or vent system, collects in the sump under heat exchanger and leaves the boiler through factory installed condensate trap. 2. The trap allows condensate to drain from sump while retaining ue gases in the boiler . The trap has factory inst[...]
-
Page 30
30 Figure 29: Condensate T rap and Drain Line[...]
-
Page 31
31 nOTiCE Oxygen contamination of boiler water will cause corrosion of iron and steel boiler components, and can lead to boiler failure. Burnham’s Standard W arranty does not cover problems caused by oxygen contamination of boiler water or scale (lime) build-up caused by frequent addition of water . Do not ll boiler with softened water to prev[...]
-
Page 32
32 1. ALP080 thru ALP285 Boiler Models a. Locate and remove ¾” NPT x close black nipple, ¾” NPT black tee, ¾” MPT x ¾” FPT Pressure Relief V alve, ¾” NPT Drain V alve. b. Install close nipple into tee branch, then, screw the assembly into boiler left side front ¾” tapping making sure tee run outlets are in vertical plane and paral[...]
-
Page 33
33 B. Piping System T o Be Employed. Alpine (ALP) boilers are designed to operate in a closed loop pressurized system. Minimum pressure in the boiler must be 12 PSI. Proper operation of the Alpine (ALP) boiler requires that the water ow through the boiler remain within the limits shown in T able 1 1, any time the boiler is ring. Boiler Model [...]
-
Page 34
34 T able 12a: Recommended Circulator Models for alpine (aLP) Boilers Based on 25°F T emperature Differential and Up to 75 ft. Equivalent Length Near-Boiler Piping - Space Heating Circulator Boiler Model Boiler Supply Connection, Inch, FPT Boiler Return Connection, Inch, FPT Near-Boiler Piping Supply Pipe Size, Inch Near-Boiler Piping Return Pipe [...]
-
Page 35
35 Boiler Model Boiler Supply Connecti on, Inch, FPT Boiler Return Connecti on, Inch, FPT Near- Boiler Piping Supply Pipe Size, Inch Near- Boiler Piping Return Pipe Size, Inch Max Allowable Flow thru Boiler , GPM @ 20°F Delta T Flow , GPM @ 25°F Delta T Min Req’d Flow thru Boiler , GPM @ 35°F Delta T Alliance SL Models to be installed As Part [...]
-
Page 36
36 T able 12B (continued): Space Heating with Indirect Water Heating - Recommended Circulator Models for Alpine (ALP) Boilers and Alliance SL Indirect W ater Heaters Installed as Part of Near-Boiler Piping Up to 75 Ft. Equivalent Length Boiler Model Boiler Supply Connecti on, Inch, FPT Boiler Return Connecti on, Inch, FPT Near- Boiler Piping Supply[...]
-
Page 37
37 T able 13: Fitting and V alve Equivalent Length Copper Fitting and Sweat V alve Equivalent Length (Ft) Fitting or V alve Description Copper Pipe or V alve Size 1 1¼ 1½ 90° Elbow 2.5 3.0 4.0 45° Elbow 1.0 1.2 1.5 T ee (thru ow) 0.5 0.6 0.8 T ee (Branch ow) 4.5 5.5 7.0 Diverter T ee (typical) 23.5 25.0 23.0 Gate V alve 0.3 0.4 0.5 Globe [...]
-
Page 38
38 Figure 31a: near Boiler Piping - Heating Only (with Central Heating Circulators)[...]
-
Page 39
39 Figure 31B: near Boiler Piping - Heating Only (with Central Heating zone V alves)[...]
-
Page 40
40 Figure 32a: near Boiler Piping - Heating Plus indirect W ater Heater (with Central Heating Circulators)[...]
-
Page 41
41 Figure 32B: near Boiler Piping - Heating Plus indirect W ater Heater (with Central Heating zone V alves)[...]
-
Page 42
42 Figure 32C: near Boiler Piping - Heating (with Central Heating Circulators) Plus alternately Piped indirect Water Heater[...]
-
Page 43
43 Figure 32D: near Boiler Piping - Heating (with Central Heating zone V alves) Plus alternately Piped indirect W ater Heater[...]
-
Page 44
44 nOTiCE Where it is not possible to install a separate boiler loop, the system circulator must be sized to ensure that the ow through boiler stays within the dened parameters to prevent overheating when the boiler is red at it’ s full rated input. Install a ow meter to measure the ow , or re the boiler at full rate and ensure [...]
-
Page 45
45 D. Special Situation Piping Installation Requirements Observe the following guidelines when making the actual installation of the boiler piping for special situations: 1. Systems containing high level of dissolved oxygen – Many hydronic systems contain enough dissolved oxygen to cause severe corrosion damage to Alpine (ALP) boiler heat exchang[...]
-
Page 46
46 Vii. gas Piping W aRning Failure to properly pipe gas supply to boiler may result in improper operation and damage to the boiler or structure. always assure gas piping is absolutely leak free and of the proper size and type for the connected load. an additional gas pressure regulator may be needed. Consult gas supplier . A. Size gas piping . Des[...]
-
Page 47
47 T able 14B: Maximum Capacity of Schedule 40 Black Pipe in CFH* (LP gas) For gas Pressures of 0.5 psig or Less inlet Pressure 1 1.0 inch W .C.; 0.3 inch W .C. Pressure Drop Nominal Pipe Size, In. Inside Diameter , In. Length of Pipe, Ft. 10 20 30 40 50 60 70 80 90 100 ½ 0.622 88 60 48 41 37 33 31 29 27 25 ¾ 0.824 184 126 101 87 77 70 64 60 56 5[...]
-
Page 48
48 C. Pressur e test. See T able 17 for Alpine Min./Max. Pressure Ratings. The boiler and its gas connection must be leak tested before placing boiler in operation. 1. Protect boiler gas control valve. For all testing over ½ psig, boiler and its individual shutoff valve must be disconnected from gas supply piping. For testing at ½ psig or less, i[...]
-
Page 49
49 Viii. Electrical A. General. Install wiring and electrically ground boiler in accordance with authority having jurisdiction or , in the absence of such requirements, follow the National Electrical Code , NFP A 70, and/or CSA C22.1 Electrical Code. B. A separate electrical circuit must be run from the main electrical service with an over-current [...]
-
Page 50
50 • Black – Line voltage “hot” • White – “Neutral” for boiler and circulators • Red – “Heating” circulator “hot” • Blue – “Indirect W ater Heater “ circulator “hot” • Green – Ground connection 2. Maximum circulator continuous current draw is 2A. W ith primary/secondary piping, it may be desirable to use [...]
-
Page 51
51 Figure 35: Wiring Connections Diagram[...]
-
Page 52
52 Figure 36: Ladder Diagram[...]
-
Page 53
53 Figure 37A: Modied Wiring For DHW Priority When Using Low Flow Circulator Piped Off System Header - Heating (with Central Heating Circulators) Plus alternately Piped indirect Water Heater[...]
-
Page 54
54 Figure 37B: Modied Wiring For DHW Priority When Using Low Flow Circulator Piped Off System Header - Heating (with Central Heating zone V alves) Plus alternately Piped indirect W ater Heater[...]
-
Page 55
55 Figure 38: Wiring for MCBa Modulating Boiler Control Time Delay Relay Box 5. If the boiler installation site may be subject to low supply voltage conditions or “brownouts”, that would affect MCBA Modulating Boiler Control operation, a separate optional T ime Delay Relay Box (P/N 101693-01) installation is strongly recommended. See Figure 38 [...]
-
Page 56
56 iX. Boiler Stacking For installations with unusually high space heating and/or domestic hot water heating loads, where employing two (2) Alpine (ALP) boilers will offer the benets of greater operational efciency , oor space savings and boiler redundancy , the Alpine (ALP) boilers may be installed stacked one on the top of the other . Re[...]
-
Page 57
57 vertical (roof) vent terminals, if level with each other , are spaced no closer then 12 inches horizontally . If vertical vent terminals cannot end in one plane, they must be spaced no closer then three (3) feet horizontally . Follow instructions in Section IV “V enting” of the manual for specics of individual boiler vent termination. Fol[...]
-
Page 58
58 X. Modular installation A. General Guidelines 1. Read and follow all venting, combustion air, water piping, gas piping and electrical instructions contained in the Installation, Operating and Service Instructions unless otherwise instructed in this section. 2. Consult Local Building Codes or National Fuel Gas Code, NFP A 54/ANSI Z222.3 for restr[...]
-
Page 59
59 Figure 40: Modular Boiler Direct V ent T ermination[...]
-
Page 60
60 Figure 41: Modular Boiler Concentric V ent T ermination[...]
-
Page 61
61 If vertical vent terminals cannot end in one plane, they must be spaced no closer than three (3) feet horizontally . 6. Chimney chase concentric venting is permitted for modules, when stackable, providing concentric vertical (roof) vent terminals, if level with each other , are spaced no closer then 12 inches horizontally . If vertical vent term[...]
-
Page 62
62 Figure 42: Modular Boiler W ater Piping w/Domestic Hot Water Heater nOTiCE installing a low water cutoff in the system piping of modular boilers is strongly recommended and may be required by Local Codes.[...]
-
Page 63
63 Figure 43: Modular Boiler W ater Piping w/Domestic Hot Water Heater (Continued)[...]
-
Page 64
64 Figure 44: Modular Wiring Diagram w/T ekmar 265 Control T ekmar 265 Based Control System (or equal) Sequence of Operation The T ekmar 265 Control (or equal) can control either 3 modulating boilers or 2 modulating boilers and an Indirect W ater Heater . When a call for heat is received by the T ekmar 265 Control, the control will re either one[...]
-
Page 65
65 T ekmar 264 Based Control System (or equal) Sequence of Operation The T ekmar 264 Control (or equal) can control up to four (4) boilers and an Indirect W ater Heater by utilizing stage ring. When a call for heat is received by the T ekmar 264 Control, the control will re either one or more boilers in sequential ring mode to establish a [...]
-
Page 66
66 A. V erify that the venting, water piping, gas piping and electrical system are installed properly . Refer to installation instructions contained in this manual. B. Conrm all electrical, water and gas supplies are turned off at the source and that vent is clear of obstructions. C. Conrm that all manual shut-off gas valves between the boile[...]
-
Page 67
67 Alpine™ Series Lighting and Operating Instructions Figure 46: Lighting instructions[...]
-
Page 68
68 H. Purge Air Fr om Gas T rain Upon initial start-up, the gas train will be lled with air . Even if the gas line has been completely purged of air , it may take several tries for ignition before a ame is established. If more than 5 tries for ignition are needed, it will be necessary to press the reset button to restart the boiler . Once a ?[...]
-
Page 69
69 Boiler Model Gas V alve Size (NPT) (Dungs) Gas V alve Model Fuel Converted Planned Installation Altitude Range From T o ALP080 1/2” GB-WND 055 D01 S00 253082 Natural Gas LP 0 - 7,000 Ft. ALP105 GB-WND 055 D01 S00 253083 ALP150 ALP210 GB-WND 055 D01 S00 253084 ALP285 3/4” GB-WND 057 D01 S00 253085 ALP399 GB-WND 057 D01 S00 253086 3. If conver[...]
-
Page 70
70 6. After the burner lights, force the burner to high re by simultaneously pressing and holding the “Mode” button and “+“ button. After a few seconds, the display should ash “H”, indicating that the boiler has been driven to high re. Allow the boiler to operate for approximately 5 minutes before taking combustion readings. No[...]
-
Page 71
71 Fuel Inlet Pressure (Inches w .c.) Min. Max. Natural Gas 4.0 14.0 LP 1 1.0 14.0 T able 24: inlet Pressure Limits • Apply the “Boiler Conversion Label” to a conspicuous surface on, or adjacent to, the outer boiler jacket. Fill in the date of the conversion and the name and address of the company making the conversion with a permanent marker[...]
-
Page 72
72 Xii. Operation A. The Alpine (ALP) boiler uses a microprocessor based Honeywell control, known as a “MCBA”, to manage all boiler functions including ame supervision and modulation. T wo set point or “target” boiler supply temperatures are stored in the MCBA ’ s memory; one for space heating and one for domestic water production. If [...]
-
Page 73
73 T able 25: Parameter Descriptions Access Code Paramet er No. Description Factory Setting ALP080 ALP105 ALP150 ALP210 ALP285 ALP399 no access Code needed 1 T3set DHW 140 2 DHW system 1 (On) 3 CH system 1 (On) 4 T1top CH Mode 190 Access Code Required 5 T1foot CH Mode 130 6 T4 minimum 0 7 T4 maximum 60 8 T4 frost protection * -22 9 T4 correction 0 [...]
-
Page 74
74 Figure 50: Basic Menu T ree[...]
-
Page 75
75 D. T wo basic types of errors codes are shown on the display: 1. Soft Lockout Codes – When a soft lockout occurs, the boiler will shut down and the display will alternate between the number “9” and the letter “b” followed by a two digit service code. A list of these codes, and their meanings, is shown in T able 29 in Section XIV Troubl[...]
-
Page 76
76 Figure 51: Outdoor Reset Curve II. Field Adjustable Boiler Operating Parameters MCBA control factory programmed operating parameters will result in satisfactory operation under most conditions. However , because all systems are different, there may exist situations where boiler operation may be enhanced by adjusting a few of these parameters in [...]
-
Page 77
77 Figure 52: Expanded Menu T ree (Cont’d on next page)[...]
-
Page 78
78 Figure 52: Expanded Menu T ree (cont’d.) Figure 53: adjusting Boiler Water Reset Curve[...]
-
Page 79
79 14; Parameter 13 denes the “thousands” and hundreds” places and Parameter 14 denes the “tens” and “ones” places. The ignition fan speed is only adjustable in increments of hundreds, so only one parameter (19) is required to dene it. IMPOR T ANT : Field adjustment of fan speeds is not recommended. b. In some cases one two-d[...]
-
Page 80
80 B. Adjusting Parameters via Personal Computer with GCI Interface 1. Operating System Requirements The GCI Interface requires a PC computer running a W indows 98/NT/2000 or XP operating system. In addition, the PC must have an open serial port. 2. Connecting Personal Computer to MCBA Control a. Connect the serial cable from the GCI to the compute[...]
-
Page 81
81 Figure 55: gascom Menu T ree 4. Double-click on the desired parameter . A window will open with either a eld or a pull down list of options will appear . Enter or select the desired value for the parameter . 5. Click OK. 6. Repeat Steps (3) - (5) to change any other desired parameters. 7. After all parameters have been changed, click on the ?[...]
-
Page 82
82 III. Component T est Procedur es A. Flame Signal Check 1. The ame signal can be checked between terminal number 7 on the low voltage terminal strip and ground. A good signal reading should be 6 VDC or greater . Hotwater - Indirect water heater thermostat (“1” = Calling, “0” = Not Calling) Pump - Heating circulator (“1” = On, “0?[...]
-
Page 83
83 T able 27: nTC Sensor Resistance V alues[...]
-
Page 84
84 Xiii. Service and Maintenance nOTiCE W arranty does not cover boiler damage or malfunction if the following steps are not performed at the intervals specied. A. Continuously: 1. Keep the area around the boiler free from combustible materials, gasoline and other ammable vapors and liquids. 2. Keep the area around the combustion air inlet te[...]
-
Page 85
85 3. Inspect the wiring to verify the conductors are in good condition and attached securely . CaUTiOn Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. V erify proper operation after servicing. 4. Remove the ignition electrode and inspect it for oxides. Clean the oxides from [...]
-
Page 86
86 b. Equivalent system freeze protection products may be used in lieu of product referenced above. In general, freeze protection for new or existing systems must use specially formulated glycol, which contains inhibitors, preventing the glycol from attacking the metallic system components. Insure that system uid contains proper glycol concentra[...]
-
Page 87
87 Figure 57: Condensate Overow Switch Orientation[...]
-
Page 88
88 XiV : T roubleshooting Figure 58: MBCa Fuse Location CONDITION POSSIBLE CAUSES Display Blank, Fan off, L WCO lights off • No 120V AC Power at boiler . Check breaker and wiring between breaker panel and boiler Display Panel Blank, Fan running • Loose 120V AC connection wiring between boiler J-Box and MCBA • Blown “F1” fuse in MCBA (see [...]
-
Page 89
89 B. T rouble shooting problems wher e a soft lockout code is displayed. When a soft lockout occurs, the boiler will shut down and the display will alternate between the number “9” and the letter “b” followed by a two digit service code. The boiler will automatically restart once the condition that caused the lockout is corrected. CODE CON[...]
-
Page 90
90 T able 30: Hard Lockout Codes Displayed CODE CONDITION POSSIBLE CAUSES E 00 A ame signal was present when there should be no ame. • Defective gas valve - make sure inlet pressure is below maximum on rating plate before replacing valve. E 02 Flame failure after 5 tries to restart • No gas pressure • Gas pressure under minimum value sh[...]
-
Page 91
91 XV . Repair Parts All Alpine™ Series Repair Parts may be obtained through your local Burnham Wholesale distributor . Should you require assistance in locating a Burnham distributor in your area, or have questions regarding the availability of Burnham products or repair parts, please contact Burnham Customer Service at (717) 481-8400 or Fax (71[...]
-
Page 92
92 Key No. Description (Quantity) Part Number ALP080 ALP105 ALP150 ALP210 ALP285 ALP399 1 Heat Exchanger , Burner , Etc. (Key No’s 2 thru 23) 101520-01 101521-01 101522-01 101523-01 101524-01 101525-01 2 Heat Exchanger Assembly 101710-01 10171 1-01 101712-01 101713-01 101714-01 101715-01 3 Burner Assembly 101717-01 101718-01 101719-01 101720-01 1[...]
-
Page 93
93 Key No. Description (Quantity) Part Number ALP080 ALP105 ALP150 ALP210 ALP285 ALP399 23 Gas T rain Assembly (Key No’s 24 thru 29) 101585-01 101585-02 101585-03 101585-04 101585-05 101585-06 24 Blower 101527-01 101528-01 101529-01 101530-01 25 Blower Inlet Shroud Assembly 101704-01 101704-02 101704-03 101704-04 26 Blower Outlet Gasket 101345-01[...]
-
Page 94
94 Key No. Description (Quantity) Part Number ALP080 ALP105 ALP150 ALP210 ALP285 ALP399 35 Air Pressure Switch 80160762 101862-01 36 Air Pressure Switch Hose 7016039 7016046 37 Rubber Grommet, Condensate T rap 101595-01 38 Condensate T rap, Blow Molded 101239-01 39 Spring Clip, Condensate T rap (2) 101632-01 40 Blocked Condensate Drain Switch 10158[...]
-
Page 95
95 Key No. Description (Quantity) Part Number ALP080 ALP105 ALP150 ALP210 ALP285 ALP399 42 Wiring Harness (Not Shown) 101454-01 43 MCBA Slide Out Assembly (Includes all parts shown) 101230-01 44 Control Panel, MCBA 101219-01 45A MCBA (programmed - 0-2000’ or 0-7000’) 101866-01 101866-02 101866-03 101866-04 10186 6-05 101866-06 45B MCBA (program[...]
-
Page 96
96 Key No. Description (Quantity) Part Number ALP080 ALP105 ALP150 ALP210 ALP285 ALP399 30 Rubber Grommet, Gas Line 820SOL0001 101638-01 51 Jacket, Rear/Bottom Panel 101217-01 101217-02 101217-03 101217-04 101764-01 101764-02 52 Lower Front Door Assembly 101227-01 101227-02 53 Draw Latch 101037-01 54 Jacket, Left Side Panel 101215-01 101215-02 1012[...]
-
Page 97
97 Key No. Description (Quantity) Part Number ALP080 ALP105 ALP150 ALP210 ALP285 ALP399 34 Flue T emp Sensor 101687-01 42 Wire Harness (Not Shown) 101454-01 72 Concentric V ent Collar with Viton Cap 101598-01 101599-01 76 V ent T erminal Kit 101808-01 101809-01[...]
-
Page 98
98 Key No. Description (Quantity) Part Number ALP080 ALP105 ALP150 ALP210 ALP285 ALP399 M iSCELLanEOUS P aRTS CaRTOn 101777-01 101777-02 101777-03 73 T emperature/Pressure Gauge 8056169 74 External Gas Shut Off V alve 806SOL0005 101615-01 75 Relief V alve 81660363 81660302 77 Boiler Drain V alve 806603061 78 Boiler Stacking Brackets (4) 101679-01 7[...]
-
Page 99
99 important Produc t Safety informa tion Refractory Ceram ic Fiber Product Warning : The Repair Parts list designates parts that contain refracto ry ceramic fibers (RCF). RCF has been classified as a possible human carcinogen. When exposed to temperatures about 1805°F, su ch as during direct flame contact, RCF changes into crystalline silica, a k[...]
-
Page 100
100 e. Boilers installed outside the 48 contiguous United States, the State of Alaska, and Canada. f. Damage to the boiler and /or property due to installation or oper ation of the boiler that is not in accordance with the boiler installation and operating instruction manual. g. An y damage of f ailure of the boiler resulting from hard water or sca[...]