Cadillac 2008 DTS manual

Seats and Restraint Systems ........................... 1 - 1 Front Seats ............................................... 1 - 2 Rear Seats ............................................... 1 - 9 Safety Belts ............................................. 1-10 Child Restraints ....................................... 1-31 Airbag System .................[...]

GENERAL MOTORS, GM, the GM Emblem, CADILLAC, the CADILLAC Crest & Wreath, and the name DTS are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. We reserve the right to make changes after that time without notice. For vehicles first sold in Canada, substitute the name ?[...]

Using this Manual Many people read the owner manual from beginning to end when they first receive their new vehicle to learn about the vehicle’s features and controls. Pictures and words work together to explain things. Index A good place to quickly locate information about the vehicle is the Index in the back of the manual. It is an alphabetica[...]

Vehicle Damage Warnings You will also find notices in this manual. Notice: These mean there is something that could damage your vehicle. A notice tells about something that can damage the vehicle. Many times, this damage would not be covered by your vehicle’s warranty, and it could be costly. The notice tells what to do to help avoid the damage.[...]

Front Seats ..................................................... .1-2 Power Seats ................................................. .1-2 Power Lumbar .............................................. .1-2 Massaging Lumbar ........................................ .1-3 Heated and Cooled Seats ............................... .1-3 Memory Seat, Mirrors an[...]

Front Seats Power Seats The power seat controls are located on the outboard side of the seats. • Move the seat forward or rearward by sliding the control forward or rearward. • Raise or lower the front part of the seat cushion by moving the front of the control up or down. • Raise or lower the rear part of the seat cushion by moving the rear [...]

Massaging Lumbar If your vehicle has this feature, the switch is located on the outboard side of the front seats behind the lumbar switch. Press the switch to turn the massaging lumbar feature on. The ignition must be on. The massage cycle will run for up to 10 minutes. To stop massage, press the massaging lumbar switch again, or press the power lu[...]

Press a button to turn on the desired feature. A light on that button will display to show which feature is on. There are three temperature settings for each feature. A column of three lights next to the buttons will display which setting the feature is in: high, medium or low. Three lights indicate the highest setting, two lights for medium and on[...]

A second seating, mirror, and steering wheel position can be programmed by repeating the above steps and pressing button 2 for a second driver. To recall your memory positions, the vehicle must be in PARK (P). Press and release either button 1 or button 2 corresponding to the desired driving position. The seat, outside mirrors, and steering wheel w[...]

Power Reclining Seatbacks Your seats have power reclining seatbacks. Use the vertical power seat control located on the outboard side of the seat. • To recline the seatback, press the control toward the rear of the vehicle. • To raise the seatback, press the control toward the front of the vehicle. 1-6[...]

{ CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts cannot do their job when you are reclined like this. The shoulder belt cannot do its job because it will not be against your body. Instead, it will be in front of you. In a crash, you could go into it, receiving neck o[...]

To raise a front seat head restraint, pull up on the restraint. To lower it, press the button, located on the top of the seatback, and push the head restraint down. To adjust the height of a rear seat head restraint, pull up or push down on the restraint. The front seat head restraints can also tilt forward and rearward. The rear seat head restrain[...]

Rear Seats Heated Seats Your vehicle may have heated rear seats. To operate the rear heated seats, the ignition must be on. The buttons are located on the rear doors. I (Heated Seatback): Press this button to turn on the heated seatback. J (Heated Seat and Seatback): Press this button to turn on the heated seat and seatback. Press a button to turn [...]

Power Lumbar Your vehicle may be equipped with four-way lumbar support, without the massage feature, for the outboard rear seat positions. The rear lumbar support controls are located on the rear doors in front of the heated seat buttons. To turn on the lumbar support feature, press the front of the control to increase support or rearward to decrea[...]

{ CAUTION: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and usin[...]

Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. Take the simplest vehicle. Suppose it is just a seat on wheels. Put someone on it. 1-12[...]

Get it up to speed. Then stop the vehicle. The rider does not stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield... 1-13[...]

or the instrument panel... or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. 1-14[...]

Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt? A: You could be — whether you are wearing a safety belt or not. But your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted. And you can unbuckle a safety[...]

How to Wear Safety Belts Properly This section is only for people of adult size. Be aware that there are special things to know about safety belts and children. And there are different rules for smaller children and babies. If a child will be riding in your vehicle, see Older Children on page 1-31 or Infants and Young Children on page 1-34 . Follow[...]

Q: What is wrong with this? A: The shoulder belt is too loose. It will not give nearly as much protection this way. { CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should fit snugly against your body. 1-17[...]

Q: What is wrong with this? A: The lap belt is too loose. It will not give as much protection this way. { CAUTION: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen. This could cause serious or even fatal injuries. The lap belt should be worn low and snug on the h[...]

Q: What is wrong with this? A: The belt is buckled in the wrong place. { CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones. This could cause serious internal injuries. Always buckle your belt into the[...]

Q: What is wrong with this? A: The belt is over an armrest. { CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries. Be s[...]

Q: What is wrong with this? A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. { CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury. Also, the belt would apply too much[...]

Q: What is wrong with this? A: The belt is behind the body. { CAUTION: You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury. You might also slide under the lap belt. The belt force w[...]

Q: What is wrong with this? A: The belt is twisted across the body. { CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer/retailer to fix it. 1-23[...]

Lap-Shoulder Belt All seating positions in your vehicle have a lap-shoulder except for the center front passenger position (if equipped), which has a lap belt. See Lap Belt on page 1-29 for more information. Here is how to wear a lap-shoulder belt properly. 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. To see how, see ?[...]

4. If equipped with a shoulder belt height adjuster, move it to the height that is right for you. Improper shoulder belt height adjustment could reduce the effectiveness of the safety belt in a crash. See “Shoulder Belt Height Adjustment” later in this section. 5. To make the lap part tight, pull up on the shoulder belt. It may be necessary to [...]

Shoulder Belt Height Adjuster Your vehicle has shoulder belt height adjusters for the driver and right front passenger position. Adjust the height so that the shoulder portion of the belt is centered on your shoulder. The belt should be away from your face and neck, but not falling off your shoulder. Incorrect positioning of the shoulder belt can r[...]

There is one guide for each outside passenger position in the rear seat. Here is how to install a comfort guide to the safety belt: 1. Remove the guide from its storage pocket on the side of the seatback. 2. Slide the guide under and past the belt. The elastic cord must be under the belt. Then, place the guide over the belt, and insert the two edge[...]

{ CAUTION: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces. 4. Buckle, position, and release the safety belt as de[...]

Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. A pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible, below the rounding, throughout the pregnancy. The best [...]

To make the belt shorter, pull its free end as shown until the belt is snug. If the belt is not long enough, see Safety Belt Extender on page 1-30 . Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if necessary. If you find that the latch plate will not go fully into the buckle, see [...]

Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. The manufacturer’s instructions that come with the booster seat, state the weight and height limitations for that booster. Use a booster seat with a lap-shoulder belt until the child passes the below fit test: • Sit all the [...]

Q: What is the proper way to wear safety belts? A: An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should fit snugly below the hips, just touching the top of the thighs. This applies belt force to the child’s pelvic bone[...]

{ CAUTION: Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. In a crash, the child would not be restrained by the shoulder belt. The child might slide under the lap belt. The belt force would then be applied right on the abdomen. That could cause serious or fatal injuries. The [...]

Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age[...]

{ CAUTION: Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them. Young children and i[...]

Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height, and age but also whether or not the restraint will be compatible with the m[...]

{ CAUTION: The body structure of a young child is quite unlike that of an adult or older child, for whom the safety belts are designed. A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should. Instead, it may settle up around the child’s abdomen. In a crash, the bel[...]

A booster seat (C-D) is a child restraint designed to improve the fit of the vehicle’s safety belt system. A booster seat can also help a child to see out the window. Securing an Add-On Child Restraint in the Vehicle { CAUTION: A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle. Ma[...]

To help reduce the chance of injury, the child restraint must be secured in the vehicle. Child restraint systems must be secured in vehicle seats by lap belts or the lap belt portion of a lap-shoulder belt, or by the LATCH system. See Lower Anchors and Tethers for Children (LATCH) on page 1-41 for more information. A child can be endangered in a cr[...]

Where to Put the Restraint Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. We recommend that children and child restraints be secured in a rear seat, including: an infant or a child riding in a rear-facing child restraint; a child riding in a forward-facing child seat; an older child r[...]

{ CAUTION: A child in a child restraint in the center front seat can be badly injured or killed by the frontal airbags if they inflate. Never secure a child restraint in the center front seat. It is always better to secure a child restraint in a rear seat. Do not use child restraints in the center front seat position. When securing a child restrai[...]

Lower Anchors Lower anchors (A) are metal bars built into the vehicle. There are two lower anchors for each LATCH seating position that will accommodate a child restraint with lower attachments (B). Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top tet[...]

Your child restraint may have a single tether (A) or a dual tether (C). Either will have a single attachment (B) to secure the top tether to the anchor. Some child restraints that have top tethers are designed for use with or without the top tether being attached. Others require the top tether always to be attached. In Canada, the law requires that[...]

To assist you in locating the top tether anchors, the top tether anchor symbol is located on the cover. The top tether anchors are located under the covers on the rear seatback filler panel. Pull open the cover to access the anchors. Be sure to use an anchor located on the same side of the vehicle as the seating position where the child restraint [...]

Securing a Child Restraint Designed for the LATCH System { CAUTION: If a LATCH-type child restraint is not attached to anchors, the restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed. Make sure that a LATCH-type child restraint is properly installed using the anchors, or use the veh[...]

{ CAUTION: Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Secure any unused safety belts behind the child restraint so children cannot reach them. Pull the shoulder belt all the way out of the retractor to set the lock, if your vehicle has one, after the child[...]

2. If the child restraint manufacturer recommends that the top tether be attached, attach and tighten the top tether to the top tether anchor, if equipped. Refer to the child restraint instructions and the following steps: 2.1. Find the top tether anchor. 2.2. Pull open the top tether anchor cover to expose the anchor. 2.3. If you have an adjustabl[...]

Securing a Child Restraint in a Rear Seat Position When securing a child restraint in a rear seating position, study the instructions that came with your child restraint to make sure it is compatible with this vehicle. If your child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH) on page 1-41 for how to install yo[...]

4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt, and feed the shoulder belt back into the retractor. If you are using a forward-facing child restraint, you may find it helpfu[...]

6. If your child restraint has a top tether, follow the child restraint manufacturer’s instructions regarding the use of the top tether. See Lower Anchors and Tethers for Children (LATCH) on page 1-41 for more information. 7. Push and pull the child restraint in dif ferent directions to be sure it is secure. To remove the child restraint, unbuckl[...]

{ CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag. Even though the passenger sensing system is designed to turn off the right front passenger’s frontal air[...]

3. Pick up the latch plate, and run the lap and shoulder portions of the vehicle’s safety belt through or around the restraint. The child restraint instructions will show you how. 4. Push the latch plate into the buckle until it clicks. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if necessar[...]

6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. If you are using a forward-facing child restraint, you may find it helpful to use your knee to push down on the child restraint as you tighten the belt. 7. Push a[...]

Airbag System Your vehicle has the following airbags: • A frontal airbag for the driver. • A frontal airbag for the right front passenger. • A seat-mounted side impact airbag for the driver. • A seat-mounted side impact airbag for the right front passenger. Your vehicle may also have the following airbags: • A roof-rail airbag for the dri[...]

{ CAUTION: Frontal airbags are designed to deploy in moderate to severe frontal and near frontal crashes. They are not designed to inflate in rollover, rear crashes, or in many side crashes. Seat-mounted side impact airbags and roof-rail airbags are designed to inflate in moderate to severe crashes where something hits the side of your vehicle. T[...]

{ CAUTION: Airbags plus lap-shoulder belts offer the best protection for adults, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them. Young children and infants need the protection that a child restraint system can provide. Always secure children properly in your vehicle. To [...]

The right front passenger’s frontal airbag is in the instrument panel on the passenger’s side. The seat-mounted side impact airbags for the driver and right front passenger are in the side of the seatbacks closest to the door. Driver Side shown, Passenger Side similar 1-57[...]

If your vehicle has roof-rail airbags for the driver, right front passenger, and second row outboard passengers, they are in the ceiling above the side windows. { CAUTION: If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into that person causing severe injury or even death. The p[...]

When Should an Airbag Inflate? Frontal airbags are designed to inflate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver’s or right front passenger’s head and chest. However, they are only designed to inflate if the impact exceeds a predetermined deployment threshold. [...]

Your vehicle has seat-mounted side impact airbags. Your vehicle may have roof-rail airbags. See Airbag System on page 1-54 . Seat-mounted side impact and roof-rail airbags are intended to inflate in moderate to severe side crashes. Seat-mounted side impact and roof-rail airbags will inflate if the crash severity is above the system’s designed t[...]

But airbags would not help in many types of collisions, primarily because the occupant’s motion is not toward those airbags. See When Should an Airbag Inflate? on page 1-59 for more information. Airbags should never be regarded as anything more than a supplement to safety belts. What Will You See After an Airbag Inflates? After the frontal airb[...]

In many crashes severe enough to inflate the airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. • Airbags are designed to inflate only once. After an airbag inflates, you will need some new parts for the airbag system. If you do not get them, the airbag sy[...]

The passenger sensing system will turn off the right front passenger’s frontal airbag and seat-mounted side impact airbag under certain conditions. The driver’s airbags are not part of the passenger sensing system. The passenger sensing system works with sensors that are part of the right front passenger’s seat and safety belt. The sensors ar[...]

The passenger sensing system is designed to turn off the right front passenger’s frontal airbag and seat-mounted side impact airbag if: • The right front passenger seat is unoccupied. • The system determines that an infant is present in a rear-facing infant seat. • The system determines that a small child is present in a child restraint. ?[...]

The passenger sensing system is designed to enable (may inflate) the right front passenger’s frontal airbag and seat-mounted side impact airbag anytime the system senses that a person of adult size is sitting properly in the right front passenger’s seat. When the passenger sensing system has allowed the airbags to be enabled, the on indicator [...]

Safety belts help keep the passenger in position on the seat during vehicle maneuvers and braking, which helps the passenger sensing system maintain the passenger airbag status. See “Safety Belts” and “Child Restraints” in the Index for additional information about the importance of proper restraint use. If you ever pull the shoulder portio[...]

A thick layer of additional material, such as a blanket or cushion, or aftermarket equipment such as seat covers, seat heaters, and seat massagers can affect how well the passenger sensing system operates. We recommend that you not use seat covers or other aftermarket equipment other than any that GM has approved for your specific vehicle. See Add[...]

Adding Equipment to Your Airbag-Equipped Vehicle Q: Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? A: Yes. If you add things that change your vehicle’s frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly. Changing or mov[...]

Restraint System Check Checking the Restraint Systems Safety Belts Now and then, make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job[...]

Replacing Restraint System Parts After a Crash { CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any ne[...]

Keys .............................................................. .2-3 Remote Keyless Entry (RKE) System ............... .2-4 Remote Keyless Entry (RKE) System Operation .................................................. .2-5 Remote Vehicle Start ..................................... .2-8 Doors and Locks ..........................................[...]

Park Tilt Mirrors ........................................... .2-42 Outside Convex Mirror .................................. .2-43 Outside Heated Mirrors ................................. .2-43 Object Detection Systems .............................. .2-44 Ultrasonic Front and Rear Parking Assist (UFRPA) ........................................ .2-4[...]

Keys { CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and they could be seriously injured or killed if ca[...]

Remote Keyless Entry (RKE) System Your Remote Keyless Entry (RKE) system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device [...]

Remote Keyless Entry (RKE) System Operation The Remote Keyless Entry (RKE) transmitter functions, including lock, unlock, remote trunk release, vehicle locator/panic alarm and remote vehicle start, if your vehicle has this feature, will work up to 195 feet (60 m) away. If your vehicle has the remote vehicle start feature, you will be able start you[...]

Q (Lock): Press the lock button to lock all the doors. If enabled through the Driver Information Center (DIC), the parking lamps may flash once to indicate locking has occurred, or the horn may chirp when the lock button is pressed again within five seconds from the previous press of the lock button. See DIC Vehicle Customization on page 3-86 for[...]

Battery Replacement Under normal use, the battery in your RKE transmitter should last about four years. The battery is weak if the transmitter will not work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it is probably time to change the battery. The REPLACE BATTERY IN REMOTE KEY message [...]

Remote Vehicle Start The remote vehicle starting feature allows you to start the engine from outside of the vehicle. It also starts up the vehicle’s automatic climate control system. When the remote start system is active, the climate control system will heat and cool the inside of the vehicle according to the previous settings of the system befo[...]

If the vehicle is left running it will automatically shut off after 10 minutes unless a time extension has been done. To manually shut off a remote start: • Aim the RKE transmitter at the vehicle and press the remote start button until the parking lamps turn off. • Turn on the hazard warning flashers. • Turn the ignition switch on and then o[...]

Doors and Locks Door Locks { CAUTION: Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked. So, wear safety belts properly [...]

Programmable Automatic Door Locks Your vehicle is programmed so that, when the doors are closed, the ignition is on, and the shift lever is moved out of PARK (P), all the doors will lock. The doors will unlock every time you stop the vehicle and move the shift lever into PARK (P). If someone needs to get out while your vehicle is not in PARK (P), h[...]

The rear doors on your vehicle cannot be opened from the inside when this feature is in use. When you want to open a rear door when the security lock is on, do the following: 1. Unlock the door using the remote keyless entry transmitter, the front door power lock switch, or by lifting the rear door manual lock knob. 2. Open the door from the outsid[...]

Remote Trunk Release G (Remote Trunk Release): The remote trunk release button is located to the left of the steering wheel next to the instrument panel brightness control. Press the button to open the trunk. To use this feature, your vehicle must be in PARK (P) or NEUTRAL (N) and the valet lockout switch must be off. You can also press the button [...]

Rear Seat Pass-Through Your vehicle has a small door in the rear seat. This door allows you to access the trunk from inside the vehicle. The rear seat armrest must be down for the pass-through door to open. To release the pass-through door, move the release up with your fingers. To close the door, raise it and push it until it latches. Windows { C[...]

Power Windows { CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome from extreme heat in warm or hot weather and suffer permanent injuries or even death from heat stroke. Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could[...]

Express-Down Window This feature is on all windows. Press the switch to the second position and release the switch to activate the express-down feature. To stop the window as it is lowering, press down or pull up briefly on the switch again. Express-Up Window This feature is on the front windows. Pull the switch up to the second position and relea[...]

Express Window Anti-Pinch Override { CAUTION: If express override is activated, the window will not reverse automatically. You or others could be injured and the window could be damaged. Before you use express override, make sure that all people and obstructions are clear of the window path. In an emergency, the anti-pinch feature can be overridden[...]

Rear Power Sunshade If your vehicle has a rear power sunshade, it helps to reduce the amount of heat and light entering the rear window. The switch is located on the overhead console. The rear power sunshade is located in the rear shelf. It only works while the ignition is on or while the Retained Accessory Power (RAP) is active. See Retained Acces[...]

— (On): Press this side of the button to turn the lockout feature on. When the lockout feature is turned on, the trunk cannot be unlocked with the keyless entry transmitter or the trunk release button located near the headlamp switch on the instrument panel. If the valet lockout feature is on it will also disable the Universal Home Remote transmi[...]

If you activate the alarm by accident, unlock the driver’s door with your key. You can also turn off the alarm by using the unlock button on the RKE transmitter system, or by starting the car with a valid key. Changes or modifications made to this system by other than an authorized service facility could void authorization to use the theft syste[...]

PASS-Key ® III+ Operation Your vehicle has PASS-Key ® III+ (Personalized Automotive Security System) theft-deterrent system. PASS-Key ® III+ is a passive theft-deterrent system. The system is automatically armed when the key is removed from the ignition. The system is automatically disarmed when the key is turned to ON/RUN, ACC/ACCESSORY or STAR[...]

To program the new key: 1. Verify that the new key has a 1 stamped on it. 2. Insert the original, already programmed, key in the ignition and start the engine. If the engine will not start, see your dealer/retailer for service. 3. After the engine has started, turn the key to LOCK/OFF, and remove the key. 4. Insert the new key to be programmed and [...]

Ignition Positions With the ignition key in the ignition, the key can be turned to four different positions: In order to shift out of PARK (P), ignition must be in the ON/RUN or ACC/ACCESSORY and the regular brake pedal must be applied. Notice: Using a tool to force the key from the ignition switch could cause damage or break the key. Use the corre[...]

Key In the Ignition Never leave your vehicle with the keys inside, as it is an easy target for joy riders or thieves. If you leave the key in the ignition and park your vehicle, a chime will sound, when you open the driver’s door. Always remember to remove your key from the ignition and take it with you. This will lock your ignition and transmiss[...]

Starting Procedure 1. With your foot of f the accelerator pedal, turn the ignition key to START. When the engine starts, let go of the key. The idle speed will go down as your engine gets warm. Do not race the engine immediately after starting it. Operate the engine and transmission gently to allow the oil to warm up and lubricate all moving parts.[...]

Engine Coolant Heater The engine coolant heater, if available, can help in cold weather conditions at or below 0°F ( − 18°C) for easier starting and better fuel economy during engine warm-up. Plug in the coolant heater at least four hours before starting your vehicle. To Use the Engine Coolant Heater 1. Turn of f the engine. 2. Open the hood an[...]

Automatic Transmission Operation The automatic transmission may have a shift lever located either on the steering column or on the console between the seats. There are several different positions for the shift lever. PARK (P): This position locks the front wheels. It is the best position to use when you start the engine because your vehicle cannot [...]

REVERSE (R): Use this gear to back up. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transmission. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped. Also use this gear to rock your vehicle back and forth to get out of snow, ice or sand without damaging[...]

DRIVE (D) can be used for towing. You may want to shift the transmission to THIRD (3) or, if necessary, to a lower gear if the transmission shifts too often under heavy loads and/or hilly conditions. See Towing a Trailer on page 4-27 for more information. THIRD (3): This position is also used for normal driving. However, it reduces vehicle speed mo[...]

Parking Brake The parking brake pedal is located to the left of the regular brake pedal, near the driver’s door. To set the parking brake, hold the regular brake pedal down with your right foot and push the parking brake pedal down with your left foot. If the ignition is on, the brake system warning light on the instrument panel cluster should co[...]

Shifting Into PARK (P) { CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly[...]

Leaving Your Vehicle With the Engine Running { CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake firmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch fire. You or others could[...]

Shifting Out of PARK (P) Automatic Transmission Shift Lock This vehicle has an electronic shift lock release system. The shift lock release is designed to: • Prevent ignition key removal unless the shift lever is in PARK (P) • Prevent movement of the shift lever out of PARK (P), unless the ignition is in ON/RUN or ACC/ACCESSORY and the regular [...]

Parking Over Things That Burn { CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. Engine Exhaust { CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness[...]

Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. { CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under Engine Exhaust on page 2-34 . Also, idling in a closed-in place can l[...]

Mirrors Automatic Dimming Rearview Mirror with Intellibeam™, OnStar ® , and Compass Your vehicle may have an automatic dimming rearview mirror with OnStar ® and a compass display. For more information, see OnStar ® System on page 2-53 . For more information on Intellibeam™, see “Intellibeam Intelligent High-Beam Headlamp Control System” [...]

Compass Variance The mirror is set to zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if the vehicle is driven outside zone eight. Under certain circumstances, such as a long distance, cross-country trip, it will be necessary to adjust the compass variance. Compass variance is the d[...]

Cleaning the Mirror When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing. Automatic Dimming Rearview Mirror with OnStar ® and Compass Your vehicle may have an automatic dimming rearview mirror w[...]

Compass Variance The zone is set to zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if you live outside zone eight. Under certain circumstances, as during a long distance cross-country trip, it will be necessary to adjust for compass variance. Compass variance is the difference betw[...]

Cleaning the Mirror When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing. Automatic Dimming Rearview Mirror with Compass Your vehicle may have an automatic dimming rearview mirror with a compass [...]

Outside Power Foldaway Mirrors Your vehicle’s mirror controls are located on the driver’s door armrest. • Press (A) to select the driver’s side mirror. Then press the arrows located on the four-way control pad to adjust the mirror. • Press (B) to select the passenger’s side mirror. Then press the arrows located on the four-way control p[...]

Resetting the Power Foldaway Mirrors You will need to reset the power foldaway mirrors if the following occurs: • They are accidentally manually folded/unfolded. • The mirrors will not stay in the unfolded position. • The mirrors shake and flutter at normal driving speeds. To reset the power foldaway mirrors, fold and unfold them three times[...]

Outside Convex Mirror { CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes. The passenger side mirror is convex. A convex mirror’s surfac[...]

Object Detection Systems Ultrasonic Front and Rear Parking Assist (UFRPA) If your vehicle has the Ultrasonic Front and Rear Parking Assist (UFRPA) system, it helps you park easier and helps you avoid colliding with objects such as parked vehicles. It operates at speeds less than 5 mph (8 km/h). It can determine how close objects are to the front bu[...]

The front display is located on top of the instrument panel to the right of the driver. The front display will have either three or six lights to provide distance and system information. With Adaptive Cruise control (ACC), it will have three lights along with the ACC lights. Without ACC, it will have six lights. High-toned beeps from the front spea[...]

Moving Forward When the vehicle is started, the front display will briefly illuminate to let you know the system is working. The following describes what will occur with the front display as you get closer to a object detected in the front of your vehicle: Description English Metric amber/amber lights ACC — one amber light 4 ft 1.2 m four amber [...]

When the System Does Not Seem to Work Properly • The driver disables the system. • The parking brake pedal is depressed. • The ultrasonic sensors are not kept clean. So be sure to keep your vehicle’s front and rear bumpers free of mud, dirt, snow, ice and slush. For cleaning instructions, see Washing Your Vehicle on page 5-90 . • A traile[...]

This indicates that it may be unsafe for you to change lanes. Before making a lane change, always check the SBZA display, check the outside and rearview mirrors, look over your shoulder for vehicles and hazards, and start the turn signal. SBZA Detection Zones The SBZA sensor covers a zone of approximately one lane over from both sides of the vehicl[...]

How the System Works When the vehicle is started, both outside mirror displays will briefly come on to indicate that the system is operating. When you are driving forward, the left or right side mirror SBZA display will light up if a vehicle is detected in that blind zone. If you activate a turn signal and a vehicle has been detected on the same s[...]

SBZA Error Messages The following messages may appear in the DIC: SIDE BLIND ZONE ALERT SYSTEM OFF: This message indicates that the driver has turned the system off. CLEAN SIDE BLIND ZONE ALERT SYSTEM: This message indicates that the SBZA system is disabled because the sensor is blocked and cannot detect vehicles in your blind zone. The sensor may [...]

CAUTION: (Continued) LDW will indicate the system is working whenever it detects either the left or right lane marking. So if you depart on the side of the lane that LDW is not detecting, LDW will not warn you. If you do not carefully maintain your vehicle position within the lane, vehicle damage, injury, or death could occur. Even with LDW, always[...]

If the LDW symbol does not appear, LDW is not currently operating and will not warn you. If you would like to change the volume of the warning chime, see Chime Volume under DIC Vehicle Customization on page 3-86 for more information. When the System Does Not Seem To Work Properly The LDW symbol will not appear when the system is having diff iculty [...]

OnStar ® System OnStar uses several innovative technologies and live advisors to provide you with a wide range of safety, security, information, and convenience services. If your airbags deploy, the system is designed to make an automatic call to OnStar Emergency advisors who can request emergency services be sent to your location. If you lock you[...]

Available Services with Safe & Sound Plan • Automatic Notification of Airbag Deployment • Advanced Automatic Crash Notification (AACN) (If equipped) • Link to Emergency Services • Roadside Assistance • Stolen Vehicle Location Assistance • AccidentAssist • Remote Door Unlock/Vehicle Alert • OnStar Vehicle Diagnostics • GM Goo[...]

OnStar Steering Wheel Controls Your vehicle may have a Talk/Mute button that can be used to interact with OnStar Hands-Free Calling. See Audio Steering Wheel Controls on page 3-117 for more information. On some vehicles, you may have to hold the button for a few seconds and give the command “ONSTAR” to activate the OnStar Hands-Free Calling. On[...]

Universal Home Remote System The Universal Home Remote System provides a way to replace up to three hand-held Radio-Frequency (RF) transmitters used to activate devices such as garage door openers, security systems, and home lighting. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This d[...]

Be sure to keep the original remote control transmitter for use in other vehicles, as well as, for future programming. You only need the original remote control transmitter for Fixed Code programming. It is also recommended that upon the sale or lease termination of the vehicle, the programmed buttons should be erased for security purposes. See “[...]

2. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. It can usually be found where the hanging antenna wire is attached to the motor-head unit and may be a colored button. Press this button. After you press this button, you will have 30 seconds to complete the following steps. 3. [...]

Programming Universal Home Remote — Fixed Code If you have questions or need help programming the Universal Home Remote System, call 1-866-572-2728 or go to www.learcar2u.com. Most garage door openers sold before 1996 are Fixed Code units. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before you be[...]

Your garage door opener receiver (motor head unit) may also have a row of dip switches that can be used when programming the Universal Home Remote. If the total number of switches on the motor head and hand held transmitter are different, or if the dip switch settings are different, use the dip switch settings on the motor head unit to program your[...]

2. Write down the eight to 12 switch settings from left to right as follows: • When a switch is in the up position, write “Left.” • When a switch is in the down position, write “Right.” • If a switch is set between the up and down position, write “Middle.” The switch settings that you wrote down in Step 2 will now become the butto[...]

5. After entering all of the switch positions, again, firmly press and release all three buttons at the same time. The indicator lights will turn on. 6. Press and hold the button you would like to use to control the garage door until the garage door moves. The indicator light above the selected button should slowly blink. You may need to hold the [...]

Storage Areas Glove Box To open, lift the handle up. Use the key to lock and unlock. Cupholder(s) There are cupholders located in the full floor console, or in the front of the center seat console. Cupholders are also located in the rear armrest. To access the full floor console cupholder slide the cover back. To access the center seat console cu[...]

Center Flex Storage Unit Your vehicle may have a center flex storage unit that includes a front center seat with a lap belt and an underseat storage compartment. The center seatback can also be used as a fold down armrest. Cupholders are also located at the front edge of the storage unit and can be accessed by folding the compartment forward. When[...]

Sunroof The vehicle may have a power sunroof. The switches that operate the sunroof are located on the overhead console. To open or close the sunroof, the ignition must be turned to ON/RUN or Retained Accessory Power (RAP) must be active. See Retained Accessory Power (RAP) on page 2-24 . Express Open: The express open feature will operate from the [...]

✍ NOTES 2-66[...]

Instrument Panel Overview .............................. .3-4 Hazard Warning Flashers ............................... .3-6 Other Warning Devices .................................. .3-6 Horn ............................................................ .3-6 Tilt Wheel .................................................... .3-6 Power Tilt Wheel and Tele[...]

Warning Lights, Gages, and Indicators ........... .3-51 Instrument Panel Cluster ............................... .3-52 Speedometer and Odometer .......................... .3-53 Tachometer ................................................ .3-53 Safety Belt Reminders .................................. .3-54 Airbag Readiness Light .....................[...]

✍ NOTES 3-3[...]

Instrument Panel Overview Console-Shift Model shown, Column-Shift Model similar 3-4[...]

The main components of the instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 3-46 . B. Driver Information Center (DIC) Buttons. See Driver Information Center (DIC) on page 3-68 . C. Exterior Lamp Controls. See Exterior Lamps on page 3-30 . D. Instrument Panel Cluster. See Instrument Panel Cluster on page 3-52 . E. Ho[...]

Hazard Warning Flashers The hazard warning flashers let you warn the police and others that you have a problem. The front and rear turn signal lamps will flash on and off. The hazard warning flasher button is located towards the center of the instrument panel. Press the button to make the front and rear turn signal lamps flash on and off. Press[...]

Power Tilt Wheel and Telescopic Steering Column If your vehicle has this feature, the power tilt and telescope wheel control is located on the outboard side of the steering column. To operate the power tilt feature, push the control up and the steering wheel tilts up. Push the control down and the steering wheel goes down. Push the control forward [...]

Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: • G Turn and Lane-Change Signals. See Turn and Lane-Change Signals on page 3-8 . • 23 Headlamp High/Low-Beam Changer. See Headlamp High/Low-Beam Changer on page 3-9 . • Flash-To-Pass Feature. See Flash-to-Pass on page 3-13 . • N Windshi[...]

Arrows that flash rapidly when signaling for a turn or lane change may be caused by a burned out signal bulb. Other drivers will not see the turn signal. Replace burned-out bulbs to help avoid possible accidents. Check the fuse and for burned-out bulbs if the arrow fails to work when signaling a turn. See Rear Underseat Fuse Block on page 5-100 . [...]

The Forward Collision Alert (FCA) system provides an audible and visual alert if you approach a vehicle too quickly that is directly ahead. FCA also provides a visual alert with no audible alert if you are following another vehicle much too closely. The FCA alert symbol is located on top of the instrument panel to the right of the driver. FCA uses [...]

{ CAUTION: • On winding roads, FCA may not detect a vehicle ahead. You could crash into a vehicle ahead of you. Do not rely on FCA on winding roads. • When weather limits visibility, such as in fog, rain, or snow, FCA performance is limited. There may not be enough warning distance to the vehicle in front of you. Do not rely on FCA in low visib[...]

Detecting the Vehicle Ahead The vehicle ahead symbol, located next to the FCA symbol, will only appear when a vehicle ahead of you is detected in your path. If this symbol does not appear, or disappears briefly, FCA will not respond to vehicles you may see ahead. The symbol may disappear on curves, highway exit ramps, or hills. Also, when another [...]

Cleaning the System The radar can become blocked by snow, ice, or dirt. If so, you may need to turn off the engine and clean the lens. See “Cleaning the System” under Adaptive Cruise Control on page 3-19 . Flash-to-Pass This feature lets you use the high-beam headlamps to signal the driver in front of you that you want to pass. The flash-to-pa[...]

Rainsense™ II Wipers If your vehicle has this feature, the moisture sensor is mounted on the interior side of the windshield behind the rearview mirror. It is used to automatically operate the wipers by monitoring the amount of moisture build-up on the windshield. Wipes occur as needed to clear the windshield depending on driving conditions and t[...]

Windshield Washer { CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision. J (Washer Fluid): Press and release this paddle, located at the top of the turn signal/multifunction lever, to spray washer fluid on the windshield. The wipers wi[...]

Cruise Control With cruise control, you can maintain a speed of approximately 25 mph (40 km/h) or more without keeping your foot on the accelerator. This is helpful on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h). When cruise control is on, you will see a cruise light on the instrument panel cluster. When you appl[...]

The cruise control buttons are located on left side of the steering wheel. I (On): This position turns on the system. + RES (Resume/Accelerate): Press this button to make the vehicle accelerate or resume to a previously set speed. SET– (Set): Press this button to set the speed. [ (Cancel): Press this button to cancel cruise control. Cruise contro[...]

Increasing Speed While Using Cruise Control There are two ways to go to a higher speed: • Use the accelerator pedal to get to the higher speed. Press the SET– button, then release the button and the accelerator pedal. The vehicle now cruises at the higher speed. • Press the +RES button. Hold it there until you get up to the desired speed, and[...]

Using Cruise Control on Hills How well your cruise control works on hills depends upon the vehicle speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle’s speed. When going downhill, you might have to brake or shift to a lower gear to keep the vehicle’s sp[...]

Adaptive Cruise Control is an enhancement to traditional cruise control. It allows you to keep cruise control engaged in moderate traff ic conditions without having to constantly reset your cruise control. Adaptive Cruise Control uses radar to detect a vehicle directly ahead in your path, within a distance of 330 ft (100 m), and operates at speeds [...]

CAUTION: (Continued) • Adaptive Cruise Control may not have time to slow your vehicle enough to avoid a crash when you are driving in conditions where vehicles may suddenly slow or stop ahead of you, enter your lane, or cross your vehicle’s path. If you are driving in these conditions, do not use Adaptive Cruise Control. The warning beep and al[...]

+GAP (Increase Following Distance): Press this button to increase the distance between your vehicle and other vehicles. − GAP (Decrease Following Distance): Press this button to decrease the distance between your vehicle and other vehicles. Adaptive cruise control will not work if the master cylinder brake fluid level is low. Engaging Adaptive C[...]

Increasing Set Speed While Using Adaptive Cruise Control There are two ways to increase the set speed: • Use the accelerator to get to the higher speed. Press the SET– button and then release the button and the accelerator pedal. The vehicle will now cruise at the higher speed. • Press the +RES button. Hold it there until the desired set spee[...]

There are six follow distances to choose from. The follow distance selection ranges from near to far (one second to two seconds follow time). The distance maintained for a selected follow distance will vary based on vehicle speed. The faster the vehicle speed the further back your vehicle will follow. Consider traff ic and weather conditions when s[...]

Approaching and Following a Vehicle The Vehicle Ahead symbol is located on the top of the instrument panel to the right of the driver. The Vehicle Ahead symbol only appears when a vehicle is detected in your path. If this symbol does not appear, or disappears briefly, Adaptive Cruise Control will not respond to vehicles you may see ahead. { CAUTIO[...]

Stationary or Very Slow-Moving Objects { CAUTION: Adaptive Cruise Control may not detect and react to stationary or slow-moving vehicles or other objects ahead of you. You could crash into an object ahead of you. Do not use Adaptive Cruise Control when approaching stationary or slow-moving vehicles or other objects. { CAUTION: Adaptive Cruise Contr[...]

{ CAUTION: If you rest your foot on the accelerator pedal, the system will not automatically apply the brakes. You could crash into a vehicle ahead of you. Do not rest your foot on the accelerator pedal when using Adaptive Cruise Control. Curves in the Road { CAUTION: Due to Adaptive Cruise Control limitations in curves, it may respond to a vehicle[...]

Adaptive Cruise Control may detect a vehicle that is not in your lane and apply the brakes. Adaptive Cruise Control may, occasionally, provide a driver alert and/or braking that you consider unnecessary. It could respond to signs, guardrails, and other stationary objects when entering or exiting a curve. This is normal operation. Your vehicle does [...]

Using Adaptive Cruise Control on Hills and When Towing a Trailer How well Adaptive Cruise Control will work on hills and when towing a trailer depends on your vehicle’s speed, vehicle load, traff ic conditions and the steepness of the hills. It may not detect a vehicle in your lane while driving on hills. When going up steep hills, you may want t[...]

Exterior Lamps The exterior lamps control is located on the instrument panel to the left of the steering wheel. It controls the following systems: • Headlamps • Taillamps • Parking Lamps • License Plate Lamps • Instrument Panel Lights • Fog Lamps The exterior lamps control has four positions: O (Off): This position turns of f the exteri[...]

IntelliBeam™ Intelligent High-Beam Headlamp Control System If your vehicle has this feature, be sure to read this entire section before using it. IntelliBeam™ is an enhancement to the vehicle’s headlamp system. Using a digital light sensor on the rearview mirror, this system turns the vehicle’s high-beam headlamps on and off according to su[...]

• The exterior lamp control is turned to any setting except AUTO. When this occurs, IntelliBeam™ is disabled until the control is turned back to the AUTO position. • The IntelliBeam™ system is turned off at the inside rearview mirror. IntelliBeam™ might not turn off the high-beams if the system cannot detect other vehicle’s lamps becaus[...]

Cleaning the IntelliBeam™ Light Sensor The light sensor is located on the inside of the vehicle in front of the inside rearview mirror. Clean the light sensor window, periodically, using glass cleaner on a soft cloth. Gently wipe the sensor window. Do not spray glass cleaner directly on the surface of the sensor window. Wiper Activated Headlamps [...]

When DRL are on, no other exterior lamps such as the parking lamps, taillamps, etc. will be on when the DRL are being used. The instrument panel will not be lit up either. When automatic lighting is on and it is dark enough outside, the turn signal lamps turn off and normal low-beam headlamp operation occurs. When automatic lighting is on and it is[...]

Cornering Lamps The cornering lamps come on when the headlamps or parking lamps are on and you signal a turn with the multifunction lever. They provide more light for cornering. Exterior Lighting Battery Saver If the exterior lamp button has been left on, the exterior lamps will turn off about 10 minutes after the ignition is turned to LOCK/OFF and[...]

Entry Lighting This feature turns on the courtesy lamps and the backlighting for the door switches and the exterior lamp control when a door is opened or if the remote keyless entry transmitter unlock button is pressed. If activated due to the transmitter, the lighting remains active for about 40 seconds. Since the entry lighting system uses the li[...]

Battery Load Management The battery load management feature is designed to monitor the vehicle’s electrical load and determine when the battery is in a heavy discharge condition. During times of high electrical loading, the engine may idle at a higher revolutions per minute (rpm) setting than normal to make sure the battery charges. High electric[...]

EPM works to prevent excessive discharge of the battery. It does this by balancing the generator’s output and the vehicle’s electrical needs. It can increase engine idle speed to generate more power, whenever needed. It can temporarily reduce the power demands of some accessories. Normally, these actions occur in steps or levels, without being [...]

There are two accessory power outlets in the rear seat area located on the door armrests next to the ashtrays. There may be a small cap that must be removed to access the accessory power outlet. When not using the outlet be sure to cover it with the protective cap. The accessory power outlet can be used at any time. Notice: Leaving electrical equip[...]

Rear Ashtray The ashtrays are located on the door armrests. To use an ashtray, lift the lid. Analog Clock The analog clock is located on the instrument panel above the radio. The clock is not connected with any other vehicle system and runs by itself. To adjust the clock: 1. Locate the adjustment button directly below the clock face. 2. Push and ho[...]

Automatic Operation AUTO 9 (Automatic Fan): When this position is selected on the fan control, the system adjusts the fan speed. If the OnStar ® system is activated when this position is selected, the climate control fan speed will lower. AUTO (Automatic Mode): 1. Turn the fan control to the AUTO position. 2. Turn the mode control to the AUTO posi[...]

If the AUTO position is selected on the fan or mode control, the system automatically controls the air conditioning compressor. The A/C compressor will run automatically even at cool outside temperatures in order to dehumidify the air. The A/C indicator light is lit when the system is operating automatically, even at near freezing outside temperatu[...]

F (Vent): Turn the control to this mode to direct air to the instrument panel outlets. * (Bi-Level): Turn the control to this mode to direct approximately half of the air to the instrument panel outlets and most of the remaining air to the floor outlets. In automatic operation, cooler air is directed to the upper outlets and warmer air to the flo[...]

PASS (Passenger’s Climate Control): Press this button to turn the passenger’s climate control systems on or off. When the passenger’s climate control system is on, the passenger’s temperature setting is displayed. The temperature selected by the front passenger also controls the rear system air temperature unless the rear seat passengers se[...]

There is also an interior temperature sensor located next to the steering wheel that measures the temperature of the air inside your vehicle. There is also an exterior temperature sensor located behind the front grille. This sensor reads the outside air temperature and helps maintain the temperature inside the vehicle. Any cover on the front of the[...]

0 (Defrost): Turn the control to this mode to direct most of the air to the windshield and the side window outlets. In this mode, the system automatically turns off recirculation and runs the air conditioning compressor, unless the outside temperature is at or below freezing. Recirculation cannot be selected while in the defrost mode. Do not drive [...]

Rear Climate Control System If your vehicle has a rear climate control system, the rear seat passengers can adjust the direction of the airflow, fan speed and temperature for the rear seating area. This system also works with the main climate control system in the vehicle. The control panel for this system is located on the back of the center cons[...]

Automatic Operation «A ª (Fan): Press this button until AUTO appears on the display to place the system in automatic mode. When automatic operation is active, the system automatically controls the fan speed. If in auto fan mode, pressing the up arrow button will cancel automatic operation and places the system in manual mode. If in auto mode, pre[...]

The access panel for the passenger compartment air filter is located under the hood near the windshield, on the passenger’s side of the vehicle. To access the passenger compartment air filter, do the following: 1. Use a tool to gently pry the cover up. If your vehicle has tabs that allow you to unlatch the cover with your fingers, you will not[...]

2. Then, insert a tool behind the push pin located on the inboard side of the air filter compartment to carefully pry the pin out. 3. To remove the air filter, insert a tool between the air filter and the compartment wall on the outboard side of the vehicle. Then, push in to flatten the pin holding the air filter in place. Gently remove the ai[...]

Warning Lights, Gages, and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to your warning lights and gages could [...]

Instrument Panel Cluster The instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how fast you are going, how much fuel you are using and many of the other things you will need to know to drive safely and economically. United States version shown, Canada similar 3-52[...]

Speedometer and Odometer The speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). See “MPH (km)” under DIC Operation and Displays on page 3-69 for more information. The odometer mileage can be checked without the vehicle running. Your vehicle’s odometer works together with the driver information cen[...]

Safety Belt Reminders Safety Belt Reminder Light When the engine is started, a chime will come on for several seconds to remind people to fasten their safety belts, unless the driver’s safety belt is already buckled. The safety belt light will also come on and stay on for several seconds, then it will flash for several more. This chime and light[...]

Airbag Readiness Light There is an airbag readiness light on the instrument panel cluster, which shows the airbag symbol. The system checks the airbag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag modules, the wiring and the c[...]

Passenger Airbag Status Indicator Your vehicle has the passenger sensing system. Your overhead console has a passenger airbag status indicator. When you start the vehicle, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. Then, after several more seconds, the status ind[...]

{ CAUTION: Even though the passenger sensing system is designed to turn off the right front passenger’s frontal airbag and seat-mounted side impact airbag (if equipped) if the system detects a rear-facing child restraint, no system is fail-safe, and no one can guarantee that an airbag will not deploy under some unusual circumstance, even though i[...]

Charging System Light This light will come on briefly when you turn on the ignition, but the engine is not running, as a check to show you it is working. It should go out once the engine is running. If it stays on, or comes on while you are driving, you may have a problem with the charging system. A charging system Driver Information Center (DIC) [...]

When the ignition is on, the brake system warning light will also come on when you set your parking brake. The light will stay on if your parking brake does not release fully. If it stays on after your parking brake is fully released, it means you have a brake problem. If the light comes on while you are driving, pull off the road and stop carefull[...]

Traction Control System (TCS) Warning Light The traction control system warning light should come on briefly when the engine is started. If the warning light does not come on then, have it fixed so it will be ready to warn you if there is a problem. If it stays on, or comes on when you are driving, there may be a problem with your traction contro[...]

Lane Departure Warning Light Your vehicle may have the lane departure warning system. This light will come on green, briefly, when the vehicle is started to show that it is working. This light will also come on green if the system detects a left or right lane marking. This light will change to amber and flash and three beeps will sound if you cro[...]

Engine Coolant Temperature Gage This gage shows the engine coolant temperature. It indicates when the engine has warmed up and if the cooling system is operating properly. If the gage pointer moves into the shaded area, the engine coolant is too hot and the engine coolant temperature warning light will come on. See Engine Overheating on page 5-25 f[...]

Malfunction Indicator Lamp Check Engine Light A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It makes sure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. The check engine light comes on to[...]

If the Light is Flashing The following can prevent more serious damage to your vehicle: • Reduce vehicle speed. • Avoid hard accelerations. • Avoid steep uphill grades. • If you are towing a trailer, reduce the amount of cargo being hauled as soon as it is possible. If the light stops flashing and remains on steady, see “If the Light Is [...]

Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel. See Gasoline Octane on page 5-5 . Poor fuel quality causes the engine not to run as eff iciently as designed. You might notice this as stalling after start-up, stalling when you put the vehicle into gear, misfiring, hesitation on acceleration, or stumb[...]

Oil Pressure Light { CAUTION: Do not keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches fire. You or others could be burned. Check your oil as soon as possible and have your vehicle serviced. Notice: Lack of proper engine oil maintenance may damage the engine. The repairs would not be covered by your [...]

Lights On Reminder This light comes on whenever the parking lamps are on. See Exterior Lamps on page 3-30 for more information. Cruise Control Light This light comes on whenever you set your cruise control. The light will go out when the cruise control is turned off. See Cruise Control on page 3-16 and Adaptive Cruise Control on page 3-19 for more [...]

Fuel Gage The fuel gage shows approximately how much fuel is in the tank. It works only when the engine is on. If the fuel supply gets low, the FUEL LEVEL LOW message will appear in the Driver Information Center and a single chime will sound. See DIC Warnings and Messages on page 3-73 for more information. Here are a few concerns some owners have h[...]

DIC Operation and Displays The Driver Information Center (DIC) has different displays which can be accessed by pressing the DIC buttons located on the instrument panel, to the left of the steering wheel. 3 Trip/Fuel: Press this button to scroll through the trip and fuel displays. See “Trip/Fuel Display Menu Items” following for more information[...]

FUEL RANGE This display shows the approximate number of remaining miles (mi) or kilometers (km) you can drive without refilling the fuel tank. This estimate is based on the current driving conditions and will change if the driving conditions change. For example, if you are driving in traff ic and making frequent stops, the display may read one num[...]

AVERAGE SPEED This display shows the average speed of the vehicle in either miles per hour (mph) or kilometers per hour (km/h). This average is calculated based on the various vehicle speeds recorded since the last reset of this display. To reset this display, press the set/reset button. The display will return to zero. BATTERY VOLTAGE This display[...]

UNITS This display allows you to select between English or Metric units of measurement. Once in this display, press the set/reset button to select between ENGLISH or METRIC units. PARKING ASSIST If your vehicle has the Ultrasonic Front and Rear Parking Assist (UFRPA) system, this display allows the system to be turned on or off. Once in this displa[...]

If the tire pressure display shows dashes instead of a value, there may be a problem with your vehicle. If this consistently occurs, see your dealer/retailer for service. RELEARN REMOTE KEY This display allows you to match Remote Keyless Entry (RKE) transmitters to your vehicle. To match an RKE transmitter to your vehicle: 1. Press the vehicle info[...]

BATTERY SAVER ACTIVE This message displays when the system detects that the battery voltage is dropping beyond a reasonable level. The battery saver system starts reducing certain features of the vehicle that you may be able to notice. At the point that the features are disabled, this message is displayed. It means that the vehicle is trying to sav[...]

CLEAN SIDE BLIND ZONE ALERT SYSTEM If your vehicle has the Side Blind Zone Alert (SBZA) system, this message displays when the SBZA system is disabled because the sensor is blocked and cannot detect vehicles in your blind zone. The sensor may be blocked by mud, dirt, snow, ice, or slush. This message may also display during heavy rain or due to roa[...]

ENGINE OVERHEATED IDLE ENGINE Notice: If you drive your vehicle while the engine is overheating, severe engine damage may occur. If an overheat warning appears on the instrument panel cluster and/or DIC, stop the vehicle as soon as possible. Do not increase the engine speed above normal idling speed. See Engine Overheating on page 5-25 for more inf[...]

FOLLOWING GAP This symbol appears with this message. If your vehicle has Adaptive Cruise Control (ACC), this message displays to show the follow distance that has been set. There are six follow distances to choose from. Each follow distance is shown on the DIC by displaying from one to six bars between two car symbols. See Adaptive Cruise Control o[...]

HEATING WASH (Washer) FLUID WASH (Washer) WIPES PENDING This message displays when you turn on the heated washer fluid system. See “Heated Washer Fluid” under Windshield Washer on page 3-15 for more information. HOOD OPEN This symbol appears with this message. This message displays when the hood is not closed completely. Make sure that the hoo[...]

NO CRUISE BRAKING GAS PEDAL APPLIED This message displays when the Adaptive Cruise Control (ACC) is engaged and you are pressing the accelerator pedal enough to disable ACC automatic braking. See Adaptive Cruise Control on page 3-19 for more information. OIL PRESSURE LOW STOP ENGINE Notice: If you drive your vehicle while the engine oil pressure is[...]

RADAR CRUISE NOT READY This message displays when the Adaptive Cruise Control (ACC) system will not activate due to a temporary condition. Your vehicle does not require service. If this message appears when you attempt to activate the system, continue driving for several minutes and then try activating the system again. See Adaptive Cruise Control [...]

SERVICE AIR BAG This message displays when there is a problem with the airbag system. Have your vehicle serviced by your dealer/retailer immediately. See Airbag Readiness Light on page 3-55 for more information. SERVICE A/C SYSTEM This message displays when the air delivery mode door or the electronic sensors that control the air conditioning and h[...]

SERVICE PARKING ASSIST If your vehicle has the Ultrasonic Front and Rear Parking Assist (UFRPA) system, this message displays if there is a problem with the UFRPA system. Do not use this system to help you park. See Ultrasonic Front and Rear Parking Assist (UFRPA) on page 2-44 for more information. See your dealer/retailer for service. SERVICE POWE[...]

SERVICE SUSPENSION SYS (System) This message displays when the magnetic ride control or automatic leveling control system is not operating properly. Have your vehicle serviced by your dealer/retailer. SERVICE THEFT DETERRENT SYSTEM This message displays when there is a problem with the theft-deterrent system programmed in the key. A fault has been [...]

SIDE BLIND ZONE ALERT SYSTEM OFF If your vehicle has the Side Blind Zone Alert (SBZA) system, this message displays when the SBZA system has been turned off. See Side Blind Zone Alert on page 2-47 and DIC Operation and Displays on page 3-69 for more information. SPEED LIMITED TO XXX MPH (km/h) This message displays when your vehicle speed is limite[...]

TIRE LEARNING ACTIVE This message displays when the Tire Pressure Monitor System (TPMS) is re-learning the tire positions on your vehicle. The tire positions must be re-learned after rotating the tires or after replacing a tire or sensor. See Tire Inspection and Rotation on page 5-66 , Tire Pressure Monitor System on page 5-61 , and Inflation - Ti[...]

TURN SIGNAL ON This message displays as a reminder to turn off the turn signal if you drive your vehicle for more than about 1 mile (1.6 km) with a turn signal on. A multiple chime sounds when this message is displayed. WASHER FLUID LOW ADD FLUID This symbol appears with this message. This message displays when your vehicle is low on windshield was[...]

Entering the Feature Settings Menu 1. Turn the ignition on and place the vehicle in PARK (P). To avoid excessive drain on the battery, it is recommended that the headlamps are turned off. 2. Press the customization button to enter the feature settings menu. If the menu is not available, FEATURE SETTINGS AVAILABLE IN PARK will display. Before enteri[...]

AUTO DOOR LOCK This feature allows you to select when the vehicle’s doors will automatically lock. See Programmable Automatic Door Locks on page 2-11 for more information. Press the customization button until AUTO DOOR LOCK appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the menu up/[...]

REMOTE DOOR LOCK This feature allows you to select the type of feedback you will receive when locking the vehicle with the Remote Keyless Entry (RKE) transmitter. You will not receive feedback when locking the vehicle with the RKE transmitter if the doors are open. See Remote Keyless Entry (RKE) System Operation on page 2-5 for more information. Pr[...]

DELAY DOOR LOCK This feature allows you to select whether or not the locking of the vehicle’s doors will be delayed. When locking the doors with the power door lock switch and a door is open, this feature will delay locking the doors until five seconds after the last door is closed. You will hear three chimes to signal that the delayed locking f[...]

APPROACH LIGHTING This feature allows you to select whether or not to have the exterior lights turn on briefly during low light periods after unlocking the vehicle using the Remote Keyless Entry (RKE) transmitter. Press the customization button until APPROACH LIGHTING appears on the DIC display. Press the set/reset button once to access the settin[...]

PARK TILT MIRRORS If your vehicle has this feature, it allows you to select whether or not the outside mirror(s) will automatically tilt down when the vehicle is shifted into REVERSE (R). See Park Tilt Mirrors on page 2-42 for more information. Press the customization button until PARK TILT MIRRORS appears on the DIC display. Press the set/reset bu[...]

NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. EASY EXIT SETUP If your vehicle has this feature, it allows you to select which areas will recall with the automatic easy exit seat feature. It also allows you to turn[...]

MEMORY SEAT RECALL If your vehicle has this feature, it allows you to select your preference for the remote memory seat recall feature. See Memory Seat, Mirrors and Steering Wheel on page 1-4 for more information. Press the customization button until MEMORY SEAT RECALL appears on the DIC display. Press the set/reset button once to access the settin[...]

Press the customization button until FACTORY SETTINGS appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: RESTORE ALL (default): The customization features will be set to their factory default settings. DO NOT RESTORE: The c[...]

• Set up your audio system by presetting your favorite radio stations, setting the tone, and adjusting the speakers. Then, when driving conditions permit, you can tune to your favorite radio stations using the presets and steering wheel controls if the vehicle has them. Notice: Before adding any sound equipment to your vehicle, such as an audio s[...]

3. Press the pushbutton located under the forward arrow label until the menu for default clock and date settings appear. 4. Press the pushbutton located under the currently displayed status of either ON or OFF. The ON display indicates the radio clock display is disabled and the OFF display indicates the radio clock display is enabled. Press this p[...]

Setting the Time and Date For the Single CD Player This type of radio has a H (clock) button for setting the time and date. To set the time and date, do the following: 1. Turn the radio on. 2. Press the H button and HR, MIN, MM, DD, YYYY (hour, minute, month, day, and year) displays. 3. Press the pushbutton located under any one of the labels that [...]

Changing the Time and Date Default Setting For the Single CD Player To change the time and date default setting, do the following: 1. Change the time default setting from 12 hour to 24 hour or the date default setting from month/day/ year to day/month/year, by pressing the H (clock) button. 2. Once the clock and date settings display along with the[...]

Radio(s) (MP3) Radio Data System (RDS) The audio system has a Radio Data System (RDS). The RDS feature is available for use only on FM stations that broadcast RDS information. This system relies upon receiving specific information from these stations and only works when the information is available. While the radio is tuned to an FM-RDS station, t[...]

4. Press the pushbutton under the desired Speed Compensated Volume setting (OFF, Low, Med, or High) to select the level of radio volume compensation. The display times out after approximately 10 seconds. Each higher setting allows for more radio volume compensation at faster vehicle speeds. AudioPilot ® : If your vehicle has the Bose ® audio syst[...]

Storing a Radio Station as a Favorite Drivers are encouraged to set up their radio station favorites while the vehicle is in PARK (P). Tune to your favorite stations using the presets, favorites button, and steering wheel controls, if the vehicle has this feature. See Defensive Driving on page 4-2 . FAV (Favorites): A maximum of 36 stations can be [...]

Turn the a knob clockwise or counterclockwise to adjust the highlighted setting. The highlighted setting can also be adjusted by pressing either SEEK arrow, FWD (forward), or s REV (reverse) button until the desired levels are obtained. If a station’s frequency is weak or has static, decrease the treble. To quickly adjust bass, midrange, or tre[...]

To quickly adjust balance or fade to the middle position, press the pushbutton positioned under the BAL or FADE label for more than two seconds. A beep sounds and the level adjusts to the middle position. To quickly adjust all speaker and tone controls to the middle position, press the a knob for more than two seconds until a beep sounds. Digital S[...]

2. Press either of the two pushbuttons below the desired category label to immediately tune to the first XM™ (if equipped) station associated with that category. 3. Turn the a knob, press the pushbuttons below the displayed right or left arrows, or press either SEEK arrow to go to the previous or the next XM™ (if equipped) station within the s[...]

XM™ Satellite Radio Service XM™ is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces. XM™ Satellite Radio has a wide variety of programming and commercial-free music, coast-to-coast, and in digital-quality sound. During your trial or when you subscribe, you will get unlimited access to XM™ [...]

The use of CD lens cleaners for CDs is not advised, due to the risk of contaminating the lens of the CD optics with lubricants internal to the CD player mechanism. Notice: If a label is added to a CD, or more than one CD is inserted into the slot at a time, or an attempt is made to play scratched or damaged CDs, the CD player could be damaged. Whil[...]

s REV (Fast Reverse): Press and hold to reverse playback quickly within a track. You will hear sound at a reduced volume. Release to resume playing the track. The elapsed time of the track displays. FWD (Fast Forward): Press and hold to advance playback quickly within a track. You will hear sound at a reduced volume. Release to resume playing the[...]

CD Messages DISC ERROR: If this message displays and/or the CD ejects, it could be for one of the following reasons: • The radio system does not support the playlist format, the compressed audio format, or the data file format. • It is very hot. When the temperature returns to normal, the CD should play. • You are driving on a very rough roa[...]

BAND: Press to listen to the radio when a portable audio device is playing. The portable audio device continues playing, so you might want to stop it or power it off. CD/AUX (CD/Auxiliary): Press to play a CD when a portable audio device is playing. Press again and the system begins playing audio from the connected portable audio player. If a porta[...]

• Make sure playlists have a .mp3 or .wpl extension (other file extensions might not work). • Minimize the length of the file, folder or playlist names. Long file, folder, or playlist names, or a combination of a large number of files and folders, or playlists can cause the player to be unable to play up to the maximum number of files, fol[...]

Order of Play Tracks recorded to the CD-R or CD-RW play in the following order: • Play begins from the first track in the first playlist and continues sequentially through all tracks in each playlist. When the last track of the last playlist has played, play continues from the first track of the first playlist. − Playlists can be changed by[...]

Playing an MP3/WMA Insert a CD-R or CD-RW partway into the slot (Single CD Player), or press the load button and wait for the message to insert disc (Six-Disc CD Player), label side up. The player pulls it in, and the CD-R or CD-RW should begin playing. Z (Eject): Press this button to eject CD-R(s) or CD-RW(s). To eject the CD-R or CD-RW that is cu[...]

RDM (Random): With the random setting, MP3/WMA files on the CD-R can be played in random, rather than sequential order, on one CD-R/CD-RW or all discs in a six-disc CD player. To use random, do one of the following: 1. To play MP3/WMA files from the CD-R or CD-RW in random order, press the pushbutton positioned under the RDM label until Random Cu[...]

BAND: Press this button to listen to the radio when a CD is playing. The inactive CD remains inside the radio for future listening. CD/AUX (CD/Auxiliary): Press this button to play a CD when listening to the radio. The CD icon and a message showing disc and/or track number displays when a CD is in the player. Press this button again and the system [...]

XM TheftLocked: The XM™ receiver in the vehicle may have previously been in another vehicle. For security purposes, XM™ receivers cannot be swapped between vehicles. If this message appears after having your vehicle serviced, check with your dealer/retailer. XM Radio ID: If tuned to channel 0, this message alternates with the XM™ Radio eight [...]

Audio Steering Wheel Controls The audio steering wheel controls may be different depending on your vehicle’s options. Some audio controls can be adjusted at the steering wheel. They include the following: xw (Next/Previous): Press the down or up arrow to go to the next or to the previous radio station stored as a favorite. The radio has up to six[...]

¨ (Seek): Press the seek arrow to go to the next radio station and stay there. The system only seeks radio stations with strong frequencies. When the seek arrow is pressed and held for two seconds, the system scans the radio stations that are in the selected band. If listening to a CD, the system advances to the next CD when multiple discs are ins[...]

Backglass Antenna The AM-FM antenna is integrated with the rear window defogger, located in the rear window. Make sure that the inside surface of the rear window is not scratched and that the grid lines on the glass are not damaged. If the inside surface is damaged, it could interfere with radio reception. Notice: Using a razor blade or sharp objec[...]

✍ NOTES 3-120[...]

Your Driving, the Road, and Your Vehicle ......... .4-2 Defensive Driving .......................................... .4-2 Drunk Driving ................................................ .4-2 Control of a Vehicle ....................................... .4-3 Braking ........................................................ .4-3 Antilock Brake System (A[...]

Your Driving, the Road, and Your Vehicle Defensive Driving Defensive driving means “always expect the unexpected.” The first step in driving defensively is to wear your safety belt — See Safety Belts: They Are for Everyone on page 1-10 . { CAUTION: Assume that other road users (pedestrians, bicyclists, and other drivers) are going to be care[...]

For persons under 21, it is against the law in every U.S. state to drink alcohol. There are good medical, psychological, and developmental reasons for these laws. The obvious way to eliminate the leading highway safety problem is for people never to drink alcohol and then drive. Medical research shows that alcohol in a person’s system can make cr[...]

Avoid needless heavy braking. Some people drive in spurts — heavy acceleration followed by heavy braking — rather than keeping pace with traff ic. This is a mistake. The brakes might not have time to cool between hard stops. The brakes will wear out much faster if you do a lot of heavy braking. If you keep pace with the traff ic and allow reali[...]

ABS can change the brake pressure faster than any driver could. The computer is programmed to make the most of available tire and road conditions. This can help you steer around the obstacle while braking hard. As you brake, the computer keeps receiving updates on wheel speed and controls braking pressure accordingly. Remember: ABS does not change [...]

The traction control system automatically comes on whenever you start your vehicle. To limit wheel spin, especially in slippery road conditions, you should always leave the system on. But you can turn the traction control system off if you ever need to. You can turn the system on or off at any time by pressing the traction control system button loc[...]

StabiliTrak ® System Your vehicle may have this feature. The StabiliTrak ® system is an advanced computer controlled system that helps the driver maintain directional control of the vehicle in diff icult driving conditions. This is accomplished by selectively applying any one of the vehicle’s brakes and reducing engine power. The StabiliTrak ®[...]

Steering Power Steering If you lose power steering assist because the engine stops or the system is not functioning, you can steer but it will take much more effort. Magnetic Speed Variable Assist Steering System This system continuously adjusts the effort you feel when steering at all vehicle speeds. It provides ease when parking, yet a firm, sol[...]

Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and find a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you. You can avoid these problems by braking — if you can stop in ti[...]

Of f-Road Recovery You may find that your vehicle’s right wheels have dropped off the edge of a road onto the shoulder while you are driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that your vehicle straddles the[...]

Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible. The three types of skids correspond to your vehicle’s three control systems. In the braking skid, the wheels are not rolli[...]

Driving at Night Night driving is more dangerous than day driving because some drivers are likely to be impaired — by alcohol or drugs, with night vision problems, or by fatigue. Night driving tips include: • Drive defensively. • Do not drink and drive. • Reduce headlamp glare by adjusting the inside rearview mirror. • Slow down and keep [...]

Hydroplaning Hydroplaning is dangerous. Water can build up under your vehicle’s tires so they actually ride on the water. This can happen if the road is wet enough and you are going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road. There is no hard and fast rule about hydroplaning. The best advice is to sl[...]

Highway Hypnosis Always be alert and pay attention to your surroundings while driving. If you become tired or sleepy, find a safe place to park your vehicle and rest. Other driving tips include: • Keep the vehicle well ventilated. • Keep interior temperature cool. • Keep your eyes moving — scan the road ahead and to the sides. • Check th[...]

{ CAUTION: Coasting downhill in NEUTRAL (N) or with the ignition off is dangerous. The brakes will have to do all the work of slowing down and they could get so hot that they would not work well. You would then have poor braking or even none going down a hill. You could crash. Always have the engine running and your vehicle in gear when you go down[...]

Driving on Snow or Ice Most of the time, those places where the tires meet the road probably have good traction. However, if there is snow or ice between the tires and the road, you can have a very slippery situation. You have a lot less traction, or grip, and need to be very careful. What is the worst time for this? Wet ice. Very cold snow or ice [...]

The Antilock Brake System (ABS) improves your vehicle’s stability when you make a hard stop on a slippery road. Even though you have ABS, begin stopping sooner than you would on dry pavement. See Antilock Brake System (ABS) on page 4-4 . • Allow greater following distance on any slippery road. • Watch for slippery spots. The road might be fi[...]

You can run the engine to keep warm, but be careful. { CAUTION: Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You cannot see it or smell it, so you might not know it is in your vehicle. Clear away snow from around the base of your vehicle, especially[...]

Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine again and repeat this only when you feel really uncomfortable from the cold. But do it as little as possible. Preserve the fuel as long as you can. To help keep warm, you can get out of the vehicle and do some fairly vigorous exercises every hal[...]

Rocking Your Vehicle to Get It Out First, turn the steering wheel left and right to clear the area around the front wheels. Turn off any traction or stability system. See Traction Control System (TCS) on page 4-5 and StabiliTrak ® System on page 4-7 . Then shift back and forth between REVERSE (R) and a forward gear, spinning the wheels as little a[...]

Tire and Loading Information Label A vehicle specific Tire and Loading Information label is attached to the vehicle’s center pillar (B-pillar). With the driver’s door open, you will find the label attached below the door lock post (striker). The Tire and Loading Information label shows the number of occupant seating positions (A), and the max[...]

Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX [...]

Item Description Total A Vehicle Capacity Weight for Example 2 = 1,000 lbs (453 kg) B Subtract Occupant Weight 150 lbs (68 kg) × 5 = 750 lbs (340 kg) C Available Cargo Weight = 250 lbs (113 kg) Item Description Total A Vehicle Capacity Weight for Example 3 = 1,000 lbs (453 kg) B Subtract Occupant Weight 200 lbs (91 kg) × 5 = 1,000 lbs (453 kg) C [...]

Certification Label A vehicle specific Certification label is attached to the rear edge of the driver’s door. This label shows the gross weight capacity of your vehicle, called the Gross Vehicle Weight Rating (GVWR). The GVWR includes the weight of the vehicle, all occupants, fuel, and cargo. Never exceed the GVWR for your vehicle, or the Gros[...]

If you put things inside your vehicle, like suitcases, tools, packages, or anything else, they will go as fast as the vehicle goes. If you have to stop or turn quickly, or if there is a crash, they will keep going. { CAUTION: Things you put inside your vehicle can strike and injure people in a sudden stop or turn, or in a crash. • Put things in t[...]

Towing Towing Your Vehicle Consult your dealer/retailer or a professional towing service if you need to have your disabled vehicle towed. See Roadside Service on page 7-7 . If you want to tow your vehicle behind another vehicle for recreational purposes (such as behind a motorhome), see Recreational Vehicle Towing following. Recreational Vehicle To[...]

Dolly Towing Your vehicle can be towed using a dolly. To tow your vehicle using a dolly, follow these steps: 1. Put the front wheels on the dolly. 2. Put the vehicle in PARK (P). 3. Set the parking brake and then remove the key. 4. Clamp the steering wheel in a straight-ahead position. 5. Release the parking brake. Towing a Trailer The Cadillac Pro[...]

That is the reason for this part. In it are many time-tested, important trailering tips and safety rules. Many of these are important for your safety and that of your passengers. So please read this section carefully before you pull a trailer. Load-pulling components such as the engine, transmission, wheel assemblies and tires are forced to work ha[...]

Weight of the Trailer How heavy can a trailer safely be? It should never weigh more than 1,000 lbs (454 kg). These are total maximum weights including the load. But even that can be too heavy. It depends on how you plan to use your rig. For example, speed, altitude, road grades, outside temperature and how much your vehicle is used to pull a traile[...]

After you have loaded your trailer, weigh the trailer and then the tongue, separately, to see if the weights are proper. If they are not, you may be able to get them right simply by moving some items around in the trailer. Total Weight on Your Vehicle’s Tires Be sure your vehicle’s tires are inflated to the upper limit for cold tires. You will[...]

Driving with a Trailer Towing a trailer requires a certain amount of experience. Before setting out for the open road, you will want to get to know your rig. Acquaint yourself with the feel of handling and braking with the added weight of the trailer. And always keep in mind that the vehicle you are driving is now a good deal longer and not nearly [...]

Turn Signals When Towing a Trailer When you tow a trailer, your vehicle may need a different turn signal flasher and/or extra wiring. Check with your /retailer. The arrows on your instrument panel will flash whenever you signal a turn or lane change. Properly hooked up, the trailer lamps will also flash, telling other drivers you are about to tu[...]

When You Are Ready to Leave After Parking on a Hill 1. Apply your regular brakes and hold the pedal down while you: • Start your engine, • Shift into a gear, and • Make sure the parking brake has released. 2. Let up on the brake pedal. 3. Drive slowly until the trailer is clear of the chocks. 4. Stop and have someone pick up and store the cho[...]

✍ NOTES 4-34[...]

Service ........................................................... .5-3 Accessories and Modifications ......................... .5-3 California Proposition 65 Warning .................... .5-4 California Perchlorate Materials Requirements .... .5-4 Doing Your Own Service Work ........................ .5-4 Adding Equipment to the Outside of Your V[...]

Wheel Alignment and Tire Balance ................. .5-73 Wheel Replacement ..................................... .5-74 Tire Chains ................................................. .5-75 If a Tire Goes Flat ....................................... .5-76 Changing a Flat Tire .................................... .5-77 Removing the Spare Tire and Tools[...]

Service For service and parts needs, visit your dealer/retailer. You will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories and Modifications When non-dealer/non-retailer accessories are added to your vehicle they can affect your vehicle’s performance and safety, including[...]

California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems (including some inside the vehicle), many fluids, and some component wear by-products contain and/or emit thes[...]

If you want to do some of your own service work, you should use the proper service manual. It tells you much more about how to service your vehicle than this manual can. To order the proper service manual, see Service Publications Ordering Information on page 7-15 . Your vehicle has an airbag system. Before attempting to do your own service work, s[...]

Gasoline Specifications At a minimum, gasoline should meet ASTM specification D 4814 in the United States or CAN/CGSB-3.5 or 3.511 in Canada. Some gasolines contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT). We recommend against the use of gasolines containing MMT. See Additives on page 5-6 for additio[...]

Notice: Your vehicle was not designed for fuel that contains methanol. Do not use fuel containing methanol. It can corrode metal parts in the fuel system and also damage plastic and rubber parts. That damage would not be covered under your warranty. Some gasolines that are not reformulated for low emissions can contain an octane-enhancing additive [...]

Filling the Tank { CAUTION: Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle. Do not use cellular phones. Keep sparks, flames,[...]

To remove the fuel cap, turn it slowly counterclockwise. The fuel cap has a spring in it; if the cap is released too soon, it will spring back to the right. While refueling, hang the tethered fuel cap from the hook on the fuel door. { CAUTION: Fuel can spray out on you if you open the fuel cap too quickly. If you spill fuel and then something ignit[...]

Filling a Portable Fuel Container { CAUTION: Never fill a portable fuel container while it is in your vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned and your vehicle damaged if this occurs. To help avoid injury to you and others: • Dispense fuel only into approved containers. • Do no[...]

Hood Release To lift the hood, use the following steps: 1. Pull the hood release lever with this symbol on it. It is located on the lower left side of the instrument panel. 2. Then go to the front of the vehicle and find the secondary hood release lever, located near the center of the hood. Move the release lever up and to the right to raise the h[...]

Engine Compartment Overview When you open the hood, here is what you will see: 4.6L L37 Engine shown, 4.6L LD8 Engine similar 5-12[...]

A. Underhood Fuse Block. See Underhood Fuse Block on page 5-97 . B. Remote Positive (+) Terminal. See Jump Starting on page 5-40 . C. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-34 . D. Engine Coolant Surge Tank and Pressure Cap. See Coolant Surge Tank Pressure Cap on page 5-25 and Coolin[...]

When to Add Engine Oil If the oil is below the cross-hatched area at the tip of the dipstick, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Specifications on page 5-105 . Notice: Do not add too much oil. If the engine has so much oil that th[...]

What Kind of Engine Oil to Use Look for three things: • GM4718M Your vehicle’s engine requires a special oil meeting GM Standard GM4718M. Oils meeting this standard may be identified as synthetic. However, not all synthetic oils will meet this GM standard. Look for and use only an oil that meets GM Standard GM4718M. Notice: If you use oils tha[...]

Substitute Engine Oil: When adding oil to maintain engine oil level, oil meeting GM Standard GM4718M may not be available. You can add substitute oil designated SAE 5W-30 with the starburst symbol at all temperatures. Substitute oil not meeting GM Standard GM4718M should not be used for an oil change. Engine Oil Additives Do not add anything to the[...]

How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change the engine oil and filter based on vehicle use. Whenever the oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where you change the oil prior to a CHANGE ENGINE OIL SOON message in the Driver I[...]

Engine Air Cleaner/Filter See Engine Compartment Overview on page 5-12 for the location of the engine air cleaner/filter. When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/filter at the Maintenance II intervals and replace it at the first oil change after each 50,000 mile (80 000 km) interval. See Scheduled Maintenance on pag[...]

Follow these steps to reinstall the cover to the engine air cleaner/filter housing: 1. Align the two hinges located on the inboard side of the cover. 2. Push the cover slightly down and towards the engine to engage the tabs in the hinges and align the two screws. 3. Tighten the two screws on the top of the engine air cleaner/filter housing cover.[...]

How to Check Automatic Transmission Fluid Because this operation can be a little diff icult, you may choose to have this done at the dealer/retailer service department. If you do it yourself, be sure to follow all the instructions here, or you could get a false reading on the dipstick. Notice: Too much or too little fluid can damage your transmiss[...]

3. Check both sides of the dipstick, and read the lower level. The fluid level must be in the cross-hatched area. 4. If the fluid level is in the acceptable range, push the dipstick back in all the way and turn the handle clockwise. Reinstall the engine air cleaner/filter assembly. How to Add Automatic Transmission Fluid Refer to the Maintenance[...]

Engine Coolant The cooling system in your vehicle is filled with DEX-COOL ® engine coolant. This coolant is designed to remain in your vehicle for five years or 150,000 miles (240 000 km), whichever occurs first, if you add only DEX-COOL ® extended life coolant. The following explains your cooling system and how to add coolant when it is low. [...]

What to Use Use a mixture of one-half clean, drinkable water and one-half DEX-COOL ® coolant which will not damage aluminum parts. If you use this coolant mixture, you do not need to add anything else. { CAUTION: Adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the [...]

Checking Coolant The engine coolant surge tank is located toward the rear of the engine compartment on the passenger’s side of the vehicle. For more information on location, see Engine Compartment Overview on page 5-12 . { CAUTION: Turning the surge tank pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blo[...]

Adding Coolant If you need more coolant, add the proper DEX-COOL ® coolant mixture at the coolant surge tank, but only when the engine is cool. { CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol, and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. When repl[...]

If Steam Is Coming From Your Engine { CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Turn it off and get everyone away from the vehicle until it cools down. Wait until there is no sign of steam or coolant before you open the hood. If you[...]

If you get the overheat warning with no sign of steam, try this for a minute or so: 1. In heavy traff ic, let the engine idle in NEUTRAL (N) while stopped. If it safe to do so, pull off the road, shift to PARK (P) or NEUTRAL (N) and let the engine idle. 2. Set the climate controls to the highest heat setting and fan speed and open the windows as ne[...]

Cooling System When you decide it is safe to lift the hood, here is what you will see: A. Coolant Surge Tank with Pressure Cap B. Electric Engine Cooling Fans 4.6L L37 Engine shown, 4.6L LD8 Engine similar 5-28[...]

{ CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you. Keep hands, clothing, and tools away from any underhood electric fan. If the coolant inside the coolant surge tank is boiling, do not do anything else until it cools down. The vehicle should be parked on a level surface. { C[...]

How to Add Coolant to the Coolant Surge Tank If you have not found a problem yet, check to see if coolant is visible in the surge tank. If coolant is visible but the level is not at the FULL COLD mark located on the side of the surge tank, add enough of a 50/50 mixture of clean, drinkable water and DEX-COOL ® coolant at the coolant surge tank to b[...]

{ CAUTION: Adding only plain water to the cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, the engine could get too hot but you would not get the ove[...]

2. Then keep turning the cap and remove it. 3. Fill the coolant surge tank with the proper mixture to the FULL COLD mark on the side of the coolant surge tank. 4. With the coolant surge tank cap off, start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fans. By this time, the coola[...]

Power Steering Fluid The power steering fluid reservoir is located next to the underhood fuse block on the passenger’s side of the vehicle. See Engine Compartment Overview on page 5-12 for more information on location. When to Check Power Steering Fluid It is not necessary to regularly check power steering fluid unless you suspect there is a le[...]

Windshield Washer Fluid What to Use When you need windshield washer fluid, be sure to read the manufacturer’s instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a fluid that has suff icient protection against freezing. Adding Washer Fluid The WASHER FLUID LOW ADD FLUID me[...]

Brakes Brake Fluid The brake master cylinder reservoir is filled with DOT-3 brake fluid. See Engine Compartment Overview on page 5-12 for reservoir location and access. There are only two reasons why the brake fluid level in the reservoir might go down. The first is that the brake fluid goes down to an acceptable level during normal brake lini[...]

What to Add When you do need brake fluid, use only DOT-3 brake fluid. Use new brake fluid from a sealed container only. See Recommended Fluids and Lubricants on page 6-13 . Always clean the brake fluid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir. { CAUTION: With the wrong kind o[...]

{ CAUTION: The brake wear warning sound means that soon the brakes will not work well. That could lead to an accident. When you hear the brake wear warning sound, have your vehicle serviced. Notice: Continuing to drive with worn-out brake pads could result in costly brake repair. Some driving conditions or climates can cause a brake squeal when the[...]

Battery Your vehicle has a maintenance free battery. When it is time for a new battery, see your dealer/retailer for one that has the replacement number shown on the original battery’s label. Warning: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and r[...]

To be sure the vent hose (A) is properly attached, the vent hose connectors (B) must be securely reattached to the vent outlets (C) on each side of the battery, and the vent assembly grommet (D) must be secured to the floor pan (E). Vehicle Storage { CAUTION: Batteries have acid that can burn you and gas that can explode. You can be badly hurt if [...]

Jump Starting If your vehicle’s battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. { CAUTION: Batteries can hurt you. They can be dangerous because: • They contain acid that can burn you. • They contain gas that can explode or ignite. • [...]

Notice: If you leave your radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by your warranty. Always turn off your radio and other accessories when jump starting your vehicle. 3. Turn off the ignition on both vehicles. Unplug unnecessary accessories plugged into the cigarette l[...]

You will not see the battery of your vehicle under the hood. It is located under the rear passenger’s seat. You will not need to access the battery for jump starting. The remote terminals are for that purpose. { CAUTION: An electric fan can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from a[...]

5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock. The vehicles could be damaged too. Before you connect the cables, here are some basic things you should know. Positive (+) will go to positive (+) or to a remote positive (+) terminal if the vehicle has one. Negative ( − ) will go to a heav[...]

Notice: If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by your warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal. A. Heavy, Unpainted Metal Engine Part[...]

It is recommended that the vehicle is taken to your dealer/retailer for service if the headlamps need to be re-aimed. It is possible however, to re-aim the headlamps as described. Notice: To make sure your headlamps are aimed properly, read all the instructions before beginning. Failure to follow these instructions could cause damage to headlamp pa[...]

4. At a wall, measure from the ground upward (A) to the recorded distance from Step 3 and mark it. 5. Draw or tape a horizontal line (B) the width of the vehicle at the wall where it was marked in Step 4. Notice: Do not cover a headlamp to improve beam cut-off when aiming. Covering a headlamp may cause excessive heat build-up which may cause damage[...]

9. Make sure that the light from the headlamp is positioned at the bottom edge of the horizontal tape line. The lamp on the left (A) shows the correct headlamp aim. The lamp on the right (B) shows the incorrect headlamp aim. 10. Repeat Steps 7 through 9 for the opposite headlamp. Bulb Replacement It is recommended that all bulbs be replaced by your[...]

Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear or cracking. See Scheduled Maintenance on page 6-4 for more information on wiper blade inspection. Replacement blades come in different types and are removed in different ways. Here’s how to remove the wiper blade: 1. Turn the engine off. 2. Lift the windshiel[...]

To remove and replace the wiper blade element do the following: 1. The wiper blade element has two notches at one end which are engaged by the bottom claw set of the wiper blade. At the notched end of the wiper blade, pull the wiper blade element from the wiper blade assembly. 2. To replace the element, start at the heel end of the wiper blade, whi[...]

Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. { CAUTION: • Poorly maintained and improperly used tires are dangerous. • Overloading your tires can cause overheating as a resu[...]

Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. (A) Tire Size : The tire size is a combination of letters and numbers used to define a particular tire’s width, height, aspect ratio, construction type and service description. See the “Tire Size” illustration later in this section for more detail. (B) TPC Sp[...]

(G) Maximum Cold Inflation Load Limit : Maximum load that can be carried and the maximum pressure needed to support that load. For information on recommended tire pressure see Inflation - Tire Pressure on page 5-58 and Loading Your Vehicle on page 4-20 . (A) Temporary Use Only : The compact spare tire or temporary use tire has a tread life of app[...]

(G) TPC Spec (Tire Performance Criteria Specification) : Original equipment tires designed to GM’s specific tire performance criteria have a TPC specification code molded onto the sidewall. GM’s TPC specifications meet or exceed all federal safety guidelines. (A) Tire Size : The tire size code is a combination of letters and numbers used to[...]

(G) Single Tire Maximum Load : Maximum load that can be carried and the maximum pressure needed to support that load when used as a single. For information on recommended tire pressure see Inflation - Tire Pressure on page 5-58 . Tire Size The following illustration shows an example of a tire size. (A) P-Metric Tire : The United States version of [...]

Tire Terminology and Definitions Air Pressure : The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight : This means the combined weight of optional accessories. Some examples of optional accessories are, automatic transmissi[...]

GAWR RR : Gross Axle Weight Rating for the rear axle. See Loading Your Vehicle on page 4-20 . Intended Outboard Sidewall : The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa) : The metric unit for air pressure. Light Truck (LT-Metric) Tire : A tire used on light duty trucks and some multipurpo[...]

Radial Ply Tire : A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim : A metal support for a tire and upon which the tire beads are seated. Sidewall : The portion of a tire between the tread and the bead. Speed Rating : An alphanumeric code assigned to a tire indicating the ma[...]

Inflation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inflation or over-inflation is all right. It is not. If your tires do not have enough air (under-inflation), you can get the following: • Too much flexing • Too much heat • Tire overloading • Pre[...]

How to Check Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they are under-inflated. Check the tire’s inflation pressure when the tires are cold. Cold means your vehicle has been sitting for at least th[...]

High-Speed Operation { CAUTION: Driving at high speeds, 100 mph (160 km/h) or higher, puts an additional strain on tires. Sustained high-speed driving causes excessive heat build up and can cause sudden tire failure. You could have a crash and you or others could be killed. Some high-speed rated tires require inflation pressure adjustment for high[...]

Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your vehicle’s tires and transmit tire pressure readings to a receiver located in the vehicle. Each tire, including the spare (if provided), should be checked monthly whe[...]

Federal Communications Commission (FCC) and Industry and Science Canada The Tire Pressure Monitor System (TPMS) operates on a radio frequency and complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, inclu[...]

At the same time a message to check the pressure in a specific tire appears on the Driver Information Center (DIC) display. The low tire pressure warning light and the DIC warning message come on at each ignition cycle until the tires are inflated to the correct inflation pressure. Using the DIC, tire pressure levels can be viewed by the driver.[...]

TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light flashes for about one minute and then stays on for the remainder of the ignition cycle. A DIC warning message is also displayed. The low tire warning [...]

TPMS Sensor Matching Process Each TPMS sensor has a unique identification code. Any time you rotate your vehicle’s tires or replace one or more of the TPMS sensors, the identification codes will need to be matched to the new tire/wheel position. The sensors are matched to the tire/wheel positions in the following order: driver side front tire, [...]

6. Proceed to the passenger side front tire, and repeat the procedure in Step 5. 7. Proceed to the passenger side rear tire, and repeat the procedure in Step 5. 8. Proceed to the driver side rear tire, and repeat the procedure in Step 5. The horn sounds two times to indicate the sensor identification code has been matched to the driver side rear t[...]

If your vehicle has a compact spare tire, it should not be included in the tire rotation process. Use the four-tire rotation pattern shown. A five-tire rotation pattern may be used for your professional vehicle, if it has a full-size spare tire and wheel assembly that matches the original equipment tires and wheels in size, type and brand. The cor[...]

Vehicles that have the Tire Pressure Monitor System (TPMS) will need to have the sensors reset after a tire rotation is performed. See Tire Pressure Monitor System on page 5-61 . Make certain that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Specifications on page 5-105 . { CAUTION: Rust or dirt on a wheel[...]

You need new tires if any of the following statements are true: • You can see the indicators at three or more places around the tire. • You can see cord or fabric showing through the tire’s rubber. • The tread or sidewall is cracked, cut, or snagged deep enough to show cord or fabric. • The tire has a bump, bulge, or split. • The tire h[...]

GM recommends replacing tires in sets of four. This is because uniform tread depth on all tires will help keep your vehicle performing most like it did when the tires were new. Replacing less than a full set of tires can affect the braking and handling performance of your vehicle. See Tire Inspection and Rotation on page 5-66 for information on pro[...]

If you must replace your vehicle’s tires with those that do not have a TPC Spec number, make sure they are the same size, load range, speed rating, and construction type (radial and bias-belted tires) as your vehicle’s original tires. Vehicles that have a tire pressure monitoring system could give an inaccurate low-pressure warning if non-TPC S[...]

Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traff ic Safety Administration (NHTSA), which grades tir[...]

Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce ti[...]

Wheel Replacement Replace any wheel that is bent, cracked or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts and wheel nuts should be replaced. If the wheel leaks air, replace it. Some aluminum wheels can sometimes be repaired. See your GM dealer/retailer if any of these conditions exist. Your GM dealer/retailer wi[...]

Used Replacement Wheels { CAUTION: Putting a used wheel on your vehicle is dangerous. You cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel. Tire Chains { CAUTION: Do not use tire chains. There is not enough clearance. Tire [...]

If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle’s tires properly. If air goes out of a tire, it is much more likely to leak out slowly. But if you should ever have a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire creates[...]

Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your vehicle’s hazard warning flashers. See Hazard Warning Flashers on page 3-6 for more information. { CAUTION: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other peopl[...]

Removing the Spare Tire and Tools The equipment needed is in the trunk. To access the equipment: 1. Open the trunk. See Trunk on page 2-12 for more information. 2. Press the area at the front of the handle located on the cover so that the back edge raises. 3. Grab the handle and remove the cover. 4. Turn the wing nut to remove the retainer that hol[...]

5. Remove the wheel wrench, jack and spare tire from the trunk. See Spare Tire on page 5-86 for more information. The tools to be used are the jack (A) and the wheel wrench (B). Removing the Flat Tire and Installing the Spare Tire 1. Do a safety check before proceeding. See Changing a Flat Tire on page 5-77 for more information. 2. For models havin[...]

3. For models with exposed lug nuts, loosen them using the wheel wrench. Do not remove them yet. 4. Find the jacking location from the diagram above and use the corresponding cutouts located in the plastic molding. The front location is (A) 8.5 inches (21 cm) from the rear edge of the front wheel well, and the rear location (B) is 3.5 inches (8.5 c[...]

{ CAUTION: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. { CAUTION: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid persona[...]

8. Raise the vehicle by turning the jack handle clockwise. Raise the vehicle far enough off the ground for the spare tire to fit under the vehicle. 9. Remove all wheel nuts and the flat tire. 10. Remove any rust or dirt from the wheel bolts, mounting surfaces, and spare wheel. { CAUTION: Rust or dirt on a wheel, or on the parts to which it is fas[...]

11. Place the spare tire on the wheel-mounting surface. { CAUTION: Never use oil or grease on studs or nuts. Because the nuts might come loose. The vehicle’s wheel could fall off, causing a crash. 12. Put the wheel nuts back on with the rounded end of the nuts toward the wheel. Tighten each nut by hand until the wheel is held against the hub. 13.[...]

{ CAUTION: Incorrect or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to a crash. If you have to replace them, be sure to get new original equipment wheel nuts. Stop somewhere as soon as you can and have the nuts tightened with a torque wrench to the proper torque specification. See Capacities[...]

Storing a Flat or Spare Tire and Tools { CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place. After you have put the spare tire on your vehicle, store the flat tire in your trunk. [...]

4. Secure the spare tire and the jack container with the retainer (C) and then the wing nut (B). 5. Reinstall the spare tire cover (A). Spare Tire Compact Spare Tire Your vehicle may have a compact spare tire. Although the compact spare tire was fully inflated when the vehicle was new, it can lose air after a time. Check the inflation pressure re[...]

Your vehicle may have a different size spare tire than the road tire originally installed on your vehicle. This spare tire was developed for use on your vehicle, so it is all right to drive on it. If your vehicle has a spare tire that does not match your vehicle’s original road tires and wheels in size and type, do not include the spare in the ti[...]

Do not clean your vehicle using the following cleaners or techniques: • Never use a knife or any other sharp object to remove a soil from any interior surface. • Never use a stiff brush. It can cause damage to your vehicle’s interior surfaces. • Never apply heavy pressure or rub aggressively with a cleaning cloth. Use of heavy pressure can [...]

If any of the soil remains, a commercial fabric cleaner or spot lifter may be necessary. When a commercial upholstery cleaner or spot lifter is to be used, test a small hidden area for colorfastness first. If the locally cleaned area gives any impression that a ring formation may result, clean the entire surface. After the cleaning process has bee[...]

Speaker Covers Vacuum around a speaker cover gently, so that the speaker will not be damaged. Clean spots with just water and mild soap. Care of Safety Belts Keep belts clean and dry. { CAUTION: Do not bleach or dye safety belts. If you do, it may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety [...]

High pressure car washes may cause water to enter the vehicle. Avoid using high pressure washes closer than 12 inches (30 cm) to the surface of the vehicle. Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals. Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water, a soft cloth and a car [...]

Use special care with aluminum trim. To avoid damaging protective trim, never use auto or chrome polish, steam or caustic soap to clean aluminum. A coating of wax, rubbed to high polish, is recommended for all bright metal parts. Windshield and Wiper Blades Clean the outside of the windshield with glass cleaner. Clean the rubber blades using a lint[...]

The surface of these wheels is similar to the painted surface of your vehicle. Do not use strong soaps, chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on them because you could damage the surface. Do not use chrome polish on aluminum wheels. Notice: Using chrome polish on aluminum wheels could dama[...]

Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, corrosion and rust can develop on the underbody parts such as fuel lines, frame, floor pan, and exhaust system even though they have corrosion protection. At least every spring, flush these materials from the unde[...]

Description Usage Swirl Remover Polish Removes swirl marks, fine scratches, and other light surface contamination. Cleaner Wax Removes light scratches and protects finish. Foaming Tire Shine Low Gloss Cleans, shines, and protects tires. No wiping necessary. Wash Wax Concentrate Medium foaming shampoo. Cleans and lightly waxes. Biodegradable and p[...]

Service Parts Identification Label This label is on the spare tire cover. It is very helpful if you ever need to order parts. The label has the following information: • Vehicle Identification Number (VIN) • Model designation • Paint information • Production options and special equipment Do not remove this label from the vehicle. Electrica[...]

Power Windows and Other Power Options Circuit breakers in the fuse block protect the power windows and other power accessories. When the current load is too heavy, the circuit breaker opens and closes, protecting the circuit until the problem is fixed or goes away. Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from s[...]

Fuses Usage 1 Engine Control Module (ECM), Crank 2 Fuel Injectors Odd 3 Fuel Injectors Even Fuses Usage 4 Air Conditioning Clutch 5 Air Injection Reactor (AIR) Solenoid 6 Oxygen Sensor 5-98[...]

Fuses Usage 7 Emission Device 8 Transmission, Ignition 1 9 Engine Control Module (ECM), Powertrain Control Module (PCM) 10 Climate Control System, Instrument Panel Cluster Ignition 1 11 Airbag System 12 Horn 13 Windshield Wiper 14 Fog Lamps 15 Right High-Beam Headlamp 16 Left High-Beam Headlamp 17 Left Low-Beam Headlamp 18 Right Low-Beam Headlamp 1[...]

Rear Underseat Fuse Block The rear fuse block is located under the rear seat on the driver side. The rear seat cushion must be removed to access the rear fuse block. Removing the Rear Seat Cushion Notice: If you touch the exposed wires with the metal on the seat cushion, you could cause a short that could damage the battery and or wires. Avoid cont[...]

To reinstall the rear seat cushion, do the following: { CAUTION: A safety belt that is not properly routed through the seat cushion or is twisted will not provide the protection needed in a crash. CAUTION: (Continued) CAUTION: (Continued) If the safety belt has not been routed through the seat cushion at all, it will not be there to work for the ne[...]

Fuses Usage 1 Fuel Pump 2 Left Park Lamp 3 Run 3 - Rear Blower Fuses Usage 4 Right Park Lamp 5 Engine Control Module (ECM)/ Transmission Control Module (TCM) 5-102[...]

Fuses Usage 6 Memory Module 7 Right Park Lamp (optional) 8 Steering Wheel Illumination 9 Front Heated/Cooled Seat Module 10 Run 2 - Heated/Cooled Seats, Heated Washer Fluid 11 Rear Heated Seat Module 12 RPA Module 13 PASS-Key ® III System 14 Unlock/Lock Module 15 Magnetic Ride Control 16 Daytime Running Lamps (DRL) (optional) 17 Sunroof 18 Body Co[...]

Fuses Usage 41 Stoplamp (optional) 42 OnStar ® Module 43 Body Modules 44 Radio 45 Door Unlatch (optional) 46 Rear Defogger (J-Case) 47 Electronic Leveling Control Compressor (J-Case) 48 Blower (J-Case) (optional) 49 Blower (J-Case) (optional) Resistor Usage 50 Terminating Resistor Relays Usage 51 Front Blower (optional) 52 Rear Defogger 53 Electro[...]

Capacities and Specifications The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-13 for more information. Application Capacities English Metric Air Conditioning Refrigerant For the air conditioning system refrigerant charge amount, see the refrigerant caution label loca[...]

✍ NOTES 5-106[...]

Maintenance Schedule ..................................... .6-2 Introduction .................................................. .6-2 Maintenance Requirements ............................. .6-2 Your Vehicle and the Environment ................... .6-2 Using the Maintenance Schedule ..................... .6-3 Scheduled Maintenance ...................[...]

Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer/retailer for details. Maintenance Requirements Notice: Maintenance intervals, checks, i[...]

Using the Maintenance Schedule We want to help you keep your vehicle in good working condition. But we do not know exactly how you will drive it. You might drive very short distances only a few times a week. Or you might drive long distances all the time in very hot, dusty weather. You might use your vehicle in making deliveries. Or you might drive[...]

When you go to your dealer/retailer for your service needs, you will know that trained and supported service technicians will perform the work using genuine parts. If you want to purchase service information, see Service Publications Ordering Information on page 7-15 . Owner Checks and Services on page 6-9 tells you what should be checked, when to [...]

If the engine oil life system is ever reset accidentally, you must service your vehicle within 3,000 miles (5 000 km) since your last service. Remember to reset the oil life system whenever the oil is changed. See Engine Oil Life System on page 5-16 for information on the Engine Oil Life System and resetting the system. When the CHANGE ENGINE OIL S[...]

Additional Required Services The following services should be performed at the first maintenance service after the indicated miles (kilometers) shown for each item. Additional Required Services Service and Miles (Kilometers) 25,000 (40 000) 50,000 (80 000) 75,000 (120 000) 100,000 (160 000) 125,000 (200 000) 150,000 (240 000) Inspect fuel system f[...]

Additional Required Services (cont’d) Service and Miles (Kilometers) 25,000 (40 000) 50,000 (80 000) 75,000 (120 000) 100,000 (160 000) 125,000 (200 000) 150,000 (240 000) Replace spark plugs. An Emission Control Service. • Except Professional Vehicle: Engine cooling system service (or every five years, whichever occurs first). An Emission Co[...]

Maintenance Footnotes (a) Visually inspect brake lines and hoses for proper hook-up, binding, leaks, cracks, chafing, etc. Inspect disc brake pads for wear and rotors for surface condition. Inspect other brake parts, including calipers, parking brake, etc. (b) Visually inspect front and rear suspension and steering system for damaged, loose, or mi[...]

(j) Drain, flush, and refill cooling system. This service can be complex; you should have your dealer/retailer perform this service. See Engine Coolant on page 5-22 for what to use. Inspect hoses. Clean radiator, condenser, pressure cap, and filler neck. Pressure test the cooling system and pressure cap. (k) A fluid loss in any vehicle system c[...]

At Least Once a Month Tire Inflation Check Inspect your vehicle’s tires and make sure they are inflated to the correct pressures. Do not forget to check the spare tire. See Inflation - Tire Pressure on page 5-58 . Check to make sure the spare tire is stored securely. See Changing a Flat Tire on page 5-77 . Tire Wear Inspection Tire rotation ma[...]

Automatic Transmission Shift Lock Control System Check { CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before you start, be sure you have enough room around the vehicle. It should be parked on a level surface. 2. Firmly apply the parking brake. See Parking Brak[...]

Parking Brake and Automatic Transmission Park (P) Mechanism Check { CAUTION: When you are doing this check, your vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of your vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin t[...]

Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number, or specification can be obtained from your dealer/retailer. Usage Fluid/Lubricant Engine Oil The engine requires a special engine oil meeting GM Standard GM4718M. Oils meeting this standard can be identified as synthetic, and should also be identified[...]

Normal Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your dealer/retailer. Part GM Part Number ACDelco ® Part Number Engine Air Cleaner/Filter Element 22676970 A1627C Engine Oil Filter 89017342 PF61 Passenger Compartment Air Filter Element 25689297 CF118C Spark Plugs [...]

Engine Drive Belt Routing 4.6L V8 Engines 6-15[...]

Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2 . Any additional information from Owner Checks and Services on page 6-9 can be added on the following record pages. You should[...]

Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance Stamp Services Performed 6-17[...]

Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance Stamp Services Performed 6-18[...]

Customer Assistance and Information .............. .7-2 Customer Satisfaction Procedure ..................... .7-2 Online Owner Center ..................................... .7-4 Customer Assistance for Text Telephone (TTY) Users ............................... .7-5 Customer Assistance Off ices ........................... .7-5 GM Mobility Reimbursem[...]

Customer Assistance and Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Cadillac. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer’s sales or service departments. Sometimes, however, despite the best intentions of all c[...]

filing a court action, use of the program is free of charge and your case will generally be heard within 40 days. If you do not agree with the decision given in your case, you may reject it and proceed with any other venue for relief available to you. You may contact the BBB Auto Line Program using the toll-free telephone number or write them at t[...]

Online Owner Center Online Owner Center (United States only) The Owner Center is a resource for your GM ownership needs. Specific vehicle information can be found in one place. The Online Owner Center allows you to: • Get e-mail service reminders. • Access information about your specific vehicle, including tips and videos and an electronic ve[...]

Customer Assistance for Text Telephone (TTY) Users To assist customers who are deaf, hard of hearing, or speech-impaired and who use Text Telephones (TTYs), Cadillac has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with Cadillac by dialing: 1-800-833-CMCC (2622). (TTY users in Canada can dial 1-800-263-383[...]

Overseas — Customer Assistance Please contact the local General Motors Business Unit. Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) — Customer Assistance General Motors de Mexico, S. de R.L. de C.V. Customer Assistance Center Paseo de la Reforma # 2740 Col. Lomas de Bezares C.P. 11910, Mexi[...]

Roadside Service In the United States or Canada, call 1-800-882-1112 . Text Telephone (TTY), U.S. only, call 1-888-889-2438. Service is available 24 hours a day, 365 days a year. As the owner of a new Cadillac vehicle, you are automatically enrolled in the Cadillac Roadside Service ® program. Who Is Covered? Roadside Service coverage is for the ve[...]

• Trip Routing Service: Upon request, Cadillac Roadside Service will send you detailed, computer personalized maps, highlighting your choice of either the most direct route or the most scenic route to your destination, anywhere in North America, along with helpful travel information pertaining to your trip. Please allow three weeks before your pl[...]

• Odometer reading, Vehicle Identification Number (VIN), and delivery date of the vehicle • Description of the problem Towing and Road Service Exclusions Specifically excluded from Roadside Service coverage are towing or services for vehicles operated on a non-public roadway or highway, fines, impound towing caused by a violation of local, M[...]

Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait, GM helps to minimize your inconvenience by providing several transportation options. Depending on the circumstances, your dealer can offer you one of the following: Shuttle Service Participating dealers can provide shuttle service [...]

Additional Program Information All program options, such as shuttle service, may not be available at every dealer. Please contact your dealer for specific information about availability. All Courtesy Transportation arrangements will be administered by appropriate dealer personnel. General Motors reserves the right to unilaterally modify, change, o[...]

Repair Facility GM also recommends that you choose a collision repair facility that meets your needs before you ever need collision repairs. Your GM dealer/retailer may have a collision repair center with GM-trained technicians and state of the art equipment, or be able to recommend a collision repair center that has GM-trained technicians and comp[...]

• Gather the important information you will need from the other driver. Things like name, address, phone number, driver’s license number, vehicle license plate, vehicle make, model and model year, Vehicle Identification Number (VIN), insurance company and policy number, and a general description of the damage to the other vehicle. • If possi[...]

Reporting Safety Defects Reporting Safety Defects to the United States Government If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traff ic Safety Administration (NHTSA) in addition to notifying General Motors. If NHTSA receives similar complai[...]

Service Publications Ordering Information Service Manuals Service Manuals have the diagnosis and repair information on engines, transmission, axle suspension, brakes, electrical, steering, body, etc. Service Bulletins Service Bulletins’ give additional technical service information needed to knowledgeably service General Motors cars and trucks. E[...]

Vehicle Data Recording and Privacy Your GM vehicle has a number of sophisticated computers that record information about the vehicle’s performance and how it is driven. For example, your vehicle uses computer modules to monitor and control engine and transmission performance, to monitor the conditions for airbag deployment and deploy airbags in a[...]

To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR. GM will not access this data or share it with others[...]

✍ NOTES 7-18[...]

A Accessories and Modifications ............................ 5 - 3 Adaptive Cruise Control ................................... 3-19 Adding Equipment to Y our Airbag-Equipped V ehicle ....................................................... 1-68 Additives, Fuel ................................................. 5 - 6 Add-On Electrical Equipment .....[...]

Ashtray(s) ...................................................... 3-39 Audio System ................................................. 3-95 Audio Steering Wheel Controls .................... 3-117 Backglass Antenna ..................................... 3-119 Navigation/Radio System, see Navigation Manual ............................ 3-116 Radio Rece[...]

Chains, T ire ................................................... 5-75 Charging System Light .................................... 3-58 Check Engine Light ............................................... 3-63 Checking Things Under the Hood ...................... 5-10 Chemical Paint Spotting ................................... 5-94 Child Restraints Ch[...]

Cooled Seats ................................................... 1 - 3 Cooling System .............................................. 5-28 Cornering Lamps ............................................ 3-35 Courtesy Lamps ............................................. 3-35 Cruise Control ................................................ 3-16 Cruise Cont[...]

E E D R ............................................................. 7-16 Electrical System Add-On Equipment ...................................... 5-96 Fuses and Circuit Breakers ........................... 5-97 Headlamp Wiring ......................................... 5-96 Power Windows and Other Power Options ...... 5-97 Rear Underseat Fuse Blo[...]

Fuel ............................................................... 5 - 5 Additives ...................................................... 5 - 6 California Fuel .............................................. 5 - 6 Filling a Portable Fuel Container .................... 5-10 Filling the T ank ............................................. 5 - 8 Fuels[...]

I Ignition Positions ............................................. 2-23 Inadvertent Power Battery Saver ....................... 3-38 Infants and Y oung Children, Restraints ............... 1-34 Inflation - T ire Pressure ................................... 5-58 Instrument Panel Overview ..................................................... 3 - 4 I[...]

Light (cont.) TCS W arning Light ...................................... 3-60 T ire Pressure .............................................. 3-62 T raction Control System (TCS) W arning .......... 3-60 Lighting Entry ......................................................... 3-36 Parade Dimming .......................................... 3-36 Lights Ex[...]

Mirrors Automatic Dimming Mirror with Intellibeam™, OnStar ® , and Compass ............................. 2-36 Automatic Dimming Rearview with Compass .... 2-40 Automatic Dimming Rearview with OnStar ® and Compass .......................................... 2-38 Manual Rearview Mirror with Compass and T emperature ................................[...]

P Paint, Damage ............................................... 5-93 Panic Brake Assist ............................................ 4 - 7 Parade Dimming ............................................. 3-36 Park Aid ........................................................ 2-44 Park Brake .................................................... 2-30 Park [...]

Rearview Mirror , Automatic Dimming with Compass ............................................. 2-40 Rearview Mirror , Automatic Dimming with OnStar ® and Compass .......................... 2-38 Rearview Mirror with Compass and T emperature ..... 1 - 9 Reclining Seatbacks, Power ............................... 1 - 6 Recommended Fluids and Lubricant[...]

Security Light ................................................. 3-66 Service ........................................................... 5 - 3 Accessories and Modifications ......................... 5 - 3 Adding Equipment to the Outside of Y our V ehicle .......................................... 5 - 5 California Pershlorate Materials Requirement[...]

T ilt Wheel ........................................................ 3 - 6 T ime, Setting .................................................. 3-96 T ire Pressure Light ............................................. 3-62 T ires ............................................................. 5-50 Aluminum or Chrome-Plated Wheels, Cleaning ...............[...]

V V alet Lockout Switch ....................................... 2-18 V ehicle Control ........................................................ 4 - 3 Damage W arnings ........................................... i v Loading ...................................................... 4-20 Symbols ......................................................... i [...]