Carl 540 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Carl 540, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Carl 540 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Carl 540. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Carl 540 should contain:
- informations concerning technical data of Carl 540
- name of the manufacturer and a year of construction of the Carl 540 item
- rules of operation, control and maintenance of the Carl 540 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Carl 540 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Carl 540, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Carl service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Carl 540.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Carl 540 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    CARL GOLDBERG PRODUCTS L T D . P .O. Box 818, Oakwood, GA 30566 • 678-450-0085 • Fax: 770-532-2163 • www .carlgoldbergproducts.com ©copyright 2003 Carl Goldberg Products, Ltd.[...]

  • Page 2

    2 W W A A R R N N I I N N G G ! ! T T H H I I S S I I S S N N O O T T A A T T O O Y Y ! ! T T H H I I S S I I S S N N O O T T A A B B E E G G I I N N N N E E R R S S A A I I R R P P L L A A N N E E This R/C kit and the model y ou will build fr om it is not a to y! It is capable of serious bodil y harm and property damage. It is y our responsibility[...]

  • Page 3

    3 Ex-tr Ex-tr eme 5 eme 5 40 40 Congratulations on y our purc hase of the Lanier Ex-treme 540 3-D ARF . This is a very unique air cr af t, with great 3-D capabilities. Every effort has been made to produce a lightweight, str aight, easy to assemble aircr af t. Because of its o versize control surf aces whic h are double beveled to allow for extreme[...]

  • Page 4

    4 Part s Layo ut[...]

  • Page 5

    5 2.5mmx1 0mm scre ws 7 3 t ail wheel mount 4 wire holder 2.5mmx8mm screws 8 hatch co v ers 2mmx20mm screws 8 control horns 3mmx30mm screws 2 landing gear 3mmx20mm screws 4 motor mount 3mm lock nuts 6 2 landing gear 4 motor mount 3mm w asher 1 2 4 landing gear 8 motor mount axles 2 8mm lock nuts 2 axle mount 8mm w asher 2 axle mount 4mm wheel colla[...]

  • Page 6

    6 BUI LDI NG INST RUCTI ONS Before st arting to build t his kit, we urg e y ou to read through these instructions. They cont ain some import ant building sequences as w ell as instructions and w arnings con- cerning the assembl y and use of the model. We expect that y ou ha v e some build- ing experience to t ake on this model. Ho we ver, ev ery mi[...]

  • Page 7

    7 It is easier to do some of the w ork on the wing and fuselage before y ou glue them together. Locate the tem- plate at the rear of the book for locating the landing gear and cut it out with scissors. Place it o v er the fuselage and drill 1/8” holes at the location of the mounting holes. Check the aluminum g ear and make sure it matches the hol[...]

  • Page 8

    8 measure back fr om t he opening 1- 3/8” and cut a slot 1/8” wide cen- tered on the mark y ou made. we are now ready to mount the wing on the fuselage. Slide the wing back in the fuse, almost to the wing joint. Coat t he bare balsa at the joint with 30 minute z po xy and slide the wing in t he rest of the w a y . Use y our marks to realign the[...]

  • Page 9

    9 Inst all t he gear on the fuselage using the tw o 3mmx30mm bolts, four 3mm flat w asher, and tw o 3mm lock nuts. Locate the ele v ator joiner wire and the tw o elev ator hal v es. Measure the width of the s t ab and la y the ele v a- tors spread to that length. Mark the location of the holes for the elev a- tor joiner wire on the st ab. width of [...]

  • Page 10

    10 Glue the joiner wire in place with epo xy . Make sure the ele v ators are l ying on a flat surf ace so both will be par allel. Use a str aight edge to make sure the leading edge is str aight and the tips are at t he prop- er width. Fit the elev ators in place on the CA hinges. Deflect the elev ator to full tr a v el and glue hing es with two dr [...]

  • Page 11

    11 A t t he location of the elev ator wire make a notch appr o ximat el y 3/1 6” deep and 3/8” wide to clear the ele- v ator wire. A t t he location of the tiller arm drill a 3/32” hole and slot the leading edge of the rudder to accept t he t ail wheel wire. notch f or elev ator wire hole for t ail wheel wire Slide a piece of masking t ape be[...]

  • Page 12

    12 Align the aileron control horn Using the line y ou dre w earlier for the pushrod slot. Mark the location of the holes and drill tw o 5/64” holes. Inst all t he horn with two 2mmx20mm screws and the ny lon plate on top. Locate one of the 2mm pushrods with clevis. ins t all the silicone k eep- er o v er the clevis and att ach to the control horn[...]

  • Page 13

    13 The battery will mount on the left side. Wrap with foam rubber(not sho wn for clarity) and insert into opening. The receiver will mount on the right side in the opening ne xt to the serv o. Wrap with foam rubber(not sho wn). Route the antenna under the pushrod and exit from a hole close to the side of the fuselage. It can then be pulled do wn th[...]

  • Page 14

    14 It will be necessar y to cut the back side out of the n ylon co ver for the wires to fit in. Using a sharp knife, cut 1/1 6” inside the edge of the co v er. Make sure y ou are cutting the back side, it fits on the right side of the plane. The wires can then be fit- ted inside by st aggering the plugs. location of hole in wing Hold the wire co [...]

  • Page 15

    15 Align the elev ator horn on t he inside edge of the elev ator and mount using the tw o #2x1” screws and ny lon plate. Locate the two 2mm pushr ods with clevis and inst all the silicone k eeper on clevis. Hook cle vis to horn and mark where it meets the serv o arm. Make a 90 degree bend and cut at 3/8”. Y ou will need to drill out t he ser v [...]

  • Page 16

    16 . If y ou use a mini serv o t hese will not be used. If y ou use a st andard serv o y ou will need them to clear the ser v o. Assemble the t ank cap wit h the big w asher, the rubber stopper, and the little w asher in t he rear. F or a two line system we will onl y use the long piece of aluminum tube and one short one. Insert the tubes through t[...]

  • Page 17

    17 Mount the throttle ser v o using t he hardw are supplied wit h the r adio. Use the1 .5 mm x 6”pushrod and bend a z bend in one end and att ach to the throttle arm on motor. A tt ach the e- z connector to a three hole serv o arm and att ach to ser vo. Make a small hole on the bottom of the wing on the lef t side to pass the throttle ser vo lead[...]

  • Page 18

    18 The CG should be between 4-3/4” and 5-1/4” for first flight. F or 3-D it can be mo v ed back after y ou are comfort- able with the plane. Ha ve fun! A A d d d d i i t t i i o o n n a a l l E E q q u u i i p p m m e e n n t t n n e e e e d d e e d d t t o o c c o o m m p p l l e e t t e e y y o o u u r r E E x x -T T r r e e m m e e 5 5 4 4 0[...]

  • Page 19

    19 Exit hole location to be marked on the wing[...]

  • Page 20

    20[...]

  • Page 21

    21 Optional Landing Gear A vailable Make your Extreme 330 different from the crowed! Our new # 257 Profile Nylon Landing Gear will fit you Extreme 300 and look great too. This Landing gear also includes our new # 302 5/32 x 1-1/2” Polished Nickel Landing Gear axles to give you extra value. 1. Mount the nylon gear in the same location as the alumi[...]

  • Page 22

    22 EX-TREME 330 3-D ARF The Elevator This maneuver has your plane drop vertically in a nose high attitude, depending on wind conditions any where from a 45 degree angle in low wind to almost backwards in higher wind conditions. To perform it, at a high altitude with high rates on, pull your th rottle back and feed in the elevator until you have the[...]

  • Page 23

    23 EX-TREME 330 3-D ARF The Waterfall This maneuver has your plane fl ipping around the axis of the wing, while dropping. Starting from a high altitude, go to low throttle and gradua lly pull the nose up to near vertical. Just when the plane is about the stall, give it full down elevator and full power. Make attitude corrections with the rudder and[...]