Carson 1181281 manual

1
2
3
4
5
6
7
8
9
10
11
12

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Carson 1181281, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Carson 1181281 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Carson 1181281. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Carson 1181281 should contain:
- informations concerning technical data of Carson 1181281
- name of the manufacturer and a year of construction of the Carson 1181281 item
- rules of operation, control and maintenance of the Carson 1181281 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Carson 1181281 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Carson 1181281, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Carson service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Carson 1181281.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Carson 1181281 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    INSTALLATION INSTRUCTIONS FOR 50 - 0212x - 002 SERIES 1181281 50 - 0212x - 014 SERIES 1181280 FORD EXPEDITION OVERHEAD CONSOLE for use with FLIPDOWN VIDEO SYSTEM These instructions are intended for use only by experienced professional s in the automotive customizing business. Special tools and equipment, as well as specialized handling and care of [...]

  • Page 2

    2 ITEM DESCRIPTION QTY 1 Nut, 6 - 32 HH KEPS 8 2 Screw, # 6 x 3/8 PPH TAB 13 3 Screw, # 8 x 9/16 PWH TAB 2 4 Screw, 6 - 32 x 1/2 PPH 4 5 Screw, 6 - 32 x 3/4 PPH 10 6 Screw, # 8 x 1 1/4 PWH TAB 2 7 Screw, # 8 x 1 1/2 PWH TAB 1 8 Screw, # 8 x 1 3/4 POH TAB Z1 2 9 Washer, 3.5 mm 4 10 Finish Washer, # 8 2 11 Convoluted Tube, 1/2" ID X 3" 1 12[...]

  • Page 3

    3[...]

  • Page 4

    4 I. REMOVAL OF O.E.M. EQUIPMENT. 1. Remove and retain OEM overhead console assembly by removing one (1) OEM screw in front pocket. Pull console down and disconnect wiring. Set aside in a safe place for later re - installation. 2. Remove and retain rear A/C control assembly. Assembly housing is secured with two (2) spring loaded f asteners on front[...]

  • Page 5

    5 3. Install block - off cover (item 16 pg 2) using one (1) # 8 x 1 1/4" PWH screw (it em 6 pg 2). See Fig. 4. (Use caution to assure screw does not penetrate vehicle roof ). 4. Detach wire harness from brace where A/C assembly was removed. Remove and retain two (2) OEM screws. Trim headliner to clear front flange of rear moun ting bracket (it[...]

  • Page 6

    6 6. Install video system wiring into vehicle. Route video system cables from installed position in center of roof to “B” - pillar. Down “B” - pillar to floor. Route power and ground leads forward to fuse box area. Connect power wire to a fused accessory controlled power source per instructions provided in video system. Ground negative lead[...]

  • Page 7

    7 3. Attach four (4 ) pod mounting brackets (item 14 pg 2) to front and rear of be zel with four (4 ) 6 - 32 X 1/2" screws (item 4 pg 2) and four (4) 8 - 32 KEPS nuts (item 1 pg 2). See Figure 10. 4. Install and secure O.E. bezel in overhead console (item 19 pg 2) with eight ( 8 ) # 6 X 3/8" PPH screws (item 2 pg 2) As shown. See Figure 1[...]

  • Page 8

    8 5. Remove two (2) plastic tabs on secondary light and pod assembly, replace two ( 2 ) OEM screws in front assembly as shown. See Figure 12. 6. Install and secure secondary light pod assembly in overhead console with six ( 6 ) OEM screws. See Figure13. Note: Be sure light wiring is accessible. Figure 12 Figure 13[...]

  • Page 9

    9 7. Remove A/C control from rear bezel assembly. Modify A/C co ntrol by drilling three (3) 1/8" dia. holes in front mounting tabs. Position rear A/C control head in center of overhead opening. Secure with five (5) # 6 X 3/8" PPH screws (item 2 pg 2). See Figure 14. 8. If vehicle is equipped with O EM vent switches, remove and discard bla[...]

  • Page 10

    10 1. Raise overhead console into approximate position and connect wiring to components. 2. Loosely fit console against headliner. Check that console is centered in vehicl e and matches all contours of headliner. While supporting console in mounting position, loosely install using two (2) 6 - 32 X 3/4" screws (item 5 pg 2) through the smaller [...]

  • Page 11

    11 6. Release video screen from locked position. Lower video screen t o viewing position for access to mounting locations in top of video system housing. 7. Raise video system into approximate position and connect all wiring to components. Route video cable through hole in mounting bracket. Connect wiring and cabling to vide o system per instructio[...]

  • Page 12

    12 CUT ON DOTTED LINES[...]