Casio IT-9000 manual

Handheld Printer T erminal User’ s Guide Be sure to r ead “Safety Precautions” inside this guide before trying to use your Handheld Printer T erminal. E Series IT-9000[...]

Information in this document is subject to change without advance notice. CASIO Computer Co., Ltd. makes no representations or warranties with respect to the contents or use of this manual and speci fi cally disclaims any express or implied warranties of merchantability or fi tness for any particular purpose. BLUETOOTH is a registered trademark o[...]

E-1 Contents Safety Precautions ......................................................................................... E-3 Operating Precautions ................................................................................... E-9 Important ...................................................................................................... E[...]

E-2 Handling Magnetic Card Reader ................................................................. E-42 Handling the NFC Reader/Writer ................................................................ E-43 RFID T ags .......................................................................................................... E-43 Contactless IC Cards [...]

E-3 Safety Pr ecautions Congratulations upon your selection of this CASIO product. Be sure to read the following Safety Precautions before trying to use it for the fi rst time. Y our neglect or avoidance of the warning and caution statements in the subsequent pages causes the danger of fi re, electric shock, malfunction and damage on the goods as[...]

E-4 W arning Dust and Moisture Though the Handheld Printer T erminal is dust and water splash resistant, its options including the battery pack are not. Keep loose metal objects and containers fi lled with liquid away from your Handheld Printer T erminal and the options. Also, never handle the Handheld Printer T erminal and the options while your [...]

E-5 Caution Foreign Objects T ake care to ensure that metals or combustible objects are not inserted into the openings of the Handheld Printer T erminal or its options, and not to allow moisture to get inside of them. Location Install the cradle properly on a fl at and stable surface so that it cannot fall down onto fl oor . LCD Screen Never appl[...]

E-6 Caution Installing in V ehicle T o save your vehicle’ s battery from running down, be sure that the Car Power Cable should be unplugged from the cigarette lighter socket when you do not use the Car Mounted-type Battery Charger and that the use of the battery charger should be avoid while the vehicle’ s engine is turned off. Do not handle th[...]

E-7 Lithium-ion Battery Pack Danger Never use the Handheld Printer T erminal and its option including the battery pack and battery next to open fl ame, near a stove, or any other area exposed to high heat, or leave them for a long period of time in a vehicle parked in direct sunlight. Never use the battery pack with any device other than the Handh[...]

E-8 Power Supply / AC Adaptor W arning Do not use the Handheld Printer T erminal at a voltage other than the speci fi ed voltage. Also, do not connect the Handheld Printer T erminal to a multi-plug power strip. Never modify , sharply bend, twist, or pull on the power cord. Never use a detergent to clean AC adaptor and its power cable, especially o[...]

E-9 Operating Pr ecautions Y our Handheld Printer T erminal and its options are precision. Improper operation or rough handling can cause problems with data storage and other problems. Note and observe the following precautions to ensure proper operation. Do not leave dead battery pack in the Handheld Printer T erminal for a long period. Dead batte[...]

E-10 Lithium-ion Battery Pack Each lithium-ion battery pack has its life. The life span heavily depends on how the battery pack is charged or stored which may cause deterioration of the battery pack to shorten the life span if it is handled improperly . Note the tips below to make the battery pack last long. — Be sure to charge the battery pack b[...]

E-11 Important This guide does not include any information about programming and download procedures. See the applicable separate documentation for information about the procedures. After Service Should this product ever malfunction, contact your original retailer providing information about the product name, the date you purchased it, and details [...]

E-12 Regulatory Information The USA and Canada GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THIS UNIT IN THE U.S.A. (not applicable to other ar eas). NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection[...]

E-13 L ’ utilisation de ce dispositif est autorisée seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) I’ utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Caution Exposure to r[...]

E-14 Checking in the Box Please check the contents of the box before using the Handheld Printer T erminal for the fi rst time. Open the box and make sure that all the items shown here are included. Handheld Printer T erminal Neck Strap and Stylus Holder Stylus Hand Strap Roll Paper (80 mm) * User's Guide (this manual) Neck Strap Rings Battery[...]

E-15 Handheld Printer T erminal System Confi guration IT -9000 Series IT -9000E-MC25E IT -9000E-C25E These models are available in the USA and Canada only . USB Cradle HA-L60IO Ethernet Cradle HA-L62IO Cradle-type Battery Charger HA-L30CHG The illustration shows the USB Cradle (HA-L60IO). Car Mounted-type Battery Charger HA-L35CHG The car power ca[...]

E-16 Options AC Adaptor AD-S42120C-N5 AD-S42120B-N * Screen Pr otect Sheet HA-C90PS5B USB Cable (to connect cradle to PC) DT -380USB-A Power Cord for Eur ope AC-CORD-EU Power Cord for North America AC-CORD-US Power Cord for T aiwan AC-CORD-TW Power Cord for Kor ea AC-CORD-KR Power Cord for Australia AC-CORD-AU USB Cable (for client) HA-L81USBC USB [...]

E-17 General Guide Shapes vary according to model. Back Bottom Left Right Front To p 17 17 16 12 13 10 29 1 2 3 7 8 4 5 6 9 10 14 11 15 18 28 27 19 21 24 22 23 20 26 19 25 19 25[...]

E-18 1 Printer Prints when loaded with roll paper . 2 Splash Protect Cover A splash proof cover . Slide the cover open when printing. 3 Power Key T urns the power on and off. 4 Indicator 2 Flashes blue when operating via Bluetooth or orange when operating via W -LAN. Lights red when there is a bar code scanning error and lights green when a bar cod[...]

E-19 17 NFC Reader Apply a card here so that the card can be accessed. 18 Reset Switch Used to reset the Handheld Printer T erminal. 19 Hand Strap Hook*** Used to attach the handbelt to hold the terminal or to carry it. 20 Cradle Mount Holes These holes hold the terminal seating in the optional cradle or in the battery charger . 21 Extension Port P[...]

E-20 Keys 1 2 3 4 5 6 7 8 9 10 11 1 Function Keys These keys are used when starting a pre-registered application. 2 C (Clear) Key This key is pressed when canceling an operation and input. 3 BS (Backspace) Key This key is pressed when deleting the character to the left of the cursor . 4 ENT (Enter) Key This key is pressed when entering an input. 5 [...]

E-21 Loading and Removing the Battery Pack Y our Handheld Printer T erminal uses two types of battery: a battery pack and a memory backup battery . The battery pack is used to power normal operations and to store data, while the memory backup battery provides the power required to maintain memory contents when the battery pack power is unable to su[...]

E-22 Loading 1. T urn the terminal upside down. If the hand strap is fi tted to the terminal, remove it. 2. T urn the left and right lock switches for the battery pack cover to the “FREE” position, and then open the battery pack cover . 3. Hold the battery pack level so that the side with the terminals faces left and load it from directly abov[...]

E-23 Removing 1. Make sure that the Handheld Printer T erminal is turned off. If the power is on, press the power key to turn it off. 2. T urn the terminal upside down. If the hand strap is fi tted to the terminal, remove it. 3. T urn the left and right lock switches for the battery pack cover to the “FREE” position, and then open the battery [...]

E-24 Charging the Battery Pack Battery pack installed in the terminal can be charged using either cradle, battery char ger or AC adaptor (AD-S42120C-N5/AD-S42120B-N). Battery charge condition can be monitored with Indicator 1 on the terminal. Multiple battery packs can also be charged simultaneously using Dual Battery Charger . USB Cradle/Ethernet [...]

E-25 Dual Battery Charger T aking care that the battery pack is oriented correctly , insert it into the Dual Battery Charger . This causes the Charge Indicator LED to light in red, indicating that char ging has started. Y ou can connect up to three Dual Battery Chargers. Status of Charge Indicator LED Off: Not charging Red: Charging Red Flashing: B[...]

E-26 Handling the Hand Strap A hand strap can be attached to the Handheld Printer T erminal. Hook A Release buttons Hand Strap Hook B Attach the hand strap following the procedure described below . 1. Attach Hook B of the hand strap to the hand strap hook located on the bottom of the Handheld Printer T erminal. (On models with a magnetic card reade[...]

E-27 Handling the Neck Strap A neck strap can be attached to the Handheld Printer T erminal to keep it from being dropped while being carried. The stylus holder provided can also be attached. Neck strap Adjust length here Mounting hooks Stylus holde r Neck strap rings * Attach the neck strap following the procedure described below . Attaching 1. Pu[...]

E-28 Removing 1. Pull back the locking bar of the neck strap mounting hook and then release the hook from each ring as shown in the illustration. 2. Following the attachment procedure in reverse way , remove the neck strap rings from each neck strap mounting hook on the Handheld Printer T erminal and then push back the neck strap mounting hooks int[...]

E-29 2. Remove Mounting Hook C. 3. Pass the stylus holder through the strap as shown in the illustration. 4. Fold back the strap after passing through Bracket C, and then fasten in the same way it was originally fastened with Bracket A and Bracket B. Do not pass the strap through the stylus holder when folding it back. Place the stylus in the stylu[...]

E-30 Confi guring Handheld Printer T erminal Settings Calibrating T ouch Screen Alignment Whenever the response of the touch screen is poor , or operation being executed does not match with the location you are tapping on the touch screen, please recalibrate the alignment of the touch screen using the following method. Press the Fn key and then pr[...]

E-31 Setting the Display Brightness Adjusting Display Brightness Y ou can use the following procedures to adjust display brightness to make it easier to read under different lighting conditions. Press the Fn key and then press the “5” key or “6” key after con fi rming that “F” is displayed on the screen. Pressing the “5” key adjust[...]

E-32 Using the CMOS Imager (Imager Models) 1. T urn on the Handheld Printer T erminal, position its CMOS Imager reader port near the bar code or 2D code, and then press the trigger key . Shine the aimer on the bar code. IT -9000-GMC25E/25E/20E/G25E/ G20E/GC25E/MC25E/C25E Shine the aimer on the center of the bar code. IT -9000-GMC30E/GM35E/ GM30E 2.[...]

E-33 Using the Printer The printer can print on roll paper (80 mm or 58 mm wide).* Installing the Roll Paper 1. Check that the power is off. If the power is on, always make sure to turn it off by pressing the power key . 2. T urn the left and right printer cover lock switches to the "FREE" position to unlock the printer cover . 3. Open th[...]

E-34 5. Close the printer cover . T urn the left and right lock switches from the "UNLOCK" position to the "LOCK" position to lock the printer cover . T ear off the protruding roll paper . <About the Splash Protect Cover> When you are using the IT -9000 outdoors in the rain or in similar situations, slide the splash protec[...]

E-35 Attaching the 58 mm Paper Width Adjuster Attach the 58 mm Paper W idth Adjuster* inside the printer cover when using 58 mm wide roll paper . Refer to the procedure described in “Installing the Roll Paper” for information on opening and closing the printer cover . 1. Remove the 80 mm Paper W idth Adjuster as shown in the illustration. Store[...]

E-36 Precautions When Using Printer Printing Accuracy 1. During high-duty printing such as printing horizontal lines or printing while the battery remaining capacity is low , the printing speed may slow down to prevent excess current consumption that may cause unaligned printing for one dot or more. 2. Line change errors may occur if the printing i[...]

E-37 Others 1. The temperature range for printing with label paper is 5 to 35°C. 2. Once the end mark of the paper appears, pr omptly replace with new paper . 3. Recommended paper: Use only speci fi ed papers by CASIO. 4. Paper scraps may accumulate and printing quality may decr ease when the printer has been used for a long period of time. The t[...]

E-38 Handling SD Memory Car ds SD memory card can be installed in the SD memory card slot on the Handheld Printer T erminal. Install (or remove) an SD memory card according to the procedure described below . Installing 1. Open the cover of the SD memory card slot ( ) and insert an SD memory card all the way in until the top of the SD memory card al[...]

E-39 Handling SIM/SAM Car ds The Handheld Printer T erminal supports SIM cards and SAM cards. (The IT -9000- E/05E/05E-CN/20E/25E/IT -9000E-C25E/MC25E models only support SAM cards.) Since the SIM/SAM card slot is located inside the battery pack compartment, fi rst remove the battery pack when installing or removing a SIM/SAM card. Refer to pages [...]

E-40 6. Lay the SIM/SAM card cover down to close it and then slide it in the "Lock" direction. 7. Fit the slot cover . 8. Load the battery pack. Removing 1. Make sure that the power on the terminal has been switched off. If the power is still on, press the power key to switch off. 2. Remove the battery pack. 3. Using the tip of a screwdri[...]

E-41 5. Remove the SIM/SAM card. 6. Lay the SIM/SAM card cover down to close it and then slide it in the "Lock" direction. 7. Fit the slot cover . 8. Load the battery pack. Important! The type and number of cards inserted varies depending on model. Insert the cards in the correctly marked slots. A SIM/SAM card must be inserted with the to[...]

E-42 Handling Magnetic Car d Reader The Handheld Printer T erminal supports magnetic card reading. This function is not available on some models. See P .20 for information on models that support this function. Use the procedure below for magnetic card reading. 1. Insert the card at the end of the reader slot as shown in the illustration and then st[...]

E-43 Handling the NFC Reader/W riter NFC is a type of RFID (Radio Frequency Identi fi cation) technology that allows the data in a device to be read simply by holding the device up to an NFC reader . It can be used to read RFID tags used for controlling goods as well as contactless IC cards used in applications such as employee identi fi cation. [...]

E-44 Important! Both contactless IC cards and RFID tags The NFC employs a low power radio wave which does not r equire r egulatory station license. Frequency band used by the NFC is 13.56 MHz. Secur e a suf fi cient space between IT -9000 and other reader/writer located in the vicinity . Make sure also that a radio station employs the same frequen[...]

E-45 Performing Communications Bluetooth ® Communication Bluetooth ® interface can also be used to transfer data between two Handheld Printer T erminals. W ith Bluetooth ® the two Handheld Printer T erminals should be located within about three meters (9 '10 3 ⁄ 8 " ) from each other , as long as there is nothing blocking the path be[...]

E-46 GSM/W-CDMA Communication T o use the GSM/W -CDMA functions, you must receive service from a wireless service provider . A vailable GSM/W -CDMA functions may be dependent on the service provider to which you connect. Please consult your service provider for details about network service. If you use GSM/W -CDMA and WLAN at the same time, the com[...]

E-47 Resetting the Handheld Printer T erminal Resetting the terminal is the same as resetting a PC. Performing a reset causes all unsaved RAM data to be lost that are in mid-course of inputting and editing, but data and settings that are already stored in the FlashROM should be unaffected. Perform a reset to restore normal operation whenever the Ha[...]

E-48 1. Hold down power key and C key while pushing down the reset switch for about 3 seconds with the tip of a stylus until the message shown below appears on the display . T o cancel the full reset operation, press L Program key . R Program key 2. Press R Program key . This causes the message shown below to appear . T o cancel the full reset oper[...]

E-49 W ar ning Label W ar ning! (IT -9000-20E/25E/G20E/G25E/GC25E/GMC25E/IT -9000E- C25E/MC25E) ■ Never look directly into the laser light. These products scan using laser light. Never look directly into the laser light or shine the laser light into the eyes. This label is a warning and caution label for Class 2 laser products that comply with IE[...]

E-50 IT -9000 Specifi cations Model: IT -9000-05E/E/05E-CN/G05E/GE/GMC25E/GMC30E/25E/20E/ G25E/G20E/GC25E/GM35E/GM30E IT -9000E-MC25E/C25E CPU: Marvell ® PXA320 624MHz Memory: Windows CE: 256MB RAM, 256MB Flash ROM (user de fi ned: 176MB) W indows mobile:256MB RAM, 256MB Flash ROM (user de fi ned: 130MB) OS: Microsoft W indows CE 6.0R3 operatin[...]

E-51 Bluetooth ® : Protocol: Bluetooth ® Speci fi cation V er .2.0 + EDR Communication Range: Approximately 3 m (9'10 3 / 8 ") (depends on radio wave conditions and environment) Output: 4dBm max. (PowerClass2) WLAN: Standards: IEEE 802.1 1b/g Diffusion Modulation: DS: 802.1 1b DS/OFDM: 802.1 1g Frequency: 802.11b/g: 2.400-2.4835 GHz Tr[...]

E-52 No. of channels: GSM 850: 124 GSM 900: 174 GSM1800 (DCS1800): 374 GSM1900 (PCS1900): 299 Channel space: 200 KHz Channel bandwidth: 200 KHz Output: GSM 850: 32 dBm GSM 900: 32 dBm GSM1800 (DCS1800): 29 dBm GSM1900 (PCS1900): 29 dBm W -CDMA: Standard: UMTS/W -CDMA: 3GPP release 99 HSDP A: 3GPP release 5 Communication functions : V oice sound, ci[...]

E-53 Sensitivity: Acquisition sensitivity: -141 dBm Tracking sensitivity: -158 dBm SIM card: Standard: ISO 7816 IC Card standard General speci fi cations: Support for 3 V and 1.8 V SIM cards SAM card: Standard: ISO 7816 IC Card standard General speci fi cations: Support for 1.8 V , 3 V and 5 V SAM cards Camera (IT -9000-GMC25E/GMC30E/GC25E/IT -90[...]

E-54 IT -9000-G25E/G20E: Approximately 625g (22.0oz) (with battery pack installed, not including roll paper) IT -9000-GC25E: Approximately 630g (22.2oz) (with battery pack installed, not including roll paper) IT -9000E-MC25E: Approximately 655g (23.1oz) (with battery pack installed, not including roll paper) IT -9000-GMC25E: Approximately 675g (23.[...]

E-55 Dimensional Drawings IT -9000-05E/E/05E-CN/G05E/GE Approx. 11 1.9mm (4 3 / 8 ") Approx. 59.7mm (2 3 / 8 ") Approx. 36.6mm (1 7 / 16 ") Approx. 246.3mm (9 11 / 16 ") Approx. 78.2mm (3 1 / 16 ") IT -9000-25E/20E/G25E/G20E/GC25E/C25E Approx. 253.6mm (10") Approx. 78.2mm (3 1 / 16 ") Approx. 36.6mm (1 7 / 16 &quo[...]

E-56 IT -900-GMC25E/GMC30E/GM35E/GM30E/MC25E Approx. 65.8mm (2 9 / 16 ") Approx. 283.7mm (11 3 / 16 ") Approx. 36.6mm (1 7 / 16 ") Approx. 78.2mm (3 1 / 16 ") Approx. 11 1.9mm (4 3 / 8 ")[...]

E-57 Using the USB Cradle (HA-L60IO) The optional USB Cradle (HA-L60IO) makes it possible to transmit system data and fi le data between the Handheld Printer T erminal and a PC via a USB connection (download or upload). Y ou can also use the USB Cradle to charge the battery pack installed in the Handheld Printer T erminal. General Guide Left T op [...]

E-58 1 T erminal Detect Switch This switch detects when the IT -9000 is mounted correctly on the USB Cradle. 2 Mount Hooks These hooks are used to stabilize the IT -9000 when mounting it on the cradle. 3 Removal Buttons Press when removing the IT -9000. 4 Power Supply/Data Communication T erminals Power is supplied to the IT -9000 via these contact[...]

E-59 Connecting the USB Cradle Power Supply Use the optional AC adaptor (AD-S42120C-N5/AD-S42120B-N) for the power supply of the USB Cradle. Always make sure to connect the AC adaptor to the USB Cradle before performing communication with the Handheld Printer T erminal. Power to the Handheld Printer T erminal is supplied from the USB Cradle. 1. Plu[...]

E-60 4. Before using the cradle ports, remove the caps from the ports. Connect one end of the USB cable (DT -380USB-A) to the USB client port and the other end to the PC. The USB host port is used for connecting the cradle with other USB peripheral device. PC USB peripheral device 5. T urn on the power switch on the right side of the USB Cradle. Th[...]

E-61 Status of Indicator 1 on IT -9000: Orange: Charging the battery pack. Red Flashing: Standby due to battery pack error or the surrounding temperature is out of the charging temperature range. (charging begins when the temperature is within the char ging temperature range) Green: Charging the battery pack is complete. Status of Indicator 2 on IT[...]

E-62 Specifi cations 1. LAN Speci fi cations Communications protocol: IEEE 802.3 Media type: 10base-T/100base-TX auto-switched 2. USB Protocol: USB V er1.1 Standard T ransmission Rate: 12Mbps (max.) 3. Charging Charging Method: Constant current/voltage (the charging circuit is built in IT -9000) Charge Period: Approximately 5 hours 4. Power Suppl[...]

E-63 Using the Ether net Cradle (HA-H62IO) The optional Ethernet Cradle (HA-H62IO) makes it possible to transmit system data and fi le data between the Handheld Printer T erminal and a PC via a USB or LAN connection (download or upload). Y ou can also use the Ethernet Cradle to charge the battery pack installed in the Handheld Printer T erminal. G[...]

E-64 1 T erminal Detect Switch This switch detects when the IT -9000 is mounted correctly on the Ethernet Cradle. 2 Mount Hooks These hooks are used to stabilize the IT -9000 when mounting it on the cradle. 3 Removal Buttons Press when removing the IT -9000. 4 Power Supply/Data Communication T erminals Power is supplied to the IT -9000 via these co[...]

E-65 Connecting the Ethernet Cradle Power Supply Use the optional AC adaptor (AD-S42120C-N5/AD-S42120B-N) for the power supply of the Ethernet Cradle. Always make sure to connect the AC adaptor to the Ethernet Cradle before performing communication with the Handheld Printer T erminal. Power to the Handheld Printer T erminal is supplied from the Eth[...]

E-66 4. Before using the cradle ports, remove the caps from the ports. When using a LAN, connect one end of the LAN cable to the LAN port and the other end to the PC or hub. When using a USB connection, connect one end of the USB cable (DT -380USB-A) to the USB port and the other end to the PC. The USB host port is used for connecting the cradle wi[...]

E-67 Status of Indicator 1 on IT -9000: Orange: Charging the battery pack. Red Flashing: Standby due to battery pack error or the surrounding temperature is out of the charging temperature range. (charging begins when the temperature is within the char ging temperature range) Green: Charging the battery pack is complete. Status of Indicator 2 on IT[...]

E-68 Specifi cations 1. LAN Speci fi cations Communications protocol: IEEE 802.3 Media type: 10base-T/100base-TX auto-switched 2. USB Protocol: USB V er1.1 Standard T ransmission Rate: 12Mbps (max.) 3. Charging Charging Method: Constant current/voltage (the charging circuit is built in IT -9000) Charge Period: Approximately 5 hours 4. Power Suppl[...]

E-69 Using the Cradle-type Battery Charger (HA-L30CHG) The optional Cradle-type Battery Charger (HA-L30CHG) makes it possible to char ge the battery pack installed in the Handheld Printer T erminal. General Guide Left 3 To p 1 3 3 5 4 2 2 Right 3 6 Back 7[...]

E-70 1 T erminal Detect Switch This switch detects when the IT -9000 is mounted correctly on the charger . 2 Mount Hooks These hooks are used to stabilize the IT -9000 when mounting it on the charger . 3 Removal Buttons Press when removing the IT -9000. 4 Power Supply T erminals Power is supplied to the IT -9000 via these contacts. 5 Power Indicato[...]

E-71 Connecting the Cradle-type Battery Charger Power Supply Use the optional AC adaptor (AD-S42120C-N5/AD-S42120B-N) for the power supply of the Cradle-type Battery Charger . 1. Plug the AC adaptor into the AC adaptor jack on the back of the Cradle-type Battery Charger . 2. After connecting the power cable to the AC adaptor, plug the other end of [...]

E-72 4. Push the IT -9000 fully into the Cradle-type Battery Charger until the mount hooks in the charger engage the mount holes in the IT -9000. Check that the power LED on the top of the Cradle-type Battery Charger lights green and that indicator 1 on the IT -9000 lights. T o remove the IT -9000 from the Cradle-type Battery Charger , push the rem[...]

E-73 Specifi cations 1. Charging Charging Method: Constant current/voltage Charge Period: Approximately 5 hours 2. Power Supply Power Source: AC adaptor (AD-S42120C-N5/AD-S42120B-N*) Consumption Current: 12V DC approximately 3.5A Output to Handheld Printer T erminal : 12V DC 3.5A (max.) 3. AC Adaptor Model: AD-S42120C-N5/AD-S42120B-N Input: 100V t[...]

E-74 Using the Car Mounted-type Battery Charger (HA-L35CHG) The optional Car Mounted-type Battery Charger (HA-L35CHG) can be used to char ge the battery installed in the Handheld Printer T erminal using power from the cigarette lighter in your car . General Guide Left 3 To p 1 3 3 5 4 2 2 Right 3 6 Back 1 T erminal Detect Switch This switch detects[...]

E-75 Connecting the Car Mounted-type Battery Charger Power Supply Use the cigarette lighter socket in the vehicle for the power supply of the Car Mounted- type Battery Charger . 1. Plug the small plug of the bundled Car Power Cable into the car adaptor jack on the back of the Car Mounted-type Battery Charger . 2. Plug the cigarette lighter plug of [...]

E-76 Status of Indicator 1 on IT -9000: Orange: Char ging the battery pack. Red Flashing: Standby due to battery pack error or the surrounding temperature is out of the charging temperature range. (charging begins when the temperature is within the char ging temperature range) Green: Charging the battery pack is complete. Important! Allowing the po[...]

E-77 Specifi cations 1. Charging Charging System: Constant current/voltage Charge time: Approximately 5 hours 2. Dimensions and W eight Dimensions: Approximately 129(W) × 262(D) × 82(H) mm (5 1 ⁄ 16 "W × 10 5 ⁄ 16 "D × 3 1 ⁄ 4 "H) W eight: Approximately 544g (19.2oz) 3. Operating Environment T emperature: 0°C to 40°C (32[...]

E-78 Using the Dual Battery Charger (HA-G32DCHG) The optionally available Dual Battery Charger (HA-G32DCHG) can be used to simultaneously charge two battery packs. General Guide 4 Left 1 2 To p Right 3 4 Bottom 5 Bundled Items Connection Bracket 2 screws[...]

E-79 1 Charge Indicator LED This LED indicates the charge status of the battery pack(s). Off: Not char ging Red: Charging Red Flashing: Battery pack problem Green Flashing: Standby Green: Charging complete 2 Power Contacts Power is supplied to the battery packs via these contacts. 3 AC Adaptor Jack This is used to supply power by connecting the AC [...]

E-80 Charging Battery Pack Use the separately sold AC adaptor (AD-S42120C-N5/AD-S42120B-N) for the power supply of the Dual Battery Charger . 1. Plug the cord from the AC adaptor into the AC adaptor jack of the Dual Battery Charger . 2. Plug the AC cord into a wall outlet. 3.T aking care that the battery pack is oriented correctly , insert it into [...]

E-81 Connecting Multiple Dual Battery Chargers Y ou can connect up to three Dual Battery Chargers. Doing so makes it possible to supply power to all the Dual Battery Chargers using one dedicated AC adaptor . 1. As shown in the illustrations below , remove the connector covers of the Dual Battery Chargers you want to connect to each other . Connecto[...]

E-82 Specifi cations 1. Charging Speci fi cation Charging Method: Constant current/voltage Charge Period: Approx. 4 hours (1 battery pack, normal temperature) When charging two battery packs: Approx. 5.5 hours (2 battery packs, normal temperature) 2. Power Supply Power Source: AC adaptor (AD-S42120C-N5/AD-S42120B-N) Consumption Current: 12V DC 3.[...]

E-83 Using the Rechargeable Battery Pack (HA-G20BA T) HA-G20BA T Important! Store a battery pack in its special soft case whenever you are not using it. If the battery pack has been left over unused for a long period of time, the capacity remained decr eases due to spontaneous discharge or chemical decomposition by the battery pack itself. If the b[...]

CASIO COMPUTER CO., L TD. 6-2, Hon-machi 1-chome Shibuya-ku, T okyo 151-8543, Japan 2012 CASIO COMPUTER CO., L TD.[...]