Dodge 2005 Ram 2500 manual

T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE .............................. 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE .............................. 7 3 4 UNDERST ANDING YOUR INSTRUMENT P ANEL ...................................[...]

[...]

INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 A Message From DaimlerChrysler Corporation . . . 5 䡵 How T o Use This Manual .................. 5 䡵 W arnings And Cautions ................... 6 䡵 V an Conversions/Campers ................. 6 䡵 V ehicle Identification Number ............... 7 䡵 V ehicle Modifications[...]

INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents. Y ou are urged to read these publications car efully . Following the instruc- ti[...]

A MESSAGE FROM DAIMLERCHR YSLER CORPORA TION DaimlerChrysler Corporation and Cummins welcome you as a new Dodge Ram Cummins T urbo Diesel- powered tr uck owner . Almost 100% of the heavy duty trucks in the United States are diesel power ed because of the fuel economy , rugged durability , and high torque which permits pulling heavy loads. Cummins e[...]

W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entir e manual you may miss important information. Observe all W arnings and Cautions. V AN CONVER[...]

VEHICLE IDENTIFICA TION NUMBER The vehicle identification number (VIN) is found on a stamped plate located on the left front corner of the instrument panel pad, visible fr om outside of the vehicle through the windshield. This number also appears on the Automobile Information Disclosure Label af fixed to a window on your vehicle. Save this label fo[...]

VEHICLE MODIFICA TIONS / AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. 8 INTRODUCTION[...]

THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys .................. 1 1 ▫ Key-In-Ignition Reminder ................ 1 1 ▫ Sentry Key — If Equipped ................ 1 1 䡵 Ignition And Steering Lock ................. 1 4 ▫ Manual T ransmissions ................... 1 4 ▫ Automatic T ransmissions .........[...]

▫ T o Set The Alarm ...................... 2 9 ▫ T o Disarm The System ................... 3 0 䡵 W indows ............................. 3 1 ▫ Power W indows—If Equipped ............. 3 1 ▫ Sliding Rear W indow—If Equipped ......... 3 2 ▫ W ind Buffeting ........................ 3 3 䡵 Occupant Restraints ...................... 3 3 [...]

A WORD ABOUT YOUR KEYS The double sided keys may be inserted into the locks with either side up. The keys for your new vehicle are enclosed in a plastic bag with a bar code label affixed to the front. The bar code can be used to or der duplicate keys from your dealer or a locksmith. If you r eceived your keys without the bag, ask your dealer to giv[...]

The ⬙ Security Light ⬙ , located in the instrument cluster , will illuminate for about 2 seconds when the ignition switch is first turned to the ON position. If the vehicle electronics do not r eceive a valid signal from the ignition key , the ⬙ Security Light ⬙ will flash continuously to signal that the vehicle has been immobilized. If the[...]

Customer Key Programming Y ou can program new keys to the system if you have two valid keys by doing the following: 1. Insert the first valid key into the ignition and turn the ignition to the ON position for at least 3 seconds but no longer than 15 seconds. T urn the ignition back to the OFF position and remove the first key . 2. Insert the second[...]

IGNITION AND STEERING LOCK Insert the key fully , and then turn the switch to one of the five illustrated positions. The key can be inserted or withdrawn only in the LOCK position. Manual T ransmissions When the steering wheel is in the LOCK position, the steering and ignition systems are locked to pr ovide antitheft protection for your vehicle. It[...]

Automatic T ransmissions In the LOCK position, the steering and ignition systems are locked to pr ovide antitheft protection for your ve- hicle. It may be difficult to turn the key fr om the LOCK position when starting your vehicle. Move the steering wheel left and right while turning the key until it turns easily . The key can be inserted or withd[...]

DOOR KEY The same key used to start the vehicle is also used to unlock the doors. T o unlock the vehicle doors, insert the key into the lock and turn. T o lock the doors, insert the key and turn. DOOR LOCKS Manual Locks Front and Rear doors may be locked, by moving the lock plunger up or down. All doors may be opened with the inside door handle wit[...]

Power Door Locks — If Equipped NOTE: V ehicles equipped with remote keyless entry do not have a passenger side door lock cylinder . V ehicles equipped with power door locks can be locked or unlocked from inside by either the use of the door lock switches located on the front doors or by pr essing the LOCK or UNLOCK buttons on the Remote Keyless E[...]

As a safety feature the doors will not lock when using the door lock switches during the following condition: 1. The driver’s door is open while the key is in the ignition. Central Locking — If Equipped V ehicles with security will have a feature called ⬙ Central Locking ⬙ . When the key is placed in the door cylinder and turned to the ⬙ [...]

Automatic Door Locks If this feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph. This feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedur e: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt (Fastening the sea[...]

This feature will not operate if any of the conditions above are not met or following has occurr ed: • Any manual operation of a door lock switch has occurred. Auto Unlock Feature Programming This feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedur e: Customer Programming seq[...]

Child Protection Door Lock T o provide a safer envir onment for children riding in the rear seat, the r ear doors of your vehicle have the child- protection door lock system. T o use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child-protection locks. When the system on a door is engaged, th[...]

W ARNING! A void trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position. NOTE: For emergency exit with the s[...]

T o unlock the doors: Press and r elease the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors. When the UNLOCK button is pressed, the illuminated entry will initiate, the parking lights will flash on twice and if installed, the cargo lamp will turn on for 30 seconds. The system can be programmed [...]

T o lock the doors: Press and r elease the LOCK button on the transmitter to lock all doors. If the ignition is OFF , when the doors are locked, the parking lights will flash on once and the horn will chirp once. The horn chirp feature will be shipped fr om the assembly plants activated. If desired this featur e can be disabled by using the followi[...]

2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may confuse you during this program- ming procedur e). 3. Place the key into the ignition. 4. T urn the ignition to the ON position ( Do not start the engine ). 5. Press and hold the LOCK button on a programmed (i.e. functional) key fob. 6. Continue to hold the LOCK butt[...]

door locks and remote keyless entry systems will func- tion normally . Panic mode will not disarm the security system on vehicles so equipped. Programming Additional T ransmitters V ehicles with the keyless entry option will be shipped from the assembly plants with two key fob transmitters programmed only for that vehicle. A total of four fobs can [...]

9. A single chime will be heard. The chime indicates that the fob has been recognized. 10. W ithin 4 seconds of hearing the chime, press and release any button on the fob being pr ogrammed. 1 1. A single chime will be hear d. The chime indicates that the fob has been programmed. 12. Repeat steps 8 to 1 1 for a total of 4 fobs. 13. T urn the ignitio[...]

2. Closeness to a radio transmitter such as a radio station tower , airport transmitter , and some mobile or CB radios. T ransmitter Battery Service The recommended r eplacement battery is a 3V lithium 2016 cell. This transmitter requir es two batteries. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit bo[...]

SECURITY ALARM SYSTEM — IF EQUIPPED This system monitors the vehicle doors and ignition for unauthorized operation. When the alarm is activated, the system provides both audible and visual signals. For the first 3 minutes the horn will sound and the headlights and security telltale will flash repeatedly . For an addi- tional 15 minutes only the h[...]

T o Disarm the System: Use the Keyless Entry transmitter or the key to turn the driver’s door lock to the unlock position. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors and the security lamp will flash for 30 seconds. Check the vehicle for tampering. The Security system will also [...]

WINDOWS Power Windows—If Equipped The control on the left fr ont door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window contr ol and on the rear doors of Quad Cab models. The windows will operate only when the ignition swit[...]

Auto Down (Driver’s Side Only) The driver’s window switch has an Auto Down feature. Press the window switch past the detent, r elease, and the window will go down automatically . W indow Lockout Switch (4 Door Models Only) The window lockout switch on the driver’s door allows you to disable the window control on the other doors. T o disable t[...]

WIND BUFFETING W ind buffeting can be described as the perception of pressur e on the ears or a helicopter type sound in the ears. Y our vehicle may exhibit wind buffeting with the windows down or partially open positions. This is a normal occurrence and can be minimized. If the buf feting occurs with the rear windows open, open the fr ont and rear[...]

Research has shown that seat belts save lives, and that they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown fr om the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belte[...]

W ARNING! • W earing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body . These are the strongest parts of your body and can take the forces of a collision the best. W earing your belt in the wrong place could make your injuries in a collision much worse. Y ou might suffer internal injuries, or[...]

plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” W ARNING! • A belt buckled into the wrong buckle will not protect you properly . The lap portion could ride too [...]

4. Position the lap belt across your thighs, below your abdomen. T o remove slack in the lap belt portion, pull up on the shoulder belt. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. W ARNING! • A lap belt worn too high can increase[...]

6. T o release the belt, push the r ed button on the buckle. The belt will automatically retract to its stowed position. If necessary , slide the latch plate down the webbing to allow the belt to retract fully . W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically , ch[...]

2. T o reattach the seat belt to the fr ont center seat, pull the black buckle latch plate forward fr om the cab back panel and insert it into the black keyed buckle until there is an audible click. Refer to the previous section for the proper seat belt usage. W ARNING! • If the black latch and black buckle are not prop- erly connected when the s[...]

Inserting Latch Plate In Use Position 40 THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE[...]

W ARNING! If the black latch and buckle are not connected when the seat belt is used by an occupant, the seat belt will not restrain you properly . Adjustable Upper Shoulder Belt Anchorage In the front r ow outboard seats, the shoulder belt can be adjusted upward or downwar d to help position the belt away from your neck. Pr ess the button located [...]

Automatic Locking Mode (if Equipped) In this mode, the shoulder belt is automatically pre- locked. The belt will still retract to r emove any slack in the shoulder belt. The automatic locking mode is only available on the front passenger side belt. When T o Use The Automatic Locking Mode Anytime a child safety seat is installed in a passenger front[...]

W ARNING! • A lap belt worn too loose or too high is dangerous. • A belt worn too loose can allow you to slip down and under the belt in a collision. • A belt that is too loose or too high will apply crash forces to the abdomen, not to the stronger hip bones. In either case, the risk of internal injuries is greater . W ear a lap belt low and [...]

Enhanced W arning System (BeltAlert) will be reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). The Enhanced W arning System (BeltAlert) can be en- abled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the [...]

Seat Belts and Pregnant Women W e recommend that pr egnant women use seat belts throughout their pr egnancies. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug against the hips as possible. Keep the belt low so that it does not come across the abdomen. T[...]

These airbags are certified to the new Federal r egulations that allow less forceful deployments. This vehicle may also be equipped with window bags to protect the driver and passengers in the first and second row sitting next to a window . If the vehicle is equipped with window bags, they are located above the side windows. Their covers are also l[...]

Airbags inflate in moderate to high speed impacts. Along with the seatbelts, front airbags work with the instr ument panel knee bolsters to provide impr oved protection for the driver and front passenger . W indow bags also work with seat belts to improve occupant pr otection. The seat belts are designed to pr otect you in many types of collisions.[...]

• The driver and front passenger seats should be moved back as far as practical to allow the airbag room to inflate. W ARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly . In some collisions the airbags won’t deploy at all. Always wear your se[...]

The W indow Airbag System, on vehicles equipped, consists of the following: • AIRBAG Readiness Light (shared with the fr ont airbag system) • W indow Bags Above the Side W indows. • Airbag Control Module (shar ed with the front airbag system) • Side impact sensors • Interconnecting W iring How The Airbag System W orks • The airbag contr[...]

• If it detects a malfunction in any part of the system, it turns on the light either momen- tarily or continuously . The instrument cluster will flash the seat belt indicator if it detects a fault with the airbag indicator . W ARNING! Ignoring the AIR BAG light in your instrument panel could mean you won’t have the airbags to protect you in a [...]

Passenger Airbag On/Off Switch – (Standard Cab V ehicles Only) The passenger front airbag is to be turned of f only if the passenger: • is an infant (less than 1 year old) who must ride in the front seat because ther e is no rear seat, because the r ear seat is too small for a rear -facing infant restraint or because the infant has a medical co[...]

W ARNING! Whenever an airbag is turned off, even a lap/ shoulder belted passenger may hit their head, neck, or chest on the dashboard (instrument panel) or windshield in a crash. This may result in serious injury or death. T o Shut Off the Passenger Airbag (Standard Cab V e- hicles Only) Place the ignition key in the Passenger Airbag On/Off Switch,[...]

If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and fr ont passenger as the airbags deploy and unfold. The abrasions are similar to friction r ope burns or those you might get sliding along a carpet or gymna[...]

W indow Airbags Supplemental Restraint System (SRS)—If Equipped The window airbag control module determines if a side collision is severe enough to r equire the side airbags to inflate. The window airbag control module will not detect roll over , front or r ear collisions. The airbag control module monitors the r eadiness of the electronic parts [...]

Maintaining Y our Airbag Systems W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right[...]

NOTE: If the speedometer , tachometer or any engine related gauges ar e not working, the airbag control mod- ule may also be disabled. The airbags may not be ready to inflate for your protection. Pr omptly check fuse num- bers 52 and 53 in the fuse and relay center . See your dealer if the fuse is good. Child Restraint Everyone in your vehicle need[...]

of child restraints can be used r earward-facing: infant carriers and ⬙ convertible ⬙ child seats. Both types of child restraints ar e held in the vehicle by the lap/ shoulder belt. • The infant carrier is only used rearwar d-facing in the vehicle. It is recommended for childr en who weigh up to about 20 lbs (9 kg). ⬙ Convertible ⬙ child [...]

W ARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. • A rearward facing child restraint should only be used in a rear seat, or in the fr[...]

which are designed to keep the lap portion tight around the child r estraint so that it is not necessary to use a locking clip. If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight, however , any seat belt system will loosen [...]

• When your child restraint is not in use, secur e it in the vehicle with the seat belt or remove it fr om the vehicle. Do not leave it loose in the vehicle. In a sudden stop or collision, it could strike the occupants or seat backs and cause serious personal injury . W ARNING! Improper installation can lead to failure of an infant or child restr[...]

Standard Cab Passenger Seat Quad Cab Outboard Seat THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE 61 2[...]

Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seatback tether anchorage have been available for some time. In fact, many child restraint manufactur ers will provide add-on tether strap kits for some of their older produc[...]

rearwar d-facing infant restraints will also be equipped with a tether strap, a hook and means for adjusting the tension in the strap. In general, you will first loosen the adjusters on the lower straps and tether straps so that you can more easily attach the hook or connector to the lower anchorages and tether anchorages. Then tighten all three st[...]

W ARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle. Use only the anchor positions directly behind the child seat to secure a child restraint top[...]

Multiple Child Restraint Installation Sequence - (Quad Cab Rear Seats) 1. Obtain tether straps by raising the head restraints and reaching between the r ear glass and rear seat. The tether strap may be retained with an elastic band. Accessibility to the tether strap is greatly impr oved by raising the seat cushion to the “up” position. Remove t[...]

Multiple Child Restraints 66 THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE[...]

Children T oo Large for Booster Seats Children who ar e large enough to wear the shoulder belt comfortably , and whose legs are long enough to bend over the front of the seat when their back is against the seat back should use the lap/shoulder belt in a rear seat. • Make sure that the child is upright in the seat. • The lap portion should be lo[...]

• Check the coolant and oil levels frequently . • V ary throttle position at highway speeds when carry- ing or towing significant weight. Because of the construction of the Cummins Diesel engine, engine run-in is enhanced by loaded operating conditions which allow the engine parts to achieve final finish and fit during the first 6,000 miles (10[...]

Lock Y our V ehicle Always remove the keys fr om the ignition and lock all doors when leaving the vehicle unattended, even in your own driveway or garage. T ry to park your vehicle in a well-lighted area and never invite theft by leaving ar - ticles of value exposed. Exhaust Gas W ARNING! Exhaust gases contain carbon monoxide, a poten- tially toxic[...]

Safety Checks Y ou Should Make Inside The V ehicle Seat Belts Inspect the belt system periodically , checking for cuts, frays and loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor , torn webbing, etc.) o[...]

Door Latches Check for positive closing, latching and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, water , oil, or other fluid leaks. Also, if fuel fumes ar e detected the cause should be located and corrected. THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE 71 2[...]

[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors ............................... 7 8 ▫ Inside Mirror ......................... 7 8 ▫ Automatic Dimming Mirror— If Equipped .... 7 9 ▫ Outside Mirrors ....................... 7 9 ▫ Exterior Mirrors Folding Featur e ........... 8 0 ▫ Electronic Power Mirr ors — If Equipped[...]

䡵 Seats ................................ 1 0 6 ▫ 40-20-40 Front Seat .................... 1 0 7 ▫ Reclining Seats ....................... 1 0 8 ▫ Adjustable Head Restraints .............. 1 0 8 ▫ Manual Rotary Lumbar Support Adjustment — If Equipped .............. 1 0 9 ▫ Power Seats — If Equipped .............. 1 1 0 ▫ Heated Sea[...]

䡵 Driver Adjustable Pedals — If Equipped ...... 1 2 3 ▫ Adjustment ......................... 1 2 3 䡵 Electronic Speed Contr ol — If Equipped ...... 1 2 4 ▫ T o Activate .......................... 1 2 4 ▫ T o Set At A Desir ed Speed ............... 1 2 5 ▫ T o Deactivate ........................ 1 2 5 ▫ T o Resume Speed ...........[...]

䡵 Garage Door Opener — If Equipped ......... 1 3 4 ▫ Programming Homelink ................ 1 3 6 ▫ Canadian Programming/Gate Pr ogramming . . 138 ▫ Using Homelink ...................... 1 3 9 ▫ Erasing Homelink Buttons ............... 1 3 9 ▫ Reprogramming a Single Homelink Button . . . 140 ▫ Security ............................ 1 [...]

▫ Storage And Seats — If Equipped .......... 1 4 8 䡵 Fold Flat Load Floor — If Equipped ......... 1 4 8 ▫ Fold Flat Load Floor — If Equipped ........ 1 4 8 䡵 Pickup Box ........................... 1 5 1 䡵 Slide-In Campers ....................... 1 5 3 ▫ Camper Applications ................... 1 5 3 䡵 Easy-Off T ailgate .........[...]

MIRRORS Inside Mirror The mirror should be adjusted to center on the view through the r ear window . Annoying headlight glare can be r educed by moving the small control under the mirr or to the night position (toward r ear of vehicle). The mirror should be adjusted while set in the day position (toward windshield). 78 UNDERST ANDING THE FEA TURES [...]

Automatic Dimming Mirror— If Equipped This mirror automatically adjusts for annoying headlight glare fr om vehicles behind you. Y ou can turn the feature on or off by pr essing the button at the base of the mirror . A light in the button will indicate when the dimming feature is activated. CAUTION! T o avoid damage to the mirror during cleaning, [...]

W ARNING! V ehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with an- other vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side convex mir[...]

Set the top switch to the left or right for the left or right mirror , and set it to the center off position to pr event accidentally moving a mirror when you ar e finished adjusting the mirror . T o adjust a mirror , select left or right with the top switch, and press one of the four arr ows for the direction you want the mirr or to move. Electric[...]

NOTE: Fold th e7x1 0 inch trailer towing mirrors rearward prior to entering an automated car wash. CAUTION! Do not attempt to fold th e7x1 0 inch trailer towing mirrors forward. Th e7x1 0 inch trailer towing mirrors are not designed to be folded forward and doing so will damage the mirrors and/or vehicle. 82 UNDERST ANDING THE FEA TURES OF YOUR VEH[...]

HANDS–FREE COMMUNICA TION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone* using simple voice commands (e.g., ⬙ Call ѧ Mike ѧ W ork ⬙ or ⬙ Dial ѧ 248-555-1212 ⬙ ). Y our cellular phone’s audio is transm[...]

UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s micro- phone for private conversation. The UConnect™ phonebook enables you to store up to 32 names and four numbers per name. Each language has a separate 32 name phonebook accessible only i[...]

The UConnect™ system can be used with any Hands- Free Pr ofile certified Bluetooth™ cellular phone. If your cellular phone supports a differ ent profile (eg., Headset Profile), you may not be able to use any UConnect™ features. Refer to your cellular service pr ovider or the phone manufacturer for details. The UConnect™ system is fully inte[...]

For example, you can either use the combined form voice command ⬙ Phonebook New Entry , ⬙ or you can break the combined form command into two voice commands: ⬙ Phonebook ⬙ and ⬙ New Entry . ⬙ Please re- member , the UConnect™ system works best when you talk in a normal conversational tone, as if speaking to some one sitting eight feet[...]

The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Phone Pairing. ⬙ • When prompted, after the voice on beep, say ⬙ Pair a Phone. ⬙ • Y ou will be asked to say a four-digit pin number which you will [...]

Dial by Saying a Number • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Dial. ⬙ • System will prompt you to say the number you want call. • For example, you can say ⬙ 234-567-8901. ⬙ The phone number that you enter must be of valid length and combination. The UConnect™ limits[...]

Add Names to Y our UConnect™ Phonebook NOTE: Adding names to phonebook is recommended when vehicle is not in motion. • Press the “Phone” button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Phonebook New Entry . ⬙ • When prompted, say the name of the new entry . Use of long names helps the voice recognitio[...]

• Y ou will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, mobile, or pager) that you wish to edit. • When prompted, r ecite the new phone number for the phonebook entry that you are editing. After you are finished editing an entry in the phonebook, you will be given[...]

After confirmation, the phonebook entries will be de- leted. Note that only the phonebook in the current language is deleted. Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Phonebook Erase All. ⬙ • The UConnect™ system will ask you t[...]

Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the UConnect™ system will interrupt the vehicle audio system, if on, and will ask if you would like to answer the call. T o reject the call, pr ess and hold the ’Phone’ button until you hear a single beep indicating that the incom[...]

T oggling Between Calls If two calls are in pr ogress (one active and one on hold), press the ’Phone’ button until you hear a single beep indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at one time. Conference Call When two calls are in pr ogress (one active and one on hold), press [...]

Call Continuation Call continuation is progr ession of a phone call on UConnect™ system after the vehicle ignition key has been switched to off. Call continuation functionality available on the vehicle can be any one of three types: • After ignition key is switched off, a call can continue on the UConnect™ system either until the call ends or[...]

Emergency Assistance If you are in an emer gency and the mobile phone is reachable: • Pick up the phone and manually dial the emergency number for your area. If the phone is not reachable and the UConnect™ system is operational, you may reach the emer gency number as follows: • Press the ’Phone’ button to begin. • After the ⬙ Ready ?[...]

Please refer to the 24-Hour T owing Assistance coverage details in the DaimlerChrysler Corporation 24-Hour T owing Assistance Program Guide. Paging T o learn how to page, refer to section ⬙ W orking with Automated Systems. ⬙ Paging works properly except for pagers of certain companies which time-out a little too soon to work properly with the U[...]

Barge In - Overriding Prompts The ’V oice Recognition’ button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately . For example, if a prompt is playing ⬙ W ould you like to pair a phone, clear a ѧ , ⬙ you could press the ’V oice Recognition’ button and say ⬙ Pair a Phone ⬙ to sele[...]

may feel that the call did not go through even though the call is in progr ess. Once your call is answered, you will hear the audio. Mute/Un-mute (Mute off) When you mute the UConnect™ system, you will still be able to hear the conversation coming from the other party , but the other party will not be able to hear you. In order to mute the UConne[...]

If you would like to connect or disconnect the Blue- tooth™ connection between a UConnect™ paired cellular phone and the UConnect™ system, follow the instruction described in your cellular phone user’s manual. List Paired Cellular Phone Names • Press the ’Phone’ button to begin. • After the “Ready” prompt and the following beep,[...]

• The selected phone will be used for the next phone call. If the selected phone is not available, the UCon- nect™ system will return to using the highest priority phone present in or near (appr oximately with in 30 feet) the vehicle. Delete UConnect™ Paired Cellular Phones • Press the ’Phone’ button to begin. • After the ⬙ Ready ?[...]

• low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English and Spanish accents, the system may not always work for some. • When navigating through an automated system, such as, voice mail, or when sending a page, at the end o[...]

• dry weather condition. • Operation from driver seat. • Performance, such as, audio clarity , echo. and loud- ness to a large degr ee, rely on the phone and network, and not the UConnect™ system. • Echo at far end can sometime be reduced by lowering the in-vehicle audio volume. Bluetooth Communication Link Cellular phones have been found[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 103 3[...]

104 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 105 3[...]

North American English Primary Alternate(s) Zero Oh Add location Add new All All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return. Main menu Select phone select Set up [...]

40-20-40 Front Seat As the name implies, the seat is divided into 3 segments. The outboard seat portions ar e each 40% of the total width of the seat. The back of the center portion (20%) easily folds down to provide an armr est/center storage compartment (if equipped). Each outboard seat is independently adjustable forwar d orr earward and is equi[...]

Reclining Seats The recliner handle is on the outside of the seat cushion. Pull up on the handle, as shown, to release the seat back and adjust for comfort. W ARNING! Y ou can be seriously , even fatally , injured riding in a seat with the seatback reclined. Do not ride with the seatback reclined so that the shoulder belt is no longer resting again[...]

T o lower the head restraint, push in the button and then push down on the head restraint. Manual Rotary Lumbar Support Adjustment — If Equipped Rotating the lumbar control knob on the left side of the driver’s seatback and on the right side of the passenger’s seatback increases or decr eases the lumbar (lower back) support. Head Restraint Ad[...]

Power Seats — If Equipped CAUTION! Don’t put anything under a power seat. It may cause damage to the seat controls. Power Seat Control Location 1 10 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

The power seat controls ar e on the outboard side of the front seat cushions. Thr ee switches control the seat move- ment. The four-way switch in the center can be moved forward or backwar ds to get the most comfortable posi- tion. The same switch can be moved up and down to control seat height. Change the seat angle by using the two toggle switche[...]

Heated Seats — If Equipped The heated seat switches are located in the instr ument panel under the climate controls. The engine must be running for the heated seats to operate. Each heated seat switch has two settings (HI and LOW). Press the switch once to obtain the desir ed heating position and press a second time in the same dir ection to turn[...]

TO OPEN AND CLOSE THE HOOD T o open the hood, two latches must be released. First pull the hood release lever located below the steering wheel at the base of the instrument panel. Once the hood is released you must r each into the opening beneath the center of the grille and push up the latch to release the safety catch before raising the hood. T o[...]

W ARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are latched fully before driving. LIGHTS Interior Lights Courtesy/ dome lights are turned on when the fr ont doors are opened, when the dimmer contr ol (rotating wheel on the right side of the switch) is rot[...]

turn on the cargo light located on the back of the cab. When a door is open and the interior lights are on, rotating the dimmer contr ol all the way down to the OFF detent will cause all the interior lights to go out. This is also known as the ⬙ Party ⬙ mode because it allows the doors to stay open for extended periods of time without dischargi[...]

Headlamp Delay — If Equipped T o aid in your exit, your vehicle, if equipped, can be programmed by your dealer with a headlamp delay that will leave the headlamps on for 0, 30, 60, or 90 seconds. This delay is initiated when the ignition is turned OFF while the headlamp switch is on, and then the headlamp switch is cycled off. The headlamps will [...]

Plastic is not as scratch resistant as glass and ther efore differ ent lens cleaning procedur es must be followed. T o minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. T o remove r oad dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solve[...]

CARGO LIGHT The cargo lights ar e turned on by rotating the dimmer control to the optional fully upwar d position. The cargo lights will also turn on for 30 seconds when a key fob Unlock is pressed, as part of the illuminated entry feature. MUL TIFUNCTION CONTROL LEVER The multifunction control lever is located on the left side of the steering colu[...]

Passing Light Y ou can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer - ing wheel. This will cause the high beam headlights to turn on until the lever is released. High Beam / Low Beam Select Switch Pull the multifunction control lever fully towar d the steering wheel to switch the headligh[...]

Windshield Wipers The wipers and washers are operated by a switch in the multifunction control lever . T urn the end of the handle to select the desired wiper speed. Intermittent W iper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desira[...]

The delay interval decreases as you r otate the knob until it enters the LO continual speed position. The delay can be regulated fr om a maximum of about 15 seconds between cycles, to a cycle every 2 seconds. The delay intervals will double in duration when the vehicle speed is 10 mph (16 km) or less. W ARNING! Sudden loss of visibility through the[...]

TIL T STEERING COLUMN T o tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Release the lever to lock the column firmly in place. W ARNING! T ilting the steering column while the vehicle is moving is dangerous. W ithout a stable steering col- umn, you could lose control of the vehicle a[...]

DRIVER ADJUST ABLE PEDALS — IF EQUIPPED The power adjustable accelerator and brake pedals allow the driver to establish a comfortable position relative to the steering wheel and pedals. Adjustment 1. Position the driver seat so that you are at least 10 inches (254 mm) away from the airbag located in the center of the steering wheel. 2. Fasten and[...]

CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over accelerator opera- tion at [...]

T o Set At A Desired Speed When the vehicle has reached the desir ed speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. T o Deactivate A soft tap on the brake pedal, normal braking, clutch pressur e while slowing the vehicle, or pressing the CAN- CEL button will deactivate speed cont[...]

T o decrease speed while the speed contr ol is on, press and hold the DECEL button. Release the button when the desired speed is r eached, and the new speed will be set. T o Accelerate For Passing Depress the accelerator as you would normally . When the pedal is released, the vehicle will r eturn to the set speed. NOTE: When driving uphill, at elev[...]

OVERHEAD CONSOLE— IF EQUIPPED The two optional overhead consoles may consist of the following features: • Courtesy/Reading Lights • Compass/T emperature Mini-T rip Computer (CMTC) — If Equipped • Universal Garage Door Opener — If Equipped Courtesy/Reading Lights In the middle of the console are two courtesy/r eading lights. Both lights [...]

OVERHEAD CONSOLE WITH COMP ASS/ TEMPERA TURE MINI-TRIP COMPUTER — IF EQUIPPED This optional overhead console consists of the following: • Courtesy Lights • Compass/T emperature Mini-T rip Computer (CMTC) This overhead console allows you to choose between a compass/temperature display and one of four trip con- ditions being monitored. US/M But[...]

RESET Button Use this button to reset the following displays to zer o: A verage Fuel Economy T rip Odometer Elapsed time Global Reset If the RESET button is pressed twice within 2 seconds while in any of the 3 resettable displays, the Global Reset will reset all 3 displays. Step Button Use this button to choose or cycle through the four trip condit[...]

A verage Fuel Economy (A VG ECO) Shows the average fuel economy since the last reset. This display mode becomes less sensitive to instantaneous changes in fuel consumption as the number of total vehicle miles since the last reset incr eases. It is suggested that this mode be reset periodically for general operation or when driving conditions change[...]

T rip Odometer (ODO) This display shows the distance traveled since the last reset. Elapsed Time (ET) This display shows the accumulated ignition ON time since the last reset. C/T Button Use this button to select a readout of the outside tem- perature and one of eight compass headings that indicate the direction in which the vehicle is facing. UNDE[...]

W ARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy , particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage. Automatic Compass Calibration This compass is self-calibrating which eliminates the need to ma[...]

Compass V ariance is the difference between magnetic north and geographic north. In some areas of the country , the differ ence between magnetic and geographic north is great enough to cause the compass to give false r eadings. If this occurs, the compass variance must be set according to the Compass V ariance Map. UNDERST ANDING THE FEA TURES OF Y[...]

T o set the variance: T urn the ignition ON and set the display to “Compass/T emperature.” Pr ess the RESET button approximately five seconds. The last variance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation. Outside T emperature Because the ambient temp[...]

For additional information on HomeLink 威 , call 1–800– 355–3515, or on the internet at www .homelink.com. W ARNING! A moving garage door can cause injury to people and pets in the path of the door . People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” fea[...]

Programming HomeLink NOTE: When programming a garage door opener , it is advised to park outside the garage. It is also recom- mended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmis- sion of the radio-frequency signal. 1. Press and hold the two outer Hom[...]

W ARNING! Y our motorized door or gate will open and close while you are training the Universal T ransceiver . Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects. 2. Position the end of your hand-held transmitter 1-3 inch[...]

If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with ⴖ Program- ming ⴖ steps 6-8 to complete the programming of a r olling code equipped device (most commonly a garage door opener). 6. At the garage door opener receiver (motor-head unit) in the garage, locate the ⬙ learn ⬙ or ⬙ smart ⬙ [...]

If you live in Canada or you are having dif ficulties programming a gate operator by using the ⬙ Pr ogram- ming ⬙ procedur es (regar dless of where you live), replace ⴖ Programming HomeLink ⴖ step 3 with the following: NOTE: If programming a garage door opener or gate operator , it is advised to unplug the device during the ⬙ cycling ⬙ [...]

Reprogramming a Single HomeLink Button T o program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1. Press and hold the desired HomeLink button. DO NOT release the button. 2. The indicator light will begin to flash after 20 seconds. W ithout releasing the HomeLink button, proceed with ⬙ Programming ⬙ step 2[...]

W ARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is a greater risk of being thrown from a vehicle wi[...]

sunroof will automatically r etract. Remove the obstruc- tion if this occurs. Next, press the switch forwar d and release to Expr ess Close. Pinch Protect Override If a known obstruction (ice, debris, etc.) pr events closing, press the switch forwar d and hold for two seconds after the reversal occurs. This allows the sunr oof to move towards the c[...]

Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. Ignition Off Operation The power sunroof switches r emain active for 10 minutes after the ignition switch has been turned off. Opening either front door will cancel this featur e. Sunroof Fully Closed Press the switch forwar d and release to ensur e that [...]

CAUTION! Electrical Outlet Use W ith Engine Off • Many accessories that can be plugged in draw power from the vehicle’s battery , even when not in use (i.e. cellular phones, etc.). Eventually , if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories t[...]

CUPHOLDERS Front Instrument Panel Cupholders — Automatic T ransmission Only Y our new Ram truck is equipped with dual-opening adjustable cupholders. The cupholder is opened and closed by pushing on the front surface. Each opening in the cupholder is adjustable and will hold cups and mugs of various sizes. UNDERST ANDING THE FEA TURES OF YOUR VEHI[...]

T o secure the cup, place the cup to be held into one of the cup wells and then push the cupholder arm toward the cup until it is held stable. Rear Cupholder — Quad Cab — If Equipped Quad Cab vehicles may be equipped with a rear cup- holder that consists of two cupwells for rear passenger convenience. Cupholders with Automatic 146 UNDERST ANDIN[...]

STORAGE Center Storage Compartment — If Equipped The center portion of the seat folds down to provide an armrest with unique storage compartments under the lid. Push the button on the front of the armr est to raise the cover . Inside there is a power outlet (if equipped), removable coin holder (if equipped), and two dividers to configure the stor[...]

Storage and Seats — If Equipped Located in the center of the front 40/20/40 seat cushion there is a storage compartment. Standard cab models also have storage behind the seat. The Quad Cab models provide additional storage under the rear seat. Lift the seat to access the storage compartment. FOLD FLA T LOAD FLOOR — IF EQUIPPED Fold Flat Load Fl[...]

W ARNING! Do not operate the vehicle with loose items stored on the load floor . While driving or in an accident you may experience, abrupt stopping, rapid acceleration, or sharp turns. Loose objects stored on the load floor may move around with force and strike occupants, resulting in serious or fatal injury . Unfolding the Load Floor 1. Lift the [...]

2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position. 3. Reverse the procedure to stor e the load floor . Positioning the Load Floor for Storage Access Under the Seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap located at either side of the load floor . 3. Lift th[...]

4. Reverse the procedure to put the load floor back in the secured down position befor e you operate the vehicle. PICKUP BOX The pickup box on your new Ram has many features designed for utility and convenience. NOTE: If you are installing a toolbox to the fr ont of the pickup box, you must use Mopar 威 toolbox brackets available from your dealer [...]

Y ou can carry wide building materials (sheets of ply- wood, etc.) by building a raised load floor . Place lumber across the box in the indentations pr ovided above the wheel housings and in the bulkhead dividers to form the floor . W ARNING! The pickup box is intended for load carrying pur- poses only , not for passengers, who should sit in seats [...]

There ar e stampings in the sheet metal on the inner side bulkheads of the box in front of and behind both wheel housings. Place wooden boards acr oss the box from side to side to create separate load compartments in the pickup box. There ar e four tie-down cleats bolted to the lower sides of the pickup box that can sustain loads up to 1000 lbs (45[...]

NOTE: Dual rear wheel pickup models r equire pr operly spaced rear clearance lights. If such a vehicle is operated without a tailgate, suitable lights must be installed. 154 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

W ARNING! T o avoid inhaling carbon monoxide, which is deadly , the exhaust system on vehicles equipped with “Cap or Slide-In Campers” should extend beyond the overhanging camper compartment and be free of leaks. UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 155 3[...]

[...]

UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instruments And Controls ................. 1 6 0 䡵 Instrument Cluster ...................... 1 6 1 䡵 Instrument Cluster Description ............. 1 6 2 䡵 Electronic Digital Clock .................. 1 7 0 ▫ Clock Setting Procedur e................. 1 7 0 䡵 Sales Code RBB—AM/FM Stereo Rad[...]

▫ T uning ............................. 1 7 7 ▫ Radio Data System (RDS) ............... 1 7 8 ▫ PTY (Pr ogram T ype) Button .............. 1 7 8 ▫ Balance ............................ 1 8 0 ▫ Fade .............................. 1 8 0 ▫ T one Control ........................ 1 8 0 ▫ AM/FM Selection ..................... 1 8 0 ▫ Scan [...]

▫ T ime Button ......................... 1 8 6 ▫ Scan Button ......................... 1 8 6 ▫ CD Changer Control Capability — If Equipped ........................... 1 8 6 䡵 Sales Code RBK—AM/ FM Stereo Radio W ith CD Player And CD Changer Controls ........ 1 8 7 ▫ Radio Operation ...................... 1 8 7 ▫ CD Player Operation [...]

INSTRUMENTS AND CONTROLS 160 UNDERST ANDING YOUR INSTRUMENT P ANEL[...]

INSTRUMENT CLUSTER UNDERST ANDING YOUR INSTRUMENT P ANEL 161 4[...]

INSTRUMENT CLUSTER DESCRIPTION 1. Malfunction Indicator Light This light is part of an onboard diagnostic system which monitors the emissions and engine control system. If the vehicle is ready for emissions testing the light will come on when the ignition is first turned on and remain on, as a bulb check, until the engine is started. If the vehicle[...]

the pointer moves to either extreme left or right and remains ther e during normal driving, the electrical sys- tem should be serviced. NOTE: If the gauge pointer moves to either extreme of the gauge, the “Check Gages” indicator will illuminate and a single chime will sound. 3. T urn Signal Indicators Lights in instrument cluster flash when out[...]

unbuckled, a chime will sound. After the bulb check or when driving, if the driver seat belt remains unbuckled, the Seat Belt W arning Light will flash or remain on continuously . Refer to ⬙ Enhanced Driver Seat Belt Re- minder System (BeltAlert™) ⬙ in the Occupant Restraints section for more information. (See page 33 for mor e information.) [...]

light will come on when the ignition key is turned to the ON position and may stay on for five seconds. If the ABS light remains on or comes on during driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is requir ed. See your autho- rized dealer immediately . The ABS light could also illuminate d[...]

14. Security The light will flash rapidly for approximately 16 seconds when the vehicle theft alarm is arming. The light will flash at a slower rate after the alarm is set. The security light will also come on for about two seconds when the ignition is first turned ON. 15. T ransmission Range Indicator (Automatic T ranmissions Only) When the gear s[...]

Acceleration which causes the rear wheels to slip for a period of time may result in the r ed brake light illumi- nating and a brake switch code being set on ABS equipped vehicles. Depressing the brake pedal should extinguish the red brake light. 19. W ait T o Start Indicator The W ait T o Start Indicator will illuminate when the ignition key is fi[...]

21. LAMP OUT Light The LAMP OUT indicator in the instr ument cluster alerts the driver if a defective bulb or wiring circuit is detected for headlamps, turn signal lamps, and stop lamps. 22. TOW/HAUL (Automatic T ransmissions Only) The TOW/HAUL button is located at the end of the gear shift lever . This light will illuminate when the TOW/ HAUL butt[...]

reserve fuel capacity , which corresponds to appr oxi- mately 8% of tank volume. This reserve capacity was put in place to prevent the likelihood of customers r unning out of fuel when operating at maximum load conditions in areas wher e there ar en’t many gas stations. (See page 130 for more information.) Ram fuel tank volumes are as follows: ?[...]

ELECTRONIC DIGIT AL CLOCK The clock and radio each use the display panel built into the radio. A digital readout shows the time in hours and minutes whenever the ignition switch is in the “ON” or “ACC” position. When the ignition switch is in the “OFF” position, or when the radio frequency is being displayed, time keep- ing is accuratel[...]

Radio Operation Power/V olume Control Press the ON/VOL control to turn the radio on. T urn the volume control clockwise to incr ease the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. Electronic V olume Control The electronic volume contr ol turns continuo[...]

and press and r elease that button. If a button is not selected within 5 seconds after pressing the SET button, the station will continue to play but will not be locked into push-button memory . Y ou may add a second station to each push-button by repeating the above pr ocedure with this exception: Pr ess the SET button twice and SET 2 will show in[...]

AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency . The display will show ST when a stereo station is received in the FM mode. Mode Button Press the MODE button to select between the cassette tape player , CD changer , or the Satellite Radio (if equipped). When the Sat[...]

The SEEK symbol appears on the display when Music Search is in operation. Music Sear ch shuts off automati- cally when a selection has been located. Selective Music Search Press the SEEK button up or down to move the track number to skip forward or backwar d 1 to 7 selections. Press the SEEK button once to move 1 selection, twice to move 2 selectio[...]

CD Changer Control Capability — If Equipped This radio is compatible with a remote mounted CD changer available through Mopar Accessories. The fol- lowing instructions ar e for the radio controls that operate this CD changer . Mode Button T o activate the CD changer , press the MODE button until CD information appears on the display . Push-Button[...]

Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. CD Diagnostic Indicators When driving over a very rough r oad, the CD player may skip momentarily . Skipping will not damage the disc or the player , and play will resume automatically . As a safeguard and to pr otect your CD pl[...]

SALES CODE RAZ—AM/ FM STEREO RADIO WITH CASSETTE T APE PLA YER, CD PLA YER AND CD CHANGER CONTROLS Operating Instructions — Radio NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio. Power Switch, V olume Control Press the ON/VOL control to turn the radio on. T urn the[...]

Radio Data System (RDS) The Radio Data System allows radio broadcasting sta- tions to send data signals on a subcarrier frequency which is added to the stereo signal. RDS was developed to give FM receivers user -friendly features, such as Program Service name (PS) and Pr ogram T ype (PTY). Program Service name is typically used by the br oad- caste[...]

Program T ype Radio Display Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc Religious T alk Rel T alk Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B Sports Sports T alk T alk T op 40 T op 40 W eather W eather By pressing the SEEK button when the PTY icon is displayed, the radio will [...]

Balance The Balance control adjusts the left-to-right speaker bal- ance. Push in the button and it will pop out. Adjust the balance and push the button back in. The balance will be displayed and continuously updated while the button is turned. Fade The Fade control pr ovides for balance between the front and rear speakers. Push in the button and it[...]

T o Set The Radio Push-button Memory When you are r eceiving a station that you wish to commit to push-button memory , press the SET button. SET 1 will show in the display window . Select the push-button you wish to lock onto this station and press and release that button. If a station is not selected within 5 seconds after pressing the SET button,[...]

Press the SEEK button up or down to move the track number to skip forward or backwar d 1 to 6 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc. Fast Forward (FF) Press the FF button up momentarily to advance the tape in the direction that it is playing. The tape will advance until the button is pressed aga[...]

Pinch Roller Release If ignition power or the radio ON/OFF switch are turned off, the pinch r oller will automatically retract to pr otect the tape from any damage. When power is r estored to the tape player , the pinch roller will automatically r eengage and the tape will resume play . Noise Reduction The Dolby Noise Reduction System* is on whenev[...]

If the volume control is ON, the unit will switch fr om radio to CD mode and begin to play . The display will show the track number and index time in minutes and seconds. Play will begin at the start of track one. NOTE: • Y ou may eject a disc with the radio OFF . The ignition switch must be in the ON or ACC position to insert a disc with the rad[...]

FF/TUNE/RW Press FF (Fast Forwar d) and the CD player will begin to fast forward until FF is r eleased. The R W ( Reverse) button works in a similar manner . Program Button 4 (Random Play) Press this button while the CD is playing to activate Random Play . This feature plays the tracks on the se- lected disc in random order to pr ovide an interesti[...]

Time Button Press this button to change the display fr om elapsed CD playing time to time of day . Scan Button Press this button to play the first 10 seconds of each track. T o stop the scan function, press the button a second time. CD Changer Control Capability — If Equipped This radio is compatible with a remote mounted CD changer available thr[...]

CD Diagnostic Indicators When driving over a very rough r oad, the CD player may skip momentarily . Skipping will not damage the disc or the player , and play will resume automatically . As a safeguard and to pr otect your CD player , one of the following warning symbols may appear on your display . A CD HOT symbol indicates the player is too hot. [...]

NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. Seek Press and r elease the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up or the bottom to seek down. The radio will remain tuned to the new station unt[...]

Audio The audio button controls the BASS, TREBLE, BAL- ANCE, and F ADE. Press the AUDIO button and BASS will be displayed. Press the SEEK + or SEEK – to incr ease or decrease the Bass tones. Press the AUDIO button a second time and TREB will be displayed. Press the SEEK + or SEEK – to incr ease or decrease the T r eble tones. Press the AUDIO bu[...]

NOTE: Changes or modifications not expressively ap- proved by the party r esponsible for compliance could void the user’s authority to operate the equipment. CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the volume control ON befor e the CD player will operate. Inserting The Compact Disc CAUTION! This CD play[...]

If you do not remove the disc within 15 seconds, it will be reloaded. The unit will continue in radio mode. The disc can be ejected with the radio and ignition OFF (except on convertibles). FF/TUNE/R W Press FF (Fast Forwar d) and the CD player will begin to fast forward until FF is r eleased. The R W ( Reverse) button works in a similar manner . R[...]

Mode Button T o activate the CD changer , press the MODE button until CD information appears on the display . Disc Up/Program Button 1 Press the DISC up (button 1) button to play the next available disc. Disc Down/Program Button 5 Press the DISC down (button 5) button to play the previous disc. Seek Button Press the SEEK up or down to select anothe[...]

CD HOT will pause the operation. Play can be resumed when the operating temperature is corr ected or another MODE is selected. An ERR symbol will appear on the display if the laser is unable to read the Disc data for the following r easons: • Excessive vibration • Disc inserted upside down • Damaged disc • W ater condensation on optics SALE[...]

NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio. Mode Press the MODE button r epeatedly to select between AM, FM, the CD changer and Sirius Satellite Radio™ (if equipped). The display will show ST when a stereo station is received. T o select Sirius Satellite Radio?[...]

and release that button. If a button is not selected within 5 seconds after pressing the SET RND button, the station will continue to play but will not be locked into push- button memory . Y ou may add a second station to each push-button by repeating the above pr ocedure with this exception: Pr ess the SET button twice and SET 2 will show in the d[...]

General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesir ed opera- tion. NOTE: Changes or modifications[...]

show the disc number , the track number , and index time in minutes and seconds. Play will begin at the start of track 1. LOAD/ EJT — Load Press the LOAD/ EJT button and the button with the corresponding number wher e the CD is being loaded. After the radio displays “load” insert the CD into the player . Radio display will show “loading” [...]

FF/TUNE/R W Press FF (Fast Forwar d) and the CD player will begin to fast forward until FF is r eleased. The R W ( Reverse) button works in a similar manner . Random Play — SET / RND Press the RND button while the CD is playing to activate Random Play . This feature plays the tracks on the disc in random order to pr ovide an interesting change of[...]

Program T ype Radio Display Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc Religious T alk Rel T alk Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B Sports Sports T alk T alk T op 40 T op 40 W eather W eather By pressing the SEEK button when the PTY i[...]

T ime Press the TIME button to change the display fr om elapsed CD playing time to time of day . Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. CD Diagnostic Indicators When driving over a very rough r oad, the CD player may skip momentarily . Skipping will not damage the di[...]

REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system contr ols are located on the r ear surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a r ocker type switch with a button in the center . Pressing the top of the switch will increase the volume and pr essing the bottom of the sw[...]

T ape Player Pressing the top of the switch once will go to the next selection on the cassette. Pressing the bottom of the switch once will go to the beginning of the current selection or to the beginning of the previous selection if it is within the first 5 seconds of the current selection. If you press the switch up or down twice it plays the sec[...]

5. A loose tape should be corrected befor e use. T o rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the requir ed directions. Maintain your cassette tape player . The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played. The result of [...]

NOTE: If you experience difficulty in playing a particu- lar disc, it may be damaged, oversized, or have theft protection encoding. T ry a known good disc befor e considering disc player service. RADIO OPERA TION AND CELLULAR PHONES Under certain conditions, the operation of a cellular phone in your vehicle can cause erratic or noisy perfor- mance [...]

Heater Only — Fleet V ehicles The mode control (at the right of the control panel) can be set in any of the following positions: NOTE: T o improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are iden- tified by the small dots. Panel Outside air flows thro[...]

Bi-Level Outside air flows through the outlets located in the instrument panel and at the floor . Mix Outside air flows in equal proportions thr ough the floor and defroster outlets. Defrost Outside air is primarily directed to the windshield through the defr oster outlets located at the base of the windshield, and the demister outlets located at t[...]

T emperature Control The rotary knob at the center of the control panel contr ols the temperature of the inte- rior air . Y ou can choose your degree of comfort by r otating the knob. The coldest tem- perature setting is to the ex- treme left (blue r egion) and the warmest setting is to the extreme right (r ed region) of the rotation. Air Condition[...]

snowflake button shows that the air conditioning is on. Press the button a second time to turn the air condition- ing off. Slight changes in engine speed or power may be noticed when the air conditioning compressor is on. This is a normal occurrence as the compr essor will cycle on and off to maintain comfort and incr ease fuel economy . The mode c[...]

Floor Outside air flows primarily through the floor out- lets located under the instrument panel. Mix Outside air flows in equal proportions thr ough the floor and defroster outlets, and the air conditioning may be on. Defrost Outside air is primarily directed to the windshield through the defr oster outlets located at the base of the windshield, a[...]

T emperature Control The rotary knob at the center of the control panel contr ols the temperature of the inte- rior air . Y ou can choose your degree of comfort by r otating the knob. The coldest tem- perature setting is to the ex- treme left (blue r egion) and the warmest setting is to the extreme right (r ed region) of the rotation. Circulation T[...]

turn off after activation, when 15 minutes have elapsed. T o reactivate, simply pr ess the button again. Air Conditioning with Dual Zone T emperature Control — If Equipped W ith the Dual Zone T emperature Contr ol System, each front seat occupant can independently contr ol the tem- perature of air coming fr om the outlets on their side of the veh[...]

A/C Pushbutton W ith the fan control in the ON posi- tion, pushing the A/C button turns on the air conditioning compressor . An indicator light on the button shows that the Air Conditioning compressor is on. Conditioned air is now directed through the mode outlets selected. Pushing the button a second time turns the compressor OFF . Recirculation P[...]

Bi-Level Air flows through the outlets located in the instr u- ment panel and those located on the floor . NOTE: There is a dif ference in temperatur e between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives impr oved comfort during sunny but cool conditions. Heat Outside air flows primari[...]

Dual Zone T emperature Control Use this control to r egulate the temperature of the air inside the passenger compartment. This is accomplished by having separate temperature contr ol slides for both the driver and front passenger . The blue area of the scale indicates cooler temperatures while the r ed area indicates warmer temperatures. Electric R[...]

edges of the instrument panel. The demisters also pr o- vide extra air ducts for circulation. They ar e in operation whenever the Floor , Mix or Defrost modes ar e in use. NOTE: When you turn off the engine you may hear a hissing sound from under the hood for a short period of time. This is a normal condition that occurs if the air conditioning sys[...]

speeds will reduce fogging. Interior fogging on the windshield can be quickly removed by selecting the defrost mode. Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigar ette smoke, perfumes, etc.) from sticking to the windows. Contaminates incre[...]

Operating Tips Chart UNDERST ANDING YOUR INSTRUMENT P ANEL 217 4[...]

[...]

ST ARTING AND OPERA TING CONTENTS 䡵 Ignition/Starter Switch ................... 2 2 3 ▫ Lock .............................. 2 2 3 ▫ O f f ............................... 2 2 3 ▫ O n................................ 2 2 3 ▫ Start .............................. 2 2 3 ▫ A C C .............................. 2 2 4 ▫ Manual T ransmission Key[...]

▫ Operating Precautions .................. 2 3 5 ▫ Cooling System T ips — Automatic T ransmission ........................ 2 3 6 䡵 T ransmission Shifting .................... 2 3 7 ▫ Automatic T ransmission W ith Overdrive— If Equipped ........................... 2 3 7 ▫ Manual T ransmission — 6-Speed — If Equipped ...............[...]

▫ T ire Inflation Pressur es ................. 2 6 9 ▫ Radial-Ply T ires ...................... 2 7 1 ▫ Compact Spare T ire — If Equipped ......... 2 7 2 ▫ Limited Use Spare — If Equipped ......... 2 7 3 ▫ T ire Spinning ........................ 2 7 3 ▫ T read W ear Indicators .................. 2 7 4 ▫ Replacement T ires ........[...]

▫ T railer T owing Information (Maximum T railer W eight Ratings) ...................... 2 9 5 ▫ T railer T owing Mirrors — If Equipped ...... 2 9 6 ▫ Cooling System T ips — T railer T owing ...... 2 9 7 ▫ Automatic T ransmission Oil T emperature W arning Light ....................... 2 9 8 ▫ T owing W ith An Automatic T ransmission .[...]

IGNITION/ST ARTER SWITCH LOCK Locks the automatic transmission shift control into the P ARK position. It also engages the steering wheel lock (if equipped) when the steering wheel is turned. NOTE: This vehicle is equipped with a transmission shift interlocking system. The brake pedal must be depressed to shift out of Park (P). OFF Unlocks the steer[...]

ACC Allows the electrical accessories to be used when the engine is not running. Manual T ransmission Key Release Button T o remove the key on vehicles equipped with manual transmissions, turn the key to the Lock position and press the button to remove the ignition key . Key Reminder An alarm will sound to remind you if the key is left in the ignit[...]

• A heated intake air system both improves engine starting and reduces the amount of white smoke generated by a warming engine. Normal Starting Procedure — Engine Manifold AirT emperature Above 66°F (19°C) Observe the Instrument Panel Cluster lights when start- ing the engine. 1. Always apply the parking brake. 2. Shift into P ARK for an auto[...]

CAUTION! Do not crank engine for more than 15 seconds at a time as starter motor damage may result. T urn key to OFF and wait at least two minutes before trying again. 5. When the engine starts, release the key . 6. Check to see that there is oil pressur e. 7. Release the parking brake. Starting Procedure — Engine Manifold Air T emperature Below [...]

• After the W AIT TO ST ART light goes of f, turn the ignition key to ST AR T . Do not press the accelerator during starting. • Check to see that there is oil pr essure. • Allow the engine to idle at fast idle for about three minutes until the manifold heaters have completed the post-heat cycle. • Release the parking brake and drive. NOTE: [...]

NOTE: Excessive white smoke and poor engine perfor- mance will result if manifold heaters ar e not recycled. • Heat generated by the manifold heaters dissipates rapidly in a cold engine. If more than two minutes pass between the time the W AIT TO ST ART light goes OFF and the engine is started, recycle the manifold heaters by turning the ignition[...]

4. Repeat the procedure if the engine does not start. W ARNING! Do not open the high pressure fuel system with the engine running. Engine operation causes high fuel pressure. High pressure fuel spray can cause serious injury or death. NOTE: The engine may run r ough until the air is forced from all the fuel lines. Starting Fluids W ARNING! ST AR TI[...]

W ARNING! Do not leave children or animals inside parked vehicles in hot weather . Interior heat build up may cause serious injury or death. NORMAL OPERA TION Observe the following when the engine is operating. • All message center lights are of f. • Check Engine Lamp is off. • Engine Oil Pressur e is above 10 psi (69 kPa) at idle. • Low Oi[...]

Cold Weather Precautions Operation in ambient temperature below 32°F (0°C) may requir e special considerations. The following charts sug- gest these options: Fuel Operating Range *No. 1 diesel fuel should only be used where extended arctic conditions (-10°F/-23°C) exist. NOTE: • Use of Climatized Diesel Fuel or Number 1 Diesel Fuel results in[...]

The block heater must be plugged in at least one hour to have an adequate warming effect on the coolant. W ARNING! Remember to disconnect the cord before driving. Damage to the 1 10–1 15 volt electrical cord could cause electrocution. NOTE: The block heater will requir e 1 10 V olts AC and 6.5 Amps to activate the heater element. Block Heater Usa[...]

Arctic Operation Where ther e are no pr ovisions to keep the engine warm when it is operating in ambient temperatures consistently below (-10°F/-23°C), use 5W -40 synthetic engine oil and fuel that meets the requir ements in Section 7, “Mainte- nance Procedur es,” Engine Oil Selection. Engine W arm-Up A void full throttle operation when the e[...]

NOTE: • If ambient temperatures ar e low and the coolant temperature is below 200°F (93°C), the engine idle speed will slowly increase to 1000 RPM after 2 minutes of idle, if the following conditions are met: • foot is off brake pedal and thr ottle pedal • automatic transmission is in Park (P) • vehicle speed is zero • Applying the thro[...]

Driving Condition Load T urbocharger T emperature Idle T ime (min.) Before Engine Shutdown Stop and Go Empty Cool Less than One Stop and Go Medium One Highway Speeds Medium W arm T wo City T raffic Maximum GCWR Three Highway Speeds Maximum GCWR Four Uphill Grade Maximum GCWR Hot Five Engine Speed Control CAUTION! Prevent overspeeding the engine goi[...]

A void Low Coolant T emperature Operation Continual operation at low coolant temperature below the normal range on the gauge (140°F/60°C) can be harmful to the engine. Low coolant temperature can cause incomplete combustion which allows carbon and varnish to form on piston rings and injector nozzles. Also, the unburned fuel can enter the crankcas[...]

Do Not Operate The Engine W ith Failed Parts Practically all failures give some warning befor e the parts fail. Be on the alert for changes in performance, sounds, and visual evidence that the engine requir es service. Some important clues are: • engine misfiring or vibrating severely • sudden loss of power • unusual engine noises • fuel, o[...]

“P” Park This gear position supplements the parking brake by locking the transmission. The engine can be started in this range. Never use Park while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply parking brake first, then place the selector in Park position. On 4-wheel drive vehicles be su[...]

“N” Neutral Shift to Neutral when the vehicle is standing for pro- longed periods with the engine running. The engine may be started in this range. Set the parking brake if you must leave the vehicle. “D” Drive This position provides all forwar d gears, including 3rd gear direct and 4th or 5th (if equipped) gear over drive (see Overdrive Op[...]

When T o Use “TOW/HAUL” Mode When driving in hilly areas, towing a trailer , carrying a heavy load, etc., and frequent transmission shifting oc- curs, press the “T OW/HAUL” button. This will improve performance and reduce the potential for transmission overheating or failur e due to excessive shifting. When operating in “TOW/HAUL” mode,[...]

T orque Converter Clutch A feature, designed to improve fuel economy , has been included in the automatic transmission on your vehicle. A clutch within the torque converter engages automati- cally at calibrated speeds. This may result in a slightly differ ent feeling or response during normal operation in high gear . When the vehicle speed drops or[...]

Fully depress the clutch pedal befor e shifting gears. As you release the clutch pedal, lightly depr ess the accelera- tor pedal. When launching a stationary vehicle, keep the engine speed low until the clutch is fully engaged. This transmission has a “creeper” 1st gear which should be used to start from a standing position when carrying a payl[...]

avoid overspeeding the engine and clutch. For accelera- tion at speeds less than 15 mph (25 km/h), 2nd gear is recommended. CAUTION! When descending a hill, be very careful to downshift one gear at a time to prevent overspeeding the engine which can cause valve damage. FOUR-WHEEL- DRIVE OPERA TION — IF EQUIPPED • Four-Wheel-Drive Dodge Ram T ru[...]

The 4-wheel-drive light (4WD), located in the instrument cluster , alerts the driver that the vehicle is in 4-wheel drive and that the front and r ear driveshafts are locked together . This light illuminates when the transfer case is shifted to either the 4H or 4L positions. There is no light for the 2H or N (Neutral) positions. When operating your[...]

W ARNING! Y ou or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission p[...]

Shifting Procedure - Manually Shifted T ransfer Case 2H ⇔ 4H Shifting between 2H and 4H can be made with the vehicle stopped or in motion. If the vehicle is in motion, shifts can be made up to 55 mph (88 km/h). W ith the vehicle in motion, the transfer case will engage / disen- gage faster if you momentarily release the accelerator pedal after co[...]

NOTE: Shifting into or out of 4L is possible with the vehicle completely stopped, however difficulty may oc- cur due to the mating clutch teeth not being properly aligned. Several attempts may be requir ed for clutch teeth alignment and shift completion to occur . The pre- ferred method is with the vehicle r olling 2 to 3 mph (3 to 5 km/h). A void [...]

position - see Shifting Procedur e section for specific shifting instructions. The 4HI and 4LO positions ar e designed for loose, slippery road surfaces only . Driving in the 4HI and 4LO positions on dry hard surfaced r oads may cause increased tir e wear and damage to the driv- eline components. NOTE: The transfer case Neutral (N) position is sele[...]

NOTE: Before r etrying a selection, make certain that all the necessary requir ements for selecting a new transfer case position have been met. T o retry the selection, turn the control knob back to the curr ent position, wait five (5) seconds, and retry selection. T o find the shift require- ments, refer to the ⬙ Shifting Pr ocedure ⬙ for your[...]

When operating your vehicle in 4LO, the engine speed is approximately thr ee times that of the 2WD/A WD or 4HI positions at a given road speed. T ake care not to over- speed the engine and do not exceed 25 mph (40 km/h). Proper operation of 4 wheel drive vehicles depends on tires of equal size, type and cir cumference on each wheel. Any differ ence[...]

For additional information on the appropriate use of each transfer case mode position see the information below: 2WD/A WD Rear Wheel Drive High Range - Normal street and highway driving. Dry hard surfaced r oads. 4HI 4 Wheel Drive High Range - Locks the front and r ear driveshafts together . Forces the fr ont and rear wheels to rotate at the same s[...]

NOTE: If any of the requir ements to select a new transfer case position have not been met, the transfer case will not shift.The indicator light for the previous position will remain ON and the newly selected position indicator light will continue to flash until all the requir ements for the selected position have been met. T o retry a shift: retur[...]

key must be in the ON position with the engine either RUNNING or OFF . This shift cannot be completed if the key is in the accessory position. NOTE: The 4x4 system will not allow shifts between (2WD/A WD)/4HI if the front and/or r ear wheels are spinning (no traction). In this situation the selected position indicator light will flash and the origi[...]

3. Rotate the transfer case control switch to the desired position. 4. After the desired position indicator light is ON (not flashing), shift transmission back into gear (release clutch on manual transmissions). NOTE: If steps 1 or 2 of either the Preferr ed or Alternate Procedur e are not satisfied prior to attempting the shift or if they no longe[...]

W ARNING! On vehicles equipped with a limited-slip differen- tial, never run the engine with one rear wheel off the ground, since the vehicle may drive through the rear wheel remaining on the ground. Y ou could lose control of the vehicle. Care should be taken to avoid sudden accelerations when both rear wheels ar e on a slippery surface. This coul[...]

load on the transmission locking mechanism may make it difficult to move the selector out of P ARK. W ARNING! • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury . Also be certain to leave an automatic trans- mission in Park, a manual transmission in Reverse or first gear . Failure to do so [...]

Brake Noise During normal operation of the brake system certain noises may be present fr om time to time. Occasional ⬙ groan ⬙ or ⬙ squeal ⬙ noises may occur during normal operation of the brake system which may not be indica- tive of a problem. These noises may be hear d at any time the brakes are applied but may be mor e noticeable during[...]

W ARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in tur[...]

ABS W arning Light The Anti-lock Brake System includes an amber warning light, located in the instrument cluster . When the light is illuminated, the Anti-lock Brake System is not function- ing. The system reverts to standar d non-anti-lock brakes. W ARNING! Pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accide[...]

TIRE SAFETY INFORMA TION Tire Markings NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tir es have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tir e sizing is based on European design standards. T ires designed to this standar d have[...]

T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standar ds ⴖ ....blank.... ⴖ = Passenger car tire based on Eur opean design standards LT = Light T ruck tire based on U.S. design standar ds T = T emporary Spare tir e 31 = Overall Diameter in Inches (in) 215 = Section W idth in Milimeters (mm) 65 = A[...]

EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corr esponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be [...]

Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the T[...]

Tire Loading and T ire Pressure T ire Placard Location NOTE: The proper cold tir e inflation pressur e for pas- senger cars is listed on either the face of the driver’s door or the driver’s side “B” pillar . For vehicles other than passenger cars, the cold tire inflation pr essures are listed on either the shutface of the driver’s door , [...]

T ire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle 4) the cold tire inflation pr essures for the fr ont, rear and spare tir es. Loading The vehicle maximum load on th[...]

combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight refer enced here. Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occu- pants and cargo should never exceed XXX pounds” on your vehicle’s placard. 2. Determine the combined weight of the[...]

ST ARTING AND OPERA TING 267 5[...]

W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMA TION Tire Pressure Proper tir e inflation pressur e is essential to the safe and satisfactory op[...]

2. Economy— Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread. These abnormal wear patterns will reduce tr ead life resulting in a need for earlier tire r eplacement. Underinflation also increases tir e rolling r esistance and results in higher fuel consumption. 3. Ride Comfort and V ehicle Stability?[...]

check tire pr essure. Do not make a visual judgement when determining proper inflation. Radial tir es may look properly inflated even when they ar e under inflated. CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which cou[...]

T ire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tir e inflation pressur e is very important. Increased tir e pressur e and reduced vehicle loading may be requir ed for [...]

Compact Spare Tire — If Equipped The compact spare is for temporary emer gency use with radial tires. It is engineer ed to be used on your style vehicle only . Since this tire has limited tread life, the original tire should be r epaired (or r eplaced) and rein- stalled at the first opportunity . W ARNING! T emporary use spare tires are for emerg[...]

Limited Use Spare — If Equipped The limited use spare tir e is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tir e warning label located on the limited use spare tire and wheel assembly . This tire may look like the original equipped tire on the fr ont or rear axle of your vehicle, but it is not. Inst[...]

W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed. T read Wear Indicators [...]

Replacement Tires The tires on your new vehicle pr ovide a balance of many characteristics. They should be inspected regularly for wear and correct cold tir e inflation pressur e. The manu- facturer str ongly recommends that you use tir es equiva- lent to the originals in size, quality and performance when replacement is needed (see the paragraph o[...]

CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. Alignment And Balance Poor suspension alignment may result in: • Fast tire wear . • Uneven tire wear , such as feathering and one-sided wear . • V ehicle pull to right or left. T ires may also cause the vehicle to pull to [...]

CAUTION! T o avoid damage to your vehicle, tires or chains, observe the following precautions: • Because of limited chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious vehicle damage. Stop the vehicle immediately if noise occurs that could sugg[...]

CAUTION! Do not use tire chains on 4x4 Ram trucks equipped with P265/70R17, L T275/70R17 tires. There may not be adequate clearance for the chains and you are risking structural or body damage to your vehicle. Do not use tire chains on the 4X2 front wheels of 2500/3500 SR W (Single Rear Wheels) equipped with L T245/70R17, L T265/70R17 tires or 4X4 [...]

TIRE ROT A TION RECOMMENDA TIONS T ires on the front and r ear axles of vehicles operate at differ ent loads and perform differ ent steering, driving, and braking functions. For these reasons, they wear at unequal rates, and develop irregular wear patterns. These effects can be r educed by timely rotation of tir es. The benefits of rotation ar e es[...]

Dual Rear Wheels The tires used on dual wheel assemblies should be matched for wear to prevent overloading one tir e in a set. T o check if tires ar e even, lay a straight edge across all four tires. The straight edge should touch all the tir es. CAUTION! 3500 Dual Rear T ires have only one approved direc- tion of rotation. This is to accommodate t[...]

ENGINE RUNA W A Y W ARNING! In case of engine runaway due to flammable fumes from gasoline spills or turbocharger oil leaks being sucked into the engine do the following to help avoid personal injury and/or vehicle damage: 1. Shut off engine ignition switch. 2. Using a CO 2 or dry chemical type fire extin- guisher , direct the spray from the fire e[...]

Diesel fuel is seldom completely free of water . T o prevent fuel system trouble, drain the accumulated water fr om the fuel/water separator using the fuel/water separator drain provided. If you buy good quality fuel and follow the cold weather advice above, fuel conditioners should not be requir ed in your vehicle. If available in your area, a hig[...]

Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door . If the gas cap is lost or damaged, be sure the r eplacement cap is for use with this vehicle. CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the[...]

A void Using Contaminated Fuel Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system. Pr oper main- tenance of the engine fuel filter and fuel tank is essential. (See Section 7 for Maintenance Procedur es). NOTE: Climatized diesel fuel is a blend of Number 2 and Number 1 Diesel fuel which reduces the temperatu[...]

Number 2 Diesel Fuel Specifications Fuel Properties - No. 2 - Diesel Reference V iscosity - 1.9 to 4.1 centistokes (ASTM D-445) Cetane Number - 40 min. (ASTM D613) Sulfur Content -.05% by weight (ASTM D-2622) W ater & Sediment - less than 0.05 % by volume (ASTM D-2709) Carbon Residue - Less than.35% (Ramsbottom ASTM D-524 Flash Point - 125°F m[...]

VEHICLE LOADING Certification Label As requir ed by National Highway T raffic Safety Admin- istration Regulations, your vehicle has a certification label affixed to the driver’s side door or pillar . This label contains the month and year of manufacture, Gross V ehicle W eight Rating (GVWR), Gross Axle W eight Rating (GA WR) front and r ear , and[...]

T ire Size This is the minimum allowable tire size for your vehicle. Replacement tires must be equal to the load capacity of this tire size. Rim Size This is the rim size that is appropriate for the tir e size listed. Inflation Pressure This is the cold tire inflation pr essure for your vehicle for all loading conditions up to full GA WR. Curb W ei[...]

CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GA WR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also overloading can shorten the life of your vehicle. An EXAMPLE of a loaded vehicle is shown in the following chart. Note [...]

TRAILER TOWING All Dodge Ram Pickup trucks ar e intended to tow trailers up to 2,000 lbs (907 kg) without added equipment or alterations to standard equipment. Y our vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional T railer T ow Prep Package. See your Dodge dealer for package content. De[...]

CAUTION! • During the first 500 miles (805 km) your new vehicle is driven, do not tow a trailer . Doing so may damage your vehicle. • When first towing a trailer , limit your speed to 50 mph (80 km/h) during the first 500 miles (805 km) of towing. Perform the maintenance listed in the “Maintenance Schedules” section of this manual (Section [...]

must be considered as part of the total load on your vehicle. Refer to the Certification label located at the driver’s door for the Gross V ehicle W eight Rating. W ARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Axle Lubricant and T railer T owing 2500/3500 Models ?[...]

under the bumper . This connector contains the follow- ing vehicle circuits: park/tail lamps, left stop/turn lamp, right stop/turn lamp, and ground. W ith the optional T railer T ow Prep package a 7-way connector is provided with the following additional cir cuits: backup lamp, trailer battery and electric brake. NOTE: Connect trailer lighting and [...]

A frame mounted hitch of up to Class IV rating, as rated by the hitch manufacturer , is supplied as part of the trailer tow prep package. W ith a Class IV Hitch, you can tow a trailer with a Gross T railer W eight of up to 12,000 lbs (5 443 kg) maximum depending on your vehicle equipment. T ongue weight must be equal to at least 10% of the gross tr[...]

CAUTION! Connect trailer lighting and brakes using factory harnesses only . Do not cut or splice wiring to the brake circuits. Use an approved wiring harness con- nector on the trailer . T railer Weight and T railer T ongue Weight Gross T railer W eight (GTW) means the weight of the trailer plus the weight of all cargo, consumables and equipment lo[...]

T ongue weight must be equal to at least 10% of GTW , but no more than 15% of GTW . Also, there ar e maximum tongue weight ratings that are not to be exceeded, as follows: • Class III (the bumper ball type) 500 lbs (227 kg) • Class IV (the receiver hitch type) 1200 lbs (544 kg) NOTE: When towing a trailer , the following require- ments must be [...]

T railer T owing Mirrors — If Equipped These mirrors ar e designed with an adjustable mirror head to provide a gr eater vision range when towing extra-wide loads. T o change position inboard or out- board, the mirr or head should be rotated (flipped Out or In). A small blindspot mirror is integrated onto the main mirror surface. NOTE: • These m[...]

Cooling System T ips — T railer T owing T o reduce potential for engine and transmission over - heating, take the following actions in high ambient temperatures: • City Driving— when stopped, put the transmission in N (Neutral) and increase the engine idle speed. • Highway Driving— reduce your speed. • Air Conditioning— turn it off te[...]

Automatic T ransmission Oil T emperature Warning Light All vehicles with heavy duty transmission oil cooling are equipped with a transmission sump oil temperature sensor and warning light. If elevated transmission tem- peratures ar e encountered, the engine contr oller will select the most desirable gear until the transmission temperatures ar e red[...]

2005 BODY BUILDER’S GUIDE. See your dealer , installer or snowplow manufacture for this information. Ther e are unique electrical systems that must be connected to properly assur e operator safety and prevent overloading vehicle systems. W ARNING! Attaching a snowplow to this vehicle could ad- versely affect performance of the airbag system in an[...]

2. The total GVWR or the Front GA WR or the Rear GA WR should never be exceeded. 3. The snowplow prep packages are not available with the Sport Package. 4. Car go capacity will be reduced by the addition of options or passengers, etc. The loaded vehicle weight, including the snowplow system, all aftermarket accessories, driver , passengers, options[...]

Methods For Removing Snow Operating Tips Under ideal snow plowing conditions, 20 mph (32 km/h) should be maximum operating speed. The operator should be familiar with the area and surface to be cleaned. Reduce speed and use extreme caution when plowing unfamiliar areas or under poor visibility . NOTE: During snowplow usage on vehicles equipped with[...]

• Operate with transfer case in 4L when plowing small or congested areas wher e speeds are not likely to exceed 15 mph (24 km/h). At higher speeds operate in 4H. • V ehicles with 48RE transmissions should use 4L range when plowing deep or heavy snow for extended periods of time to avoid transmission overheating. • Do not shift the transmissio[...]

CAUTION! Internal damage to the transfer case will occur if a front or rear wheel lift is used when recreational towing. NOTE: Both the Manual Shift and Electronic Shift transfer cases must be shifted into Neutral (N) for recr eational towing. Automatic transmissions must be placed in P (Park) position for r ecreational towing. Manual transmissions[...]

5. Shift transfer case lever into N (NEUTRAL). 6. Start the engine. 7. Shift automatic transmission into Reverse (R). 8. Release brake pedal for five seconds and ensure that there is no vehicle movement. 9. Repeat steps 7 and 8 with the transmission in Drive (D). 10. Shut OFF the engine and place the ignition key to the unlocked OFF position. 1 1. [...]

Returning to Normal Operation — Manual Shift T ransfer Case Use the following procedur e to prepar e your vehicle for normal usage: 1. Bring the vehicle to a complete stop. 2. Shut OFF the engine. 3. Depress the brake pedal. 4. Shift automatic transmission to N (NEUTRAL), or depress the clutch on manual transmissions. 5. Shift transfer case lever[...]

CAUTION! • Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and damage the internal parts. Recreational T owing Procedure — Electronic Shift T ransfer Case — If Equipped Use the following procedur e to pre[...]

7. After shift is completed and the Neutral (N) light comes on release Neutral (N) button. 8. Start engine. 9. Shift automatic transmission into Reverse (R). 10. Release brake pedal for five seconds and ensure that there is no vehicle movement. 1 1. Repeat steps 9 and 10 with the transmission in Drive (D). 12. Shut engine OFF and place ignition key[...]

CAUTION! Damage to the transmission may occur if the trans- mission is shifted into Park (P) with the transfer case in Neutral (N) and the engine RUNNING. W ith the transfer case in Neutral (N) ensure that the engine is OFF prior to shifting the transmission into Park (P). Returning to Normal Operation — Electronic Shift T ransfer Case Use the fo[...]

during the 1 second time, then all of the mode position indicator lights will flash continuously until all requir e- ments are met or until the Neutral (N) button is r eleased. NOTE: The ignition key must be ON for a shift to take place and for the position indicator lights to be operable. If the key is not ON, the shift will not take place and no [...]

CAUTION! • Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and fluid loss will damage internal parts. DRIVING OFF-ROAD Care should be taken when attempting to climb steep hills or driving diagonally across a [...]

If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for im- pacted material. Impacted foreign material can cause a wheel imbalance. Removing the foreign material fr om the wheels will correct the situation. TRACTION When driving on wet or slushy roads, it is possible for a wedge of water to build [...]

[...]

WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Lights .................. 3 1 4 䡵 Adding Fuel — 24–V alve Cummins T urbo Diesel ............................... 3 1 5 䡵 Jack Location .......................... 3 1 6 ▫ All Models .......................... 3 1 6 䡵 Changing A Flat T ire .................... 3 1 7 ▫ Removing The [...]

HAZARD W ARNING LIGHTS The Hazard W arning switch is mounted on the top of the steering column as shown in the illustration. T o engage the Hazard W arning lights, depress the button on the top of the steering column. When the Hazard W arning switch is activated, all directional turn signals will flash off and on to warn oncoming traf fic of an eme[...]

ADDING FUEL — 24–V AL VE CUMMINS TURBO DIESEL W ARNING! A fire may result if fuel is pumped into a portable container that is on a truck bed. Y ou could be burned. Always place fuel containers on the ground while filling. NOTE: When a diesel engine is allowed to run out of fuel, air is pulled into the fuel system. Y ou may try priming as descri[...]

4. Repeat the procedure if the engine does not start. CAUTION! Do not engage the starter motor for more than 15 seconds at a time. Allow two minutes between the cranking intervals. NOTE: The engine may run r ough until the air is forced from all the fuel lines. JACK LOCA TION All Models The jack and jack tools are stor ed under the passenger seat. [...]

W ARNING! The jack is designed to use as a tool for changing tires only . The jack should not be used to lift the vehicle for service purposes, unless suitable sup- ports are placed under the vehicle as a safety mea- sure. The vehicle should be jacked on a firm level surface only . A void ice or slippery areas. W ARNING! After using the jack and to[...]

It is recommended that you stow the flat or spar e to avoid tangling the loose cable. NOTE: The winch mechanism is designed for use with the jack extension tube only . Use of an air wrench or other power tools is not recommended and can damage the winch. Tire Changing Procedure W ARNING! Getting under a jacked-up vehicle is dangerous. The vehicle c[...]

Preparations Park the vehicle on a firm level surface, avoiding ice or slippery areas. Set the parking brake and place the gear selector in P ARK (automatic transmission) or REVERSE (manual transmission). On four-wheel drive vehicles, shift the transfer case to the “4L” position. W ARNING! Do not attempt to change a tire on the side of the vehi[...]

Instructions W ARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised. • Apply the parking brake firmly before[...]

Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. NOTE: If the jack will not lower by turning the dial (thumb wheel) by hand, it may be necessary to use the jack drive tube in order to lower the jack. 2500/3500 4X2 Jacking Location WHA T TO DO IN EMERGE[...]

4. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface. W ARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5. Remove the wheel nuts and pull the wh[...]

(SR W) models and 145 ft. lbs. (197 N·m) for 3500 dual rear wheel models. If in doubt about the correct tightness, have them checked with a torque wr ench by your dealer or at a service station. W ARNING! A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Always stow the jack parts and the extra ti[...]

models use the blade on the end of the lug wrench to pry the caps off. The wheel skin can now be r emoved. Y ou must use the flat end of the lug wrench to pry of f the wheel skins. Insert the flat tip completely and using a back and forth motion, loosen the wheel skin. Repeat this procedur e around the tir e until the skin pops off. Replace the whe[...]

Dual wheel models requir e a special heavy-duty lug nut tightening adapter (included with the vehicle) to cor- rectly tighten the lug nuts. Also, when it is necessary to remove and install dual r ear wheels, use a proper vehicle lifting device. NOTE: When installing a spare tir e as part of a dual rear wheel end combination, the tire diameter of th[...]

1. T ighten the wheel nuts in the numbered sequence to a snug fit. 2. Retighten the wheel nuts in the same sequence to the torques listed in the table. Go thr ough the sequence a second time to verify that specific torque has been achieved. Retighten to specifications at 100 miles (160 km) and after 500 miles (800 km). It is recommended that wheel [...]

Attach the wheel wrench to the extension tube. Rotate the winch mechanism until the wheel is drawn into place against the underside of the vehicle. Continue to rotate until you feel the winch mechanism slip or click 3 or 4 times. It cannot be overtightened. Push against the tire several times to be sure it is firmly in place. HOISTING A conventiona[...]

Y our vehicle is equipped with two 12–volt batteries. If it becomes necessary to use a booster battery , with jumper cables, to start a vehicle’s engine because its batteries are discharged, the following pr ocedure should be followed: Set the parking brake and place an automatic transmis- sion in P ARK (or NEUTRAL for a manual transmission). T[...]

W ARNING! Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could result. 2. Connect one end of the other jumper cable to negative (-) post of booster battery . Connect the other end of the jumper cable to a good ground on the engine block of the vehicle with the discharged battery . Make sur[...]

3. T ake care that the clamps fr om one cable do not inadvertently touch clamps from the other cable. Do not lean over the battery when making connection. The negative connection must provide good electrical con- ductivity and current carrying capacity . 4. After the engine is started or if the engine fails to start, cables must be disconnected in [...]

CAUTION! It is very important that the starting unit operating voltage does not exceed 12 V olts D.C. or damage to battery , starter motor , alternator , or electrical system may occur . FREEING A STUCK VEHICLE If vehicle becomes stuck in snow , sand, or mud, it can often be moved by a rocking motion. Move the gear selector rhythmically between DRI[...]

W ARNING! Stand clear of vehicles when pulling with tow hooks. T ow straps and chains may break, causing serious injury . CAUTION! T ow hooks are for emergency use only , to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing. Y ou could damage your vehicle. TOWING A DISABLED VEHICLE Proper towing or lift[...]

The manufacturer r ecommends towing with all wheels OFF the ground. Acceptable methods are to tow vehicle on a flatbed or with one end of vehicle raised and the opposite end on a towing dolly . 2–Wheel- Drive V ehicles Provided that the transmission is operable, tow with the transmission in Neutral and the ignition key in the OFF position along w[...]

[...]

MAINT AINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment .................... 3 3 8 ▫ 5.9L HO Cummins T urbo Diesel ........... 3 3 8 䡵 Onboard Diagnostic System (OBD II) ......... 3 3 9 䡵 Replacement Parts ...................... 3 3 9 䡵 Dealer Service ......................... 3 4 0 䡵 Service Information ..................... 3 4 0 䡵 [...]

▫ Front Axle Universal Drive Joints And Pivot Bearings ............................ 3 5 8 ▫ Body Lubrication ..................... 3 5 8 ▫ W indshield W iper Blades ................ 3 5 9 ▫ W indshield W ashers ................... 3 5 9 ▫ Exhaust System ...................... 3 6 0 ▫ Cooling System ....................... 3 6 1 ▫ F a [...]

䡵 Bulb Replacement ...................... 3 8 5 ▫ Headlight (Halogen)/Front Park And T urn Lights ............................. 3 8 5 ▫ T ail, Stop, T urn And Backup Lights ......... 3 8 9 ▫ Center High-Mounted Stoplight W ith Cargo Light .............................. 3 9 1 ▫ Cab T op Clearance Lights — If Equipped .... 3 9 3 ▫ T ail[...]

ENGINE COMP ARTMENT 5.9L HO CUMMINS TURBO DIESEL 338 MAINT AINING YOUR VEHICLE[...]

ONBOARD DIAGNOSTIC SYSTEM (OBD II) CARB emission control vehicles ar e equipped with a sophisticated onboard diagnostic system called OBDII. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating pr operly , your vehicle will provide excellent performance and fuel [...]

DEALER SERVICE Y our dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner . Service manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any pr ocedure yourself. NOTE: Intentional tampering with emissions c[...]

CAUTION! T o maintain your vehicle safely follow these guide- lines: • W atch your vehicle’s mileage and check your Mainte- nance Schedules regularly for r equired servicing. Ex- cessive wear or damage to certain vehicle components can result if r equired services ar e not performed. • If you have your vehicle undercoated, inspect for underco[...]

• If an engine has been operating and the coolant is hot, allow the engine to cool before you slowly loosen the filler cap and relieve the pr essure fr om the cooling system. • T o avoid burns, remember that the engine components will stay hot after the engine is shut off. • Do not use gasoline or other flammable materials to clean parts. Alw[...]

MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there ar e fixed maintenance intervals, there ar e other items that should operate satisfactorily without periodic maintenance. However , if a malfunction of these item[...]

Never operate the engine with oil level below the “ADD” mark or above the upper “SAFE” mark. Change Engine Oil CAUTION! Overfilling or underfilling the crankcase will cause oil aeration or loss of oil pressure. This could dam- age your engine. Road conditions as well as your kind of driving affect the interval at which your oil should be ch[...]

NOTE: Most vehicles are operated under the conditions listed for Schedule ⬙ B. ⬙ Engine Oil Selection 1. Engine Oil Quality Use only oils conforming to API Ser- vice CI-4. A sulfated ash limit is speci- fied for lubrication oil used in Cum- mins engines. Oils with a high ash content may produce deposits on valves that can progr ess to guttering[...]

Engine Oil Filter Refer to Recommended Fluids, Lubricants and Genuine Parts for the correct part number . The engine oil filter should be changed at every engine oil change. Engine Oil And Filter — Change W ARNING! Hot oil can cause personal injury . Operate the engine until the coolant temperature r eaches 140°F (60°C). Shut the engine off. Re[...]

CAUTION! The filtering medium of other aftermarket filters may disintegrate. Debris from failed filters may plug the piston oil cooling nozzles, resulting in scuffed pistons and engine failure. CAUTION! Fill the oil filter element with clean oil before installation. Use the same type oil that will be used in the engine. When filling the oil filter [...]

Cummins T urbo Diesel Fill the engine with the correct grade of new oil. The engine capacity is 1 1 quarts (10.4 liters) in the crankcase and 1 quart (.95 liter) in the lubricating oil filter . Start the engine and operate it at idle for several minutes. Check for leaks at the lubricating oil filter and oil pan drain plug. Run the engine until it h[...]

Engine Air Cleaner Filter CAUTION! All air entering the engine intake must be filtered. The abrasive particles in unfiltered air will cause rapid wear to engine components. The air filter housing on your Diesel Ram is equipped with a Filter Minder™. This is an air flow restriction gauge that will indicate when the filter element needs to be repla[...]

across the filter element incr eases, a yellow disc travels along a graduated scale on the side of the Filter Minder™. The yellow disc will always show the greatest r estriction experienced by the filter element. When the disc reaches the red zone, the filter element may need to be r eplaced. There is no other time or mileage interval for changin[...]

CAUTION! Many aftermarket performance air filter elements do not adequately filter the air entering the engine. Use of such filters can severely damage your engine. Draining Fuel/W ater Separator Filter CAUTION! Do not drain the fuel/water separator filter when the engine is running. Drain a small amount from the fuel/water separator filter periodi[...]

If more than a couple ounces of fuel has been drained, follow the directions below for “Priming if the engine has run out of fuel.” W ARNING! Do not open the high pressure fuel system with the engine running. Engine operation causes high fuel pressure. High pressure fuel spray can cause serious injury or death. Priming if the engine has run out[...]

CAUTION! Diesel fuel will damage black top paving surfaces. Drain the filter into an appropriate container . W ARNING! Do not use alcohol or gasoline as a fuel blending agent. They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel. CAUTION! Due to lack of lubricants in alcohol or gasoline, the use of[...]

Maintenance Free Batteries The top of the maintenance free batteries ar e perma- nently sealed. Y ou will never have to add water , nor is periodic maintenance requir ed. T o determine the battery charge, check the battery test indicator (if equipped) on top of each battery . If the test indicator (if equipped) appears light or yellow , replace the[...]

W ARNING! Battery posts, terminals, and related accessories con- tain lead and lead compounds. Always wash hands after handling the battery . Battery Blanket Usage A battery loses 60% of its cranking power as the battery temperature decr eases to 0°F (-18°). For the same de- crease in temperatur e, the engine requir es twice as much power to cran[...]

W ARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the W arranty Information b[...]

W ARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary , add fluid to restore to the pr oper indicated level. W ith a clean cloth, wipe any spilled fluid f[...]

Front Prop Shaft Lubrication Lubricate the front driveshaft gr ease fitting at each oil change listed in the appropriate Maintenance Schedule for your vehicle (Schedule “A” and “B”). Use Mopar 威 type MS-6560 (lithium based grease), or equivalent. Front Axle Universal Drive Joints And Pivot Bearings The front axle universal joint and pivot[...]

amount of a high quality lubricant such as Mopar 威 Lock Cylinder Lubricant directly into the lock cylinder . Windshield Wiper Blades The rubber edges of the wiper blades and the windshield should be cleaned periodically with a sponge or soft cloth and a mild nonabrasive cleaner . This will remove accu- mulations of salt or road film. Operation of[...]

After the engine has warmed, operate the defroster for a few minutes to reduce the possibility of smearing or freezing the fluid on the cold windshield. Mopar All W eather W indshield W asher Solution, used with water as directed on the container , aids cleaning action, reduces the freezing point to avoid line clogging, and is not harmful to paint [...]

of the exhaust system abnormally contacts the under- body hardwar e, the isolator and/or hanger should be replaced. Cooling System Cooling System Maintenance At the intervals shown in the Maintenance Schedules Section of the manual, the system should be drained, flushed and filled. Inspection Check engine coolant (antifreeze) pr otection every 12 m[...]

operating temperature, the level of the coolant on the coolant bottle should be between the fluid level marks. Check the coolant level whenever the hood is raised. The radiator normally remains completely full, so ther e is no longer a need to remove the coolant pr essure cap except for checking coolant freeze point or r eplacement with new antifre[...]

NOTE: It is the owner’s responsibility to maintain the proper level of pr otection against freezing accor ding to the temperatures occurring in the ar ea where the vehicle is operated. NOTE: Mixing coolant types will decrease the life of the engine coolant and will requir e more fr equent coolant changes. When additional coolant is needed to main[...]

CAUTION! • Mixing of coolants other than specified engine coolant, may result in engine damage, and de- crease corrosion protection. If a non-HOA T cool- ant is introduced into the cooling system in an emergency , it should be replaced with the speci- fied coolant as soon as possible. • Do not use plain water alone or alcohol base engine coolan[...]

W ARNING! Never add coolant when the engine is overheated. Do not loosen or remove the pressure cap to cool an overheated engine. Heat causes pressure build up in the cooling system. T o prevent scalding or injury , do not remove the pressure cap while the system is hot or under pressure. CAUTION! Recheck the cooling system to insure total system i[...]

degrees Fahr enheit. This cooling process enables mor e efficient burning of fuel r esulting in fewer emissions. T o guarantee optimum performance of the system, keep the surfaces of the charge air cooler , condenser and radiator clean and free of debris. Periodically check the hoses leading to and from the char ge air cooler for cracks or loose cl[...]

Brake Master Cylinder The fluid level of the master cylinder should be checked when performing under the hood service, or immedi- ately if the brake system warning lamp indicates system failure. The brake master cylinder has a translucent plastic reservoir . On the outboard side of the r eservoir , there is a “FULL” dot and an “ADD” dot. Th[...]

W ARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Use only brake fluid that has been in a tightly closed container to avoid contamination from for eign matter or moisture. CAUTION! Do not allow a petroleum-base fluid to contaminate the brake fluid. Seal damage a[...]

Clutch Hydraulic System The clutch hydraulic system is a sealed maintenance-free system. In the event of leakage or other malfunction, the system must be replaced. Rear Axle And 4x4 Front Driving Axle Fluid Level For Model 9.25 Front Axles and 10.5”/1 1.5” Rear Axles refer to Recommended Fluids, Lubricants and Genuine Parts for the correct lubr[...]

T ransfer Case — If Equipped Fluid Level Check This fluid level can be checked by removing the filler plug. The fluid level should be to the bottom edge of the filler plug hole with the vehicle in a level position. Lubricant Selection Refer to Recommended Fluids, Lubricants and Genuine Parts for the correct lubricant type. Manual T ransmission ?[...]

Procedure For Checking Fluid Level T o properly check the automatic transmission fluid level, the following procedur e must be used: 1. The vehicle must be on level ground. 2. The engine should be running at curb idle speed for a minimum of 60 seconds. 3. Fully apply parking brake. 4. Place the gear selector briefly in each gear position ending wit[...]

CAUTION! Using a transmission fluid other than the manufac- turers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder . Using a transmission fluid other than the manufacturers recommended fluid will result in more frequent fluid and filter changes. Refer to Recommended Fluids, Lubricants and Genu[...]

NOTE: If the transmission is disassembled for any reason, the fluid and filter should be changed, and the bands adjusted (if equipped). Special Additives The manufacturer r ecommends against the addition of any additives to the transmission. Exception to this policy is the use of special dyes to aid in detecting fluid leaks. The use of transmission[...]

There ar e two groups identified: those for wheel bearings (Letter “G”) and those for chassis (Letter “L”) lubrication. Perfor- mance categories within these groups r esult in dual letter designations for each group. The letter des- ignations shown in the ex- ample are the highest quality level available and when combined as shown can be us[...]

Required Maintenance For Noise Control Systems The following maintenance services must be performed every 6 months or 6,000 miles (9 600 km), whichever comes first, to assure pr oper operation of the noise control systems. In addition, inspection and service should be performed anytime a malfunction is observed or suspected. Proper maintenance of t[...]

T ampering With Noise Control System Prohibited Federal law prohibits the following acts or the causing thereof: (1) the r emoval or rendering inoperative by any person, other than for purposes of maintenance, repair , or replacement, of any device or element of design incorpo- rated into any new vehicle for the purpose of noise control prior to it[...]

assembly or in any part, component or system of the vehicle as manufactured by the manufactur er , which, at the time it left the manufacturer’s contr ol, caused noise emissions to exceed Federal standards, ar e covered by this warranty for the life of the vehicle. Maintenance Log and Service Chart — 24 V alve Cummins T urbo Diesel Noise System[...]

Noise Systems Maintenance Chart and Service Log — Insert Month, Day , Y ear under column mileage closest to the mileage at which service was performed. MILES 67,500 75,000 82,500 90,000 97,500 84,000 105,00 1 12,500 KILOMETERS 108 000 120 000 132 000 144 000 126 000 156 000 168 000 181 000 Exhaust system-inspect Air cleaner assembly-inspect ODOME[...]

Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion V ehicle body care requir ements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and r oad surfaces during other seasons, are highly corrosive to the metal in your vehi[...]

CAUTION! Do not attempt to fold th e7x1 0 inch trailer towing mirrors forward. Th e7x1 0 inch trailer towing mirrors are not designed to be folded forward and doing so will damage the mirrors and/or vehicle. • If insects, tar or other similar deposits have accumu- lated on your vehicle, wash it as soon as possible. • Use Mopar auto polish to re[...]

• If your vehicle is damaged due to an accident or similar cause which destroys the paint and pr otective coating have your vehicle repair ed as soon as possible. The cost of such repairs is consider ed the responsibil- ity of the owner . • All wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned r egularly with[...]

and Mopar T otal Clean. Care should be taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, deter- gents, or ammonia based cleaners to clean your leather upholstery . Application of a leather conditioner is not requir ed to maintain the original condition. W ARNING! Do not use [...]

Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water . Do not remove the belts fr om the car to wash them. Replace the belts if they appear frayed or worn or [...]

2. Use specified fuses only . 3. Always properly reinstall the cover . VEHICLE STORAGE If you are storing your vehicle for mor e than 21 days, we recommend that you take the following steps to mini- mize the drain on your vehicle’s battery: • Disconnect the Ignition-Off Draw fuse (I.O.D.) fuse located in the Fuse and Relay Center , located in t[...]

BULB REPLACEMENT Headlight (Halogen)/Front Park and T urn Lights CAUTION! This is a halogen bulb. A void touching the glass with your fingers. Reduced bulb life will result. 1. Remove the expanding fastener from the headlight welt. MAINT AINING YOUR VEHICLE 385 7[...]

2. Remove the three (3) bolts from the headlight housing. NOTE: The lower bolt on the driver side headlight also retains the ambient temperatur e sensor between the headlight assembly and the frame. 386 MAINT AINING YOUR VEHICLE[...]

MAINT AINING YOUR VEHICLE 387 7[...]

3. Pull the housing out from the fender to allow room to disconnect the electrical connectors. 4. Unlock and pull connector straight from the base of the headlight halogen bulb. 5. T wist connector on turn signal/park light bulb 1 ⁄ 4 turn and remove connector and bulb fr om housing. 6. Remove housing from vehicle with headlight halogen bulb in h[...]

T ail, Stop, T urn and Backup Lights 1. Remove the two (2) screws that pass through the bed sheetmetal. 2. Pull the housing straight out from the body , with a quick motion, to separate the housing from the body . If not pulled straight, locators may be damaged. 3. Push the red lock slide in on the connector and remove the housing from the vehicle.[...]

4. Remove the four (4) screws from the bulb strip in the housing. 5. Pull the appropriate bulb straight from the bulb strip. • T op Bulb: Park/T urn/Hazard • Center Bulb: Stop/Park/Sidemarker • Bottom Bulb: Backup Lights 390 MAINT AINING YOUR VEHICLE[...]

6. Reverse procedure for installation of bulbs and hous- ing. 7. While holding the taillight firmly in place, fasten the top screw first. Center High-Mounted Stoplight With Cargo Light 1. Remove the two (2) screws holding the housing/lens to the body as shown. MAINT AINING YOUR VEHICLE 391 7[...]

2. Separate the connector holding the housing and wir- ing harness to the body . 3. T urn desired bulb socket 1 ⁄ 4 turn and remove socket and bulb from housing. 4. Pull desired bulb straight from the socket. • Outside Bulbs: Cargo Lamps • Inside Bulb: Center High Mount Stop Lamp 5. Reverse procedure for installation of bulbs and hous- ing. 3[...]

Cab T op Clearance Lights — If Equipped 1. Remove the two screws from the top of the light. 2. Rotate the socket 1 ⁄ 4 turn and pull it from the light assembly . MAINT AINING YOUR VEHICLE 393 7[...]

3. Pull the bulb straight from it’s socket and replace. T ailgate ID Lights (Dual Rear Wheels) 1. Remove the two screws and housing and access the bulb sockets from the r ear . 394 MAINT AINING YOUR VEHICLE[...]

2. T urn socket 1 ⁄ 4 turn counterclockwise to access the bulb. 3. Pull bulb straight out from socket. 4. Reverse procedure for installation of bulbs and hous- ing. MAINT AINING YOUR VEHICLE 395 7[...]

Side Marker Lights (Dual Rear Wheels) 1. Push rearward on the side marker light assembly . 2. Pull the entire assembly from the fender . 3. T urn socket 1 ⁄ 4 turn counterclockwise and r emove from assembly to access the bulb. 4. Pull bulb straight out from socket. 5. Reverse procedure for installation of bulbs and hous- ing. Fog Lights 1. Reach [...]

2. Pull bulb straight from the connector . 3. Reverse procedure for installation of bulbs and hous- ing. FLUID CAP ACITIES FLUID CAP ACITIES U.S. Metric Fuel 2500 Shortbed Models 34 gal. 128L 2500 Longbed Models 35 gal. 132L 3500 Shortbed Models 34 gal. 128L 3500 Longbed Models 35 gal. 132L Engine Oil 5.9L Diesel Engine I-6 12.0 qts. 1 1.4L Cooling[...]

RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) P/N 501 1764AB or equivalent. Engine Oil For the proper quality and SAE Grade oil for your engine, r efer to the section ⬙ Ma[...]

Chassis Component Fluids, Lubricants and Genuine Parts. Automatic T ransmission Mopar 威 A TF+4, Automatic T ransmission Fluid or equivalent. T ransfer Case Mopar 威 A TF+4, Automatic T ransmission Fluid or equivalent. Manual T ransmission Fluid NV 4500 Mopar 威 75W -85 Synthetic, API grade GL4, Mopar P/N 4874459 or equiva- lent Manual T ransmis[...]

[...]

MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ........ 4 0 2 䡵 Maintenance Schedules — 24–V alve Cummins T urbo Diesel .......................... 4 0 2 ▫ Schedule “B” ........................ 4 0 5 ▫ Schedule “A” ........................ 4 1 6 8 M A I N T E N A N C E S C H E D U L E S[...]

EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type in this section (Section 8) must be done at the times or mileages specified to assure the continued pr oper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best ve[...]

• Off-r oad or desert operation. • Extensive operation at high engine speeds (greater than 2900 rpm) and loads (greater than 70% thr ottle). NOTE: Most vehicles are operated under the conditions listed for Schedule ⬙ B ⬙ . NOTE: If ANY of these apply to you then change your coolant every 102,000 miles (163 000 km) or 60 months, whichever co[...]

Once a Month • Check tire pr essure and look for unusual wear or damage. • Inspect the batteries and clean and tighten the termi- nals as requir ed. • Check the fluid levels of coolant reservoir , brake master cylinder , and transmission and transfer case (if equipped), add as needed. • Check Filter Minder™. Replace air cleaner filter ele[...]

Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Frequent short trips wher e the engine does not achieve full operating temperature (operating temperatur e de- fined as 190° F (66° C) coolant temperature). • Extensive engine idling (over 10 minutes per hour of operat[...]

Miles 3,750 7,500 1 1,250 15,000 18,750 (Kilometers) (6 000) (12 000) (18 000) (24 000) (30 000) Change engine oil and engine oil filter . X X Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). X X XXX Rotate tires. X X Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only . XX Inspect water pump weep hole for blockage. X Replace fuel filte[...]

Miles 22,500 26,250 30,000 33,750 37,500 (Kilometers) (36 000) (42 000) (48 000) (54 000) (60 000) Change engine oil and engine oil filter . X X X Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). X X X X X Rotate tires. X X X Lubricate outer tie rod ends 2500/3500 (4X4) models only . X X X Inspect drive belt, replace as r equired. X Inspect fa[...]

Miles 41,250 45,000 48,750 52,500 56,250 (Kilometers) (66 000) (72 000) (78 000) (84 000) (90 000) Change engine oil and engine oil filter . X X Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). X X XXX Rotate tires. X X Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only . XX Inspect drive belt, replace as r equired. X Inspect water pum[...]

Miles 60,000 63,750 67,500 71,250 75,000 (Kilometers) (96 000) (102 000) (108 000) (1 14 000) (120 000) Change engine oil and engine oil filter . X X X Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). X X XXX Flush and replace engine coolant at 60 months, if not replaced at 102,000 miles (163 000 km). X Rotate tires. X X X Lubricate outer tie [...]

Miles 60,000 63,750 67,500 71,250 75,000 (Kilometers) (96 000) (102 000) (108 000) (1 14 000) (120 000) Change front axle fluid (4X4). X X Change 6-spd manual transmission (G-56) fluid 2500/3500 models only . X Inspect brake linings. X X Inspect and adjust parking brake if necessary . X X Drain and refill transfer case fluid (4X4). X Drain and refi[...]

Miles 78,750 82,500 86,250 90,000 93,750 (Kilometers) (126 000) (132 000) (138 000) (144 000) (150 000) Change engine oil and engine oil filter . X X Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). X X XXX Rotate tires. X X Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only . XX Inspect drive belt, replace as r equired. X Change rear [...]

Miles 78,750 82,500 86,250 90,000 93,750 (Kilometers) (126 000) (132 000) (138 000) (144 000) (150 000) Inspect front wheel bearings. X Inspect brake linings. X Inspect and adjust parking brake if necessary . X Drain and refill automatic transmission fluid. Re- place filter and adjust bands (48RE only). X 412 SCHEDULE “B” 8 M A I N T E N A N C [...]

Miles 97,500 100,000 101,250 105,000 108,750 112,500 (Kilometers) (156 000) (160 000) (162 000) (168 000) (174 000) (180 000) Change engine oil and engine oil filter . X X X Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). X X XXXX Flush and replace engine coolant, if not r eplaced at 60 months. X Rotate tires. X X X Lubricate outer tie rod en[...]

Miles 1 16,250 120,000 123,750 127,500 131,250 135,000 (Kilometers) (186 000) (192 000) (198 000) (204 000) (210 000) (216 000) Change engine oil and engine oil filter . X X X Lubricate Front Drive Shaft Fitting (2500/ 3500, 4X4). X X XXXX Rotate tires. X X X Flush and replace engine coolant at 120 months, if not replaced at 102,000 miles (163 000 [...]

Miles 1 16,250 120,000 123,750 127,500 131,250 135,000 (Kilometers) (186 000) (192 000) (198 000) (204 000) (210 000) (216 000) Replace fuel filter element. Clean the water in fuel sensor . XX Inspect front wheel bearings. X Change rear axle fluid. X X Change front axle fluid (4X4). X X Change 6-spd manual transmission (G-56) fluid 2500/3500 models[...]

Schedule “A” Miles 7,500 15,000 22,500 30,000 37,500 (Kilometers) (12 000) (24 000) (36 000) (48 000) (60 000) [Months] [6] [12] [18] [24] [30] Change engine oil and engine oil filter . X X Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). X X X X X Rotate tires. X X X X X Lubricate outer tie rod ends 2500/3500 (4X4) models only . X X X X X[...]

Miles 45,000 52,500 60,000 67,500 75,000 (Kilometers) (72 000) (84 000) (96 000) (108 000) (120 000) [Months] [36] [42] [48] [54] [60] Change engine oil and engine oil filter . X X X Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). X X XXX Rotate tir es. X X X X X Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only . X X XXX Check trans[...]

Miles 45,000 52,500 60,000 67,500 75,000 (Kilometers) (72 000) (84 000) (96 000) (108 000) (120 000) [Months] [36] [42] [48] [54] [60] Inspect fan hub. X Inspect damper . X Inspect front wheel bearings. X Replace fuel filter element. Clean the water in fuel sensor X 418 SCHEDULE “A” 8 M A I N T E N A N C E S C H E D U L E S[...]

Miles 82,500 90,000 97,500 100,000 105,000 (Kilometers) (132 000) (144 000) (156 000) (160 000) (168 000) [Months] [66] [72] [78] [84] Change engine oil and engine oil filter . X X Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). X X XXX Rotate tir es. X X X X X Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only . X X XXX Flush and rep[...]

Miles 82,500 90,000 97,500 100,000 105,000 (Kilometers) (132 000) (144 000) (156 000) (160 000) (168 000) [Months] [66] [72] [78] [84] Inspect front wheel bearings. X Inspect brake linings. X Inspect and adjust parking brake if necessary . X Drain and refill automatic transmission fluid. Re- place filter and adjust bands (48 RE only). X 420 SCHEDUL[...]

Miles 1 12,500 120,000 127,500 135,000 142,500 150,000 (Kilometers) (181 000) (193 000) (205 000) (217 000) (229 000) (241 000) [Months] [90] [96] [102] [108] [1 14] [120] Change engine oil and engine oil filter . X X X Lubricate Front Drive Shaft Fitting (2500/ 3500, 4X4). X X XXXX Rotate tir es. X X X X X X Lubricate outer tie rod ends 2500/3500 [...]

Miles 1 12,500 120,000 127,500 135,000 142,500 150,000 (Kilometers) (181 000) (193 000) (205 000) (217 000) (229 000) (241 000) [Months] [90] [96] [102] [108] [1 14] [120] Replace fuel filter element. Clean the water in fuel sensor . XX X Inspect front wheel bearings. X X Inspect brake linings. X X Inspect and adjust parking brake if necessary . X [...]

IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .............................. 4 2 4 ▫ Prepar e For The Appointment ............ 4 2 4 ▫ Prepar e A List ........................ 4 2 4 ▫ Be Reasonable W ith Requests ............. 4 2 4 䡵 If Y ou Need Assistance ................... 4 2 4 䡵 [...]

SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional charges with the service manager . Keep a maintenance log of your vehicle’s[...]

This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you ar e still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact t[...]

Center . Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHR Y . Service Contract Y ou may have purchased a service contract for your vehicle to help protect you fr om the high cost of unex- pected repairs aft[...]

U.S. V ehicles Only IF YOU NEED CONSUMER ASSIST ANCE 427 9[...]

MOP AR 姞 P ARTS Mopar 威 fluids, lubricants, parts, and accessories are available from your dealer . They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and W ashington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immedi[...]

PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Express, and Discover or ders are ac- cepted. If you prefer mailing your payment, please call for an order form. NOTE: A street addr ess is required when or dering manuals. (No P .O. Boxes). •[...]

Call T oll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1 143 (Canada) Or V isit us on the W orld Wide W eb at: • www .techauthority .daimlerchrysler .com • www .daimlerchrysler .ca/manuals 430 IF YOU NEED CONSUMER ASSIST ANCE[...]

INDEX 10[...]

Air Cleaner , Engine (Engine Air Cleaner Filter) . 349,375 Air Conditioner Maintenance ............... 3 5 5 Air Conditioning Refrigerant ............. 355,356 Air Conditioning System ................ 207,355 Air Conditioning System, Zone Control ........ 2 1 1 Air Filter .............................. 3 4 9 Air Pressur e, T ires ..................[...]

Body Mechanism Lubrication ............... 3 5 8 B-Pillar Location ........................ 2 6 4 Brake Fluid ............................ 3 9 9 Brake System ........................ 256,366 Anti-Lock ........................... 2 5 7 Disc Brakes .......................... 3 6 6 Fluid Check .......................... 3 6 7 Hoses ...................[...]

Child Seat ............................ 56,62 Cigar Lighter ........................... 1 4 4 Climate Control ......................... 2 0 4 Clock ................................ 1 7 0 Clutch Linkage Maintenance ................ 3 6 8 Compact Disc Maintenance ................. 2 0 3 Compact Disc Player .................. 177,183 Compact Spare T i[...]

Used Coolant ......................... 3 6 4 Door Ajar ............................. 1 6 4 Door Locks ............................. 1 6 Door Opener , Garage ..................... 1 3 4 Draining Fuel/W ater Separator Filter .......... 3 5 1 Drive Belts ............................ 3 4 8 Dual Rear Wheels ..................... 280,324 Electric Rear W [...]

Exterior Lighting ........................ 1 1 6 F a n .................................. 3 6 5 Filters Engine Oil ..................... 343,346,398 Flashers T urn Signal .......................... 1 1 8 Flat T ire Stowage ..................... 317,326 Fluid, Brake ........................... 3 9 9 Fluid Capacities ......................... 3 9 7 F[...]

Glass Cleaning .......................... 3 8 2 GVWR ............................... 2 8 6 Hands-Free Phone ........................ 8 3 Hazard W arning Flasher ................... 3 1 4 Head Restraints ......................... 1 0 8 Headlights .......................... 1 16,385 High Beam ........................... 1 1 9 High Beam/Low Beam Selec[...]

Jack Location ........................... 3 1 6 Jack Operation .......................... 3 1 8 Jump Starting .......................... 3 2 7 Key , Replacement ........................ 1 2 Key , Sentry ............................. 1 1 Key-In Reminder ......................... 1 1 Keyless Entry System ...................... 2 2 Keys ..............[...]

Low W asher Fluid ..................... 1 6 8 Passing ............................. 1 1 9 Seat Belt Reminder ..................... 1 6 3 Service ........................... 384,385 Side Marker .......................... 3 9 6 T ransfer Case ......................... 2 4 7 T ransmission W arning ................ 169,298 T urn Signal ................[...]

T railer T owing ...................... 81,296 Modifications/Alterations, V ehicle ............. 8 Mopar Parts ......................... 339,428 Multi-Function Control Lever ............... 1 1 8 New V ehicle Break-In Period ................ 6 7 Noise Control Maintenance .......................... 3 7 5 T ampering Prohibited ................... 3 7[...]

Phone, Cellular .......................... 8 3 Phone, Hands-Free ....................... 8 3 Pickup Box ............................ 1 5 1 Placard, T ire and Loading Information ......... 2 6 5 Power Distribution Center ..................... 3 8 3 Door Locks ........................... 1 7 Mirrors .............................. 8 0 Outlet .........[...]

Restraint, Head ......................... 1 0 8 Restraints, Child ....................... 56,62 Rotation, T ires .......................... 2 7 9 Safety Checks Inside V ehicle ................. 7 0 Safety Checks Outside V ehicle ............... 7 0 Safety Defects, Reporting .................. 4 2 8 Safety Information, T ire ................... 2 6 [...]

T ransfer Case ......................... 2 4 6 T ransfer Case, Shifting into T ransfer Case Neutral (N) .................. 303,306 T ransfer Case, Shifting out of T ransfer Case Neutral (N) .................. 305,308 Shoulder Belt Upper Anchorage .............. 4 1 Shoulder Belts ........................... 3 4 Side Airbag .........................[...]

T ire Safety Information .................... 2 6 0 T i r e s ............................... 70,268 Air Pressur e .......................... 2 6 8 Alignment ........................... 2 7 6 Chains .............................. 2 7 6 Changing ............................ 3 1 7 Compact Spare ........................ 2 7 2 Dual ....................[...]

T i p s ................................ 2 9 7 T railer and T ongue W eight ................ 2 9 4 T railer T owing Guide ..................... 2 9 5 T railer W eight .......................... 2 9 5 T ransfer Case Fluid ............................... 3 9 9 T ransmission Automatic ........................ 237,370 Fluid ............................[...]

W ind Buffeting ....................... 33,142 W indow Airbag .......................... 5 4 W indow Fogging ........................ 2 1 5 W indows .............................. 3 1 Power ............................... 3 1 Rear Sliding ........................... 3 2 W indshield Defroster .................. 206,209 W indshield W ashers .........[...]

NOTES[...]

NOTES[...]