Draytek Vigor 2130n manual

[...]

Vigor2130 Series User’s Guide ii Vigor2130 Series High Speed Gigabit Router User’s Guide Version: 1.2 Firmware Version: V1.3.0.1 Date: 29/04/2010[...]

Vigor2130 Series User’s Guide iii Copyright Information Copyright Declarations Copyright 2010 All rights reserved. This pub lication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stor ed in a retrieval system, or translated into any language withou t written permission from the copyright[...]

Vigor2130 Series User’s Guide iv European Community Declarations Manufacturer: DrayTek Corp. Address: No. 26, Fu Shing Road, HuKou County, H sinChu Industrial Park, Hsin-Chu, Taiwan 303 Product: Vigor2130 Ser ies Router DrayTek Corp. declares that Vigor2130 Series of ro uters are in compliance with the following essential requirements and other r[...]

Vigor2130 Series User’s Guide v T T a a b b l l e e o o f f C C o o n n t t e e n n t t s s 1 Pref ace ............................................................................................................... 1 1.1 Web Conf iguration Bu ttons Explanation ................................................................................. 1 1.2[...]

Vigor2130 Series User’s Guide vi 3.3.2 Open Ports ............................................................................................................... ....... 54 3.3.3 DM Z Host ................................................................................................................. ....... 55 3.4 Bandwidt h Management ........[...]

Vigor2130 Series User’s Guide vii 4.1.1 Inter net Access .......................................................................................................... ... 111 4.1.2 Po rts.................................................................................................................... .......... 117 4.1.3 3G Backup ................[...]

Vigor2130 Series User’s Guide viii 4.10.1 IPv6 WA N Setup ......................................................................................................... 1 87 4.10.2 IPv6 LAN Se tup .......................................................................................................... 191 4.10.3 IPv6 Fi rewall Se tup ................[...]

Vigor2130 Series User’s Guide 1 1 P P r r e e f f a a c c e e The Vigor2130 series are the routers with high speed in data transmission through WAN port and LAN ports. With hardware NAT acceleration, the rate of Vigor2130 series can be greater than 900Mbps almost. With the development of NGN (Next Generation Network), you may recently hear the ne[...]

Vigor2130 Series User’s Guide 2 1 1 . . 2 2 L L E E D D I I n n d d i i c c a a t t o o r r s s a a n n d d C C o o n n n n e e c c t t o o r r s s Before you use the Vigor router, please get acquainted with the LED indicators and connectors first. 1 1 . . 2 2 . . 1 1 F F o o r r V V i i g g o o r r 2 2 1 1 3 3 0 0 LED Status Explanation Blinking[...]

Vigor2130 Series User’s Guide 3 Interface Description Factory Reset Restore the default settings. Usage: Tu rn on t he router (ACT LED is blinking). Press the hole and keep for m ore than 5 seconds . When you see t he ACT LED begins to blink rapidly than usual, release th e butto n. Then the router will restart with the factory default con figura[...]

Vigor2130 Series User’s Guide 4 1 1 . . 2 2 . . 2 2 F F o o r r V V i i g g o o r r 2 2 1 1 3 3 0 0 n n LED Status Explanation Blinking The router i s powered on and running normally . ACT (Activity) Off The router is powe red off. On Hardware NAT is enab led. HPA Off Hard ware NAT is disabled. On (Orange) The port is connected with 100Mbps. On ([...]

Vigor2130 Series User’s Guide 5 Interface Description Factory Reset Restore the default settings. Usage: Tu rn on t he router (ACT LED is blinking). Press the hole and keep for m ore than 5 seconds . When you see t he ACT LED begins to blink rapidly than usual, release th e button. Then the router will restart with the factory default configurati[...]

Vigor2130 Series User’s Guide 6 1 1 . . 2 2 . . 3 3 F F o o r r V V i i g g o o r r 2 2 1 1 3 3 0 0 V V n n LED Status Explanation Blinking The router i s powered on and running normally . ACT (Activity) Off The router is powe red off. On Hardware NAT is enab led. HPA Off Hard ware NAT is disabled. On (Orange) The port is connected with 100Mbp s.[...]

Vigor2130 Series User’s Guide 7 Interface Description Phone2/P hone1 Connector of analog phon e for VoIP communicatio n . Factory Reset Restore the default settings. Usage: Tu rn on t he router (ACT LED is blinking). Press the hole and keep for m ore than 5 seconds . When you see t he ACT LED begins to blink rapidly than usual, release th e butto[...]

Vigor2130 Series User’s Guide 8 1 1 . . 3 3 H H a a r r d d w w a a r r e e I I n n s s t t a a l l l l a a t t i i o o n n Before starting to configure the router, you have to connect your devices correctly. 1. Connect Line port to land line jack with a RJ-11 cable (Vn model). 2. Connect this device to a modem with an Ethernet cable. 3. Connect [...]

Vigor2130 Series User’s Guide 9 S S t t a a n n d d I I n n s s t t a a l l l l a a t t i i o o n n The Vigor2130 must be placed erectly. Therefore you have to install a stand onto the router to make it standing firmly. Please follow the figures listed below to finish the installation. c d e f[...]

Vigor2130 Series User’s Guide 10 1 1 . . 4 4 P P r r i i n n t t e e r r I I n n s s t t a a l l l l a a t t i i o o n n You can install a printer onto the router for shar ing printing. All the PCs connected this router can print documents via the router. The exam ple provided here is made based on Windows XP/2000. For Windows 98/SE/Vista, please[...]

Vigor2130 Series User’s Guide 11 4. Click Local printer attached to this computer and click Next. 5. In this dialog, choose Create a new port Type of port and use the drop down list to select Standard TCP/IP Port . Click Next .[...]

Vigor2130 Series User’s Guide 12 6. In the following dialog, type 192.168.1.1 (router’s LAN IP) in the field of Printer Name or IP Address and type IP_192.168.1.1 as the port name. Then, click Next . 7. Click Standard and choose Generic Network Card. 8. Then, in the following dialog, click Finish .[...]

Vigor2130 Series User’s Guide 13 9. Now, your system will ask you to choose right na me of the printer t hat you installed onto the router. Such step can make correct driver loaded onto your PC. When you finish the selection, click Next . 10. For the final stage, you need to go back to Control Panel-> Printers and edit the property of the new [...]

Vigor2130 Series User’s Guide 14 The printer can be used for printing now. Most of the printers with different manufacturers are compatible with vigor router. Note 1: Some printers with the fax/scanning or other additional fun ctions are not supported. If you do not know whether your pr inter is supported or not, please vi sit www.draytek.com to [...]

Vigor2130 Series User’s Guide 15 2 C C o o n n f f i i g g u u r r i i n n g g B B a a s s i i c c S S e e t t t t i i n n g g s s For using the router properly, it is necessar y for you to change the password of web configuration for security and adjust primary basic settings. 2 2 . . 1 1 T T w w o o - - L L e e v v e e l l M M a a n n a a g g e[...]

Vigor2130 Series User’s Guide 16 2 2 . . 3 3 C C h h a a n n g g i i n n g g P P a a s s s s w w o o r r d d No matter user mode operation or admin mode operation, please change the password for the original security of the router. 1. Open a web browser on your PC and type http://192. 168.1.1. A pop-up window will open to ask for username and pas[...]

Vigor2130 Series User’s Guide 17 4. Go to System Maintenance page and choose System Password/User Password . Or 5. Type New Password in New Password and Confirm New Password fields. Then click OK to continue. 6. Now, the password has been changed. Next time, use the new password to access the Web Configurator for this router.[...]

Vigor2130 Series User’s Guide 18 2 2 . . 4 4 Q Q u u i i c c k k S S t t a a r r t t W W i i z z a a r r d d Notice: Quick Start Wizard for user mode operation is the same as for admin mode operation. If your router can be under an environment with high speed NAT, the configuration provide here can help you to deploy and use the router quickl y. [...]

Vigor2130 Series User’s Guide 19 2 2 . . 4 4 . . 2 2 S S e e t t t t i i n n g g u u p p t t h h e e T T i i m m e e Z Z o o n n e e On the next page as shown below, please select the Time Zone for the router installed and specify the NTP server(s). Then click Next for next step. 2 2 . . 4 4 . . 3 3 S S e e t t t t i i n n g g u u p p t t h h e e[...]

Vigor2130 Series User’s Guide 20 S S t t a a t t i i c c I I P P You will receive a fixed public IP address or a public subnet, namely m ultiple public IP addresses from your DSL or Cable ISP service providers. In most cases, a Cable service provider will offer a fixed public IP, while a DSL service provider will offer a public subnet. If you hav[...]

Vigor2130 Series User’s Guide 21 D D H H C C P P It is not necessary for you to type any IP addr ess manually. Simply choose this type and the system will obtain the IP address automatically from DHCP server. Enable The router will detect the MAC address automatically. Or, check the box to enable MAC address cloning. Clone MAC Address It is avail[...]

Vigor2130 Series User’s Guide 22 If your ISP provides you the PPPoE connection, please select PPPoE for this router. The following page will be shown: User Name Assign a specific valid user name provided by the ISP. Password Assign a valid password provided by the ISP. Redial Policy If you want to connect to Internet all the time, you can choose [...]

Vigor2130 Series User’s Guide 23 P P P P T T P P / / L L 2 2 T T P P if you click PPTP/L2TP as the protocol, pl ease manually enter the Username/Password provided by your ISP and all the required inform ation. User Name Assign a specific valid user name provided by the ISP. Password Assign a valid password provided by the ISP. Server Address Spec[...]

Vigor2130 Series User’s Guide 24 Clone MAC Address It is available when the box of Enable is checked. Click Clone PC Address. The result will be displayed in the field of MAC Address. After finishing the settings here, please click Next. 2 2 . . 4 4 . . 4 4 S S e e t t t t i i n n g g u u p p t t h h e e W W i i r r e e l l e e s s s s C C o o n [...]

Vigor2130 Series User’s Guide 25 WEP encryption bit size and have the same key . Four keys can be entered here, but on ly one key can be selected at a time. The keys can be entered in ASCII or Hexadecimal. Choose the ke y you wish to use by using the Default Key drop down list.[...]

Vigor2130 Series User’s Guide 26 W W P P A A - - P P S S K K If you choose WPA-PSK as the security configuration, you have to specify WPA mode, algorithm and pre-shared key. Type The WPA encrypts each frame transmitted from the radio using the key, which either PSK (Pre-Shared Key) entered manually in this field below or automatically negotiated [...]

Vigor2130 Series User’s Guide 27 W W P P A A - - R R A A D D I I U U S S Remote Authentication Dial-In User Servi ce (RADIUS) is a security authentication client/server protocol that supports authenti cation, authorization and accounting, which is widely used by Internet service providers. It is the most common method of authenticating and author[...]

Vigor2130 Series User’s Guide 28 W W P P S S WPS (Wi-Fi Protected Setup) provides easy procedure to m ake network connection between wireless station and wireless access point (vigor router) with the encryption of WPA and WPA2. If you choose WPS as the security configuration, you can press Start WPS PIN and Start WPS PBC to complete the wireless [...]

Vigor2130 Series User’s Guide 29 2 2 . . 4 4 . . 5 5 S S a a v v i i n n g g t t h h e e W W i i z z a a r r d d C C o o n n f f i i g g u u r r a a t t i i o o n n Now you can see the following screen. It indicates that the setup is complete. Different types of connection modes will have different summary. Click Finish and then restart the route[...]

Vigor2130 Series User’s Guide 30 RX Packets Displays the total received packets at the LAN interface. TX Bytes Displays the total transmitted bytes at the LAN interface. RX Bytes Displays the total received packets at the LAN interface. IPv6 Address Displays the IPv6 address of the LAN interface. WAN Status IP Displays the IP address of the WAN i[...]

Vigor2130 Series User’s Guide 31 3 U U s s e e r r M M o o d d e e O O p p e e r r a a t t i i o o n n This chapter will guide users to execute simp le configuration through user mode operation. 1. Open a web browser on your PC and type http://192. 168.1.1. The window will ask for typing username and password. 2. Do not type any word (both userna[...]

Vigor2130 Series User’s Guide 32 W W h h a a t t a a r r e e P P u u b b l l i i c c I I P P A A d d d d r r e e s s s s a a n n d d P P r r i i v v a a t t e e I I P P A A d d d d r r e e s s s s As the router plays a role to manage and further protect its LAN, it interconnects groups of host PCs. Each of them has a private IP address assigned b[...]

Vigor2130 Series User’s Guide 33 3 3 . . 1 1 . . 1 1 I I n n t t e e r r n n e e t t A A c c c c e e s s s s This page allows you to set WAN configura tion with different modes. Use the Connection Type drop down list to choose one of the WAN modes. The corresponding page will be displayed. S S t t a a t t i i c c For static IP mode, you usually r[...]

Vigor2130 Series User’s Guide 34 IP Address Type the IP address. Subnet Mask Type the subnet mask. Gateway IP Address Type the gateway IP address. Primary DNS Server Type in the primary IP address for the router if you want to use Static IP mode. Secondary DNS Server Type in secondary IP address for using in the future if necessary. Mode Such fun[...]

Vigor2130 Series User’s Guide 35 D D H H C C P P DHCP allows a user to obtain an IP address automatically from a DHCP server on the Internet. If you choose DHCP mode, the DHCP server of your ISP will assign a dynamic IP address for your router automatically. It is not necessary for you to assign any setting, Router Name Type in a name for the rou[...]

Vigor2130 Series User’s Guide 36 P P P P P P o o E E To choose PPPoE as the accessing protocol of the internet, please select PPPoE from the Internet Access menu. The following web page will be shown. Username Type in the username provided by ISP in this field. Password Type in the password provided by ISP in this field. Redial Policy If you want[...]

Vigor2130 Series User’s Guide 37 After finishing all the settings here, please click OK to activate them. P P P P T T P P / / L L 2 2 T T P P To use PPTP/L2TP as the accessing protocol of the internet, please choose PPTP/L2TP from Connection Type drop down menu. The following web page will be shown. Username Type in the username provided by ISP i[...]

Vigor2130 Series User’s Guide 38 Redial Policy If you want to connect to Internet all the time, you can choose Always On . Otherwise, choose Connect on Demand and Idle Time Out Set the timeout for breaking down the Internet after passing through the time without any action. When you choose Connect on Demand, you have to type value here. MTU Size [...]

Vigor2130 Series User’s Guide 39 Modem Dial String Such value is used to dial through USB mode. Please use the default value. If you have any question, please contact to your ISP. PPP Username Type the PPP username (optional). PPP Password Type the PPP password (optional). Clone MAC Address It is available when the box of Enable is checked. Click[...]

Vigor2130 Series User’s Guide 40 obeyed. Current Tx: indicates whether pause frames on the port are transmitted. Maximum Frame This module offers 1518~9600 (B ytes) length to make the long packet for data transmission. Excessive Collision Mode There are two modes for yo u to choose when excessive collision happened in half-duplex condition. Disca[...]

Vigor2130 Series User’s Guide 41 SIM PIN code Type PIN code of the SIM card that will be used to access Internet. Modem Initial String1/2 Such value is used to initia lize USB modem. Please use the default value. If you have any question, please contact to your ISP. APN Name APN means Access Point Name which is provided and required by some ISPs.[...]

Vigor2130 Series User’s Guide 42 In some special case, you may have a public IP subnet from your ISP such as 220.135.240.0/24. This m eans th at you can set up a public subnet or call second subnet that each host is equipped with a public IP address. As a part of the public subnet, the V igor router will serve for IP routing to help hosts in th e[...]

Vigor2130 Series User’s Guide 43 Y ou can group local hosts by physical ports and create up to 4 virtual LANs. T o manage the communication between different groups, please set up rules in V irtual LAN (VL AN) function and the rate of each. Below shows the LAN menu:[...]

Vigor2130 Series User’s Guide 44 3 3 . . 2 2 . . 1 1 G G e e n n e e r r a a l l S S e e t t u u p p This page provides you the general settings for LAN. Click LAN to open the LAN settings page and choose General Setup . IP Address T ype in private IP address for connecting to a local private network (Default: 192.168.1.1). Subnet Mask T y pe in [...]

Vigor2130 Series User’s Guide 45 Secondary IP Address Y ou can specify secondary DNS server IP address here because your ISP often provides you more than one DNS Server . If your ISP does not provide it, the router will autom atically apply default secondary DNS Server IP address: 194.98.0.1 to this field. The default DNS Server IP address can be[...]

Vigor2130 Series User’s Guide 46 Auto . Flow Control If flow control is enabled by checking Configured box, bot h parties can send PAUSE frame to the transmitting device(s) if the receiving port is too busy to handle. If not, there will be no flow control in the port. It drops the pac ket if too much to handle. Current Rx: indicates whether pause[...]

Vigor2130 Series User’s Guide 47 3 3 . . 2 2 . . 3 3 M M A A C C A A d d d d r r e e s s s s T T a a b b l l e e This page allows you to set timeouts for en tries in dynamic MAC Table and configure the static MAC table here. Disable Automatic Aging Stop the MAC table aging timer, the learned MAC address will not age out automatically. The default[...]

Vigor2130 Series User’s Guide 48 To add a new static MAC entry, click Add new static entry . A new entry will be shown as follows. Choose VLAN ID and type a new MAC ad dress. Next, s pecify port member for this table. Finally, click OK to save the changes. 3 3 . . 2 2 . . 4 4 V V L L A A N N Virtual LAN function provides you a very convenient way[...]

Vigor2130 Series User’s Guide 49 To add or remove a VLAN, please refer to the following example. 1. VLAN 1 is consisted of hosts linked to P1 ~ P4. 2. After checking the box to enable VLAN func tion, you will check the table according to the needs as shown below. 3. T o remove VLAN, click the Delete button for the one you want to remove and click[...]

Vigor2130 Series User’s Guide 50 3 3 . . 2 2 . . 6 6 S S t t a a t t i i c c R R o o u u t t e e Go to LAN and choose Static Route to open setting page. Index The number (1 to 10) under Index displa ys current static router . Destination Address Display the destination address of the static route. Status Display the status of the static route. Ad[...]

Vigor2130 Series User’s Guide 51 1. Click the LAN - S tatic Route and click Add. Check the Enable box. Please add a static route as shown below , which regulates all p ackets destined to 192.168.10.0 will be forwarded to 192.168.1.2. Click OK . 2. Return to St a t i c R o u t e page. Click Add again to add another static route as show below , whi[...]

Vigor2130 Series User’s Guide 52 Enable Click this radio button to invoke this fu nction. However, IP/MAC which is not listed in IP Bind List also can connect to Internet. Disable Click this radio button to disable this function. All the settings on this page will be invalid. Strict Bind Click this radio button to block the connection of the I P/[...]

Vigor2130 Series User’s Guide 53 Remove You can remove any item listed in IP Bind List . Simply click and select the one, and click Remove . The selected item will be removed from the IP Bind List . Note: Before you select Strict Bind , you have to bind one set of IP/MAC address for one PC. If not, no one of the PCs can access into In ternet. And[...]

Vigor2130 Series User’s Guide 54 3 3 . . 3 3 . . 2 2 O O p p e e n n P P o o r r t t s s Open Ports allows you to open a range of ports for the traffic of special applications. Common application of Open Ports includes P2 P application (e.g., BT, KaZaA, Gnutella, WinMX, eMule and others), Internet Camera etc. Ensure that you keep the application [...]

Vigor2130 Series User’s Guide 55 Local Port (optional) If it is configured, the forwarded traffic is mapped to this port on the local host. 3 3 . . 3 3 . . 3 3 D D M M Z Z H H o o s s t t Vigor router provides a facility DMZ Host that maps ALL unsolicited data on any prot ocol to a single host in the LAN. Regular web surfing a nd other such Inter[...]

Vigor2130 Series User’s Guide 56 3 3 . . 4 4 B B a a n n d d w w i i d d t t h h M M a a n n a a g g e e m m e e n n t t Below shows the menu items for Bandwidth Management. 3 3 . . 4 4 . . 1 1 S S e e s s s s i i o o n n L L i i m m i i t t A PC with private IP address can access to the Internet via NAT router. The router will generate the recor[...]

Vigor2130 Series User’s Guide 57 Start IP Defines the start LAN IP address for limit session. End IP Defines the end LAN IP address for limit session. Sessions Limit Defines the available session number for each host in the specific range of IP addresses. If you do not set the session number in this field, the system will use the default session [...]

Vigor2130 Series User’s Guide 58 Smart Bandwidth Limit Click this radio button to conf igure t he default limitation for bandwidth. When session number exceeds – ty pe the value here as a threshold to apply the smart bandwidth limit. TX limit - Define the default speed of the upstream for each computer in LAN. RX limit - Define the default spee[...]

Vigor2130 Series User’s Guide 59 3 3 . . 4 4 . . 3 3 P P o o r r t t R R a a t t e e C C o o n n t t r r o o l l A policer can limit the bandwidth of received frames. It is located in front of the ingress queue. And a shaper can limit the bandwidth of tran smitted frames. It is located after the ingress queues. This page allows you to configure t[...]

Vigor2130 Series User’s Guide 60 z Scheduling: Based on classification of service level to assign packets to queues and associated service types The basic QoS implementation in Vigor routers is to classify and schedule packets based on the service type information in the IP header. Fo r instance, to ensure the connection with the headquarter, a t[...]

Vigor2130 Series User’s Guide 61 QCE Type Display the type of that QCE (QoS Control Entries). Type Value Display the value specified for the QCE. Traffic Class Display the class of the data transmission for the QCE. QoS Control List allows users to set up to five groups of QCL. Each QCL group c an contain 12 QCE settings. A A d d d d i i n n g g [...]

Vigor2130 Series User’s Guide 62 Ethernet Type Value Either 8~63 ASCII characters, such as 0123456 78(or 64 Hexadecimal digits leading by 0x, such as "0x321253abcde..."). z If you choose VLAN ID as QCE Type, you have to type the ID number for it and specify traffic class from Low, Normal, Medium and High. z If you choose TCP/UDP Port as[...]

Vigor2130 Series User’s Guide 63 z If you choose ToS as QCE Type, you have to specify priority class from Low, Normal, Medium and High. z If you choose Tag Priority as QCE Type, you have to specify priority class from Low, Normal, Medium and High. E E d d i i t t i i n n g g a a Q Q C C E E Click to modify the settings of an existing QCE on this [...]

Vigor2130 Series User’s Guide 64 D D e e l l e e t t i i n n g g a a Q Q C C E E To delete a QCE in the list, simply click of that one. It will be removed immediately. 3 3 . . 4 4 . . 5 5 P P o o r r t t s s P P r r i i o o r r i i t t y y This page allows you to configure QoS settings for each port. The classification is controlled by a QCL (Qua[...]

Vigor2130 Series User’s Guide 65 Queue Weighted Use the drop down list to c hoose 1, 2, 4, or 8 as the queue weighted number. 3 3 . . 4 4 . . 6 6 Q Q o o S S S S t t a a t t i i s s t t i i c c s s This page displays statistics for QoS se tting. Click WAN/LAN link to check detailed information for each interface. Click WAN/LAN link to check detai[...]

Vigor2130 Series User’s Guide 66 Rx Broadcast Display the counting number of the received broadcast packet. Rx Pause Display the counting number of the received pause packet. RX 64 Bytes Display the number of 64-byte frames in good and bad packets received. RX 65-127 Bytes Display the number of 65 ~ 127-byte frames in good and bad packets receive[...]

Vigor2130 Series User’s Guide 67 Tx 64 Bytes Display the number of 64-byte fra mes in good and bad packets transmitted. Tx 65-127 Bytes Display the number of 65 ~ 127-byte frames in good and bad packets transmitted. Tx 128-255 Bytes Display the number of 128 ~ 255-byte frames in good and bad packets transmitted. Tx 256-511 Bytes Display the numbe[...]

Vigor2130 Series User’s Guide 68 www.dtdns.com, www.changeip.com, www.dynamic- nameserver.com. You should visit their websites to register your own domain nam e for the router. Enable Dynamic DNS Check this box to enable the current account. DynDNS Service Select the service provider for the DDNS account. Hostname Type in one domain name that you[...]

Vigor2130 Series User’s Guide 69 Enable Check to enable the schedule. Start Date Specify the starting date of the schedule. Start Time Specify the starting time of the schedule. Action Specify which action should be applied during the pe riod of the schedule. WAN UP/DOWN – WAN connection will be activated / inactivated based on the time schedul[...]

Vigor2130 Series User’s Guide 70 3 3 . . 5 5 . . 3 3 I I G G M M P P S S n n o o o o p p i i n n g g IGMP snooping means multicast traffic will be forwarded to ports that have members of that group. If you disable IGMP snooping, the system will make multicast traffic treated in the same manner as broadcast traffic. Snooping Enabled Check the box [...]

Vigor2130 Series User’s Guide 71 3 3 . . 5 5 . . 5 5 U U P P n n P P C C o o n n f f i i g g u u r r a a t t i i o o n n The UPnP (Universal Plug and Play) protocol is supported to bring to network connected devices the ease of installation and configurati on which is already available for directly connected PC peripherals with the existing Windo[...]

Vigor2130 Series User’s Guide 72 The reminder as regards concern about Firewall and UPnP Can't work with Firewall Software Enabling firewall applications on your P C may cause the UPnP function not working properly. This is because these applicati ons will block the accessing ability of some network ports. Security Considerations Activating [...]

Vigor2130 Series User’s Guide 73 Wake by Two types provide for you to wake up the binded IP . If you choose Wake by MAC Address, you have to type the correct MAC address of the host in MAC Address boxes. If you choose Wake by IP Address, you have to choose the correct IP address. IP Address The IP addresses that have been configured in LAN>>[...]

Vigor2130 Series User’s Guide 74 Note : * The actual data throughput will vary according to the network conditions and environmental factors, including volum e of network traffic, network overhead and building materials. In an Infrastructure Mode of wireless network, Vigor wireless router plays a role as an Access Point (AP) connecting to lots of[...]

Vigor2130 Series User’s Guide 75 3 3 . . 6 6 . . 2 2 G G e e n n e e r r a a l l S S e e t t u u p p By clicking the General Setup , a new web page will appear so that you could configure the SSIDs and the wireless channel. Please refer to the following figure for more information. Enable Wireless LAN Check the box to enable the wireless function[...]

Vigor2130 Series User’s Guide 76 Tx Power Set the power percentage for transmission signal of access point. The greater the value is, the higher intensity of the signal will be. Enable Green AP Such function is used to reduce the power consumption (Green AP) for the access point. When there is no station connected, the power consumption of access[...]

Vigor2130 Series User’s Guide 77 Key1-Key4 Four keys can be entered here, but only one key can be selected at a time. The format of WEP Key is restricted to 5 ASCII characters or 10 hexadecimal values in 64-bit encryption level, or restricted to 13 ASCII characters or 26 hexadecimal values in 128-bit encryption level. The allowed content is the A[...]

Vigor2130 Series User’s Guide 78 Type The WPA encrypts each fra me transmitted from the radio using the key, which either PSK (Pre-Shared Key) entered manually in this field below or automatically negotiated via 802.1x authentication. Select WPA, WPA2 or Auto as WPA mode. WPA Algorithm Choose the WPA algorithm, TKIP, AES or Auto. Server IP Addres[...]

Vigor2130 Series User’s Guide 79 router will blink fast when WPS is in progress. It will return to normal condition after two minutes. (You need to setup WPS within two minutes) Configure via Client PinCode Type the PIN code specified in wireless client you wish to connect, and click Start PIN button. The WLAN LED on the router will blink fast wh[...]

Vigor2130 Series User’s Guide 80 If you want to use PIN code, you have to know the PIN code specified in wireless client. Then provide the PIN code of the wireless clie nt you wish to connect to the vigor router. 3 3 . . 6 6 . . 3 3 A A c c c c e e s s s s C C o o n n t t r r o o l l For additional security of wireless access, the Access Control [...]

Vigor2130 Series User’s Guide 81 OK Click it to save the configuration. 3 3 . . 6 6 . . 4 4 S S t t a a t t i i o o n n L L i i s s t t Station List provides the knowledge of connecting wire less clients now along with its status code. Index Display the number of the connecting client. IP Address Display the WAN IP address for the connecting clie[...]

Vigor2130 Series User’s Guide 82 3 3 . . 6 6 . . 5 5 A A c c c c e e s s s s P P o o i i n n t t D D i i s s c c o o v v e e r r y y Vigor router can scan all regulatory channels and find working APs in the neighborhood. Based on the scanning result, users will know which channel is clean for usage. Note: During the scanning process (about 5 seco[...]

Vigor2130 Series User’s Guide 83 Enable FTP Check this box to enable FTP connection. Enable Disk Sharing Check this box to enable Sam ba file sharing. Workgroup Name Type the name for FTP users for accessing into FTP server (USB diskette). Be aware that users cannot access int o USB diskette in anonymity. Later, you can open FTP client software a[...]

Vigor2130 Series User’s Guide 84 Note: When write protec t status for the USB diskette is ON , you cannot type any new folder name in this field. Only “/” can be used in such case. Access Rule Select the access right for the USB diskette. When you finish the settings, simply click OK to save the configuration. 3 3 . . 7 7 . . 3 3 D D i i s s [...]

Vigor2130 Series User’s Guide 85 Share Name Type a name to be used as shar ed folder name in Samba service. The name must not contain spaces or special characters. Comment Type the brief description for the disk sharing. The w ords here will be seen in Network Nei ghborhood on Windows client computers Volume Select the proper volume for the conne[...]

Vigor2130 Series User’s Guide 86 3 3 . . 8 8 I I P P v v 6 6 3 3 . . 8 8 . . 1 1 I I P P v v 6 6 W W A A N N S S e e t t u u p p This page defines the IPv6 connection typ es for WAN interface. Possible types contain Link-Local only, Static IPv6, DHCPv6 and TSPC . Each type requires different param eter settings. L L i i n n k k - - L L o o c c a [...]

Vigor2130 Series User’s Guide 87 IPv6 Address The least significant 64 bits are usually chosen as the interface hardware address constructed in modified EUI-64 format. Prefix Length Display the fixed value (64) for prefix length. S S t t a a t t i i c c I I P P v v 6 6 This type allows you to setup static IPv6 address for WAN. IPv6 Address Type y[...]

Vigor2130 Series User’s Guide 88 D D H H C C P P v v 6 6 C C l l i i e e n n t t ( ( I I A A _ _ N N A A ) ) DHCPv6 client mode would use IA_NA option of DHCPv6 protocol to obtain IPv6 address from server. Primary DNS Server Type primary DNS Server address here. Secondary DNS Server Type secondary DNS Server address here D D H H C C P P v v 6 6 C[...]

Vigor2130 Series User’s Guide 89 Username Type the name obtained from the broker. “vigor2130” is a default username applied from http://go6.net/4105/register.asp . It is suggested for you to apply another username and password. Password Type the password assigned with the user name. Confirm Password Type the password again to make the confirm[...]

Vigor2130 Series User’s Guide 90 Prefixlen Type the required prefix length for the client network. If_prefix Display LAN interface name. The name of the OS interface that will be conf i gured with the first 64 of the received prefix from the broker and the router advertisement daemon is star ted to advertise that prefix on the if_prefix interface[...]

Vigor2130 Series User’s Guide 91 RADVD - The router advertisement daemon (radvd) sends Router Advertisement messages, specified by RFC 2461, to a local Ethernet LAN peri odically and when requested by a node sending a Router Solicitation message. These messages are required for IPv6 stateless autoconfiguration. Advertisement Lifetime - The lifeti[...]

Vigor2130 Series User’s Guide 92 A A d d d d i i n n g g a a N N e e w w R R u u l l e e Click Add New Rule to configure a new rule for IPv6 Firewall. Note: You can set up to 20 sets of IPv6 rules. Name Type a name for the rule. Protocol Specify a protocol for this rule. Source IP Type Deter mine the IP type as the source. Source IP Type the IP a[...]

Vigor2130 Series User’s Guide 93 Destination Subnet Type the subnet mask here if you choose Subnet as Destination IP Type . Source Start Port Type a value as the source start port. Such value will be available only TCP/UDP is selected as the protocol. Source End Port (optional) Type a value as the source end port. Such value will be available onl[...]

Vigor2130 Series User’s Guide 94 Hoplimit Display t he number of network segments on which the packet is allowed to travel before discarded. Auto-refresh Check this box to enable an automatic refresh of the page at regular intervals. 3 3 . . 8 8 . . 5 5 I I P P v v 6 6 N N e e i i g g h h b b o o u u r r IPv6 uses neighbor discovery protocol to f[...]

Vigor2130 Series User’s Guide 95 When TSPC configuration has been done, the router will start to connect. The connecting page will be shown as below: When the router detects all the information, the screen will be shown as follows. One set of TSPC prefix and prefix length will be obtained after the connection between TSPC and Tunnel broker built.[...]

Vigor2130 Series User’s Guide 96 When the router connects to the tunnel broke r, the router will use RADVD to transmit the prefix to the PC on LAN. Next, the PC will gene rate one set of IPv6 public IP (see the figure below). Users can use such IP for connecting to IPv6 network. When your PC obtains the IPv6 address, please connect to http://www.[...]

Vigor2130 Series User’s Guide 97 3 3 . . 9 9 U U s s e e r r 3 3 . . 9 9 . . 1 1 U U s s e e r r C C o o n n f f i i g g u u r r a a t t i i o o n n This page allows you to set user’s setti ng that allowed to use PPTP, FTP, IPSEC/L2TP connection. A A d d d d i i n n g g a a N N e e w w U U s s e e r r Click Add a New User to open the following [...]

Vigor2130 Series User’s Guide 98 E E d d i i t t i i n n g g / / D D e e l l e e t t i i n n g g U U s s e e r r S S e e t t t t i i n n g g s s To edit a user, click the name link under Userna me to open the following page. M odify the settings except Username and then click OK to save and exit it. If you want to remove such user settings, simpl[...]

Vigor2130 Series User’s Guide 99 Model Name Display the model name of the router. Firmware Version Display the firmware version of the router. Build Date/Time Display the date and time of the current firmware build. System Date Display current time and date for the system server. System Uptime Display the connection time for the system server. Sy[...]

Vigor2130 Series User’s Guide 100 MAC Address Display the MAC address of the wireless LAN. Device Type Display the device type used for wireless LAN. SSID Display the SSID of the router. Channel Display the channel that wireless LAN used. Manufacturer Display the manufacturer of the disk. Model Display the model of the disk. Size Display the stor[...]

Vigor2130 Series User’s Guide 101 please set URL as the following: http://{IP address of VigorACS}:8080/ACSServer/services/UnAuthACSServ let Username/Password - Type userna me and password for ACS Server for authentication. For example, if you want to use such CPE with VigorACS, you can type as the following: Username : acs Password : password CP[...]

Vigor2130 Series User’s Guide 102 3 3 . . 1 1 0 0 . . 4 4 C C o o n n f f i i g g u u r r a a t t i i o o n n B B a a c c k k u u p p B B a a c c k k u u p p t t h h e e C C o o n n f f i i g g u u r r a a t t i i o o n n Follow the steps below to backup your configuration. 1. Go to System Maintenance >> Configuration Backup . The following[...]

Vigor2130 Series User’s Guide 103 4. Click Save button, the configuration will download a utomatically to your computer as a file named config.cfg . The above example is using W indows platform for demonstrating exam ples. The Mac or Linux platform will appear dif ferent windows, but the backup function is still available. Note: Backup for Certif[...]

Vigor2130 Series User’s Guide 104 3 3 . . 1 1 0 0 . . 5 5 S S y y s s l l o o g g / / M M a a i i l l A A l l e e r r t t SysLog function is provided for users to monitor router. There is no bother to directly get into the Web Configurator of the router or borrow debug equipm ents. Enable (Syslog Access…) Check the box to activate function of s[...]

Vigor2130 Series User’s Guide 105 Click OK to save these settings. For viewing the Syslog, please do the following: 1. Just set your monitor PC’s IP address in the field of Server IP Address 2. Install the Router Tools in the Utility within provided CD. After installation, click on the Router Tools>>Syslog from program menu. 3. From the S[...]

Vigor2130 Series User’s Guide 106 3 3 . . 1 1 0 0 . . 6 6 T T i i m m e e a a n n d d D D a a t t e e It allows you to specify where the time of the router should be inquired from. Current System Time Click Inquire Time to get the current time. Time Zone Select the ti me zone where the router is located. Add NTP server Click the button to add a n[...]

Vigor2130 Series User’s Guide 107 3 3 . . 1 1 0 0 . . 7 7 M M a a n n a a g g e e m m e e n n t t This page allows you to manage the setti ngs for access control, access list, port setup, and SMP setup. For example, as to management access control, the port number is used to send/receive SIP message for building a session. The default value is 50[...]

Vigor2130 Series User’s Guide 108 3 3 . . 1 1 0 0 . . 8 8 R R e e b b o o o o t t S S y y s s t t e e m m The Web Configurator may be used to restart your router for using current configuration. Click Reboot System from System Maintenance to open the following page. Click OK . The router will take 5 seconds to reboot the system. Note: When the sy[...]

Vigor2130 Series User’s Guide 109 4 A A d d m m i i n n M M o o d d e e O O p p e e r r a a t t i i o o n n This chapter will guide users to execute adva nced (full) configuration thr ough admin mode operation. 1. Open a web browser on your PC and type http://192. 168.1.1. The window will ask for typing username and password. 2. Please type “ a[...]

Vigor2130 Series User’s Guide 110 W W h h a a t t a a r r e e P P u u b b l l i i c c I I P P A A d d d d r r e e s s s s a a n n d d P P r r i i v v a a t t e e I I P P A A d d d d r r e e s s s s As the router plays a role to manage and further protect its LAN, it interconnects groups of host PCs. Each of them has a private IP address assigned [...]

Vigor2130 Series User’s Guide 111 4 4 . . 1 1 . . 1 1 I I n n t t e e r r n n e e t t A A c c c c e e s s s s This page allows you to set WAN configura tion with different modes. Use the Connection Type drop down list to choose one of the WAN modes. The corresponding page will be displayed. S S t t a a t t i i c c For static IP mode, you usually [...]

Vigor2130 Series User’s Guide 112 IP Address Type the IP address. Subnet Mask Type the subnet mask. Gateway IP Address Type the gateway IP address. Primary DNS Server Y ou must specify a DNS server IP address here because your ISP should provide you with usually more than one DNS Server . If your ISP does not provide it, the router will automatic[...]

Vigor2130 Series User’s Guide 113 D D H H C C P P DHCP allows a user to obtain an IP address automatically from a DHCP server on the Internet. If you choose DHCP mode, the DHCP server of your ISP will assign a dynamic IP address for your router automatically. It is not necessary for you to assign any setting, Router Name Type in a name for the ro[...]

Vigor2130 Series User’s Guide 114 P P P P P P o o E E To choose PPPoE as the accessing protocol of the internet, please select PPPoE from the Internet Access menu. The following web page will be shown. Username Type in the username provided by ISP in this field. Password Type in the password provided by ISP in this field. Redial Policy If you wan[...]

Vigor2130 Series User’s Guide 115 After finishing all the settings here, please click OK to activate them. P P P P T T P P / / L L 2 2 T T P P To use PPTP/L2TP as the accessing protocol of the internet, please choose PPTP/L2TP from Connection Type drop down menu. The following web page will be shown. Username Type in the username provided by ISP [...]

Vigor2130 Series User’s Guide 116 Redial Policy If you want to connect to Internet all the time, you can choose Always On . Otherwise, choose Connect on Demand and Idle Time Out Set the timeout for breaking down the Internet after passing through the time without any action. When you choose Connect on Demand, you have to type value here. MTU Size[...]

Vigor2130 Series User’s Guide 117 Modem Dial String Such value is used to dial through USB mode. Please use the default value. If you have any question, please contact to your ISP. PPP Username Type the PPP username (optional). PPP Password Type the PPP password (optional). Clone MAC Address It is available when the box of Enable is checked. Clic[...]

Vigor2130 Series User’s Guide 118 Current Tx: indicates whether pause frames on the port are transmitted. Maximum Frame This module offers 1518~9600 (B ytes) length to make the long packet for data transmission. Excessive Collision Mode There are two modes for yo u to choose when excessive collision happened in half-duplex condition. Discard - It[...]

Vigor2130 Series User’s Guide 119 SIM PIN code Type PIN code of the SIM card that will be used to access Internet. Modem Initial String1/2 Such value is used to initia lize USB modem. Please use the default value. If you have any question, please contact to your ISP. APN Name APN means Access Point Name which is provided and required by some ISPs[...]

Vigor2130 Series User’s Guide 120 4 4 . . 2 2 L L A A N N Local Area Network (LAN) is a group of subnets regulated and ruled by router . The design of network structure is related to what type of public IP addresses coming from your ISP . B B a a s s i i c c s s o o f f L L A A N N The most generic function of V igor router is NA T . It creates a[...]

Vigor2130 Series User’s Guide 121 W W h h a a t t i i s s R R o o u u t t i i n n g g I I n n f f o o r r m m a a t t i i o o n n P P r r o o t t o o c c o o l l ( ( R R I I P P ) ) V igor router will exchange routing informati on with neighboring routers using the RIP to accomplish IP routing. This allows users to cha nge the information of the [...]

Vigor2130 Series User’s Guide 122 4 4 . . 2 2 . . 1 1 G G e e n n e e r r a a l l S S e e t t u u p p This page provides you the general settings for LAN. Click LAN to open the LAN settings page and choose General Setup . IP Address T ype in private IP address for connecting to a local private network (Default: 192.168.1.1). Subnet Mask T y pe in[...]

Vigor2130 Series User’s Guide 123 Secondary IP Address Y ou can specify secondary DNS server IP address here because your ISP often provides you more than one DNS Server . If your ISP does not provide it, the router will autom atically apply default secondary DNS Server IP address: 194.98.0.1 to this field. The default DNS Server IP address can b[...]

Vigor2130 Series User’s Guide 124 Auto . Flow Control If flow control is enabled by checking Configured box, bot h parties can send PAUSE frame to the transmitting device(s) if the receiving port is too busy to handle. If not, there will be no flow control in the port. It drops the pac ket if too much to handle. Current Rx: indicates whether paus[...]

Vigor2130 Series User’s Guide 125 4 4 . . 2 2 . . 3 3 M M A A C C A A d d d d r r e e s s s s T T a a b b l l e e This page allows you to set timeouts for en tries in dynamic MAC Table and configure the static MAC table here. Disable Automatic Aging Stop the MAC table aging timer, the learned MAC address will not age out automatically. The defaul[...]

Vigor2130 Series User’s Guide 126 4 4 . . 2 2 . . 4 4 V V L L A A N N Virtual LAN function provides you a very convenient way to manage hosts by g rouping them based on the physical port. You can also mana ge the in/out rate of each port. Go to LAN page and select VLAN . The following page will appear. VLAN function is enabled in default. Add New[...]

Vigor2130 Series User’s Guide 127 3. T o remove VLAN, click the Delete button fo r the one you want to remove and click OK to save the results. 4 4 . . 2 2 . . 5 5 M M o o n n i i t t o o r r P P o o r r t t It is used to monitor the traffic of the networ k. For example, we assume that LAN1 and LAN2 are Monitor Port and Monitor ingress Port resp [...]

Vigor2130 Series User’s Guide 128 Destination Address Display the destination address of the static route. Status Display the status of the static route. Add Click it to add a new static route. A A d d d d S S t t a a t t i i c c R R o o u u t t e e s s t t o o P P r r i i v v a a t t e e a a n n d d P P u u b b l l i i c c N N e e t t w w o o r [...]

Vigor2130 Series User’s Guide 129 2. Return to St a t i c R o u t e page. Click Add again to add another static route as show below , which regulates all packets destined to 21 1.100.88.0 will be forwarded to 19 2.168.1.3. 3. V erify current routing table. 4 4 . . 2 2 . . 7 7 B B i i n n d d I I P P t t o o M M A A C C This function is used to bi[...]

Vigor2130 Series User’s Guide 130 Enable Click this radio button to invoke this function. However, IP/MAC which is not listed in IP Bind List also can connect to Internet. Disable Click this radio button to disable this function. All the settings on this page will be invalid. Strict Bind Click this radio button to block the connection of the I P/[...]

Vigor2130 Series User’s Guide 131 z Enhance security of the internal network by obscuring the IP address. Ther e are many attacks aiming victims based on the IP address. Since the attacker cannot be aware of any private IP addresses, the NAT function can protect the internal network. On NAT page, you will see the private IP address defined in RFC[...]

Vigor2130 Series User’s Guide 132 Name Specify the name for the defined network service. Protocol Specify the transport layer protocol. It could be TCP , UDP and TCP+UDP . Start Port Specify the starting port number of the service offered by the local host. End Port (optional) Specify the ending port number of the service offered by the local hos[...]

Vigor2130 Series User’s Guide 133 4 4 . . 3 3 . . 3 3 D D M M Z Z H H o o s s t t As mentioned above, Port Redirection can redirect incoming TCP/UDP or othe r traffic on particular ports to the specific private IP address/port of host in the LAN. However, other IP protocols, for example Protocols 50 (ESP) and 51 (A H), do not travel on a fixed po[...]

Vigor2130 Series User’s Guide 134 4 4 . . 4 4 F F i i r r e e w w a a l l l l B B a a s s i i c c s s f f o o r r F F i i r r e e w w a a l l l l While the broadband users demand more bandwidth f or multimedia, interactive applications, or distance learning, security has been always the most concerned. The firewall of the Vigor router helps to pr[...]

Vigor2130 Series User’s Guide 135 second). The configuration indicates the permitted packet rate for unicast, multicast, or broadcast traffic across the switch. 4 4 . . 4 4 . . 2 2 P P o o r r t t s s C C o o n n f f i i g g u u r r a a t t i i o o n n This page is used to configure the ACL (Access Control List) parameters for each port. These pa[...]

Vigor2130 Series User’s Guide 136 Clear Click this button to clear the num ber of the counter on this page. R R a a t t e e L L i i m m i i t t e e r r I I D D Configure the rate limiter for the ACL (Access Control List) of the router. Please click Rate Limiter ID link to access into the following page. Rate Limiter ID Rate li miter ID will be ap[...]

Vigor2130 Series User’s Guide 137 4 4 . . 4 4 . . 3 3 A A c c c c e e s s s s C C o o n n t t r r o o l l L L i i s s t t This page can define which kind of packet can access the router. The packet can be defined with input port, Frame type, Rate, MAC t ype, VLAN ID, tag and etc.. For IPv4, we can also define the protocol type, source IP and dest[...]

Vigor2130 Series User’s Guide 138 list will be applied to if matching with the rule defined in this page. Rate Limiter - Select a rate limiter to apply to this port. Available settings include Disabled , and 1 to 10. The default value is Disabled . Click the Rate Limiter link to configure different rates for each ID. D D e e t t a a i i l l e e d[...]

Vigor2130 Series User’s Guide 139 ARP/RARP Choose the ARP/RARP that you want to filter. Request/Reply Choose the request or replay that you want to filter. Sender IP Filter Specify the sender IP filter for this ACE. Choose Any to filter all of the packets. Choose Host to filter the packets from the host with the address typed in Sender IP Address[...]

Vigor2130 Series User’s Guide 140 Target IP Address Type the Target IP Address here. This option is available when you choose Host or Network as Target IP Filter. Target IP Mask Type the Target IP Mask here. This option is available only when you choose Network as Target IP Filter. ARP SMAC Match Specify whether frames/packets can me et the actio[...]

Vigor2130 Series User’s Guide 141 0 : ARP/RARP frames where the hardware address sp ace is equal to Ethernet (1) must not match this entry. 1 : ARP/RARP frames where the hardware address sp ace is equal to Ethernet (1) must match this entry. Any: Any value is allowed. Ethernet Specify whether frames can hit the action according to their ARP/RARP [...]

Vigor2130 Series User’s Guide 142 Dest IP Filter Specify the destination IP filter for this ACE. Any: No destination IP filter is specified. Host: Destination IP filter is set to Host. Specify the destination IP address in the Dest IP Address field that appears. Network: Destination IP filter is set to Network. Specify the destination IP address [...]

Vigor2130 Series User’s Guide 143 Source IP Specify the source IP filter for this ACE. Any: No source IP filter is specified. Host : Source IP filter is set to Host. Specify the source IP address in the Source IP Address field that appears. Network: Source IP filter is set to Network. Specify the source IP address and source IP mask in the Source[...]

Vigor2130 Series User’s Guide 144 Specific: If you want to filter a specific UDP source filter with this ACE, you can enter a specific UDP source value. A field for entering a UDP source value appears. Range: If you want to filter a specific UDP source range filter with this ACE, you can enter a specific UDP source range value. A field for enteri[...]

Vigor2130 Series User’s Guide 145 z Choose IPv4 as the Frame Type. You will see IP Parameters on the bottom of the page. If you choose TCP as IP Protocol Filter , you will get the page as the following: Source IP Specify the source IP filter for this ACE. Any: No source IP filter is specified. Host : Source IP filter is set to Host. Specify the s[...]

Vigor2130 Series User’s Guide 146 Source Port Filter Specify the TCP port source filter for this ACE. Any: No TCP source filter is specified. Specific: If you want to filter a specific TCP source filter with this ACE, you can enter a specific TCP source value. A field for entering a TCP source value appears. Range: If you want to filter a specifi[...]

Vigor2130 Series User’s Guide 147 TCP SYN Specify the TCP "Synchronize sequence num bers" (SYN) value for this ACE. 0: TCP frames where the SYN field is set must not be able to match this entry. 1: TCP frames where the SYN field is set must be able to match this entry. Any: Any value is allowed. TCP RST Specify the TCP RST value for thi[...]

Vigor2130 Series User’s Guide 148 1: TCP frames where the URG field is set must be able to match this entry. Any: Any value is allowed. z Choose IPv4 as the Frame Type. You will see IP Parameters on the bottom of the page. If you choose Other as IP Protocol Filter , you will get the page as the following: IP Protocol Value When "Other" [...]

Vigor2130 Series User’s Guide 149 destination IP address and destin ation IP mask fields that appear. Dest IP Address Type the Dest IP Address here . This option is available when you choose Host or Network as destination IP filter. Dest IP Mask Type the Dest IP Mask here. This option is available only when you choose Network as destination IP fi[...]

Vigor2130 Series User’s Guide 150 Disable Click this button to close the function of limit session. Default Sessions Limit Defines the default session number used for each computer in LAN. Limitation List Displays a list of specific limitations that you set on this web page. Start IP Defines the st art LAN IP address for limit session. End IP Def[...]

Vigor2130 Series User’s Guide 151 To activate the function of limit bandwidth, simply click Enable and set the default or user-defined upstream and downstream limit. Disable Click this button to close the function of lim it bandwidth. Enable Click this button to activate the function of limit bandwidth. Smart Bandwidth Limit Click this radio butt[...]

Vigor2130 Series User’s Guide 152 4 4 . . 5 5 . . 3 3 P P o o r r t t R R a a t t e e C C o o n n t t r r o o l l A policer can limit the bandwidth of received frames. It is located in front of the ingress queue. And a shaper can limit the bandwidth of tran smitted frames. It is located after the ingress queues. This page allows you to configure [...]

Vigor2130 Series User’s Guide 153 z Scheduling: Based on classification of service level to assign packets to queues and associated service types The basic QoS implementation in Vigor routers is to classify and schedule packets based on the service type information in the IP header. Fo r instance, to ensure the connection with the headquarter, a [...]

Vigor2130 Series User’s Guide 154 QCE Type Display the type of that QCE (QoS Control Entries). Type Value Display the value specified for the QCE. Traffic Class Display the class of the data transmission for the QCE. QoS Control List allows users to set up to five groups of QCL. Each QCL group c an contain 12 QCE settings. A A d d d d i i n n g g[...]

Vigor2130 Series User’s Guide 155 Ethernet Type Value Either 8~63 ASCII characters, such as 0123456 78(or 64 Hexadecimal digits leading by 0x, such as "0x321253abcde..."). z If you choose VLAN ID as QCE Type, you have to type the ID number for it and specify traffic class from Low, Normal, Medium and High. z If you choose TCP/UDP Port a[...]

Vigor2130 Series User’s Guide 156 z If you choose ToS as QCE Type, you have to specify priority class from Low, Normal, Medium and High. z If you choose Tag Priority as QCE Type, you have to specify priority class from Low, Normal, Medium and High. E E d d i i t t i i n n g g a a Q Q C C E E Click to modify the settings of an existing QCE on this[...]

Vigor2130 Series User’s Guide 157 D D e e l l e e t t i i n n g g a a Q Q C C E E To delete a QCE in the list, simply click of that one. It will be removed immediately. 4 4 . . 5 5 . . 5 5 P P o o r r t t s s P P r r i i o o r r i i t t y y This page allows you to configure QoS settings for each port. The classification is controlled by a QCL (Qu[...]

Vigor2130 Series User’s Guide 158 Queue Weighted Use the drop down list to c hoose 1, 2, 4, or 8 as the queue weighted number. 4 4 . . 5 5 . . 6 6 Q Q o o S S S S t t a a t t i i s s t t i i c c s s This page displays statistics for QoS se tting. Click WAN/LAN link to check detailed information for each interface. Click WAN/LAN link to check deta[...]

Vigor2130 Series User’s Guide 159 Rx Octets Display the total received bytes. Rx Unicast Display the counting number of the received unicast packet. Rx Broadcast Display the counting number of the received broadcast packet. Rx Pause Display the counting number of the received pause packet. RX 64 Bytes Display the number of 64-byte frames in good [...]

Vigor2130 Series User’s Guide 160 Tx Pause Show the counting number of the transmitted pause packet. Tx 64 Bytes Display the number of 64-byte fra mes in good and bad packets transmitted. Tx 65-127 Bytes Display the number of 65 ~ 127-byte frames in good and bad packets transmitted. Tx 128-255 Bytes Display the number of 128 ~ 255-byte frames in [...]

Vigor2130 Series User’s Guide 161 www.dtdns.com, www.changeip.com, www.dynamic- nameserver.com. You should visit their websites to register your own domain nam e for the router. Enable Dynamic DNS Check this box to enable the current account. DynDNS Service Select the service provider for the DDNS account. Hostname Type in one domain name that yo[...]

Vigor2130 Series User’s Guide 162 Enable Check to enable the schedule. Start Date Specify the starting date of the schedule. Start Time Specify the starting time of the schedule. Action Specify which action should be applied during the pe riod of the schedule. WAN UP/DOWN – WAN connection will be activated / inactivated based on the time schedu[...]

Vigor2130 Series User’s Guide 163 4 4 . . 6 6 . . 3 3 I I G G M M P P S S n n o o o o p p i i n n g g IGMP snooping means multicast traffic will be forwarded to ports that have members of that group. If you disable IGMP snooping, the system will make multicast traffic treated in the same manner as broadcast traffic. Snooping Enabled Check the box[...]

Vigor2130 Series User’s Guide 164 4 4 . . 6 6 . . 5 5 U U P P n n P P C C o o n n f f i i g g u u r r a a t t i i o o n n The UPnP (Universal Plug and Play) protocol is supported to bring to network connected devices the ease of installation and configurati on which is already available for directly connected PC peripherals with the existing Wind[...]

Vigor2130 Series User’s Guide 165 The UPnP facility on the router enables UPnP aware applications such as MSN Messenger to discover what are behind a NA T router . The application will also learn the external IP address and configure port mappings on the rout er . Subse quently , such a facility forwards packets fro m the external ports of the ro[...]

Vigor2130 Series User’s Guide 166 4 4 . . 6 6 . . 6 6 W W a a k k e e O O n n L L A A N N A PC client on LAN can be woken up by the router it connects. When a user wants to wake up a specified PC through the router, he/she must type correct MAC address of the specified PC on this web page of Wake On LAN of this router. In addition, such PC must h[...]

Vigor2130 Series User’s Guide 167 4 4 . . 7 7 . . 1 1 R R e e m m o o t t e e A A c c c c e e s s s s C C o o n n t t r r o o l l Enable the necessary VPN service as you need. If you intend to run a VPN server inside your LAN, you should enable IPSec VPN Pass-through and specify an IP address to allow VPN tunnel pass through. Enable IPSec VPN Ser[...]

Vigor2130 Series User’s Guide 168 4 4 . . 7 7 . . 2 2 P P P P T T P P R R e e m m o o t t e e D D i i a a l l - - i i n n You can manage remote access by maintaining a table of remote user profile, so that users can be authenticated to dial-in via VPN connection. The router provides access accounts for dial-in users. A A d d d d i i n n g g a a N[...]

Vigor2130 Series User’s Guide 169 When you finish the settings, simply click OK to save the configuration. The new user will be created and displayed on the page. E E d d i i t t i i n n g g / / D D e e l l e e t t i i n n g g U U s s e e r r S S e e t t t t i i n n g g s s To edit a user, click the name link under Userna me to open the following[...]

Vigor2130 Series User’s Guide 170 IPSec-related VPN connections such as L2TP over IPSec and IPSec tunnel. Disabled – Ignore the configurations set in this page. Dynamic VPN (IPSec) – Traffic between this subnet and the client will travel through the VPN tunnel. If you choose this type, please specify the IP address and subnet mask for local n[...]

Vigor2130 Series User’s Guide 171 mutual examination of the secure tunnel establishment. 4 4 . . 7 7 . . 4 4 R R e e m m o o t t e e D D i i a a l l - - i i n n S S t t a a t t u u s s You can find the summary table of all dial-in user status. Client Display the name of the VPN IPSec/Mobile client. Identity Display the remote ID of the VPN client[...]

Vigor2130 Series User’s Guide 172 4 4 . . 7 7 . . 5 5 L L A A N N t t o o L L A A N N Here you can manage LAN-to-LAN connections by maintaining a table of connection profiles. You may set parameters including specified c onnection direction (dial-in or dial-out), connection peer ID, connection type (VPN connection - including P PTP, IPSec Tunnel)[...]

Vigor2130 Series User’s Guide 173 A A d d d d i i n n g g a a V V P P N N T T u u n n n n e e l l Click Add Tunnel to open the following page. Enabled Check here to activate this tunnel. Always On Check this box to make the WAN connection being activated always. Name Specify a name for this tunnel. Remote IP Enter the IP address of the remote hos[...]

Vigor2130 Series User’s Guide 174 Confirm Pre-Shared key Such field will be applicable when Pre-shared key is selected as the Type for the authenticati on. Input 1-63 characters as pre-shared key again to confirm it. Local Identity Local Identity is on behalf of the IP address while identity authenticating with remote VPN server. The length of th[...]

Vigor2130 Series User’s Guide 175 4 4 . . 8 8 W W i i r r e e l l e e s s s s L L A A N N This function is used for “n” models. 4 4 . . 8 8 . . 1 1 B B a a s s i i c c C C o o n n c c e e p p t t s s Over recent years, the market for wireless co mmunications has enjoyed tremendous growth. Wireless technology now reaches or is capable of reach[...]

Vigor2130 Series User’s Guide 176 WEP (Wired Equivalent Privacy) is a legacy method to encrypt each frame transmitted via radio using either a 64-bit or 128-bit ke y. Usually access point will preset a set of four keys and it will communicate with each station using only one out of the four keys. WPA (Wi-Fi Protected Access), the most domin ating[...]

Vigor2130 Series User’s Guide 177 SSID Broadcast Choose Show to make the SSID being seen by wireless clients. Choose Hide to prevent from wireless sniffing and make it harder for unauthorized clients or STAs to join your wireless LAN. SSID It means the identification of the wireless LAN. SSID can be any text numbers or various special characters.[...]

Vigor2130 Series User’s Guide 178 z None The encryption mechan ism is turned off. z WEP Accepts only WEP clients and the encrypti on key should be entered in WEP Key. Default Key All wireless devices must support the same WEP encryption bit size and have the same key . Key1-Key4 Four keys can be entered here, but only one key can be selected at a[...]

Vigor2130 Series User’s Guide 179 WP A Mode Select WP A, WP A2 or Auto as the type. WP A Algorithm Select TKIP , AES or auto as the algorithm for WP A. WP A Pre-Shar ed Key Either 8~63 ASCII characters, such as 012345678..(or 64 Hexadecimal digits leading by 0x, such as "0x321253abcde..."). z WPA-RADIUS The built-in RADIUS client featur[...]

Vigor2130 Series User’s Guide 180 WPA Algorithm Choose the WPA algorithm, TKIP, AES or Auto. Server IP Address Enter the IP address of RADIUS server. Destination Port The UDP port number that the RADIUS server is using. The default value is 1812, based on RFC 2138. Shared Secret The RADIUS server and client share a secret that is used to authenti[...]

Vigor2130 Series User’s Guide 181 Note: Such function is available for the wi reless station with WPS supported. There are two methods to do network conn ection through WPS between AP and Stations: pressing the Start PBC button or using PIN Code . On the side of Vigor 2130 series which served as an AP, press WPS button once on the front panel of [...]

Vigor2130 Series User’s Guide 182 4 4 . . 8 8 . . 3 3 A A c c c c e e s s s s C C o o n n t t r r o o l l For additional security of wireless access, the Access Control facility allows you to restrict the network access right by controlling the wire less LAN MAC address of client. Only the valid MAC address that has been configured can access the[...]

Vigor2130 Series User’s Guide 183 Index Display the number of the connecting client. IP Address Display the WAN IP address for the connecting client. MAC Address Display the MAC Address for the connecting client. Connected Time Display the connection time for the connecting client. Auto-refresh Check this box to force the system refreshing the ta[...]

Vigor2130 Series User’s Guide 184 4 4 . . 9 9 U U S S B B A A p p p p l l i i c c a a t t i i o o n n USB diskette can be regarded as an FTP server. By way of Vigor router, clients on LAN can access, write and read data stored in USB diskette. After setting the configuration in USB Application , you can type the IP address of the Vigor router and[...]

Vigor2130 Series User’s Guide 185 User Name It displays the username that user uses to login to the FTP server. Volume Select the proper volume for the connected USB diskette. Home Folder It determines the range for the client to access into. The user can enter a directory name in this field. Then, after clicking OK , the router will create the s[...]

Vigor2130 Series User’s Guide 186 Update Click this button to refresh the disk status. 4 4 . . 9 9 . . 4 4 D D i i s s k k S S h h a a r r e e s s This page can define the folder which will be shared while Samba File Sharing is enabled. To add a new entry for disk sharing, please click Add a New Entry to open the following page. Share Name Type a[...]

Vigor2130 Series User’s Guide 187 All Users Read-only - everyone has read-only access to the share disk. All Users Read-write - every one has read-write access to the share disk. Specific Users – Only specific user(s) c an access into the share disk. 4 4 . . 1 1 0 0 I I P P v v 6 6 4 4 . . 1 1 0 0 . . 1 1 I I P P v v 6 6 W W A A N N S S e e t t[...]

Vigor2130 Series User’s Guide 188 Link-Local address is used for communicating with neighbouring nodes on the sam e link. It is defined by the address prefix fe80::/10 . You don't need to setup Link-Local address manually for it is generated automatically according to your MAC Address. IPv6 Address The least significant 64 bits are usually c[...]

Vigor2130 Series User’s Guide 189 D D H H C C P P v v 6 6 C C l l i i e e n n t t ( ( I I A A _ _ N N A A ) ) DHCPv6 client mode would use IA_NA option of DHCPv6 protocol to obtain IPv6 address from server. Primary DNS Server Type primary DNS Server address here. Secondary DNS Server Type secondary DNS Server address here D D H H C C P P v v 6 6 [...]

Vigor2130 Series User’s Guide 190 Username Type the name obtained from the broker. “vigor2130” is a default username applied from http://go6.net/4105/register.asp . It is suggested for you to apply another username and password. Password Type the password assigned with the user name. Confirm Password Type the password again to make the confir[...]

Vigor2130 Series User’s Guide 191 Prefixlen Type the required prefix length for the client network. If_prefix Display LAN interface name. The name of the OS interface that will be conf i gured with the first 64 of the received prefix from the broker and the router advertisement daemon is star ted to advertise that prefix on the if_prefix interfac[...]

Vigor2130 Series User’s Guide 192 RADVD - The router advertisement daemon (radvd) sends Router Advertisement messages, specified by RFC 2461, to a local Ethernet LAN peri odically and when requested by a node sending a Router Solicitation message. These messages are required for IPv6 stateless autoconfiguration. Advertisement Lifetime - The lifet[...]

Vigor2130 Series User’s Guide 193 A A d d d d i i n n g g a a N N e e w w R R u u l l e e Click Add New Rule to configure a new rule for IPv6 Firewall. Note: You can set up to 20 sets of IPv6 rules. Name Type a name for the rule. Protocol Specify a protocol for this rule. Source IP Type Deter mine the IP type as the source. Source IP Type the IP [...]

Vigor2130 Series User’s Guide 194 Destination Subnet Type the subnet mask here if you choose Subnet as Destination IP Type . Source Start Port Type a value as the source start port. Such value will be available only TCP/UDP is selected as the protocol. Source End Port (optional) Type a value as the source end port. Such value will be available on[...]

Vigor2130 Series User’s Guide 195 5. Connect PC to http://www.ipv6.org/ with IPv6 IP address again. A message will appear from web page: Welcome to the IPv6 Information Page! You are using IPv4 from 114.37.132.2 19 4 4 . . 1 1 0 0 . . 4 4 I I P P v v 6 6 R R o o u u t t i i n n g g This page displays the routing table for the protocol of IPv6. De[...]

Vigor2130 Series User’s Guide 196 Advmss Display t he largest size (in bytes) of an unfragmented piece of a routing advertisement. Hoplimit Display t he number of network segments on which the packet is allowed to travel before discarded. Auto-refresh Check this box to enable an automatic refresh of the page at regular intervals. 4 4 . . 1 1 0 0 [...]

Vigor2130 Series User’s Guide 197 When TSPC configuration has been done, the router will start to connect. The connecting page will be shown as below: When the router detects all the information, the screen will be shown as follows. One set of TSPC prefix and prefix length will be obtained after the connection between TSPC and Tunnel broker built[...]

Vigor2130 Series User’s Guide 198 Tunnel Information Display interface name (used to send TSPC prefix), tunnel mode, local endpoint addresses, remote endpoi nt address, TSPC Prfix, TSPC Prefixlen (prefix length), tunnel broker and so on. Tunnel Status Disconnected - The remote client doesn't connect to the tunnel server. Connecting - The rem[...]

Vigor2130 Series User’s Guide 199 4 4 . . 1 1 1 1 U U s s e e r r 4 4 . . 1 1 1 1 . . 1 1 U U s s e e r r C C o o n n f f i i g g u u r r a a t t i i o o n n This page allows you to set user’s setti ng that allowed to use PPTP, FTP, IPSEC/L2TP connection. A A d d d d i i n n g g a a N N e e w w U U s s e e r r Click Add a New User to open the f[...]

Vigor2130 Series User’s Guide 200 When you finish the settings, simply click OK to save the configuration. The new user will be created and displayed on the page. E E d d i i t t i i n n g g / / D D e e l l e e t t i i n n g g U U s s e e r r S S e e t t t t i i n n g g s s To edit a user, click the name link under Userna me to open the following[...]

Vigor2130 Series User’s Guide 201 4 4 . . 1 1 2 2 S S y y s s t t e e m m M M a a i i n n t t e e n n a a n n c c e e For the system setup, there are several items that you have to know the way of configuration: Status, User Password, Configuration Backup, Syslog/Mail Alert, Time and Date, Management, Reboot System , and Firmware Upgrade. Below s[...]

Vigor2130 Series User’s Guide 202 CPU Usage Display the percentage of the CPU usage of your sy stem. Memory Usage Display the size of the memory usage and the percentage. LAN------- MAC Address Display the MAC address of the LAN Interface. IP Address Display the IP address of the LAN interface. IP Mask Display the subnet mask address of the LAN i[...]

Vigor2130 Series User’s Guide 203 ACS Settings Such data must be typed according to the ACS ( Auto Configuration Server) you wa nt to link. Please refer to VigorACS user’s manual for detailed information. URL - Type the URL for VigorACS server. If the connected CPE needs to be authenticated, please set URL as the following and type username and[...]

Vigor2130 Series User’s Guide 204 ACS server. Enable – The system will send inform message to ACS server periodically (with the time set in the box of interval time). The default setting is Enable . Please set interval time or schedule time for the router to send notification to CPE. Or click Disable to close the mechanism of notification. 4 4 [...]

Vigor2130 Series User’s Guide 205 When you click OK , the login window will appear. Please use the new password to access into the web configurator again. 4 4 . . 1 1 2 2 . . 5 5 C C o o n n f f i i g g u u r r a a t t i i o o n n B B a a c c k k u u p p B B a a c c k k u u p p t t h h e e C C o o n n f f i i g g u u r r a a t t i i o o n n Follo[...]

Vigor2130 Series User’s Guide 206 4. Click Save button, the configuration will download a utomatically to your computer as a file named config.cfg . The above example is using W indows platform for demonstrating exam ples. The Mac or Linux platform will appear dif ferent windows, but the backup function is still available. Note: Backup for Certif[...]

Vigor2130 Series User’s Guide 207 4 4 . . 1 1 2 2 . . 6 6 S S y y s s l l o o g g / / M M a a i i l l A A l l e e r r t t SysLog function is provided for users to monitor router. There is no bother to directly get into the Web Configurator of the router or borrow debug equipm ents. Enable (Syslog Access…) Check “ Enable ” to activate functi[...]

Vigor2130 Series User’s Guide 208 2. Install the Router Tools in the Utility within provided CD. After installation, click on the Router Tools>>Syslog from program menu. 3. From the Syslog screen, select the router you want to monitor. Be reminded that in Network Information , select the network adapter used to connect to the router. Otherw[...]

Vigor2130 Series User’s Guide 209 4 4 . . 1 1 2 2 . . 7 7 T T i i m m e e a a n n d d D D a a t t e e It allows you to specify where the time of the router should be inquired from. Current System Time Click Inquire Time to get the current time. Time Zone Select the ti me zone where the router is located. Add NTP server Click the button to add a n[...]

Vigor2130 Series User’s Guide 210 4 4 . . 1 1 2 2 . . 8 8 M M a a n n a a g g e e m m e e n n t t This page allows you to manage the setti ngs for access control, access list, port setup, and SMP setup. For example, as to management access control, the port number is used to send/receive SIP message for building a session. The default value is 50[...]

Vigor2130 Series User’s Guide 211 4 4 . . 1 1 2 2 . . 9 9 R R e e b b o o o o t t S S y y s s t t e e m m The Web Configurator may be used to restart your router for using current configuration. Click Reboot System from System Maintenance to open the following page. Click OK . The router will take 5 seconds to reboot the system. Note: When the sy[...]

Vigor2130 Series User’s Guide 212 4 4 . . 1 1 3 3 D D i i a a g g n n o o s s t t i i c c s s Diagnostic Tools provide a useful way to view or diagnose the status of your Vigor router. Below shows the menu items for Diagnostics. 4 4 . . 1 1 3 3 . . 1 1 P P i i n n g g Click Diagnostics and click Ping to open the web page . It is used to troublesh[...]

Vigor2130 Series User’s Guide 213 4 4 . . 1 1 3 3 . . 2 2 R R o o u u t t i i n n g g T T a a b b l l e e Click Diagnostics and click Routing Table to open t he web page. Destination Display the IP address for destination network or destination host. Gateway Display the gateway address or “*” if none set. Genmas k Display the netmask f or the[...]

Vigor2130 Series User’s Guide 214 4 4 . . 1 1 3 3 . . 3 3 S S y y s s t t e e m m L L o o g g Click Diagnostics and click System Log to open the web page. Time Display the time of the system log entry. Level Display the severity level of the system log entry. Type Display the type or subsystem of the system log entry. Message Display a short desc[...]

Vigor2130 Series User’s Guide 215 Packets Display the packet sizes for data transmission in receiving and sending. Bytes Display the number of received and transmitted bytes per port. Errors Display the number of the error occurred in data receiving and data sending. Drops Display the number of the data lost in receiving and sending. Filtered Dis[...]

Vigor2130 Series User’s Guide 216 Rx Broadcast Display the counting number of the received broadcast packet. Rx Pause Display the counting number of the received pause packet. RX 64 Bytes Display the number of 64-byte frames in good and bad packets received. RX 65-127 Bytes Display the number of 65 ~ 127-byte frames in good and bad packets receiv[...]

Vigor2130 Series User’s Guide 217 Tx 64 Bytes Display the number of 64-byte frames in good and ba d packets transmitted. Tx 65-127 Bytes Display the num ber of 65 ~ 127-byte frames in good and bad packets transmitted. Tx 128-255 Bytes Display the number of 128 ~ 255-byte fram es in good and bad packets transmitted. Tx 256-511 Bytes Display the nu[...]

Vigor2130 Series User’s Guide 218 Type Indicate whether the entry is a static or dynamic entry. VLAN Display the VLAN ID of that entry. MAC Address Display the MAC address of that entry. Port Members Display the port of that entry. Auto-refresh Check it to enable auto-refresh function. Refresh Click it to reload the page. Clear Click it to clear [...]

Vigor2130 Series User’s Guide 219 4 4 . . 1 1 3 3 . . 7 7 D D H H C C P P T T a a b b l l e e The facility provides information on IP address as signments. This information is helpful in diagnosing network problems, such as IP address conflicts, etc. Click Diagnostics and click DHCP Table to open the web page. Computer Name It displays the name o[...]

Vigor2130 Series User’s Guide 220 4 4 . . 1 1 3 3 . . 8 8 D D a a t t a a F F l l o o w w M M o o n n i i t t o o r r This page displays the running procedure for the IP address monitored and refreshes the data in an interval of several seconds. The IP address listed here is configured in Bandwidth Management. You have to enable IP bandwidth limi[...]

Vigor2130 Series User’s Guide 221 in five minutes. The remaining time will be shown on the session column. 4 4 . . 1 1 3 3 . . 9 9 P P o o r r t t s s S S t t a a t t e e Click Diagnostics and click Ports State to open the list page. There are for LAN ports and one WAN port in your router. Through this page, you can know which port is using and y[...]

Vigor2130 Series User’s Guide 222 This page is left blank.[...]

Vigor2130 Series User’s Guide 223 5 T T r r o o u u b b l l e e S S h h o o o o t t i i n n g g This section will guide you to solve abnormal s ituations if you cannot access into the Internet after installing the router and finishing the we b configuration. Please follow sections below to check your basic installation status stage by stage. z Ch[...]

Vigor2130 Series User’s Guide 224 5 5 . . 2 2 C C h h e e c c k k i i n n g g I I f f t t h h e e N N e e t t w w o o r r k k C C o o n n n n e e c c t t i i o o n n S S e e t t t t i i n n g g s s o o n n Y Y o o u u r r C C o o m m p p u u t t e e r r I I s s O O K K o o r r N N o o t t Sometimes the link failure occurs due to the wrong network[...]

Vigor2130 Series User’s Guide 225 4. Select Obtain an IP address automatically and Obtain DNS server address automatically . F F o o r r M M a a c c O O s s 1. Double click on the current used MacOs on the desktop. 2. Open the Application folder and get into Network . 3. On the Network screen, select Using DHCP from the drop down list of Configur[...]

Vigor2130 Series User’s Guide 226 5 5 . . 3 3 P P i i n n g g i i n n g g t t h h e e R R o o u u t t e e r r f f r r o o m m Y Y o o u u r r C C o o m m p p u u t t e e r r The default gateway IP address of the router is 192.168.1.1. For some reason, you might need to use “ping” command to check the link status of the router. The most import[...]

Vigor2130 Series User’s Guide 227 5 5 . . 4 4 C C h h e e c c k k i i n n g g I I f f t t h h e e I I S S P P S S e e t t t t i i n n g g s s a a r r e e O O K K o o r r N N o o t t Open WAN>>Internet Access page and then check whether the ISP settings are set correctly. Use the Connection Type drop down list to choose Static IP/DHCP/PPPoE/[...]

Vigor2130 Series User’s Guide 228 F F o o r r S S t t a a t t i i c c U U s s e e r r s s 1. Choose Static IP as the connection type. 2. Check if IP Address, IP Mask and IP Router are set correctly (must identify with the values from your ISP). F F o o r r P P P P P P o o E E U U s s e e r r s s 1. Choose PPPoE as the connection type. 2. Check if[...]

Vigor2130 Series User’s Guide 229 F F o o r r P P P P T T P P / / L L 2 2 T T P P U U s s e e r r s s 1. Choose PPTP/L2TP as the connection type. 2. Check if Username , Password, IP address, Subnet Mask are entered with correct values that you get from your ISP . 5 5 . . 5 5 F F o o r r c c i i n n g g V V i i g g o o r r R R o o u u t t e e r r [...]

Vigor2130 Series User’s Guide 230 10. Input the Password if you have set one, then click Send . 11. There is a bar showing the upgrading process. 12. When the firmware upgrade is successf ul, the following window will pop up.[...]

Vigor2130 Series User’s Guide 231 If the message of Request Timeout. Transfer Abort ! appears, please check if the connection between the computer and the Vigor is active or not. And, if the message of Incorrect/No file name. Transfer Abort ! appears, please check if the firmware y ou download is correct for your Vigor router. Note: Please turn o[...]

Vigor2130 Series User’s Guide 232 5 5 . . 6 6 B B a a c c k k i i n n g g t t o o F F a a c c t t o o r r y y D D e e f f a a u u l l t t S S e e t t t t i i n n g g I I f f N N e e c c e e s s s s a a r r y y Sometimes, a wrong connection can be im proved by returning to the default settings. Try to reset the router by software or hardware. Warn[...]

Vigor2130 Series User’s Guide 233 5 5 . . 7 7 C C o o n n t t a a c c t t i i n n g g Y Y o o u u r r D D e e a a l l e e r r If the router still cannot work correctly after trying many efforts, please contact your dealer for further help right away. For any questions, please feel free to send e-mail to support@draytek.com.[...]