Eagle FishElite 640c manual

Pub. 988-0143-871 www.eaglesonar.com FishElite 640c & SeaCharter 640cDF Fish-finding Sonars & Mapping GPS Installation and Operation Instructions ® ®[...]

Copyright © 2005 LEI-Eagle All rights reserved. No part of this manual may be copied, reproduced, republished, transmitted or distributed for any purpose, without prior written consent of Eagle Electronics. Any unauthorized commercial distribution of this manual is strictly prohibited. Eagle ® is a registered trademark of LEI. MapCreate  , Fre[...]

i Table of Contents Section 1: Read Me First! ......................................................... 1 Capabilities and Spe cificati ons: .................................................... 3 How Eagle Sonar Works ............................................................... 5 How GPS Works ....................................................[...]

ii Pages ........................................................................................... 44 Satellite Status Page .............................................................. 44 Navigation Page ...................................................................... 45 Map Page ...........................................................[...]

iii Stop Chart ................................................................................... 80 Surface Clarity ............................................................................ 80 Zoom & Zoom Bar ....................................................................... 81 Zoom Pan ................................................[...]

iv Create Icon at Current Position ........................................... 120 Delete an Icon ....................................................................... 120 Navigate to an Icon ............................................................... 121 Routes .................................................................................[...]

v Pop-up Map Information ...................................................... 142 Draw Map Boundaries .......................................................... 142 Fill Water With White .......................................................... 142 Map Overlays (Range Rings; Lat/Long Grid) ...................... 142 Map Datum Selection .........[...]

vi WARNING! A CAREFUL NAVIGATOR NEVER RELIES ON ONLY ONE METHOD TO OBTAIN POSITION INFORMATION. CAUTION When showing navigation data to a position (waypoint), a GPS unit will show the shortest, most direct path to the waypoint. It provides navigation data to the waypoint regardless of obstructions. Therefore, the prudent navigator will not only tak[...]

1 Section 1: Read Me First! How this manual can get you out on the road, fast! Welcome to the exciting world of digital sonar and GPS! We know you are anxious to begin navigating and finding fish, but we have a favor to ask. Before you grab the unit and begin installing it, please give us a moment or two to explain how our manual can help you get t[...]

2 After you have gained some experience with your sonar, you will want to check out Section 4, which discusses more advanced Sonar Options and Other Features . When you come to a sonar menu command on the unit's screen, you can look it up in the manual by skimming over the table of contents, just flip- ping through Section 3 or scanning throug[...]

3 It's important to us and our power users, but if you don't care how many watts of power the unit has or how many waypoints it can store, skip ahead to important information on how sonar works on page 5. Back- ground on GPS begins on page 6. Capabilities and Specifications: General Display: ............................ 5.0" (12.7 cm[...]

4 Sonar Sounding Depth capability: ........... SeaCharter 640cDF : 1,500 feet (457 me- ters). FishElite 640c : 800 feet (244 meters). Actual capability depends on transducer con- figuration and installation, bottom composi- tion and water conditions. All sonar units typically read deeper in fresh water than in salt water. Depth display: ...........[...]

5 Position points: ............. 1,000 waypoints; 1,000 event marker icons. Audible alarms: ............. Arrival/off-course/anchor. Graphic symbols for waypoints or event marker icons: ................. 42. Routes: ............................. 100, up to 100 waypoints per route. Plot Trails: ...................... 10 savable; up to 10,000 points [...]

6 chart. The sonar's microprocessor calculates the time lapse between the transmitted signal and echo return to determine the distance to the object. The whole process repeats itself several times each second. Your unit can record a log of the sonar signals that scroll across the screen and save them to the MMC memory card. (These recordings a[...]

7 making software, MapCreate  6 or one of our special plug-and-play mapping cards. Some unit features — such as searching for businesses and addresses — won't work without a custom MapCreate map. There is so much detail in our background map (and even more in MapCreate) that we'll describe their contents and differences in Section [...]

8 so you can mount your unit and plug in the power. Or you might want to see how our text formatting makes the manual tutorials easy to skim. If that's the case, move on to How to Use This Manual on page 11. But, if you want to understand the current state of satellite naviga- tion, look over this segment describing how GPS and its new compani[...]

9 Remember, the unit must have a clear view of the satellites in order to receive their signals. Unlike radio or television signals, GPS works at very high frequencies. These signals can be easily blocked by trees, buildings, an automobile roof, even your body. Like most GPS receivers, this unit does not have a compass or any other navigation aid b[...]

10 of terrain! It only calculates position, it can’t know what’s between you and your destination, for example. It’s up to you to safely navigate around obstacles, no matter how you’re using this product. Free Training Aids Available Now that you know something about the technology that makes this unit possible, you are ready to start learn[...]

11 The emulator works exactly like your real sonar/GPS unit. When using the Sonar and GPS Simulators you can play back sonar logs, run GPS routes and trails, even create real waypoints you can use in the field. You can take snapshots of the Sonar Chart and print them or e-mail them to friends. And that is just some of the material available on our [...]

12 For example, instructions for navigating a trail would look like this: 1. From the Map Page, press MENU | MENU | ↓ to M Y T RAILS | ENT . 2. Press ↓ to Trail 1 | ENT | → to N AVIGATE | ENT . 3. You are asked to wait while it converts the trail into a route. 4. The wait message disappears and the unit begins showing navigation information a[...]

13 Section 2: Installation & Accessories Preparations You can install the unit in some other order if you prefer, but we rec- ommend this installation sequence: Caution: You should read over this entire installation section before drill- ing any holes in your vessel! 1. Determine the approximate location for the unit, so you can plan how and wh[...]

14 Remember, transducer location is the most critical part of a so- nar installation. Recommended Tools and Supplies If you prefer the option of routing the cable through the transom, you will need a 5/8" drill bit. (If you intend to install an additional speed or temp sensor and route its cable through the same hole in the transom, you will n[...]

15 typically have large outboard motors capable of propelling the boat at speeds faster than 35 mph. Typically, a good transom location on aluminum boats is between the ribs closest to the engine. 3. The transducer should be installed with its face pointing straight down, if possible. For shoot-thru applications: Many popular fishing boat hulls hav[...]

16 Align transducer centerline with hull bottom. A dual frequency transducer (left) and a single frequency transducer (right). There, however, are times when you may need to adjust the transducer slightly higher or lower. (The slots in the mounting brackets allow you to loosen the screws and slide the transducer up or down.) If you fre- quently los[...]

17 Second, the transducer angle cannot be adjusted for the best fish arches on your sonar display. (This is not an issue for flasher-style sonars.) Lack of angle adjustment can be particularly troublesome on hulls that sit with the bow high when at rest or at slow trolling speeds. Third, a transducer CAN NOT shoot through wood and metal hulls. Thos[...]

18 ing illustrations. Notice there are letters molded into each ratchet. Place the ratchets into the bracket wit h the letter "A" align ed with the align- men t mar k molded into the bracket. Place the ratchets onto the trans- ducer with the letter "A" aligned with the 12 o' cl oc k position on the transducer stem. These po[...]

19 Reassemble the transducer and bracket and place them against the transom. Again, check to see if you can move the transducer so it's par- allel with the ground. If you can, then go to step 3A. If it doesn't, repeat step 2A, but use a different alignment letter until you can place the transducer on the transom correctly. Insert bolt and[...]

20 3. Assembling the transducer. A. One-piece bracket: Once you determine the correct position for the ratchets, assemble the transducer as shown in the following figure. Don't tighten the lock nut at this time. Assemble transducer and bracket. B. Two-piece bracket: Once you determine the correct position for the ratchets, assemble the transdu[...]

21 5. Attaching transducer to transom. A. One-piece bracket: Remove the transducer from the bracket and re- assemble it with the cable passing through the bracket over the bolt as shown in the following figures. For single-frequency Skimmer, route cable over bolt and through bracket. Side view shown (left) and seen from above (right). Both bracket [...]

22 WARNING: Clamp the transducer cable to the transom close to the transducer. This can prevent the transducer from enter- ing the boat if it is knocked off at high speed. If you need to drill a hole in the transom to pass the connector through, the required hole size will be 5/8". Caution: If you drill a hole in the transom for the cable, mak[...]

23 Transducer mounted on trolling motor, side view. Transducer Orientation and Fish Arches If you do not get good fish arches on your display, it could be because the transducer is not parallel with the ground when the boat is at rest in the water or at slow trolling speeds. Transducer angles and their effects on fish arches. If the arch slopes up [...]

24 Shoot-Thru-Hull Preparation Hulls With Flotation Materials The transducer installation inside a fiberglass hull must be in an area that does not have air bubbles in the resin or separated fiberglass lay- ers. The sonar signal must pass through solid fiberglass. A successful transducer installation can be made on hulls with flotation materials (s[...]

25 Shoot-thru-hull transducer locations for high speed or trolling speed operation. To choose the proper location for shoot-thru-hull mounting, follow these testing procedures: (You may need a helper to complete these steps.) 1. Anchor the boat in about 30 feet of water. Add a little water to the sump of the boat. Plug the transducer into the sonar[...]

26 If you can't get an acceptable bottom signal, try turning up the sensitivity by three or five keystrokes and then move the transducer around once more. If you find a spot that works, mark it and move on to step 4. If you have to turn up sensitivity by more than five keystrokes to get a good signal, the transducer should be mounted on the ou[...]

27 Epoxy transducer to hull. WARNING: Use only the epoxy available from LEI. It has been for- mulated to work with these installation procedures. Other epoxy types may be too thin or may not cure to the right consistency for optimum transducer performance. 2. The epoxy consists of the epoxy itself and a hardener. Remove the two compounds from the p[...]

28 5. After the epoxy has cured, route the cable to the sonar unit and it's ready to use. Speed/Temperature Sensors This unit can accept as many as two temperature sensors, which can be used to monitor the temperature of surface water, a live well or some other location. These units can also accept an optional speed sensor for showing speed an[...]

29 Sonar unit with external temp sensor, external speed sensor, or combo speed/temp sensor. The primary temperature sensor is built into the transducer. Optional Speed Sensor Installation All the units in this series can display speed and distance traveled, but only the SeaCharter 640cDF comes packed with a speed sensor. If you wish to purchase an [...]

30 Once you have determined the proper location for the unit, place the sensor on the transom. The bottom of the bracket should be flush with the hull's bottom. Using the sensor as a template, mark the hull for the screw's pilot holes. Drill four 1/8" holes, one in each end of the slots. Mount the sensor to the hull using #8 stainles[...]

31 Power Connections The unit works from a 12-volt battery system. For the best results, at- tach the power cable directly to the battery. You can attach the power cable to an accessory or power buss, however you may have problems with electrical interference. Therefore, it's safer to go ahead and attach the power cable directly to the battery[...]

32 WARNING: This product must be independently fused with the en- closed 3-amp fuse (or equivalent), even if you connect to a fused accessory or power buss. If a malfunction happens inside the unit, extensive dam- age can occur if the enclosed fuse is not used. As with all electrical devices, this unit could be damaged to a point that it is unrepai[...]

33 work well if you have a cab-over design pickup truck camper or motor home. If dashboard reception is poor, simply relocate the antenna mod- ule elsewhere on the vehicle for a clearer view of the sky. NMEA Cable Connections NMEA is a standard communications format for marine electronic equipment. For example, an autopilot can connect to the NMEA [...]

34 gimbal bracket to a swivel mount, which can be used on the dash or overhead mounting positions. Optional R-A-M mounting system. Bracket Installation Mount the unit in any convenient location, provided there is clearance behind the unit when it's tilted for the best viewing angle. You should also make sure there is enough room behind the uni[...]

35 Install the gimbal bracket. Position the bracket so the arms slope to- ward the front of your unit. Drill a 1-inch (25.4 mm) hole in the dash for the power and transducer cables. The best location for this hole is immediately under the gimbal bracket location. This way, the bracket can be installed so that it covers the hole, holds the cables in[...]

36 Pass the power cable's bare-wire end down though the hole from the top. If you want, you can fill in the hole around the cables with a good marine sealant compound. (Some marine dealers stock cable hole cov- ers to conceal the opening.) No matter what type of installation you prefer, be sure to leave enough slack in the cables to allow tilt[...]

37 Portable Installation Like many Eagle products, this unit is capable of portable operation by using an optional portable power pack (PPP). The power pack and an optional portable transducer expand the uses for your sonar unit. The PPP makes it easy to use the unit on your boat or take it to the dock, on a float tube, on an ice fishing trip or us[...]

38 Additional MMC cards are available from LEI Extras. See ordering in- formation inside the back cover of this manual. MMCs and SD cards are also available at many camera and consumer electronics stores. The MMC slot is located in a compartment on the front of the case. The compartment door is located at the lower right corner. The following figur[...]

39 MapCreate™ 6 CD-ROM (left). MMC card reader for USB ports (right). NOTE: When you first turn on the unit, the Map Page appears. If you would rather start learning about GPS operation, jump to Sec. 6, Basic GPS Operations . Remember: you don't need to read this manual from cover-to-cover to get going. We designed it so you can skip around [...]

40 Notes[...]

41 Section 3: Basic Sonar Operation This section addresses the unit's most basic sonar operations. The in- structions presented in Sec. 3 follow a chronological order. Sec. 4, Sonar Options & Other Features , will discuss other more advanced functions and utilities. Material in Sec. 4 is arranged in alphabetical order. Before you turn on t[...]

42 4. ARROW KEYS – These keys are used to navigate through menus, make menu selections, move the map and sonar chart cursors and enter data. 5. ENT/ICONS – The Enter key allows you to save data, accept values and execute menu commands. It is also used to create event marker icons. 6. EXIT – The Exit key lets you return to the previous screen,[...]

43 You can access the Main Menu from any of the four Page screens by pressing MENU | MENU . To clear the menu screen and return to the page display, press EXIT . Remember: our text style for " MENU | MENU " means "press the Menu key twice." See a full explanation of our instruction text formatting on page 11, How to use this man[...]

44 Timers : controls the up timer, down timer and alarm clock settings. Browse MMC Files : allows you to view the installed MMC card and the files it contains. Pages The unit has four Page displays. They are the Satellite Status Page, Navigation Page, Map Page and Sonar Page. They are accessed by press- ing the PAGES key, then using ← → to sele[...]

45 Satellite Status Page showing satellite lock-on with a 3D position acquired (latitude, longitude and altitude) with WAAS reception. Navigation Page This screen has a compass rose that shows your direction of travel and direction to a recalled waypoint. To get to the Navigation Page pres s PAGES | ← → to N AVIGATION | EXIT . This page represe[...]

46 Map Page showing position on Bull Shoals Lake, Arkansas. The full map option (left). Map with sonar option (right). Map Page is also the default screen that appears when you turn on the unit. To get to the Map Page from another page pres s PAGES | ← → to M AP | EXIT . You can display a split screen showing both the Map and Sonar pages at the[...]

47 The four Sonar Page display modes: Full Sonar Chart (left). Split Zoom display mode (right). Split Frequency mode (left) and Digital Data mode (right). Full sonar chart mode. Surface clutter Structure Bottom signal Fish arches Depth scale Digital data overlay (depth & temperature) Surface signal Zoom bar FasTrack bar graph[...]

48 You can customize how the Sonar Page displays its pictures and other data in many ways. Your unit also includes several special sonar features and options that can help you better interpret the underwater scene. We will discuss all of those features and options in Sec . 4, but to show you how easy thi s uni t is t o op erat e, the following page[...]

49 Basic Sonar Quick Reference 1. Mount the transducer, antenna and unit. Connect the unit to electric power and the transducer. (If GPS operation is desired, connect GPS antenna, too.) Make sure the MMC is in. (See complete installation de- tails beginning on page 6.) 2. Launch your boat. 3. To turn on the unit, press and release PWR key. 4. Openi[...]

50 Sonar Operations As you can see from the quick reference, basic operation is pretty easy, right out of the box. If you are a sonar novice, try operating the unit with the de- fault settings until you get a feel for how it is working. As you are learning the basics, there is one setting you might want to tinker with from time to time — Sensitiv[...]

51 Adjusting sensitivity in Auto Sensitivity Mode is similar to manually ad- justing a car's speed with the accelerator pedal while cruise control is on. You can tell the car to run faster, but when you let off the gas the cruise control automatically keeps you from running slower than the minimum speed setting. In the unit, auto mode will let[...]

52 S ENSITIVITY | ENT | ↑ to S ENSITIVITY | ENT . Press ↓ ↑ to pick a different sensitivity setting. When it is set at the desired level, press EXIT . Tip: While you are experimenting and learning, it is possible to scramble the settings so the sonar picture disappears from your screen. If that happens, remember it is easy to switch back to f[...]

53 Section 4: Sonar Options & Features ASP  (Advanced Signal Processing) The ASP  feature is a noise rejection system built into the sonar unit that constantly evaluates the effects of boat speed, water conditions and interference. This automatic feature gives you the best display pos- sible under most conditions. The ASP feature is an ef[...]

54 Alarms This unit has three types of sonar alarms. The first is the Fish Alarm. It sounds when the Fish I.D.  feature determines that an echo is a fish. Another alarm is the Zone Alarm, which consists of a bar on the side of the screen. Any echo on the chart that appears inside this bar triggers this alarm. The last alarm is the Depth Alarm, w[...]

55 3. Press ↑ ↓ to change the first number, then press → to move the cur- sor to the next number and repeat until the depth is correct. Press ENT . 4. Press ← to S HALLOW A LARM E NABLED | ENT . To turn on the alarm, high- light the S HALLOW A LARM E NABLED box and press ENT . To adjust and turn on the deep alarm: 1. From the Sonar Alarms m[...]

56 Fish Alarm Use the fish alarm for a distinctive audible alarm when fish or other suspended objects are detected by the Fish I.D.  feature. Fish I.D. must be turned on for the Fish Alarm to work. A different tone sounds for each fish symbol size shown on the display. Sonar Alarms menu with Fish Alarm selected. The check box to the left is blan[...]

57 Chart Speed The rate echoes scroll across the screen is called chart speed. The de- fault is maximum. We recommend you keep the default setting for most all fishing conditions. You may consider experimenting with chart speed when you are sta- tionary or drifting slowly. Sometimes the unit will display better im- ages when chart speed is adjusted[...]

58 For example, a soft, muddy or weedy bottom returns a weaker signal which is shown with a narrow, colored line (dark blue tinged with red or a little yellow.) Since fish are among the weakest echoes, they show up mostly as blue arches. A hard bottom or other relatively hard target returns a strong signal which causes a wider brightly colored line[...]

59 A little ColorLine (left) indicates a soft bottom, probably sand or mud. Wider ColorLine (right) indicates a harder, rocky bottom. Customize Page Displays Every Page display with digital data boxes may be customized to pro- vide on-screen information. The data is divided into categories in the Customize menu. These cate- gories include GPS Data,[...]

60 Digital Data box containing Water Temp is highlighed (left). Data Viewer with GPS Data and Navigation categories expanded (right). Selecting the category name and pressing ENT will bring up the cate- gory's contents.. An expanded category (one with a "-" next to its name) can be collapsed to hide its contents and make more room on[...]

61 The cursor can be moved to any location on the screen, letting you pin- point the depth of a target. 1. From the Sonar Page, press MENU | ↓ to D EPTH C URSOR | ENT . 2. The depth cursor appears. Press ↓ to lower the cursor line. Press ↑ to raise the cursor line. 3. To clear the depth cursor, press EXIT . Depth Range - Automatic When turned[...]

62 3. Press ↓ ↑ to select a different depth range. A horizontal blue bar highlights the selected range. 4. When the new range is selected, press EXIT to close the menu. NOTE: The sonar's depth capability depends on the transducer installa- tion, water and bottom conditions and other factors. FasTrack  This feature automatically converts[...]

63 The sonar's microcomputer is sophisticated, but it can be fooled. It can not distinguish between fish and other suspended objects such as trot- lines, turtles, submerged floats, air bubbles, etc. Individual tree limbs extending outwards from a group of limbs is the hardest object for the Fish I.D. feature to distinguish from fish. You may s[...]

64 To turn on FishTrack: NOTE: These steps turn on FishTrack and Fish I.D. at the same time. 1. From the Sonar Page, press MENU | ↓ to S ONAR F EATURES | ENT . 2. Press → ↓ to F ISH D EPTHS | ENT | EXIT | EXIT . To turn off FishTrack, repeat the instructions in step 1. Turning off FishTrack in this manner will not turn off Fish I.D. symbols. [...]

65 sonar. In many of those cases, you will see a 50 kHz transducer fre- quency in use because the wider cone angle lets them watch the bait. Sonar Features menu with 50 kHz frequency selected (left). 200 kHz frequency selected (right). To change the frequency setting to 50 kHz: 1. From the Sonar Page, press MENU | ↓ to S ONAR F EATURES | ENT . 2.[...]

66 Sonar Page menu with Log Sonar Chart Data selected (left). Sonar Chart Logging menu with Start Logging command selected (right). To record or log chart data: 1. Press MENU | ↓ to L OG S ONAR C HART D ATA | ENT . 2. To record data using the default settings, press ENT . The menu clears and the Sonar Page title bar shows the name of the file you[...]

67 You can select items from any of these categories for display, in any combination. The category divisions are there only to help you sort through the information. Overlay Data menu with Press Ent to add highlighted (left). Data viewer with Navigation, Trip Calculator and Time categories expanded (right). To overlay information on your screen: 1.[...]

68 From Overlay Data Shown (left) press ENT to see Data Viewer (center). Select a category and press ENT , then choose a data option to display and press ENT to turn it on (right). To remove overlaid data: 1. While on the Page that shows the data you want to remove, press MENU | ↓ to O VERLAY D ATA | ENT . 2. You will see a list of the overlay da[...]

69 3. The data begins to flash on your screen. Use ↓ ↑ ← → to move the data to a new location on the display. 4. When have the data in the desired position, press EXIT | EXIT . NOTE: The Customize and Overlay Data commands use the same informa- tion categories. The difference between the two commands is Cus- tomize changes only the data in [...]

70 you change the Ping Speed to any setting greater than 50 percent, the unit automatically enters HyperScroll mode. These faster ping rates allow you to maintain a high-detail picture on the screen. The ping rate helps the screen refresh rate and chart scroll speed keep pace with the speed of the boat. When using HyperScroll, you may also need to [...]

71 This allows you to better see sonar returns, just as you would on a flasher sonar unit. For more information on FasTrack, see its entry in this section. Reset Options This command is used to reset all features, options and settings to their factory defaults. This is useful when you have changed several settings and want to return the unit to the[...]

72 Set Keel Offset This unit measures water depth from the face of the transducer. Since the transducer is installed below the water surface, the distance dis- played by the digital depth, chart depth scale, chart cursor or fish sym- bols is not the exact water depth. If the transducer is 1 foot below the surface, and the screen shows the water dep[...]

73 3. Press → to the first number, then press ↑ to change the number to 1. 4. Press → to the second number, them press ↑ to change the num- ber to 5 and press EXIT . The depth indicators now accurately show the water depth from surface to bottom. Sensitivity & Auto Sensitivity The sensitivity controls the ability of the unit to pick up [...]

74 Sonar Menu with Sensitivity command selected (left). The Sensitivity Control Bar (right). To adjust sensitivity in manual mode: 1. First, turn off Auto Sensitivity: from the Sonar Page, press MENU | ↓ to A UTO S ENSITIVITY | ENT . 2. Press ↑ to S ENSITIVITY | ENT and the Sensitivity Control Bar appears. Press ↓ ↑ to pick a different sens[...]

75 Sonar Page & Sonar Chart Display Options The Sonar Page Menu offers four chart display options. To access them, press PAGES | → to S ONAR | ↓ to Option Name | EXIT . Pages Menu, showing sonar chart display options. Full Sonar Chart This is the default mode used when the unit is turned on for the first time or when it is reset to the fact[...]

76 Full Sonar Chart (left). Split Zoom Sonar Chart (center) with left win- dow zoomed to 2X. Split Zoom chart (right) zoomed to 4X. Split Zoom Sonar Chart A split chart shows the underwater world from the surface to the bot- tom on the right side of the screen. The left side shows an enlarged ver- sion of the right side. The zoom range shows at the[...]

77 Sonar Page Menu showing Customize command highlighted (left). The first data box (Water Temp) is flashing (right). 1. From the Digital Sonar Page, press MENU | ↓ to C USTOMIZE | ENT . 2. The title bar begins flashing on the second box from the top, indicat- ing its contests can be changed. Press ENT , which will launch the Data Viewer menu wit[...]

78 select a display option. With the option highlighted, press ENT to turn it on (check) and turn it off (uncheck). When you have selected a data op- tion, press ENT | EXIT . The data you chose is now displayed in the se- lected digital data box. To change other boxes on the Sonar Digital Page, use ↑ ↓ to select another digital data box and rep[...]

79 Main Menu with Sonar Setup command selected (left). Submenu with Sonar Simulator command selected (center). Sonar Simulator menu (right), with simulator turned off (box is unchecked). NOTE: With Simulate Position checked, the simulator will automatically run the GPS simulator, if GPS data was recorded with the sonar log. 2. To use the default so[...]

80 3. Press ↓ or ↑ to select chart name | ENT | ↑ to S ONAR S IMULATOR O N | ENT | EXIT . While you are in the Sonar Simulator menu, do not forget to check Simulate Position if you want to run the sonar and GPS simulators simultaneously. As you review sonar logs, you can create waypoints at sites you want to revisit. While the simulator is ru[...]

81 changing the sensitivity of the receiver, decreasing it near the surface and gradually increasing it as the depth increases. There are three levels of surface clarity available: off, low, medium and high. The default level is off. To adjust the Surface Clarity level: 1. From the Sonar Page, press MENU | ↓ to S ONAR F EATURES | ENT | ↓ to S U[...]

82 Sonar Page (left). Sonar Page zoomed 2X (center). Sonar Page zoomed 4X (right). Zoom Pan Your unit has the handy ability to quickly zoom in on any portion of the water column. Zoom Pan lets you rapidly move the zoomed area up and down the display. By pointing your zoom at different portions of the chart as it scrolls, you can get a close-up look[...]

83 Section 5: Sonar Troubleshooting If your unit is not working, or if you need technical help, please use the following troubleshooting section before contacting the factory customer service department. It may save you the trouble of returning your unit for repair. For contact information, refer to the last page, just inside the back cover of this[...]

84 3. The water may be deeper than the sonar's ability to find the bottom. If the sonar can't find the bottom signal while it's in the automatic mode, the digital sonar display will flash continuously. It may change the range to limits far greater than the water you are in. If this hap- pens, place the unit in the manual mode, then c[...]

85 To eliminate or minimize the effects of electrical noise, first try to de- termine the cause. With the boat at rest in the water, the first thing you should do is turn all electrical equipment on the boat off. Make sure the engine is also off. Turn your sonar on, then turn off Noise Reject [also known as the ASP feature (Advanced Signal Processi[...]

86 Notes[...]

87 Section 6: Basic GPS Operations This section addresses the unit's most basic GPS operations. The tuto- rials presented in Sec. 6 follow a chronological order. Sec. 7, Advanced GPS Operations , will discuss other more advanced functions and utili- ties. Material in Sec. 7 is arranged in alphabetical order. Before you turn on the unit and fin[...]

88 4. ARROW KEYS – The arrow keys are used to navigate through menus, enter data, make menu selections, move the map cursor and sonar chart cursor. 5. ENT/ICONS – The Enter key allows you to save data, accept values or execute menu commands. It is also used to create event marker icons. 6. EXIT – The Exit key lets you return to the previous s[...]

89 Main Menu. The Main Menu commands and their functions are: Screen : changes the contrast or brightness of the display screen. Sounds : enables or disables the sounds for key strokes and alarms and sets the alarm style. Transparency : adjusts the level of transparency for menus. Alarms : turns GPS or sonar alarms on or off and changes alarm thres[...]

90 Pages The unit has four Page displays: Satellite Status Page, Navigation Page, Map Page and Sonar Page. They are accessed by pressing the PAGES key, then using ← → to select a Page. Clear the Pages Menu by pressing EXIT . Map Page display options. Sonar Page The Sonar Page displays the sonar chart, a view of the water column from the surface[...]

91 Satellite Status Page. The first figure (left) indicates unit has not locked on to any satellites and does not have a fix on its position. The second figure (right) shows satellite lock-on with a 3D position acquired (lati- tude, longitude and altitude), and WAAS reception. This screen shows a graphical view of the satellites in view. Each satel[...]

92 The Satellite Status Page has its own menu, which is used for setting various options. To access the Satellite Status Page Menu, from the Status Page, press MENU . Navigation Page This screen has a compass rose that not only shows your direction of travel, but also the direction to a recalled waypoint. To get to the Navi- gation Page pres s PAGE[...]

93 Speed is the velocity you are making over the ground. If you want, you can customize the Speed data box to display Closing Speed instead. Closing Speed is also known as velocity made good. It is the speed you are making toward the waypoint. For instructions, see the Customize Page Displays entry in Sec. 8. Track is the heading or the current dir[...]

94 Travel Time is the time it will take to reach your destination at your present closing speed. You can also customize the time data box to show Arrival Time instead. Arrival Time is the local time it will be when you arrive at the destination, based upon your present closing speed and track. In the preceding figure, the driver is headed northwest[...]

95 Map Page opening screen (left). Map zoomed to 100 miles (center). Map zoomed to 10 miles (right). Over Zoomed, listed at the top of the map screen (right) means you have reached the detail limits in an area cov- ered only by the basic background map. Zooming in any closer will reveal no more map details because a high-detail custom map has not b[...]

96 Background map vs. MapCreate map content The background map includes, low-detail maps of the whole world (con- taining cities, major lakes, major rivers, political boundaries) and me- dium-detail maps of the United States. The medium-detail U.S. maps contain all incorporated cities, shaded metropolitan areas, county boundaries; shaded public lan[...]

97 When the map is zoomed out far enough, most POIs appear as square dots (left). As you zoom in closer, the symbols become readable icons. In the 0.2-mile zoom example (right), the cursor has selected the Cupps Café POI, which triggers a pop-up box with the POI name Tip: In some urban areas, businesses are so close to one another their POI icons [...]

98 Two Position Format map page option. In pages that have two major windows you can toggle back and forth between the two windows by pressing PAGES | PAGES . This allows you to change the active map. Only when a map is active are you able to make adjustments to it. Pages Menu with Two Map option selected (left). Map Page with two map windows (righ[...]

99 On the Map with Sonar page, you can only change size, not switch lay- out. It is always two vertical windows. Press EXIT to clear the four flashing arrows. (From left to right) Fig. 1. Resize Window command on the GPS Page menu. Fig. 2. Two Maps page display with four flashing arrows on the dividing centerline. Fig. 3. The centerline has been mo[...]

100 Basic GPS Quick Reference Start outdoors, with a clear view of the open sky. As you practice, try navigating to a location at least a few blocks away. While you're learning, navigation in too small an area will constantly trigger arrival alarms. 1. Connect the unit to electric power and the antenna module. Make sure the MMC is in. (See com[...]

101 Find Your Current Position Finding your current position is as simple as turning on the unit. Un- der clear sky conditions, the unit automatically searches for satellites and calculates its position in approximately one minute or less. NOTE: Clear sky conditions means open sky, unobstructed by terrain, dense foliage or structures. Clouds do not[...]

102 The selected wreck (the Empress) to the southeast is 12.81 miles away. Selecting Any Map Item With the Cursor 1. Use the zoom keys and the arrow keys to move around the map and find the item you wish to select. 2. Use the arrow keys and center the cursor cross-hair on the desired ob- ject. On most items, a pop-up box will give the name of the s[...]

103 1. After the unit has acquired a position, press WPT | ↓ to POI- R ESTAURANTS . 2. You could search the entire restaurant category, but in this example we will narrow our search. Press → ↓ to F AST F OOD C HAINS | ENT | ↓ to N EAREST | ENT . 3. A list of restaurants will appear with the closest at the top of the list, and the one furthe[...]

104 you could by pressing Enter. The Go To waypoint command is already highlighted. But we just want to see it on the map, so press ↓ to F IND O N M AP | ENT . 6. The unit's map appears, with the cursor crosshairs highlighting the restaurant' s POI symbol. A pop-up data box shows the POI's name. A data box at the bottom of the scre[...]

105 To create and save a Waypoint: These first two techniques use the Quick Save method, the fastest and easiest way to create a waypoint. Create Waypoint at Current Position While you are traveling, press WPT | WPT . The waypoint is saved and automatically given a name with a sequential number, such as way- point 003. The waypoint symbol and numbe[...]

106 Sequence for setting a waypoint. Step 1: while traveling, press WPT to call up Find Waypoint screen (seen in Step 2) and set a point. Step 3: a message says the waypoint has been saved. Step 4: vehicle continues on its way; number waypoint symbol is visible on map. Create Waypoint on Map 1. Use the arrow keys to move the cursor to the place whe[...]

107 4. Press ↓ to L ONGITUDE | ENT . Enter the longitude by pressing ↑ ↓ to change the first character, then press → to the next character and repeat until the longitude is correct. Press ENT , then EXIT | EXIT to return to the previous page display. The waypoint is saved and automatically given a name with a sequential number, such as wayp[...]

108 Set Man Overboard (MOB) Waypoint One of boating's most terrifying events is having a friend or family member fall overboard. This unit has a man overboard feature that shows navigation data to the location where the feature was activated. To activate it, press the ZOUT and ZIN keys at the same time. Your posi- tion at the time these keys a[...]

109 1. Use the cursor with the zoom in and zoom out keys to move around the map until you find a location you want to go to. 2. Center the cursor over the location to select it. See the example in the following figure. Map items like waypoints, Points of Interest and towns among others, can be selected and appear highlighted with a pop-up box. Othe[...]

110 To stop navigating to the cursor, use the Cancel Navigation command. Press MENU | MENU | ↓ to C ANCEL N AVIGATION | ENT | ← to Y ES | ENT . The unit stops showing navigation information. Navigate to a Point of Interest You can use the Navigate to Cursor command for POIs in view on the map, just use the cursor to select the POI. The other me[...]

111 Sequence for saving a trail and beginning a new one. My Trails com- mand (left). The Trails Menu (center). The arrow to the right of Trail 3 indicates the trail is active and the check to the left indicates the trail is visible on the map display. The third figure (right) shows the Edit Trail menu, with the Name command selected. To Save a Trai[...]

112 To turn off trail display: 1. Press MENU | MENU | ↓ to M Y T RAILS | ENT . 2. Press ↓ to enter the Saved Trail list, then use ↑ ↓ to select the de- sired Trail Name | ENT . 3. Press ↓ → to V ISIBLE | ENT . To return to the previous page, press EXIT repeatedly. Repeat the steps above to the turn on the trail display. Navigating Trail[...]

113 NOTE: If you are already located at or near the beginning of your trail, the arrival alarm will go off as soon as you hit Enter. Just press EXIT to clear the alarm and proceed. 5. Now, begin moving and let your unit guide you. 6. When you reach your destination, be sure to cancel your navigation. Press MENU | MENU | ↓ to C ANCEL N AVIGATION |[...]

114 course line. To see the red course line, you must turn off the visible trail option. The Navigation Page will show only the red course line, unless you are recording a new trail. The bearing arrow on the compass rose points to the next waypoint on the trail. As you travel, the arrival alarm will go off when you near a trail way- point and the b[...]

115 Navigate a Back Trail 1. Press MENU | MENU | ↓ to M Y T RAILS | ENT . 2. Press ↓ to enter the Saved Trail list, then use ↑ ↓ to select the de- sired Trail Name | ENT . 3. Press ↓ → to N AVIGATE | ENT . 4. Press ↓ → to R EVERSE R OUTE | ENT | ← to N AVIGATE | ENT . The unit shows navigation information along the trail, in rever[...]

116 You must enter which way you want to transfer data, from an MMC card to the unit (load) or from the unit to an MMC card (save). GPS data automatically recorded in the unit's internal memory must be saved to the MMC (as a GPS Data File) in order to store it on your per- sonal computer. GPS Data Files stored on an MMC must be copied from the[...]

117 These figures (from left to right) show the menu sequence for naming and saving a GPS Data File from the unit's memory to an MMC. 4. Loading to unit memory : There may be more than one GPS Data File (*.USR) on the card. To select a file, press ENT to activate the selec- tion box, use ↓ ↑ to highlight the file, then press ENT to accept [...]

118 These figures show the menu sequence for loading a GPS Data File from an MMC into the unit's memory. Cancel Navigation You can turn off any of the navigation commands after you reach your destination or at any other time by using the Cancel Navigation com- m a n d . Press MENU | MENU | ↓ to C ANCEL N AVIGATION | ENT | ← to Y ES | ENT .[...]

119 Section 7: Advanced GPS Operations Find Distance Current Position to Another Location 1. While on the Map Page press MENU | ↓ to F IND D ISTANCE | ENT . 2. Center the cursor crosshairs on the position you want to find the dis- tance to. A rubber band line appears, connecting your current position to the cursor's location. The distance al[...]

120 Icons Icons are graphic symbols used to mark some location, personal point of interest or event. They can be placed on the map screen, saved and re- called later for navigation purposes. These are sometimes referred to as event marker icons. This unit has 42 different symbols to choose from when creating an icon. Icons are similar to waypoints,[...]

121 1. Press MENU | ↓ to D ELETE M Y I CONS | ENT . 2. Press ↓ to D ELETE A LL I CONS , D ELETE B Y S YMBOL or D ELETE F ROM M AP and press ENT . Delete icons menu. The Delete All Icons confirmation message will appear. Press ← to Y ES | ENT . All icons will be deleted from the map. The Delete by Symbol command will launch the Select Symbol m[...]

122 A route allows you to navigate through several waypoints without having to reprogram the unit after arriving at each waypoint. Once programmed into the GPS unit, a route provides the option of navigat- ing forward through the route waypoints or in reverse order. You can even begin navigating in the middle of a route. Create and Save a Route You[...]

123 2. Press ↑ to N EW R OUTE , then press ENT . (To add to an existing route, press ↓ ↑ to route name | ENT .) 3. Press ↓ to E ND OF R OUTE | ENT | ↓ to A DD F ROM M AP | ENT . The Map Page appears with the cursor showing. Edit Route menu (left). Edit Route Waypoints menu (right) with Add From Map command selected. 4. Use the Zoom and ar[...]

124 Route creation sequence, continued: Fig. 4. Point (3) set at channel mouth. Fig. 5. Waypoint (4) set further south along the beach, at a recognizable landmark. The route will end with waypoint 5 at an oil platform. Fig. 6. Press EXIT to save the route and you return to this screen. 6. Move the cursor to the next point in the route, a spot where[...]

125 Edit a Route Name 1. From the N AVIGATION P AGE , press MENU | ENT or from the M AP P AGE press MENU | MENU | ↓ to R OUTE P LANNING | ENT . 2. Highlight Saved Route Name | ENT | ↑ to Name | ENT . 3. Press ↑ ↓ to change the first character, then press → to move to the next character and repeat until the name is correct. Press ENT . To [...]

126 Route Planning command on Main Menu (left). Routes menu (center). Edit Route menu (right) with Navigate Route command is selected. 2. Press ↓ to select saved route name | ENT . Highlight N AVIGATE and press ENT . 3. Upon arrival at your destination, cancel navigation. Press MENU | MENU | ↓ to C ANCEL N AVIGATION | ENT | ← to Y ES | ENT . [...]

127 Trails Delete a Trail This is the command used to erase or delete a trail. Press MENU | MENU | ↓ to M Y T RAILS | ENT | ↓ to trail name | ENT | → to D ELETE T RAIL | ENT | ← to Y ES | ENT . To Delete all trails at once : 1. Press MENU | MENU | ↓ to M Y T RAILS | ENT . 2. Press → to D ELETE A LL | ENT | ← to Y ES | ENT . Edit a Tra[...]

128 then press → to the next character and repeat until the pattern is cor- rect. Press ENT . To get back to the main page press EXIT repeatedly. Edit Trail Menu with Pattern option selected (left). Edited trail with dotted line pattern (right). Utilities Utilities are useful tools for traveling or for outdoor activities. Alarm Clock To get to th[...]

129 is highlighted in the list, press ENT | ENT . Use ↓ to select D ELETE W AYPOINT then press | ENT | ← to Y ES | ENT . To return to the main page display, press EXIT repeatedly. To delete a waypoint from the map: 1. Use the arrow keys to select a waypoint with the cursor. 2. Press WPT to view the W AYPOINT I NFORMANTION screen, then ↓ to D [...]

130 Selecting a Waypoint To select a waypoint on the map center the cursor crosshairs on the waypoint. A red border will appear around the waypoint. Set a Waypoint by Average Position A waypoint set by average position is created after several position readings have been averaged. This boosts position accuracy, helping to eliminate errors caused by[...]

131 Section 8: System & GPS Setup Alarms This unit has three GPS alarms: Arrival Alarm, Off Course Alarm and Anchor Alarm — the only one of the three set to Off by default. You can set an arrival alarm to flash a warning message and sound a tone when you cross a preset distance from a waypoint. For example, if you have the arrival alarm set t[...]

132 IMPORTANT ALARM NOTES: Anchor Alarm - The anchor alarm may be triggered even when you are sitting still. This usually happens when using small — less than .05 mile — anchor alarm ranges. Arrival Alarm - If the arrival alarm distance is set to a small num- ber, the unit may not show navigation data to the next waypoint af- ter you arrive at [...]

133 Menus for changing Com Port settings. For assistance in configuring the unit to communicate with another device, consult the factory. Customer service phone numbers are in the back of this manual. Also see the entry below for Configure NMEA . Configure NMEA You can configure the unit to use specific NMEA sentences. 1. Press MENU | MENU | ↓ to[...]

134 • VLW transmits the distance traveled through water as meas- ured by the paddle wheel. • VHW transmits the water speed as measured by the paddle wheel. 4. When the desired prefixes are turned on, press EXIT repeatedly to get back to the main page display. Coordinate System Selection The Coordinate System Menu lets you select the coordinate [...]

135 The Military Grid Reference System (MGRS) uses two grid lettering schemes, referred to as standard and standard + 10 MGRS on this unit. Your position and datum in use determines which one to use. If you use standard and your position is off significantly, then try the alternate. NOTE: When the position format is changed, it affects the way all [...]

136 To configure a map fix: To use this format, you need to follow these steps in order. Take a map of the area and determine a reference latitude/longitude. NOTE: In order for this system to work, the latitude/longitude lines must be parallel with the edge of the map. USGS maps are parallel, oth- ers may not be. Also, this works better with smalle[...]

137 command S ET A S O RIGIN selected. Press ENT and the unit returns to the Configure Map Fix menu. Finally, press EXIT to close this menu. Now press ↑ to C OORD S YSTEM | ENT , select M AP F IX from the list and press ENT . Press EXIT repeatedly to get back to the main page display where all position information now is shown as a distance from [...]

138 5. Use ↑ ↓ to change the data in another digital data box or press EXIT to return to normal operation. Customize Navigation Page While on the Navigation Page, press MENU | ↓ to C USTOMIZE | ENT . The digital data box at the top of the screen will begin to flash. 1. Press ENT if you want to change the data in that box or use ↓ ↑ to sel[...]

139 the arrow keys — S TEER WITH A RROWS command — or by setting the track and speed in the dialog boxes provided on the simulator menu screen. To get to the GPS Simulator: 1. Press MENU | MENU | ↓ to GPS S ETUP | ENT . 2. Press ↓ to GPS S IMULATOR | ENT . The GPS Simulator Menu appears. GPS Setup Menu (left). GPS Simulator menu (center). M[...]

140 tion begins. Press EXIT to clear the alarm.) When navigation starts, press ↑ to increase speed to the desired setting. 4. Press EXIT to turn off the steering and speed boxes. The unit will now automatically steer along the trail or route. When you arrive at your destination, cancel navigation. Tip: You can pick any spot on the map to begin a [...]

141 Map Auto Zoom This receiver has an auto zoom feature that eliminates a lot of the but- ton pushing common with other brands of GPS receivers. It works in conjunction with the navigation features. Start navigating to a waypoint. Then, with the auto zoom mode on, the unit zooms out until the entire course shows, from the present position to the d[...]

142 Pop-up Map Information From the Map Data menu, highlight P OPUP M AP I NFORMATION and press ENT to turn it on (check) or turn it off (uncheck). After the option is set, press EXIT . Draw Map Boundaries From the Map Data menu, highlight D RAW M AP B OUNDARIES and press ENT to turn it on (check) or turn it off (uncheck). After the option is set, [...]

143 All datums have a name. The GPS system is based on the WGS-84 da- tum, which covers the entire world. Other datums may cover the entire world or just a small portion of it. By default, your position is shown with the WGS-84 datum. It, however, can show your position using any of 191 different datums. To change the Datum: 1. Press MENU | MENU | [...]

144 Map Menu (left). Map Categories Drawn Menu (right). To get to Map Categories Drawn: 1. From the Map Page, press MENU | ↓ to M AP C ATEGORIES D RAWN | ENT . 2. Scroll through the list of categories. Press ENT to turn on (check) or turn off (uncheck) a category. When a category is on, press → to jump to the subcategory window. Press ENT to tu[...]

145 To correct this problem track-up mode rotates the map as you turn. So what you see on the left side of the screen should always be to your left and so on. Another option is course-up mode, which keeps the map at the same orientation as the initial bearing to the waypoint. When either track-up or course-up modes are on, an "N" shows on[...]

146 NauticPath chart showing Chart Note icon selected by cursor (left). Note information screen (right). To view Chart Note information: 1. Use the arrow keys to move the cursor over a Chart Note icon. When it's selected, a pop-up name box appears. 2. Press WPT to display the Note Information screen. 3. To scroll through the Chart Note screen,[...]

147 To view Port Services information: 1. Use the arrow keys to move the cursor over a Port Services icon. When it is selected, a pop-up name box appears. 2. Press WPT to display the Port Services Information screen. NauticPath chart showing Port Services icon selected by cursor. When first highlighted, the Pop-Up name box appears. The Port Service[...]

148 zoomed in to a 6-mile range. The icon stands for a Tidal Current Sta- tion location. An example is displayed on the right. When you zoom in to a sufficiently small zoom range (0.8 nautical mile), the icon becomes an animated arrow showing tidal current ve- locity and direction for the selected tidal station at the present time. At larger zoom r[...]

149 The Tidal Current Information screen displays daily tidal current data for this station on this date at the present time. The graph at the top of the screen is an approximate view of the flood and ebb pattern for the day, from midnight (MN), to noon (NN) to midnight (MN). The velocity scale at the top left side of the graph changes dynamically [...]

150 To view tide information: 1. Use the arrow keys to move the cursor over a tide station icon. When it is selected, a pop-up name box appears. 2. Press WPT to display the Tide Information screen. Tide Information screen. The Tide Information screen displays daily tidal data for this station on this date at the present time. The graph at the top o[...]

151 inserted into the unit. Navionics charts must be inserted into the unit, then selected as a Map Choice option in the Map Data menu. To display a Navionics chart: 1. Install the Navionics MMC in the memory card compartment and turn on the unit. (For full card install instructions, see Sec. 2.) 2. From the Map Page, press MENU | ↓ to M AP D ATA[...]

152 System Setup Menu (left) with Pop-up Help highlighted. Pop-up Help message for the Map Data (right). Reset Options To reset unit to factory defaults: 1. Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT | ↓ to R ESET O PTIONS | ENT | ← to Y ES | ENT . NOTE: Reset Options does not erase any waypoints, routes, icons, plot trails or sonar logs. [...]

153 To Require WAAS: 1. Press MENU | MENU | ↓ to GPS S ETUP | ENT | ↓ to R EQUIRE WAAS | ENT . 2. To return to the main page display, press EXIT | EXIT . 3. Repeat Step 1 to turn off WAAS requirement. Require WAAS command on GPS Setup Menu. Screen Contrast and Brightness To access the Screen menu, press MENU | MENU | ENT . The C ONTRAST slider [...]

154 Set Language This unit's menus are available in 10 languages: English, French, Ger- man, Spanish, Italian, Danish, Swedish, Russian, Dutch and Finnish. To select a different language: 1. Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT . 2. Press ↓ to S ET L ANGUAGE | ENT . 3. Use ↓ ↑ to select a different language and press ENT . Men[...]

155 oping the WAAS system, it is not unusual for a GPS/WAAS receiver to frequently lose and reacquire its lock on a WAAS satellite. That can result in the alarm repeatedly going off. If you want, turn off the WAAS Acquired/Lost alarm without affecting how the unit uses WAAS. To turn off WAAS alarm: 1. Press MENU | MENU | ↓ to GPS S ETUP | ENT | ?[...]

156 Sounds highlighted on main menu (left). Sounds menu (right). Sounds Menu To adjust Sounds and Alarm Styles: Press MENU | MENU | ↓ to S OUNDS | ENT . To set Key Press Sounds: Press ENT to turn them on (check) or turn them off (uncheck). To set Alarm Sounds: Press ↓ to A LARM S OUNDS . With the option high- lighted, press ENT to turn them on [...]

157 Track Smoothing option, turned on. Trail Options There are several options you can use with trails. Some affect all trails, others can be applied to a particular trail. You can change the way trails are updated, display or hide trails, create a new trail, delete a trail, etc. Main Menu (left). Trails Menu (center). Trail Options (right). Genera[...]

158 WARNING: If you uncheck the Update Trail option, automatic trail creation and recording will be turned off . You must turn it on to record trails. The default setting is on. Update Trail Criteria The options are automatic, time or distance. When it is in the default mode, the unit does not update the plot trail while you are traveling in a stra[...]

159 Trail Name highlighted (left). Edit Trail menu (center). Trails menu with New Trail highlighted (right). Specific Trail Options Delete Trail From the Trails Menu, press ↓ to trail name | ENT . The Edit Trail menu appears. Press → to D ELETE T RAIL | ENT | ← to Y ES | ENT . New Trail To manually start a new trail, in the Trails Menu, highl[...]

160 the screen's display while working with a menu. A low transparency usually will make menu text easier to read, at the cost of watching your display. To adjust Transparency level: Press MENU | MENU | ↓ to T RANSPARENCY | ENT . The T RANSPARENCY slider bar appears. Press ↑ ↓ to adjust the level of transparency. Press EXIT when it is se[...]

161 Section 9: Searching NOTE: The background map loaded in your unit lets you search for U.S. Interstate Highway exits and exit services, as well as some land features, including cities and lakes. For a full set of searchable land features, including landmarks, streets, addresses and Points of In- terest, you must load your own high-detail custom [...]

162 In search results, the distance and bearing to the selected item will be calculated from the current position. In the case of a cursor search, the search results show distance and bearing from the cursor. Find Addresses 1. From the Map Page, press MENU | ↓ to F IND A DDRESS | ENT . 2. Press ENT to search in the Address field. 3. To enter an a[...]

163 NOTE: We recommend you do not enter a city name unless the list you are given is too large when searching without it. This unit can actually search quicker without a city and you save time by not entering a city name. Find City field (left). Search in particular city only option (center). Find City by name (right). 6. When the necessary search [...]

164 8. To navigate to the address, press MENU select G O T O and press ENT . The unit will begin showing navigation information to the address. If you are only looking up an address, highlight F IND and press ENT . The map page will appear with the cursor crosshairs centered on the ad- dress. Tip: If the address happens to be an item in the Point o[...]

165 A POI selected by the cursor (left). POI information screen (right). NOTE: Since the Go To waypoint command is highlighted, you can navi- gate to the selected POI by pressing ENT | EXIT while in the POI Waypoint Information screen. Find Interstate Highway Exits 1. From the Map Page, press MENU | ↓ to H IGHWAY E XITS | ENT , which will launch [...]

166 Find By Name menu (left). Find Exit menu with exit selected (right). 3. Once you have selected a highway name you can select an exit. Press ↓ to switch to the Exit List, then press ↓ ↑ until you highlight the exit, then press ENT. 4. In the Exit Information screen you have two choices. A. Press ENT | ENT to navigate or go to the exit. B. [...]

167 Exit Information screen (left). General location and amenities information (right). Find Map Places or Points of Interest (POI) 1. Press WPT , use ↓ ↑ to select a map place or POI category, then press ENT . (To narrow your search, press → to select a subcategory before pressing ENT .) You will be given two options: search by Name or by Ne[...]

168 Find by nearest option (left) with resulting POI list (right). 3. Search by name of POI. Highlight N AME and press ENT . There are two options: A. You can spell out the POI name in the top selection box. Press ↑ ↓ to change the first letter, then press → to move the cursor to the next letter and repeat until the name is correct, then pres[...]

169 Go To POI option (left). Find on Map POI option (right). Find Streets or Intersections Find a Street 1. From the Map Page, press MENU | ↓ to F IND S TREETS | ENT and the Find Streets Menu appears. Find Streets command (left). Find Streets menu (right). 2. You must enter a street name in the First Street dialog box. Press ENT to display the Fi[...]

170 The Find Streets menu with the Find First Street command high- lighted (left). Streets Found list (center). Map Page showing results of a street search (right). The cursor points to the located street. 3. The Find Streets menu reappears with the street you are searching for in the First Street box. To search for that street, press ↓ to F IND [...]

171 ENT | ENT . B. Or you can jump down to the lower box and pick the sec- ond street from the selection list. Press ENT , then press ↓ ↑ to select a street from the list and press ENT . 5. The Find Streets menu reappears with the first and second street dialog boxes filled in. You could now use similar techniques to select a city or Zip code, [...]

172 If you want to navigate to the found intersection, just press MENU | ENT | EXIT . Find Waypoints 1. Press WPT | ↑ to M Y W AYPOINTS | ENT . 2. If searching for the nearest waypoint, select N EAREST and press ENT . If searching by name, highlight N AME and press ENT . (To search by name, jump to step 5.) Find By Nearest command (left). Find by[...]

173 Find By Name menu (left). Waypoint Information screen (center). The cursor crosshairs are centered on the desired waypoint (right). A. To navigate to the waypoint, press ENT . The Go To Waypoint command is already highlighted. The unit will show navigation in- formation to the waypoint. B. To find the waypoint, press ↓ to F IND O N M AP | ENT[...]

174 Notes[...]

175 Section 10: Supplemental Material Datums Used by This Unit WGS 1984 Default Adindan Mean for Ethiopia, Sudan Adindan Burkina Faso Adindan Cameroon Adindan Ethiopia Adindan Mali Adindan Senegal Adindan Sudan Afgooye Somalia Ain el Abd 1970 Bahrain Ain el Abd 1970 Saudi Arabia Anna 1 Astro 1965 Cocos Islands Antigua Island Astro 1943; Antigua (Le[...]

176 Chua Astro Paraguay Corrego Alegre Brazil Dabola Guinea Djakarta (Batavia) Indonesia (Sumatra) DOS 1968 New Georgia Islands (Gizo Island) Easter Island 1967 Easter Island European 1950 Mean for Austria, Belgium, Denmark, Finland, France, West Germany, Gi- braltar, Greece, Italy, Luxembourg, Neth- erlands, Norway, Portugal, Spain, Sweden, Switze[...]

177 Naparima BWI Trinidad & Tobago North American 1927 Mean for Antigua, Barbados, Barbuda, Caicos Islands, Cuba, Dominican Republic, Grand Cayman, Jamaica, Turks Islands North American 1927 Mean for Belize, Costa Rica, El Sal- vador, Guatemala, Honduras, Nicaragua North American 1927 Mean for Canada North American 1927 Mean for CONUS (Continen[...]

178 Point 58 Sweden Santo (DOS) 1965 Espirito Santo Island Sao Braz Azores (Sao Miguel, Santa Maria Islands) Sapper Hill 1943 East Falkland Island Schwarzeck Nambia Selvagem Grande Salvage Islands SGS 85 Soviet Geodetic System 1985 South American 1969 Mean for Argentina, Bolivia, Brazil, Chile, Colombia, Ecuador, Guyana, Paraguay, Peru, Trinidad &a[...]

179 FCC Compliance This device complies with Part 15 of the U.S. Federal Communi- cations Commission (FCC) Rules. Operation is subject to the fol- lowing two conditions: (1) this device may not cause harmful in- terference, and (2) this device must accept any interference re- ceived, including interference that may cause undesired opera- tion. Chan[...]

180 Notes[...]

181 Notes[...]

182 Notes[...]

183 EAGLE DATABASES LICENSE AGREEMENT THIS IS A LEGAL AGREEMENT BETWEEN THE END-USER WHO FIRST PURCHASES THIS PRODUCT AS A CONSUMER ITEM FOR PERSONAL, FAMILY, OR HOUSEHOLD USE ("YOU") AND EAGLE ELECTRONICS, INC., THE MANUFACTURER OF THIS PRODUCT ("WE", "OUR", OR "US"). USING THE PRODUCT ACCOMPANIED BY THIS LI[...]

184 DATABASES LIMITED WARRANTY "We", "our", or "us" refers to Eagle Electronics, Inc., the manufacturer of this product. "You" or "your" refers to the first person who purchases the product as a consumer item for personal, family, or household use. The Databases Limited Warranty applies to the one o[...]

185 EAGLE ELECTRONICS FULL ONE-YEAR WARRANTY "We," "our," or "us" refers to EAGLE ELECTRONICS, INC., the manufacturer of this product. "You" or "your" refers to the first person who purchases this product as a con- sumer item for personal, family or household use. We warrant this product against def[...]

186 How to Obtain Service… …in the USA: We back your investment in quality products with quick, expert service and genuine Eagle parts. If you're in the United States and you have technical, return or repair questions, please contact the Factory Cus- tomer Service Department. Before any product can be returned, you must call customer servi[...]

Accessory Ordering Information for all countries To order Eagle accessories such as power cables or transducers, please contact: 1) Your local marine dealer or consumer electronics store. Most quality dealers that handle marine electronic equipment or other consumer electronics should be able to assist you with these items. To locate an Eagle deale[...]

Visit our web site: www.eaglesonar.com Eagle Pub. 988-0143-871 © Copyright 2005 All Rights Reserved Printed in USA 121205 LEI-Eagle [...]