English dropdown-ico

Edelbrock 1585 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Edelbrock 1585, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Edelbrock 1585 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Edelbrock 1585. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Edelbrock 1585 should contain:
- informations concerning technical data of Edelbrock 1585
- name of the manufacturer and a year of construction of the Edelbrock 1585 item
- rules of operation, control and maintenance of the Edelbrock 1585 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Edelbrock 1585 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Edelbrock 1585, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Edelbrock service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Edelbrock 1585.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Edelbrock 1585 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    Edelbrock 4.6L Mustang GT Supercharger Part #1580 & #1585[...]

  • Page 2

    ©2009 Edelbrock Corporation Catalog #1580 Brochure #63-1580 Rev . 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 2 Edelbrock Corporation, 2700 California Street, T orrance , CA 90503 T oll-Free T ech Line: 1-800-416-8628 Office: 310-781-2222 T ech E-Mail: Edelbrock@Edelbrock.com T[...]

  • Page 3

    ©2009 Edelbrock Corporation Catalog #1580 Brochure #63-1580 Rev . 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 3 Due to the complexity of the Edelbrock E-Force Supercharging system, it is recommend tha t this system only be installed by a qualified professional with access to a [...]

  • Page 4

    ©2009 Edelbrock Corporation Catalog #1580 Brochure #63-1580 Rev . 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 4 INST ALLING A BOOST GAUGE OR PRESSURE TRANSDUCER Y our E-Force supercharger is equipped with two options for measuring boost. The TMAP sensor mounted on top of the ma[...]

  • Page 5

    ©2009 Edelbrock Corporation Catalog #1580 Brochure #63-1580 Rev . 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 5 I. Hood Removal 1. Use a panel puller to pr y off two of the push-pins holding the hood insulator in place on the passenger side, then reach behind the insulator to d[...]

  • Page 6

    ©2009 Edelbrock Corporation Catalog #1580 Brochure #63-1580 Rev . 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 6 7. Use a 10mm socket with a 12” extension bar to remove the three bolts holding the batter y tray in place, then use a panel puller to detach the wiring harness cli[...]

  • Page 7

    ©2009 Edelbrock Corporation Catalog #1580 Brochure #63-1580 Rev . 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 7 11. Detach the mass airflo w sensor electrical connector from the air filter outlet tube. 12. Disconnect the eva porative emissions tube from the intake manifold and [...]

  • Page 8

    ©2009 Edelbrock Corporation Catalog #1580 Brochure #63-1580 Rev . 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 8 18. Remove the fuel line lock clip and let it dangle. 19. Use a 5/8” fuel line removal tool to disconnect the fuel supply line from the fuel rails. Use a shop ra g [...]

  • Page 9

    ©2009 Edelbrock Corporation Catalog #1580 Brochure #63-1580 Rev . 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 9 25. 2005-2008 a pplications should remove the o-ring seals from the intake manifold and inspect them for damage. Any damaged seals must be replaced; the rest will be [...]

  • Page 10

    ©2009 Edelbrock Corporation Catalog #1580 Brochure #63-1580 Rev . 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 10 31. Use a 10mm socket to remove the two outer alternator bracket bolts, and an 8mm socket to remove the two inner alternator bracket bolts. 8mm 10mm 32. Use a panel [...]

  • Page 11

    ©2009 Edelbrock Corporation Catalog #1580 Brochure #63-1580 Rev . 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 11 37. Reach through the fender well with a 10mm socket to loosen the two nuts on each side that attach the front bumper cover to the body . 38. Pull the front bumper c[...]

  • Page 12

    ©2009 Edelbrock Corporation Catalog #1580 Brochure #63-1580 Rev . 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 12 42. Use large pliers or a clamp removal tool to detach both upper radiator hoses from the water crossover . 43. Place shop ra gs in the engine valley to catch excess[...]

  • Page 13

    55. Hang the wa ter pump on the passenger side outer bumper bolts while pushing the outlet hose onto the inlet nipple of the heat exchanger . Secure the hose with a clamp, and the wa ter pump bracket with two of the M8 flange nuts supplied. 56. Install the long 3/4” hose onto the driver side barb of the heat exchanger and secure it with a clamp. [...]

  • Page 14

    ©2009 Edelbrock Corporation Catalog #1580 Brochure #63-1580 Rev . 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 14 59. ‘05 a pplications should locate the red wire in pin 10, near the bottom of the connector . ‘06 a pplications should locate the red wire in pin 2, a t the top[...]

  • Page 15

    70. Detach ETC connector from supplied ETC extension harness and raise wedge lock. Insert the red wire with the yellow stripe into Pin 1 of the new ETC connector by aligning the slot on the wire terminal with the tab in the connector and pushing gently until it clicks into place, then insert the blue wire with the yellow stripe into Pin 2 and seat [...]

  • Page 16

    80. Loca te the electrical connector on the main harness previously occupied by the alternator control wiring harness. Attach the round alterna tor connector on the supplied TPS/Alternator harness into this connector and route the harness around the back of the engine bay , then forward along the driver side cylinder head. 81. Loca te the MAF senso[...]

  • Page 17

    VIII. Cooling System Modifications 89. Route the molded hose under the fuse box and onto the inlet at the top of the water pump. Secure it with a clamp. 90. Remove the two inner passenger side strut to wer nuts and hang the recovery tank bracket from the exposed bolts. Do not reinstall strut nuts a t this time. 91. Slide the molded hose onto the bo[...]

  • Page 18

    99. Once the coolant pipes ha ve been separated, reinstall the smaller diameter of the two by gently sliding it onto the nipple in the engine valley and securing it onto the back of the head with the stock bolt. The lo wer hose and larger diameter hard line can be discarded. 100. Rea ttach the upper heater hose to the hard line with the stock hose [...]

  • Page 19

    104. Use a 13mm socket to remove the two upper driver side front cover bolts, and an 18mm socket to remove the bottom driver side bolt, as shown belo w . 105. Slide the larger of the two Edelbrock supplied idler pulleys onto the lower idler boss of the front cover with the open side facing the engine block. 106. Use a 12mm deep socket and a small a[...]

  • Page 20

    XI. Installing the Supercharger 112. Install the Edelbrock supplied hea ter hose on the firewall connector , and lay it to the side for now. 113. Remove the supercharger assembly from its packing container and install the o-ring seals, removed from the stock manifold on early applications and supplied in the #15805 Hardware Kit for 2009 application[...]

  • Page 21

    120. Use a 10 mm socket to install the supplied intake bolts, and torque them to 8 ft/lbs in the sequence shown. 121. Install the new fuel injectors (not included in 1585) into the stock fuel rails by applying a bit of o-ring lube to both o-rings of each injector , sliding the stock retaining clips onto the injectors, then pushing each injector int[...]

  • Page 22

    126. Connect the EVAP hose to the hard line at the front of the manifold. 127. Reconnect the fuel pressure sensor to the main wiring harness. Be sure to use the connector tha t does not have a red locking tab, the connector with a red locking tab is for the TPS. 128. Plug wiring harness extension into TMAP sensor . XII. Modifying Stock Components 1[...]

  • Page 23

    134. Use a fla t head screwdriver to pop off the bearing cover on the alternator pulley . ‘05-’08 applications should use the supplied tool with an impact wrench to remove the stock pulley . ‘09 and later a pplications should use a 24mm allen tool with an impact wrench. 135. Install the new alterna tor pulley with the nut supplied in hardware[...]

  • Page 24

    140. Route the supplied serpentine belt according to the diagram provided below by using a 1/2” breaker bar to twist the belt tensioner enough to allow the belt to slide into place. XIII. Installing the Throttle Body 141. Use 8mm and 10mm sockets to unbolt the OEM throttle body from the stock intake manifold, using care not to damage the motor ho[...]

  • Page 25

    147. Reinstall the motor housing ca p by lining up the tabs and applying light pressure. 148. Reuse the stock bolts to install the TPS on the new throttle body by lining up the locating tab and pushing it straight on. Be careful to a void rotating the TPS during installation. 149. Verify correct installation by pushing the butterfly open and closed[...]

  • Page 26

    152. Install the new high flo w air filter in the airbox. 153. Use a T20 T orx driver to install the new MAF sensor in the air cover outlet tube, torque the two screws that retain it to 18 in/lbs., then reinstall the cover . 154. Install the throttle bod y elbow onto the throttle body and secure it with the provided hose clamps. The flexible elbow [...]

  • Page 27

    ©2009 Edelbrock Corporation Catalog #1580 Brochure #63-1580 Rev . 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 27 160. Install the supplied hea ter hose onto the heater tube on the passenger side of the water crossover . 161. Verify that the coolant petcock is closed, then refil[...]

  • Page 28

    174. Verify that wa ter is flowing briskly through the recovery tank, then install the cap. 175. Ha ve an assistant support the hood while you tighten the four bolts that secure it to its hinges. Be careful to verify that it is properly aligned and that the supercharger has nothing on top of it before you attempt to close the hood. 176. Rea ttach t[...]

  • Page 29

    ©2009 Edelbrock Corporation Catalog #1580 Brochure #63-1580 Rev . 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 29 179. Read the discalimer carefully , then choose ‘Agree’ and press select. 180. Use the arro w buttons to select your transmission, then press select to confirm [...]