Go to page of
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of Epson 36-714, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Epson 36-714 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of Epson 36-714. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of Epson 36-714 should contain:
- informations concerning technical data of Epson 36-714
- name of the manufacturer and a year of construction of the Epson 36-714 item
- rules of operation, control and maintenance of the Epson 36-714 item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Epson 36-714 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Epson 36-714, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Epson service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Epson 36-714.
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the Epson 36-714 item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
-
Page 1
INSTRUCTION MANUAL Delta 10" Hybrid Saw (Model 36-714) P ART NO. A08139 - 06-14-05 Copyright © 2005 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). NOTE: Shown with BC30 30” [...]
-
Page 2
2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could r esult in serious injury and prop[...]
-
Page 3
3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf[...]
-
Page 4
4 GENERAL SAFETY RULES READ AND UNDERST AND ALL W ARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage. IMPORT ANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA[...]
-
Page 5
5 F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . ADDITIONAL SPECIFIC SAFETY RULES 1 . DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions. 2. OBT AIN ADVICE FROM YOUR SUPERVISOR, instructor , or another qualified person if you are not familiar with the operation of this machine. [...]
-
Page 6
6 6 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug. Before conn[...]
-
Page 7
EXTENSION CORDS Use proper extension cor ds. Make sure your extension cor d is in good condition and is a 3-wire extension cord which has a 3-pr ong grounding type plug and matching r eceptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine. An undersized c[...]
-
Page 8
CAR TON CONTENTS Fig. 1 Parts 1. Cast Iron Extension Wings (2) 2. Switch Assembly 3. Fence Holder Brackets (2) 4. Drive Belt 5. T able Insert 6. Wr ench Hook 7. Miter Gage Holder 8. Splitter Mounting Bracket 9. Blade Hex Nut 10. Blade Flange 11. 10” Carbide- Tipped Blade 12. Blade W renches (2) 13. 4mm Hex Wr ench 14. Dust Port 15. Locking Knobs [...]
-
Page 9
9 UNP ACKING AND CLEANING Carefully unpack the machine and all loose items fr om the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be r emoved with a soft cloth moistened with kerosene (do not us e acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surface[...]
-
Page 10
10 Fig. 4 DISCONNECT MACHINE FROM POWER SOURCE. T o bolt the saw to a permanent location, remove the nine screws which secur e the dust chute inside the saw cabinet, six of which are shown at (C) Fig. 4. Also, remove the side panel below the motor cover by loosening all six screws (D). Find the holes (E) Fig. 5 in the bottom of the saw and mark the[...]
-
Page 11
DISCONNECT MACHINE FROM POWER SOURCE. First, lift motor and remove foam packing block fr om around motor . While lifting motor (A) Fig. 8, place a 10-12 inch long piece of 2x4, or another similar thickness of wood, (B) Fig. 8 as shown. This will help prop up the motor and will make it easier to install the grooved belt, (C) Fig. 8A. Place grooved b[...]
-
Page 12
12 Fig. 10 DISCONNECT MACHINE FROM POWER SOURCE. Assemble left extension wing (A) Fig. 10A to the saw table. Align the three holes in the extension wing with the three holes (A) Fig. 9 in the side of the saw table. Place a 7/16" lockwasher , then a 7/16" flat washer on a 7/16- 20x1-1/4” hex head screw (all shown at (B) Fig. 9). In ser t[...]
-
Page 13
13 INST ALLING THE SWITCH DISCONNECT MACHINE FROM POWER SOURCE. 1. Place switch (A) Fig. 11, behind the lip of extension wing (B). Insert M8x30 hex head screw (C) thr ough wing and then switch support. Place an M8 flat washer and an M8 lock washer on the screw . Thread an M8 hex nut (D) onto screw and tighten nut secur ely . 2. Insert switch cord w[...]
-
Page 14
14 ASSEMBLING BLADE GUARD AND SPLITTER ASSEMBL Y DISCONNECT MACHINE FROM POWER SOURCE . MAKE SURE BLADE IS NOT A TT ACHED. IF IT IS, REMOVE THE SAW BLADE FROM THE SA W USING THE SUPPLIED WRENCHES. 1. Fasten the r ear splitter mounting bracket (A) Fig. 15, to the rear trunnion on the back of the saw using the two 1/4”-20 x 3/4 ″ hex head screws [...]
-
Page 15
15 5. If alignment is necessary , loosen the two screws (F) Fig. 18, align bracket (D) with the inner arbor flange (E), and tighten screws (F). 6. Loosely assemble large washer and scr ew (C) Fig. 18, to the inside splitter bracket. This screw and washer was removed in STEP 3 . 7. Assemble the blade guar d and splitter assembly (G) Fig. 19 between [...]
-
Page 16
16 SAW BLADE DISCONNECT MACHINE FROM POWER SOURCE. 1. Raise the saw blade arbor to its maximum height. Assemble the saw blade (C) Fig. 23 to the saw arbor making sure the teeth of the blade point down towards the fr ont of the table, as shown in Fig. 23. Assemble the flange (D) and arbor nut (E) to the saw arbor and tighten arbor nut (E) as far as [...]
-
Page 17
17 Fig. 26 L P INST ALLING T ABLE INSER T DISCONNECT MACHINE FROM POWER SOURCE. Lower saw blade and install table insert (P) Fig. 26, in the saw table. IMPORT ANT : When installing the table insert, make certain to hold on to the blade guard (L). The insert will automatically release the holding action on the splitter and lower the blade guard when[...]
-
Page 18
18 ASSEMBLING MITER GAGE DISCONNECT MACHINE FROM POWER SOURCE Place a flat washer (A) Fig 30 on the threads of the miter gage lock handle (B) and then thread the handle into the hole (C) in miter gage bar . Insert plate (D) Fig.41 into the miter gage slot (E) Fig. 41 and slide miter gage onto saw table. Fig. 30 OPERA TION ST AR TING AND STOPPING SA[...]
-
Page 19
19 Fig. 33 C Fig. 34 E D ADJUSTING 90 DEGREE AND 45 DEGREE POSITIVE STOPS The machine is equipped with positive stops that will quickly and accurately position the saw blade at 90° and 45° to the table. T o check and adjust the positive stops, proceed as follows: DISCONNECT MACHINE FROM POWER SOURCE. 1. Remove the blade guard and splitter . 2. Ra[...]
-
Page 20
20 Fig. 38 A B D C BACKLASH ADJUSTMENTS DISCONNECT MACHINE FROM POWER SOURCE. After a period of extended use, if any play is detected in the blade raising or blade tilting mechanisms, remove the blade and make the following adjustments: ADJUSTING BLADE RAISING MECHANISM - Loosen locknut (A) Fig. 38, and turn eccentric sleeve (B) until all play is r[...]
-
Page 21
21 MITER GAGE OPERA TION AND ADJUSTMENT The miter gage is equipped with adjustable index stops at 90, 75, 60,45 and 30 degrees. T o rotate the miter gage, loosen lock knob (A) Fig. 40, push the thumb lever (B) down and move the body of the miter gage (C) to the desired angle. The miter gage is equipped with a plate (D) Fig.41 which fits into the T [...]
-
Page 22
22 CROSS-CUTTING Cross-cutting r equires the use of the miter gage to position and guide the work. Place the work against the miter gage and advance both the gage and work toward the saw blade, as shown in Fig. 42. The miter gage may be used in either table slot. When bevel cutting (blade tilted), use the table groove that does not cause interferen[...]
-
Page 23
23 Ripping is cutting lengthwise through a boar d, (Fig. 45). NOTE : Be sure the material to be cut is seasoned, dry and flat. The rip fence (A) is used to position and guide the work. One edge of the work rides against the rip fence while the flat side of the board r ests on the table. Since the work is pushed along the fence, it must have a strai[...]
-
Page 24
24 Fig. 49 Fig. 51 Fig. 50 H G USING MOULDING CUTTERHEAD Moulding is cutting a shape on the edge or face of the work. Cutting mouldings with a moulding cutterhead is a fast, safe and clean operation.The many differ ent knife shapes available make it possible for the operator to produce almost any kind of mouldings, such as various styles of corner [...]
-
Page 25
25 Fig. 56 Fig. 54 Fig. 55 Fig. 53 1. Dadoing is cutting a rabbet or wide groove into the work. Most dado head sets are made up of two outside saws and four or five inside cutters, (Fig. 53). V arious combinations of saws and cutters are used to cut grooves fr om 1/8 ″ to 13/16 ″ for use in shelving, making joints, tenoning, grooving, etc. The [...]
-
Page 26
26 TROUBLESHOOTING For assistance with your machine, visit our website at www .deltamachinery .com for a list of service centers or call the DEL T A Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582). Fig. 59, illustrates dimensions for making a typical featherboard. The material which the featherboar d is constructed of, should [...]
-
Page 27
27 When ripping work less than 4 inches wide, a push stick should be used to complete the feed and could easily be made from scrap material by following the pattern shown in Fig. 78. Fig. 78 PUSH STICK MAKE FROM 1/2 " OR 3/4 " WOOD OR THICKNESS LESS THAN WIDTH OF MA TERIAL TO BE CUT CUT OFF HERE TO PUSH 1/4 " WOOD CUT OFF HERE TO PUS[...]
-
Page 28
28 P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations. T o obtain additional information regar ding your Delta quality product or to obtain parts, service, warra[...]
-
Page 29
29 A complete line of accessories is available from your Delta Supplier , Porter -Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our W eb Site www .deltamachinery .com for a catalog or for the name of your nearest supplier . Since accessories other than those offer ed by Delta have not been tested with [...]
-
Page 30
30 NOTES[...]
-
Page 31
31 NOTES[...]
-
Page 32
The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T[...]