Epson 820 manual

1
2
3
4
5

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Epson 820, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Epson 820 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Epson 820. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Epson 820 should contain:
- informations concerning technical data of Epson 820
- name of the manufacturer and a year of construction of the Epson 820 item
- rules of operation, control and maintenance of the Epson 820 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Epson 820 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Epson 820, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Epson service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Epson 820.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Epson 820 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    820 CFS Installation Instructions Pre-Filled CFS Below are the instructions for installing a pre-filled CFS for an Epson 820 printer. Here is what you will need to do this installation….. • Alcohol or Alcohol swabs • Continuous Flow Cartridge set with Tubes attached • (2) MIS Short Bracket and (1) MIS Bridge Bracket for 820/C60 Printers •[...]

  • Page 2

    Cartridge Installation 4. Check the CFS cartridge, there should be 4 Velcro st rips on each cartrid ge. You may have to guide these pads into the cartridge holder, it is a tight fit. Push the cartridg e all the way down, so printer po sts puncture the seals on the bottom of the cartrid ge. Make sure th ey are down all the way an d are making contac[...]

  • Page 3

    Tubing Installation 8. Move the cartridges towards the left side of the printer, but don’t push them unde r the housing. Get the end of the tubing that you left hanging off the right side of the printer. Loop it back towards the left side of the printer, under the Bridge Bracket. Put alcohol on the tube clip on the undersi de of the bridge bracke[...]

  • Page 4

    Trim each tube length so that the tube will make a tu rn into the bottle without rising up. There must be 3 ¾ inch of tubing inside the bottle. When you cut the t ube, cut on a 45 degree angle so the end of the tube is pointed. After you cut the tubes to length, use a black marker and make a mark on each tube 3 ¾ inch from the end of the tube. In[...]

  • Page 5

    If you purchased your CFS unit before 4/28/03, then it ship ped with an F-1 6 chip resetter. After 4/28, the F-16 was replaced by Auto Reset chips. The F-16 will no t work with the Silver 820 printers, sometimes called the 820S. If you have an 820 with the silver housing and an F-16 Chip Resetter, give us a call. Using the Auto Reset Chips – The [...]