English dropdown-ico

EverFocus EZ650 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of EverFocus EZ650, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of EverFocus EZ650 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of EverFocus EZ650. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of EverFocus EZ650 should contain:
- informations concerning technical data of EverFocus EZ650
- name of the manufacturer and a year of construction of the EverFocus EZ650 item
- rules of operation, control and maintenance of the EverFocus EZ650 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of EverFocus EZ650 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of EverFocus EZ650, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the EverFocus service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of EverFocus EZ650.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the EverFocus EZ650 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    Operation Instruction I I R R D D a a y y / / N N i i g g h h t t p p l l u u s s W W i i d d e e D D y y n n a a m m i i c c R R a a n n g g e e I I P P 6 6 6 6 B B u u l l l l e e t t C C a a m m e e r r a a E E Z Z 6 6 5 5 0 0 EverFocus[...]

  • Page 2

    2 EVERFOCUS ELECTRONICS CORPORATION P/N: 4605XZ0650001AR Operation Instruction  20 08 EverFocus E lectronics Corp Please read this manual first for correct installation a nd operation. This manu al should be retained for future reference. The i nformation in this ma nual was current when pu blished. The man ufacturer reserves the right to revise[...]

  • Page 3

    3 Precautions 1. Do not place any object on top of the cover. 2. Be careful when handling the camera, do not drop it or subject it to strong shock or vibration to prevent any damages to it. Do not disass emble it or place it on an unstable base. 3. Install the camera away from TV, radio transmitter, magnet, elec tric motor, transformer, audio speak[...]

  • Page 4

    4 Federal Communication Commission Interference Statement This equipment has been tested and fou nd to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and ca[...]

  • Page 5

    5 Table of Contents 1.1 FEATUR ES .......................................................................................................................................... 6 1.2 ACCESSORY P ART S LIST ....................................................................................................... ....... 7 1.3 SPECIFICATI ONS ..............[...]

  • Page 6

    6 1. Product Overview Achieve long range surveillance with clarit y in virtually any lighting conditions. The amazing lo w light sensitivity of 0.05 lux before the added benefits of advanced DSP technology, delivered by a 1/3” Sony Super HAD CCD II sensor, is just the beginning with the new EverFocu s EZ650. A 6-50mm varifocal auto-iris lens comb[...]

  • Page 7

    7  Motion detection for 4 configurable zones.  Privacy mask function for 8 configurable zones.  Provides digital zoom up to 32x.  Cables routed through weatherproof bushing in the bracket to prevent vandalism or other damage.  IP66 weather resistant.  Operating temperature range -40°C to 50°C/ -40°F to 122°F, with thermostatic[...]

  • Page 8

    8 1.3 Specifica tions Product Model EZ650 Pickup Device 1/3” SONY Super HAD CCD Ⅱ Video Format NTSC or PAL Picture Elements 768 x 494 (NTSC)/752 x 582 (PAL) Horizontal Resolution 560 TV Lines Sensitivity 0.05Lux/F=1.2(AGC ON); 0.0002Lux/F=1.2 (IR off ,Sens-up 256x Max; ~8X recommened) 0 Lux (IR On) S/N Ratio Over 52dB (AGC off) Electronic Shutt[...]

  • Page 9

    9 1.4 Dimensions Drilling Dimension of holes to holes Dimension of Bracket 45mm/1.8” 80mm/3.2” 220.5mm/8.68” 84mm/3.31” 106.5mm/4.19 112.7mm/4.44 199mm/7.83”[...]

  • Page 10

    10 Dimension of whole camera with bracket Dimension of whole camer a with bracket and EPR100 275mm/10.8” 107.5mm/4.3” 243.5mm/9.74” 357mm/14”[...]

  • Page 11

    11 1.5 Camer a Component Description EZ650 Component description Bracket Sun shield Fixing screw for sunshield Video output Power connector RS485 terminal Control key selection switch Control key[...]

  • Page 12

    12 1.6 Bac k P anel Lay out 1. Video Output Connector Connect the video output of the camera to a co lor monitor or other video devices through a 75 Ohm type coaxial cable with BNC female connector at backside of the camera. 2. Power Input Terminal Connect the appropriate power to each model. N/ L is used to connect to power in. PE is a ground pin.[...]

  • Page 13

    13 5. Control key selection switch Switch to OSD to control OSD menu by using t he control key or switch to LENS to adjust zooming and focus (please see “2.3.1 Lens se tting” and “3. OSD Menu & Configuration” for details). Note : when it is connected to RS485 for keyboard cont rol, please switch to OSD, otherwise it cannot be controlled[...]

  • Page 14

    13 2. Installation This chapter will describe, in general terms, how to install the EZ650 camera. STEPS: 1. Wire and mount the camera. See 2.1 2. Adjust the camera position. See 2.2 3. Adjust Lens. See 2.3 4. Connect to Keyboard (Optional) See 2.4 Warning  To prevent electrical shock, turn off the electrical power before making electrical connec[...]

  • Page 15

    14 2. Fix the bracket to wall by using 4 screws. 3. Open camera’s back cover: Loose the 2 screw s from the back panel cover , then open the back cover . Screws for back panel Coaxial cable Power cable RS485 cable[...]

  • Page 16

    15 4. T ake off the cap of waterproof condui t which is at the camera bottom. Note: 1. the holes of waterproof conduit were plugged, please remove the plug when you need to use it for connection. 5. T ake coaxial cable, power cable and RS485 cable to pass through waterproof conduit, place them into camera housing. Note: Do not connect BNC connector[...]

  • Page 17

    16 Note: 1. Power cable’s diameter must be less than 10 mm 2. Only use RG59/5C2V for Video cable 3. RS485 cable must be less then 5 mm 6. Close the waterproof cap and fix waterp roof conduit to the base of camera firmly . 7. Fix the camera body to bracket by using the 4 shorter screws. Coaxial cable Power cable RS485 cable[...]

  • Page 18

    17 8. Connect RG59 coaxial cable with BNC connector . 9. Unscrew both cable clips, wire power cable and RS485 cable through t he cable clips. Then, screw the cable clips to rear panel. a. Connecting Power-24V AC model: connect 24VAC power on N and L 100V AC~240V AC Model: Connect PE, N and L. *W arning*  To prevent electrical shock, turn off t h[...]

  • Page 19

    18 2.2 Adjusting Camer a P osition Adjust camera’s angle vertically or horizon tally by using hex key included in package. Screws for back panel Loose this screw to make angle adjustment vertically Loose this screw to make angle adjustment horizontally[...]

  • Page 20

    19 2.3 Adjusting Lens Open camera’s base, a control key is attached at inner side of the base. Detach the control key and use this key for OSD or Lens setting. 2.3.1 Lens Setting Please turn the control key selection switch at the back panel to “ Lens ”.( ). Use the control key to do lens setting. Turn the mini-joystick Up (  ) or Down ( ?[...]

  • Page 21

    20 2.4 K eyboar d Connection (Optional) Please refer to Chapter 4 for more details of Keyboard control. 1. Connect the cable from keyboard’s RS485 por t to camera’s RS485 port. (Keyboard is an optional accessory). RS485 connecting accesso ries are included in Everfocus Keyboard package. 2. Connect the cable from video output jack of the camera [...]

  • Page 22

    21 3. OSD Menu & Configuration This chapter introduces how to configure the camera OSD menu. 3.1 Contr ol K ey Gener al Operation Guide Please turn the control key selecti on switch at the back panel to “ OSD ” ”( ). Use the control key to do OSD menu setting. I. Bring Up the General OSD Menu Simply press the mini-joystick to bring up the[...]

  • Page 23

    22 When the item with sub-menu is selected, press the mini-joystick to sw itch to the sub-menu for further settings. Please refer to the diagram below. NOTE: For those selected items with “ ” sign in the end, they have the sub- menu for further settings. VI. Return to Previous Page Press the mini-joystick to return to previous page. VII. Close [...]

  • Page 24

    23 3.2 RS485 ID & Baud Ra te Setting Note : This section is optional pres erved for the people that want to change camera ID and baud rate. In most situations, we suggest you can just use Camera ID-01 and Baud Rate -9600, Protocol-Pelco D on keyboard, then it would work. I. Please turn the control key se lection switch at back panel to “ OSD [...]

  • Page 25

    24 b. RS485_ID- adjustable 01~128. De fault value is 01. Move joysti ck RIGHT and LEFT to adjust it. RS485 ID of EZ650 has to be th e same as Keyboard’s C AM ID. c. BAUD_RATE-adjustable 9600, 4800, 2400 and 1200. Default value is 9600. Move joystick RIGHT and LEFT to adjust it. Baud rate of EZ650 ha s to be the same as Keyboard’s baud rate. A B[...]

  • Page 26

    25 d. DATA STORED- Confirm with you that the last 3 settings you have made will be saved. e. ENTER_SET_MENU- press the mini-joy stick to enter OSD menu se tting. Note : For Camera Protocol, EZ650 recognizes EVF-1, EVF-2 and Pelco-D protocols automatically. (No setting is required) After setting, it will show an OSD menu, to save setting, go to exit[...]

  • Page 27

    26 3.3 OSD Menu Setup 3.3.1 OSD Menu T ree Default settings are shown bold or in brackets. Lens — DC — Brightness 0~100 (50) Exposure — Shutter — x256, x128, x64, x32, x16, x8, x 4, x2, 1/60(NTSC) / 1/50 (PAL) , FLK,1/250, 1/500, 1/1000, 1/2000, 1/5000, 1/10000 — AGC — HIGH ; MIDDLE ; L O W ; O F F — SENS-UP — AUTO (x8) ; OFF — BL[...]

  • Page 28

    27 — Motion — Off — On — Area Select — Area1-Area4 — Area Display — Off, On — Left/Right — 5~66 — Width — 0~93 — Top/Bottom — 1~60 — Height — 0~60 — Sensitivity — 0~40 — Motion View — Off, On — Return — Privacy — Off — On — Area Select — Area1-Area4 — Area Display — Off, On — Left/Right — 6~[...]

  • Page 29

    28 3.3.2 LENS When the SETUP menu is displayed on the screen, pleas e direct the arrow to point to “LENS” by using the UP and DOWN buttons. The iris opening can be adjusted in DC mode in LE NS LEVEL. The level can be adjusted from 0 to 50. Please select RETURN and press t he SETUP button if you would like to return to the previous menu. 3.3.3 E[...]

  • Page 30

    29 3.3.3.4 BLC-BACKLIG HT COMPENSATION There are three choices for the type of BLC which may be employed: OFF, traditional BLC or HSBLC. BLC Video gain can be adjusted automatica lly to correct the exposure of s ubjects that are in front of a bright light source. Please direct the arrow to point to “B LC” by using the UP and DOWN buttons. Selec[...]

  • Page 31

    30 1. Please direct the arrow to point to “BLC” by using the UP and DOWN buttons. 2. Select the HSBLC mode by pressing the LEFT or RIGHT butt on. Then make adjustments as below: LEVEL Adjust the sensitivity level for HSBLC from 0 to 8. DEFAULT Set the factory default values for HSBLC. LEFT/RIGHT Set the Left/Right side of an area for the HSBLC [...]

  • Page 32

    31 3.3.4 WHITE BALANCE CONTROL The screen color can be adjusted by using the WHITE BALANCE function. Please direct the arrow to point to “WHITE BAL” by using the UP and DOWN buttons. Please select the mode you would like to operate by pressing the LE FT or RIGHT button. Please select one of the 6 modes below: ATW Auto Tracking White Balance: Th[...]

  • Page 33

    32 Press “RET” to save all settings in the DAY/NIGHT menu and returns to the previous menu. Press “END” to save all the setting menus and exit. COLOR The picture is always displayed in color, even at low light levels. NOTE: In “color” operation, there is an IR “cut” (blocking) filter between the lens and the sensor; thus EZ650 camer[...]

  • Page 34

    33 Please direct the arrow to point to “CAM TITLE” by using the UP or DOWN button. Select “ON” by pressing the LEFT or RIGHT button. Press SETUP button. Maximum 15 characters can be used for the ID. Use UP, DOWN, LEFT and RIGHT buttons to move the cursor to the letter to be chosen. Use SETUP button to choose that letter. Once a name has bee[...]

  • Page 35

    34 3.3.7.5 D-ZOOM Setup for digital zoom. OFF Disable the D-ZOOM function ON D-Zoom: Select digital zoom from X1.0 up to X32. Note that zoom levels above X4 may lead to excessive pixellation. Setup of the position of the magnified image in view (0 is the center of the image): Pan: Select digital pan from -100 to 100. Tilt: Select digital tilt from [...]

  • Page 36

    35 the sensitivity value is high, motion det ection sensitivity increases to sense very small movements and vice versa. MOTION VIEW Select “ON” to display motion detection pixels in the live view. RETURN Press “RET” to save all settings in MOTION menu and return to the previous menu. Press “END” to save all the menu settings and exit. 3[...]

  • Page 37

    36 3.3.8.1 SHARPNESS The contour of the video image becomes cleaner and more easily distinguished as the level of SHARPNESS increases. If the leve l is set too high, it may a ffect the video image and cause noise. The available range of level is 0~31. 3.3.8.2 BLUE Adjust image’s blue level. The av ailable range of level is 0~100. 3.3.8.3 RED Adju[...]

  • Page 38

    37 Control from Keyboard EKB500 (Optional) Note! Before being able to control keyboard, make su re Keyboard RS485 camera ID, Baud rate match the camera. (see COM port setting in EKB500 m anual). EZ650 camera ID default is 01. Baud rate is 9600. Support Protocol EVF-1, EVF-2 and Pelco-D. 4.1 K ey F ea tur es with K eyboar d 1. OSD can be set up from[...]

  • Page 39

    38 d. Move the joystick RIGHT (  ) and LEFT (  ) to adjust the mode an d parameters of the selected item. e. Press “Menu” to leave and goes to previous menu after setting. Move to “exit” and press “menu” button when you finish all settings. f. For detail setting and every setup function, Please refer to “3.3. OSD Menu Setup”. [...]

  • Page 40

    39 EverFocus Electronics Corp. EverFocus Taiwan: 12F, No.79, Sec. 1, Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan TEL: +886 2 2698 2334 FAX: +886 2 2698 2380 www.everfocus.com.tw marketing@everfocus.com.tw EverFocus Europe - Germany: Albert-Einstein-Strasse 1, D-46446 Emmerich, Germany TEL: +49 2822 93940 FAX: +49 2822 939495 www.everfocus.de info@ev[...]