Ford 2000 Explorer manual

Before driving Introduction 2 Instrumentation 6 Controls and features 21 Seating and safety restraints 1 19 Starting and driving Starting 150 Driving 155 Roadside emergencies 189 Servicing Maintenance and care 212 Capacities and specifications 266 Customer assistance 275 Reporting safety defects 287 Index 288 All rights reserved. Reproduction by an[...]

The following warning may be required by California law: CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and [...]

BREAKING-IN YOUR VEHICLE There are no particular breaking-in rules for your vehicle. During the first 1 600 km (1 000 miles) of driving, vary speeds frequently . This is necessary to give the moving parts a chance to break in. INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the[...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation W arning Child Seat T ether Anchorage Brake System Anti-Lock Brake System Brake Fluid - Non-Petroleum Based T raction Control Master Lighting Switch Ha[...]

V ehicle Symbol Glossary Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Correct Fluid Level MAX MIN Emission System Engine A[...]

RSM SET ACCEL COAST OFF ON OD ON/OFF C 0 1 2 3 4 5 6 RPMx1000 ABS ! CHECK ENGINE FUEL RESET E F H H H SPEED CONT 4WD HIGH 4WD LOW O/D OFF L L DOOR AJAR CHECK GAGE CHECK SUSP VOL PUSH 1 10 MPH 20 50 60 70 30 40 80 90 km/h 0 0 0 10 1 00 1 20 1 0 0 0 0 0 0 40 60 80 100 120 140 160 180 20 OFF HIGH 4x4 LOW AUTO OFF Instrument cluster (pg. 8) Speed contr[...]

PUSH OFF HI R. WIPE OFF A/C MAX A/C SCAN BASS TREB BAL FADE SIDE EJ REW FF 1 - 2 TAPE AMS ON SEEK TUNE AM FM CLK 2 3 456 FM1 ST Electronic sound system (pg. 35) Rear window/washer control (pg. 88) Rear window defroster control (pg. 33) Climate controls (pg. 22) 4wd control* (pg. 168) Fog lamp control* (pg. 21) Instrumentation 7[...]

W ARNING LIGHTS AND CHIMES Check engine Y our vehicle is equipped with a computer that monitors the engine’ s emission control system. This system is commonly known as the On Board Diagnostics System (OBD II). This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards. The OBD II syst[...]

3. The fuel cap may not have been properly installed and securely tightened. These temporary malfunctions can be corrected by filling the fuel tank with high quality fuel of the recommended octane and/or properly installing and securely tightening the gas cap. After three driving cycles without these or any other temporary malfunctions present, the[...]

Air bag readiness Momentarily illuminates when the ignition is turned ON. If the light fails to illuminate, continues to flash or remains on, have the system serviced immediately . Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating [...]

T urn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the indicators stay on continuously or flash faster , check for a burned-out turn signal bulb. Refer to Bulbs in the Maintenance and care chapter . High beams Illuminates when the high beam headlamps are turned on. Anti-theft system (if[...]

Four wheel drive low (if equipped) Momentarily illuminates when the ignition is turned to the ON/ST ART position. Illuminates when four -wheel drive low is engaged. If the light continues to flash have the system serviced. Four wheel drive high (if equipped) Momentarily illuminates when the ignition is turned to the ST ART position. Illuminates whe[...]

Speed control This light comes on when either the SET/ACCEL or RESUME controls are pressed. It turns off when the speed control OFF control is pressed, the brake or clutch (if equipped) is applied or the ignition is turned to the OFF position. Safety belt warning chime Sounds to remind you to fasten your safety belts. For information on the safety [...]

GAUGES Speedometer Indicates the current vehicle speed. Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely p[...]

Never remove the coolant reservoir cap while the engine is running or hot. This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level the gauge indication will not be accurate. Odometer Registers the total kilometers (miles) of the vehicle. T rip odometer Registers the kilometers (mi[...]

Battery voltage gauge This shows the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range (as indicated), have the vehicle’ s electrical system checked as soon as possible. Engine oil pressure gauge This shows the engine oil pressure in the system. Sufficient pressure exists as[...]

The FUEL DOOR icon and arrow indicates which side of the vehicle the fuel filler door is located. MESSAGE CENTER (IF EQUIPPED) W ith the ignition in the ON position, the message center displays important vehicle information through a constant monitor of vehicle systems. Y ou may select display features on the message center for a display of status [...]

For maximum accuracy of this display feature, the ignition should be in the OFF position during fueling. The display FUEL LEVEL ERROR indicates a problem with the fuel indication system. See your dealer or qualified service technician for system maintenance. Fuel status Press once to display the approximate amount of fuel remaining in the fuel tank[...]

System check Press the system check control to display the status of the following systems: • engine oil life left • engine oil level • voltage level • engine coolant temperature • washer fluid level • fuel level The engine oil life left has two phases. The first display will indicate the oil change status (OK, SOON, REQUIRED). The seco[...]

Oil change reset Press the OIL CHANGE RESET control to reset the oil life feature to 100% (or your personalized oil reset percentage) (at optimal driving conditions, 100% oil life is equivalent to a maximum of 12 000 kilometers [7 500 miles]). After you have the oil changed, you must press and hold the OIL CHANGE RESET control for five seconds. The[...]

HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. Foglamp control (if equipped) T urn on the low-beam headlamps or parking lamps and press the foglamp control to activate the foglamps. The foglamp control will illuminate when the foglamps are[...]

Flash to pass Pull toward you to activate and release to deactivate. P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. • Rotate up to brighten. • Rotate down to dim. • Rotate to full up position (past detent) to turn on interior lamps. CLIMATE CONTROL SYSTEM Manual heating and a[...]

T emperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle. The air conditioning compressor can operate in all modes except and . However , the air conditioning will only function if the outside temperature is about 6°C (43°F) or hi[...]

• (Panel and floor)-Distributes outside air through the instrument panel registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode. For added customer comfort, when the temperature control knob is anywhere in between the full hot and full cold positions, the air distributed through the floor ducts will be [...]

• Remove any snow , ice or leaves from the air intake area (at the bottom of the windshield). • If your vehicle has been parked with the windows closed during hot weather , the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open. This will force most of the hot, stale air out of the v[...]

Turning the EA TC on Press AUTOMA TIC, any of the override controls or the fan speed control. The EA TC will only operate when the vehicle is running. Turning the EA TC off Press OFF . Automatic operation Press AUTOMA TIC and select the desired temperature. The selected temperature and the word AUTO will appear in the display window . The EA TC sys[...]

T emperature selection The display window indicates the selected temperature, function (AUTO or one of the override controls) and manual control of fan speed ( ) if automatic fan speed is not desired. T o control the temperature, select any temperature between 18°C (65°F) and 29°C (85°F) by pressing the blue (cooler) or red (warmer) buttons. Fo[...]

Fan speed ( ) When AUTOMA TIC is pressed, fan speed is adjusted automatically for existing conditions. Y ou can override fan speed at any time. T o control fan speed manually , use the thumbwheel or steering wheel control to cancel automatic fan speed operation. • Rotate the thumbwheel up for higher fan speed or down for lower fan speed. • Pres[...]

• MAX A/C-Uses recirculated air to cool the vehicle. The temperature will display 16°C (60°F). T o exit, press AUTOMA TIC or any other override controls. MAX A/C is noisier than normal A/C but more economical and will cool the inside of the vehicle faster . Airflow is from the instrument panel registers. This mode can also be used to prevent un[...]

Rear fan off Press REAR F AN OFF to turn off the rear console fan. This overrides the rear console fan speed control. The EA TC display window will indicate REAR F AN OFF . The rear console fan will remain off until REAR F AN OFF is pressed again. T o aid in defogging and demisting (removing condensation on the inside of the windshield) in cool wea[...]

• Remove any snow , ice or leaves from the air intake area (at the bottom of the windshield). • If your vehicle has been parked with the windows closed during hot weather , the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open. This will force most of the hot, stale air out of the v[...]

T urn the fan speed control to the desired position. Select for air to flow through these vents: Select for air to flow through these vents: - VOLUME + MODE SEEK MEMORY SEEK – VOLUME + BAND MEMORY SEEK – VOLUME + BAND MEMORY Controls and features 32[...]

REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog. • A small LED will illuminate when the rear defroster is activated. The ignition must be in the ON position to operate the rear window defroster . The defroster turns off automatically[...]

T o help avoid personal injury , always use caution when in reverse and when using the reverse sensing system. This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle. The system may not detect sm[...]

The reverse sensing system is automatically enabled when the gear selector is placed in R (Reverse) and the ignition is ON. A reverse sensing control allows the driver to disable the reverse sensing system only when the ignition is ON, and the gear selector is in R (Reverse). The OFF indicator remains illuminated when the system is disabled. The sy[...]

V olume/power control Press the control to turn the audio system on or off. T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in [...]

Tune adjust The tune control works in radio mode. Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly . • Press to move to the next frequency up the band (whether or not a listenable station is located there[...]

Setting memory preset stations 1. Select the frequency band with the AM or the FM select control. 2. Select a station. Refer to T une adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. Bass adjus[...]

Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. T ape select • T o enter tape mode while in radio mode, press the T APE AMS control. Automatic Music Search The Automatic Music Search feature allows you to q[...]

selection). The tape deck stops and returns to play mode when the AMS circuit senses a blank section on the tape. In order to ensure proper operation of the AMS feature, the tape MUST have a blank section of at least four seconds duration between programs. Rewind The rewind control works in tape mode. T o rewind in tape mode, press the REW control.[...]

Setting the clock Press CLK to toggle between listening frequencies and clock mode while in radio mode. T o set the hour , press and hold the CLK control and press the SEEK control: • to decrease hours and • to increase hours. T o set the minute, press and hold the CLK control and press the TUNE control: • to decrease minutes and • to incre[...]

When in clock mode, the media information will display for 10 seconds, when the radio is turned on, and then revert to clock information. Anytime that the media is changed, (new radio station, etc.), the media information will again display for 10 seconds before reverting back to the clock. In media mode, the media information will always be displa[...]

T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio and CD modes. AM/FM select in radio mode This control allows you to se[...]

Tune adjust for CD changer (if equipped) • Press to select the previous disc in the CD changer . (Play will begin on the first track of the disc unless the CD changer is in shuffle mode. Refer to Shuffle feature for more information. Hold the control to continue reversing through the disc. • Press to select the next disc in the CD changer . Hol[...]

Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode. Scan function in CD mode Press the SCAN control to hear a short sampling of all selections on the CD. (The CD scans in a forward direction, wrapping back to the first track[...]

Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. CD select • T o begin CD play (if CD[s] are loaded), press the CD control. The first track of the disc will begin playing. After that, CD play will begin wher[...]

Fast forward The fast forward control works in CD mode. T o fast forward in CD changer mode, press the CD control (preset 2). Press the control again to deactivate fast forward mode. Eject function Press the control to stop and eject a CD. Compression feature Compression adjust brings soft and loud CD passages together for a more consistent listeni[...]

• to decrease hours and • to increase hours. T o set the minute, press and hold the CLK control and press the TUNE control: • to decrease minutes and • to increase minutes. Premium AM/FM Stereo/Cassette/Single CD SEEK DISCS TUNE SEEK DISCS TUNE SEEK TUNE SEEK TUNE FM 1 AMC BL RF REW FF SCAN BASS TREB SEL BAL TAPE DISC EJ CD FADE AUTO CLK SI[...]

V olume/power control Press the control to turn the audio system on or off. Audio power can also be turned on by pressing the AM/FM select control or the tape/CD select control. Audio power is turned off by using the volume/power control. T urn control to raise or lower volume. If the volume is set above a certain level and the ignition is turned o[...]

Tune adjust The tune control works in radio or CD changer mode. Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly . • Press to move to the next frequency up the band (whether or not a listenable station is[...]

Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. Seek function in tape mode • Press to listen to the previous selection on the tape. • Press to listen to the next selection on the tape. Seek function for CD or CD changer (if eq[...]

Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’ s first side, direction automatically reverses to the opposite side of the tape.) T o stop on a particular selection, press the control again. Scan function in CD or CD changer m[...]

Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all[...]

Press the TREB control then press: • to decrease the treble output and • to increase the treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control then press: • to shift sound to the left and • to shift sound to the right. Speaker fade adjust Speaker sound can[...]

T ape/CD select • T o begin tape play (with a tape loaded into the audio system) while in the radio or CD mode, press the T APE control. Press the button during rewind or fast forward to stop the rewind or fast forward function. • T o begin CD play (if CD(s) are loaded), press the CD control. The first track of the disc will begin playing. If r[...]

T ape direction select Press SIDE 1–2 to play the alternate side of a tape. Eject function Press the EJ control to stop and eject a tape. Press the EJ control to stop and eject a CD. Dolby T noise reduction Dolby t noise reduction operates in tape mode. Dolby t noise reduction reduces the amount of hiss and static during tape playback. Press the [...]

Shuffle feature The shuffle feature operates in CD mode (if equipped) and plays all tracks on the current disc in random order . If equipped with the CD changer , the shuffle feature continues to the next disc after all tracks on the current disc are played. Press the SHUFFLE control to start this feature. Random order play will continue until the [...]

T o set the minute, press and hold the CLK control and press TUNE: • to decrease minutes and • to increase minutes. If your vehicle has a separate clock module, (other than the digital radio display), the CLK button will not function in the above manner . The CLK button will allow you to switch between media display mode (radio station, stereo [...]

Rear seat controls (if equipped) The Personal Audio System, a feature of the optional Premium AM/FM Stereo/Cassette/Single CD and the MACH t Audio System with AM/FM Stereo/Cassette/Single CD, allows front and middle seat passengers to listen to different media sources (radio, cassette or CD) simultaneously . However , the front and middle-seat pass[...]

Adjusting the volume Press the + control to increase volume. Press the - control to decrease volume. From the rear seat controls, volume control can be set no higher than the current radio setting unless the speakers are turned off. Refer to T urning speakers on and off. Turning the speakers on and of f Press to turn all speakers on or off. Using h[...]

Mode select Push the MODE control to toggle between AM, FM1, FM2, tape, CD or CD changer (if equipped). Memory preset control Push the MEMORY control successively to allow rear seat passengers to scroll through the 6 memory presets in AM, FM1 or FM2. Push the MEMORY control in CD changer mode (if equipped) to advance to the next disc. Seek function[...]

MACH T Audio System with AM/FM Stereo/Cassette/Single CD V olume/power control Press the control to turn the audio system on or off. T urn control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned bac[...]

volume level, turn the audio system off with the power control before switching off the ignition. AM/FM select The AM/FM select control works in radio, tape and CD modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in t[...]

Tune adjust for CD changer (if equipped) • Press to select the previous disc in the CD changer . (Play will begin on the first track of the disc unless the CD changer is in shuffle mode. Refer to Shuffle feature for more information. Hold the control to continue reversing through the disc. • Press to select the next disc in the CD changer . Hol[...]

Seek function for CD changer (if equipped) • Press to seek to the previous track of the current disc. If a selection has been playing for three seconds or more and you press , the CD changer will replay that selection from the beginning. • Press to seek forward to the next track of the current disc. After the last track has been completed, the [...]

Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to T une adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. Autoset memory pr[...]

• to decrease bass output and • to increase bass output. Treble adjust The treble adjust control allows you to increase or decrease the audio system’ s treble output. Press the TREB control then press: • to decrease treble output and • to increase treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the[...]

Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the F ADE control then press: • to shift sound to the front and • to shift sound to the rear . T ape/CD/CD changer (if equipped) select • T o begin tape play (with a tape loaded into the audio system) while in the radio or CD mode, press the T APE con[...]

• In CD mode, pressing the REW control for less than three seconds results in slow rewind. Pressing the control for more than three seconds results in fast rewind. Fast forward The fast forward control works in tape and CD modes. • In the tape mode, tape direction will automatically reverse when the end of the tape is reached. • In CD mode, p[...]

Compression adjust Compression adjust brings soft and loud CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust. Shuffle feature The shuffle feature operates in CD mode and plays all tracks on the current disc in random order . If equipped with the CD changer , the shuffle [...]

T o set the minute, press the clock/RDS control until SELECT MIN is displayed and press: • to decrease minutes and • to increase minutes. Radio Data System (RDS) feature This feature allows your audio system to receive text information from RDS-equipped FM radio stations. Press and hold the control for three seconds to turn the feature on or of[...]

RDS traffic announcement • Press the RDS control until TRAFFIC is displayed. • Use the SELECT control to select ON or OFF . W ith the feature ON, use the SEEK or SCAN control to find a radio station broadcasting a traffic report (if it is broadcasting RDS data). RDS select program type • Press the RDS control until FIND program type is displa[...]

• Classic • Country • Info • Jazz/R&B • Religious • Rock • Soft • To p 4 0 RDS show • W ith the RDS menu enabled, press the RDS control until SHOW is displayed. • Use the SEL control to select TYPE, NAME, TEXT or NONE. When your radio is turned to a RDS station, RDS station TYPE, station NAME, or TEXT message will be display[...]

Rear seat controls (if equipped) The Personal Audio System, a feature of the optional Premium AM/FM Stereo/Cassette/Single CD and the MACH t Audio System with AM/FM Stereo/Cassette/Single CD, allows front and middle seat passengers to listen to different media sources (radio, cassette or CD) simultaneously . However , the front and middle-seat pass[...]

Adjusting the volume Press the + control to increase volume. Press the - control to decrease volume. From the rear seat controls, volume control can be set no higher than the current radio setting unless the speakers are turned off. Refer to T urning speakers on and off. Turning the speakers on and of f Press to turn all speakers on or off. Using h[...]

Mode select Push the MODE control to toggle between AM, FM1, FM2, tape, CD or CD changer (if equipped). Memory preset control Push the MEMORY control successively to allow rear seat passengers to scroll through the 6 memory presets in AM, FM1 or FM2. Push the MEMORY control in CD changer mode (if equipped) to advance to the next disc. Seek function[...]

CD changer (if equipped) The CD changer is located in one of the following locations: • in the trunk • in the center console • under the driver’ s seat 1. Slide the door to access the CD changer magazine. 2. Press to eject the magazine. 3. T urn the magazine (A) over . 4. Using the disc holder release knob (C), pull the disc holder (B) out [...]

If you pull too hard on the disc holder , the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine while pressing on the lever (A). 5. Line up the CD with the groove of the disc holder . Ensure that the label on the CD faces downwards. 6. Press in on the disc holder until it locks sec[...]

The CD magazine may be inserted or ejected with the radio power off. ONL Y use the magazine supplied with the CD changer , other types will damage the unit. Keep the CD changer door closed. Coins and foreign objects will damage the CD player and void your audio system warranty . Do not insert any promotional (odd shaped or sized) discs, or discs wi[...]

• Do not insert more than one disc into each slot of the CD changer magazine. Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur . Cleaning cassette player (if equipped) Clean the tape player head with a cassette cleaning cartridge after 10 to 12 hours of play in order[...]

• T errain. Hills, mountains and tall buildings between your vehicle’ s antenna and the radio station signal can cause FM reception problems. Static can be caused on AM stations by power lines, electric fences, traffic lights and thunderstorms. Moving away from an interfering structure (out of its “shadow”) returns your reception to normal.[...]

4. ON, all electrical circuits operational. W arning lights illuminated. Key position when driving. 5. ST ART , cranks the engine. Release the key as soon as the engine starts. SPEED CONTROL (IF EQUIPPED) T o turn speed control on • Press ON. V ehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not u[...]

T o set a speed • Press SET/SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal. Speed control cannot reduce the vehicle speed if i[...]

Y ou can accelerate with the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle to the previously programmed set speed. T o set a lower set speed • Press and hold CST/COAST . Release the control when the desired speed is reached or • Press and release CST/COAST to operate the T ap-[...]

T o disengage speed control • Depress the brake pedal or • Depress the clutch pedal (if equipped). Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. OFF ON Controls and features 85[...]

T o return to a previously set speed • Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). Indicator light This light comes on when either the SET ACCEL or RES controls are pressed. It turns off when the speed control OFF control is pressed, the brake is applied or the ignition is turned to[...]

TIL T STEERING WHEEL (IF EQUIPPED) Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control to lock the steering wheel in position. Never adjust the steering wheel when the vehicle is moving. HAZARD FLASHER For information on the haz[...]

Push (tap) the end of the stalk briefly for a single swipe (no wash). Push and hold for three swipes with wash. Push and hold for a longer wash (up to ten seconds). Speed dependent wipers When the windshield wiper control is set on the intermittent settings, speed-sensitive front wipers automatically adjust as the vehicle’ s speed changes. Rear w[...]

STEERING WHEEL CONTROLS (IF EQUIPPED) These controls allow you to operate some radio and climate control features. Radio control features • Press BAND/MODE to select AM, FM1, FM2, T APE or CD (if equipped). In Radio mode: • Press MEM/NEXT to select a preset station from memory . In T ape mode: • Press MEM/NEXT to listen to the next selection [...]

OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’ s overhead console will vary according to your option package. Storage compartment (if equipped) Press the OPEN control to open the storage compartment. The door will open slightly and can be moved to full open. Installing a garage door opener (if equipped) The storage compartment can[...]

• Place the provided height adaptors onto the back of the GARAGE control as needed. • Press the GARAGE control to activate the transmitter . Moon roof (if equipped) Y ou can move the moon roof back to open the glass panel or tilt up to ventilate the vehicle. T o open the moon roof: The moon roof is equipped with an automatic, one-touch, express[...]

Do not let children play with the moon roof. They may seriously hurt themselves. Electronic compass/temperature display (if equipped) Outside air temperature The outside temperature display is contained in the overhead console. The temperature display can be turned off and on by pressing the MODE control on the overhead console. The temperature can[...]

Compass zone adjustment 1. Determine which magnetic zone you are in by referring to the zone map. 2. Press and hold the MODE control until V AR appears in the display , then release. The display should show the current zone number . 3. Press the MODE control until the desired zone number appears. The display will flash and then return to normal ope[...]

Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines: • Press and hold the MODE control until CAL appears in the display (approximately eight seconds) and release. • Drive the vehicle slowly (less than 5 km/h [3 mph]) in circles until CAL indicator turns off in about 2–3 comp[...]

Programming 1. Prepare for programming the HomeLink t Universal T ransceiver by erasing the three factory default codes by holding down the two outside buttons until the red light begins to flash after 20 seconds. Release both buttons. 2. Hold the end of your hand-held transmitter 5–14 cm (2–5 inches) away from the HomeLink t Universal T ransce[...]

T o program your hand-held transmitters: • continue to hold the button on the HomeLink t Universal T ransceiver . • press and re-press the hand-held transmitter button every two seconds until the red light changes from a slow to a fast flash. Operating the HomeLink T Universal T ransceiver Once programmed, the HomeLink t Universal T ransceiver [...]

3. Press and release the programmed HomeLink t button. Press and release the HomeLink t button a second time to complete the training process. (Some garage door openers may require this procedure to be done a third time to complete the training). The 2nd or 3rd press from step 3 will activate the door . The HomeLink t Universal T ransceiver has now[...]

Operating T ravelNote T T ravelNote t records and stores messages for up to three minutes in total length with simple controls. When you get an idea or remember something important while you’re driving, you don’t have to try to scribble it down or pull off the side of the road. All you have to do is push a button and begin speaking. T o record [...]

T o delete a message: 1. Press and release the DEL button while listening to a message or shortly after . The indicator light will flash green twice. 2. T o delete all recorded messages, simultaneously press and release the PLA Y and REC buttons at the same time. The indicator light will flash green twice. If the DEL button is inadvertently pressed[...]

4. The autolamp automatically turns the lamps on and off. The indicator light will illuminate when the headlamps turn on. AUTOMATIC DIMMING REAR VIEW MIRROR The autolamp/automatic dimming mirror is equipped with an automatic dimming feature. This feature will change from the normal state to the non-glare “active” state when bright lights (glare[...]

One touch down • Press AUTO completely down and release quickly . The driver’ s window will open fully . Depress again to stop window operation. One touch down can be deactivated during operation by pushing down on the top part of the driver power window control. Window lock The window lock feature allows only the driver to operate the power wi[...]

CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door . Setting the lock for one door will not automatically set the lock for b[...]

Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors. Fold-away mirrors Pull the si[...]

Use only soft cups in the cupholder . Hard objects can injure you in a collision. Auxiliary power point The power point is an additional power source for electrical accessories. Rear console features The rear console incorporates the following features: • air vents • audio system controls • rear seat climate controls • cupholders Controls a[...]

CENTER ARMREST/REAR CUPHOLDER (IF EQUIPPED) Do not attempt to raise the console armrest when the rear cupholder is in use. If you find resistance when raising the armrest, make sure the cupholder is fully closed or else damage may occur to the armrest. POSITIVE RETENTION FLOOR MA T Position the floor mat so that the eyelet is over the pointed end o[...]

The liftgate door and window should be closed before driving your vehicle. If not, possible damage may occur to the liftgate door lift cylinders and attaching hardware. Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. I[...]

1. Remove the shade from the vehicle and extend it with the smooth grain facing you. 2. W rap the vinyl around the roller tube twice. T uck the edges of the vinyl inside the end cap with each wrap. 3. Fold the edges of the vinyl towards the center , making sure that the edges clear the end cap slots. Use tape or a rubber band to hold the vinyl to t[...]

Unlocking the doors Press this control to unlock the driver’ s door . The interior lamps will illuminate. Press the control a second time within five seconds to unlock all doors. Locking the doors Press this control to lock all doors. T o confirm all doors are closed and locked, press the control a second time within five seconds. The doors will [...]

Changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment. Memory seat feature (if equipped) The remote entry system can also control the memory seat feature. Press the control once to unlock the driver’ s door and move the memory seat feature to the corresp[...]

The memory feature will continue to work from the door control even when deactivated at the remote entry module. Replacing the battery The transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. T ypical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle. A decrease in operating ra[...]

Replacing lost transmitters If a remote transmitter has been lost and you would like to remove it from the vehicle’ s memory , or you would like to purchase additional remote transmitters and have them programmed to your vehicle: • T ake all your vehicle’ s transmitters to your dealer for programming, or • Perform the programming procedure [...]

Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm. The system automatically turns off after 25 seconds or when the ignition is turned to the RUN or ACC position. The dome lamp control (if equipped) must not be set to the OFF position for the illuminated entry syste[...]

Programming your own personal entry code 1. Enter the factory-set code (keypad will illuminate when pressed). 2. Press the 1/2 control within five seconds of step 1. 3. Enter your personal 5 digit code. Enter each digit within five seconds of the previous one. Do not set a code that includes five of the same number or presents them in sequential or[...]

T o unlock all doors, enter the factory-set code or personal code (driver door unlocks) and press the 3/4 control within five seconds. Locking the doors with the keyless entry system T o lock all the doors, press 7/8 and 9/0 at the same time. It is not necessary to first enter the keypad code. Autolock The autolock feature will lock all of the vehi[...]

2. Press and release the 3/4 control while holding the 7/8 control. 3. Release the 7/8 control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. T o reactivate autolock, repeat steps 1 through 3. Autolock can also be activated or deactivated using the following procedure: Y ou m[...]

SECURILOCK Y PASSIVE ANTI-THEFT SYSTEM The SecuriLock y passive anti-theft system provides an advanced level of vehicle theft protection. Y our vehicle’ s engine can only be started with the two special SecuriLock y electronically coded keys provided with your vehicle. Each time you start your vehicle, the SecuriLock y key is read by the SecuriLo[...]

Theft indicator The theft indicator on the instrument cluster will operate as follows: • When the ignition is OFF , the theft indicator will flash briefly every two seconds to indicate the SecuriLock y system is protecting your vehicle. • When the ignition is turned to ON or ST ART , the theft indicator will light for three seconds and then go [...]

3. W ithin five seconds of turning the ignition to OFF , insert the second previously programmed SecuriLock y key into the ignition and turn the ignition from OFF to ON (maintain ignition in ON for at least one second but no more than five seconds). 4. T urn the ignition to OFF and remove the second SecuriLock y key from the ignition. 5. W ithin 10[...]

SEA TING Adjustable head restraints (if equipped) Y our vehicle’ s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. T o properly adjust your head restraints, lift the head restraint so that it is located directly behind y[...]

Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’ s safety belt in the event of a collision. Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Adjusting the front power seat (if equipped) Never adjust the dr[...]

Reclining the seatback can reduce the effectiveness of the seat’ s safety belt in the event of a collision. The control is located on the outboard side of the seat cushion. Press front to raise or lower the front portion of the seat cushion. Press rear to raise or lower the rear portion of the seat cushion. Press the control to move the seat forw[...]

Memory seats (if equipped) This system allows automatic positioning of the driver seat to three programmable positions. The memory seat control is located on the driver door . • T o program position one, move the driver seat to the desired position using the seat controls. Press the SET control. The SET control indicator light will briefly illumi[...]

Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press one side of the control to adjust firmness. Press the other side of the control to adjust softness. REAR SEATS Head restraints Y our vehicle’ s seats may be equipped with head restraints which are vertically adjustable. The pur[...]

1. Press the lower release control downward to unlatch the seatback. 2. Rotate the seatback downward into the load floor position. 3. Press down on the top outboard area of the seatback until a click is heard. The seat is now latched in the floor position. Seating and safety restraints 124[...]

T o return the seat to the upright position: • Press downward on the upper corner of the seatback and hold. • Pull the release handle upward to unlatch the seat. • Rotate the seatback upward until the seatback latches in the upright position. The seatback will click when it is locked into position. SAFETY RESTRAINTS Safety restraints precauti[...]

All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an air bag SRS is provided. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in a[...]

After any vehicle collision, the safety belt system at all outboard seating positions (except driver , which has no “automatic locking retractor” feature) must be checked by a qualified technician to verify that the “automatic locking retractor” feature for child seats is still functioning properly . In addition, all safety belts should be [...]

The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes described below: V ehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements[...]

• Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retrac[...]

Front safety belt height adjustment Y our vehicle has safety belt height adjustments for the driver and front passenger . Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder . T o lower the shoulder belt height, push the button and slide the height adjuster down. T o raise the height of the shoulder belt, sli[...]

Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position... The safety belt warning light illuminates1-2 minutes and the warning chime sounds 4-8 seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding..[...]

The purpose of the Belt Minder is to remind occasional wearers to wear safety belts all of the time. The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... Consider ... 9 Crashes are rare events 9 36 700 crashes occur every day . The more we drive, the more we are exposed to 9 r[...]

Reasons given... Consider ... 9 The people I’m with don’t wear belts 9 Set the example, teen deaths occur 4 times more often in vehicles with TWO or MORE people. Children and younger brothers/sisters imitate behavior they see. 9 I have an air bag 9 Air bags offer greater protection when used with safety belts. Frontal airbags are not designed t[...]

• the driver’ s safety belt is unbuckled • the parklamps/headlamps are in OFF position (If vehicle is equipped with Autolamps, the Autolamps feature MUST be turned off.) T o reduce the risk of injury , do not deactivate/activate the Belt Minder feature while driving the vehicle. 1. T urn the ignition switch to the RUN (or ON) position. (DO NO[...]

Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, wears or cuts, replacing if necessary . All safety belt assemblies, including retractors, buckles, front seat belt buckle assemblies, buckle support assemblies (slide bar[...]

Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim covering th[...]

Do not put anything on or over the air bag module. Placing objects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causing serious injury . Do not attempt to service, repair , or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln Mercury deale[...]

How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the[...]

Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately . If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision. The SRS consists of: • driver and passenger air bag m[...]

If any of these things happen, even intermittently , have the SRS serviced at your dealership or by a qualified technician immediately . Unless serviced, the system may not function properly in the event of a collision. Side air bag system (if equipped) Do not place objects or mount equipment on or near the air bag cover on the side of the seatback[...]

How does the side air bag system work? The side air bag system consists of the following: • An inflatable nylon bag (air bag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks. • A special seat cover designed to allow airbag deployment. • The same warning light, electronic control and diagn[...]

Several air bag system components get hot after inflation. Do not touch them after inflation. If the side air bag has deployed, the air bag will not function again. The side air bag system (including the seat) must be inspected and serviced by a qualified technician in accordance with the vehicle service manual. If the air bag is not replaced, the [...]

Disposal of air bags and air bag equipped vehicles (including pretensioners) For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel. SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints [...]

neck, the child should wear the lap and shoulder belt. Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit. Do not leave children, unreliable adults, or pets unattended in your vehicle. T o improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a [...]

When installing a child safety seat: • Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter . • Use the correct safety belt buckle for that seating position (the buckle closest to the direction the tongue is coming from). • Insert the belt tongue into the proper buckle until you hear[...]

Installing child safety seats in combination lap and shoulder belt seating positions Air bags can kill or injure a child in a child seat. NEVER place a rear -facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back. 1. Position the child safety seat in a seat with[...]

3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until y[...]

7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly tilt the seat forward and back to make sure the seat is securely held in pla[...]

The provision (attaching hole) is provided in the rear edge of the front passenger seat cushion frame. The anchorbracket must be installed using the instructions provided with the kit. T ether anchorage hardware kits (part number 613D74) including instructions, may be obtained at no charge from any Ford or Lincoln/Mercury dealer . T ighten the anch[...]

PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use [...]

2. Make sure the headlamps and vehicle accessories are off. If starting a vehicle with an automatic transmission: • Make sure the parking brake is set. • Make sure the gearshift is in P (Park). If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Push the clutch pedal to the floor . 3. T urn the key to 4[...]

• steering wheel is turned when getting in or out of the vehicle Make sure the corresponding lights illuminate briefly . If a light fails to illuminate, have the vehicle serviced. • If the driver’ s safety belt is fastened, the light may not illuminate. ST ARTING THE ENGINE 1. T urn the key to 5 (ST ART) without pressing the accelerator pedal[...]

Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater -defroster system to respond quickly . Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below . For best resul[...]

Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air . Improve vehicle ventilation by keeping all air inlet vents clear of snow , leaves and other debris.[...]

BRAKES Y our service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’ s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the b[...]

ABS warning lamp ABS The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. W ith the ABS light on, the anti-lock brake system is disabled and normal braking is sti[...]

The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission). The parking brake is not recomm[...]

• underinflated tire(s) on any wheel(s) • high crown in center of road • high crosswinds • wheels out of alignment • loose or worn components in steering linkage AIR SUSPENSION SYSTEM (IF EQUIPPED) The load leveling feature of the air suspension automatically keeps the vehicle at a constant level if a load is added or removed from the veh[...]

In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Y our vehicle has special design and equipment features to make it capable of performing in a wide variety of circumstances. These special design features, such as larger tires and increased ground clearance, give the vehicle a higher cent[...]

2. Insert the key and turn it to OFF . Apply the brake pedal and shift to N (Neutral). 3. Start the vehicle. If it is necessary to use the above procedure to move the gearshift lever , it is possible that a fuse has blown or the vehicle’ s brakelamps are not operating properly . Refer to Fuses and relays in the Roadside emergencies chapter . Do n[...]

Understanding gearshift positions P (Park) Always come to a complete stop before shifting into P (Park). Make sure the gearshift lever is securely latched in P (Park). This position locks the transmission and prevents the rear wheels from turning. Always set the parking brake fully and make sure the gearshift lever is latched in P (Park). T urn off[...]

The transmission control indicator light (TCIL) will illuminate on the instrument cluster . Drive – Not shown on the display . Activate by pressing the transmission control switch on the end of the gearshift lever with the gearshift in the position. The O/D OFF indicator will illuminate on the instrument cluster . T ransmission operates in gears [...]

Forced Downshifts T o gain acceleration in (Overdrive) or Drive (O/D OFF) when passing another vehicle, push the accelerator to the floor . The transmission will downshift to the appropriate gear: third, second or first gear . Driving with a 5–speed automatic transmission (if equipped) Y our automatic transmission electronically controls the shif[...]

Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn off the ignition whenever you leave your vehicle. R (Reverse) W ith the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) W ith the gearshift lever in N (N[...]

Drive – Not shown on the display . Activate by pressing the transmission control switch on the end of the gearshift lever with the gearshift in the (Overdrive) position. The TCIL will illuminate on the instrument cluster . T ransmission operates in gears one through four . Drive (O/D OFF) provides more engine braking than (Overdrive) and is usefu[...]

Driving a manual transmission (if equipped) Using the clutch V ehicles equipped with a manual transmission have a starter interlock that prevents Starting the engine unless the clutch pedal is fully depressed. When starting a vehicle with a manual transmission: 1. Hold down the brake pedal. 2. Put the gearshift lever in N (Neutral). 3. Depress the [...]

2. Engage the parking brake. 3. Shift into 1 (First). 4. T urn the ignition to Off. Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully . Recommended shift speeds Upshifts when accelerating (recommended for best fuel economy) Shift from: T ransfer case position (if equ[...]

Maximum downshift speeds Shift from: T ransfer case position (if equipped) 1 AUTO or HIGH LOW 5 (Overdrive) - 4 88 km/h (55 mph) 34 km/h (21 mph) 4 - 3 72 km/h (45 mph) 27 km/h (17 mph) 3 - 2 56 km/h (35 mph) 21 km/h (13 mph) 2 - 1 32 km/h (20 mph) 11 km/h (7 mph) Reverse Ensure that the vehicle is at a complete stop before shifting into R (Reverse[...]

Positions of the Control-T rac system The Control-T rac system functions in three modes: • The 4WD AUTO mode provides four -wheel drive with full power delivered to the rear axle, and to the front axle as required for increased traction. This is appropriate for normal on-road operating conditions, such as dry road surfaces, wet pavement, snow and[...]

tire could result in damage to driveline components and make the vehicle difficult to control. Utility and four -wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. A void sharp turns or abrupt maneuvers in these[...]

Shifting from 4WD LOW to 4WD AUTO or 4WD HIGH 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral) (automatic transmission) or depress the clutch (manual transmission). 4. Move the 4WD control to the 4WD AUTO or 4WD HIGH position. Driving off-road with 4WD Y our vehicle is specially equipped for driving on san[...]

Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. Do not reduce the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels. Mud and water If you must drive through high water , drive slowly . T raction or brake capability[...]

When speed control is on and you are driving uphill, your vehicle speed may drop considerably , especially if you are carrying a heavy load. If vehicle speed drops more than 16 km/h (10 mph), the speed control will cancel automatically . Resume speed with accelerator pedal. If speed control cancels after climbing the hill, reset speed by pressing a[...]

Driving off-road with A WD Y our vehicle is specially equipped for driving on sand, snow , mud and rough terrain and has operating characteristics that are somewhat different from conventional vehicles, both on and off the road. Maintain steering wheel control at all times, especially in rough terrain. Since sudden changes in terrain can result in [...]

When driving through water , determine the depth; avoid water higher than the bottom of the hubs (if possible) and proceed slowly . If the ignition system gets wet, the vehicle may stall. Once through water , always try the brakes. W et brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly[...]

Automatic transmissions may shift frequently while driving up steep grades. Eliminate frequent shifting by shifting out of (Overdrive) into D (Drive). Driving on snow and ice An A WD vehicle has advantages over 2WD vehicles in snow and ice but can skid like any other vehicle. A void sudden applications of power and quick changes of direction on sno[...]

• GVWR (Gross V ehicle W eight Rating): Maximum total weight of the base vehicle, passengers, optional equipment and cargo. The GVWR is specific to each vehicle and is listed on the Safety Certification Label on the driver’ s door pillar . • GA WR (Gross Axle W eight Rating): Carrying capacity for each axle system. The GA WR is specific to ea[...]

to the front of your vehicle, (potentially including weight added to the cab), the weight added should not exceed the front axle reserve capacity (F ARC). Additional frontal weight may be added to the front axle reserve capacity provided you limit your payload in other ways (i.e. restrict the number of passengers or amount of cargo carried). Always[...]

DRIVING THROUGH WATER Do not drive quickly through standing water , especially if the depth is unknown. T raction or brake capability may be limited and if the ignition system gets wet, your engine may stall. W ater may also enter your engine’ s air intake and severely damage your engine. If driving through deep or standing water is unavoidable, [...]

Do not exceed the maximum loads listed on the Safety Compliance Certification label. For load specification terms found on the label, refer to V ehicle loading in this chapter . Remember to figure in the tongue load of your loaded vehicle when figuring the total weight. T railer towing table (4x2 w/manual transmission) GCWR (Gross Combined W eight [...]

T railer towing table (4x4 w/manual transmission) GCWR (Gross Combined W eight Rating)/T railer weights Engine Rear axle ratio Maximum GCWR-kg (lbs.) T railer weight range-kg (lbs.) (0-Maximum) Maximum frontal area of trailer -m 2 (ft 2 ) 2-door 4.0L OHV 3.27 2 721 (6 000) 0-907 (0-2 000) 4.64 (50) 4.0L OHV 3.55 2 948 (6 500) 0-1 134 (0-2 500) 4.64[...]

T railer towing table (4x2 w/automatic transmission) GCWR (Gross Combined W eight Rating)/T railer weights Engine Rear axle ratio Maximum GCWR-kg (lbs.) T railer W eight Range-kg (lbs.) 0-Maximum Maximum frontal area of trailer -m 2 (ft 2 ) 2-door 4.0L 3.55 3 629 (8 000) 0-1 887 (0-4 160) 4.64 (50) 4.0L OHV 3.73 4 082 (9 000) 0-2 341 (0-5 160) 4.64[...]

T railer towing table (4x2 w/automatic transmission) Notes: For high altitude operation, reduce GCW by 2% per 300 meters (1 000 ft) elevation. For definition of terms and instructions on calculating your vehicle’ s load, refer to V ehicle loading in this chapter . Maximum trailer weights shown. The combined weight of the completed towing vehicle [...]

T railer towing table (4x4 and A WD with automatic transmission) 4.0L SOHC 3.73 4 535 (10 000) 0-2 604 (0-5 740) 4.64 (50) 4.0L SOHC 4.10 4 535 (10 000) 0-2 604 (0-5 740) 4.64 (50) 5.0L 3.55 4 535 (10 000) 0-2 549 (0-5 620) 4.64 (50) 5.0L 3.73 4 990 (11 000) 0-3 003 (6 620) 4.64 (50) Notes: For high altitude operation, reduce GCW by 2% per 300 mete[...]

Safety chains Always connect the trailer’ s safety chains to the frame or hook retainers of the vehicle. T o connect the trailer’ s safety chains, cross the chains under the trailer tongue and allow slack for turning corners. If you use a rental trailer , follow the instructions that the rental agency gives to you. Do not attach safety chains t[...]

Driving while you tow When towing a trailer: • Ensure that you turn off your speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer . • Use a lower gear when towing up or down steep hills. This will eliminate excessive dow[...]

• Do not allow waves to break higher than 15 cm (6 inches) above the bottom edge of the rear bumper . Exceeding these limits may allow water to enter critical vehicle components, adversely affecting driveability , emissions, reliability and causing internal transmission damage. Replace the rear axle lubricant anytime the axle has been submerged i[...]

Improper removal/installation of the driveshaft can cause transmission fluid loss, damage to the driveshaft and internal transmission components. RWD vehicles with 4x4 electronic shift transfer case or All Wheel Drive (A WD) vehicles with automatic transmissions Regarding recreational towing or having your vehicle towed, 4x4 vehicles with electroni[...]

GETTING ROADSIDE ASSIST ANCE T o fully assist you should you have a vehicle concern, Ford offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24–hours, seven days a week • for the Basic warranty period (Canada) or New V ehicle Limited W arranty peri[...]

Roadside coverage beyond basic warranty In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer . Similarly in Canada, you may purchase additional coverage beyond the basic coverage period by consulting the Ford Roadside Assistance[...]

The fuel pump shut-off switch is located in the passenger’ s foot well, by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. T urn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. T ur[...]

Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color COLOR Fuse Rating Mini Fuses Standard Fuses Maxi Fuses Cartridge Maxi Fuses Fuse Link Cartridge 2A Grey Grey — — — 3A Violet Violet — ?[...]

Passenger compartment fuse panel The fuse panel is located on the left hand side of the instrument panel facing the driver’ s side door . Pull the panel cover outward to access the fuses. T o remove a fuse use the fuse puller tool provided on the fuse panel cover . 1 234 5 678 9 1 01 11 2 13 14 15 16 17 18 19 20 21 22 23 24 25 26 29 30 35 36 31 3[...]

The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 7.5A Power Mirror Switch, Power Antenna, Memory Seat 2 7.5A Blower Motor Relay , Air Bag Diagnostic Monitor 3 7.5A Left Stop/T urn T railer T ow Connector 4 10A Left Headlamp 5 10A Data Link Connector (DLC) 6 7.5A Rear Blower Motor (W [...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 16 30A W indshield Wiper Motor , W iper Hi-Lo Relay , W iper Run/Park Relay 17 25A Cigar Lighter 18 25A Drivers Unlock Relay , All Unlock Relay , All Lock Relay , Power Seats 19 25A PCM Power Diode 20 7.5A RAP Module, Generic Electronic Module (GEM), Radio 21 15A Flash[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 34 7.5A Rear Integrated Control Panel, CD 35 7.5A Rear Blower Motor (w/EA TC) 36 7.5A EA TC Memory , CD, Rear Integrated Control Panel, Memory Seat, Message Center Power distribution box The power distribution box is located in the engine compartment. The power distrib[...]

The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 60A** I/P Fuse Panel 2 40A** Blower Motor Relay 3 50A** 4 Wheel Anti-Lock Brake System (4W ABS) Module 4 30A** Power W indows, Power Moon Roof, Power Seat 5 50A** Ignition Switch, Starter Relay 6 20A** T ransfer Case Relay 7 — Not[...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 5 — Not Used 6 10A* Powertrain Control Module 7 30A* 4 Wheel Anti-Lock System (4W ABS) Module 8 15A* Rear W iper Motor 9 20A* Fuel Pump Relay and RAP Module 10 15A* Horn Relay 11 15A* Parklamps Relay and Mainlight Switch 12 30A* Mainlight Switch and Multifunction Switch 13 15A[...]

CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily . Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Spare tire information Y our vehicle is equipped with a 15” spare tire that must be used for emergencies only . V ehicles equipped[...]

Removing the spare tire 1. Insert the jack handle into the rear bumper opening. The handle will stop moving and forward resistance to turning will be felt when properly engaged. 2. T urn the handle counterclockwise until tire is lowered to the ground, the tire can be slid rearward and the cable is slightly slack. 3. Remove the retainer from the spa[...]

1. Park on a level surface, activate hazard flashers and set the parking brake. 2. Place gearshift lever in P (Park) or in the reverse gear (manual transmission) and turn engine OFF . When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the transmission is i[...]

On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. 6. T urn OFF the air suspension switch (if equipped). Refer to Air suspension system in the Driving chapter . 7. Position the jack according to the following guides and turn the jack handle clockwise until the tire is a ma[...]

T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. • Never use the front or rear differential as a jacking point. 8. Remove the lug nuts with the lug wrench. 9. Replace the flat ti[...]

JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. Y ou could damage the catalytic converter . Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted. Do not attempt [...]

Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery . Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . + – + – + [...]

3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding [...]

• 4.0L SOHC 5. Ensure that the cables are clear of fan blades, belts, moving parts of both engines, or any fuel delivery system parts. Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engin[...]

• Engines except 4.0L SOHC • 4.0L SOHC + – + – + – + – Roadside emergencies 208[...]

2. Remove the jumper cable on the negative (-) connection of the booster vehicle’ s battery . 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . + – + – + – + – Roadside emergencies 209[...]

4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions. + – + – Roadside emergencies 210[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member , your roadside assistance center . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. If equipped with[...]

SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a scheduled maintenance guide which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide the necessary parts and service. Check you[...]

3. T urn off the engine and remove the key . 4. Block the wheels to prevent the vehicle from moving unexpectedly . Working with the engine on • Automatic transmission: 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Block the wheels to prevent the vehicle from moving unexpectedly . Do not start your engine wi[...]

2. Go to the front of the vehicle and release the auxiliary latch that is located in the center between the hood and the grill. 3. Lift the hood until the lift cylinders hold it open. Maintenance and care 214[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L OHV V6 engine 1. W indshield washer fluid reservoir 2. Engine oil filler cap 3. T ransmission fluid dipstick (automatic transmission) 4. Engine oil dipstick 5. Power steering fluid reservoir 6. Brake fluid reservoir 7. Power distribution box 8. Clutch fluid reservoir (manual transmission) 9. Bat[...]

4.0L SOHC V6 engine 1. W indshield washer fluid reservoir 2. Automatic transmission fluid dipstick 3. Engine oil filler cap 4. Engine oil dipstick 5. Brake fluid reservoir 6. Power distribution box 7. Battery 8. Power steering fluid reservoir 9. Air filter assembly 10. Engine coolant reservoir 10 1 3 4 2 5 6 9 7 8 Maintenance and care 216[...]

5.0L V8 engine 1. Engine coolant reservoir 2. W indshield washer fluid reservoir 3. Engine oil filler cap 4. Automatic transmission fluid dipstick 5. Brake fluid reservoir 6. Power distribution box 7. Battery 8. Power steering fluid reservoir 9. Engine oil dipstick 10. Air filter assembly ENGINE OIL Checking the engine oil Refer to the scheduled ma[...]

3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmissions) or 1 (First) (manual transmissions). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). • 4.0L V6 engines • 5.0L V8 engine MAX MIN FULL ADD 1QT MAX MIN Maintenanc[...]

6. W ipe the indicator clean. Insert the indicator fully , then remove it again. • If the oil level is between the ADD and FULL marks or between the MIN and MAX marks (depending on application), the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the ADD mark or MIN mark, add enough oil to raise the level within the ADD-FUL[...]

Engine oil and filter recommendations SAE 5W -30 engine oil is recommended Look for this certification trademark. Use SAE 5W -30 motor oil certified for gasoline engines by the American Petroleum Institute (API). Motor oil displaying the API certification trademark will meet all requirements for your vehicle’ s engine. Ford oil specification is W[...]

BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the scheduled maintenance guide for the service interval schedules. 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir . 2. Visually inspect the fluid level. 3. If necessary , add brake fluid from a [...]

CLUTCH FLUID (IF EQUIPPED) Check the clutch fluid level. Refer to the scheduled maintenance guide for the service interval schedules. During normal operation, the fluid level in the clutch reservoir should remain constant. If the fluid level drops, refill the fluid level to the step in the reservoir . Use only a DOT 3 brake fluid designed to meet F[...]

WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low , add enough fluid to fill the reservoir . In very cold weather , do not fill the reservoir all the way . Only use a washer fluid that meets Ford specifications. Refer to Lubrica[...]

A 50/50 mixture of distilled water and Ford G05 Engine Coolant provides: • maximum cooling system efficiency . • freeze protection down to -36° C (-34° F). • boiling protection up to 129° C (265° F). • protection against rust and other forms of corrosion. • an accurate temperature readout from the engine coolant gauge. The engine cool[...]

Automotive fluids are not interchangeable; do not use engine coolant, antifreeze or windshield washer fluid outside of its specified function and vehicle location. Adding engine coolant Use only Ford Premium Engine Coolant E2FZ-19549-AA (in Canada, Motorcraft CXC-10) or a premium engine coolant that meets Ford specification ESE-M97B44-A. Use only F[...]

• Engine coolant concentrations above 60% or below 40% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage. Plain water may be added in an emergency , but you must replace it with a 50/50 mixture of engine coolant and distilled water as soon as possible. Check the coolant level in the reservoir be[...]

Always dispose of used automotive fluids in a responsible manner . Follow your community’ s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity T o find out how much fluid your vehicle’ s cooling system can hold, refer to Refill capacities in the Capacities and specifications chapter . Fill your e[...]

V ehicles driven year -round in non-extreme climates should use a 50/50 mixture of engine coolant and distilled water for optimum cooling system and engine protection. CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the scheduled maintenance guide for the service interval schedules. If adding fluid is necessary , u[...]

• 5.0L V8 engine 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C). 2. While the engine idles, turn the steering wheel left and right several times. 3. T urn the engine off. 4. If your vehicle is equipped with[...]

pulling a trailer , the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking. 1. Drive the vehicle 30 km (20 miles) or until it reaches normal operating temperature. 2. Park the vehicle on a level surface and engage the parking brake. 3. W ith the parking brake engaged and your foot on the brake pedal, start the [...]

High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correc[...]

2. Park the vehicle on a level surface and engage the parking brake. 3. W ith the parking brake engaged and your foot on the brake pedal, start the engine and move the gearshift lever through all of the gear ranges. Allow sufficient time for each gear to engage. 4. Latch the gearshift lever in P (Park) and leave the engine running. 5. Remove the di[...]

The transmission fluid should be in this range if at ambient temperature (10°C-35°C [50°F-95°F]). High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating [...]

Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely . Use on[...]

CHECKING AND ADDING TRANSFER CASE FLUID (IF EQUIPPED) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter . DRIVEL[...]

BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However , for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the scheduled maintenance guide for the service interval schedules. Keep the electrolyte l[...]

Batteries normally produce explosive gases which can cause personal injury . Therefore, do not allow flames, sparks or lighted substances to come near the battery . When working near the battery , always shield your face and protect your eyes. Always provide proper ventilation. When lifting a plastic-cased battery , excessive pressure on the end wa[...]

• The vehicle may need to be driven to relearn the idle and fuel trim strategy . • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned. When the battery is disconnected or a new battery installed, the transmission must relearn its adaptiv[...]

Changing the wiper blades T o replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. T urn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 3. Attach the new wiper to the wi[...]

T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the ac[...]

SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles). • Adjust tire pressure to recommended specifications found on the Certification Label or the T ire Label. Imp[...]

• 16’’ Five tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speed rating, and load-carrying[...]

Do not replace your tires with “high performance” tires or larger size tires. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over . T ires that are larger or smaller than your vehicle’ s original tires may also affect the accuracy of your speedome[...]

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing th[...]

• A void inhaling fuel vapors. Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury . • A void getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), fl[...]

Choosing the right fuel Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle. Do not use fuel containing methanol. It can damage critical fuel system components. Y our vehicle was not designed to use fuel or fuel additives with metallic compounds, including manganese-based compounds containing MMT . Repa[...]

Many of the world’ s automakers issued the W orld-wide Fuel Charter that recommends gasoline specifications to provide improved performance and emission control system protection for your vehicle. Gasolines that meet the W orld-wide Fuel Charter should be used when available. Ask your fuel supplier about gasolines that meet the W orld-wide Fuel C[...]

5. T urn the filler cap clockwise 1/8 of a turn until it stops. If the “Service Engine Soon/Check Engine” indicator comes on and stays on after you start the engine, the fuel filler cap may not be properly installed. T urn off the engine, remove the fuel filler cap, align the cap properly and reinstall it. If you must replace the fuel filler ca[...]

Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal to the rated refill capacity of the fuel tank as listed in the Refill Capacities section of the Capacities and specifications chapter . The advertised capacity is the amount of the indicated capacity and the empty reserve combined. Indicated capacity is the diff[...]

5. Follow one of the simple calculations in order to determine fuel economy: Multiply liters used by 100, then divide by total kilometers traveled. Divide total miles traveled by total gallons used. Keep a record for at least one month and record the type of driving (city or highway). This will provide an accurate estimate of the vehicle’ s fuel [...]

Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fuel economy . • Use recommended engine oil. Refer to Lubricant Specifications. • Perform all regularly scheduled maintenance items. Follow the recommended maintenance schedule and owner maintenance ch[...]

EMISSION CONTROL SYSTEM Y our vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. T o make sure that the catalytic converter and other emission control components continue to work properly: • Use only the specified fuel listed. [...]

Please consult your “W arranty Guide” for complete emission warranty information. Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostics system. If your “Check Engine/Service Engine Soon” light is on, refer to the description in the W arning Lights[...]

Replacing headlamp bulbs T o remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position, then lift hood and open the hinged headlamp cover . 2. Disconnect the electrical connector from the bulb by pulling rearward. 3. Remove the bulb retaining ring by rotating it counterclockwise (when viewed from the rear) to free it from the bulb s[...]

If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used. 1. W ith the flat side of the new bulb’ s plastic base facing upward, insert the glass end of the bulb into the lamp assembly . Y ou may need to turn the bulb left or right to align the grooves in the plastic base with the tabs in the lamp assembly .[...]

Replacing tail lamp/turn/backup lamp bulbs The tail lamp/turn/backup lamp bulbs are located in the tail lamp assembly , one just below the other . Follow the same steps to replace either bulb: 1. Open the liftgate to expose the lamp assemblies. 2. Remove the two screws from the lamp assembly . 3. Carefully remove the lamp assembly by pulling it rea[...]

Replacing license plate lamp bulbs 1. Remove two screws and the license plate lamp assembly from the liftgate. 2. Pull the bulb out from lamp assembly and push in the new bulb. 3. Install the lamp assembly on liftgate with two screws. Replacing high-mount brake lamp bulbs 1. Remove the two screws and move the lamp assembly away from the liftgate. 2[...]

4. Pull the bulb straight out of the socket and push in the new bulb. T o complete installation, follow the removal procedure in reverse order . USING THE RIGHT BULBS Replacement bulbs are specified in the chart below . Headlamp bulbs must be marked with an authorized “D.O.T .” for North America and an “E” for Europe to assure lamp performa[...]

AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by a qualified service technician. CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance chapter for a list of Ford-approved cleaners, polishes and wax[...]

Use only carnauba or synthetic-based waxes. Use a cleaning fluid with a clean cloth to remove any bugs before waxing your vehicle. Use tar remover to remove any tar spots. A void getting wax on the windshield, or on any surfaces which appear coarse or bumpy . If you have wax applied at a commercial car wash, it is recommended that you clean the wip[...]

• 5.0L • 4.0L SOHC Maintenance and care 261[...]

• 4.0L OHV • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning the wheels W ash with the same detergent as the body of your vehicle. Do not use acid-based or alcohol-based wheel cleaners, steel wool, fuel or strong detergents. Never use abrasives that will damage the finish of sp[...]

Cleaning the exterior lamps W ash with the same detergent as the exterior of your vehicle. If necessary , use a tar remover such as Ford Extra Strength T ar and Road Oil Remover (B7A-19520–AA). T o avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners. Cleaning the wiper blades, windshield and rear windo[...]

Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the air bag system. Cleaning the instrument cluster lens Clean with a damp cloth, then dry with a dry cloth. Do not use household or glass cleaners as these may damage the lens. Cleaning the overhead console Clean with a [...]

Do not use household cleaning products, alcohol solutions, solvents or cleaners intended for rubber , vinyl or plastics. Woodtone trim W ipe stains with a soft cloth and a multi-purpose cleaning solution. Inside windows Use Ultra-Clear Spray Glass Cleaner (E4AZ-19C507–AA) for the inside windows if they become fogged. Cleaning mirrors Do not clean[...]

MOTORCRAFT PART NUMBERS Component 4.0L OHV V6 engine 4.0L SOHC V6 engine 5.0L V8 engine Air filter element F A-1658 F A-1658 F A-1658 Fuel filter FG-986B FG-986B FG-986B Battery BXT -65-650 BXT -65-650 BXT -65-650 Oil filter FL-1A FL-1A FL-820S PCV valve EV -225 EV -225 EV -152 Spark plugs* AGSF-22PP AGSF-22PP A WSF-32EE * Refer to V ehicle Emissio[...]

Fluid Ford Part Name Application Capacity T ransmission fluid 1 Motorcraft MERCON t AT F 5-speed manual 2.6L (5.6 pints) 2 Motorcraft MERCON t V AT F 4R70W Automatic with 5.0L V8 engine 13.1L (13.9 quarts) 3 5R55E Automatic with 4.0L OHV V6 engine (4x2) 9.3L (9.8 quarts) 3 5R55E Automatic with 4.0L OHV V6 engine (4x4) 9.5L (10.0 quarts) 3 5R55E Aut[...]

Fluid Ford Part Name Application Capacity Front axle lubricant Motorcraft SAE 80W -90 Premium Rear Axle Lubricant 4x4 vehicles 1.7L (1.8 quarts) Rear axle lubricant 5 Motorcraft SAE 80W -90 Premium Rear Axle Lubricant Refer to Footnote 6 2.9-3.1L (5.5-5.8 pints) Motorcraft SAE 75W -140 High Performance Synthetic Rear Axle Lubricant Refer to Footnot[...]

6 V ehicles equipped with 4.0L OHV V6 and4.0L SOHC V6 engines may be equipped with a conventional rear axle. Refer to your scheduled maintenance guide for axle fluid change intervals. 7 V ehicles equipped with 4.0L OHV V6 and4.0L SOHC V6 engines and 3.73:1 or 4.10:1 rear axle ratios or with a 5.0L V8 engine require synthetic rear axle lubricant. Re[...]

Item Ford Part Name or equivalent Ford Part Number Ford Specification Engine coolant 1 Ford Premium Engine Coolant E2FZ-19549-AA (in Canada, Motorcraft CXC-8-B) ESE-M97B44-A Engine oil Motorcraft SAE 5W -20 Super Premium Motor Oil XO-5W20-QSP WSS-M2C153-H with API Certification Mark MotorcraftSAE 5W -30 Super Premium Motor Oil XO-5W30-QSP WSS-M2C15[...]

Item Ford Part Name or equivalent Ford Part Number Ford Specification W indshield washer fluid Ultra-clear W indshield W asher Concentrate C9AZ-19550-AC ESR-M17P5-A 1 DO NOT USE Ford Extended Life Engine Coolant F6AZ-19544-AA, meeting Ford specification WSS-M97B44-D (orange in color) Refer to Adding engine coolant, in the Maintenance and Care chapt[...]

ENGINE DATA Engine 4.0L OHV V6 engine 4.0L SOHC V6 engine 5.0L V8 engine Cubic inches 245 245 302 Required fuel 87 octane 87 octane 87 octane Firing order 1-4-2-5-3-6 1-4-2-5-3-6 1-3-7-2-6-5-4-8 Spark plug gap 1.3-1.4 mm (0.052-0.056 inch) 1.3-1.4 mm (0.052-0.056 inch) 1.3-1.4 mm (0.052-0.056 inch) Ignition system EDIS EDIS EDIS Compression ratio 9[...]

* Height includes roof rack 4 1 3 5 2 Capacities and specifications 273[...]

IDENTIFYING YOUR VEHICLE Certification label The National Highway T raffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’ s side. V ehicle identification number [...]

Ford Extended Service Plan Y ou can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.S.) and Ford of Canada (in Canada). It provides the following: • benefits durin[...]

If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing dealership. 2. If your inquiry or concern remains unresolved, contact the Sales Manager or Service Manager at the dealership. 3. If the inquiry or concern can[...]

In the United States: Ford Motor Company Customer Assistance Center 16800 Executive Plaza Drive P .O. Box 6248 Dearborn, Michigan 48121 1-800-521-4140 (TDD for the hearing impaired: 1-800-232-5952) In Canada: Customer Assistance Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) In order to h[...]

THE DISPUTE SETTLEMENT BOARD (U.S. only) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes • available free to owners and lessees of qualifying Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligib[...]

Board membership The Board consists of: • three consumer representatives • a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their busin[...]

Y ou will receive a letter of explanation if your application does not qualify for Board review . Oral presentations If you would like to make an oral presentation, indicate YES to question #6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whethe[...]

UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory , Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor V ehicle [...]

If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMP ANY WORLDWIDE DIRECT MARKET OPERA TIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S[...]

Ford Metal Surface Cleaner Ford Multi-Purpose Cleaner* Motorcraft Car W ash Concentrate Motorcraft Carlite Glass Cleaner Ford Spot and Stain Remover* Ford Super Premium T ire and T rim Dressing Ford T riple Clean Ford Ultra-Clear Spray Glass Cleaner (not available in Canada) * May be sold with the Motorcraft name FORD ACCESSORIES FOR YOUR VEHICLE A[...]

T ravel equipment Automatic headlamps with daytime running lights (DRL) Daytime running lights (DRL) Factory luggage rack adaptors Fog lights Framed luggage covers Heavy-duty battery Home link visor Inside mirror , electrochromic compass (with and without temperature display) Luggage/cargo basket Neutral towing transfer case kit (Explorer 4.0L only[...]

Front end covers (full and sport) Hood deflectors Locking gas cap Lubricants and oils Molded splash guards Molded vinyl floor mats Rear air deflectors Rear decklid spoilers Side window air deflectors T ouch-up paint Universal floor mats For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to y[...]

ORDERING ADDITIONAL OWNER’S LITERA TURE T o order the publications in this portfolio: Make checks payable to: HELM, INCORPORA TED P .O. Box 07150 Detroit, Michigan 48207 For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST , for credit card holders only Obtaining a French owner ’ s guide French[...]

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company . If NHTSA receives similar complaints, it may open an investigation, and i[...]

A Air bag supplemental restraint system ........ 135–136, 140 and child safety seats ............ 137 description ......................136, 140 disposal .................................... 143 driver air bag ..................138, 141 indicator light ........... 10, 139, 142 operation ......................... 138, 141 passenger air bag .......[...]

Certification Label ....................274 Child safety restraints .............. 143 child safety belts .................... 143 Child safety seats ......................144 in front seat ............................ 146 in rear seat .............................. 146 tether anchorage hardware ...148 Cleaning your vehicle ............... 259 engi[...]

Driving under special conditions .......................... 172, 175 mud .......................... 171–172, 174 sand ................................. 172, 174 snow and ice ...171, 173–174, 176 through water .........172, 174, 179 E Emergencies, roadside jump-starting .......................... 204 Emission control system .......... 252 Engine[...]

odometer ................................... 15 speedometer ............................. 14 tachometer ................................ 15 trip odometer ............................ 15 GA WR (Gross Axle W eight Rating) ....................................... 176 calculating ............................... 178 definition ...........................[...]

fog lamps ................................... 21 headlamps ................................. 21 headlamps, flash to pass .......... 22 instrument panel, dimming .....22 replacing bulbs ............... 253–257 Lane change indicator (see T urn signal) ........................ 81 Liftgate ...................................... 105 Lights, warning an[...]

Preparing to drive your vehicle ............................... 158 R Radio ............................................ 35 Relays ........................................ 191 Remote entry system ....... 107–108 illuminated entry ....................112 locking/unlocking doors .........108 panic alarm ............................. 108 replacement[...]

T ransmission ............................. 159 fluid, checking and adding (automatic) .....................229, 231 fluid, checking and adding (manual) ................................. 234 fluid, refill capacities .............. 266 lubricant specifications .. 269, 272 manual operation .................... 166 T rip odometer .....................[...]

Item Information Required fuel Unleaded fuel only - 87 octane Fuel tank capacity (2 door) 66.2L (17.5 gallons) Fuel tank capacity (4 door) 75.5L (22.5 gallons) 4.0L Engine oil capacity (includes filter change) 4.7L (5.0 quarts). Use Motorcraft SAE 5W -30 Super Premium Motor Oil, Ford specification WSS-M2C153-G. 4.6L Engine oil capacity (includes fi[...]

1 Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter . 2 Ensure the correct automatic transmission fluid is used. T ransmission fluid requirements are indicated on the dipstick or on the dipstick handle. MERCON t and ME[...]