Ford 2002 F-150 manual

Introduction 4 Instrument Cluster 10 W arning and control lights 10 Gauges 16 Entertainment Systems 20 AM/FM stereo cassette 20 AM/FM stereo with CD 26 AM/FM stereo cassette (CD changer compatible) 35 CD changer 48 Climate Controls 54 Heater only 54 Manual heating and air conditioning 55 Electronic automatic temperature control 58 Lights 64 Headlam[...]

Locks and Security 101 Keys 101 Locks 101 Anti-theft system 102 Seating and Safety Restraints 1 13 Seating 113 Safety restraints 122 Air bags 135 Child restraints 144 Driving 159 Starting 159 Brakes 164 T ransmission operation 169 V ehicle loading 190 T railer towing 192 Roadside Emergencies 203 Getting roadside assistance 203 Hazard flasher switch[...]

Customer Assistance 227 Reporting safety defects (U.S. only) 235 Cleaning 236 Maintenance and Specifications 244 Engine compartment 246 Engine oil 249 Battery 253 Fuel information 261 Air filter(s) 279 Part numbers 284 Refill capacities 285 Lubricant specifications 289 Accessories 298 Index 302 All rights reserved. Reproduction by any means, electr[...]

CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemic[...]

SAFETY AND ENVIRONMENT PROTECTION W arning symbols in this guide How can you reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed. W arning sym[...]

Please read the section Air bag in the Seating and safety restraints chapter . Failure to follow the specific warnings and instructions could result in personal injury . Front seat mounted rear facing child or infant seats should NEVER be used in front of a passenger side air bag unless the air bag can be and is turned OFF . Snowplowing Ford recomm[...]

Using your vehicle as an ambulance Do not use this vehicle as an ambulance. Y our vehicle is not equipped with the Ford Ambulance Preparation Package. Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate than other types of vehicles. Before you drive your vehicle, please read this Ow[...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner ’ s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation W arning Child Seat Lower Anchor Child Seat T ether Anchor Brake System Anti-Lock Brake System Brake Fluid - Non-Petroleum Based T raction Control Adv[...]

V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Corr[...]

W ARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster Harley-Davidson instrument cluster W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle ’ s functions. L H L H E F C [...]

Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains on after starting the vehicle, have the respective system inspected immediately . Service engine soon Illuminates briefly to ensure the system is functional. If it comes on after the engine is started, one of the engine ’ s emission control s[...]

Check fuel cap Illuminates when the fuel cap is not installed correctly . Check the fuel cap for proper installation. When the fuel filler cap is properly re-installed, the light(s) will turn off after a period of normal driving. Continuing to operate the vehicle with the check fuel cap light on, or a mis-installed fuel cap can activate the Service[...]

malfunctioned and is disabled, however , the normal brake system will still function unless the brake warning light also remains illuminated and parking brake is off. Refer to Brakes in the Driving chapter for more information. Safety belt Illuminates to remind you to fasten your safety belts. For more information, refer to the Seating and safety r[...]

Low washer fluid (if equipped) Illuminates when the windshield washer fluid is low . Speed control (if equipped) Illuminates when the speed control is activated. T ransmission control indicator light (TCIL) Illuminates when the overdrive function of the transmission has been turned OFF using the T ransmission Control Switch (TCS). Refer to the Driv[...]

Anti-theft system (if equipped) Refer to SecuriLock 娂 passive anti-theft system in the Locks and Security chapter . Four wheel drive low (if equipped) Illuminates when four -wheel drive low is is engaged. If the light continues to flash have the system serviced. Four wheel drive indicator (if equipped) Illuminates when the four -wheel drive is en[...]

GAUGES Standard instrument cluster gauges Optional instrument cluster gauges Harley-Davidson instrument cluster gauges MPH km/h 20 40 60 80 100 140 120 160 30 40 0 10 20 50 60 70 80 90 100 110 130 120 180 200 D BRAKE PR N D 2 CRUISE DOOR AJAR THEFT SERVICE ENGINE SOON LOW FUEL RPMX1000 L H L H E F C H SELECT/RESET PREMIUM UNLEADED FUEL ONLY Instrum[...]

Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “ H ” and “ C ” ). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let [...]

Battery voltage gauge Indicates battery voltage. If the pointer moves and stays outside the normal operating range, have the vehicle ’ s electrical system checked as soon as possible. Fuel gauge Displays approximately how much fuel is in the fuel tank. The fuel gauge may vary slightly when the vehicle is in motion or on a grade. When refueling th[...]

T rip odometer Registers the kilometers (miles) of individual journeys. Press and release the reset button until a ’ T ’ appears in the display (this represents the trip mode). Press and hold the button for three seconds to reset. T achometer (if equipped) Indicates the engine speed in revolutions per minute. Driving with your tachometer pointe[...]

AM/FM STEREO CASSETTE V olume/power control Press the control to turn the audio system on or off. T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “ nominal ” listening level when the ignition switch is turned back on. SCAN BASS TREB BAL FADE[...]

Bass adjust The bass adjust control allows you to increase or decrease the audio system ’ s bass output. T reble adjust The treble adjust control allows you to increase or decrease the audio system ’ s treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers Speaker fade adjust Speaker[...]

Seek function The seek function control works in radio mode. Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. Scan function The scan function works in radio mode. Scan function in radio mode Press the SCAN control to hear a brief s[...]

Setting memory preset stations 1. Select the frequency band with the AM or the FM select control. 2. Select a station. Refer to T une adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. Setting th[...]

When in clock mode, the media information will display for 10 seconds, when the radio is turned on, and then revert to clock information. Any time that the media is changed, (new radio station, etc.), the media information will again display for 10 seconds before reverting back to the clock. In media mode, the media information will always be displ[...]

In order to ensure proper operation of the AMS feature, the tape MUST have a blank section of at least four seconds duration between programs. Rewind The rewind control works in tape mode. T o rewind in tape mode, press the REW control. Fast forward The fast forward control works in tape mode. T o fast forward in tape mode, press the FF control. In[...]

PREMIUM AM/FM STEREO/SINGLE CD RADIO Y our audio system is equipped with selective lighting, a unique lighting strategy . This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off. Those controls which have a funct[...]

T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “ nominal ” listening level when the ignition switch is turned back on. Speed sensitive volume (if equipped) W ith this feature, radio volume changes automatically and slightly with vehicle spe[...]

T reble adjust The treble adjust control allows you to increase or decrease the audio system ’ s treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Seek function The seek function control works [...]

three seconds or more and you press , the CD changer will replay that selection from the beginning. • Press to seek forward to the next track of the current disc. After the last track has been completed, the first track of the current disc will automatically replay . Scan function The scan function works in radio, CD and CD changer mode (if equip[...]

2. Select a station. Refer to T une adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. Autoset memory preset Autoset allows you to set strong radio stations without losing your original manually [...]

Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly . • Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold for quick movement. Tune adjust for CD cha[...]

Rewind The rewind control works in CD mode. • In CD mode, pressing the REW control for less than three seconds results in slow rewind. Pressing the control for more than three seconds results in fast rewind. Fast forward The fast forward control works in CD mode. • In CD mode, pressing the control for less than three seconds results in slow for[...]

Mute mode Press the control to mute the playing media. Press the control again to return to the playing media. Radio data system (RDS) feature This feature allows your audio system to receive station identification or program type from RDS-equipped FM radio station. The Federal Communications Commission (FCC) and the Canadian Radio and T elecommuni[...]

• Use the SEL control to select the program type. W ith the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: • Classic • Country • Info • Jazz • Oldies • R&B • Religious • Rock • Soft • To p 4 0 Show • W ith RDS activated, press the RDS control until SHOW is display[...]

PREMIUM AM/FM STEREO/CASSETTE (CD CHANGER COMPATIBLE) Y our audio system is equipped with selective lighting, a unique lighting strategy . This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off. Those controls w[...]

If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “ nominal ” listening level when the ignition switch is turned back on. Speed sensitive volume (if equipped) W ith this feature, radio volume automatically changes slightly with vehicle speed to compensate for road and wind noise. The re[...]

T reble adjust The treble adjust control allows you to increase or decrease the audio system ’ s treble output. Press the TREB control. Use the SEL control to increase or decrease the amount of treble. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control. Use the SEL control [...]

Seek function in tape mode • Press to listen to the previous selection on the tape or return to the beginning of the current selection. • Press to listen to the next selection on the tape. Seek function for CD changer • Press to seek to the previous track of the current disc. If a selection has been playing for three seconds or more and you p[...]

AM/FM select The AM/FM select control works in radio, tape and CD modes (if equipped). AM/FM select in radio mode The AM/FM control allows you to select AM or FM frequency bands. Press the control to toggle between AM, FM1 or FM2 memory preset stations. AM/FM select in tape mode Press this control to stop tape play and begin radio play . AM/FM sele[...]

Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all[...]

Tune adjust for CD changer • Press to select the previous disc in the CD changer . (Play will begin on the first track of the disc unless the CD changer is in shuffle mode.) Refer to Shuffle feature for more information. Hold the control to continue reversing through the discs. • Press to select the next disc in the CD changer . Hold the contro[...]

• In CD mode, pressing the control for less than three seconds results in slow forward action. Pressing the control for more than three seconds results in fast forward action. T ape direction select Press SIDE 1 – 2 to play the alternate side of a tape. Eject function Press the control to stop and eject a tape. Dolby 姞 noise reduction Dolby ?[...]

Shuffle feature The shuffle feature operates in CD mode and plays all tracks on the current disc in random order . If equipped with the CD changer , the shuffle feature continues to the next disc after all tracks are played. Press the SHUFFLE control to start this feature. Random order play will continue until the SHUFFLE control is pressed again. [...]

• Use the SEL control to select ON or OFF . With the feature on, use the SEEK or SCAN control to find a radio station broadcasting a traffic report (if it is broadcasting RDS data). T raffic information is not available in most U.S. markets. Program type • Press the RDS control until the FIND program type is displayed. • Use the SEL control t[...]

• Use the SEL control to select TYPE (the display shows the program type), NAME (the display shows the call letters of the station) or NONE. HARLEY-DAVIDSON REAR SEAT CONTROLS (IF EQUIPPED) The rear seat controls allow the middle seat passengers to operate the radio, tape, CD or CD changer (if equipped). T o turn on the rear seat controls, press [...]

ADJUSTING THE VOLUME Press the + control to increase volume. Press the - control to decrease volume. From the rear seat controls, volume control can be set no higher than the current radio setting unless the speakers are turned off. Refer to T urning speakers on and off. T URNING THE SPEAKERS ON AND OFF Press to turn all speakers on or off. USING H[...]

MODE SELECT Push the MODE control to toggle between AM, FM1, FM2, tape, CD or CD changer (if equipped). MEMORY PRESET CONTROL Push the MEMORY control successively to allow rear seat passengers to scroll through the 6 memory presets in AM, FM1 or FM2. Push the MEMORY control in CD changer mode (if equipped) to advance to the next disc. SEEK FUNCTION[...]

CD CHANGER (IF EQUIPPED) The CD changer is in one of the following locations: • behind the passenger ’ s seat (Regular Cab only) • in the center console (SuperCab/SuperCrew with Captain ’ s chairs) • under the rear bench on the driver ’ s side (see instructions below) (SuperCab with bench seats) • in the stowage bin on the passenger ?[...]

If you pull too hard on the disc holder , the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine while pressing on the lever (A). 5. Line up the CD with the groove of the disc holder . Ensure that the label on the CD faces downwards. 6. Press in on the disc holder until it locks sec[...]

1. The holders DO NOT pull out. Load the discs into the magazine slots (numbered 1 through 6 on the window) one at a time with labeled surfaces upward. 2. Start with the bottom slot number 1. 3. Insert the loaded magazine into the CD changer with the arrow on the top of the magazine pointing toward the changer . T o remove discs: 1. Slide the corre[...]

T ROUBLESHOOTING THE CD CHANGER (IF EQUIPPED) The laser beam used in the compact disc player is harmful to the eyes. Do not attempt to disassemble the case. If sound skips: • Y ou may be traveling on a rough road, playing badly scratched discs or the disc may be dirty . Skipping will not scratch the discs or damage the player . If your changer do[...]

CLEANING CASSETTE PLAYER (IF EQUIPPED) Clean the tape player head with a cassette cleaning cartridge after 10 to 12 hours of play in order to maintain the best sound and operation. CASSETTE AND CASSETTE PLAYER CARE • Use only cassettes that are 90 minutes long or less. • Do not expose tapes to direct sunlight, high humidity , extreme heat or ex[...]

• Station overload. W eak signals are sometimes captured by stronger signals when you pass a broadcast tower . A stronger signal may temporarily overtake a weaker signal and play while the weak station frequency is displayed. The audio system automatically switches to single channel reception if it will improve the reception of a station normally[...]

HEATER ONLY SYSTEM (IF EQUIPPED) Fan speed control Controls the volume of air circulated in the vehicle. T emperature control knob Controls the temperature of the airflow inside the vehicle. On heater -only systems, the air cannot be cooled below the outside temperature. Mode selector control Controls the direction of the airflow to the inside of t[...]

• T o reduce humidity buildup inside the vehicle, do not drive with the climate control system in the OFF position. • Under normal weather conditions, your vehicle ’ s climate control system should be left in any position other than OFF position when the vehicle is parked. This allows the vehicle to “ breathe ” through the outside air inl[...]

T emperature control knob Controls the temperature of the airflow inside the vehicle. Mode Selector Control Controls the direction of the airflow to the inside of the vehicle. The air conditioning compressor can operate in all modes except P ANEL and FLOOR. However , the air conditioning will only function if the outside temperature is about 6 ° C[...]

• FLOOR – Allows for maximum heating by distributing outside air through the floor ducts. However , the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode. • FLR & DEF – Distributes outside air through the windshield defroster ducts and the floor ducts. Heating and air conditi[...]

• Do not put objects under the front seat which may interfere with the airflow to the rear seats (if equipped). • Remove any snow , ice or leaves from the air intake area (at the bottom of the windshield and underneath the hood). • Do not place objects over the defroster outlets. These objects can block airflow and reduce visibility through y[...]

T urning the EA TC system off Press OFF . The outside temperature function will continue to operate until the ignition is turned off. Automatic operation Press AUTOMA TIC and select the desired temperature. The selected temperature and the word AUTO will appear in the display window . The EA TC system will either heat or cool to achieve the selecte[...]

T o control the temperature, select any temperature between 18 ° C (65 ° F) and 29 ° C (85 ° F) by pressing the blue (cooler) or red (warmer) buttons. For continuous maximum cooling, push the blue button until 16 ° C (60 ° F) is shown in the display window . The EA TC will continue maximum cooling (disregarding the displayed temperature) unti[...]

The display will show to indicate manual fan operation. T o return to automatic fan operation, press AUTOMA TIC. Manual override controls The manual override controls allow you to determine where airflow is directed. T o return to full automatic control, press AUTOMA TIC. The air conditioning compressor can operate in all modes except FLOOR and VEN[...]

in this mode. The air will be heated or cooled based on the temperature selection. For added customer comfort, the air distributed through the floor ducts will be slightly warmer than the air sent to the windshield defroster ducts. If the temperature is about 6 ° C (43 ° F) or higher , the air conditioner will automatically dehumidify the air to [...]

• T o reduce humidity buildup inside the vehicle in cold weather conditions, don ’ t drive with the climate control system in the OFF or MAX A/C position. • T o reduce humidity buildup inside the vehicle in warm weather conditions, don ’ t drive with the climate control system in the OFF position. • Under normal weather conditions, your v[...]

HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to turn on the headlamps. Autolamp control (if equipped) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system also kee[...]

Daytime running lamps (DRL) (if equipped) T urns the headlamps on with a reduced output. T o activate: • the ignition must be in the ON position and • the headlamp control is in the OFF , parking lamp or autolamp position. Always remember to turn on your headlamps at dusk or during inclement weather . The Daytime Running Lamp (DRL) system does [...]

P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable switches in the vehicle during headlamp and parklamp operation. Move the control to the full upright position, past detent, to turn on the interior lamps. Move the control to the full down position, past detent, to prevent the interior lights from illumina[...]

INTERIOR LAMPS Map lamps T o turn on the map lamps, press the control next to each lamp. If equipped with a moon roof, the map lamps are located on the moon roof control panel. Press the control next to the map lamp to illuminate the lamp. Rear dome lamp (if equipped) The dome lamp lights when the control is in the DOOR (left) position and: • any[...]

Courtesy/reading lamps The courtesy lamp lights when: • any door is opened. • the instrument panel dimmer switch is held up until the courtesy lamps come on. • the remote entry controls are pressed and the ignition is OFF . The reading lamps can be turned on by pressing the rocker controls next to each lamp. Rear door lamps (if equipped) The [...]

Using the right bulbs Replacement bulbs are specified in the chart below . Headlamp bulbs must be marked with an authorized “ D.O.T . ” for North America and an “ E ” for Europe to assure lamp performance, light brightness and pattern and safe visibility . The correct bulbs will not damage the lamp assembly or void the lamp assembly warrant[...]

6. Disconnect the electrical connector from the bulb by pulling rearward. 7. Remove bulb retainer ring by turning it counterclockwise, then slide the ring off the plastic base. 8. W ithout turning, carefully pull bulb assembly out of headlamp assembly and replace. Handle a halogen headlamp bulb carefully and keep out of children ’ s reach. Grasp [...]

Replacing front parking lamp/turn signal bulbs 1. Remove screw from the lamp assembly . 2. Disengage lamp assembly (it has a snap fit) by pulling straight forward. 3. Remove bulb socket from the parking lamp assembly by turning it counterclockwise. 4. Pull bulb straight out of socket and press in the new bulb. 5. Install the bulb socket into the la[...]

Replacing tail/brake/turn signal/backup lamp bulbs The tail/brake/turn signal and backup lamp bulbs are located in the tail lamp assembly , one just below the other . Follow the same steps to replace either bulb: 1. If equipped, remove tail lamp covers. 2. Open the liftgate to expose the lamp assembly screws. 3. Remove the two bolts from the tail l[...]

Replacing foglamp bulbs (if equipped) 1. Remove the bulb socket from the foglamp by turning counterclockwise. 2. Disconnect the electrical connector from the foglamp bulb. 3. Connect the new foglamp bulb to the electrical connector . 4. Install the bulb socket in the foglamp by turning clockwise. Replacing signal mirror lamp bulbs (if equipped) For[...]

WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals. Push (tap) the end of the stalk briefly for a single swipe (no wash). Pu[...]

1. Pull the wiper arm away from the windshield and lock into the service position. 2. T urn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 3. Attach the new wiper to the wiper arm and press it into place until a click is heard. [...]

ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on the visor mirror lamps. OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle ’ s overhead console will vary according to your option package. Storage compartment (if equipped) Press the OPEN control to open the storage compartment. The door will open slightly and can[...]

1. Remove the storage clip from the door . 2. Place V elcro hook onto side of aftermarket transmitter opposite of actuator control. 3. Place the transmitter into storage compartment, control down. 4. Place the provided height adaptors onto the back of the GARAGE control as needed. 5. Press the GARAGE control to activate the transmitter . Driver Con[...]

Electronic compass/temperature display (if equipped) Outside air temperature The outside temperature display is contained in the overhead console unless the vehicle is equipped with an EA TC system. Refer to Electric automatic temperature control in the Climate controls chapter . The temperature display can be turned off and on by pressing the SELE[...]

Compass zone adjustment 1. Determine which magnetic zone you are in by referring to the zone map. 2. T urn the ignition to the ON position. 3. Press and hold the SELECT control until V AR appears in the display , then release. The display should show the current zone number . 4. Press the SELECT control until the desired zone number appears. The di[...]

AUXILIARY POWER POINT Power outlets are designed for accessory plugs only . Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty . The auxiliary power point is located on the instrument panel. Do not plug optional electrical accessories into the cigarett[...]

• Rear audio controls • Power point Use only soft cups in the cupholder . Hard objects can injure you in a collision. OVERDRIVE CONTROL Activating overdrive (Overdrive) is the normal drive position for the best fuel economy . The overdrive function allows automatic upshifts and downshifts through all available gears. Deactivating overdrive Pres[...]

POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. • Press the bottom portion of the rocker switch to open. One touch down • Press AUTO completely down and release quickly . The driver ’ s window will open fully . Depress again to stop window opera[...]

MIRRORS Automatic dimming rear view mirrors (if equipped) Y our vehicle is equipped with an inside rear view mirror with an auto-dimming function. The electronic day/night mirror will change from the normal state to the non-glare state when bright lights (glare) reach the inside rear view mirror . When the inside rear view mirror detects bright lig[...]

2. Move the control in the direction you wish to tilt the mirror . 3. Return to the center position to lock mirrors in place. 4. Adjust spotter mirrors (if equipped) manually . Signal mirrors (if equipped) When the turn signal is activated, the outer portion of the appropriate mirror housing will blink red. This provides an additional warning to ot[...]

The adjustment allows for approximately 76 mm (3 inches) of maximum travel. Never adjust the accelerator and brake pedal with feet on pedals or while the vehicle is moving. SPEED CONTROL (IF EQUIPPED) T o turn speed control on • Press ON. V ehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not shift[...]

T o set a speed • Press SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal. Speed control cannot reduce the vehicle speed if it increases [...]

T o set a lower set speed • Press and hold COAST . Release the control when the desired speed is reached or • Press and release COAST to operate the T ap-Down function. Each press will decrease the set speed by 1.6 km/h (1 mph) or • Depress the brake pedal. When the desired vehicle speed is reached, press SET ACCEL. T o disengage speed contro[...]

• Depress the clutch pedal (if equipped). Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. T o return to a previously set speed • Press RES. For RES to operate, the vehicle speed must be faster than 48 km/h (30 mph). Indicator light This light comes on[...]

ONE-TOUCH MOON ROOF (IF EQUIPPED) • T o open, press and release the rear portion of the moon roof control. • T o close, press and hold (as desired) the front portion of the moon roof control. • T o halt motion at any point during one-touch opening, press the control a second time. • T o tilt into the vent position (when the glass panel is c[...]

Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.e. new HomeLink 威 equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, the programmed Homelink 威 Universal T ransceiver buttons be erased for security purposes, refer to Programming in this section. Programmin[...]

device should activate when the HomeLink 威 button is pressed and released. Note: T o program the remaining two HomeLink 威 buttons, begin with step 2 in the “ Programming ” section — do not repeat step 1. If the red light blinks rapidly for two seconds and then turns to a continuous red, proceed with steps 6 through 8 to complete programmi[...]

Erasing HomeLink 姞 buttons T o erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink 威 buttons until the red indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds. HomeLink 威 is now in the train (or learning) mode and can be [...]

seconds ( “ cycle ” ) your hand-held transmitter until the frequency signal has been accepted by the HomeLink 威 . The red indicator light will flash slowly and then rapidly after HomeLink 威 accepts the radio frequency signal. • Proceed with step 4 in the “ Programming ” section. Operating T ravelNote 姞 T ravelNote 威 records and st[...]

T o delete a message: 1. Press and release the DEL button while listening to a message or shortly after . The indicator light will flash green twice. 2. T o delete all recorded messages, simultaneously press and release the PLA Y and REC buttons at the same time. The indicator light will flash green twice. If the DEL button is inadvertently pressed[...]

T AILGATE REMOVAL Y our tailgate is removable to allow more room for loading. 1. Lower the tailgate. 2. Use a screwdriver to pry the spring clip (on each connector) past the head of the support screw . Disconnect cable. 3. Disconnect the other cable. 4. Lift tailgate to a 45 degree angle. 5. Lift right side off of its hinge. 6. Lift left side off o[...]

4. Evenly push down on the extender and push the round knobs in on each side locking it in place. Green markings on the shaft indicate the locked position. The locking clip screws below the middle bar can be tightened counterclockwise for extra security . Note: If the red marking on the shaft is visible, the bed extender is not locked or properly s[...]

T ONNEAU COVER (IF EQUIPPED) The tonneau cover has been designed to maximize fuel economy and should be fully installed whenever possible. The cover can be rolled up and stowed behind the cab, or removed completely from the vehicle. • T o avoid damage to the cover , do not operate the vehicle unless the cover is fully installed, or securely stowe[...]

4. Starting from the opposite side of the vehicle, pull cover away from the side rail and roll the cover from rear to front. 5. Secure the cover behind the cab with two straps. The cover may be removed from the vehicle by sliding it sideways out of the front rail. Driver Controls 98[...]

Flareside only: • Remove two cross bars from pickup box by pushing towards either side to release tension. • Lower tailgate, depress the levers on each side of the rear rail and remove rear rail from pickup box. Styleside only: • Remove three cross bars from pickup box by pushing towards either side to release tension. Stow the cross bars in [...]

HARD TONNEAU COVER (IF EQUIPPED) The tonneau cover has been designed to maximize fuel economy . • T o avoid damage to the cover , do not operate the vehicle unless the cover is fully secured. T o open the cover: • Unlock the cover (with the key) and lift the cover up for access to the pickup box. T o close the cover: • Close the cover on pick[...]

KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer . Y ou should always carry a second key with you in a safe place in case you require it in an emergency . Refer to SecuriLock 娂 Passive Anti-Theft System for more information. POWER DOOR LOCKS (IF EQUIPPED) If the door does not unlock[...]

INTERIOR TONNEAU COVER RELEASE (IF EQUIPPED) Y our vehicle is equipped with a mechanical interior tonneau cover release handle that provides a means of escape for children and adults in the event they become locked inside the pickup box. Adults are advised to familiarize themselves with the operation and location of the release handle. T o open the[...]

Changes or modifications not expressly approved by the party responsible for compliance could void the user ’ s authority to operate the equipment. Y our vehicle is equipped with a remote entry system which allows you to: • unlock the vehicle doors without a key . • lock all the vehicle doors without a key . • activate the personal alarm. D[...]

Locking the doors Press this control to lock all doors. T o confirm doors are closed and locked, press this control a second time within three seconds. The door(s) will lock again, the horn will chirp once and the lamps will flash. If any of the doors are open or ajar , the horn will make two quick chirps, reminding you to properly close the doors.[...]

be up to 10 meters (33 feet) away from your vehicle. A decrease in operating range can be caused by the following factors: • W eather conditions • Nearby radio towers • Structures around the vehicle • Other vehicles parked next to the vehicle T o replace the battery: 1. T wist a thin coin between the two halves of the transmitter near the k[...]

T o program the transmitters yourself: • Place the key in the ignition and turn from 2 (LOCK) to 3 (OFF) and cycle between 3 (OFF) and 4 (ON) eight times in rapid succession (within 10 seconds) with the eighth turn ending in the 4 (ON) position. The doors will lock/unlock to confirm that programming mode has been entered. • W ithin 20 seconds, [...]

• the brake is depressed, • the ignition is in the RUN position and the vehicle is traveling more than 8 km/h (5 mph). Relock The autolock feature repeats when: • any door is opened then closed while the ignition is in the RUN position, and • the vehicle is traveling more than 8 km/h (5 mph). Deactivating/activating the autolock feature Bef[...]

When pressing the controls on the keyless entry keypad, press the middle of the controls to ensure a good activation. This system will disable the power door lock controls. These will not work until the vehicle is disarmed. Programming your own personal entry code T o program your own code: 1. Enter factory set code (keypad will illuminate when pre[...]

The keyless entry pad is disabled for 1 minute after 7 unsuccessful attempts at entering a valid key code. The keypad will flash during this 1 minute mode. However , the 7/8 and 9/0 controls will still lock the vehicle. Anti-scan will be turned off after: • one minute of keypad inactivity . • the remote entry transmitter UNLOCK button is presse[...]

THEFT INDICATOR The theft indicator is the flashing red indicator located on the dash panel. • When the ignition is in the OFF position, the indicator will flash once every 2 seconds to indicate the SecuriLock 娂 system is functioning as a theft deterrent. • When the ignition is in the ON position, the indicator will glow for 3 seconds to indi[...]

• A second key on the same key ring as the coded key If any of these items are present, you need to keep these objects from touching the coded key while starting the engine. These objects and devices cannot damage the coded key , but can cause a momentary “ no start ” condition if they are too close to the key during engine start. If a proble[...]

1. Insert the first previously programmed coded key into the ignition and turn the ignition from 1 (OFF) to 3 (ON) (maintain ignition in 3 (ON) for at least one second, but no more than ten seconds). 2. T urn ignition to 1 (OFF) then 2 (ACC) and remove the first coded key from the ignition. 3. W ithin ten seconds of removing the first coded key , i[...]

SEA TING Adjustable head restraints (if equipped) Y our vehicle ’ s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. T o properly adjust your head restraints, lift the head restraint so that it is located directly behind [...]

Full bench seat (if equipped) • Lift the track release bar to move the seat forward or backward. Ensure that the seat is relatched into place. • Pull up on the release lever located at the bottom of the seatback to quickly fold the seatback forward. 60/40 split bench seat (if equipped) • Lift the release bar to move the seat forward or backwa[...]

Captain ’ s chair (if equipped) • Lift the track release bar to move the seat forward or rearward. Make sure that the seat is relatched into place. • Pull the release lever handle located on the side of the seat up to move the seat back forward or backward. • Push down the release lever (if equipped) located at the bottom of the seatback to[...]

Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Using the manual lumbar support T urn the lumbar support control toward the front of vehicle to move the lumbar support forward for more direct support. T urn the lumbar support control toward the rear of vehicle to move the lumbar support back for less direct support. [...]

Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can cause an occupant to slide under the seat ’ s safety belt, resulting in severe personal injuries in the event of a collision. The control is located on the outboard side of the seat cushion. Y our vehicle will only be equippe[...]

• T ype B Press the control to move the seat forward, backward, up or down. • T ype A • T ype B Heated seats (if equipped) T o operate the heated seats: • Push control located on the side of the seat to activate. • Push again to deactivate. The indicator light on the control will illuminate when activated. REAR SEATS Folding up the rear s[...]

1. Pull control to release seat cushion. 2. Rotate seat cushion up until it locks into vertical storage position. Returning the seat to seating position Always be sure that the seat is in a latched position, whether the seat is occupied or empty . If not latched, the seat may cause injury during a sudden stop. 1. Pull control on the side of the sea[...]

2. Pull control to release seat. 3. Pull seatback toward front seat and down into load floor position. 4. Make sure seat is pushed all the way down and locks into position. Returning the seat to seating position Always be sure that the seat is in a latched position, whether the seat is occupied or empty . If not latched, the seat may cause injury d[...]

1. Pull control on the side of the seat to release seat cushion from the load floor position. 2. Lift seatback up until it locks into vertical position. 3. Return the head restraint to its original position. If the head restraint is inserted backwards, it may lock and not be removable by using the release button. If this happens use a stiff piece o[...]

Using the armrest (if equipped) Push the release control to move the armrest up or down. SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. T o reduce the risk of injury , make sure children sit where they can be properly restrained. Never let a passenger h[...]

In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt. Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair . 1) Use the shoulder belt on the outside shoulder only . Never wear the shoul[...]

• Rear seats (if equipped) 2. T o unfasten, push the release button and remove the tongue from the buckle. • Front seats • Rear seats (if equipped) The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes describ[...]

response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply , or the vehicle receives an impact of approximately 8 km/h (5 mph) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers. The front seat belt system can also be made to lock manually by quickly p[...]

• Rear seats (if equipped) 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Disconnect the combination lap/shoulder [...]

BEL T AND RETRACTOR ASSEMBL Y MUST BE REPLACED if the seat belt assembly “ automatic locking retractor ” feature or any other seat belt function is not operating properly when checked according to the procedures in W orkshop Manual. Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions. Safety belt p[...]

• Regular Cab/4 – door SuperCrew • 4 – door SuperCab (Bench seats only) Seating and Safety Restraints 128[...]

T o lower the shoulder belt height, push the button and slide the height adjuster down. T o raise the height of the shoulder belt, slide the height adjuster up. Pull down on the height adjuster to make sure it is locked in place. Position the safety belt height adjusters so that the belt rests across the middle of your shoulder . Failure to adjust [...]

Shorten and fasten the belt when not in use. • 2nd row center seating position (SuperCrew) The lap belt will adjust automatically . T o fasten, grasp the tongue, and with a continuous motion, pull out enough webbing to buckle the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). If you did not pull ou[...]

BeltMinder (if equipped) The BeltMinder feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders to the driver that the driver ’ s safety belt is unbuckled by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster . If... Then... The driver ?[...]

Reasons given... Consider ... “ Crashes are rare events ” 36700 crashes occur every day . The more we drive, the more we are exposed to “ rare ” events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our lifetime. “ I ’ m not going far ” 3o f4 fatal crashes occur within 25 miles of home. “ Belts are [...]

Reasons given... Consider ... “ I have an air bag ” Air bags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. “ I ’ d rather be thrown clear ” Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, [...]

BeltMinder activation and deactivation procedure 1. T urn the ignition switch to the RUN (or ON) position. (DO NOT ST ART THE ENGINE.) 2. W ait until the safety belt warning light turns off. (Approximately 1 – 2 minutes.) • Steps 3 – 5 must be completed within 60 seconds or the procedure will have to be repeated. 3. Buckle then unbuckle the s[...]

the label. Also, use the safety belt extension only if the safety belt is too short for you when fully extended. Do not use extensions to change the fit of the shoulder belt across the torso. Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sur[...]

collision including information about the air bag system and impact severity . This information will assist Ford Motor Company in servicing the vehicle and in helping to better understand real world collisions and further improve the safety of future vehicles. Important supplemental restraint system (SRS) precautions The supplemental restraint syst[...]

Do not put anything on or over the air bag module. Placing objects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causing serious injury . Do not attempt to service, repair , or modify the air bag supplemental restraint systems or its fuses. See your Ford or Lincoln Mercury deal[...]

How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather , it means the forces were not of the type sufficient to cause activa[...]

If the air bag has deployed, the air bag will not function again and must be replaced immediately . If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision. The SRS consists of: • driver and passenger air bag modules (which include the inflators and air bags), • one or more impact and safing sensors, [...]

Disposal of air bags and air bag equipped vehicles (including pretensioners) For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel. Passenger air bag ON/OFF switch (if equipped) An air bag ON/OFF switch has been installed in this vehicle. Before [...]

If the OFF light fails to illuminate when the passenger air bag switch is in the OFF position and the ignition switch is in ON, have the passenger air bag switch serviced at your Ford or Lincoln-Mercury dealer immediately . In order to avoid inadvertent activation of the switch, always remove the ignition key from the passenger air bag ON/OFF switc[...]

The safety belts for the driver and right front passenger seating positions have been specifically designed to function together with the air bags in certain types of crashes. When you turn OFF your air bag, you not only lose the protection of the air bag, you also may reduce the effectiveness of your safety belt system, which was designed to work [...]

• the infant has a medical condition which, according to the infant ’ s physician, makes it necessary for the infant to ride in the front so that the driver can constantly monitor the child ’ s condition. 2. Child age 1 to 12. A child age 1 to 12 must ride in the front seat because: • the vehicle has no rear seat; • although children ages[...]

3. Medical condition: A passenger has a medical condition that, according to his or her physician: • poses a special risk for the passenger if the air bag deploys; and • makes the potential harm from the passenger air bag deployment greater than the potential harm from turning OFF the air bag and experiencing a crash without the protection offe[...]

Do not leave children, unreliable adults, or pets unattended in your vehicle. Child booster seats Children outgrow a typical convertible or toddler seat when they weigh 40 pounds and are around 4 years of age. Although the lap/shoulder belt will provide some protection, these children are still too small for lap/shoulder belts to fit properly , whi[...]

T ypes of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt. If a seating position has a low seat back and no head restraint, a backless booster seat may place your child ’ s head (top of ear level)[...]

Follow all instructions provided by the manufacturer of the booster seat. Never put the shoulder belt under a child ’ s arm or behind the back because it eliminates the protection for the upper part of the body and may increase the risk of injury or death in a collision. Never use pillows, books, or towels to boost a child. They can slide around [...]

• Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter . • Use the correct safety belt buckle for that seating position (the buckle closest to the direction the tongue is coming from). • Insert the belt tongue into the proper buckle until you hear a snap and feel it latch. Make sure [...]

Children 12 and under should be properly restrained in the rear seat whenever possible. 1. Position the child safety seat in a seat with a combination lap and shoulder belt. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue throu[...]

4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it. 5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull[...]

8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly tilt the seat forward and back to make sure the seat is securely held in place. T o check this, grab the seat at the belt path and attempt to move it side to side and forward and back. There should be no more than one inch of movem[...]

3. While holding the webbing to prevent it from retracting, route the webbing through the child seat according to the child seat manufacturer ’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the tongue into the correct buckle for that seating position until you hear and feel the buckle engage. Make sure the buckle is latched s[...]

• F150 SuperCab • F150 SuperCrew • F150 SuperCrew with quad buckets T ether strap attachment 1. Position the child safety seat on the seat cushion. 2. Route the child safety seat tether strap over the back of the seat. 3. Locate the correct anchor for the selected seating position. • Y ou may need to pull the seatback forward to access the [...]

before installing the child seat. Refer to the Folding Down The Rear Seats section in this chapter for information on how to operate the rear seats. 4. Clip the tether strap to the anchor as shown. • Front seat (Regular Cab and SuperCab only) • Rear seats ( with quad buckets only) Seating and Safety Restraints 154[...]

• Rear seats (SuperCrew only) If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. 5. Refer to the Installing child safety seats in combination lap and shoulder belt seating positions section of this chapter for further instructions to secure the child safety seat. 6. T ighte[...]

1. Route the tether strap through the loop directly behind the child seat. 2. Attach the strap hook onto the loop behind an adjacent seating position. 3. Install the child safety seat tightly using the safety belts. Follow the instructions in this chapter . 4. T ighten the tether strap according to the child seat manufacturer ’ s instructions. At[...]

Y our vehicle be equipped with LA TCH anchors for child seat installation at the following seating positions: • F150 Regular Cab • F150 Supercab • F150 SuperCrew • F150 SuperCrew with Quad Buckets The anchors on both sides of the center of the SuperCrew rear seat are provided only for child seats at the outboard seats. These anchors are fur[...]

seat. If you install a child seat at the center rear position, use the vehicle lap belt and the top tether anchor . Connectors on the LA TCH child seat and the child seat instructions may use the symbol shown here. Y our vehicle seat may have plain buttons, instead of this symbol, to indicate the location of the LA TCH lower anchors. Never attach t[...]

STARTING Positions of the ignition 1. ACCESSORY , allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. 3. OFF , shuts off the engine and all accessories without locking the steering wheel. This position also a[...]

Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding a[...]

• Make sure the parking brake is set. • Make sure the gearshift is in P (Park). If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Push the clutch pedal to the floor . 3. T urn the key to 4 (ON) without turning the key to 5 (ST ART). 1 2 3 4 5 Driving 161[...]

Make sure the corresponding lights illuminate or illuminate briefly . If a light fails to illuminate, have the vehicle serviced. • If the driver ’ s safety belt is fastened, the light may not illuminate. Starting the engine Note: Whenever you start your vehicle, release the key as soon as the engine starts. Excessive cranking could damage the s[...]

1. T urn the key to 5 (ST ART) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 4 (ON). 2. If the temperature is above – 12 ° C (10 ° F) and the engine does not start within five seconds on the first try , turn the key to OFF , wait 10 seconds and try again. If the engine does not start in [...]

If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately . Do not drive if you smell exhaust fumes. These fumes are harmful and could kill you. Have the exhaust and body ventilation systems checked whenever: • the vehicle is raised for service. • the sound of the exhaust system c[...]

If you are driving down a long or steep hill, shift to a lower gear . Do not apply your brakes continuously , as they may overheat and become less effective. Anti-lock brake system (ABS) This vehicle is equipped with an anti-lock braking system (ABS). A noise from the hydraulic pump motor and pulsation in the pedal may be observed during ABS brakin[...]

W ith the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the brake warning light also remains illuminated with parking brake released. (If your brake warning lamp illuminates, have your vehicle serviced immediately .) Parking brake Apply the parking brake whenever the vehicle is parked. T o set the[...]

Pull the release lever to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy . STEERING Y our vehicle is equipped with power steering. Power steering uses energy from the engine to decrease the driver ’ s effort in steering the vehicle. T o prevent damage to the power steering pu[...]

Extended use of other than the manufacturer ’ s specified size tires on a T raction-Lok rear axle could result in a permanent reduction in effectiveness. This loss of effectiveness does not affect normal driving and should not be noticeable to the driver . T o reduce the risk of injury , never run the engine with one wheel off the ground, such as[...]

AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless the brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the O[...]

If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly . See your dealer or a qualified service technician. Driving with a 4 – speed automatic transmission Understanding gearshift positions T o put your vehicle in gear , start the engine, depress the brake pedal, then move ge[...]

(Overdrive) The normal driving position for the best fuel economy . T ransmission operates in gears one through four . (Overdrive) can be deactivated by pressing the transmission control switch (TCS) on the end of the gearshift lever . The transmission control indicator light (TCIL) (the word OFF) on the end of the gearshift lever will illuminate. [...]

1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive). Selecting 1 (Low) at higher speeds causes the transmission to shift to a lower gear , and will shift to 1 (Low) after vehicle decelerates to the proper speed. Forced Downshifts T o gain acceleration in (Over[...]

1. Make sure the parking brake is fully set. 2. Depress the clutch pedal fully . 3. Put the gearshift lever in neutral. 4. Start the engine and let it idle for a few seconds. 5. Depress the brake pedal. 6. Release the parking brake. 7. Move the gearshift lever to the desired gear . 8. Release the brake pedal. 9. Slowly release the clutch pedal whil[...]

Recommended shift speeds Upshift and downshift according to the following charts for your specific engine/drivetrain combination: • 4.2L V6 engine (4x2 and 4x4) Upshifts when accelerating (recommended for best fuel economy) Shift from: T ransfer case position (if equipped) 2H or 4H 4L 1 - 2 24 km/h (15 mph) 14 km/h (9 mph) 2 - 3 40 km/h (25 mph) [...]

Upshifts when cruising (recommended for best fuel economy) Shift from: T ransfer case position (if equipped) 2H or 4H 4L 1 - 2 16 km/h (10 mph) 6 km/h (4 mph) 2 - 3 34 km/h (21 mph) 16 km/h (10 mph) 3 - 4 51 km/h (32 mph) 21 km/h (13 mph) 4 - D (Overdrive) 72 km/h (45 mph) 27 km/h (17 mph) • 4.6L V8 engine (4x2 with optional rear axle ratio) Upsh[...]

• All applications Maximum downshift speeds 1 Shift from: T ransfer case position (if equipped) 2H or 4H 4L D (Overdrive) - 4 89 km/h (55 mph) 34 km/h (21 mph) 4 - 3 72 km/h (45 mph) 27 km/h (17 mph) 3 - 2 56 km/h (35 mph) 21 km/h (13 mph) 2 - 1 32 km/h (20 mph) 11 km/h (7 mph) 1 Downshift at lower speeds when driving on slippery surfaces. Parkin[...]

4. T urn the ignition key to position 3 (OFF). Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully . Reverse Make sure that your vehicle is at a complete stop before you shift into R (Reverse). Failure to do so may damage the transmission. Put the gearshift in N (Neutr[...]

Removing key from ignition • T urn the ignition key to position 2. • Push the release lever forward and rotate the key towards you and remove. FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this chapter . When four – wheel drive [...]

• 4X4 - momentarily illuminates after the engine is started. Illuminates when 4H (4WD High) is engaged. • LOW RANGE - momentarily illuminates with the key in the ON position and after the engine is started. Illuminates when 4L (4WD Low) is engaged. Using a manual 4WD system (if equipped) 2H (2WD High) – Power to rear axle only . 4H (4WD High)[...]

3. Place the gearshift lever in N (Neutral) (automatic transmission) or depress the clutch (manual transmission). 4. Move the transfer case shift lever through N (Neutral) directly to 4L (4WD Low) and hold the shift lever in 4L (4WD Low) until the transfer case has fully engaged (up to 15 seconds). 5. If the transfer case does not engage into 4L (4[...]

Do not leave the vehicle unattended with the transfer case in the N (Neutral) position. Always set the parking brake fully and turn off the ignition when leaving the vehicle. Using the electronic shift 4WD system (if equipped) Positions of the electronic shift system 2H (2WD High) – Power to rear axle only . 4H (4WD High) – Power delivered to f[...]

3. Place the gearshift in N (Neutral) (automatic transmission) or depress the clutch (manual transmission). 4. Move the 4WD control to the 4H or 4L position. Driving off-road with truck and utility vehicles 4WD vehicles are specially equipped for driving on sand, snow , mud and rough terrain and have operating characteristics that are somewhat diff[...]

• Drive slower in strong crosswinds which can affect the normal steering characteristics of your vehicle. • Be extremely careful when driving on pavement made slippery by loose sand, water , gravel, snow or ice. If your vehicle goes off the edge of the pavement • If your vehicle goes off the edge of the pavement, slow down, but avoid severe b[...]

Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly . See your dealer or a qualified service tec[...]

Parking On some 4WD vehicles, when the transfer case is in the N (Neutral) position, the engine and transmission are disconnected from the rest of the driveline. Therefore, the vehicle is free to roll even if the automatic transmission is in P (Park) or the manual transmission is in gear . Do not leave the vehicle unattended with the transfer case [...]

Mud and water If you must drive through high water , drive slowly . T raction or brake capability may be limited. When driving through water , determine the depth; avoid water higher than the bottom of the hubs (if possible) and proceed slowly . If the ignition system gets wet, the vehicle may stall. Once through water , always try the brakes. W et[...]

slopes or hills . A danger lies in losing traction, slipping sideways and possibly rolling over . Whenever driving on a hill, determine beforehand the route you will use. Do not drive over the crest of a hill without seeing what conditions are on the other side. Do not drive in reverse over a hill without the aid of an observer . When climbing a st[...]

Should you start to slide while driving on snowy or icy roads, turn the steering wheel in the direction of the slide until you regain control. A void sudden applications of power and quick changes of direction on snow and ice. Apply the accelerator slowly and steadily when starting from a full stop. A void sudden braking as well. Although a 4WD veh[...]

Do not use “ aftermarket lift kits ” or other suspension modifications, whether or not they are used with larger tires and wheels. These “ aftermarket lift kits ” could adversely affect the vehicle ’ s handling characteristics, which could lead to loss of vehicle control or rollover and serious injury . T ires can be damaged during off-ro[...]

Any modifications to a vehicle that raise the center of gravity can make it more likely the vehicle will roll over as a result of a loss of control. Ford Motor Company recommends that caution be used with any vehicle equipped with a high load or device (such as ladder racks or pickup box cover). Failure to maintain your vehicle properly may void th[...]

The GVWR is specific to each vehicle and is listed on the Safety Certification Label on the driver ’ s door pillar . • GA WR (Gross Axle W eight Rating): Carrying capacity for each axle system. The GA WR is specific to each vehicle and is listed on the Safety Certification Label on the driver ’ s door pillar . • GCW (Gross Combined W eight)[...]

Always ensure that the weight of occupants, cargo and equipment being carried is within the weight limitations that have been established for your vehicle including both gross vehicle weight and front and rear gross axle weight rating limits. Under no circumstance should these limitations be exceeded. Exceeding any vehicle weight rating limitation [...]

Y our vehicle ’ s load capacity is designated by weight, not by volume, so you cannot necessarily use all available space when loading a vehicle. T owing a trailer places an additional load on your vehicle ’ s engine, transmission, axle, brakes, tires and suspension. Inspect these components carefully periodically during, and after any towing o[...]

Engine Rear axle ratio Maximum GCWR-kg (lbs.) Maximum trailer weight-kg (lbs.) 4.6L 3.55 5216 (11500) 3130 (6900)/ 2994 (6600) 5.4L 3.31 5443 (12000) 3311 (7300) 5.4L 3.55 5897 (13000) 3765 (8300)/ 3628 (8000) 5.4L 3.73 6124 (13500) 3900 (8600) 5.4L 4.10 6803 (15000) 3900 (8600) Engine Rear axle ratio Maximum GCWR-kg (lbs.) Maximum trailer weight-k[...]

Engine Rear axle ratio/tire size - cm (inches) Maximum GCWR-kg (lbs.) Maximum trailer weight-kg (lbs.) 4.6L 3.55/43.2 (17) 4990 (11000) 2858 (6300) 5.4L 3.31/40.6 (16) 5443 (12000) 3266 (7200) 5.4L 3.55/40.6 (16) 5897 (13000) 3720 (8200) 5.4L 3.55/43.2 (17) 5670 (12500) 3493 (7700) 5.4L 3.73/40.6 (16) 6124 (13500) 3810 (8400) SuperCab/Super Crew 4x[...]

Harley-Davidson F-150 4x2 w/automatic transmission Engine Rear axle ratio Maximum GCWR-kg (lbs.) Maximum trailer weight-kg (lbs.) 5.4L Supercharged 3.73 4536 (10000) 2041 (4500) T railer frontal area considerations: • Not to exceed towing vehicle frontal area without Class III trailer towing package • Not to exceed 5.52 square meters (60 square[...]

Safety chains Always connect the trailer ’ s safety chains to the frame or hook retainers of the vehicle hitch. T o connect the trailer ’ s safety chains, cross the chains under the trailer tongue and allow slack for turning corners. If you use a rental trailer , follow the instructions that the rental agency gives to you. Do not attach safety [...]

• T o eliminate excessive shifting, use a lower gear . This will also assist in transmission cooling. (For additional information, refer to the Driving with a 4 – speed automatic transmission section in this chapter . • Anticipate stops and brake gradually . • Do not exceed the GCWR rating or transmission damage may occur . Servicing after [...]

• affecting driveability , emissions and reliability . Replace the rear axle lubricant any time the axle has been submerged in water . Rear axle lubricant quantities are not to be checked or changed unless a leak is suspected or repair required. RECREATIONAL TOWING (ALL WHEELS ON THE GROUND) An example of recreational towing would be towing your [...]

• Automatic transmission with auxiliary automatic transmission fluid cooling • All-terrain tires • Limited slip and optional axle ratio. Do not install a snowplow and plow with your vehicle until it has been driven at least 800 km (500 miles). Installing the snowplow Read the following instructions before installing a snowplow: • Front GA W[...]

Removing snowplow After removing a snowplow from the vehicle, ensure the vehicle ’ s front toe alignment and front ride height are within specification (reset if required). Snowplowing with your air bag equipped vehicle Y our vehicle is equipped with a driver and passenger air bag Supplemental Restraint System (SRS) The SRS is designed to activat[...]

Transmission operation while plowing • Shift transfer case to 4L (4WD Low) when plowing in small areas at speeds below 8 km/h (5 mph). • Shift transfer case to 4H (4WD High) when plowing larger areas or light snow at higher speeds. Do not exceed 24 km/h (15 mph). • Do not shift the transmission from a forward gear to R (Reverse) until the eng[...]

GETTING ROADSIDE ASSISTANCE T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24 – hours, seven days a week • for the New V ehicle Limited W arranty period of three years o[...]

Canadian customers who require roadside assistance, call 1 – 800 – 665 – 2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. T o obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673; Lincoln vehicle customers call 1 – 800 – 521 – 4[...]

The fuel pump shut-off switch is located in the passenger ’ s foot well, by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. T urn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. T u[...]

Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey ——— 3A Violet V iolet [...]

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 15A Audio 2 5A Powertrain Control Module (PCM), Cluster 3 20A Cigar lighter , Data link connector 4 5A Power mirror switch, Mirror turn signal relays 5 15A Speed control module, Reverse lamp, Climate mode switch, Daytime Running Lamps [...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 7 — Not used 8 5A Radio, Remote entry module, GEM, In-vehicle entertainment system (SuperCrew only) 9 — Not used 10 — Not used 11 30A Front washer pump relay , W iper run/park relay , Wiper HI/LO relay , W indshield wiper motor 12 — Not used 13 20A Stop lamp sw[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 23 10A T railer tow battery Charge relay , T urn/Hazard flasher , 4x4 solenoids, 4x4 relays, Overhead console, 4 – Wheel Anti-lock Brake System (4W ABS) module, EC mirror , Heated seats 24 10A Function selector switch assembly 25 — Not used 26 10A Right-hand low be[...]

Always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and specifications chapter . The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Power Distribution Bo[...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 8 15A* Power door locks, Central Security Module (CSM), Lock relays (not used on SuperCrew) 9 15A* Daytime Running Lamps (DRL), Fog lamps 10 20A* Fuel pump 11 20A* Alternator field 12 20A* Rear auxiliary power point (SuperCrew only) 13 15A* A/C clutch 14 — Not used 15 10A Runn[...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 104 30A** 4x4 shift motor & clutch 105 40A** Climate control front blower 106 20A** Intercooler pump (supercharged engine only) 107 — Not used 108 30A** T railer tow electric brake 109 — Not used 110 30A** Accessory delay relay (Not used on SuperCrew) 111 40A** Ignition [...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 302 — T railer tow battery charge relay 303 — Not used 304 — PCM relay 305 — Fuel pump HI/LO relay (supercharged engine only) 306 — Inertia switch relay (supercharged engine only) 401 — Not used 501 — PCM diode 502 — A/C compressor diode 503 — Not used 601 CB P[...]

If your vehicle is equipped with 4WD, a spare tire of a different size than the road tires should not be used. Use of such a tire could result in damage to driveline components and an increased risk of loss of vehicle control, vehicle rollover , personal injury or death. If your vehicle is equipped with a tire pressure monitoring system, refer to T[...]

2. Attach the spare tire lock key (A) to the jack handle (B). 3. Fully insert the jack handle through the bumper hole and into the guide tube. The key and lock will engage with a slight push and counterclockwise turn. Some resistance will be felt when turning the jack handle assembly . 4. T urn the handle counterclockwise until tire is lowered to t[...]

If the vehicle slips off the jack, you or someone else could be seriously injured. Refer to the instruction sheet (located with the jack) for detailed tire change instructions. 1. Park on a level surface, activate hazard flashers and set the parking brake. 2. Place gearshift lever in P (Park) (automatic transmission) or in the reverse gear (manual [...]

When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the transmission is in P (Park) or in the reverse gear (manual transmission). T o prevent the vehicle from moving when you change the tire, be sure that the parking brake is set and the diagonally opposite[...]

• Rear T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. • Never use the front or rear differential as a jacking point. 8. Remove the lug nuts with the lug wrench. 9. Replace th[...]

• Seven lug nut wheel 12. Stow the flat tire. Refer to Stowing the flat/spare tire. 13. Stow the jack and lug wrench. Make sure the jack is fastened so it does not rattle when you drive. 14. Unblock the wheels. Bolt size Wheel lug nut torque* Nm Lb-ft F-150 (five lug nut wheel): M14 x 2.0 200 150 F-150 with Heavy Payload Package (seven lug nut wh[...]

Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its shift strategy . As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission. Over time, the adaptive learning process will fu[...]

2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . + – + – + – + – Roadside Emergencies 221[...]

4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle ’ s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the ba[...]

Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Remove the jumper cable on the negative (-) connection of the booster vehicle ’ s batte[...]

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle ’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle ’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member , your roadside assistance center . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. If equipped with[...]

damage may occur . Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle. Roadside Emergencies 226[...]

GETTING THE SERVICES YOU NEED At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. It is preferred that you return to the authorized dealer where your vehicle was purchased when warranty repairs are needed. However , you may also take your vehicle to another Ford Motor Company or Ford of Canada dealersh[...]

In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www .ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact [...]

In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state ’ s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the Dispute Settlement Board before taking action under the Magnuson-Moss W arranty Act, or to [...]

• available free to owners and lessees of qualifying Ford Motor Company vehicles. The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this service without notice and without incurring obligations per applicable state law .[...]

• A Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities. What the Board needs T o have your case reviewed [...]

before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made. An oral presentation may be requested by the Board as well. Making a decision Board members review all available information related to each complaint, including oral presentations, and arrive at a fair and impartial decision.[...]

The CAMV AP program is a straight-forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed. This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings. In the CAMV AP program, impartial third-party arbitrators conduct h[...]

If you are in another foreign country , contact the nearest Ford dealership. If the dealership employees cannot help you, they can direct you to the nearest Ford affiliate office. If you buy your vehicle in North America and then relocate outside of the U.S. or Canada, register your vehicle identification number (VIN) and new address with Ford Moto[...]

1. T wo or more repair attempts are made on the same nonconformity likely to cause death or serious bodily injury OR 2. Four or more repair attempts are made on the same nonconformity (a defect or condition that substantially impairs the use, value or safety of the vehicle) OR 3. The vehicle is out of service for repair of nonconformities for a tot[...]

W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo, such as Motorcraft Detail W ash (ZC-3 – A), which is available from your dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Never wash [...]

PAINT CHIPS Y our dealer has touch-up paint and sprays to match your vehicle ’ s color . T ake your color code (printed on a sticker in the driver ’ s door jam) to your dealer to ensure you get the correct color . • Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing[...]

• 4.2L V6 engine • 4.6L V8 and 5.4L V8 engine Cleaning 238[...]

• 5.4L Supercharged V8 engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your dealer . • For routine cleaning, use Motorcraft Detail W ash (ZC-3 – A). •[...]

INSTRUMENT PANEL AND CLUSTER LENS Clean the instrument panel with a damp cloth, then dry with a dry cloth. • A void cleaners or polish that increase the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection. Do not use chemical solvents or strong detergents[...]

For King Ranch F-150 SuperCrew leather seats, refer to separate section in this chapter . • T o clean, use a soft cloth with Motorcraft Deluxe Leather and Vinyl Cleaner (ZC-11 – A). Dry the area with a soft cloth. • T o help maintain its resiliency and color , use the Motorcraft Deluxe Leather Care Kit (ZC-11 – D), available from your autho[...]

CONDITIONING Bottles of King Ranch F-150 Leather Conditioner are available at the King Ranch Saddle Shop. Visit the W eb site at www.krsaddleshop.com , or telephone (in the United States) 1 – 800 – 282 – KING (5464). If you are unable to obtain King Ranch F-150 Leather Conditioner , use another premium leather conditioner . • Apply your fir[...]

FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Y our Ford, Lincoln or Mercury dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Each product[...]

SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a scheduled maintenance guide which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide the necessary parts and service. Check you[...]

4. Block the wheels to prevent the vehicle from moving unexpectedly . Working with the engine on • Automatic transmission: 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Block the wheels to prevent the vehicle from moving unexpectedly . Note: Do not start your engine with the air cleaner removed and do not r[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.2L V6 engine 1. Battery 2. Engine oil filler cap 3. Engine oil dipstick 4. Clutch fluid reservoir (manual transmission) 5. Brake fluid reservoir 6. Power distribution box 7. Engine coolant reservoir 8. Air filter assembly 9. Power steering fluid reservoir 10. T ransmission fluid dipstick (automatic[...]

4.6L V8/5.4L V8 engines 1. Power steering fluid reservoir 2. Clutch fluid reservoir (manual transmission) 3. Engine oil dipstick 4. Brake fluid reservoir 5. Power distribution box 6. Air filter assembly 7. Engine coolant reservoir 8. W indshield washer fluid reservoir 9. Battery 10. T ransmission fluid dipstick (automatic transmission) 11. Engine o[...]

5.4L Supercharged V8 engine 1. Engine oil dipstick 2. Power steering fluid reservoir 3. Brake fluid reservoir 4. Power distribution box 5. Engine coolant reservoir 6. Air filter assembly 7. Intercooler coolant reservoir 8. W indshield washer fluid reservoir 9. Battery 10. T ransmission fluid dipstick 11. Engine oil filler cap 9 8 7 6 5 10 11 1 2 3 [...]

WINDSHIELD WASHER FLUID Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification ESR-M17P5 – A. Refer to Lubricant specifications in this ch[...]

• 4.2L engine • 4.6L/5.4L engine Maintenance and Specifications 250[...]

5. Locate and carefully remove the engine oil level indicator (dipstick). 6. W ipe the indicator clean. Insert the indicator fully , then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MA[...]

Engine oil and filter recommendations Look for this certification trademark. SAE 5W -20 engine oil is recommended. Only use oils “ Certified For Gasoline Engines ” by the American Petroleum Institute (API). Use Motorcraft or an equivalent oil meeting Ford specification WSS-M2C153 – H. SAE 5W -20 oil provides optimum fuel economy and durabilit[...]

BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However , for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the scheduled maintenance guide for the service interval schedules. Keep the electrolyte l[...]

When lifting a plastic-cased battery , excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery . Lift the battery with a battery carrier or with your hands on opposite corners. Keep batteries out of reach of children. Batteries contain sulfuric acid. A [...]

• Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the mileage intervals l[...]

When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “ cold fill level ” or within the “ cold fill range ” as listed on the engine coolant reservoir (depending upon application). • Refer to the Scheduled Maintenance Guide for service interval schedules. • Be sure to re[...]

Do not put engine coolant in the windshield washer fluid container . If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. The cooling system in your vehicle is filled with either green-colored Motorcraft Premium Engine Coolant meeting Ford specification ESE-M97B44 – A or yellow-colored Motorcraft Pre[...]

For vehicles with overflow coolant systems with a non-pressurized cap on the coolant recovery system, add coolant to the coolant recovery reservoir when the engine is cool. Add the proper mixture of coolant and water to the “ cold full ” level. For all other vehicles, which have a coolant degas system with a pressurized cap, or if it is necessa[...]

Recycled engine coolant Ford Motor Company recommends the use of a recycled engine coolant produced by Ford-approved processes in vehicles originally equipped with Motorcraft Premium Engine Coolant (green-colored). However , not all coolant recycling processes produce coolant that meets Ford specification ESE-M97B44 – A. Use of such coolant may h[...]

• Decreased engine coolant concentrations below 40% will decrease the corrosion protection characteristics of the engine coolant and may cause engine damage. • Decreased engine coolant concentrations below 40% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage. • Refer to the chart on the coo[...]

Once the engine temperature cools, the engine can be re-started. T ake your vehicle to a service facility as soon as possible to minimize engine damage. When fail-safe mode is activated Y ou have limited engine power when in the fail-safe mode, so drive the vehicle with caution. The vehicle will not be able to maintain high speed operation and the [...]

Automotive fuels can cause serious injury or death if misused or mishandled. Gasoline may contain benzene, which is a cancer -causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automot[...]

When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be taken to avoid inhaling excess fumes. The flow of fuel through a fuel pump nozzle can produce static electricity , which can cause a fire if fue[...]

be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you [...]

Supercharged engines Y our vehicle is designed to use “ Premium ” unleaded gasoline with an (R+M)/2 octane rating of 91 or higher for optimum performance. The use of gasolines with lower octane ratings may degrade performance. W e do not recommend the use of gasolines labeled as “ Premium ” in high altitude areas that are sold with octane r[...]

Running out of fuel A void running out of fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: • Y ou may need to cycle the ignition from OFF to ON several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine. • Y our “ Service Engine Soon ” ind[...]

vehicle after the fuel gauge indicates empty , you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank. For consistent results when filling the fuel tank: • T urn the engine/ignition switch to the off position prior to refueling, an error in the reading will re[...]

Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy . • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel e[...]

• Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy . • T o maximize the fuel economy , drive with the tonneau cover installed (if equipped). • Using fuel blended with alcohol may lower fuel economy . • Fuel economy may decrease with lower [...]

The scheduled maintenance items listed in the scheduled maintenance guide are essential to the life and performance of your vehicle and to its emissions system. If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivale[...]

• First, at least 10 minutes of driving on an expressway or highway . • Next, at least 20 minutes driving in stop-and-go, city-type traffic with at least four idle periods. Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle. The engine must warm up to its no[...]

4. Check the fluid level in the reservoir . It should be between the MIN and MAX lines. Do not add fluid if the level is in this range. 5. If the fluid is low , add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and MAX lines. Be sure to put the cap back on the reservoir . BRAKE FLUID Checking and[...]

Brake fluid is toxic. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes. Seek medical attention if irritation persists. If taken internally , drink water and induce vomiting. Seek medical attention immediately . If you use a brake fluid that is not DOT 3, you will cause permanent damage to your brakes. Do not let the fl[...]

1. Clean the reservoir cap before removal to prevent dirt and water from entering the reservoir . 2. Remove cap and rubber diaphragm from reservoir . 3. Add fluid until the level reaches the step in the reservoir . 4. Reinstall rubber diaphragm and cap onto reservoir . T RANSMISSION FLUID Checking automatic transmission fluid (if equipped) Refer to[...]

4. Latch the gearshift lever in P (Park) and leave the engine running. 5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary , refer to Identifying components in the engine compartment in this chapter for the location of the dipstick. 6. Install the dipstick making sure it is fully seated in the filler tube. 7. Remov[...]

The transmission fluid should be in this range if at ambient temperature (10 ° C-35 ° C [50 ° F-95 ° F]). High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an over[...]

Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely . Use on[...]

Checking and adding transfer case fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to Lubricant Specifications in this chapter . DRIVELI[...]

AIR FILTER MAINTENANCE Refer to the scheduled maintenance guide for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the Motorcraft air filter element listed. Refer to Motorcraft Part Numbers . Note: Do not start your engine with the air cleaner removed and do not remove it while the engi[...]

INFORMA TION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called T ire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • T readwear 200 T raction AA T emperature A These T ire Quality Grades are [...]

The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. T emperature A B C The temperature grades are A (the highest), B and C, representing the tire ’ s resistance to the generation of heat and its ability to dissipate[...]

them as indicated in the scheduled maintenance guide. If you notice that the tires wear unevenly , have them checked. The following procedure applies to vehicles equipped with single rear wheels, if your vehicle is equipped with dual rear wheels it is recommended that only the front wheels be rotated (side to side). • Four tire rotation • Five [...]

Replacing the tires Replace the tires when the wear band is visible through the tire treads. Due to exposure to the elements and exhaust you should replace the spare tire when you replace the other tires. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification La[...]

tires and chains. If you need to use chains, it is recommended that steel wheels (of the same size and specifications) be used, as chains may chip aluminum wheels. Follow these guidelines when using snow tires and chains: • Use only SAE Class S chains. • Install chains securely , verifying that the chains do not touch any wiring, brake lines or[...]

2 If a spark plug is removed for inspection and replaced, it must be reinstalled in the same cylinder . If a spark plug needs to be replaced, use only spark plugs with the service number suffix letter as shown above. 3 Use only AGSF-12FM1 spark plugs for replacement. REFILL CAPACITIES Fluid Ford Part Name Application Capacity Brake fluid and clutch[...]

Fluid Ford Part Name Application Capacity Intercooler coolant 1 Motorcraft Premium Engine Coolant (green-colored) or Motorcraft Premium Gold Engine Coolant (yellow-colored) 5.4L Supercharged V8 engine 4.0L (4.2 quarts) Engine oil (includes filter change) Motorcraft SAE 5W -20 Premium Synthetic Blend Motor Oil All 5.7L (6.0 quarts) Fuel tank N/A 4x4[...]

Fluid Ford Part Name Application Capacity T ransmission fluid 3 Motorcraft MERCON 威 AT F 5-speed manual 3.5L (3.75 quarts) 4 Automatic- 4R100 (4x2) 16.1L (17.0 quarts) 4 Automatic- 4R100 (4x4) 16.7L (17.7 quarts) 4 Motorcraft MERCON 威 V AT F Automatic- 4R70W 13.2L (13.9 quarts) 4 Front axle Motorcraft SAE 75W -90 Premium 4x4 Front Axle Lubrican[...]

in an automatic transmission that requires use of the MERCON 威 type fluid. However , these dual usage fluids may be used in transmissions that require the MERCON 威 V type fluid. MERCON 威 and MERCON 威 V type fluids are not interchangeable. DO NOT mix MERCON 威 and MERCON 威 V . Use of a transmission fluid that indicates dual usage (MERCON [...]

LUBRICANT SPECIFICATIONS Item Ford part name or equivalent Ford part number Ford specification Front axle (4X4) Motorcraft SAE 75W -90 Premium 4x4 Front Axle Lubricant XY -75W90-TQL WSP-M2C201-A Rear axle Motorcraft SAE 75W -140 High Performance Synthetic Rear Axle Lube 1 XY -75W140 – QL WSL-M2C192-A Brake fluid and clutch fluid Motorcraft High P[...]

Item Ford part name or equivalent Ford part number Ford specification Hinges, latches, striker plates, fuel filler door hinge and seat tracks. Multi-Purpose Grease XG-4 or XL-5 ESR-M1C159-A or ESB-M1C93-B Lock cylinders Motorcraft penetrating and lock lubricant Motorcraft XL-1 none T ransmission /steering/parking brake linkages and pivots, brake an[...]

of T raction-Lok axles. Add 236 ml (8 oz.) of Additive Friction Modifier C8AZ-19B546-A or equivalent meeting Ford specification EST -M2C118-A for complete refill of 10.25 and 10.5 inch T raction-Lok axles. 2 Ensure the correct automatic transmission fluid is used. T ransmission fluid requirements are indicated on the dipstick or on the dipstick han[...]

VEHICLE DIMENSIONS Styleside Dimension Body Style Regular Cab 4x2 Regular Cab 4x4 Super Cab 4x2 Super Cab 4x4 (1) Overall length 5256 mm (206.9 in) (SWB) 5729 mm (225.5 in) (L WB) 5264 mm (207.2 in) (SWB) 5736 mm (225.8 in) (L WB) 5728 mm (225.5 in) (SWB) 6201 mm (244.1 in) (L WB) 5735 mm (225.8 in) (SWB) 6208 mm (244.4 in) (L WB) (2) Overall width[...]

Flareside Dimension Body Style Regular Cab 4x2 Regular Cab 4x4 Super Cab 4x2 Super Cab 4x4 (1) Overall length 5255 mm (206.9 in) 5263 mm (207.2 in) 5728 mm (225.5 in) 5735 mm (225.8 in) (2) Overall width 2014 mm (79.3 in) 1 2030 mm (79.9 in) 1 2014 mm (79.3 in) 1 2030 mm (79.9 in) 1 (3) Overall height 1846 mm (72.7 in) 1915 mm (75.4 in) 1849 mm (72[...]

1 4 1 4 Maintenance and Specifications 294[...]

F-150 SuperCrew Dimension Body Style SuperCrew 4x2 mm (in) SuperCrew 4x4mm (in) (1) Overall length 5738 (225.9) 5745 (226.2) (2) Overall width 2009 (79.1) 1 2029 (79.9) 1 (3) Overall height 1878 (73.9) 2 1953 (76.9) (4) Wheel base 3518 (138.5) 3525 (138.8) (5)T rack front/rear 1661 (65.4) 1 661 (65.4) 1 V ehicle width, including mirrors: 2293 mm (9[...]

IDENTIFYING YOUR VEHICLE Certification label The National Highway T raffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the front door latch pillar on the driver ’ s side. 1 4 Maintenance and Specificat[...]

V ehicle identification number (VIN) The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number .) 1. W orld manufacturer identifier 2. Brake type and gross vehicle weight rating (GVWR) 3. V ehicle line[...]

FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for your vehicle through your local authorized Ford, Lincoln, Mercury or Ford of Canada dealer . These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic a[...]

Manual sliding rear window Power sliding rear window Remote start system T ire step T ravel equipment Cargo cage (SuperCrew only) Bed mount bike carrier Bed tent Fog lights Hitch mount bike carrier Inside mirror with compass display Inside mirror with compass and temperature display Off road lights Outside signal mirror (available only with power m[...]

Cargo cover Cargo liner Chrome grill insert Diamond plate, bed rail caps Diamond plate, front box protector Diamond plate, splash guards Diamond plate, tool box Door edge guards Carpet floor mats Fender flares Flat splash guards Front end covers (full) Grill guard/brush guard Hood deflectors Leather wrapped steering wheel Molded splash guards Molde[...]

communications systems - such as two-way radios, telephones and theft alarms - that are equipped with radio transmitters. Any such equipment installed in your vehicle should comply with FCC or CRTC regulations and should be installed only by a qualified service technician. • Mobile communications systems may harm the operation of your vehicle, pa[...]

A ABS (see Brakes) ..................... 165 Accessory delay .......................... 82 Air bag supplemental restraint system ................................ 135 – 136 and child safety seats ............ 137 description .............................. 136 disposal .................................... 140 driver air bag ........................[...]

Child safety seats ......................147 attaching with tether straps .. 152 in front seat ............................148 in rear seat ...................... 148, 151 Cleaning your vehicle engine compartment .............. 237 exterior .................................... 242 instrument panel ....................240 interior ..................[...]

cleaning ................................... 237 coolant ..................................... 255 fail-safe coolant ...................... 260 idle speed control ................... 253 lubrication specifications ...... 289, 291 refill capacities ........................ 285 service points .................. 246 – 248 starting after a collision [...]

GVWR (Gross V ehicle W eight Rating) ....................................... 190 calculating ....................... 190, 192 definition ................................. 190 driving with a heavy load ......190 location .................................... 190 H Hazard flashers ......................... 204 Head restraints .........................[...]

brake .......................................... 12 charging system ........................ 13 check coolant ............................ 13 cruise indicator ......................... 14 door ajar .................................... 14 engine oil pressure ................... 13 fuel cap light ............................. 12 high beam ...........[...]

locking/unlocking doors ........................ 101, 103 – 104 panic alarm ............................. 104 replacement/additional transmitters ............................. 105 replacing the batteries ........... 104 Roadside assistance .................. 203 S Safety belts (see Safety restraints) ....................15, 122 – 127 Safety def[...]

fluid, checking and adding (automatic) ............................. 274 fluid, checking and adding (manual) ................................. 277 fluid, refill capacities .............. 285 lubricant specifications .. 289, 291 manual operation .................... 172 T ransmission control indicator light ..........................................[...]

309[...]

310[...]

311[...]

312[...]